Search Results

Search found 14157 results on 567 pages for 'drive failure'.

Page 75/567 | < Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >

• Add Mirror for volumes other than the last one in Windows 7 (disk "not up-to-date")

  - by rakslice

  I'm using Windows 7 x64 Ultimate. I have an existing 4TB disk with 3 NTFS volumes, a new 3TB blank disk, and I'm trying to mirror the volumes onto the new disk. My Windows install is on an SSD which is Disk 0. The 4TB disk with volumes is Disk 1, and the new blank disk is Disk 2. I can add a mirror successfully for the last volume, but when I try to add a mirror for the first volume I immediately get errors (see below). Is there something I special I need to do to add a mirror for a volume other than the last one? More info: I opened Disk Management, right-clicked on the first volume on the existing disk, went to Add Mirror, and selected the new disk. The first time I did this I was prompted to convert the new disk to a Dynamic Disk, which I approved. Subsequently I got a message: The operation failed to complete because the Disk Management console view is not up-to-date. Refresh the view by using the refresh task. If the problem persists close the Disk Management console, then restart Disk Management or restart the computer. I've refreshed disk management, restarted the computer, and converted the new disk to basic and back to dynamic, but I still get that error message. Looking around for suggestions of a workaround, I saw a suggestion to use the diskpart command line tool. Running diskpart from the Start Menu as Administrator, I did select volume 2 (the first volume I want to mirror) and then add disk 2 (the new disk), and received a somewhat similar error: Virtual Disk Service error: The disk's extent information is corrupted. DiskPart has referenced an object which is not up-to-date. Refresh the object by using the RESCAN command. If the problem persists exit DiskPart, then restart DiskPart or restart the computer. A rescan appears to be successful: DISKPART> select disk 2 Disk 2 is now the selected disk. DISKPART> rescan Please wait while DiskPart scans your configuration... DiskPart has finished scanning your configuration. but attempting to add the mirror again resulted in the same error. The only similar report I found online was this: http://www.sevenforums.com/hardware-devices/335780-unable-mirror-all-but-last-partition-drive.html Based on that I attempted to mirror the last volume on the disk to the new disk using diskpart, and that started successfully -- it is currently resynchronizing. More Background: In the course of dealing with a failing 3TB hard drive, I bought a replacement 4TB drive and installed it, then copied the partitions from the failing drive to it using Minitool Partition Wizard Home, and then removed the failing drive and was up and running again normally. Now I've received a warranty replacement for the failing drive, and installed it, and now I'm attempting to mirror my partitions to it.

  Read the article

• 10,000 RPM HDD (WD VelociRaptor) vs SSD for OS?

  - by GiH

  I currently have a 10,00RPM 150GB Raptor that I use for Vista. I'm about to upgrade to Windows 7, and while doing that I thought I'd buy another drive and install Ubuntu 9.10 on it. I don't want to partition the current drive I have, but I don't need 150GB for another OS. So, I'm having trouble deciding whether its worth it to buy a 64 GB SSD at the same price point as the 150GB WD VelociRaptor? Or should I just get a 7,200 RPM drive for really cheap (around $50)? Would it be better to use an SSD for the OS than a mechanical drive? I could always get a 32GB SSD too... Oh, and I don't want to virtualize Ubuntu because I'm going to be testing to see the differences in networking and overall performance.

  Read the article

• HP Usb storage Format tool : Error

  - by Srin

  I have a 2 GB Kingston Usb drive. This is working fine- I am able to format and access from 'My computer' I am trying to format this drive using HP USB Storage format tool to load a bootable image on to the drive, it says "device media is write protected" OS : Windows XP what could be wrong ? Thanks!

  Read the article

• Data Recovery needed with a Sector Zero problem on a HDD

  - by Jay Robins

  Left my computer (running XP) copying files to an external drive. Came back a few hours later, and the laptop was pretty hot and had frozen (Ironic aint it). Forced a reboot, and the laptop HDD hasnt worked since. Set it up in an external enclosure, but XP cant mount the HDD to a drive letter, but is able to recognize the manufacturer and drive size (Hitachi-320GB). No noise or rattling when the drive is spinning, but I cant get anything off of it, since i cant mount it, or see much of anything. Computer repair shop ran some software tests and says it came back with a "Zero Sector bad" message, and need to send it to a professional data recovery service. Any other options or ideas, before I have to spend thousands of dollars to recover my data? Any help would be GREATLY appreciated!!! I'm desperate and a poor student! Thanks in Advance, -Jay

  Read the article

• Crashes and freezes after fixing "BOOTMGR is missing" error

  - by Greg-J

  I came back from a 3-day weekend to a computer that was off. I leave my PC on 24/7, so this was odd. Turn it on to get the dreaded "BOOTMGR is missing" screen. Two attempts at Windows Recovery and it booted into Windows fine. After an hour or so, I get a frozen Chrome and my start bar disappears. Ctrl+Alt+Del brings up an error box telling me that Ctrl+Alt+Del failed to work properly. Clicking on any open application triggers an error (I can't recall the error now, but it essentially just said that the application couldn't be found running or something along those lines). I restart, and again, the same thing happens after a while of use. I turn it on, install the 47 updates I have or so, and then restart it. After a while of use (under an hour), it just freezes completely. My thoughts are: SSDs, RAM or PS. My system specs below: (RAID0) 2 x Crucial M4 CT128M4SSD2 2.5" 128GB SATA III MLC Internal Solid State Drive (SSD) CORSAIR Vengeance 16GB (4 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Desktop Memory Model CML16GX3M4A1600C9 CORSAIR HX Series HX750 750W ATX12V 2.3 / EPS12V 2.91 SLI Ready CrossFire Ready 80 PLUS GOLD Certified Modular Active 1 x ASUS Maximus IV Gene-Z/GEN3 LGA 1155 Intel Z68 HDMI SATA 6Gb/s USB 3.0 Micro ATX Intel Motherboard 1 x Hitachi GST Deskstar 7K1000.C 0F10383 1TB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive 1 x Intel Core i7-2600K Sandy Bridge 3.4GHz (3.8GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 1 x SAPPHIRE 21197-00-40G Radeon HD 7970 3GB 384-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card 1 x Noctua NH-D14 120mm & 140mm SSO CPU Cooler This is all crammed in a pretty small case (NZXT Vulcan) and has been running perfectly problem-free since January. The only thing out of the ordinary is that there is a fan in the case that is now making noise whereas the case has previously been completely silent. I have no reason to believe this is anything more then correlation, but felt it is worth mentioning. I believe it MAY be the SSDs simply because of the BOOTMGR error, but not sure how to test that theory. My belief that it may be the RAM is simply from experience with frozen machines. I haven't had the time to memtest it, but will. The PS being the culprit is something I've picked up by reading similar threads on various forums, and it seems plausible. I am unsure how to test this though. ANY insight whatsover would be greatly appreciated!

  Read the article

• Building a PC for Work and play? [closed]

  - by Derek Organ

  Ok, Its been a long time since I build my own PC so I'm looking to get back into it again and build a new one. First off budget is about €800 excluding the monitor and windows 7 licence and mouse. (just bought a new g500) I plan on using my computer for work, lots of applications open at once but none particularly excessive (photoshop being the most demanding, mostly coding tools) I also use it for some gaming, e.g. COD, Starcraft etc. One thing I do want to do eventually is get a really good monitor with hight resolution and maybe 27" so the graphics card needs to be able to make best use of that. So a few questions 1) Is the bottle neck in performance mostly still the harddrives? 2) Aren't most processors e.g. i5 etc even i3 so far a head of other bottlenecks it makes litte difference the higher you go. Isn't the Graphics card dealing with heavy graphics so what really slows because of a slow CPU? So from this my thinking is to get a SSD drive as my primary drive for OS etc and have loads of memory e.g. 6-8GB and a decent mid level graphics card? It doesn't seem at my level worth spending much on CPU and any other parts really. I basic parts off the top of my head Case, Motherboard CPU SSD Drive SATA Drive Power Supply Memory Cooling (fan?) Graphics Card Network Card Keyboard DVD drive Mouse Windows Monitor Am I missing anything? Any helpful tips or general education much appreciated. Thanks, Derek

  Read the article

• Linux for a laptop? [closed]

  - by spriteless

  I would like to install Linux on a laptop. So I have emptied the hard drive, and can boot off a CD. So far I have failed to format the hard drive to Linux, to install Linux, and to change it so that I don't have to hit escape when loading in order to boot from CD (or get Linux on the hard drive and boot to it). The old laptop has 640 MB RAM, 600*800 screen, a CD drive and USB mouse and floppy drives. I eventually mean to use it to look at PDFs if possible, or RTFs that I converted from PDFs if not.

  Read the article

• How do I remove a MyBook's "WD SmartWare" virtual CD from my desktop?

  - by Justin Love

  I recently got a Western Digital MyBook external hard drive to enable Time Machine. It has it's software installed on a "virtual CD" called "WD SmartWare" which shows up on the desktop any time the drive is plugged in. Since I will use this virtual drive only very rarely, how can I hide it from the desktop, while allowing other CDs to show up?

  Read the article

• Troubleshooting: Monitor never turns on, system fans running, DVD-ROM does not open.

  - by Wesley

  Hi all, Here are my specs beforehand: ECS P4VXASD2+ (V5.0) motherboard FSB 533MHz Intel Pentium 4 2.40A GHz Prescott Socket 478 2x 256MB PC2100 DDR RAM, 2x 256MB PC133 SDRAM CoolMax 350W PSU DVD-ROM - will edit with brand & model 128MB ATi Radeon 9800 Pro AGP No hard drive So, I just put those parts together today and I tried to power it up, with the monitor connected to the Radeon 9800 in the AGP slot (mobo does not have VGA port). After turning it on, the CPU fan, graphics fan and system fan go on. However, the monitor remains in standby mode, despite being plugged in. Also, after pushing the button on the DVD-ROM drive, it does not open. I've used the DVD-ROM drive before with absolutely no issues. The graphics card was slightly buggy when I put it on another machine, which was left outside in winter weather for 3 months. (Still that computer's integrated graphics worked fine.) CMOS battery was replaced and jumpers are all set correctly. Now, I'm wondering whether the motherboard, CPU, PSU or GPU is the problem. What can I do to test which part is the problem? Just to clarify, I don't have a hard drive, so I usually boot Ubuntu from the disc drive. Anyways, thanks in advance!

  Read the article

• Move virtual machine hard disk to a separate physical hard disk for better performance?

  - by joeeoj

  I have a dual-core machine with the host OS and many guest virtual OSs. Although I have 8GB of RAM, I notice a slowdown when I turn some virtual machine on (and it takes only 1GB RAM). I was told that I should move virtual machine hard disk file to a separate (another) physical hard drive in my PC to get better performance. This way the head of the hard disk would not have to jump from the virtual OS to the host OS as each hard drive would have its own head to deal with the OS: hard drive 1 head for host OS and hard drive 2 head for guest OS. Is this true? Should I get another hard disk only for virtual machine hard disk files?

  Read the article

• OS Missing? Messed up the MBR on Win7 64-bit

  - by hom3lesshom3boy

  I have a Windows 7 machine with two hard drives: a 1TB C: drive and 500GB J:. I had Windows XP installed on C: and Windows 7 installed on J:. I installed Windows 7 after Windows XP from an installer .exe I (legally) bought and downloaded. It, and all of my other files, are sitting on my J: drive intact. While under my Windows 7 install, a few days ago I decided to use Priform's CCleaner and use its DriveWipe utility to wipe the C: drive. 1% into the process, I cancelled and attempted to use it again. It gives me an error saying it can't format the drive, so I poke around the Internet a bit, give up, and restart my computer. I first get an "OS is missing" error after the computer boots past the BIOS. I downloaded and put UBCD on a bootable USB to use another drivewiping tool to completely erase the C: drive, hoping it'll take the problem with it. No luck. I try to use TestDisk to make my J: my primary active drive, but no luck. I still get the "OS is missing" error. Or sometimes it'll hang at Verifying DMI Pool. Or sometimes I'll get the "NTLDR is missing" error. I get hold of Hiren's and put it on another bootable USB. I first I tried the Boot Windows 7 from Hard Drive option, and I get "Error 15: File Not Found". I tried the "Fix 'NTLDR is Missing'" option (I'm not quite sure why this is even showing up, since I'm trying to get into a HDD with Windows 7 installed. Probably messed up somewhere when I used TestDisk) and I get this list: I'll run through the error messages I get: 1st Try - Windows could not start because the following file is missing or corrupt: \system32\hal.dll 2nd Try - Windows could not start because the following file is missing or corrupt: \system32\ntoskrnl.exe 3rd Try - Windows could not start because of a computer disk hardware configuration problem. Could not read from the selected boot disk. Check boot path and disk hardware. 4th - 8th Try - Same as #3 9th Try - I/O Error accessing boot sector file multi(0)disk(0)fdisk(0)\BOOTSEC.DOS. And computer freezes. 10th Try - computer restarts Needless to say, not a single one of those works. I then tried to open up the Windows 7 exe I have sitting on my J: from the Mini-XP OS on Hiren's, but it won't run because I'm trying to run a 64-bit file from a 32-bit exe. At least, that's the problem according to these guys: http://social.technet.microsoft.com/...-b2f54e9c7d18/ I then borrowed a 64-bit Windows Home Premium CD from a friend to get to the recovery options. But I get the error message: This version of System Recovery Options is not compatible with the version of Windows you are trying to repair. Try using a recovery disc that is compatible with this version of Windows. I pressed Shift + F10 to get to the Command Prompt directly. These are the exact steps I took from there (paraphrased a little): X:\Sources>bootrec /Fixmbr The operation completed successfully. X:\Sources>bootrec /Fixboot The operation completed successfully. I restarted my computer, but it still didn't work. I unplugged the C: drive, then tried bootrec and Diskpart: X:\Sources> bootrec.exe X:\Sources> bootrec /RebuildBcd Total identified Windows installations: 1 [1] \\?\GLOBALROOT\Device\HarddiskVolume1\Windows Add installation to bootlist? Yes(Y)/No(N)/All(A):y The requested system device cannot be found. X:\Sources>DiskPart DISKPART> List Disk Disk # Status Size Free Dyn Gpt Disk 0_Online_465GB_0B_______* Disk 1 Online 1000MB 0B (this is Hiren's on a bootable usb) DISKPART> Select Disk 0 Disk 0 is now the selected disk. DISKPART> List Partition Partition # Type Size Offset Partition 1 System 465GB 31KB DISKPART> Select Partition 1 Partition 1 is now the selected partition DISKPART> Active The selected disk is not a fixed MBR disk. The ACTIVE command can only be used on fixed MBR disks. DISKPART> exit Leaving Diskpart... X:\Sources>bootrec /Fixmbr The operation completed successfully. X:\Sources>bootrec /Fixboot The operation completed successfully. Before I go any further, is there anything I'm overlooking/doing wrong? All I care about is making the J: and Windows 7 bootable again. SPECS: Windows 7 Professional 64-Bit GIGABYTE - Motherboard - Socket 775 - GA-P35-DS3R (rev. 2.1) Crucial Ballistix 2048MB PC6400 DDR2 800MHz (2x2GB) Intel Core 2 Duo E6700 Processor (2.6 (6GHZ) I think... not sure anymore C: HDD - SAMSUNG HD103UJ (1TB, not plugged in) J: HDD - WDC WD5000AKS-00V1A0 (500GB)

  Read the article

• Recover data from phyiscally damaged harddrive. What are my options?

  - by Michael Kniskern

  I was trying to replace the power supply in my desktop PC and ended up physically damaging the data connection from the hard drive to the motherboard. The plastic shelf for the copper prongs on the hard drive broke into the cable. Here is a picture of my handy work: Picture of damage I went to Best Buy Geek Squad to discuss my options and they said that they will need to send it to the recover center it could cost anywhere between $250 to $1600 USD to recover the data out the hard drive Is this reasonable for data recovery from a phyiscally damaged hard drive? Are there any other options I can explore? I am going to talk to the data doctors to see what my options are.

  Read the article

• Cant install windows 7(boot problem)

  - by Vadiklk

  First of all, I cant boot my windows 7. I get a black screen with a cursor up in the left corner. So, I tried using windows 7 installation which I've put on my flash drive. To boot from the drive, I've changed the boot order to boot from the drive first. It boots but does not find any HDD to install the windows on(which is pretty logic, I dont boot the HDD soon enough for the installer). but if i put the HDD in front of the flash drive in the boot order, it will just try to load windows 7 and i will get the black screen again. I've tried putting the HDD first and clicking f8 a lot. All I've got is an error. Something about some software change. I dunno. Help me please, cant do anything with my laptop till then.

  Read the article

• What are the different Partition Types listed in gparted?

  - by keithterrill

  I am reformatting an older 40meg drive using gparted from within a Linux distro. The drive had no partitions and no partition table, so I am creating a new Partition Table via the Advanced option. The default partition type is msdos, which I think is the same as MBR in parted. The description sounds right: maximum of 4 primary partitions, or 3 primary and 1 extended partition, maximum of 2 tb with 512b sectors. There are a number of other options, gpt being one. Which I would use if the drive was greater than 2 tb. The following partition types are also available: apx, amiga, bsd, dvh, mac, pc98, sun, loop. The question: what are these other types and where can I find a description or discussion about them? Secondary question: is there any reason to not use gpt on a smaller drive? Thank-you

  Read the article

• How to reduce java concurrent mode failure and excessive gc

  - by jimx

  In Java, the concurrent mode failure means that the concurrent collector failed to free up enough memory space form tenured and permanent gen and has to give up and let the full stop-the-world gc kicks in. The end result could be very expensive. I understand this concept but never had a good comprehensive understanding of A) what could cause a concurrent mode failure and B) what's the solution?. This sort of unclearness leads me to write/debug code without much of hints in mind and often has to shop around those performance flags from Foo to Bar without particular reasons, just have to try. I'd like to learn from developers here how your experience is. If you had previous encountered such performance issue, what was the cause and how you addressed it? If you have coding recommendations, please don't be too general. Thanks!

  Read the article

• Hard Disk Not Counting Reallocated Sectors

  - by MetaNova

  I have a drive that is reporting that the current pending sectors is "45". I have used badblocks to identify the sectors and I have been trying to write zeros to them with dd. From what I understand, when I attempt writing data directly to the bad sectors, it should trigger a reallocation, reducing current pending sectors by one and increasing the reallocated sector count. However, on this disk both Reallocated_Sector_Ct and Reallocated_Event_Count raw values are 0, and dd fails with I/O errors when I attempt to write zeros to the bad sectors. dd works fine, however, when I write to a good sector. # dd if=/dev/zero of=/dev/sdb bs=512 count=1 seek=217152 dd: error writing ‘/dev/sdb’: Input/output error Does this mean that my drive, in some way, has no spare sectors to be used for reallocation? Is my drive just in general a terrible person? (The drive isn't actually mine, I'm helping a friend out. They might have just gotten a cheap drive or something.) In case it is relevant, here is the output of smartctl -i : Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD15EARS-00Z5B1 Serial Number: WD-WMAVU3027748 LU WWN Device Id: 5 0014ee 25998d213 Firmware Version: 80.00A80 User Capacity: 1,500,301,910,016 bytes [1.50 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Oct 18 17:47:29 2013 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled UPDATE: I have run shred on the disk, which has caused Current_Pending_Sector to go to zero. However, Reallocated_Sector_Ct and Reallocated_Event_Count are still zero, and dd is now able to write data to the sectors it was previously unable to. This leads me with several other questions: Why aren't the reallocations being recored by the disk? I'm assuming the reallocation took place as I can now write data directly to the sector and couldn't before. Why did shred cause reallocation and not dd? Does the fact that shred writes random data instead of just zeros make a difference?

  Read the article

• SQL Server database filled the hard drive and freeing up space isn't possible

  - by Jon

  I have a database in SQL Server 2008 on a 1Tb hard drive and it filled the drive, there is only 4Kb free. The MDF file is 323Gb and the LDF is 653Gb. The hard disk this DB is on has no other files on it other than the MDF and LDF so it's impossible to free up any space on the drive. The main hard disk is smaller but there is enough room to transfer the MDF to that drive, in case that helps. This server is overseas at a customer site and it's not possible at the moment to add more disk space to the server. It's also not possible to delete any records because the DB is in a failed mode (due to no disk space) and it doesn't respond to most commands. The Db is currently in full recovery mode which is why the LDF file is so large. This DB really doesn't need to be in full recovery so going forward we plan on switching it to simple mode which will save us a lot of space. I also don't care about losing the LDF file, but I need all of the data. I've spent a lot of time looking for a way out of this problem but everything I've found first involves either freeing up disk space or adding more disk space, neither of which is an option at this time. I'm stuck and any help would be greatly appreciated. I get the following log when trying to switch the DB to online mode. Msg 945, Level 14, State 2, Line 3 Database 'DBNAME' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. Msg 5069, Level 16, State 1, Line 3 ALTER DATABASE statement failed. Msg 1101, Level 17, State 12, Line 3 Could not allocate a new page for database 'DBNAME' because of insufficient disk space in filegroup 'DEFAULT'. Create the necessary space by dropping objects in the filegroup, adding additional files to the filegroup, or setting autogrowth on for existing files in the filegroup. I've found the following solutions but none work due to having no disk space on that drive, and since the DB is in a failed state I can't run most commmands. - DBCC SHRINKFILE - can't be run because doing a 'use DBNAME' fails - Detaching the DB and then changing the location of the MDF/LDF files, this fails because the DB is in an offline mode so you can't run detach. I'm at a loss about what else to try. Thanks.

  Read the article

• How can I create bootable DOS usb stick?

  - by Grzenio

  I need to use this utility to change one of the parameters of my new WD hard drive: http://support.wdc.com/product/download.asp?groupid=609&sid=113&lang=en It has truly unreadable instructions: Extract wdidle3.exe onto a bootable medium (floppy, CD-RW, network drive, etc.). Boot the system with the hard drive to be updated to the medium where the update file was extracted to. Run the file by typing wdidle3.exe at the command prompt and press enter. I understand that this bootable medium should be some version of DOS? How can I make my USB stick a bootable medium compatible with this utility (I don't have a diskette drive)? I have Windows 7 and Debian Linux installed.

  Read the article

• How to protect files/folders from being copied/moved/deleted/cut on windows

  - by Sean Lee

  I need to share data on an external drive that will be handed over to someone else, and I would like to achieve the following: (1) protect all the files and folders from being copied/moved/deleted/cut on windows system (2) files are browsable and media playable, but it stays inside the drive (3) the same behavior if drive is plugged on linux system, or not accessible at all is fine too. How can I do these without using paid software?

  Read the article

• Run disk error check on NTFS file?

  - by paulius_l

  I have a feeling that my system hard drive is dying. Benchmark kind of enforces it. Here is the benchmark of my system hard drive during low system activity: And here is the benchmark of backup drive: Furthermore, there are some files which I just can't touch because I get CRC errors and the hard drive activity spikes to 100% with operating speeds less than 1 MB/s while working with such files. I haven't yet tried swapping SATA cable as I have read this might cause the problems. Anyway, I would like to run some tests on specific clustsers where those files I am interested in are stored. I don't want to do the full chkdsk because it takes a very long time. I would like to either find the utility which executes the disk check directly on the clusters where the file belongs or a couple utilities where one tells me the cluster locations and another can check just those locations. How do I check and possibly fix disk errors where the files I am interested in are stored? Edit: S.M.A.R.T. info:

  Read the article

• Instance Failure in asp.net

  - by user85511

  I have a web application that is working perfectly in my system. However, when I copied it to another system, I couldn't login to the application. There is an error: Server Error in '/' Application. -------------------------------------------------------------------------------- Instance failure. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.InvalidOperationException: Instance failure. Source Error: An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Stack Trace: [InvalidOperationException: Instance failure.] System.Data.SqlClient.TdsParser.Connect(ServerInfo serverInfo, SqlInternalConnectionTds connHandler, Boolean ignoreSniOpenTimeout, Int64 timerExpire, Boolean encrypt, Boolean trustServerCert, Boolean integratedSecurity, SqlConnection owningObject) +4858423 System.Data.SqlClient.SqlInternalConnectionTds.AttemptOneLogin(ServerInfo serverInfo, String newPassword, Boolean ignoreSniOpenTimeout, Int64 timerExpire, SqlConnection owningObject) +90 System.Data.SqlClient.SqlInternalConnectionTds.LoginNoFailover(String host, String newPassword, Boolean redirectedUserInstance, SqlConnection owningObject, SqlConnectionString connectionOptions, Int64 timerStart) +257 System.Data.SqlClient.SqlInternalConnectionTds.OpenLoginEnlist(SqlConnection owningObject, SqlConnectionString connectionOptions, String newPassword, Boolean redirectedUserInstance) +221 System.Data.SqlClient.SqlInternalConnectionTds..ctor(DbConnectionPoolIdentity identity, SqlConnectionString connectionOptions, Object providerInfo, String newPassword, SqlConnection owningObject, Boolean redirectedUserInstance) +189 System.Data.SqlClient.SqlConnectionFactory.CreateConnection(DbConnectionOptions options, Object poolGroupProviderInfo, DbConnectionPool pool, DbConnection owningConnection) +4859187 System.Data.ProviderBase.DbConnectionFactory.CreatePooledConnection(DbConnection owningConnection, DbConnectionPool pool, DbConnectionOptions options) +31 System.Data.ProviderBase.DbConnectionPool.CreateObject(DbConnection owningObject) +433 System.Data.ProviderBase.DbConnectionPool.UserCreateRequest(DbConnection owningObject) +66 System.Data.ProviderBase.DbConnectionPool.GetConnection(DbConnection owningObject) +499 System.Data.ProviderBase.DbConnectionFactory.GetConnection(DbConnection owningConnection) +65 System.Data.ProviderBase.DbConnectionClosed.OpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory) +117 System.Data.SqlClient.SqlConnection.Open() +122 System.Web.DataAccess.SqlConnectionHolder.Open(HttpContext context, Boolean revertImpersonate) +87 System.Web.DataAccess.SqlConnectionHelper.GetConnection(String connectionString, Boolean revertImpersonation) +221 System.Web.Security.SqlMembershipProvider.GetPasswordWithFormat(String username, Boolean updateLastLoginActivityDate, Int32& status, String& password, Int32& passwordFormat, String& passwordSalt, Int32& failedPasswordAttemptCount, Int32& failedPasswordAnswerAttemptCount, Boolean& isApproved, DateTime& lastLoginDate, DateTime& lastActivityDate) +815 System.Web.Security.SqlMembershipProvider.CheckPassword(String username, String password, Boolean updateLastLoginActivityDate, Boolean failIfNotApproved, String& salt, Int32& passwordFormat) +105 System.Web.Security.SqlMembershipProvider.CheckPassword(String username, String password, Boolean updateLastLoginActivityDate, Boolean failIfNotApproved) +42 System.Web.Security.SqlMembershipProvider.ValidateUser(String username, String password) +78 System.Web.UI.WebControls.Login.AuthenticateUsingMembershipProvider(AuthenticateEventArgs e) +60 System.Web.UI.WebControls.Login.OnAuthenticate(AuthenticateEventArgs e) +119 System.Web.UI.WebControls.Login.AttemptLogin() +115 System.Web.UI.WebControls.Login.OnBubbleEvent(Object source, EventArgs e) +101 System.Web.UI.Control.RaiseBubbleEvent(Object source, EventArgs args) +37 System.Web.UI.WebControls.Button.OnCommand(CommandEventArgs e) +118 System.Web.UI.WebControls.Button.RaisePostBackEvent(String eventArgument) +166 System.Web.UI.WebControls.Button.System.Web.UI.IPostBackEventHandler.RaisePostBackEvent(String eventArgument) +10 System.Web.UI.Page.RaisePostBackEvent(IPostBackEventHandler sourceControl, String eventArgument) +13 System.Web.UI.Page.RaisePostBackEvent(NameValueCollection postData) +36 System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) +1565 -------------------------------------------------------------------------------- Version Information: Microsoft .NET Framework Version:2.0.50727.3053; ASP.NET Version:2.0.50727.3053 What could be the reason for such an error? How could I solve this?

  Read the article

• How can I automatically require a password when connecting to a WD MyBookLive?

  - by user-123

  I have created a user which has specific privileges to access the shares on our WD MyBookLive Network drive (ie it requires a password to connect), however after connecting once Windows seems to remember the password (or at least for the rest of the session). How can I make it so it is necessary to require a password every time the user connects to the drive or makes some change on Windows? I am particularly thinking of Cryptolocker and other variants of "ransomeware" which will try and connect to the drive and encrypt it.

  Read the article

• Computer hangs at BIOS screen. Cannot enter setup

  - by d2jxp

  I have an HP Pavilion a6500f (it's a year out of warranty) and it's hanging on the blue HP BIOS screen. If I mash F10 while it's starting up, it will say "Entering Setup..." but I will see no results. It will hang there and not do anything. If I actually wait until I can see the screen and then hit F10, there's no response at all and the computer will sit at the BIOS menu. I've dusted and cleaned it out, reseated the memory, switched the RAM slots, and reset the CMOS battery using the reset jumper. I'm out of ideas. I'm pretty sure it's not a hard drive issue, since my problem is at the BIOS. After this post, I'll disconnect the hard drive and try to just boot without it. Anyone have any other ideas? Edit: Okay, so I tried disconnecting the hard drive and now I can get back into the BIOS. I reconnected it and I'm locked out again. So the problem is my hard drive.. I guess I should delete this post unless someone has any ideas as to what's wrong with the drive?

  Read the article

• Will my RAID0 stay intact when I move it to a new computer?

  - by Jeremy H

  My primary drive is a 250GB WD SATA drive. So, I added 2x 500GB 7,200 RPM WD SATA drives into my Windows Vista box and created a 1TB RAID0. I then formatted the the primary drive and installed Windows 7. To my pleasant surprise when I booted into Windows 7 my RAID0 was still intact and I kept trotting along the same as I did before. Now I am replacing my motherboard, processor, and RAM and plan on formatting the primary 250GB drive again and using it to boot for a new clean install of Windows 7. My question is: if I move these two SATA drives which are setup for RAID0 into the new system, install Windows 7 again, will the RAID0 remain? Edit: Software RAID. I created it within Windows. The RAID0 does NOT contain the system boot partition.

  Read the article

• Computer hangs at BIOS screen. Cannot enter setup.

  - by d2jxp

  I have an HP Pavilion a6500f (it's a year out of warranty) and it's hanging on the blue HP BIOS screen. If I mash F10 while it's starting up, it will say "Entering Setup..." but I will see no results. It will hang there and not do anything. If I actually wait until I can see the screen and then hit F10, there's no response at all and the computer will sit at the BIOS menu. I've dusted and cleaned it out, reseated the memory, switched the RAM slots, and reset the CMOS battery using the reset jumper. I'm out of ideas. I'm pretty sure it's not a hard drive issue, since my problem is at the BIOS. After this post, I'll disconnect the hard drive and try to just boot without it. Anyone have any other ideas? Edit: Okay, so I tried disconnecting the hard drive and now I can get back into the BIOS. I reconnected it and I'm locked out again. So the problem is my hard drive.. I guess I should delete this post unless someone has any ideas as to what's wrong with the drive?

  Read the article

< Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >