Search Results

Search found 12645 results on 506 pages for 'maintenance mode'.

Page 75/506 | < Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >

• SQL Server Database Settings

  - by rbishop

  For those using Data Relationship Management on Oracle DB this does not apply, but for those using Microsoft SQL Server it is highly recommended that you run with Snapshot Isolation Mode. The Data Governance module will not function correctly without this mode enabled. All new Data Relationship Management repositories are created with this mode enabled by default. This mode makes SQL Server (2005+) behave more like Oracle DB where readers simply see older versions of rows while a write is in progress, instead of readers being blocked by locks while a write takes place. Many common sources of deadlocks are eliminated. For example, if one user starts a 5 minute transaction updating half the rows in a table, without snapshot isolation everyone else reading the table will be blocked waiting. With snapshot isolation, they will see the rows as they were before the write transaction started. Conversely, if the readers had started first, the writer won't be stuck waiting for them to finish reading... the writes can begin immediately without affecting the current transactions. To make this change, make sure no one is using the target database (eg: put it into single-user mode), then run these commands: ALTER DATABASE [DB] SET ALLOW_SNAPSHOT_ISOLATION ONALTER DATABASE [DB] SET READ_COMMITTED_SNAPSHOT ON Please make sure you coordinate with your DBA team to ensure tempdb is appropriately setup to support snapshot isolation mode, as the extra row versions are stored in tempdb until the transactions are committed. Let me take this opportunity to extremely strongly highly recommend that you use solid state storage for your databases with appropriate iSCSI, FiberChannel, or SAN bandwidth. The performance gains are significant and there is no excuse for not using 100% solid state storage in 2013. Actually unless you need to store petabytes of archival data, there is no excuse for using hard drives in any systems, whether laptops, desktops, application servers, or database servers. The productivity benefits alone are tremendous, not to mention power consumption, heat, etc.

  Read the article

• Turn O&M Operations into Optimized Projects with Oracle Primavera

  - by mark.kromer

  Oracle enterprise project portfolio management with Primavera is much more than optimizing project performance and eliminating project failure on new projects, capital programs, etc. A very common use case that we see is small-scale frequent and recurring projects based on on-going operations and maintenance. As opposed to assigning resources to various activities when you are building a new network infrastructure, for example, Oracle has teamed-up the Primavera and eBusiness Suite teams to provide direct integration for work orders from Oracle's Enterprise Asset Management (eAM) system to populate into Primavera P6 project schedules. So now that your network infrastructure build-out project is complete, planners and operations managers can use the world-class what-if and scheduling capabilities in Primavera tools to assign work orders, maximize resource utilization and to reuse templates for typical O&M operations in Primavera and share that back to the operations teams using eAM for maintenance. Also, large-scale maintenance operations related to large assets in the asset lifecycle will include phase-outs, shutdowns and turn-arounds which are classic maintenance projects, as opposed to building something new, that Oracle Primavera with Oracle e-Business Suite provides full coverage to optimize your ALM processes in your business. Read more about these new capabilities from Oracle in the ERP space from the Oracle eAM data sheet.

  Read the article

• 2 questions. IDO mode not caching properly / forcing buffers to named windows.

  - by user112043

  1 My ido mode does not properly cache filenames / folders. It will list files inside a folder, but from a while ago without any of the newer files showing. Any suggestions ? 2 In jde, when I have multiple windows open, compiling on one window will create a corresponding "* name of the class *" that will open on the next window in order. This is fine if I only have one window open but can I get some help writing a function that I could use to : Name a window Force all buffers of JDE compile server to only ever open in that window if it exists Force all run windows from jde in the form of * name of the class * to open in the same window if it exists. Jde automatically names the buffer " * name of the class * ", I will probably dig around the codes to find an easy fix for that... so if the code could just force all windows using a regexp containing * jde run - filename * or something along the lines would also work. Thanks for your help, first post here as well. I really would like just some ideas on what may be going wrong with 1, 2 if anyone is feeling kind.

  Read the article

• Why are changes to coffeescript files not being compiled when my Rails 3.2.0 app is in development mode?

  - by ben

  Normally, any changes I make to .js.coffee files in my Rails 3.2.0 app in development mode take effect when I refresh the page. All of a sudden, this is not happening. If I do rake assets:precompile, then the changes are shown, but then if I do rake assets:clean they go back to not being shown. What is causing this? Edit: Restarting the server makes the changes show. Why isn't this happening automatically as before? Edit: Here is my development.rb Myapp::Application.configure do # Settings specified here will take precedence over those in config/application.rb # In the development environment your application's code is reloaded on # every request. This slows down response time but is perfect for development # since you don't have to restart the web server when you make code changes. config.cache_classes = false # Log error messages when you accidentally call methods on nil. config.whiny_nils = true # Show full error reports and disable caching config.consider_all_requests_local = true config.action_controller.perform_caching = false # Don't care if the mailer can't send config.action_mailer.raise_delivery_errors = false # Print deprecation notices to the Rails logger config.active_support.deprecation = :log # Only use best-standards-support built into browsers config.action_dispatch.best_standards_support = :builtin # Raise exception on mass assignment protection for Active Record models config.active_record.mass_assignment_sanitizer = :strict # Log the query plan for queries taking more than this (works # with SQLite, MySQL, and PostgreSQL) config.active_record.auto_explain_threshold_in_seconds = 0.5 # Do not compress assets config.assets.compress = false # Expands the lines which load the assets config.assets.debug = true config.action_mailer.default_url_options = { :host => 'localhost:3000' } config.log_level = :warn end

  Read the article

• How to use HSQLDB in Oracle query syntax mode?

  - by Jan Algermissen

  I am trying to use HSQLDB as an embedded database in a spring application (for testing). As the target production database is Oracle, I would like to use HSQLDBs Oracle syntax mode feature. In the Spring config I use <jdbc:embedded-database type="HSQL" id="dataSource"> </jdbc:embedded-database> <jdbc:initialize-database data-source="dataSource" enabled="true"> <jdbc:script location="classpath:schema.sql"/> </jdbc:initialize-database> And in schema.sql at the top I wrote: SET DATABASE SQL SYNTAX ORA TRUE; However, when running my test, I get the following error: java.sql.SQLException: Unexpected token: DATABASE in statement [SET DATABASE SQL SYNTAX ORA TRUE] Is this a syntax error or a permissions error or something entirely different? Thanks - also for any pointers that might lead to the answer. Given that HSQL is the Spring default for jdbc:embedded-database and given the target is Oracle, this scenario should actually be very common. However, I found nothing on the Web even touching the issue.

  Read the article

• What would it take to get auto-revert-mode to actually work in my dired buffer?

  - by Cheeso

  Apparently auto-revert-mode is supposed to work in dired buffers. I had never heard of this, but the doc says it works. Then I read a little more and found some fine print: Auto-reverting Dired buffers currently works on GNU or Unix style operating systems. It may not work satisfactorily on some other systems. ...and... [dired buffers] do not auto-revert when information about a particular file changes (e.g. when the size changes) or when inserted subdirectories change. To be sure that all listed information is up to date, you have to manually revert using g, even if auto-reverting is enabled in the Dired buffer. source Well, uh, gee.... That doesn't sound like autorevert to me. What would it take to get auto-revert for dired to actually work? Even on (gasp) non-Unix operating systems. Could I just modify auto-revert-handler to call revert-buffer on dired buffers?

  Read the article

• How do I run NUnit in debug mode from Visual Studio?

  - by Jon Cage

  I've recently been building a test framework for a bit of C# I've been working on. I have NUnit set up and a new project within my workspace to test the component. All works well if I load up my unit tests from Nunit (v2.4), but I've got to the point where it would be really useful to run in debug mode and set some break points. I've tried the suggestions from several guides which all suggest changing the 'Debug' properties of the test project: Start external program: C:\Program Files\NUnit 2.4.8\bin\nunit-console.exe Command line arguments: /assembly: <full-path-to-solution>\TestDSP\bin\Debug\TestDSP.dll I'm using the console version there, but have tried the calling the GUI as well. Both give me the same error when I try and start debugging: Cannot start test project 'TestDSP' because the project does not contain any tests. Is this because I normally load \DSP.nunit into the Nunit GUI and that's where the tests are held? I'm beginning to think the problem may be that VS wants to run it's own test framework and that's why it's failing to find the NUnit tests? [Edit] To those asking about test fixtures, one of my .cs files in the TestDSP project looks roughly like this: namespace Some.TestNamespace { // Testing framework includes using NUnit.Framework; [TestFixture] public class FirFilterTest { /// <summary> /// Tests that a FirFilter can be created /// </summary> [Test] public void Test01_ConstructorTest() { ...some tests... } } } ...I'm pretty new to C# and the Nunit test framework so it's entirely possible I've missed some crucial bit of information ;-) [FINAL SOLUTION] The big problem was the project I'd used. If you pick: Other Languages->Visual C#->Test->Test Project ...when you're choosing the project type, Visual Studio will try and use it's own testing framework as far as I can tell. You should pick a normal c# class library project instead and then the instructions in my selected answer will work.

  Read the article

• Run Reporting Service in local mode and generate columns automatically?

  - by grady

  Hi, I have a SQL query right now which I want to use with the MS reporting services in my ASP.NET application. So I created a report in local mode (rdlc) and attached this to a report viewer. Since my query uses parameters, I created a stored procedure, which had exactly those parameters. In addition to that I had some textboxes which are used for entering the params for the query and a button to call the stored proc and to fill the datatset which is bound to the report viewer. This works, I press the button and according to what I entred the correct data is shown. Now my question: In the future I plan to have multiple reports (which will be selected in a dropdown) and I wonder if I can somehow just call the correct stored procedure and according to the columns which are *SELECT*ed in the procedure, the columns are shown in the report. Example: I select report1 from the dropdown (procedure for report 1 is called), 5 columns are shown in the reportviewer. I select report2 from dropdown (procedure for report 2 is called), 8 columns are shown. Is that possible somehow? Thanks :-)

  Read the article

• Why do my debugger randomly jump out of debug mode?

  - by Clean

  Hi, I'm experiencing a very annoying behavior with the debugger in Visual Studio 2008 Professional. I'm debugging a ASP.NET web application, and when stepping through the code the debugger randomly "jumps out" of debug mode, but without the debugger stopping. So when I'm stepping through my code like this: step over, step over, step over, step over, ... , step over The debugger continues as If I was pressing Continue, like this: step over, step over, step over, step over, ... , continue Thing is, I never touch continue! So, the debugger is still running, the ASP.NET page renders, but my "stepping" ends. This is of course very annoying. And it happens totally randomly. Before switching to Windows 7 and IIS 7.5, I've never experienced this problem. My colleague who debugs the exact same code, but on a Windows XP machine running IIS 6 have never had this problem either. So my thought is, perhaps this is Windows 7 or IIS 7.5 related? I've already made sure <compilation defaultLanguage="c#" debug="true" /> is set in web.config. Have anyone experienced the same problem, or perhaps have an idea why I'm experiencing this annoying behavior? Thanx! P.S I realize this question might be more Visual Studio 2008 specific rather than programming specific, but I figure my best chance to find somebody that experienced the same problem would be at a forum for programmers (since naturally, programmers are the most frequent users of Visual Studio 2008).

  Read the article

• Creating a new window that stays on top even when in full screen mode (Qt on Linux)

  - by Lorenz03Tx

  I'm using Qt 4.6.3, and ubuntu linux on an embedded target. I call dlg->setWindowState(Qt::WindowFullScreen); on my windows in my application (so I don't loose any real-estate on the touch screen to task bar and status panel on the top and bottom of the screen. This all works fine and as expected. The issue comes in when I want to popup the on screen keyboard to allow the user to input some data. I use m_keyProc= new QProcess(); m_keyProc->start("onboard -s 640x120"); This pops up the keyboard but it is behind the full screen window. The onbaord keyboards preferences are set such that it is always on top, but that seems to actually mean "except for full screen windows". I guess that makes sense and probably meets most use cases, but I need it to be really on top. Can I either A) Not be full screen mode (so the keyboard works) and programmatically hide the task bars? or B) Force the keyboard to be on top despite my full screen status? Note: On windows we call m_keyProc->start("C:\\Windows\\system32\\osk.exe"); and the osk keyboard is on top despite the full screen status. So, I'm guessing this is a difference in window mangers on the different operating systems. So do I need to set some flag on the window with the linux window manager?

  Read the article

• How to Prompt user with permission dialog in iframe application

  - by ibrahimkhan

  Hi, I am using Facebook.showPermissionDialog("read_stream,publish_stream, offline_access, email") to show permission dialog. Its working in FBML mode but the problem is in IFRAME mode. The below code also works fine in FBML mode but not in Iframe mode. fb:prompt-permission perms="read_stream,publish_stream, offline_access, email"Allow Access? Please help me regarding this.. I need to display Prompt permission dialog in IFRAME mode Thanks in advance, Ibrahim.

  Read the article

• String.substring(index) has stoped my thread in debug mode.

  - by Arkaha

  Hello! I work with j2me polish 2.0.7, in eclipse 3.4.2, with wtk2.5.2_01. I create control which draws text: normal, bold, and italic. The code below is parsing raw text, and search for * and _ symbols, if found than add to draw vector the text and the drawer, and it's just stops after getting second time to the line 58: String test = new String(raw_text_buff.substring(iter)); it stops in raw_text_buff.substring(iter), ONLY in debug mode.. raw text is: bla bla bla *1000* bla bla Full code: private String raw_text = "bla bla bla *1000* bla bla"; Vector draw_items = null; private void prepareText() { char open_char = 0; int open_pos = 0; Object []param = null; StringBuffer sb = new StringBuffer(); String raw_text_buff = new String(raw_text); int iter = 0; boolean was_reset = false; while(true) { char c = raw_text_buff.charAt(iter); if(iter == raw_text_buff.length() || c == '*' || c == '_') { if(sb.length() > 0) { BmFont viewer = null; String str = sb.toString(); if(open_char == '*' && null != bm_strong) { viewer = bm_strong.getViewer(str); }else if(open_char == '_' && null != bm_italic) { viewer = bm_italic.getViewer(str); }else if(null != bm_normal) { viewer = bm_normal.getViewer(str); }else { } param = new Object[2]; param[0] = str; param[1] = viewer; if(null == draw_items) draw_items = new Vector(); draw_items.addElement(param); sb = new StringBuffer(); if(open_char == 0 && (c == '*' || c=='_')) open_char = c; else open_char = 0; String test = new String(raw_text_buff.substring(iter)); // stucks here. raw_text_buff = test; iter = 0; was_reset = true; }else { open_char = c; } if(iter == raw_text_buff.length()) break; }else { sb.append(c); } ++iter; } } What I'm doing wrong?

  Read the article

• SQL Server connection help...

  - by Gopal

  Using SQL Server 2005 I have the server connection name as (server1) in windows authentication mode, I want to change windows authentication mode to sql server authentication mode... when i try to change sql server authentication mode with username = sa & password = sa, it showing error... How to change the authentication mode or how to create a new sql connection?

  Read the article

• Hide the Emacs echo area when not in use

  - by Baldur

  The echo area is the line at the bottom of Emacs below the mode line: ~ ~ | | +-----------------------+ |-U:--- mode-line | +-----------------------+ | M-x echo-area | +-----------------------+ Now the mode line is highly customizable while the echo area is more rigid (and unused a lot of the time). The question is pretty simple: is it possible to hide the echo area during inactivity and redisplay it once it needs your attention: ~ ~ ~ ~ | | | | | | +-----------------------+ | | |-U:--- mode-line | +-----------------------+ +-----------------------+ |-U:--- mode-line | | M-x echo-area | +-----------------------+ +-----------------------+ Inactive Active This is similar to the way Google Chrome displays URLs when you hover your mose over a link and the Firefox addon Pentadactyl where the command-line is hidden by default.

  Read the article

• Automount of external hard disk

  - by moose

  I have an Intenso 6002560 1TB Memory Station - an external hard disk. This hard disk gets connected via Y-USB cable. When I connect both USB-ends to my Notebook, it gets recognized by my Ubuntu 10.04.4 LTS system: moose@pc07:~$ lsusb [...] Bus 002 Device 005: ID 13fd:1840 Initio Corporation [...] and Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00065e10 Device Boot Start End Blocks Id System /dev/sda1 * 1 37810 303704064 83 Linux /dev/sda2 37810 38914 8864769 5 Extended /dev/sda5 37810 38914 8864768 82 Linux swap / Solaris Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0d6ea32a Device Boot Start End Blocks Id System /dev/sdc1 1 121601 976759008+ c W95 FAT32 (LBA) But it did not get mounted: moose@pc07:/dev$ mount -l /dev/sda1 on / type ext4 (rw,errors=remount-ro,user_xattr) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/moose/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=moose) However, I could mount it manually with mount -t vfat /dev/sdc1 /mnt/sdc1 as you can see here: moose@pc07:~$ mount -l /dev/sda1 on / type ext4 (rw,errors=remount-ro,user_xattr) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/moose/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=moose) /dev/sdc1 on /mnt/sdc1 type vfat (rw) edit: Another command: moose@pc07:~$ sudo blkid -o list device fs_type label mount point UUID ---------------------------------------------------------------------------------------------------------------------- /dev/sda1 ext4 / 45eb611b-517e-425b-8057-0391726cccd5 /dev/sda5 swap <swap> e9dc42f3-594c-4b62-874a-305eda5eed41 moose@pc07:~$ blkid -o list device fs_type label mount point UUID ---------------------------------------------------------------------------------------------------------------------- /dev/sda1 ext4 / 45eb611b-517e-425b-8057-0391726cccd5 /dev/sda5 swap <swap> e9dc42f3-594c-4b62-874a-305eda5eed41 /dev/sdc1 /mnt/sdc1 edit: another command: moose@pc07:~$ ls -l /dev/disk/by-uuid/ total 0 lrwxrwxrwx 1 root root 10 2012-09-30 09:31 45eb611b-517e-425b-8057-0391726cccd5 -> ../../sda1 lrwxrwxrwx 1 root root 10 2012-09-30 09:31 e9dc42f3-594c-4b62-874a-305eda5eed41 -> ../../sda5 Here is a link to a Launchpad question about this problem. But I would like it to mount automatically. What do I have to do?

  Read the article

• Using Oracle Linux iSCSI targets with Oracle VM

  - by wim.coekaerts

  A few days ago I had written a blog entry on how to use Oracle Solaris 10 (in my case), ZFS and the iSCSI target feature in Oracle Solaris to create a set of devices exported to my Oracle VM server. Oracle Linux can do this as well and I wanted to make sure I also tried out how to do this on Oracle Linux and here are the results. When you install Oracle Linux 5 update 5 (anything newer than update 3), it comes with an rpm called scsi-target-utils. To begin your quest, should you choose to accept it :) make sure this is installed. rpm -qa |grep scsi-target If it is not installed : up2date scsi-target-utils The target utils come with a tool tgtadm which is similar to iscsitadm on Oracle Solaris. There are 2 components again on the iSCSI server side. (1) create volumes - we will use lvm with lvcreate (2) expose a target using tgtadm. My server has a simple setup. All the disks are part of a single volume group called vgroot. To export a 50Gb volume I just create a new volume : lvcreate -L 50G -nmytest1 vgroot This will show up as a new volume in /dev/mapper as /dev/mapper/vgroot-mytest1. Create as many as you want for your environment. Since I already have my blog entry about the 5 volumes, I am not going to repeat the whole thing. You can just go look at the previous blog entry. Now that we have created the volume, we need to use tgtadm to set it up : make sure the service is running : /etc/init.d/tgtd start or service tgtd start (if you want to keep it running you can do chkconfig tgtd on to start it automatically at boottime) Next you need a targetname to set everything up. My recommendation would be to install iscsi-initiator-utils . This will create an iscsi id and put it in /etc/iscsi/initiatorname.iscsi. For convenience you can do : source /etc/iscsi/initiatorname.iscsi echo $InitiatorName and from here on use $InitiatorName instead of the long complex iqn. create your target : tgtadm --lld iscsi --op new --mode target --tid 1 -T $InitiatorName to show the status : tgtadm --lld iscsi --op show --mode target add the volume previously created : tgtadm --lld iscsi --op new --mode logicalunit --tid 1 --lun 1 -b /dev/mapper/vgroot-mytest1 re-run status to see it's there : tgtadm --lld iscsi --op show --mode target and just like on Oracle Solaris you now have to export (bind) it : tgtadm --lld iscsi --op bind --mode target --tid 1 -I iqn.1986-03.com.sun:01:2a7526f0ffff If you want to export the lun to every iscsi initiator then replace the iqn with ALL. Of course you have to add the iqn of each iscsi initiator or client you want to connect. In the case of my 2 node Oracle VM server setup, both Oracle VM server's initiator names would have to be added. use status again to see that it has this iqn under ACL tgtadm --lld iscsi --op show --mode target You can drop the --lld iscsi if you want, or alias it. It just makes the command line more obvious as to what you are doing. Oracle VM side : Refer back to the previous blog entry for the detailed setup of my Oracle VM server volumes but the exact same commands will be used there. discover : iscsiadm --mode discovery --type sendtargets --portal login : iscsiadm --mode node --targetname iscsi targetname --portal --login get devices : /etc/init.d/iscsi restart and voila you should be in business. have fun.

  Read the article

• "previousMode": Controling the Pin Action of a TopComponent

  - by Geertjan

  An excellent thing I learned today is that you, as a developer of a NetBeans module or NetBeans Platform application, can control the pin button. Up until today, whenever I had a TopComponent defined to appear in "rightSlidingSide" mode and then I clicked the "pin" button, as shown here... ...the TopComponent would then find itself pinned in the "explorer" mode. Would make more sense if it would be pinned in the "properties" mode, which is the docked mode closest to the "rightSlidingSide" mode. Not being able to control the "pin" button has been a recurring question (including in my own head) over several years. But the NetBeans Team's window system guru Stan Aubrecht informed me today that a "previousMode" attribute exists in the "tc-ref" file of the TopComponent. Since a few releases, that file is generated via the annotations in the TopComponent. However, "previousMode" is currently not one of the attributes exposed by the @TopComponent.Registration annotation. Therefore, what I did was this: Set "rightSlidingSide" in the "mode" attribute of the @TopComponent.Registration. Build the module. Find the "generated-layer.xml" (in the Files window) and move the layer registration of the TopComponent, including its action and menu item for opening the TopComponent, into my own manual layer within the module. Then remove all the TopComponent annotations from the TopComponent, though you can keep @ConvertAsProperties and @Messages. Then add the "previousMode" attribute, as highlighted below, into my own layer file, i.e., within the tags copied from the "generated-layer.xml": <folder name="Modes"> <folder name="rightSlidingSide"> <file name="ComparatorTopComponent.wstcref"> <![CDATA[<?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE tc-ref PUBLIC "-//NetBeans//DTD Top Component in Mode Properties 2.0//EN" "http://www.netbeans.org/dtds/tc-ref2_0.dtd"> <tc-ref version="2.0"> <tc-id id="ComparatorTopComponent"/> <state opened="false"/> <previousMode name="properties" index="0" /> </tc-ref> ]]> </file> </folder> </folder> Now when you run the application and pin the specific TopComponent defined above, i.e., in the above case, named "ComparatorTopComponent", you will find it is pinned into the "properties" mode! That's pretty cool and if you agree, then you're a pretty cool NetBeans Platform developer, and I'd love to find out more about the application/s you're creating on the NetBeans Platform! Meanwhile, I'm going to create an issue for exposing the "previousMode" attribute in the @TopComponent.Registration annotation.

  Read the article

• "Optimal" game loop for 2D side-scroller

  - by MrDatabase

  Is it possible to describe an "optimal" (in terms of performance) layout for a 2D side-scroller's game loop? In this context the "game loop" takes user input, updates the states of game objects and draws the game objects. For example having a GameObject base class with a deep inheritance hierarchy could be good for maintenance... you can do something like the following: foreach(GameObject g in gameObjects) g.update(); However I think this approach can create performance issues. On the other hand all game objects' data and functions could be global. Which would be a maintenance headache but might be closer to an optimally performing game loop. Any thoughts? I'm interested in practical applications of near optimal game loop structure... even if I get a maintenance headache in exchange for great performance.

  Read the article

• JSR updates

  - by heathervc

  There were many JSR updates over the last week.  See below. JSR 258, Mobile User Interface Customization API, has published a Maintenance Release. JSR 257, Contactless Communication API, has published a Maintenance Release 2. JSR 180, SIP API for J2ME, has published a Final Release 5. JSR 269, Pluggable Annotation Processing API, has published a Maintenance Release. JSR 344, JavaServerTM Faces 2.2, has published an Early Draft Review.  The review closes on 8 December.

  Read the article

• How do I get to the maintenace shell?

  - by Narida

  I'm asking this because initially, my problem was this (power failure during installation, so I typed the following instructions in the maintenance shell: sudo mount -o remount,rw / sudo dpkg --configure a sudo mount -o remount,ro / sudo sync sudo reboot The first three lines worked, afterwards, my computer (a Dell Inspiron 530) got stalled for several hours, so I unplugged it. When I turned it on, the log in screen appeared, and after I try to write my password, it leads me back to the log screen. I must note that when I typed the first three lines during the maintenance shell mode, it said that the errors which were encountered during processing were: initscripts bluez gnome-bluetooth So, what do I have to do in order to get back to the maintenance shell so I can type code again? And, what code do I have to write in order to restore my computer? Thank you for your attention.

  Read the article

• ?Linux 6???UDEV??RAC ASM???????

  - by Liu Maclean(???)

  Maclean?????UDEV??ASMLIB?RAC???????????,???????????????????:Why ASMLIB and why not???UDEV????RAC ASM?????  ?«??UDEV????RAC ASM????? »???????????????,????????udev rule????: for i in b c d e f g h i j k ; do echo "KERNEL==\"sd*\", BUS==\"scsi\", PROGRAM==\"/sbin/scsi_id -g -u -s %p\", RESULT==\"`scsi_id -g -u -s /block/sd$i`\", NAME=\"asm-disk$i\", OWNER=\"grid\", GROUP=\"asmadmin\", MODE=\"0660\"" done ?????Linux 5?????, ????????redhat/Oracle Linux 6???????????? ????: ?OEL6??RHEL6?,????????? ??????:1. scsi_id??????????,scsi_id -g -u -s??????????2. udevtest???????,????udevadm??How to use udev for Oracle ASM in Oracle Linux 6   ???????????,???redhat/Oracle Linux 6??????udev rule ????: 1. #????? Linux 6.0???? [root@vrh6 dev]# cat /etc/issue Oracle Linux Server release 6.2 Kernel \r on an \m 2. #?????/etc/scsi_id.config echo "options=--whitelisted --replace-whitespace" >> /etc/scsi_id.config 3. #?????????udev?? [root@vrh6 dev]# ls -l sd* brw-rw----. 1 root disk 8, 0 Jun 30 09:29 sda brw-rw----. 1 root disk 8, 1 Jun 30 09:29 sda1 brw-rw----. 1 root disk 8, 2 Jun 30 09:29 sda2 brw-rw----. 1 root disk 8, 16 Jun 30 09:29 sdb brw-rw----. 1 root disk 8, 32 Jun 30 09:29 sdc brw-rw----. 1 root disk 8, 48 Jun 30 09:29 sdd brw-rw----. 1 root disk 8, 64 Jun 30 09:29 sde brw-rw----. 1 root disk 8, 80 Jun 30 09:29 sdf ??????? sdb-> sdf???????? 4. ? b->f?????for ???,??: # AUTO UDEV RULE BY Maclean Liu 2012/06/30 for i in b c d e f ; do echo "KERNEL==\"sd*\", BUS==\"scsi\", PROGRAM==\"/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/\$name\", RESULT==\"`/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/sd$i`\", NAME=\"asm-disk$i\", OWNER=\"grid\", GROUP=\"asmadmin\", MODE=\"0660\"" done ????sdb->sdf ?????RULE,????RULE???/etc/udev/rules.d/99-oracle-asmdevices.rules? ??????????? ,??RULE?99-oracle-asmdevices.rules # AUTO UDEV RULE BY Maclean Liu 2012/06/30 for i in b c d e f ; do echo "KERNEL==\"sd*\", BUS==\"scsi\", PROGRAM==\"/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/\$name\", RESULT==\"`/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/sd$i`\", NAME=\"asm-disk$i\", OWNER=\"grid\", GROUP=\"asmadmin\", MODE=\"0660\"" >> /etc/udev/rules.d/99-oracle-asmdevices.rules done 5. ?????root??/sbin/start_udev ?? ??????: [root@vrh6 dev]# echo "options=--whitelisted --replace-whitespace" >> /etc/scsi_id.config [root@vrh6 dev]# for i in b c d e f ; > do > echo "KERNEL==\"sd*\", BUS==\"scsi\", PROGRAM==\"/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/\$name\", RESULT==\"`/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/sd$i`\", NAME=\"asm-disk$i\", OWNER=\"grid\", GROUP=\"asmadmin\", MODE=\"0660\"" >> /etc/udev/rules.d/99-oracle-asmdevices.rules > done [root@vrh6 dev]# [root@vrh6 dev]# cat /etc/udev/rules.d/99-oracle-asmdevices.rules KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/$name", RESULT=="1ATA_VBOX_HARDDISK_VB09cadb31-cfbea255", NAME="asm-diskb", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/$name", RESULT=="1ATA_VBOX_HARDDISK_VB5f097069-59efb82f", NAME="asm-diskc", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/$name", RESULT=="1ATA_VBOX_HARDDISK_VB4e1a81c0-20478bc4", NAME="asm-diskd", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/$name", RESULT=="1ATA_VBOX_HARDDISK_VBdcce9285-b13c5a27", NAME="asm-diske", OWNER="grid", GROUP="asmadmin", MODE="0660" KERNEL=="sd*", BUS=="scsi", PROGRAM=="/sbin/scsi_id --whitelisted --replace-whitespace --device=/dev/$name", RESULT=="1ATA_VBOX_HARDDISK_VB82effe1a-dbca7dff", NAME="asm-diskf", OWNER="grid", GROUP="asmadmin", MODE="0660" [root@vrh6 dev]# [root@vrh6 dev]# /sbin/start_udev Starting udev: [ OK ] [root@vrh6 dev]# ls -l asm* brw-rw----. 1 grid asmadmin 8, 16 Jun 30 09:34 asm-diskb brw-rw----. 1 grid asmadmin 8, 32 Jun 30 09:34 asm-diskc brw-rw----. 1 grid asmadmin 8, 48 Jun 30 09:34 asm-diskd brw-rw----. 1 grid asmadmin 8, 64 Jun 30 09:34 asm-diske brw-rw----. 1 grid asmadmin 8, 80 Jun 30 09:34 asm-diskf

  Read the article

• Why has my computer started to make noises when I turn it on after I put it into sleep mode for the first time a week ago?

  - by Acid2

  I would usually have my pc on all day and fully shut it down at night time before I went to bed. I decided to put it into sleep mode instead the other day and everything was fine but when I woke it from sleep, I was presented with the blue screen of death and it started with some weird noise that sounded like some spinning part was off balance or possibly hitting something periodically. Sounds like it could be a fan or maybe the HDD. I'm not sure why sleep mode would mess up the hardware. Anyway, now sometimes, randomly, when I turn my computer on from a previous shut down, I still get to hear the noise but the start-up is normal. Sometimes I don't hear anything for the entire duration while I have it on and sometimes it goes away after a few minutes and sometimes it doesn't and I have to restart, like it isn't going away right now. I can hear the noise as I type this. Anyone got possible solutions? I don't want to open the system and mess up other stuff. I'm also not sure if I should take it somewhere to have it fixed - it might not make the noise then and work like normal and nothing would seem like needing to be fixed. Add: I'm running Windows 7, if that's of any relevance.

  Read the article

• ownership of hard drive recoveery of files Windows 7

  - by Jeff

  Here is the issue. I have an old laptop that died that was running xp. I now have a win 7 laptop. I need to get the files off the old drive. Win 7 will not let me take ownership of the drive. I can runn the comand prompt in regular mode and do a dir on the drive that shows up as Q: drive in regular mode. I gives me the volume as c and the serial number. I can not take ownership in regular mode with the comand prompt or other means. Microsoft site says use safe mode with networking. So I go to safe mode the drive shows up as G: in safe mode. I use the comand prompt Takeown /f G: and get the device is not ready error. I am at a loss. All I want is to retrieve my files from this drive. Any ideas or sugestions. I don't see how you can dir and get some info in one mode and not acces it in another. I have to get ownership and permissions fixed to get in the drive to get my files. Thanks in advance. I might add that I am using a usb3.0 to ide/sata cable adapter. Software came with the device but I can't make heads or tails out of the manual to know if any of the software can help me. The soft ware is PCClone Ex lite, and Clone Drive Soft ware

  Read the article

• convert xml document to comma delimited (CSV) file using xslt stylesheet.

  - by Brad H

  I need some assistance converting an xml document to a CSV file using an xslt stylesheet. I am trying to use the following xsl and I can't seem to get it right. I want my comma delimited file to include column headings, followed by the data. My biggest issues are removing the final comma after the last item and inserting a carriage return so each group of data appears on a separate line. I have been using XML Notepad. <xsl:template match="/"> <xsl:element name="table"> <xsl:apply-templates select="/*/*[1]" mode="header" /> <xsl:apply-templates select="/*/*" mode="row" /> </xsl:element> </xsl:template> <xsl:template match="*" mode="header"> <xsl:element name="tr"> <xsl:apply-templates select="./*" mode="column" /> </xsl:element> </xsl:template> <xsl:template match="*" mode="row"> <xsl:element name="tr"> <xsl:apply-templates select="./*" mode="node" /> </xsl:element> </xsl:template> <xsl:template match="*" mode="column"> <xsl:element name="th"> <xsl:value-of select="translate(name(.),'qwertyuiopasdfghjklzxcvbnm_','QWERTYUIOPASDFGHJKLZXCVBNM ')" /> </xsl:element>, </xsl:template> <xsl:template match="*" mode="node"> <xsl:element name="td"> <xsl:value-of select="." /> </xsl:element>, </xsl:template>

  Read the article

• Networking in VirtualBox

  - by Fat Bloke

  Networking in VirtualBox is extremely powerful, but can also be a bit daunting, so here's a quick overview of the different ways you can setup networking in VirtualBox, with a few pointers as to which configurations should be used and when. VirtualBox allows you to configure up to 8 virtual NICs (Network Interface Controllers) for each guest vm (although only 4 are exposed in the GUI) and for each of these NICs you can configure: Which virtualized NIC-type is exposed to the Guest. Examples include: Intel PRO/1000 MT Server (82545EM),  AMD PCNet FAST III (Am79C973, the default) or  a Paravirtualized network adapter (virtio-net). How the NIC operates with respect to your Host's physical networking. The main modes are: Network Address Translation (NAT) Bridged networking Internal networking Host-only networking NAT with Port-forwarding The choice of NIC-type comes down to whether the guest has drivers for that NIC.  VirtualBox, suggests a NIC based on the guest OS-type that you specify during creation of the vm, and you rarely need to modify this. But the choice of networking mode depends on how you want to use your vm (client or server) and whether you want other machines on your network to see it. So let's look at each mode in a bit more detail... Network Address Translation (NAT) This is the default mode for new vm's and works great in most situations when the Guest is a "client" type of vm. (i.e. most network connections are outbound). Here's how it works: When the guest OS boots,  it typically uses DHCP to get an IP address. VirtualBox will field this DHCP request and tell the guest OS its assigned IP address and the gateway address for routing outbound connections. In this mode, every vm is assigned the same IP address (10.0.2.15) because each vm thinks they are on their own isolated network. And when they send their traffic via the gateway (10.0.2.2) VirtualBox rewrites the packets to make them appear as though they originated from the Host, rather than the Guest (running inside the Host). This means that the Guest will work even as the Host moves from network to network (e.g. laptop moving between locations), and from wireless to wired connections too. However, how does another computer initiate a connection into a Guest?  e.g. connecting to a web server running in the Guest. This is not (normally) possible using NAT mode as there is no route into the Guest OS. So for vm's running servers we need a different networking mode.... Bridged Networking Bridged Networking is used when you want your vm to be a full network citizen, i.e. to be an equal to your host machine on the network. In this mode, a virtual NIC is "bridged" to a physical NIC on your host, like this: The effect of this is that each VM has access to the physical network in the same way as your host. It can access any service on the network such as external DHCP services, name lookup services, and routing information just as the host does. Logically, the network looks like this: The downside of this mode is that if you run many vm's you can quickly run out of IP addresses or your network administrator gets fed up with you asking for statically assigned IP addresses. Secondly, if your host has multiple physical NICs (e.g. Wireless and Wired) you must reconfigure the bridge when your host jumps networks.  Hmm, so what if you want to run servers in vm's but don't want to involve your network administrator? Maybe one of the next 2 modes is for you... Internal Networking When you configure one or more vm's to sit on an Internal network, VirtualBox ensures that all traffic on that network stays within the host and is only visible to vm's on that virtual network. Configuration looks like this: The internal network ( in this example "intnet" ) is a totally isolated network and so is very "quiet". This is good for testing when you need a separate, clean network, and you can create sophisticated internal networks with vm's that provide their own services to the internal network. (e.g. Active Directory, DHCP, etc). Note that not even the Host is a member of the internal network, but this mode allows vm's to function even when the Host is not connected to a network (e.g. on a plane). Note that in this mode, VirtualBox provides no "convenience" services such as DHCP, so your machines must be statically configured or one of the vm's needs to provide a DHCP/Name service. Multiple internal networks are possible and you can configure vm's to have multiple NICs to sit across internal and other network modes and thereby provide routes if needed. But all this sounds tricky. What if you want an Internal Network that the host participates on with VirtualBox providing IP addresses to the Guests? Ah, then for this, you might want to consider Host-only Networking... Host-only Networking Host-only Networking is like Internal Networking in that you indicate which network the Guest sits on, in this case, "vboxnet0": All vm's sitting on this "vboxnet0" network will see each other, and additionally, the host can see these vm's too. However, other external machines cannot see Guests on this network, hence the name "Host-only". Logically, the network looks like this: This looks very similar to Internal Networking but the host is now on "vboxnet0" and can provide DHCP services. To configure how a Host-only network behaves, look in the VirtualBox Manager...Preferences...Network dialog: Port-Forwarding with NAT Networking Now you may think that we've provided enough modes here to handle every eventuality but here's just one more... What if you cart around a mobile-demo or dev environment on, say, a laptop and you have one or more vm's that you need other machines to connect into? And you are continually hopping onto different (customer?) networks. In this scenario: NAT - won't work because external machines need to connect in. Bridged - possibly an option, but does your customer want you eating IP addresses and can your software cope with changing networks? Internal - we need the vm(s) to be visible on the network, so this is no good. Host-only - same problem as above, we want external machines to connect in to the vm's. Enter Port-forwarding to save the day! Configure your vm's to use NAT networking; Add Port Forwarding rules; External machines connect to "host":"port number" and connections are forwarded by VirtualBox to the guest:port number specified. For example, if your vm runs a web server on port 80, you could set up rules like this:  ...which reads: "any connections on port 8080 on the Host will be forwarded onto this vm's port 80".  This provides a mobile demo system which won't need re-configuring every time you open your laptop lid. Summary VirtualBox has a very powerful set of options allowing you to set up almost any configuration your heart desires. For more information, check out the VirtualBox User Manual on Virtual Networking. -FB 

  Read the article

< Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >