Search Results

Search found 2863 results on 115 pages for 'sms gateway'.

Page 75/115 | < Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >

• Implementing a form of port knocking + Phone Factor = 2 Factor auth for RDP?

  - by jshin47

  I have been looking into how to secure a publicly-available RDP endpoint and want to implement our two-factor authentication RADIUS server, PhoneFactor. I would like to implement the following process: User opens up web app in browser In web app, user enters username + password, initiates RADIUS auth Phone factor calls user to complete auth Once user is authenticated, port 3389 is opened on user's IP on pfSense firewall. After some amount of time, firewall rule is removed for that IP I would like to know the following: Is this a typical setup? If it is a bad idea, please explain why. If it is possible, are there any packages that assist with this? Specifically, the third step, where the appropriate firewall rule would need to be added... Edit: I am aware of TS Web Gateway, but I want the users to be able to use the traditional RDP client...

  Read the article

• XenServer VM's lose network settings

  - by Ash

  We deploy virtual machines using Citrix XenServer 6.0 for our clients. Two seperate clients experience the same issue: when a Server 2008 virtual machine is restarted, the static IP addresses (network address, subnet, gateway, primary DNS) don't appear to apply correctly as the IP's cannot be pinged, network services cannot be accessed etc. The issue is resolved by manually switching the network adapters to DHCP, then re-setting them to the original static IP's. While not a major issue, it's a pain when restarting servers due to Windows Updates, plus iSCSI drives need to be manually connected to Windows again via iSCSI Initiator. We have tried removed the network adapters from the virtual machine under XenCentre but without luck. Anyone experienced similar issues?

  Read the article

• Automatically generated /etc/hosts is wrong

  - by Niels Basjes

  I've created a kickstart script to install CentOS 5.5 (32bit) in a fully automated way. The DNS/DHCP setup correctly gives the system the right hostname in both the forward and reverse lookups. dig node4.mydomain.com. +short 10.10.10.64 dig -x 10.10.10.64 +short node4.mydomain.com. In the state the installed system is right after the installation completed is as follows: cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=yes GATEWAY=10.10.10.1 HOSTNAME=node4.mydomain.com echo ${HOSTNAME} node4.mydomain.com cat /etc/hosts # Do not remove the following line, or various programs # that require network functionality will fail. 127.0.0.1 localhost.localdomain localhost ::1 localhost6.localdomain6 localhost6 10.10.10.64 node4 My problem is that this automatically generated hosts file is slightly different from the way I want it (or better: the way Hadoop wants it). The last line should look like this: 10.10.10.64 node4.mydomain.com node4 What do I modify where to fix this? Thanks.

  Read the article

• Debian 6 Internet connection sharing aka IP masquerade not working

  - by Rautamiekka

  The problem: the computers [Xbox 360 and a Kubuntu 12.04.1 laptop] can't access Internet through a recently-installed desktopless Debian 6 laptop (which is wirelessly connected to a WLAN station) but addresses are successfully given by dnsmasq. The attempts: 1.1) /etc/dnsmaq.conf conffed according to http://wiki.debian.org/HowTo/dnsmasq: add lines interface=eth0 dhcp-range=192.168.0.50,192.168.0.150,255.255.255.0,12h 1.2) Follow http://www.cyberciti.biz/faq/rhel-fedora-linux-internet-connection-sharing-howto/ and use their script to setup iptables. 2) Follow the Ubuntu Internet Gateway Method (iptables) at https://help.ubuntu.com/community/Internet/ConnectionSharing recommended and which worked at Share internet in Linux. The Debian laptop was rebooted many times and between each attempt, with and without the script auto-executing via /etc/rc.local. While adding the iptables-restore command to that file I disabled the script.

  Read the article

• Why is my eth0 getting a dynamic ip when it is configured to be static?

  - by sdek

  For some reason our office linux box is being assigned an ip address via dhcp and I don't know why. What is confusing to me is that when I check system-config-network it shows that my eth0 is setup to be a static ip address. And /etc/sysconfig/network-scripts/ifcfg-eth0 also shows it is setup to be a static ip, yet it is getting a different ip address than the one specified in the ifcfg-eth0. Let me know if you have any suggestions on or ideas on where I can look next. Here are a few details that might help you figure out what an idiot I am :) Fedora 11 Router in front of this box is running dhcp, starting at 10.42.1.100 This box is configured to be 10.42.1.50 (at least I think it is!), subnet 255.255.255.0 (which is same as the router's lan subnet) Instead of having the static IP, this box is getting assigned 10.42.1.100. Here are the ifcfg-eth0 details DEVICE=eth0 BOOTPROTO=none ONBOOT=yes TYPE=Ethernet USERCTL=no NM_CONTROLLED=no NETMASK=255.255.255.0 IPADDR=10.42.1.50 GATEWAY=10.42.1.1

  Read the article

• GNS3 Cannot ping/resolve DNS record

  - by Eldad Cohen

  I set up an internet lab with GNS3, which has 3 routers, in each node there is a computer directly connected. One of the hosts is a DNS server, Windows 2003 Server. The other one is a Windows XP machine. Ping is good between routers and machines but no ability to ping domain.com record on DNS server 2003. I set a static nat on the router to route all traffic from gateway to the DNS server internal ip address, still no answer for the dns request. Any ideas or thoughts will be most welcome.

  Read the article

• dhclient configures /etc/resolv.conf with invalid entry

  - by kubal5003

  I'm trying to figure out why running dhclient on my interface sets /etc/resolv conf to the ip number of my gateway(router). This entry is invalid and each and every time causes inability to resolve any address. I would like to: stop dhclient from overwriting the /etc/resolv.conf or make dhclient write there the valid dns ip from my router More on the environment: I'm using virtual Debian Wheezy as a client system on Windows Seven x64. It is run by Virtualbox with networking mode set to bridged (all packets from debian are injected to my network interface on windows). If I manually configure the /etc/resolv.conf then everything works fine. Doing this on every boot is quite annoying.. PS I know I can write a script to do it for me, but this is not the solution I want. //edit router ip: 192.168.1.100 /etc/resolv.conf AFTER running dhclient eth0: "nameserver 192.168.1.100" what I would like the /etc/resolv.conf to look like: "nameserver 89.202.xxxx" (I don't have to provide the real ip do I? )

  Read the article

• Belking Wireless Router unable to connect to internet although wireless connection is working

  - by ptamzz

  I have a Belkin Basic N150 Wireless router. I'm trying to set up wireless connection using the wired ports my university has provided in my hostel room. Usually, when I connect my laptop using a LAN wire through the port, my settings are like IP: 10.5.130.X Subnet Mask: 255.255.254.0 Default Gateway: 10.5.130.250 DNS Server: 10.200.1.11 and I'm able to connect to the internet. Now instead of connecting my laptop directly, I've connected the lan wire to the Belkin Wireless Router, set the router as "Use as an Access Point" and in the IP field, I've put up 10.5.130.1. Now I've set the IP of my system manually to 10.5.130.3. I'm able to connect to the wi-fi but I'm still not able to connect to the internet. What am I missing?

  Read the article

• How can I log all traffic with its exact length?

  - by Legate

  I want to process all packets with their size going through our gateway server (running Debian 4.0). My idea is to use tcpdump, but I have two questions. The command I'm currently thinking of is tcpdump -i iface -n -t -q. Is it guaranteed that tcpdump will process all packets? What happens if the CPU is working to full capacity? The format of the output lines is IP ddd.ddd.ddd.ddd.port > ddd.ddd.ddd.ddd.port: tcp 1260. What exactly is 1260? I have the suspicion that it is the payload in bytes of the packet, which would be exactly what I need, but I'm not sure. It might be the TCP Window Size. Or perhaps there is an even better way of doing this? I thought about a LOG rule in iptables, but tcpdump seems easier and I don't know whether iptables can log the packet lengths.

  Read the article

• KVM Guest not reachable from host

  - by Paul

  Hello, I'm running Ubuntu server 9.10, installed KVM etc. Created the bridge network following instructions on help.ubuntu.com/community/KVM/Networking Created a windows 2008 guest using virt-install command line (using virt-manager GUI from a remote Ubuntu desktop would not let me select the ISO location). I can however use a remote virt-manager to connect to the guest and complete the windows install. Within windows 2008 I changed the IP address but cannot ping from outside world. The bridge network appears fine - I'm not sure what else to look at! Here is the interfaces file: The loopback network interface auto lo iface lo inet loopback The primary network interface auto eth0 iface eth0 inet manual # auto br0 iface br0 inet static address 60.234.64.50 netmask 255.255.255.248 network 60.234.0.0 broadcast 60.234.0.255 gateway 60.234.64.49 bridge_ports eth0 bridge_stp off bridge_fd 0 bridge_maxwait 0 auto eth1 iface eth1 inet static address 192.168.12.2 netmask 255.255.255.0 broadcast 192.168.12.255 The ip of the windows server is 60.234.64.52 What else should I check? Regards Paul.

  Read the article

• How to configure remote access to multiple subnets behind a SonicWALL NSA 2400

  - by Kyle Noland

  I have a client that uses a SonicWALL NSA 2400 as their firewall. I need to setup a second LAN subnet for a handful of PC. Management has decided that there should be a second subnet even though intend to allow access across the two subnets - I know... I'm having trouble getting communication across the 2 subnets. I can ping each gateway, but I cannot ping or seem to route traffic fron subnet A to subnet B. Here is my current setup: X0 Interface: LAN zone with IP addres 192.168.1.1 X1 Interface: WAN zone with WAN IP address X2 Interface: LAN zone with IP address 192.168.75.1 I have configured ARP and routes for the secondar subnet (X2) according to this SonicWALL KB article: http://www.sonicwall.com/downloads/supporting_multiple_firewalled_subnets_on_sonicos_enhanced.pdf using "Example 1". At this point I don't minding if I have to throw the SonicWALL GVC software VPN client into the mix to make it work. It feel like I have an Access Rule issue, but for testing I made LAN LAN, WAN LAN and VPN LAN rules wide open with the same results.

  Read the article

• Recover from running "route -f"

  - by James L.

  I was trying to capture localhost traffic with Ethereal, which doesn't work without re-routing localhost traffic to your router gateway. I didn't get the route command quite right, and messed up my routing table. I typed route -f to clear the routing table and rebooted, but when I finished rebooting, the routing table wasn't restored to its original state. I didn't use the -p parameter, so none of my changes should have persisted after a reboot. What can I do to restore the routing table to its default routes?

  Read the article

• Redhat doesn't set my desired hostname on reboot

  - by tomdee

  I have a redhat (EL5) server that I need to change the hostname on. I'm trying to put it back into a known state to help with server provisioning activities. As part of changing the hostname, I'm updating /etc/sysconfig/network and /etc/hosts. I also have an explicit call to hostname. My desired state is that the server thinks its hostname is "localhost". And a call to "hostname" returns "localhost". The problem I'm having is that when I reboot, the hostname is reverted to "localhost.companyname.com" which is not what I want. How do I ensure that the hostname is set up as just "localhost" when I reboot? My /etc/sysconfig/network file contains: NETWORKING=yes HOSTNAME=localhost GATEWAY=123.123.123.123 #I do have a proper IP address here My /etc/hosts file contains: 127.0.0.1 localhost.localdomain localhost 172.21.1.1 localhost.companyname.com localhost

  Read the article

• Disabling at application level a nic (network interface) on Windows

  - by Leandro

  How can I disable at application level a network interface? The main question is this: If I disable the nic trough wmic (win7) or devcon (XP), the "plug and play" of a wired nic doesn't work any more. For example, if the user put the cable on a disabled nic, the OS doesn't know about it. So I need to persist the enable condition but disabling the networking like a disable nic. There's some API, network configuration (routing, changing ip, changing gateway, any), .NET Framework resource (Only NetFramework 2.0) or do you can think in any workaround to do this? Suggest and ideas also will be treated as a solution. Thanks and kind regards.

  Read the article

• How do I delete a route in OS X 10.5

  - by authormichael-olsen-craig

  I somehow configured my Mac to route all requests for a particular IP Name (sample.com) to the loopback address (127.0.0.1). Now I'm trying to remove this, but can't determine where to do it. There is no entry for it under /etc/hosts. The routing table shows that it is mapping the IP Name to the IP address of the Mac. Routing table output below: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.2.1 UGSc 4 1 en0 127 sample.com UCS 0 0 lo0 sample.com sample.com UH 1 7093 lo0 169.254 link#4 UCS 0 0 en0 192.168.2 link#4 UCS 6 0 en0 192.168.2.1 0:11:22:22:3f:fa UHLW 20 55565 en0 1070 192.168.2.15 tsema.org UHS 0 9 lo0 192.168.2.255 link#4 UHLWb 4 84777 en0 Any help would be greatly appreciated!

  Read the article

• CentOS: eth0 not starting on boot

  - by Cameron Aziz

  Whenever I reboot a CentOS Hyper-V VM, eth0 does not start automatically. All I need to do is perform ifup eth0 and all is fixed, but that isn't feasible from ssh! I am starting in runlevel 3. After I perform ifup eth0 on the console: [root@localhost ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:15:5D:2B:2B:07 inet addr:10.10.0.3 Bcast:10.10.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe2b:2b07/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:49 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4656 (4.5 KiB) TX bytes:6399 (6.2 KiB) Interrupt:9 Base address:0xa000 [root@localhost ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none IPADDR=10.10.0.3 NETMASK=255.255.255.0 GATEWAY=10.10.0.1 USERCTL=no ONBOOT=yes [root@localhost ~]# chkconfig --list | grep network network 0:off 1:off 2:on 3:on 4:on 5:on 6:off

  Read the article

• Packet loss with all adapters on one PC only on the LAN

  - by Enigmativity

  I have a Windows 7 64-bit machine that is losing up to 20% of IP packets on both adapters - wireless & LAN. Browser traffic appears to be affected the most, but it is happening to all protocols. All other computers on the network are functioning fine. If I ping from my faulty machine to any machine on the LAN (wired or wirelessly), including the router/gateway and internet sites, I get up to 20% packet loss. If I do the following commands: ipconfig /release ipconfig /renew then I sometimes get my network performance back for a matter of a few seconds to less than a couple of minutes. Rebooting also works for a short period of time. This problem has been occurring for a couple of months and is getting worse. The computer used to work just fine. I updated the wireless adapter firmware the other day with no effect. Does anyone know what is happening?

  Read the article

• IPTables masquerading with one NIC

  - by Tuinslak

  Hi, I am running an OpenVPN server with only one NIC. This is my current layout: public.ip > Cisco firewall > lan.ip > OpenVPN server lan.ip = 192.168.22.70 The Cisco firewall forwards the requests to the oVPN server, thus so far everything works and clients are able to connect. However, all clients connected should be able to access 3 networks: lan1: 192.168.200.0 (vpn lan) > tun0 lan2: 192.168.110.0 (office lan) > eth1 (gw 192.168.22.1) lan3: 192.168.22.0 (server lan) > eth1 (broadcast network) So tun0 is mapped to eth1. Iptables output: # iptables-save # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *filter :INPUT ACCEPT [327:26098] :FORWARD DROP [305:31700] :OUTPUT ACCEPT [291:27378] -A INPUT -i lo -j ACCEPT -A INPUT -i tun0 -j ACCEPT -A INPUT -i ! tun0 -p udp -m udp --dport 67 -j REJECT --reject-with icmp-port-unreachable -A INPUT -i ! tun0 -p udp -m udp --dport 53 -j REJECT --reject-with icmp-port-unreachable -A FORWARD -d 192.168.200.0/24 -i tun0 -j DROP -A FORWARD -s 192.168.200.0/24 -i tun0 -j ACCEPT -A FORWARD -d 192.168.200.0/24 -i eth1 -j ACCEPT COMMIT # Completed on Wed Feb 16 14:14:20 2011 # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *nat :PREROUTING ACCEPT [302:26000] :POSTROUTING ACCEPT [3:377] :OUTPUT ACCEPT [49:3885] -A POSTROUTING -o eth1 -j MASQUERADE COMMIT # Completed on Wed Feb 16 14:14:20 2011 Yet, clients are unable to ping any ip (including 192.168.200.1, which is the oVPN's IP) When the machine was directly connected to the internet, with 2 NICs, it was quite simply solved with masquerading and adding static routes in the oVPN client's config. However, as masquerading won't accept virtual interfaces (eth0:0, etc) I am unable to get masquerading to work again (and I'm not even sure whether I need virtual interfaces). Thanks. Edit: OpenVPN server: # ifconfig eth1 Link encap:Ethernet HWaddr ba:e6:64:ec:57:ac inet addr:192.168.22.70 Bcast:192.168.22.255 Mask:255.255.255.0 inet6 addr: fe80::b8e6:64ff:feec:57ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6857 errors:0 dropped:0 overruns:0 frame:0 TX packets:4044 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:584046 (570.3 KiB) TX bytes:473691 (462.5 KiB) Interrupt:14 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:33773 (32.9 KiB) TX bytes:33773 (32.9 KiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.1 P-t-P:192.168.200.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifconfig on a client: # ifconfig eth0 Link encap:Ethernet HWaddr 00:22:64:71:11:56 inet addr:192.168.110.94 Bcast:192.168.110.255 Mask:255.255.255.0 inet6 addr: fe80::222:64ff:fe71:1156/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3466 errors:0 dropped:0 overruns:0 frame:0 TX packets:1838 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:997924 (974.5 KiB) TX bytes:332406 (324.6 KiB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:37847 errors:0 dropped:0 overruns:0 frame:0 TX packets:37847 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2922444 (2.7 MiB) TX bytes:2922444 (2.7 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.30 P-t-P:192.168.200.29 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:689 errors:0 dropped:18 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:468778 (457.7 KiB) wlan0 Link encap:Ethernet HWaddr 00:16:ea:db:ae:86 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:704699 errors:0 dropped:0 overruns:0 frame:0 TX packets:730176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:520385963 (496.2 MiB) TX bytes:225210422 (214.7 MiB) static routes line at the end of the client's config (I've been playing around with the 192.168.200.0 -- (un)commenting to see if anything changes): route 192.168.200.0 255.255.255.0 route 192.168.110.0 255.255.255.0 route 192.168.22.0 255.255.255.0 route on a vpn client: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.200.29 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.22.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.200.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.110.1 0.0.0.0 UG 0 0 0 eth0 edit: Weirdly enough, if I set push "redirect-gateway def1" in the server config, (and thus routes all traffic through VPN, which is not what I want), it seems to work.

  Read the article

• Weird behaviour with OpenVPN: can not connect to a few websites

  - by Gaby Solis

  My OpenVPN server is Ubuntu 10.04.4 LTS and openvpn version is 2.x My client is on Win 7. He can access most sites but not Youtube, Facebook, Twitter, groups.google.com, etc My server.conf is: local x.x.x.x port 1194 proto udp dev tun ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/server.crt key /etc/openvpn/keys/server.key dh /etc/openvpn/keys/dh1024.pem server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" push "dhcp-option DNS 8.8.8.8" client-to-client keepalive 10 120 comp-lzo persist-key persist-tun status /etc/openvpn/keys/openvpn-status.log verb 4 I can access Youtube etc using SSH Tunnel + SOCKS Proxy, and the Ubuntu server can access all sites. so nothing is wrong with the Ubuntu server. With little information I can provide, I am not looking for a quck solution. How can I debug?

  Read the article

• SQL Server 2008 R2 100% availability

  - by Mark Henderson

  Is there any way to provide 100% uptime on SQL Server 2008 R2? From my experience, the downtimes for the different replication methods are: Log Shipping: Lots (for DR only) Mirroring w. NLB: ~ 45 seconds Clustering: ~ 5-15 seconds And all of these solutions involve all of the connections being dropped from the source, so if the downtime is too long or the app's gateway doesn't support reconnection in the middle of task, then you're out of luck. The only way I can think to get around this is to abstract the clustering a level (by virtualising and then enabling VMWare FT. Yuck. Good luck getting this to work on a quad-socket, 32-core system anyway.). Is there any other way of providing 100% uptime of SQL Server?

  Read the article

• Is there any viable alternative to using a linux/unix/BSD firewall/router/vpn?

  - by ObligatoryMoniker

  I am trying to purchase something to replace our Vyatta router that is running in a virtual machine on Hyper V (having the whole network go down when the host has to reboot is not convenient and I am getting the sense that this configuration may not be stable). Most posts on this topic suggest using Linux/OpenBSD/FreeBSD/etc with some recommendations to use appliances from vendors for specific purposes like firewall and VPN. We are a windows shop and it has been a stretch for us to make use of Vyatta but since it was free and straightforward to use we decided to use it. Now we need something that is easier for our team to (re)deploy and manage. I would rather purchase something windows based or an appliance that can do all of the following things: DHCP server (reservations, specified gateway, dns, etc) Static Routes that route traffic across three interfaces Easily Reproducible (Powershell script, Puppet, Chef, etc) Intuitive interface (Decent web interface would be fine but I don't want them to have to go to CLI) Does any one have any recommendations on what I should be looking at that might meet our needs?

  Read the article

• Management VLAN Cisco Catalyst

  - by cha789

  I have configured a couple of VLANs on a Cisco Catalyst switch, i will put all the ports that clients is connected to, into these VLANs. I want to configure the native VLAN [vlan 1] as management VLAN so i can use a telnet client to connect to the switch. How can i block all but one specific IP-address to telnet into the switch? As i understand vlan 1 has many task regarding different protocols and i do not want to break that but only allow one specific IP-address to connect to the switch with a telnet client [actually the gateway ip address of the switch].

  Read the article

• How to monitor the network traffic on a router?

  - by Adi

  Here's my current network set-up: we have 3 users connecting to a Thomson Gateway router (TG585 v8) provided by my ISP. We are connecting over an ADSL line. The problem is that we have a limited data allowance (60GB) and we always exceed it. I would like to monitor how much traffic each computer makes. The best solution would be to install a software on the router (like OpenWRT) which would monitor how much traffic each computer makes. But I couldn't find any replacement firmware that would support my router. The other solution would be to install a software on each machine and then collect all the data at the end of the mount. But that's not a very good think to do. Plus, the users can always shut down the application. Any suggestions?

  Read the article

• How can I access the external microphone with Ubuntu?

  - by Charles Merriam

  Sound in Ubuntu, it has its own special joy. I would like my external microphone to work. Symptoms: I can play sound through the speakers I can play sound through the headsets. Plugging and and plugging headphone output correctly switches. I can record from the built-in microphone, using "Sound Recorder" and others. but: I cannot record from the external microphone. My Sound Preferences/Input panel has no option for an external microphone. If the answer is upgrade the ALSA drivers, please say exactly what to type. Thank you. ======== I'm using Ubuntu 9.10 Karmic Koala on a laptop (Gateway W3501), Sigmatel. That is: ~$ head -1 /proc/asound/card0/code* ==> /proc/asound/card0/codec#0 <== Codec: SigmaTel STAC9205 ==> /proc/asound/card0/codec#1 <== Codec: Conexant ID 2c06 ~$ lspci | grep -i audio 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)

  Read the article

• BugZilla XML RPC Interface

  - by Damo

  I am attempting to setup BugZilla to receive but reports from another system using the XML-RPC interface. BugZilla works fine on its own with its own interface. When I attempt to test the XML-RPC functionality by accessing "xmlrpc.cgi" in my browser I get the error: The XML-RPC Interface feature is not available in this Bugzilla at C:\BugZilla\xmlrpc.cgi line 27 main::BEGIN(...) called at C:\BugZilla\xmlrpc.cgi line 29 eval {...} called at C:\BugZilla\xmlrpc.cgi line 29 Following this I install test-taint package from the default perl repository, this installs version 1.04. Re-running "xmlrpc.cgi" gives me an IIS error: 502 - Web server received an invalid response while acting as a gateway or proxy server. There is a problem with the page you are looking for, and it cannot be displayed. When the Web server (while acting as a gateway or proxy) contacted the upstream content server, it received an invalid response from the content server. So I run the checksetup.pl which inform me that: Use of uninitialized value in open at C:/Perl/site/lib/Test/Taint.pm line 334, <DATA> line 558. Installing Test-Taint from CPAN is the same. I assume XML-RPC is relent on Test-Taint, but Test-Taint doesn't seem to run correctly. If I ignore this error and attempt to invoke "bz_webservice_demo.pl" to add an entry the script times out. How can I get the XML-RPC / Test-Taint function working ? Current Setup: IIS7.5 on Windows Server 2008 Bugzilla 4.2.2 Perl 5.14.2 C:\BugZilla>perl checksetup.pl Set up gcc environment - 3.4.5 (mingw-vista special r3) * This is Bugzilla 4.2.2 on perl 5.14.2 * Running on Win2008 Build 6002 (Service Pack 2) Checking perl modules... Checking for CGI.pm (v3.51) ok: found v3.59 Checking for Digest-SHA (any) ok: found v5.62 Checking for TimeDate (v2.21) ok: found v2.24 Checking for DateTime (v0.28) ok: found v0.76 Checking for DateTime-TimeZone (v0.79) ok: found v1.48 Checking for DBI (v1.614) ok: found v1.622 Checking for Template-Toolkit (v2.22) ok: found v2.24 Checking for Email-Send (v2.16) ok: found v2.198 Checking for Email-MIME (v1.904) ok: found v1.911 Checking for URI (v1.37) ok: found v1.59 Checking for List-MoreUtils (v0.22) ok: found v0.33 Checking for Math-Random-ISAAC (v1.0.1) ok: found v1.004 Checking for Win32 (v0.35) ok: found v0.44 Checking for Win32-API (v0.55) ok: found v0.64 Checking available perl DBD modules... Checking for DBD-Pg (v1.45) ok: found v2.18.1 Checking for DBD-mysql (v4.001) ok: found v4.021 Checking for DBD-SQLite (v1.29) ok: found v1.33 Checking for DBD-Oracle (v1.19) ok: found v1.30 The following Perl modules are optional: Checking for GD (v1.20) ok: found v2.46 Checking for Chart (v2.1) ok: found v2.4.5 Checking for Template-GD (any) ok: found v1.56 Checking for GDTextUtil (any) ok: found v0.86 Checking for GDGraph (any) ok: found v1.44 Checking for MIME-tools (v5.406) ok: found v5.503 Checking for libwww-perl (any) ok: found v6.02 Checking for XML-Twig (any) ok: found v3.41 Checking for PatchReader (v0.9.6) ok: found v0.9.6 Checking for perl-ldap (any) ok: found v0.44 Checking for Authen-SASL (any) ok: found v2.15 Checking for RadiusPerl (any) ok: found v0.20 Checking for SOAP-Lite (v0.712) ok: found v0.715 Checking for JSON-RPC (any) ok: found v0.96 Checking for JSON-XS (v2.0) ok: found v2.32 Use of uninitialized value in open at C:/Perl/site/lib/Test/Taint.pm line 334, <DATA> line 558. Checking for Test-Taint (any) ok: found v1.04 Checking for HTML-Parser (v3.67) ok: found v3.68 Checking for HTML-Scrubber (any) ok: found v0.09 Checking for Encode (v2.21) ok: found v2.44 Checking for Encode-Detect (any) not found Checking for Email-MIME-Attachment-Stripper (any) ok: found v1.316 Checking for Email-Reply (any) ok: found v1.202 Checking for TheSchwartz (any) not found Checking for Daemon-Generic (any) not found Checking for mod_perl (v1.999022) not found Checking for Apache-SizeLimit (v0.96) not found *********************************************************************** * OPTIONAL MODULES * *********************************************************************** * Certain Perl modules are not required by Bugzilla, but by * * installing the latest version you gain access to additional * * features. * * * * The optional modules you do not have installed are listed below, * * with the name of the feature they enable. Below that table are the * * commands to install each module. * *********************************************************************** * MODULE NAME * ENABLES FEATURE(S) * *********************************************************************** * Encode-Detect * Automatic charset detection for text attachments * * TheSchwartz * Mail Queueing * * Daemon-Generic * Mail Queueing * * mod_perl * mod_perl * * Apache-SizeLimit * mod_perl * *********************************************************************** COMMANDS TO INSTALL OPTIONAL MODULES: Encode-Detect: ppm install Encode-Detect TheSchwartz: ppm install TheSchwartz Daemon-Generic: ppm install Daemon-Generic mod_perl: ppm install mod_perl Apache-SizeLimit: ppm install Apache-SizeLimit Reading ./localconfig... OPTIONAL NOTE: If you want to be able to use the 'difference between two patches' feature of Bugzilla (which requires the PatchReader Perl module as well), you should install patchutils from: http://cyberelk.net/tim/patchutils/ Checking for DBD-mysql (v4.001) ok: found v4.021 Checking for MySQL (v5.0.15) ok: found v5.5.27 WARNING: You need to set the max_allowed_packet parameter in your MySQL configuration to at least 3276750. Currently it is set to 3275776. You can set this parameter in the [mysqld] section of your MySQL configuration file. Removing existing compiled templates... Precompiling templates...done. checksetup.pl complete.

  Read the article

< Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >