Search Results

Search found 2333 results on 94 pages for 'x64'.

Page 75/94 | < Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >

• Computer sponteously reboots when doing heavy file copy to/from disk

  - by Mark Hosang

  I've been fighting with this problem for the last 3 weeks where my machine will just instantly reboot. No BSOD, and when i checked the event log all that was reported was the generic "Kernal-power" error with the detailed information pointing to a hard crash. This is a machine that was working for 18 months before these crashes started happening. When they started happening is after I added 3 HDs in a RAID-5, upped the memory to 12gb, moved to a new house, added a SSD and added about 5 case fans. I have thus eliminated the RAID, and determined that the SSD was not the cause (because it was still crashing even though the ssd wasn't connected). I've run memtest several times over night with no memory problems showing up. I've run IntelBurnTest to max out the cpu to see if it was a heat issue and at full tilt after 20 min it was only at 85C and the machine didn't crash. I also took a look at the voltages during this test, with a screenshot at the bottom of this post I've ruled out a software issue by reinstalling windows 7 ultimate x64 a total of 5 times, but even during that the install it crashes. Happens sometime during file copying at the beginning, or during uncompressing files, or sometimes during running windows update. The only discernible pattern i can see is that it seems to crash when hard disks might be spinning up or when they are accessed heavily from large file transfers. My current guess is that it is probably an issue with the MB, PSU or the power coming through the outlet. Any suggestions of what i could try to troubleshoot or what may be wrong? Specs PSU: Seasonic M12 700w Mem: 12gb CPU: i7-920 with stock heatsink MB: Asus P6T HDs: 3 green WD and 1 Corsair force 3 120b with 1.3.3 firmware Running full tilt voltages Idling Voltages

  Read the article

• Ubuntu 12.04/12.10 can't detect windows or any other partitions(Asus z77 UEFI BIOS)

  - by user971155

  I've recently completed tinkering my new pc(motherboard ASUS z77 with UEFI BIOS) and unfortunately not everything works quite well. After installing windows 7 ultimate on a single primary partition(SATA drive) I decided to allocate one more logical partition for additional needs. When I tried doing it with the manager - it said that it couldn't allocate requested size even though I certainly asked for much less than it was available. I thought that it might have been a windows issue and proceded to installing Ubuntu 12.10 x64. When the graphical interface loaded it showed me a message stating that it can't find any other operating system on the drive. When I used custom partioning option it showed me none of my current partions(including that with windows). However, when I boot with "Try Ubuntu" feature it does find them ! I find it weird though. Here's what the console present me with: ubuntu@ubuntu:~$ sudo os-prober /dev/sda1:Windows 7 (loader):Windows:chain ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00072b98 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 100020223 49906688 7 HPFS/NTFS/exFAT /dev/sda3 100022270 1250263039 575120385 5 Extended /dev/sda4 566669312 1250263039 341796864 83 Linux I also tried creating partitions from disk utility which results in error: , Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/sda, start=51211402240, size=1923000000, type=0x83 Entering MS-DOS parser (offset=0, size=640135028736) MSDOS_MAGIC found looking at part 0 (offset 1048576, size 104857600, type 0x07) new part entry looking at part 1 (offset 105906176, size 51104448512, type 0x07) new part entry looking at part 2 (offset 51211402240, size 588923274240, type 0x05) Entering MS-DOS extended parser (offset=51211402240, size=588923274240) readfrom = 51211402240 MSDOS_MAGIC found Exiting MS-DOS extended parser looking at part 3 (offset 290134687744, size 349999988736, type 0x83) new part entry Exiting MS-DOS parser MSDOS partition table detected containing partition table scheme = 1 got it Error: Can't have overlapping partitions. ped_disk_new() failed Here's what I get when I try to install the system i.stack.imgur.com/pjlb9.png, i.stack.imgur.com/g1lXN.png P.S. It's strange that I even can't create any more partitions neither with disk-utility nor with windows 7 native tools

  Read the article

• Remote connection to a Windows 2008 Server Web edition

  - by Lorenzo

  Hello I have just installed Windows 2008 web server to have a development/test site on my office. In the test network I only have 2 machines: Windows server 2008 Web Edition Vista x64 client machine with Visual Studio The client and the server are networked using a NETGEAR router. I have enabled Remote desktop on the server and when I try to connect to it within the Vista client I get the credential window as in the following screenshot. But even if I write the correct credentials I am not able to remote login on the server. Where am I doing wrong? Update 1 I have even tried to create a folder share on the server. But I am not able to access it for the same reason. User or password invalid it says. But this is impossible as I am logging in the server with the same credentials. Update 2 If I try to browse the network from the RDP client I receive a message saying that there are no server running Terminal Services in my network.... :O

  Read the article

• Extract and view Outlook contacts attachment sent to Gmail

  - by matt wilkie

  A friend forwarded a contact list to my gmail account from Outlook (2007 or 2010, not sure which). I can see there is an attachment in gmail but when I save it to my local drive it's just a plain text file containing the text This attachment is a MAPI 1.0 embedded message and is not supported by this mail system. If I use gmail's "show original message" it contains in part: This is a multipart message in MIME format. ------=_NextPart_000_0016_01CC6656.CE12F030 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit ------=_NextPart_000_0016_01CC6656.CE12F030 Content-Type: application/ms-tnef; name="winmail.dat" Content-Transfer-Encoding: base64 Content-Disposition: attachment; filename="winmail.dat" eJ8+Ih0VAQaQCAAEAAAAAAABAAEAAQeQBgAIAAAA5AQAAAAAAADoAAEIgAcAGAAAAElQTS5NaWNy b3NvZnQgTWFpbC5Ob3RlADEIAQgABQAEAAAAAAAAAAAAAQkABAACAAAAAAAAAAEDkAYASAgAACgA --8<---snip---8<-- GUC/9NKH95rABgMA/g8HAAAAAwANNP0/pQ4DAA80/T+lDvAm ------=_NextPart_000_0016_01CC6656.CE12F030-- How do I save the attached winmail.dat properly, and open the winmail.dat and extract the contact list? I'm running Windows 7 x64, but have access to an ubuntu linux vmware appliance if needed. I have Outlook 2010, but can't use it to connect directly to gmail as pop3 and imap are blocked by the corporate firewall.

  Read the article

• Windows 7 hangs after going into sleep a second time

  - by Brian Stephenson

  I've searched everywhere around Google and can't figure out why this is happening so I decide to ask here to see if anyone has a problem like this. Like it says in the title, whenever I sleep ONCE I'm able to wake the system, but going back to sleep again AFTER waking up for the first time results in it hanging on no input and no output, with the fan spinning as fast as possible and alot of heat being spewed out by the fan as well. I've tried various things like setting all USB Hub Root's to not get switched off for power saving, disabling USB selective suspend, disabling PCI-e link state power management, and even unplugging ALL USB devices and it wont wake up after the second attempt. And I've even waited up to a full hour of the CPU fan spinning loudly and it's still stuck trying to wake up. The only USB devices I use are a Microsoft USB Comfort Curve Keyboard 2000 (IntelliType Pro) and a generic HID compliant mouse from Creative model number OMC90S "CREATIVE MOUSE OPTICAL LITE". My other devices like external drives and controllers are unplugged when I'm not using them as having too many USB devices plugged in at a time causes a deadlock on almost all of the ports I have. Here's my system specifications (Most of these are from CPU-Z): Brand: Gateway DX4300-19 Mainboard: Gateway RS780 Chipset: AMD 780G Rev 00 Southbridge: AMD SB700 Rev 00 LPCIO: ITE IT8718 BIOS: American Megatrends Inc. ver P01-A4 09/15/2009 CPU: AMD Phenom II X4 810 at 2.60 GHz RAM: 8.0 GB DDR2 Dual Channel Ganged Mode at 400 MHz GPU: ATI Radeon HD3200 Graphics Intergrated - RS780 OS: Windows 7 Home Premium x64 OEM (Acer Group) HDD: WDC WD10EADS-22M2B0 1.0 TB (Western Digital Green Caviar) My BIOS has absolutely no control over how I setup the sleep mode to be either S1 or S3. So I can't check these settings or even change them. Hybrid sleep is also disabled, I can successfully go into hibernation and wake from hibernation but this is painfully slow due to a harddrive problem I'm having with this "Green Drive". (Hibernation takes over ~3 minutes to complete) Any help would be appreciated, thanks.

  Read the article

• Turning on Bluetooth disables wifi on Yoga 2

  - by Yostage

  I have a Lenovo Yoga 2. The moment that I turn on bluetooth, the wifi drops out - I lose connection, and connecting again shows "connection failed". If I turn the bluetooth off, wifi can reestablish fine. I've tried lots of different combinations of drivers for both the wifi and the bluetooth, but no combination has has changed this behavior yet. I've read some speculation that the cards have insufficient shielding, but that seems like kind of a large flaw to ship with. I've tried with a Carbon X1, a Yoga 2 Pro, and a Yoga 2 all next to each other on the desk while running InSSIDer. The X1 and the Y2P don't lose wifi connection when the bluetooth turns on, but the Y2 does immediately. The Y2P and the Y2 are running the same drivers for bluetooth and wifi, and appear to have the same wireless card internally. During the failure state, InSSIDer still sees signal strength for my network, but I cannot connect to it. stats: the card that comes in the laptop is an Intel Wireless-N 7260 Intel Bluetooth driver is at 17.0.1401.422 Intel Wireless driver is at 17.0.2.5 Windows 8.1 x64 Home wifi is a Medialink MWN-WAPR150N

  Read the article

• server 2008 r2 stuck on installing updates

  - by volody

  I have 2008 r2 64bit server that is stuck on installing updates. It shows message "Please do not power off or unplug your machine. Installing 57 of 61.." This message is shown for 3 hours now. I was trying to connect to this server using mmc. runas /user:AdministratorAccountName@ComputerName "mmc %windir%\system32\compmgmt.msc" RUNAS ERROR: Unable to run - mmc C:\Windows\system32\compmgmt.msc 1311: There are currently no logon servers available to service the logon request. What else can I do? Update: Remote Desktop does not work. It just disappear after entering username and password from Win7-64 computer Update: I have disconected server. Now Server Manager in Roles Summary shows message "Unexpected error refreshing Server Manager: The remote procedure call failed." Event log shows Could not discover the state of the system. An unexpected exception was found: System.Runtime.InteropServices.COMException (0x800706BE): The remote procedure call failed. (Exception from HRESULT: 0x800706BE) at System.Runtime.InteropServices.Marshal.ThrowExceptionForHRInternal(Int32 errorCode, IntPtr errorInfo) at Microsoft.Windows.ServerManager.ComponentInstaller.ThrowHResult(Int32 hr) at Microsoft.Windows.ServerManager.ComponentInstaller.CreateSessionAndPackage(IntPtr& session, IntPtr& package) at Microsoft.Windows.ServerManager.ComponentInstaller.InitializeUpdateInfo() at Microsoft.Windows.ServerManager.ComponentInstaller.Initialize() at Microsoft.Windows.ServerManager.Common.Provider.RefreshDiscovery() at Microsoft.Windows.ServerManager.LocalResult.PerformDiscovery() at Microsoft.Windows.ServerManager.ServerManagerModel.CreateLocalResult(RefreshType refreshType) at Microsoft.Windows.ServerManager.ServerManagerModel.InternalRefreshModelResult(Object state) Update: Manual update hangs on (Installing update 58 of 62...) Seurity Update for Windows Server 2008 R2 x64 Edition (KB979309) Update: It could be an issue with that admin user was renamed

  Read the article

• How to increase the speed between two external hard drives on my laptop?

  - by Roman

  Hello, I own Sony Vaio Z laptop with two external USB ports. It's quite new and has USB 2.0 support. I'm using Vista x64 on it. I also have two external usb hard drives, Iomega 500GB and WD for 1TB. Every hard drive has USB 2.0 support. I connect two devices to my laptop and trying to copy date from one hard drive to another. But it takes a lot of time! The speed is about 15 Megabytes per second. I have to wait toooooo long to copy all the information from one hard drive to another. When I try to copy information from my internal (SSD) hard drive, it works fine for both external drives. The speed is very high and it shows me something about 100 Megabytes per second. It makes me feel that USB 2.0 is OK on both drives. But when I'm trying to copy from one external drive to another external, I still get very low speed. I checked out Device Manager and here is the settings I have: (sorry, can't upload image because of my rating, check this url: http://picbite.com/image/122073daljo/ ) I think it's because two of my external drives use the same USB 2.0 controller. Is there any way to make it work faster? Is it possible to move one of my USB ports to other USB 2.0 controller? Or is there any software which can help me to automate copying all the files thru my internal drive? I have only about 3 gigabytes free space on internal drive and it's quite difficult to move manually every file from one hard drive to internal and then again to another internal.

  Read the article

• How to increase the speed between two external hard drives on my laptop?

  - by Roman

  Hello, I own Sony Vaio Z laptop with two external USB ports. It's quite new and has USB 2.0 support. I'm using Vista x64 on it. I also have two external usb hard drives, Iomega 500GB and WD for 1TB. Every hard drive has USB 2.0 support. I connect two devices to my laptop and trying to copy date from one hard drive to another. But it takes a lot of time! The speed is about 15 Megabytes per second. I have to wait toooooo long to copy all the information from one hard drive to another. When I try to copy information from my internal (SSD) hard drive, it works fine for both external drives. The speed is very high and it shows me something about 100 Megabytes per second. It makes me feel that USB 2.0 is OK on both drives. But when I'm trying to copy from one external drive to another external, I still get very low speed. I checked out Device Manager and here is the settings I have: (sorry, can't upload image because of my rating, check this url: http://picbite.com/image/122073daljo/ ) I think it's because two of my external drives use the same USB 2.0 controller. Is there any way to make it work faster? Is it possible to move one of my USB ports to other USB 2.0 controller? Or is there any software which can help me to automate copying all the files thru my internal drive? I have only about 3 gigabytes free space on internal drive and it's quite difficult to move manually every file from one hard drive to internal and then again to another internal.

  Read the article

• Problem Uninstalling Microsoft Internet Explorer

  - by Roger F. Gay

  On Windows Vista Home Premium (x64) I am trying to uninstall Microsoft Internet Explorer. The procedures explained all over the web involve going through the control panel to Programs and Features. If MSIE is listed there, then uninstall in the usual way. If it is not listed there, click Turn Windows features on and off and deactivate it there. But Internet Explorer is not listed in either place. Background: I initiated some process in MSIE a couple of months ago that caused all web pages to no longer save login information or remain logged in when requested. As you can tell from the way I described that, I don't remember what it was and have no way to simply reverse it. I had a few problems with .NET Framework as well. So, I've uninstalled all browsers except MSIE and uninstalled .NET Framework. I've reinstalled .NET Framework and all other browsers. I have not been able to uninstall MSIE. Have Tried: I tried installing over the existing installation, but auto-update must be keeping it nicely up to date. The attempt simply produced an information window telling me that my current version is more up-to-date than the new version I tried to install.

  Read the article

• Control Panel as menu includes a blank item

  - by Matthew Ferreira

  When viewed as a menu attached to the Start Menu in Windows 7 Ultimate x64, the Control Panel contains a blank item. It looks like this: This item cannot be deleted or removed. I also cannot create a shortcut to it. No error message is displayed, instead simply nothing happens. I've tried using Shell Object Editor (using Run as Administrator) to find out if there is an errant entry on the Control Panel, but many entries (almost two dozen) are blank. There are several valid entries as well. I've looked through the registry and through C:\Windows, \system32, and \SysWOW64 but have had no success. I looked at this question, but I am not using Windows XP and thus have no option to use Tweak UI's Rebuild Icons function. Please note that this is no empty entry in the Control Panel when opened normally, only when attached to the Start Menu as a menu. I have compared the list of entries on the attached menu to the normal Control Panel and other than the blank entry, they are exactly the same. Nothing is missing from one or the other. I've also compared the menu and the normal view to reference images and lists of Control Panel items and have found no irregularities. Is anyone familiar with this problem or know of a solution? I've performed virus and malware scans and found nothing. I've used CCleaner with no change. Nothing with Shell Object Editor. Nothing with Registry Editor. Certainly someone here knows how to fix this. My only guess is the many blank entries visible in Shell Object Editor, but I am reluctant to delete that many items without further analysis and guidance. I appreciate your time and consideration.

  Read the article

• How to take screenshots of WPF applications in correct size and content

  - by Thomas W.

  I usually take screenshots of single windows via the built-in key combination Alt+Print. Unfortunately this does not work well for more and more applications - all of them are WPF applications. Usually the screen shots have at least one of the following properties: the screenshot is larger than expected and contains parts of the screen around the actual window the screenshot has the correct size but includes parts of other windows, e.g. the Windows task bar. Of course the task bar might be in front of the window, but taking screen shots of "normal" programs works fine. How do I take screenshots of WPF application which are correct in size and content? I'd like to avoid the extra effort of checking all the screenshots for correctness, reproducing the situation, taking them again in case of issues or repairing/faking them manually in any pixel manipulation program (e.g. Paint.NET). I observe this on Windows 7 x64 SP 1, all official updates installed, but it might apply to other Windows versions as well (not tested yet). .NET 4.5 is installed. The application itself might only need the built-in .NET 3.5.1. It's reproducible on a virtual machine with the same settings. Examples: Screenshot of an application running in maximized mode. The screen shot includes parts of the task bar. Screenshot of a progress dialog which is behind the task bar. The screenshot also includes the task bar, while it doesn't for non WPF applications.

  Read the article

• 5.1 Surround Channels are Jumbled

  - by stickynips

  I had this exact setup working previously, but after a reformat it went screwy on me. I have an Onkyo A/V Receiver hooked up to my PC, via optical S/PDIF. Attached to the receiver is a 5.1 speaker setup (tested and working fine with my Xbox via the receiver). It seems to me that the audio channels are getting mixed up somehow between the PC and the receiver. I have a 5.1 test file which plays a sounds through each speaker individually. The channels are mixed as such: "Left Front" plays through my Right Front speaker "Center" plays through my Left Front speaker "Right Front" plays through my Center speaker "Left Rear" plays through my Subwoofer "Right Rear" plays through my Left Rear speaker I've tried downloading the latest Realtek HD Audio Drivers and the Realtek HD Audio Manager, but neither makes any difference. If there's a way I can manually rearrange the channels I believe it would fix the problem, but as far as I know this is impossible. edit: Sorry, I've forgotten some basic info. I'm running Windows 7 x64. The sound card is Realtek ALC892 embedded in a GIGABYTE GA-890GPA-UD3H AM3 motherboard.

  Read the article

• How do I set Internet Explorer 64-bit as my default browser?

  - by Brian Knoblauch

  Windows Vista x64. It defaults to IE 32-bit, and will not allow me to set 64-bit as the default with the "Make Default" button. I'm currently forced to workaround by starting IE 64-bit manually, and leaving it up with an empty window. Then when links are fired from apps, they open in that 64-bit version. Problem being is that sometimes I forget and get a bunch of stuff opened in 32-bit without realizing it. Then I have to remember all the links I clicked, close ALL of them, open IE 64-bit, and put them all back in. Trying to avoid all that re-work when I forget to do the workaround. Unfortunately, all the forums I've googled that discuss this just have a bunch of people saying "don't do that" and "you don't want to do that". Yes, I do want to do this. The particular feature I use only works right in my 64-bit version, and I don't use 32-bit plugins. I fully understand the implications of what I'm doing. :-)

  Read the article

• Windows Media Center showing Jerky Video on PC

  - by Kris Erickson

  I had to repave my Windows 7 x64 box last week due to a hard drive crash, and for a while everything was running perfectly but now all videos in Windows Media Center are jerky (the sound is fine, they just seem to skip a ton of frames all the time). This is on the local machine, but the same thing happens when I try to stream to my Xbox. The videos all show fine in VLC and Windows Media Player (however exhibit the same problem in Quicktime). I guess I must have installed something recently (in the process of getting all the apps I usually have running on my PC) that caused this but for the life of me I can't figure it out. I have updated to the latest video driver (and then rolled back to the standard Windows 7 driver), I have rolled back all the other drivers that I have installed (I believe). I have uninstalled all the codec packs (I also run TVersity, so I have the TVersity codec pack installed), and I uninstalled TVersity. Nothing seems to help. I have uninstalled windows media center, and reinstalled it from the Programs and Features. I have basically ran out of things to try to fix this, and am almost thinking about reinstalling Windows again. Any suggestions? Edit Specs on the PC (which I figured was unimportant since everything used to work perfectly): Intel Core 2 CPU 6600 @ 2.4 Ghz Nvidia GTS 8800 Built in realtek-audio soundcard 4GB Ram Codecs which are failing: All that I have tried, but at least Xvid, Mpgv (mpeg2 video from a camera), and Wmv (only kinds that I have ready access to).

  Read the article

• What to do when a device has no driver for Windows 7 but it has Vista, XP drivers

  - by Mehper C. Palavuzlar

  This has always been a bothersome matter for me. Some devices (printers, scanners, etc.) have drivers for older versions of Windows (Vista, XP, 2000, NT) but no driver for Windows 7. What are my chances to install such devices on Windows 7? Example case: I have a Sharp printer & scanner (Sharp AR-122E N) which I have used for my old Windows XP based PC. Now I want to install it on a Windows 7 x64 based PC. Windows 7 cannot load its driver. I used the original driver CD but when I run the setup.exe (which is included in AR122EN111.exe, 6713KB), it says Cannot install driver on this operating system. Supported operating systems are: Windows 2000, XP, Vista. I tried to install the driver using compatibility settings. I tried Windows Vista and Windows XP SP3, but to no avail. The setup gave the same error. I also googled for Windows 7 driver for "Sharp AR-122E N" but it only listed the original driver that I tried. The official site of Sharp does not even list the driver for this product. In the past, the compatibility setting workaround did work for some devices, but this time it failed. What else can I do to overcome this problem?

  Read the article

• VNC Address Book - Window Invisible? Working as intended?

  - by user1445967

  I have VNC Server and VNC Viewer on the same PC with Windows 7 Ultimate x64. Is VNC Address Book supposed to have a main application window? I can't tell if this is bugged or working as intended. When I start VNC Address book, it creates an item in the task list and also an icon in the notification area. If I click the task list item once, nothing happens. If I click again, it disappears from the task list but remains in the notification area**. If I right-click the icon on the notification area, there is an option 'open address book', which if chosen, creates the item in the task list again, with the exact same behavior. If I left or right click on the address book icon, I have ways to connect to servers in the address book. However I have no way to add/remove/edit servers in the address book. **Note that this behavior is identical to that of an application with a main window where there is an option to 'minimize to system tray / notification area'. Only here, no main window is visible, ever. If fixing this problem is beyond the scope of this site, that's fine, but at this point I have no real way to tell if the program is malfunctioning on my pc or if it is far more minimalist than I expected. There appears to be no forum on realvnc.com where I can ask about this, perhaps this is to prevent me from getting any help unless I pay to register?

  Read the article

• best practices for setting up a new windows 2008 R2 server with ec2 AWS

  - by Alex

  Can someone comment what they would add to the following list of SOP in terms of best practices? This is being set up on AWS, and then after further testing, back in our datacenter. Standard Operation Procedure (SOP): Installation Part: 2 - Installation of Software Components in Windows 2008 R2 (Updated). Step: 1 Logon to the host through Remote Desktop. Strp: 2 Open Server Manager - Server Roles - Install Web Server IIS 7.5 with compatible of IIS 6 features and Management compatibility mode. Step: 3 Open IE/Mozilla to Download the below listed software's and save all installation files to folder called "AWS Server Install Files" for future reference.. Net Framework 2.0 (Download that from internet) Crystal reports for .Net Framework 2.0 (x64) (Download that from internet) SQL Server 2005 (AWS Image) Step: 4 Once all software's saved on local drive, then Install it one by one. Step: 5 Navigate to Desktop folder to install the below listed softwares. Microsoft Asp.net 2.0 AjaxExtention 1.0 (placed on Desktop \Softwares) WebEx recorder. (placed on Desktop \Softwares) Winrar(placed on Desktop \Softwares) Step: 6 Make sure all the software are working fine. Step: 7 Inspect the server once entirely. Step: 8 Logoff & Stop the Instance.

  Read the article

• Fresh 12.04 Install - mySQL not starting

  - by Lee Armstrong

  I have a freshly installed Ubuntu 12.04 x64 server and I installed Percona server from their official repositories. Trouble is it will not start! mysql-error.log shows nothing obvious. 121129 12:16:54 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql/ 121129 12:16:54 [Note] Plugin 'FEDERATED' is disabled. 121129 12:16:54 InnoDB: The InnoDB memory heap is disabled 121129 12:16:54 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121129 12:16:54 InnoDB: Compressed tables use zlib 1.2.3 121129 12:16:54 InnoDB: Using Linux native AIO 121129 12:16:54 InnoDB: Initializing buffer pool, size = 12.0G 121129 12:16:54 InnoDB: Completed initialization of buffer pool 121129 12:16:54 InnoDB: highest supported file format is Barracuda. 121129 12:16:55 InnoDB: Waiting for the background threads to start 121129 12:16:56 Percona XtraDB (http://www.percona.com) 1.1.8-rel29.1 started; log sequence number 1598476 121129 12:16:56 [Note] Server hostname (bind-address): '0.0.0.0'; port: 3306 121129 12:16:56 [Note] - '0.0.0.0' resolves to '0.0.0.0'; 121129 12:16:56 [Note] Server socket created on IP: '0.0.0.0'. 121129 12:16:56 [Note] Event Scheduler: Loaded 0 events 121129 12:16:56 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.5.28-29.1-log' socket: '/var/run/mysqld/mysql.sock' port: 3306 Percona Server (GPL), Release 29.1 121129 12:16:56 [Note] Event Scheduler: scheduler thread started with id 1 And the syslog shows... Nov 29 12:17:07 V-PF-SQL1 /etc/init.d/mysql[2206]: 0 processes alive and '/usr/bin/mysqladmin --defaults-file=/etc/mysql/debian.cnf ping' resulted in Nov 29 12:17:07 V-PF-SQL1 /etc/init.d/mysql[2206]: #007/usr/bin/mysqladmin: connect to server at 'localhost' failed Nov 29 12:17:07 V-PF-SQL1 /etc/init.d/mysql[2206]: error: 'Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2)' Nov 29 12:17:07 V-PF-SQL1 /etc/init.d/mysql[2206]: Check that mysqld is running and that the socket: '/var/run/mysqld/mysqld.sock' exists! Nov 29 12:17:07 V-PF-SQL1 /etc/init.d/mysql[2206]: The socket file is being created and I can access the server NOT using the socket using mysql -h 127.0.0.1 -P 3306 -u root --pPASSWORD

  Read the article

• Windows 7 remote desktop encryption error every few minutes

  - by rfrankel

  Because of an error in data encryption, this session will now end. This is the error I've been getting more and more frequently over the past few days, to the point that I can't ignore it because it's happening consistently within 5 minutes of connecting - sometimes within a few seconds. Both the remote and local machines are Windows 7 Pro x64. The remote machine is behind a Linksys RV082, and I'm using UPnP to forward a remote port to the correct local port. This setup had been working fine for several months, and I can't think of any recent relevant changes that might have been made. Things I've already tried: Disabling unnecessary components of the network connection on the remote machine, until only IPv4 and Client for Microsoft Networks remain. Disabling TCP large send offload on both the remote and local machines. Confirming that the remote machine is not mentioned anywhere in any DMZ settings on the Linksys router. Confirming that there are no x509-related registry keys screwing things up (this is the suggested fix for a slightly different error anyway). These are the only solutions I've been able to find after about an hour of searching, and most of them apply to XP or Server 2003 in any case. If anyone could suggest something else, it would be much appreciated.

  Read the article

• Windows 8 Fails to install with corrupted graphics

  - by Andy

  I am trying to install Windows 8 Pro Upgrade via the download method on an older PC (07-08). It is a Dell Dimension E521 but it has been upgraded with a 3.0 Ghz Dual Core AMD Processor, 120 GB SSD, and 4 GB of RAM. The Windows 8 upgrade assistant did not detect any issues or concerns with upgrading other than I don't have DVD software installed. The system install Windows 8 but on the first boot, corrupt graphics are present. Eventually, the monitor will go into sleep mode and then roll back to Windows 7 Pro X64 which runs fine. I wouldn't be upset over not being able to install Windows 8, but I already paid for the software since I thought there would be no issues upgrading. The Graphics card in the system is the Geforce 7300LE and it has the latest NVidia drivers for Windows 7 loaded. I saw this solution which is similar to my problem: Corrupt graphics during Windows 8 installation However, I have downloaded Windows 8 and I am not sure how to go about modifying the install that resides somewhere on the hard drive. Thanks in advance for any assistance.

  Read the article

• netlogon errors

  - by rorr

  I have two instances of mssql 2005 and am using CA XOSoft replication. The master is a failover cluster and the replica is a standalone server. They are all running Server 2003 sp2 x64. Same patch levels on all servers. This setup has worked great for several months until we recently restricted the RPC ports on both nodes of the master(5000 - 6000 using rpccfg.exe). We have to implement egress filtering, thus the limiting of the ports. We began receiving login errors for sql windows authentication and NETLOGON Event ID: 5719: This computer was not able to set up a secure session with a domain controller in domain due to the following: Not enough storage is available to process this command. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. We also see group policies failing to update and cluster file shares go offline at the same time. The RPC ports were set back to default when we started seeing these problems and the servers rebooted, but the problems persist. The domain controllers are not showing any errors. Running dcdiag and netdiag shows everything is fine. We have noticed that the XOSoft service ws_rep.exe is using a lot of handles(8 - 9k), about the same number that sqlserver is using. As soon as xosoft replication is stopped the login errors cease and everything functions correctly. I have opened a ticket with CA for XOSoft, but I'm not sure that the problem is actually xosoft, but that it is the one bringing the problem to light. I'm looking for tips on debugging RPC problems. Specifically on limiting the ports and then reverting the changes.

  Read the article

• Queries passed to SQL Server are getting corrupted

  - by adrianbanks

  We are experiencing a bizarre error with our application at a customer site. We have managed to narrow it down to the point where we can replicate the behaviour using just Management Studio and SQL Server. We have two machines, A and B: +------------+ +--------------------+ | [A] | | [B] | | Management | -------------- | SQL Server 2008 R2 | | Studio | | Enterprise x64 | +------------+ +--------------------+ We are running a SQL script in Management Studio on machine A against the SQL Server instance on machine B. We are not actually executing the script, just parsing it. Most of the time, the parse operation works fine. Occasionally (seemingly randomly), the parse operation fails with a syntax error. The error message shows the part of the script with the error, which appears as some SQL from the original script that has been truncated and has random characters appended to it. An example: The original SQL: SELECT DISTINCT ST.TABLE_NAME as TableName FROM INFORMATION_SCHEMA.TABLES AS ST INNER JOIN INFORMATION_SCHEMA.COLUMNS AS SC ON SC.TABLE_NAME = ST.TABLE_NAME WHERE ST.TABLE_TYPE = 'BASE TABLE' AND SC.COLUMN_NAME = 'Identity' AND ST.TABLE_NAME != 'dtproperties' ORDER BY ST.TABLE_NAME The SQL that is in error (as reported by SQL Server): SELECT DISTINCT ST.TABLE_NAME as TableName FROM INFORMATION_SCHEMA.TABLES AS ST INNER JOIN INFORMATION_SCHEMA.COLUMNS AS SC ON SC.TABLE_NAME = Sa? The above example shows how the query is being corrupted. It doesn't always happen, and is not always the same bit of SQL that causes the error. Parsing this script against another SQL Server instance produces no errors, showing that the script is fine. It appears that something is corrupting the SQL that is being received the the server. This leads me to think that the problem lies either with the client end or in the transmission of the SQL from the client to the server. I have a SQL trace from the period where an error occurs, which shows the SQL has been corrupted when SQL Server receives it. We have been unable to track down any possible cause of this behaviour, and so cannot find a fix. Because the errors occur seemingly randomly, it is also very hard to generate reproduction steps to submit a bug report. Any ideas?

  Read the article

• Winamp has slow /skipping video playback on Windows 7

  - by Roy Rico

  Hello, I have Windows 7 x64 (7600 90-day trial version) and Winamp 5.6 installed. When I play a video in Windows Media Player, the video plays smooth, however when I play a video in winamp, the video is mostly ok when played back at the original size (but not completely), but if I play it back in fullscreen, the playback gets really slow. The video's audio track plays just fine. I have a DELL XPS 420 computer (8GB of RAM) with a Nvidia GeForce 8800 CTS 512 video card. I've updated to the latest drivers. I have the default Windows 7 codecs, and the CCCP codec pack which used to be all I needed under Windows XP to play all types of videos. Are the codecs needed for Windows Y the same? What's going on? UPDATE: As suggested, I turned off Aero and winamp ran just fine again. So I just have to wait for winamp to be rewritten to work with the way Vista/Windows 7 runs? UPDATE 2: Winamp has updated their player, and it works great with Windows 7 now.

  Read the article

• Lenovo System Update Breaks Windows Live

  - by wolfvilleian

  Hey everyone, I've been racking my brain (and fingers from typing) trying to solve this issue to no avail. I have a Lenovo computer and I install their system update tool to install all my missing drivers. However after this tool is installed Windows Live 2011 breaks, it will no longer sign in giving error number 8e5e0247 all the solutions online haven't helped. It appears that a language setting somewhere gets set to en_ms, and I'm en_ca. My computer is running Windows 7 x64. When i try to sign onto messenger it gives an error that (with some research) means your locale or language is not supported, I've searched my computer for any reference to en_ms but find none. Also a few other things seem to have broken, When a UAC box comes up it is no longer able to identify the publisher of anything, and also the indexing service does not work (I'm not sure if the indexing issue is related, but the UAC issue happened right after installation), I had this issue before but I don't remember how I fixed it, I believe it had something to do with environmental variables. When it goes to sign in it gets as far as the "Loading contacts" then stops and goes back to the sign in screen. Has anyone seen this before? Thanks

  Read the article

< Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >