Search Results

Search found 4708 results on 189 pages for 'hot deploy'.

Page 75/189 | < Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >

• My fingers are cold when using my computer - solutions?

  - by Kjensen

  This might seem silly, and if there is no good and practical solution... I will live. I am a programmer and sit at a computer 10 hours a day - and even though the rest of me is nice and warm (at least warm), my fingers are cold as ice. Are there some gadgets or tricks to keep your fingers warm while typing/mousing? Gloves do not seem like a good solution, since it hinders the movement of the fingers. I have sometimes put my extra laptop next to the mouse pad, so that it vents hot air on the mouse - and that works... But it is not very practical, plus it only works for one hand (and not very well). Tips?

  Read the article

• Dell PowerEdge 6850 Degraded HDD

  - by Matt

  Good Morning, We have a dell power edge 6850 with a degraded drive in the RAID array. I have never had to recover such an issue, so any help or advice would be welcome. Basically it hasn't affected the server at an operating system level, but has slowed down performance, I have a replacement drive in hand but as this is our main database server I want to proceed with extreme caution. My options as I see them are - Can I just hot swap the degraded drive with the new one and the data will automatically re-sync and we are all back to normal presumably this is dependant on the current raid configuration? reading various comments on-line I may need to re-configure the RAID array and re-build the broken drive? This screams disaster to me with the main worry being that I wipe any other data. Option 1 would of course make my day. Thanks in advance

  Read the article

• Network Server Cabinets - How does the ventilation work?

  - by Nicholas

  Recently I've been looking at a range of network server cabinets with a mesh door at the rear. At the top of the cabinet are ceiling mounted fans with dust filters attached. These fans suck air out of the cabinet - presumably to remove the hot air that has risen to the top. My question is why do these fans have dust filters? What point do they serve? If the air flow is pulled in by these fans through the mesh door, then surely they are not there to protect the hardware inside from dust? Also, there are other minor grilled gaps around the enclosure, how does this kind of ventilation design work?

  Read the article

• Are some DSL modems cheaper to operate than others? (power usage question)

  - by SetJmp

  I recently have started using a Motorola 2210 in conjunction with AT&T's DSL service in the Silicon Valley area. That gadget runs hot to the touch! Which means... I assume it is gobbling lots of electricity even when I am not using it. Has anyone studied this subject in a rigorous way? Which leads to the question... if the 2210 is very energy inefficient are some DSL modem models cheaper to operate than others? -SetJmp

  Read the article

• How does one go about fixing a pixelation issue?

  - by Tyler

  I've been having a lot of trouble with pixelation and also in-game display driver crashes. At first I thought the problem may have been my graphics card (Sapphire 5750) but I have RMA'd it three times and I'm still having trouble. So what I think it might be is my PSU, its 650Watt but its made by Azza so it was cheap and not made by a necessarily good company. Or maybe it could be the CPU (AMD Phenom Black Edition 3.4Ghz) It runs hot (60C) but it passes Everest's test. Someone told me it could be the memory (8GB DDR3) but I don't really see how RAM has anything to do with my problem. So what are some of you suggestions? Here is a video a made awhile ago of what is happening. http://www.metacafe.com/watch/4392213/ati_radeon_5750/ That was just a stress test most games tend to just freeze and crash or lock my system up.

  Read the article

• Windows 7 on 1st Gen MacbookPro Unibody (Q4-2008) - power problems.

  - by typemismatch

  I have the first generation macbook pro, purchased Q4 2008. I've been trying to run Windows 7 and can get it all installed great with the BootCamp 3.1 64 bit drivers however ... power management isn't great. The screen and keyboard don't automatically dim - the laptop gets too hot. I noticed on some newer macbook pros that windows 7 works perfectly and the above doesn't happen. Does anyone know if there really is a hardware issue with this 1st gen or is there some firmware update I can use to fix this? Thanks!

  Read the article

• Is it dangerous to add/remove a hard-drive to a Windows machine which is in stand by?

  - by Adal

  Can I add a SATA drive to a Windows 7 machine which is in standby mode? The hardware supports hot-plug. Could pulling the drive out while in standby corrupt the data on the drive (unflushed caches, ...)? Does Windows flush before standing by? How about swapping a drive with another drive of different kind (SSD - mechanical disk) and size, also while in stand-by. Could the OS when waking up believe that the old drive is still there, and write to it and thus corrupt it, since the new one has different partitions and data?

  Read the article

• My Mac Book Pro is turning itself, on my bagpack

  - by J. Pablo Fernández

  This happens to me twice: I press the power button on my Mac Book Pro, I choose sleep, I close it, I unplug everything, I confirm that is off (by pressing my ear to it) and put it in my back. Some minutes latter it wakes up by itself. Both times I caught it in time, well, the second time it was so hot I couldn't touch some parts and it was refusing to actually wake up, the screen was blank. Restarting it worked though. Any ideas what might be going on and/or how to prevent this?

  Read the article

• Xen find VBD id for physical disks

  - by Joe

  I'm starting a xen domU using xm create config.cfg. Within the config file are a number of physical block devices (LVs) which are added to the guest and can be accessed fine when it boots. However, at a point in the future I need to be able to hot unplug one of these disks using the xm block-detach command. This command, however, requires the vbd id of the device to be detached and I can't find a way to find the device id for a particular disk 'plugged in' at start up. Any help is much appreciated!

  Read the article

• My fingers are cold when using my computer - solutions?

  - by Kjensen

  I am a programmer and sit at a computer ten hours a day - and even though the rest of me is nice and warm, my fingers are as cold as ice. Are there any gadgets or tricks to keep your fingers warm while typing/mousing? Gloves do not seem like a good solution, since it hinders the movement of the fingers. I have sometimes put my extra laptop next to the mouse pad so that it vents hot air on the mouse - and that works. However it is not very practical, plus it only works for one hand (and not very well).

  Read the article

• Fresh install of Xenserver 6.2 , cannot load tools in Guest Win7

  - by Erik

  I've just started testing the XenServer 6.2 offering.. it's awesome so far.. I've event loaded all the patches and hot fixes, and started a windows 7 guest image. I want to install tools, but whenever I click the install tools boxes.. I'm taken to my VM console and nothing loads. It's a brand new guest, and most of the advice is for those with previous versions of tools loaded. Any ideas how to fix this?

  Read the article

• Little server for a little network: Asus TS Mini + Windows Home Server or other?

  - by microspino

  Hello, I'm building a little network with 4 computer a plotter, 3 printers an a HP Fax/Scan/Copy/Print machine. The network is connected to the web by a D-Link router/firewall. I would like to add little server to have file sharing (reachable via VPN from outside by a single user-road-warrior), automatic backups. I would like to avoid big electrics bills or, to say It in a green way, I would like to avoid useless power consumption made by a big server with hot-plug, Raid, double PSU because I don't need all this stuff. The server must work 24/7 and the budget is between 400€ and 1000€. I'm evaluating the Asus EEE Box (with XP), a TranquilPC (with XP), a FitPC (again with XP), and an Asus TS Mini (with Windows Home Server). I like the latter but since I'm Europe I don't know where I can buy It. Do you have any suggestion/experience to share with me about: which hardware do I have to buy ? which O.S. ?

  Read the article

• RAID setup for maximizing data retention and read speed

  - by cat pants

  My goals are simple: maximize data retention safety, and maximize read speeds. My first instinct is to do a a three drive software RAID 1. I have only used fakeraid RAID 1 in the past and it was terrible (would have led to data loss actually if it weren't for backups) Would you say software raid 1 or a cheap actual hardware raid card? OS will be linux. Could I start with a two drive raid 1 and add a third drive on the fly? Can I hot swap? Can I pull one of the drives and throw it into a new machine and be able to read all the data? I do not want a situation where I have a raid card fail and have to try and find the same chipset in order to read my data (which i am assuming can happen) Please clarify any points on which it sounds like I have no idea what I am talking about, as I am admittedly inexperienced here. (My hardest lesson was fakeraid lol) Thanks!

  Read the article

• My 386sx refuses to start in cold days

  - by Armadillo

  My old computer refuses to start in cold days. So, in really hot days (about 40ºC / 104ºF ) or even hotter, this PC usually starts, but in cold days, it wont. When the temperature is not in the "sweet-spot" the power light turns on for an half a second and then the computer turns off. But when it's really cold, not even the power light turns on, nor even a blink. Sometimes I use an Hair dryer, pointed directly to the PSU and that works great. 5 to 10 minutes is enough, depending on the ambient temperature. I think something is going wrong in my AT power supply. I can't replace this PSU for another because it has a non-standard size and connectors to power the motherboard. Does anybody have a clue about what it's failing in my PSU, so I can change that component (resistor, capacitor, ??, etc) and rock on with my 80386? Thanks

  Read the article

• HP DL380 G5 Predictive failure of a new drive

  - by CharlieJ

  Consolidated Error Report: Controller: Smart Array P400 in slot 3 Device: Physical Drive 1I:1:1 Message: Predictive failure. We have an HP DL380 G5 server with two 72GB 15k SAS drives configured in RAID1. A couple weeks ago, the server reported a drive failure on Drive 1. We replaced the drive with a brand new HDD -- same spares number. A few days ago, the server started reporting a predictive drive failure on the new drive, in the same bay. Is it likely the new drive is bad... or more likely we have a bay failure problem? This is a production server, so any advice would be appreciated. I have another spare drive, so I can hot swap it if this is a fluke and new drive is just bad. THANKS! CharlieJ

  Read the article

• How can I view my video card's temperature via SSH?

  - by NT3RP

  I've finally managed to set up my two ATI Radeon 6950 video cards in my machine, but the cards can get quite hot. Based on the arrangement of my apartment, I want to be able to SSH into the machine an execute a command to find out the temperature. What I have tried so far is this... export DISPLAY=:0.0 sudo aticonfig --adapter=0 --od-gettemperature However, when I do that via SSH, I get the following error: ERROR - X needs to be running to perform ATI Overdrive(TM) commands If I turn on X forwarding when I remote into the machine, then it just seems to affect my local machine instead of the remote machine. Am I doing this correctly? Is there a better way to monitor my video card's temperature?

  Read the article

• How can I deactivate the gnome desktop of my ubuntu server?

  - by 19 Lee

  I'm running a home server on my old laptop (atom cpu). I installed ubuntu 12.04 server edition, but I also installed ubuntu-desktop. So, when I turn it on, ubuntu desktop is shown. I sometimes use GUI, but I want to turn the ubuntu-desktop (gnome-desktop) off when I don't use it. I think I can save resources by turning off the GUI. It's necessary since my laptop's performance is not very good and it often becomes very hot. I guess I can run ubuntu-desktop on my terminal with "startx" command. But, I don't know how to turn the X window off for a moment. Anybody have an idea? Thanks in advance.

  Read the article

• HP Pavillion dv6 laptop - 15 beeps on startup and a black screen?

  - by dunc

  Usual story - girlfriend's step-brother's laptop is broken. I don't know a huge amount about what occurred before it broke, but I do know the following: When you try to turn the laptop on, it beeps 15 times exactly. The screen remains black. The LED on the Caps Lock key flashes continuously. If left on, the laptop never boots - as far as I can see. If left on, on a stable surface with decent ventilation for a relatively short period of time, the laptop (below keyboard, but not where the RAM/HDD are) gets very hot. I've tried doing what most websites appear to recommend for similar problems, which is to disconnect AC and battery then hold the power button down for a minute before reconnecting the AC and trying to turn the laptop on - no difference. EDIT I've also tried re-seating the RAM, to no avail. Any ideas? Thanks in advance,

  Read the article

• ruby on rails server is intermittently slow

  - by Richard

  My rails installation was chugging along nicely. Last night we had to perform a hot-patch with was really a standard deploy of some exception code. Once capistrano finished the operation one of our admins discovered that there were two long running passenger processes. While we have deployed release over the past two weeks it would appear that these processes have been here and alive the whole time. Granted they could have been zombies or any other artifact and at this point we do not know what state they were in. Which leads me to the question: There are so many moving parts between the rails application and the OS/hardware that being a SME is probably no longer possible. So; how does a sysadmin perform root-cause analysis with any certainty? And: When do I just start rebooting servers?

  Read the article

• scsi and ata entries for same hard drive under /dev/disk/by-id

  - by John Dibling

  I am trying to set up a ZFS pool using 4 bare drives which I have attached to my Ubuntu system via a SATA hot swap backplane. These are Hitachi SATA drives. When I list the contents of /dev/disk/by-id, I see two entries for each drive: root@scorpius:/dev/disk/by-id# ls | grep Hitachi ata-Hitachi_HDS5C3030ALA630_MJ1323YNG0ZJ7C ata-Hitachi_HDS5C3030ALA630_MJ1323YNG1064C ata-Hitachi_HDS5C3030ALA630_MJ1323YNG190AC ata-Hitachi_HDS5C3030ALA630_MJ1323YNG1DGPC scsi-SATA_Hitachi_HDS5C30_MJ1323YNG0ZJ7C scsi-SATA_Hitachi_HDS5C30_MJ1323YNG1064C scsi-SATA_Hitachi_HDS5C30_MJ1323YNG190AC scsi-SATA_Hitachi_HDS5C30_MJ1323YNG1DGPC I know these are the same drives because I wrote down the serial numbers, and all the other drives in this system are either Seagate or WD. The serial number for the first one, for example, is YNG0ZJ7C. Why are there two entries here for each drive? More to the point, when I create my ZFS pool which one should I use; the scsi- one or the ata- one?

  Read the article

• Let a program (called by other program) run as admin without prompt

  - by DarkGhostHunter

  As you may know, Steam doesn't like no-admin accounts for installing games or whatsoever. In my case, I have a user in my computer that usually install a lot of games and every time I have to put my password to successfully play them. Blame, /bin/SteamService.exe. I came up with a solution: using RunAs to make Steam run as the admin user. But that is a potential security risk. So instead of that, I'm asking if is possible to do the following: Hot to run SteamService.exe with high trust levels (or admin privileges) automatically when Steam calls it? That way he can play and install games in Steam leaving the rest of the system alone. I don't mind if the user has to click "yes or no", but without prompt its better because some games asks every time they're executed.

  Read the article

• Disk controller speed responsible for slow write speeds?

  - by vizvayu

  I have question. I'm using ESXi 4.0U1 in an IBM x3200M2 with an integrated LSI 1064e RAID controller, without any kind of cache. I have 3 250GB HOT-SWAP SATA HDs configured in RAID1E (IME). ESXi works fine, read speed are quite OK, but write speeds are incredible slow, never more than 8MB/s, and this is the best case scenario, benchmarking with iozone streaming writes, using a VMWare Paravirtual controller and with only this VM active, no swapping of any kind (total vm memory reserved). Already wrote to IBM but I don't have any kind of pay support so they didn't even answered, so I'm just wondering... anybody has any experience with a similar setup? I just want to be sure this is hardware related and can't be fixed with some kind of config option, because I'm thinking on buying a new RAID controller (Adaptec 2405 looks nice). Thanks again!

  Read the article

• Linux virtual disk stripping or multi-path samba share?

  - by wachpwnski

  I am trying to build a file storage box for media. It needs to span two or more directories or partitions as one share. There are a few solutions but reasons why I want to avoid them, among these are: Using LVM2 for stripping. I don't really have the resources to back up everything on the volumes incase one HDD goes south. I would end up loosing everything. Maybe there is a better option for this to prevent data loss with hot swappable drives or some kind of raid. Using symbolic links in the share. This will get tedious every time a new sub-directory is added. Is there some kind of software raid I can use to merge two directories virtually? I am aware of the issue where /dev/hda1/media/file.1 and /dev/hdb1/media/file.1 both exist. But I'm sure there are some creative solutions for this.

  Read the article

• Should I bother upgrading my Opteron 270 Server?

  - by MousePad

  I have an Opteron Server machine (in a large workstation class case) running on the Tyan 2895 motherboard. It's a dual CPU socket board, but I only have one 270 in there. I have 4GB of RAM, but less than 3GB is addressable, even in 64bit mode, due to the way the board is designed. Is it worth spending a few hundred on an additional CPU and maybe some more RAM? The other problem is that one of the two SATA ports on the board had its wire socket break off. So only one drive can be run as of now. I could have it repaired, but at what cost? Add in the fact that the power supply is gunked up with dust and it's a bit of a nightmare. I actually work about it getting too hot. Seems that for the money I could buy a new server rack from Dell, but it also seems a shame to waste an otherwise working, and for my needs still very fast machine.

  Read the article

• Ubuntu stops auto-mounting flash drive

  - by Brian

  It seems that after being up for a few days, my Ubuntu system refuses to auto-mount hot-plugged USB disks (i.e. flash drives). The output from dmesg shows that the kernel recognizes the device correctly. The only solution I'm aware of at the moment is to reboot (logging out may work as well, but the impact is the same since I have a bunch of stuff open and it takes a few minutes to get everything situated after startup/login). I thought gvfs-fuse-daemon was the thing responsible for managing filesystems in userspace, but killing and restarting that doesn't help. Any other ideas?

  Read the article

< Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >