Search Results

Search found 19557 results on 783 pages for 'networking programming'.

Page 75/783 | < Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >

• Atheros AR8132 Ethernet refuses to connect after suspend

  - by Ramesh Patel

  I'm having an issue where my ethernet card (Atheros Communications Inc. AR8132 Fast Ethernet (rev c0)) refuses to recognize when a network cable is plugged in after a suspend. This is dmesg after suspending: [135897.712049] atl1c 0000:02:00.0: MAC state machine can't be idle since disabled for 10ms second [135897.743729] ADDRCONF(NETDEV_UP): eth0: link is not ready [135898.541804] ADDRCONF(NETDEV_UP): eth1: link is not ready [135900.452077] atl1c 0000:02:00.0: irq 47 for MSI/MSI-X [135900.672262] atl1c 0000:02:00.0: Error get phy ID [135900.673060] ADDRCONF(NETDEV_UP): eth0: link is not ready [135900.674140] ADDRCONF(NETDEV_UP): eth0: link is not ready [135925.604052] [135935.776051] eth1: no IPv6 routers present eth0 is the ethernet card and eth1 is the wlan card (Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01)). The ethernet card uses the atl1c driver and the wlan card uses the wl driver. Sorry, should have mentioned as well, running Ubuntu 12.04 with kernel 3.2.0-25-generic.

  Read the article

• Intel 82576 Network card

  - by No1_Melman

  I have an Intel dual port pcie NIC card with two 82576 interfaces according to ubuntu 12.04. I run the command sudo lshw -html > /home/melman/Documents/hardware.html and it shows both of the interfaces but they're grayed out?! How can enable them? ifconfig output: bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:192.168.100.2 Bcast:192.168.100.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr e0:69:95:d1:db:ff inet addr:192.168.10.63 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::e269:95ff:fed1:dbff/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2903 errors:0 dropped:0 overruns:0 frame:0 TX packets:2627 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1524738 (1.5 MB) TX bytes:430196 (430.1 KB) Interrupt:20 Memory:f7f00000-f7f20000 eth3 Link encap:Ethernet HWaddr 00:50:b6:50:a7:f9 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth4 Link encap:Ethernet HWaddr 00:1b:21:6e:99:77 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Memory:f7c00000-f7c20000 eth5 Link encap:Ethernet HWaddr 00:1b:21:6e:99:76 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Memory:f7c20000-f7c40000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:246 errors:0 dropped:0 overruns:0 frame:0 TX packets:246 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:17584 (17.5 KB) TX bytes:17584 (17.5 KB)

  Read the article

• How to protect a peer-to-peer network from inappropriate content?

  - by Mike

  I’m developing a simple peer-to-peer app in .Net which should enable users to share specific content (text and picture files). As I've learned with my last question, inappropriate content can “relatively” easily be identified / controlled in a centralized environment. But what about a peer-to-peer network, what are the best methods to protect a decentralized system from unwanted (illegal) content? At the moment I only see the following two methods: A protocol (a set of rules) defines what kind of data (e.g. only .txt and jpg-files, not bigger than 20KB etc.) can be shared over the p2p-network and all clients (peers) must implement this protocol. If a peer doesn’t, it gets blocked by other peers. Pro: easy to implement. Con: It’s not possible to define the perfect protocol (I think eMail-Spam filters have the same problem) Some kind of rating/reputation system must be implemented (similar to stackoverflow), so “bad guys” and inappropriate content can be identified / blocked by other users. Pro: Would be very accurate. Con: Would be slow and in my view technically very hard to implement. Are there other/better solutions? Any answer or comment is highly appreciated.

  Read the article

• Using proxy on my Ubuntu 12.04 and proxy exception problem

  - by user1343713

  im new in linux systems. I recently installed Ubuntu 12.04 LTS and it works fine with me, but i have a problem. I live in the university dorms and in order to use internet i have to put proxy settings which require authentication, i had a problem with downloading from the store but i read the solution you wrote here still sometimes it works sometimes :( i dont know why. But the big problem is if i want to open any link from inside the university i have to disable the proxy, on Windows there were an exception for using the proxy you can easily do it. is there any possible way of doing that in Ubuntu 12.04 Thank you for being helpful

  Read the article

• [MISC GEEKERY] How To Easily Access Your Home Network From Anywhere With DDNS

  - by YatriTrivedi

  Whether you’re hosting a web page or running a Minecraft server, it’s a pain to keep track of IP addresses. Using a free dynamic DNS, you can turn 174.45.19.242 into mygeekydns.dyndns.org and be free from changing IPs.How To Recover After Your Email Password Is CompromisedHow to Clean Your Filthy Keyboard in the Dishwasher (Without Ruining it)Learn How to Make HDR Images in Photoshop or GIMP With a Simple Trick

  Read the article

• Mirroring Ubuntu on several systems in a computer lab

  - by Harvey Steck

  I am working in a new refugee school where the only Internet service available is a slow satellite connection. We are about to set up a computer lab (already have desktop systems and am about to install Ubuntu on them). I'm a newbie when it comes to Linux, but it seems a better alternative than pirated copies of Windows. I'd like to set up one Ubuntu system, and then mirror that system on perhaps ten to twenty other systems (all of which would be on an ethernet network). I expect to have an internet connection on the one system that I set up, but then it may be difficult to have enough bandwidth to go through all the same steps on the other ten systems. Can I set up the other ten or twenty computers to get all of their updates/upgrades/configuration from one master system? Can I also set things up so that students cannot change the configuration, install new programs, etc.? Appreciate any help you can give. -- Harvey

  Read the article

• How do I add a network printer in Ubuntu 12.04?

  - by Ricky Robinson

  I know the name and the IP address of a network printer, but I can't seem to be able to search by IP address or name. Ubuntu developers love to move things around to make it difficult for users, so now with Ubuntu 12.04 I can only go on Application -> System Tools -> System Settings -> Printers, click on Network and a list of printers appears. Too bad the one I want to add isn't there. How do I do it? Here it suggests System -> Administration -> Printing, which simply doesn't exist.

  Read the article

• Wireless shows up as disabled, how can I get it working?

  - by Lazer

  $ sudo iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off pan0 no wireless extensions. $ This is what pops up when I click the two computers icon What should I do to get Wifi working on this machine? $ sudo ifconfig wlan0 up SIOCSIFFLAGS: No such file or directory $ $ lspci | tail 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: ATI Technologies Inc M92 LP [Mobility Radeon HD 4300 Series] 09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 13) 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) $

  Read the article

• Is this an apt-get issue or network issue?

  - by zharvey

  I just installed my first Ubuntu server (12.04) instance and immediately am noticing a few things: Running apt-get install or update fails (see below) Running ifconfig produces peculiar IP addresses starting with 10.x.x.x and my router does not see the server at all in its "Attached Devices" page (its a consumer grade Netgear) When I run apt-get I get 50+ of the following errors: Failed to fetch <some-http-url. Temporary failure resolving <blah.ubuntu.com I read up on this error for 12.04, and found some similar posts on this forum and on serverfault that recommended going into /etc/resolv.conf and adding an entry: nameserver 8.8.8.8 To my surprise, I found that /etc/resolve.conf was a symlink pointing to somewhere else and I had to delete it first, then create a new one with the entry indicated above. I restarted the server and tried running apt-get again: same results. How do I start diagnosing the problem (I'm a relatively new Linux/Ubuntu user)? Additional details that may help: This is actually a virtual machine running as a VirtualBox guest OS The physical host that is running this VM is my laptop which has a wireless connection; I'm wondering if (somehow) the laptop is getting the network wirelessly, but perhaps either the VBox VM and/or the Ubuntu server OS isn't configured for wireless and so nothing is "getting through"? Thanks in advance for any pointers! Edit: Here is a snapshot of my VM's Network settings (only Adapter 1 has any information populating its fields, so I assume my VM has only 1 adapter): Here is the output when I run ifconfig from the terminal: And here is the output when I run route from the terminal: Running ping google.com:

  Read the article

• Programming and Ubiquitous Language (DDD) in a non-English domain

  - by Sandor Drieënhuizen

  I know there are some questions already here that are closely related to this subject but none of them take Ubiquitous Language as the starting point so I think that justifies this question. For those who don't know: Ubiquitous Language is the concept of defining a (both spoken and written) language that is equally used across developers and domain experts to avoid inconsistencies and miscommunication due to translation problems and misunderstanding. You will see the same terminology show up in code, conversations between any team member, functional specs and whatnot. So, what I was wondering about is how to deal with Ubiquitous Language in non-English domains. Personally, I strongly favor writing programming code in English completely, including comments but ofcourse excluding constants and resources. However, in a non-English domain, I'm forced to make a decision either to: Write code reflecting the Ubiquitous Language in the natural language of the domain. Translate the Ubiquitous Language to English and stop communicating in the natural language of the domain. Define a table that defines how the Ubiquitous Language translates to English. Here are some of my thoughts based on these options: 1) I have a strong aversion against mixed-language code, that is coding using type/member/variable names etc. that are non-English. Most programming languages 'breathe' English to a large extent and most of the technical literature, design pattern names etc. are in English as well. Therefore, in most cases there's just no way of writing code entirely in a non-English language so you end up with mixed languages anyway. 2) This will force the domain experts to start thinking and talking in the English equivalent of the UL, something that will probably not come naturally to them and therefore hinders communication significantly. 3) In this case, the developers communicate with the domain experts in their native language while the developers communicate with each other in English and most importantly, they write code using the English translation of the UL. I'm sure I don't want to go for the first option and I think option 3 is much better than option 2. What do you think? Am I missing other options? UPDATE Today, about year later, having dealt with this issue on a daily basis, I have to say that option 3 has worked out pretty well for me. It wasn't as tedious as I initially feared and translating in real time while talking to the client wasn't a problem either. I also found the following advantages to be true, based on my experience. Translating the UL makes you pay more attention to defining the UL and even the domain itself, especially when you don't know how to translate a term and you have to start looking through dictionaries etc. This has even caused me to reconsider domain modeling decisions a few times. It helps you make your knowledge of the English language more profound. Obviously, your code is much more pleasant to look at instead of being a mind boggling obscenity.

  Read the article

• How do I install drivers for the Atheros AR8161 Ethernet controller?

  - by Jessica Burnett

  I have installed Ubuntu 12.04-64 bit on my Lenovo IdeaPad laptop, and the wired Ethernet (LAN) connection doesn't work. Running the lspci -vv | grep Atheros command from the terminal shows me I have the AR8161 Gigabit Ethernet controller: 02:00.0 Ethernet controller: Atheros Communications Inc. AR8161 Gigabit Ethernet (rev 08) This looks like a new product whose drivers are not built into Ubuntu. How do I install drivers to get the AR8161 working?

  Read the article

• Wireless shows up as disabled, how can I get it working?

  - by Lazer

  $ sudo iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off pan0 no wireless extensions. $ This is what pops up when I click the two computers icon What should I do to get Wifi working on this machine? $ sudo ifconfig wlan0 up SIOCSIFFLAGS: No such file or directory $ $ lspci | tail 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: ATI Technologies Inc M92 LP [Mobility Radeon HD 4300 Series] 09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 13) 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) $

  Read the article

• Books and stories on programming culture, specifically in the 80's / early 90's

  - by Ivo van der Wijk

  I've enjoyed a number of (fiction/non-fiction books) about hacker culture and running a software business in the 80's, 90's. For some reason things seemed so much more exciting back then. Examples are: Microserfs (Douglas Coupland) Accidental Empires (Robert X. Cringely Almost Pefect (W.E. Peterson, online!) Coders at Work (Peter Seibel) Today I'm an entrepeneur and programmer. Back in the 80's a I was a young geek hacking DOS TSR's and coding GWBasic / QBasic. In the 90's I was a C.S. university student, experiencing the rise of the Internet world wide. When reading these books running a software business seemed so much more fun than it is nowadays. Things used to be so much simpler, opportunities seemed to be everywhere and the startups seemed to work with much more real problems (inventing spreadsheets, writing word processors in assembly on 6 different platforms) than all our current web 2.0 social networking toys. Does anyone share these feelings? Does anyone have any good (personal) stories from back then or know of other good books to read?

  Read the article

• Cannot connect to secure wireless with Netgear wna3100 USB

  - by Vince Radice

  I have installed Ubuntu 11.10. I used a wired connection to download and install all of the updates. When I tried to use a Netgear WNA3100 wireless USB network adapter, it failed. Much searching and trying things I was finally able to get it working by disabling security on my router. I have verified this by disabling security and I was able to connect. When I enabled security (WPA2 PSK), the connection failed. What is necessary to enable security (WPA2 PSK) and still use the Netgear USB interface? Here is the output from the commands most requested lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0846:9020 NetGear, Inc. WNA3100(v1) Wireless-N 300 [Broadcom BCM43231] lshw -C network *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:40:ca:44:e6:3e size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=32 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:c800(size=256) memory:ee011000-ee0110ff memory:40000000-4000ffff *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: e0:91:f5:56:e1:0d capabilities: ethernet physical wireless configuration: broadcast=yes driver=ndiswrapper+bcmn43xx32 driverversion=1.56+,08/26/2009, 5.10.79.30 ip=192.168.1.104 link=yes multicast=yes wireless=IEEE 802.11g iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11g ESSID:"vincecarolradice" Mode:Managed Frequency:2.422 GHz Access Point: A0:21:B7:9F:E5:EE Bit Rate=121.5 Mb/s Tx-Power:32 dBm RTS thr:2347 B Fragment thr:2346 B Encryption key:off Power Management:off Link Quality:76/100 Signal level:-47 dBm Noise level:-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ndiswrapper -l bcmn43xx32 : driver installed device (0846:9020) present lsmod | grep ndis ndiswrapper 193669 0 dmesg | grep -e ndis -e wlan [ 907.466392] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 907.838507] ndiswrapper (import:233): unknown symbol: ntoskrnl.exe:'IoUnregisterPlugPlayNotification' [ 907.838955] ndiswrapper: driver bcmwlhigh5 (Netgear,11/05/2009, 5.60.180.11) loaded [ 908.137940] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmwlhigh5, version: 0x53cb40b, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 908.141879] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 908.143048] usbcore: registered new interface driver ndiswrapper [ 908.178826] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 994.015088] usbcore: deregistering interface driver ndiswrapper [ 994.028892] ndiswrapper: device wlan0 removed [ 994.080558] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 994.374929] ndiswrapper: driver bcmn43xx32 (,08/26/2009, 5.10.79.30) loaded [ 994.404366] ndiswrapper (mp_init:219): couldn't initialize device: C0000001 [ 994.404384] ndiswrapper (pnp_start_device:435): Windows driver couldn't initialize the device (C0000001) [ 994.404666] ndiswrapper (mp_halt:262): device e05b6480 is not initialized - not halting [ 994.404671] ndiswrapper: device eth%d removed [ 994.404709] ndiswrapper: probe of 1-5:1.0 failed with error -22 [ 994.406318] usbcore: registered new interface driver ndiswrapper [ 2302.058692] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmn43xx32, version: 0x50a4f1e, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 2302.060882] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 2302.113838] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2354.611318] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2355.268902] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2365.400023] wlan0: no IPv6 routers present [ 2779.226096] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2779.422343] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2797.574474] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2802.607937] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2803.261315] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2813.952028] wlan0: no IPv6 routers present [ 3135.738431] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3139.180963] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3139.816561] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.229872] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.444542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.758297] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.860684] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.118732] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.139553] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.300542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3353.341402] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3363.266399] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.505475] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.506619] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3363.717203] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.779206] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.206152] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.248624] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.577664] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3438.852457] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3438.908573] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.282995] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.325237] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.460716] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.461763] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.809776] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.880641] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.122848] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.148328] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.324502] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3636.088798] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3636.712186] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 3647.600040] wlan0: no IPv6 routers present I am using the system now with the router security turned off. When I submit this, I will turn security back on.

  Read the article

• Buzzword for "performance-aware" software development

  - by errantlinguist

  There seems to be an overabundance of buzzwords for software development styles and methodologies: Agile development, extreme programming, test-driven development, etc... well, is there any sort of buzzword for "performance-aware" development? By "performance awareness", I don't necessarily mean low-latency or low-level programming, although the former would logically fall under the blanket term I'm looking for. I mean development in which resources are recognised to be finite and so there is a general emphasis on low computational complexity, good resource management, etc. If I was to be snarky, I would say "good programming", but that doesn't seem to get the message across so well...

  Read the article

• How to make ad-hoc network connection?

  - by Johan Nathaniel Soedjono

  I can't make ad-hoc from my netbook (Ubuntu 12.04). It has internet source from ethernet. I have tried making from network manager. But it always says 'Wireless Network Disconnected' and can't be detected by neither my other laptop nor my cell phone which have wifi. How can I make adhoc from it? I have already tried making a connection in Network Manager a lot of times, but it still can't connect and appear notification 'Wireless Network Disconnected'.

  Read the article

• Resetting network adapter?

  - by Quixo

  I'm running Ubuntu 12.04. I get a strong wireless signal throughout my house, and the wireless symbol in the upper-right-hand corner shows that it's connected. The problem is, occasionally I am unable to access the internet (still having a strong symbol). This happened with Windows 7, too, but running the network troubleshooter fixed it each time. It claimed to be "resetting the network adapter". So, what I need to know is: How do I replicate that process on Ubuntu? Thanks for your help!

  Read the article

• Wireless Connected But No Internet Connection (Ubuntu 12.04)

  - by Zxy

  I am using same network for 2 days and everything was normal. However, today even though it shows me as connected to the network, I do not have internet connection. If I use ethernet cable instead of wireless, I am still able to connect to the internet. Also my friends are able to connect to the wireless network and they can get internet connection. I did not update or install anything since yesterday. Therefore I do not have any idea why it is happening. Here is some information about my connection: I will be appreciate to any kind of help. root@ghostrider:/etc/resolvconf# ping 127.0.0.1 PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data. 64 bytes from 127.0.0.1: icmp_req=1 ttl=64 time=0.042 ms 64 bytes from 127.0.0.1: icmp_req=2 ttl=64 time=0.023 ms 64 bytes from 127.0.0.1: icmp_req=3 ttl=64 time=0.036 ms 64 bytes from 127.0.0.1: icmp_req=4 ttl=64 time=0.040 ms ^C --- 127.0.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2998ms rtt min/avg/max/mdev = 0.023/0.035/0.042/0.008 ms root@ghostrider:/etc/resolvconf# ping 192.168.1.3 PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data. ^C --- 192.168.1.3 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18143ms root@ghostrider:/etc/resolvconf# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. ^C --- 8.8.8.8 ping statistics --- 11 packets transmitted, 0 received, 100% packet loss, time 10079ms root@ghostrider:/etc/resolvconf# cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04 LTS" Linux ghostrider 3.2.0-24-generic-pae #39-Ubuntu SMP Mon May 21 18:54:21 UTC 2012 i686 i686 i386 GNU/Linux root@ghostrider:/etc/resolvconf# lspci -nnk | grep -iA2 net 03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8131 Gigabit Ethernet [1969:1063] (rev c0) Subsystem: Lenovo Device [17aa:3956] Kernel driver in use: atl1c -- 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] Kernel driver in use: wl root@ghostrider:/etc/resolvconf# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 007: ID 0489:e00d Foxconn / Hon Hai Bus 001 Device 004: ID 1c7a:0801 LighTuning Technology Inc. Fingerprint Reader Bus 001 Device 005: ID 064e:f219 Suyin Corp. Bus 002 Device 010: ID 0424:2412 Standard Microsystems Corp. Bus 002 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 002 Device 011: ID 0403:6010 Future Technology Devices International, Ltd FT2232C Dual USB-UART/FIFO IC root@ghostrider:/etc/resolvconf# iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz Access Point: 00:16:E3:40:C3:E4 Bit Rate=54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=-52 dBm Noise level=-97 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. root@ghostrider:/etc/resolvconf# rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 5: hci0: Bluetooth Soft blocked: no Hard blocked: no root@ghostrider:/etc/resolvconf# lsmod Module Size Used by nls_iso8859_1 12617 0 nls_cp437 12751 0 vfat 17308 0 fat 55605 1 vfat usb_storage 39646 0 uas 17828 0 snd_hda_codec_realtek 174055 1 rfcomm 38139 12 parport_pc 32114 0 ppdev 12849 0 bnep 17830 2 joydev 17393 0 ftdi_sio 35859 1 usbserial 37173 3 ftdi_sio snd_hda_intel 32765 3 snd_hda_codec 109562 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec acer_wmi 23612 0 hid_logitech_dj 18177 0 snd_pcm 80845 2 snd_hda_intel,snd_hda_codec uvcvideo 67203 0 btusb 17912 2 snd_seq_midi 13132 0 videodev 86588 1 uvcvideo bluetooth 158438 23 rfcomm,bnep,btusb psmouse 72919 0 usbhid 41906 1 hid_logitech_dj snd_rawmidi 25424 1 snd_seq_midi intel_ips 17753 0 serio_raw 13027 0 root@ghostrider:/etc/resolvconf# ping 127.0.0.1 PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data. 64 bytes from 127.0.0.1: icmp_req=1 ttl=64 time=0.042 ms 64 bytes from 127.0.0.1: icmp_req=2 ttl=64 time=0.023 ms 64 bytes from 127.0.0.1: icmp_req=3 ttl=64 time=0.036 ms 64 bytes from 127.0.0.1: icmp_req=4 ttl=64 time=0.040 ms ^C --- 127.0.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2998ms rtt min/avg/max/mdev = 0.023/0.035/0.042/0.008 ms root@ghostrider:/etc/resolvconf# ping 192.168.1.3 PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data. ^C --- 192.168.1.3 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18143ms root@ghostrider:/etc/resolvconf# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. ^C --- 8.8.8.8 ping statistics --- 11 packets transmitted, 0 received, 100% packet loss, time 10079ms root@ghostrider:/etc/resolvconf# cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04 LTS" Linux ghostrider 3.2.0-24-generic-pae #39-Ubuntu SMP Mon May 21 18:54:21 UTC 2012 i686 i686 i386 GNU/Linux root@ghostrider:/etc/resolvconf# lspci -nnk | grep -iA2 net 03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8131 Gigabit Ethernet [1969:1063] (rev c0) Subsystem: Lenovo Device [17aa:3956] Kernel driver in use: atl1c -- 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] Kernel driver in use: wl root@ghostrider:/etc/resolvconf# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 007: ID 0489:e00d Foxconn / Hon Hai Bus 001 Device 004: ID 1c7a:0801 LighTuning Technology Inc. Fingerprint Reader Bus 001 Device 005: ID 064e:f219 Suyin Corp. Bus 002 Device 010: ID 0424:2412 Standard Microsystems Corp. Bus 002 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 002 Device 011: ID 0403:6010 Future Technology Devices International, Ltd FT2232C Dual USB-UART/FIFO IC root@ghostrider:/etc/resolvconf# iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz Access Point: 00:16:E3:40:C3:E4 Bit Rate=54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=-52 dBm Noise level=-97 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. root@ghostrider:/etc/resolvconf# rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 5: hci0: Bluetooth Soft blocked: no Hard blocked: no root@ghostrider:/etc/resolvconf# lsmod Module Size Used by nls_iso8859_1 12617 0 nls_cp437 12751 0 vfat 17308 0 fat 55605 1 vfat usb_storage 39646 0 uas 17828 0 snd_hda_codec_realtek 174055 1 rfcomm 38139 12 parport_pc 32114 0 ppdev 12849 0 bnep 17830 2 joydev 17393 0 ftdi_sio 35859 1 usbserial 37173 3 ftdi_sio snd_hda_intel 32765 3 snd_hda_codec 109562 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec acer_wmi 23612 0 hid_logitech_dj 18177 0 snd_pcm 80845 2 snd_hda_intel,snd_hda_codec uvcvideo 67203 0 btusb 17912 2 snd_seq_midi 13132 0 videodev 86588 1 uvcvideo bluetooth 158438 23 rfcomm,bnep,btusb psmouse 72919 0 usbhid 41906 1 hid_logitech_dj snd_rawmidi 25424 1 snd_seq_midi intel_ips 17753 0 serio_raw 13027 0 hid 77367 2 hid_logitech_dj,usbhid ideapad_laptop 17890 0 sparse_keymap 13658 2 acer_wmi,ideapad_laptop lib80211_crypt_tkip 17275 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event wl 2646601 0 wmi 18744 1 acer_wmi i915 414672 3 drm_kms_helper 45466 1 i915 snd_timer 28931 2 snd_pcm,snd_seq mac_hid 13077 0 snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq lib80211 14040 2 lib80211_crypt_tkip,wl drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 snd 62064 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_se q,snd_timer,snd_seq_device video 19068 1 i915 mei 36570 0 soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp atl1c 36718 0 root@ghostrider:/etc/resolvconf# nm-tool NetworkManager Tool State: connected (global) - Device: eth1 [PoliTekno] ---------------------------------------------------- Type: 802.11 WiFi Driver: wl State: connected Default: yes HW Address: AC:81:12:7F:6B:B2 Capabilities: Speed: 54 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) CnDStudios: Infra, 00:12:BF:3F:0A:8A, Freq 2412 MHz, Rate 54 Mb/s, Strength 85 WPA AIR_TIES: Infra, 00:1C:A8:6E:84:32, Freq 2462 MHz, Rate 54 Mb/s, Strength 72 WPA2 VKSS: Infra, 00:E0:4D:01:0D:47, Freq 2452 MHz, Rate 54 Mb/s, Strength 62 WPA2 PROGEDA: Infra, 00:1A:2A:60:BF:61, Freq 2462 MHz, Rate 54 Mb/s, Strength 47 WPA MobilAtolye: Infra, 72:2B:C1:65:75:3C, Freq 2422 MHz, Rate 54 Mb/s, Strength 35 WPA WPA2 AIRTIES_WAR-141: Infra, 00:1C:A8:AB:AA:48, Freq 2422 MHz, Rate 54 Mb/s, Strength 35 WPA WPA2 tilda_biri_yeni: Infra, 54:E6:FC:B0:3C:E9, Freq 2437 MHz, Rate 0 Mb/s, Strength 34 WEP *PoliTekno: Infra, 00:16:E3:40:C3:E4, Freq 2462 MHz, Rate 54 Mb/s, Strength 100 WPA2 AIRTIES_RJY: Infra, 00:1A:2A:BD:85:16, Freq 2462 MHz, Rate 54 Mb/s, Strength 55 WEP IPv4 Settings: Address: 0.0.0.0 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: F0:DE:F1:6C:90:65 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: off root@ghostrider:/etc/resolvconf# sudo iwlist scan lo Interface doesn't support scanning. eth1 Scan completed : Cell 01 - Address: 00:16:E3:40:C3:E4 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:5/5 Signal level:-48 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 02 - Address: 00:E0:4D:01:0D:47 ESSID:"VKSS" Mode:Managed Frequency:2.452 GHz (Channel 9) Quality:4/5 Signal level:-64 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Cell 03 - Address: 00:1C:A8:AB:AA:48 ESSID:"AIRTIES_WAR-141" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:2/5 Signal level:-77 dBm Noise level:-95 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: DDB20050F204104A0001101049001E007FC5100018DE7CF0D8B70223A62711C18926AC290E30303030303139631044000102103B0001031047001076B31BC241E953CB99C3872554425A28102100194169725469657320576972656C657373204E6574776F726B73102300074169723534343010240008312E322E302E31321042000F4154303939313131383030323832351054000800060050F20400011011000741697235343430100800020084103C000103 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 04 - Address: 72:2B:C1:65:75:3C ESSID:"MobilAtolye" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:2/5 Signal level:-78 dBm Noise level:-92 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK IE: Unknown: DDA20050F204104A0001101044000102103B00010310470010BC329E001DD811B28601722BC165753C1021001D48756177656920546563686E6F6C6F6769657320436F2E2C204C74642E1023001C48756177656920576972656C6573732041636365737320506F696E74102400065254323836301042000831323334353637381054000800060050F204000110110009487561776569415053100800020084103C000100 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s 18 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 12 Mb/s 24 Mb/s; 48 Mb/s Cell 05 - Address: 00:12:BF:3F:0A:8A ESSID:"CnDStudios" Mode:Managed Frequency:2.412 GHz (Channel 1) Quality:5/5 Signal level:-47 dBm Noise level:-95 dBm IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Cell 06 - Address: 00:1C:A8:6E:84:32 ESSID:"AIR_TIES" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:5/5 Signal level:-56 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Cell 07 - Address: 54:E6:FC:B0:3C:E9 ESSID:"tilda_biri_yeni" Mode:Managed Frequency:2.437 GHz (Channel 6) Quality:1/5 Signal level:-85 dBm Noise level:-99 dBm Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s 48 Mb/s; 54 Mb/s Cell 08 - Address: 18:28:61:16:57:C3 ESSID:"obilet" Mode:Managed Frequency:2.437 GHz (Channel 6) Quality:1/5 Signal level:-88 dBm Noise level:-99 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 09 - Address: 00:1A:2A:60:BF:61 ESSID:"PROGEDA" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:2/5 Signal level:-75 dBm Noise level:-98 dBm IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s eth0 Interface doesn't support scanning.

  Read the article

• Ubuntu 10.04 LTS server update / upgrade issue

  - by user92603

  I have a starnge problem here with my Ubuntu 10.04 LTS server. When I try to update the server I got messages Err and warning, here an eg: sudo apt-get update Err http://fr.archive.ubuntu.com lucid Release.gpg W: Impossible de récupérer http://security.ubuntu.com/ubuntu/dists/lucid-security/multiverse/i18n/Translation-fr.bz2 Erreur temporaire de résolution de «*security.ubuntu.com*» but my server is connected and if I try to ping some DNS server (eg: 8.8.8.8 ) it works ! Can some one help me on that issue ?

  Read the article

• Transfer domains without disrupting local email server

  - by krosiris

  Perhaps I am thinking about this wrong, but maybe some of you guys can help me on this one. I have a client who currently has a domain from network solutions and is hosted via GoDaddy. Additionally, he his has email service with GoDaddy as well, but it seems to be forwarded to his local server at work. How can I transfer hosting accounts without disrupting email service (or at least temporarily)? Some MX info via Godaddy: A @ Points to GoDaddy Host main Points to client's home server sw Points to client's home server MX @ Points to main.example.com @ Points to smtp.secureserver @ Points to mailstore1.secureserver

  Read the article

• How do I prevent missing network from slowing down boot-up?

  - by Ravi S Ghosh

  I have been having rather slow boot on Ubuntu 12.04. Lately, I tried to figure out the reason and it seems to be the network connection which does not get connected and requires multiple attempts. Here is part of dmesg [ 2.174349] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 2.174352] EXT4-fs (sda2): write access will be enabled during recovery [ 2.308172] firewire_core: created device fw0: GUID 384fc00005198d58, S400 [ 2.333457] usb 7-1.2: new low-speed USB device number 3 using uhci_hcd [ 2.465896] EXT4-fs (sda2): recovery complete [ 2.466406] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.589440] usb 7-1.3: new low-speed USB device number 4 using uhci_hcd **[ 18.292029] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 18.458958] udevd[377]: starting version 175 [ 18.639482] Adding 4200960k swap on /dev/sda5. Priority:-1 extents:1 across:4200960k [ 19.314127] wmi: Mapper loaded [ 19.426602] r592 0000:09:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.426739] r592: driver successfully loaded [ 19.460105] input: Dell WMI hotkeys as /devices/virtual/input/input5 [ 19.493629] lp: driver loaded but no devices found [ 19.497012] cfg80211: Calling CRDA to update world regulatory domain [ 19.535523] ACPI Warning: _BQC returned an invalid level (20110623/video-480) [ 19.539457] acpi device:03: registered as cooling_device2 [ 19.539520] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6 [ 19.539568] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 19.578060] Linux video capture interface: v2.00 [ 19.667708] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 19.763171] r852 0000:09:01.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.763258] r852: driver loaded successfully [ 19.854769] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.0/input/input7 [ 19.854864] generic-usb 0003:045E:00DD.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input0 [ 19.878605] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.1/input/input8 [ 19.878698] generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input1 [ 19.902779] input: DELL DELL USB Laser Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.3/7-1.3:1.0/input/input9 [ 19.925034] generic-usb 0003:046D:C063.0003: input,hidraw2: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:1d.1-1.3/input0 [ 19.925057] usbcore: registered new interface driver usbhid [ 19.925059] usbhid: USB HID core driver [ 19.942362] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:63ea) [ 19.947004] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input10 [ 19.947075] usbcore: registered new interface driver uvcvideo [ 19.947077] USB Video Class driver (1.1.1) [ 20.145232] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 20.145235] Copyright(c) 2003-2011 Intel Corporation [ 20.145327] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 20.145357] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 20.145402] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 20.145404] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90000674000 [ 20.145407] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 20.145531] iwlwifi 0000:04:00.0: irq 46 for MSI/MSI-X [ 20.145613] iwlwifi 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54 [ 20.145720] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 20.167535] iwlwifi 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4 [ 20.167538] iwlwifi 0000:04:00.0: Device SKU: 0Xf0 [ 20.167567] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels [ 20.172779] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 20.172783] Disabling lock debugging due to kernel taint [ 20.250115] [fglrx] Maximum main memory to use for locked dma buffers: 3759 MBytes. [ 20.250567] [fglrx] vendor: 1002 device: 9553 count: 1 [ 20.251256] [fglrx] ioport: bar 1, base 0x2000, size: 0x100 [ 20.251271] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 20.251277] pci 0000:01:00.0: setting latency timer to 64 [ 20.251559] [fglrx] Kernel PAT support is enabled [ 20.251578] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 20.310385] iwlwifi 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692 [ 20.310598] Registered led device: phy0-led [ 20.310628] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.372306] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 20.411015] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 20.454232] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11 [ 20.545636] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.545640] cfg80211: World regulatory domain updated: [ 20.545642] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.545644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545647] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545652] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545654] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.609484] type=1400 audit(1340502633.160:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=693 comm="apparmor_parser" [ 20.609494] type=1400 audit(1340502633.160:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=642 comm="apparmor_parser" [ 20.609843] type=1400 audit(1340502633.160:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser" [ 20.609852] type=1400 audit(1340502633.160:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=642 comm="apparmor_parser" [ 20.610047] type=1400 audit(1340502633.160:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser" [ 20.610060] type=1400 audit(1340502633.160:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=642 comm="apparmor_parser" [ 20.610476] type=1400 audit(1340502633.160:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=814 comm="apparmor_parser" [ 20.610829] type=1400 audit(1340502633.160:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=814 comm="apparmor_parser" [ 20.611035] type=1400 audit(1340502633.160:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=814 comm="apparmor_parser" [ 20.661912] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 20.661982] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [ 20.662013] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 20.770289] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 20.770689] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 20.770786] snd_hda_intel 0000:01:00.1: irq 48 for MSI/MSI-X [ 20.770815] snd_hda_intel 0000:01:00.1: setting latency timer to 64 [ 20.994040] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 20.994189] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13 [ 21.554799] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [ 21.554802] vesafb: scrolling: redraw [ 21.554804] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 21.557342] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011800000, using 3072k, total 3072k [ 21.557498] Console: switching to colour frame buffer device 128x48 [ 21.557516] fb0: VESA VGA frame buffer device [ 21.987338] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 22.184693] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 27.362440] iwlwifi 0000:04:00.0: RF_KILL bit toggled to disable radio. [ 27.436988] init: failsafe main process (986) killed by TERM signal [ 27.970112] ppdev: user-space parallel port driver [ 28.198917] Bluetooth: Core ver 2.16 [ 28.198935] NET: Registered protocol family 31 [ 28.198937] Bluetooth: HCI device and connection manager initialized [ 28.198940] Bluetooth: HCI socket layer initialized [ 28.198941] Bluetooth: L2CAP socket layer initialized [ 28.198947] Bluetooth: SCO socket layer initialized [ 28.226135] Bluetooth: RFCOMM TTY layer initialized [ 28.226141] Bluetooth: RFCOMM socket layer initialized [ 28.226143] Bluetooth: RFCOMM ver 1.11 [ 28.445620] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 28.445623] Bluetooth: BNEP filters: protocol multicast [ 28.524578] type=1400 audit(1340502641.076:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1052 comm="apparmor_parser" [ 28.525018] type=1400 audit(1340502641.076:12): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1052 comm="apparmor_parser" [ 28.629957] type=1400 audit(1340502641.180:13): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1105 comm="apparmor_parser" [ 28.630325] type=1400 audit(1340502641.180:14): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1105 comm="apparmor_parser" [ 28.630535] type=1400 audit(1340502641.180:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1105 comm="apparmor_parser" [ 28.645266] type=1400 audit(1340502641.196:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1104 comm="apparmor_parser" **[ 28.751922] ADDRCONF(NETDEV_UP): wlan0: link is not ready** [ 28.753653] tg3 0000:08:00.0: irq 49 for MSI/MSI-X **[ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 28.857034] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 28.871080] type=1400 audit(1340502641.420:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1108 comm="apparmor_parser" [ 28.871519] type=1400 audit(1340502641.420:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1108 comm="apparmor_parser" [ 28.874905] type=1400 audit(1340502641.424:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1113 comm="apparmor_parser" [ 28.875354] type=1400 audit(1340502641.424:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1113 comm="apparmor_parser" [ 30.477976] tg3 0000:08:00.0: eth0: Link is up at 100 Mbps, full duplex [ 30.477979] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX **[ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready** [ 31.110269] fglrx_pci 0000:01:00.0: irq 50 for MSI/MSI-X [ 31.110859] [fglrx] Firegl kernel thread PID: 1327 [ 31.111021] [fglrx] Firegl kernel thread PID: 1329 [ 31.111408] [fglrx] Firegl kernel thread PID: 1330 [ 31.111543] [fglrx] IRQ 50 Enabled [ 31.712938] [fglrx] Gart USWC size:1224 M. [ 31.712941] [fglrx] Gart cacheable size:486 M. [ 31.712945] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 31.712948] [fglrx] Reserved FB block: Unshared offset:fc2b000, size:3d5000 [ 31.712950] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [ 41.312020] eth0: no IPv6 routers present As you can see I get multiple instances of [ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready and then finally it becomes read and I get the message [ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready. I searched askubuntun, ubuntuforum, and the web but couldn't find a solution. Any help would be very much appreciated. Here is the bootchart

  Read the article

• Suspending my laptop breaks ethernet over firewire, are there commands which can fix it?

  - by Josh

  As mentioned in this question I am using a firewire cable to provide a private network between my laptop and my desktop, because it makes using the screen sharing program synergy much nicer than using WIFI. However when I leave my office for the day and I suspend my laptop, when I return the next day, the desktop and the laptop cannot communicate over firewire anymore. The firewire0 device still has an IP address. but when I try and ping the desktop I get no route to host I'm using kernel 2.6.35-24-generic #42-Ubuntu SMP x86_64 on Ubuntu 10.10. Is there some way I can remedy this without a reboot? Like, removing some kernel modules and re-inserting them? Here's what I have tried so far and the results: root@token:~# dmesg|tail -n 1 [592525.204024] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 root@token:~# modprobe -r firewire_net firewire_ohci firewire_core root@token:~# modprobe -v firewire_ohci insmod /lib/modules/2.6.35-24-generic/kernel/lib/crc-itu-t.ko insmod /lib/modules/2.6.35-24-generic/kernel/drivers/firewire/firewire-core.ko insmod /lib/modules/2.6.35-24-generic/kernel/drivers/firewire/firewire-ohci.ko root@token:~# dmesg|tail [592525.204024] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592563.410868] firewire_ohci: Removed fw-ohci device. [592579.160086] firewire_ohci: Added fw-ohci device 0000:02:00.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2 [592579.160137] firewire_ohci: isochronous cycle inconsistent [592579.660294] firewire_core: created device fw0: GUID 0000000000000000, S400 [592579.663805] firewire_core: created device fw1: GUID 0017f2fffe89bce6, S400 [592579.663813] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592579.700720] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592579.700842] firewire_core: refreshed device fw0 [592579.702603] firewire_net: firewire0: IPv4 over FireWire on device 0000000000000000 root@token:~# ping stan.firewire PING stan.firewire (192.168.100.1) 56(84) bytes of data. From token.local (192.168.100.3) icmp_seq=1 Destination Host Unreachable From token.local (192.168.100.3) icmp_seq=2 Destination Host Unreachable From token.local (192.168.100.3) icmp_seq=3 Destination Host Unreachable I also tried removing the modules prior to suspending, and re-inserting after resuming. This did not work either :-(

  Read the article

• Pluscom MAC address shows up but "wireless unavailable"

  - by Luigi

  I've got a pluscom pci card plugged into my desktop and although the mac address shows up in network manager, it says "Wireless unavailable". I'm using Ubuntu 12.10 Gnome Shell Remix... edgar@edgarQuantal:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off edgar@edgarQuantal:~$ ifconfig eth0 Link encap:Ethernet HWaddr 6c:f0:49:02:1f:b8 inet addr:192.168.0.7 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fe02:1fb8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1425 errors:0 dropped:0 overruns:0 frame:0 TX packets:1393 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:995753 (995.7 KB) TX bytes:134079 (134.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:363 errors:0 dropped:0 overruns:0 frame:0 TX packets:363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:40828 (40.8 KB) TX bytes:40828 (40.8 KB) It looks the same as the problem as here, seems quite complicated: http://ubuntuforums.org/showthread.php?t=1993226 Tried downloading the driver but i get this: "Unpacking firmware-ralink (from .../firmware-ralink_0.36_all.deb) ... dpkg: error processing /home/edgar/Downloads/firmware-ralink_0.36_all.deb (--install): trying to overwrite '/lib/firmware/rt2870.bin', which is also in package linux-firmware 1.95"

  Read the article

• Unable to set default gateway

  - by GrandMasterFlush

  I'm running Ubuntu server via Hyper-V and have successfully installed it but seem unable to ping the server or ping any other machines on the network from the server. After doing a bit of reading I've noticed that the default gateway isn't set but when I try and set it I keep getting error messages which I can't understand. From this article I've tried ip route add default via 10.0.10.200 Which reports: RTNETLINK answers: Operation not permitted If I try running it prefixed with sudo but it reports: `RNETLINK answers: No such process I've editted /etc/network/interfaces but when I start the machine and type netstat -nr there is nothing listed. Can anyone tell me where I'm going wrong please? EDIT : /etc/network/interfaces contains: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp

  Read the article

• Nice network diagram editor?

  - by Nicolas Raoul

  Writing a commercial proposal, I want to create a nice graphic showing the clients the architecture I thought of for their IT network, with servers, network connections, firewall, load-balancing, etc. For years I have been using dia, but I am tired of it because: the results are not satisfying, very few network elements are available, and each element's graphic representation is really ugly. Question: How to create nice network diagrams? If a better set of elements was available for dia, that would be a solution.

  Read the article

< Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >