Search Results

Search found 20168 results on 807 pages for 'service'.

Page 757/807 | < Previous Page | 753 754 755 756 757 758 759 760 761 762 763 764  | Next Page >

• Brand new Mac Pro tower fan suddenly runs full-tilt

  - by Caffeine Coma

  My Quad-Core Mac Pro tower is two days old. Initially, I was impressed with how quiet it was compared to my older Macbook Pro. Then on day two, for some reason it started running very loudly. It's not just a "little" loud- my wife walked into the room and asked what the noise was. At first I thought this was just because I was hitting the CPU a bit (importing my iPhone library into iLife '09, and running Eclipse). But now that that's done, Activity Monitor shows a virtually idle CPU; there's nothing running that ought to be causing this, as far as I can tell. I tried powering it off & letting it cool down for a few minutes to no avail; about 10 seconds after powering up, the box gets loud again. I took a look at it with the side cover off, and it seems to be the fan near the top middle, between the power supply and the disk drive. It can't be a dust issue, as the machine is only 2 days old (and I peeked inside anyway just to be sure- clean). I did do a software update over the past 24 hours or so, but I can't say that it occurred immediately after that. I also did a migration of my old apps and data from my MBPro, for what it's worth. Why is it suddenly so loud? How can I monitor the fan speed and various system temperatures? Here's a link to my temps and fan speeds. UPDATE 1: Took it to the Apple Store. They took it in the back (where it's presumably quieter) and ran a fan diagnostic; no problems were found. The guy also told me that it was "a little loud", but normal. I don't buy it. It was virtually silent the first 24 hours I was using it. They would not replace/service it in the store (grrr... that's why I went there, as directed by Apple Care) but said I could get a replacement from the online store, as it was just purchased. I think I will try that. UPDATE 2: Apple is letting me send it back for a replacement. Glad to see so many responses to this question mentioning that the MacPros are usually silent; it's not all just in my head. :-)

  Read the article

• Force Finder to log in as Guest to a SMB share

  - by slhck

  I have a QNAP NAS that offers a few SMB shares. As I'm in a trusted environment, my shares are accessible as guest rather than with a combination of username and password. Problem Now, when I click the name of the device in Finder's sidebar, I get the black "Connection failed" bar, with the option "Connect as...". When I click that, I receive: I can however press ? + K and enter the server's name manually, which gets me to this window: Here, I have to select "guest". Now, I can select one of the shares to connect to, and I'm finally connected to the server. If I select it in the sidebar, I get a list of all shares available, because I'm connected as "guest", obviously: What I need Well, as soon as I unmount all shares, I have to go through the same procedure of manually logging in as "guest" again, which I find quite annoying. Is there any way I could get Finder (or the underlying SMB client) to know which credentials to use? Or should I look for the solution rather on the server side? (I know that other SMB shares seem to work fine in my network) Diagnostics The only thing I can get out of Console.app is: 5/15/11 7:36:40 PM /System/Library/CoreServices/Finder.app/Contents/MacOS/Finder[200] SharePointBrowser::handleOpenCallBack returned 64 This message occurs when I click the name of the SMB server in the Finder sidebar. Here's the output of `smbclient -L meredith -U guest -d=2 charon:~ werner$ smbclient -L meredith -U guest -d=2 added interface ip=192.168.100.11 bcast=192.168.100.255 nmask=255.255.255.0 tdb(unnamed): tdb_open_ex: could not open file /private/var/samba/gencache.tdb: Permission denied Got a positive name query response from 192.168.100.100 ( 192.168.100.100 ) Password: Domain=[MEREDITH] OS=[Unix] Server=[Samba 3.5.2] Sharename Type Comment --------- ---- ------- music Disk movies Disk photos Disk software Disk archive Disk backups Disk IPC$ IPC IPC Service (NAS Server) Got a positive name query response from 192.168.100.100 ( 192.168.100.100 ) Domain=[MEREDITH] OS=[Unix] Server=[Samba 3.5.2] Server Comment --------- ------- Workgroup Master --------- ------- WORKGROUP MEREDITH Also, things I've tried: There is no relevant entry in the Keychain (but why would it, I'm only connecting as guest) Connecting with user name "Guest" and empty password logs me in but still after ejecting the last share, I get the same "Connection failed" error as before. The appropriate entry is made in the Keychain but obviously has no effect.

  Read the article

• Force Finder to log in as Guest to a SMB share

  - by slhck

  I have a QNAP NAS that offers a few SMB shares. As I'm in a trusted environment, my shares are accessible as guest rather than with a combination of username and password. Problem Now, when I click the name of the device in Finder's sidebar, I get the black "Connection failed" bar, with the option "Connect as...". When I click that, I receive: I can however press ? + K and enter the server's name manually, which gets me to this window: Here, I have to select "guest". Now, I can select one of the shares to connect to, and I'm finally connected to the server. If I select it in the sidebar, I get a list of all shares available, because I'm connected as "guest", obviously: What I need Well, as soon as I unmount all shares, I have to go through the same procedure of manually logging in as "guest" again, which I find quite annoying. Is there any way I could get Finder (or the underlying SMB client) to know which credentials to use? Or should I look for the solution rather on the server side? (I know that other SMB shares seem to work fine in my network) Diagnostics The only thing I can get out of Console.app is: 5/15/11 7:36:40 PM /System/Library/CoreServices/Finder.app/Contents/MacOS/Finder[200] SharePointBrowser::handleOpenCallBack returned 64 This message occurs when I click the name of the SMB server in the Finder sidebar. Here's the output of `smbclient -L meredith -U guest -d=2 charon:~ werner$ smbclient -L meredith -U guest -d=2 added interface ip=192.168.100.11 bcast=192.168.100.255 nmask=255.255.255.0 tdb(unnamed): tdb_open_ex: could not open file /private/var/samba/gencache.tdb: Permission denied Got a positive name query response from 192.168.100.100 ( 192.168.100.100 ) Password: Domain=[MEREDITH] OS=[Unix] Server=[Samba 3.5.2] Sharename Type Comment --------- ---- ------- music Disk movies Disk photos Disk software Disk archive Disk backups Disk IPC$ IPC IPC Service (NAS Server) Got a positive name query response from 192.168.100.100 ( 192.168.100.100 ) Domain=[MEREDITH] OS=[Unix] Server=[Samba 3.5.2] Server Comment --------- ------- Workgroup Master --------- ------- WORKGROUP MEREDITH Also, things I've tried: There is no relevant entry in the Keychain (but why would it, I'm only connecting as guest) Connecting with user name "Guest" and empty password logs me in but still after ejecting the last share, I get the same "Connection failed" error as before. The appropriate entry is made in the Keychain but obviously has no effect.

  Read the article

• Microsoft signed drivers appears as publisher not verfied

  - by Priyanka Gupta

  Task at hand: Microsoft sign drivers on Win 7. I microsoft signed my driver package 3 times every time thinking I might have missed a step or something. However, I cannot seem to get rid of the Windows Security error message "Windows can't verify the publisher of this driver software'. This is not the first time I have signed the driver packages. I was successfully able to sign other driver packages a few months ago. However, with this driver package I keep getting Windows security dialog box. Here's the procedure I follow - Create a new cat file using INF2CAT tool. Self sign the driver using a Versign Class 3 Public Primary Certification Authority - G5.cer. Run the microsoft tests on DTM Servers and clients with the devices that use this driver. Create WLK submission package. Self sign the cab file. Submit the package for certification. The catalog file that comes back after successfully passing tests says Name of signer "Microsoft Windows Hardware Comptibility Publisher". When I check the validity of signature using SignTool, it says the signature is vaild. However, when I try to install the driver with new signed catalog file the windows complain. Any ideas? Edit 11/12/2012: Reply to Eugene's comment Thanks for the help, Eugene. Yes. I did sign two other driver packages before. One of them was modified version of WinUSB driver. I am using the same certificate I used when I signed those two driver packages a few months ago. It costs $250 per signing from Microsoft. I would think that Microsoft would complain about it during certification if the certificate is wrong. I use the following command to self sign the CAT file. I don't have to specify the ceritificate name as there's only one certificate in the directory - Signtool sign /v /a /n CompanyName /t http://timestamp.verisign.com/scripts/timestamp.dll OurCatalogFile.cat Below is the result from running Verify command on the Microsoft signed OutCatalogFile.cat C:\Program Files\Microsoft SDKs\Windows\v7.1\Bin\x64signtool verify /v "C:\User s\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Verifying: C:\Users\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Hash of file (sha1): BDDF39B1DD95881B462164129758A7FFD54F47D9 Signing Certificate Chain: Issued to: Microsoft Root Certificate Authority Issued by: Microsoft Root Certificate Authority Expires: Sun May 09 18:28:13 2021 SHA1 hash: CDD4EEAE6000AC7F40C3802C171E30148030C072 Issued to: Microsoft Windows Hardware Compatibility PCA Issued by: Microsoft Root Certificate Authority Expires: Thu Jun 04 16:15:46 2020 SHA1 hash: 8D42419D8B21E5CF9C3204D0060B19312B96EB78 Issued to: Microsoft Windows Hardware Compatibility Publisher Issued by: Microsoft Windows Hardware Compatibility PCA Expires: Wed Sep 18 18:20:55 2013 SHA1 hash: D94345C032D23404231DD3902F22AB1C2100341E The signature is timestamped: Tue Nov 06 11:26:48 2012 Timestamp Verified by: Issued to: Microsoft Root Authority Issued by: Microsoft Root Authority Expires: Thu Dec 31 02:00:00 2020 SHA1 hash: A43489159A520F0D93D032CCAF37E7FE20A8B419 Issued to: Microsoft Timestamping PCA Issued by: Microsoft Root Authority Expires: Sun Sep 15 02:00:00 2019 SHA1 hash: 3EA99A60058275E0ED83B892A909449F8C33B245 Issued to: Microsoft Time-Stamp Service Issued by: Microsoft Timestamping PCA Expires: Tue Apr 09 16:53:56 2013 SHA1 hash: 1895C2C907E0D7E5C0292B92C6EA8D0E236F525E Successfully verified: C:\Users\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Number of files successfully Verified: 1 Number of warnings: 0 Number of errors: 0 Thank you!

  Read the article

• Email server can send internal, but messages never arrive at external recipients

  - by Chase Florell

  I'm running MailEnable on my server, and have been for many years. Recently we had an attack on our server, and I was able to close the hole. Since then, our mail server doesn't seem to be sending mail out. If I send an email from myself to another account hosted on the server, the email arrives as expected. If I send an email from my gmail account to my business account, the email also arrives as expected The problem comes when I send from my business account to an external domain I tried the following Gmail.com Hotmail.com Shaw.ca When I send to any of the above The message leaves my client as expected, The logs appear to accept and forward on the message The SMTP outbound que is empty The message never arrives I have checked our domain with mxtoolbox.com senderbase.org And neither of them are reporting any problems with our domain. I have ensured that port 25 is open (along with the other standard ports) Here is one of the log entries from the SMTP connector 11/05/13 12:10:00 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 220 mx1.example.com ESMTP MailEnable Service, Version: 6.81--6.81 ready at 11/05/13 12:10:00 0 0 11/05/13 12:10:00 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 EHLO EHLO ASSP.nospam 250-mx1.example.com [127.0.0.1], this server offers 6 extensions 159 18 11/05/13 12:10:00 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 EHLO EHLO ASSP.nospam 250-mx1.example.com [127.0.0.1], this server offers 6 extensions 159 18 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 AUTH AUTH LOGIN 334 VXNlcm5hbWU6 18 12 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 AUTH {blank} 334 UGFzc3dvcmQ6 18 26 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 AUTH Y29sb25lbGZhY2U= 235 Authenticated 19 18 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 MAIL MAIL FROM:<[email protected]> 250 Requested mail action okay, completed 43 31 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 RCPT RCPT TO:<[email protected]> 250 Requested mail action okay, completed 43 35 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 DATA DATA 354 Start mail input; end with <CRLF>.<CRLF> 46 6 [email protected] Here are the headers of the sent message X-Assp-Version: 1.7.5.7(1.0.07) on ASSP.nospam X-Assp-ID: ASSP.nospam 78601-04523 X-Assp-Intended-For: [email protected] X-Assp-Envelope-From: [email protected] Received: from [10.10.1.101] ([68.147.245.149] helo=[10.10.1.101]) with IPv4:587 by ASSP.nospam; 5 Nov 2013 12:10:00 -0700 From: Chase Florell <[email protected]> Content-Type: text/plain Content-Transfer-Encoding: 7bit Subject: Test Message Message-Id: <[email protected]> Date: Tue, 5 Nov 2013 12:10:18 -0700 To: Chase Florell <[email protected]> Mime-Version: 1.0 (Mac OS X Mail 7.0 \(1816\)) X-Mailer: Apple Mail (2.1816) . Where else can I check to see if there is something broken? What could cause a problem like this whereby the message appears to send, but never arrives, and never returns a bounce?

  Read the article

• CPU Lockup when loading folder of bookmarks in Firefox

  - by Gary M. Mugford

  I am running Firefox 3.6 on WinXPSP3 on a duo Core machine with 4G of memory. I am also running Avast! free anti-virus and ZoneAlarm free firewall, both latest versions. Within the last month, my service provider basically forced me to upgrade to a Docsis 3.0 compliant modem (offered me a deal I couldn't turn down). At that point, I also upgraded to FF3.6. Basically, I am not unhappy with many aspects of this switchover, EXCEPT, when I now load a folder of bookmarks (anywhere from 10 to 38) I get nothing like the load times I experienced a couple of months back. It's taking minutes rather than seconds. And the first bookmark in one of the folders, GMail, rarely loads before timing out. I have used the old trick of powering off the cable modem before my day's work. This used to fix 'load-lag' in the old days. I have switched from my ISP's DNS server to Google, OpenDNS and back. And nothing seems to work currently. It's not my DNS cache. That's been flushed and secondary computers also have the same issue when loading folders. I have watched the CPU usage and loading the folder will send VSMon (ZoneAlarm) usage over 40 percent, AVastSvc (Avast!) over 30 and Firefox will then push the needle to 100. There's a brief burst by SVCHost when the others falter in devouring cycles. Then everything subsides to single digits once the last tab is loaded. The only other nominal nastiness is VSMon ALWAYS hitting 50 percent when ANY program starts downloading content from the internet. If I shutdown ZoneAlarm (and VSMon with it), the same slow loading takes place, but this time System is running 50% plus, again driving the usage to 100 per cent. I have my doubts FF3.6 vs FF3.5 is an issue, since the other computers are still running 3.5 and suffer the same issue. Those computers are on, but inactive, most of the time, being backups. Obviously, when the CPU hits 100, I can't do much of anything in FireFox OR in other programs. Video play through WMPC or VLC is extremely choppy, although it doesn't seem to affect the audio. Any ideas what I can try next? Thanks, GM

  Read the article

• Installing OpenLDAP: ldap_bind: Invalid credentials (49)

  - by Arcturus

  Hello. I've been trying to set up the OpenLDAP installed by default on Fedora 12, very unsuccessfully. My ultimate goal is to use LDAP authentication for user login and Apache, using the OpenLDAP server running on the same machine. The server is running, but the error I always get when I try to use ldapsearch or ldapadd is: ldap_bind: Invalid credentials (49) I've been following these tutorials, but none of them helped me: http://www.howtoforge.com/openldap_fedora7 http://www.redhat.com/docs/manuals/linux/RHL-9-Manual/ref-guide/s1-ldap-quickstart.html http://www.howtoforge.com/linux_ldap_authentication http://docs.fedoraproject.org/deployment-guide/f12/en-US/html/s1-ldap-pam.html http://www.openldap.org/doc/admin24/quickstart.html First, some components were already installed, and I installed these with yum: yum install openldap-servers openldap-devel Then, I created a basic slapd.conf file in /etc/openldap: database bdb suffix "dc=sniejana-sandbox,dc=com" rootdn "cn=root,dc=sniejana-sandbox,dc=com" rootpw {SSHA}cxdz55ygPu4T3ykg7dgu+L0VRvsFSeom directory /var/lib/ldap/sniejana-sandbox.com I obtained the rootpw with this command: slappasswd -s changeme I also created the /var/lib/ldap/sniejana-sandbox.com directory and made sure the entire contents of /var/lib/ldap were owned by the ldap user. I found two ldap.conf files, one in /etc and one in /etc/openldap. I don't know which is the right one. If I understood correctly, this file is to configure the client. I put this in both: HOST localhost BASE dc=sniejana-sandbox,dc=com I then ran the server with: service slapd start It said OK. Most of the tutorials above say to use the command ldapsearch -D "cn=Manager,dc=my-domain,dc=com" -W to ensure that everything's working. When I execute this command, a password prompt appears, and after entering the password, I get the error. ldapsearch -D "cn=root,dc=sniejana-sandbox,dc=com" -W Enter LDAP password: ldap_bind: Invalid credentials (49) The same thing happens when trying to use ldapadd. I tried with an encrypted and unencrypted password in slapd.conf, it doesn't change anything. Adding a -x for simple authentication doesn't change anything either. netstat -ap confirms the server is listening: tcp 0 0 *:ldap *:* LISTEN 4148/slapd tcp 0 0 *:ldap *:* LISTEN 4148/slapd ps -ef|grep slapd confirms the process is running: ldap 4148 1 0 15:22 ? 00:00:00 /usr/sbin/slapd -h ldap:/// -u ldap Running slaptest procudes config file testing succeeded. I read somewhere that the command ldapsearch -x -b '' -s base '(objectclass=*)' namingContext can confirm the server is running. It appears to work: # extended LDIF # # LDAPv3 # base <> with scope baseObject # filter: (objectclass=*) # requesting: namingContext # # dn: # search result search: 2 result: 0 Success # numResponses: 2 # numEntries: 1 I'm running out of ideas. Am I missing something obvious?

  Read the article

• Where to get laptop replacement parts?

  - by wai

  I am sure some of us have older laptops that still works but just one or two parts started not working very well. However, to send it back to the manufacturer for repair might not be worth the money (as some of them even charge consultation fees just to have it checked) as these old laptops are most probably well beyond warranty. Replacing these one or two parts could give your laptop a new lease of life. For example, I have a Dell Inspiron 640m which the fan recently failed. Everything else still works. I know enough to open up the laptop (after reading the service manual) and put it back together again, hence a replacement fan could save it. However, finding these parts turned out to be difficult. I guess I wouldn't be able to get it from Dell since I have been searching around the Dell forums and concluded if I were going to get Dell to at least talk to me, I would have to pay some money (since my warranty expired). I found this online:- http://www.parts-people.com/index.php?action=item&id=3725 However, as I don't live in the United States, shipping alone would cost me 3 times more than the part in question. In addition, if there's a problem, it would be difficult because I probably would have to mail the parts back (costing more money). One of my friend spilled water on her Macbook, she sent it back to Apple and they told her the cost of repairing it exceeds that of buying a new Macbook. They probably have to change everything except the LCD screen. I opened it up and found that most of the parts are still working, only the RAM had fried. Replaced it and it's working again. For some time before discovering only the RAM fried, I was toying with the idea of replacing the logic board myself but looks like I didn't have to. =) Now I know there's a site for Macbooks used replacement parts:- http://www.ifixit.com/ The question is, does anyone know where to get replacement parts at their own locality? It might benefit the community as a whole. Someone might know a local computer store that sells precisely just the things we needed (for now, I hope to find a shop that sells just the fan). If you own a laptop which you had an easy experience finding the replacement parts, do post that as well. PS: I wish laptop manufacturers have outlets where they sell these replacement parts (or at least let you place an order).

  Read the article

• Why won't vyatta allow SMTP through my firewall?

  - by Solignis

  I am setting up a vyatta router on VMware ESXi, But I see to have hit a major snag, I could not get my firewall and NAT to work correctly. I am not sure what was wrong with NAT but it "seems" to be working now. But the firewall is not allowing traffic from my WAN interface (eth0) to my LAN (eth1). I can confirm its the firewall because I disabled all firewall rules and everything worked with just NAT. If put the firewalls (WAN and LAN) back in place nothing can get through to port 25. I am not really sure what the issue could be I am using pretty basic firewall rules, I wrote the rules while looking at the vyatta docs so unless there is something odd with the documentation they "should" be working. Here is my NAT rules so far; vyatta@gateway# show service nat rule 20 { description "Zimbra SNAT #1" outbound-interface eth0 outside-address { address 74.XXX.XXX.XXX } source { address 10.0.0.17 } type source } rule 21 { description "Zimbra SMTP #1" destination { address 74.XXX.XXX.XXX port 25 } inbound-interface eth0 inside-address { address 10.0.0.17 } protocol tcp type destination } rule 100 { description "Default LAN -> WAN" outbound-interface eth0 outside-address { address 74.XXX.XXX.XXX } source { address 10.0.0.0/24 } type source } Then here is my firewall rules, this is where I believe the problem is. vyatta@gateway# show firewall all-ping enable broadcast-ping disable conntrack-expect-table-size 4096 conntrack-hash-size 4096 conntrack-table-size 32768 conntrack-tcp-loose enable ipv6-receive-redirects disable ipv6-src-route disable ip-src-route disable log-martians enable name LAN_in { rule 100 { action accept description "Default LAN -> any" protocol all source { address 10.0.0.0/24 } } } name LAN_out { } name LOCAL { rule 100 { action accept state { established enable } } } name WAN_in { rule 20 { action accept description "Allow SMTP connections to MX01" destination { address 74.XXX.XXX.XXX port 25 } protocol tcp } rule 100 { action accept description "Allow established connections back through" state { established enable } } } name WAN_out { } receive-redirects disable send-redirects enable source-validation disable syn-cookies enable SIDENOTE To test for open ports I have using this website, http://www.yougetsignal.com/tools/open-ports/, it showed port 25 as open without the firewall rules and closed with the firewall rules. UPDATE Just to see if the firewall was working properly I made a rule to block SSH from the WAN interface. When I checked for port 22 on my primary WAN address it said it was still open even though I outright blocked the port. Here is the rule I used; rule 21 { action reject destination { address 74.219.80.163 port 22 } protocol tcp } So now I am convinced either I am doing something wrong or the firewall is not working like it should.

  Read the article

• CommunicationException when shutting down JBoss 4.2.2

  - by Brian

  I have deployed an application using JBoss 4.2.2 on a 64-bit RHEL5 server. Since there are other JBoss servers, I had to change some port configurations so that there would be no conflicts when starting the server. So right now I'm using ports-01 from the sample-bindings.xml file that came in the docs/examples/binding-manager/samples directory. In addition, below is a list of all the files I've edited to reflect the new ports: JBOSS_HOME/servers/default/deploy/jboss-web.deployer/server.xml: Changed Connector port - 8080 to 8180 Changed AJP 1.3 Connector port - 8009 to 8109 JBOSS_HOME/server/default/deploy/jbossws.beans/META-INF/jboss-beans.xml Changed 8080 to 8180 JBOSS_HOME/server/default/conf/jboss-service.xml: Changed 8083 to 8183 Changed 1099 to 1299 Changed 1098 to 1298 Changed 4444 to 4644 Changed 4445 to 4645 Changed 4446 to 4646 Changed 4447 to 4647 JBOSS_HOME/server/default/conf/jboss-minimal.xml: Changed 1099 to 1299 Changed 1098 to 1298 When I start the server (binding to localhost) everything is fine and I'm able to access the application. But when I try to shutdown the server I get the following error: Exception in thread "main" javax.naming.CommunicationException: Could not obtain connection to any of these urls: localhost [Root exception is javax.naming.CommunicationException : Failed to connect to server localhost:1099 [Root exception is javax.naming.ServiceUnavailableException: Failed to connect to server localhost:1099 [Root exception is java.net.ConnectException: Connection refused]]] at org.jnp.interfaces.NamingContext.checkRef(NamingContext.java:1562) at org.jnp.interfaces.NamingContext.lookup(NamingContext.java:634) at org.jnp.interfaces.NamingContext.lookup(NamingContext.java:627) at javax.naming.InitialContext.lookup(InitialContext.java:392) at org.jboss.Shutdown.main(Shutdown.java:214) Caused by: javax.naming.CommunicationException: Failed to connect to server localhost:1099 [Root exception is javax.naming.ServiceUnavailableException: Failed to connect to server localhost:1099 [Root exception is java.net.ConnectException: Connection refused]] at org.jnp.interfaces.NamingContext.getServer(NamingContext.java:274) at org.jnp.interfaces.NamingContext.checkRef(NamingContext.java:1533) ... 4 more Caused by: javax.naming.ServiceUnavailableException: Failed to connect to server localhost:1099 [Root exception is java.net.ConnectException: Connection refused] at org.jnp.interfaces.NamingContext.getServer(NamingContext.java:248) ... 5 more Caused by: java.net.ConnectException: Connection refused at java.net.PlainSocketImpl.socketConnect(Native Method) at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:333) at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:195) at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:182) at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366) at java.net.Socket.connect(Socket.java:525) at java.net.Socket.connect(Socket.java:475) at java.net.Socket.(Socket.java:372) at java.net.Socket.(Socket.java:273) at org.jnp.interfaces.TimedSocketFactory.createSocket(TimedSocketFactory.java:84) at org.jnp.interfaces.TimedSocketFactory.createSocket(TimedSocketFactory.java:77) at org.jnp.interfaces.NamingContext.getServer(NamingContext.java:244) ... 5 more Is there any other file that I need to change the 1099 to 1299, or am I missing some other step?

  Read the article

• Wireless 802.11x Disconnects

  - by BillP3rd

  I've looked at (and read) all of the similar questions and none of them get exactly to the issue I'm having at home. I have an 802.11g access point (two, actually, with different SSIDs and on different channels). One is an Airlink AR525W. The other is a Linksys WRT54G v.2. The issue is that at random times, my laptop will lose its wireless connection. This occurs regardless of which access point I'm connected to. When I lose the connection, the affected AP no longer appears in the list of available APs. Also, it doesn't have anything to do with walls or distance. It can happen within 30' and when my laptop is literally within line-of-sight. When it loses the signal, it can take from 10 to 30 minutes to reconnect and it always will without intervention. I've done all the “standard” things to troubleshoot the problem and it has improved. For example, I surveyed other access points in my vicinity and have selected a different channel for each of my APs that no one else nearby is using. Both APs are configured WPA2/AES. I'm down to wondering [Note: This is not a shopping question. I'm not buying a new AP] if the fact that I didn't drop two bills on my APs and instead opted for more modest solutions has anything to do with it? I've oft wondered why anyone would go for the high-end AP when they didn't have to. Also, I am aware of DD-WRT and have chosen not to go there because only one of my APs is supported. Oh, and one final thing. It an HP x64 laptop running Windows 7 Ultimate. The wireless interface is an Atheros AR9285 802.11b/g/n WiFi Adapter. All the latest drivers and service packs have been applied. It did the same thing with my old laptop (a Lenovo) so I don't the problem is in the laptop. It's really annoying when this happens and suggestions of things I haven't thought of or may have overlooked (No, really. As unlikely as it is, I admit that I may have overlooked something :-)) are appreciated.

  Read the article

• recommendations for efficient offsite remote backup solution of vm's

  - by senorsmile

  I am looking for recommendations for backing up my current 6 vm's(and soon to grow to up to 20). Currently I am running a two node proxmox cluster(which is a debian base using kvm for virtualization with a custom web front end to administer). I have two nearly identical boxes with amd phenom II x4's and asus motherboards. Each has 4 500 GB sata2 hdd's, 1 for the os and other data for the proxmox install, and 3 using mdadm+drbd+lvm to share the 1.5 TB's of storage between the two machines. I mount lvm images to kvm for all of the virtual machines. I currently have the ability to do live transfer from one machine to the other, typically within seconds(it takes about 2 minutes on the largest vm running win2008 with m$ sql server). I am using proxmox's built-in vzdump utility to take snapshots of the vm's and store those on an external harddrive on the network. I then have jungledisk service (using rackspace) to sync the vzdump folder for remote offsite backup. This is all fine and dandy, but it's not very scalable. For one, the backups themselves can take up to a few hours every night. With jungledisk's block level incremental transfers, the sync only transfers a small portion of the data offsite, but that still takes at least a half an hour. The much better solution would of course be something that allows me to instantly take the difference of two time points (say what was written from 6am to 7am), zip it, then send that difference file to the backup server which would instantly transfer to the remote storage on rackspace. I have looked a little into zfs and it's ability to do send/receive. That coupled with a pipe of the data in bzip or something would seem perfect. However, it seems that implementing a nexenta server with zfs would essentially require at least one or two more dedicated storage servers to serve iSCSI block volumes (via zvol's???) to the proxmox servers. I would prefer to keep the setup as minimal as possible (i.e. NOT having separate storage servers) if at all possible. I have also briefly read about zumastor. It looks like it could also do what I want, but it appears to have halted development in 2008. So, zfs, zumastor or other?

  Read the article

• How to configure Transparent IP Address Sharing (TAS) on a Mediatrix 4102 with DGW 2.0 firmware?

  - by Pascal Bourque

  I am making the switch to VoIP. I chose voip.ms as my service provider and Mediatrix 4102 as my ATA. One reason why I chose the Mediatrix over other popular consumer ATAs is that it's supposed to be easy to place it in front of the router, so it can give priority to its own upstream traffic over the home network's upstream traffic. This is supposed to work transparently, with the ATA and router sharing the same public IP address (the one obtained from the modem). They call this feaure Transparent IP Address Sharing, or TAS. Their promotional brochure describes it like this: The Mediatrix 4102 also uses its innovative TAS (Transparent IP Address Sharing) technology and an embedded PPPoE client to allow the PC (or router) connected to the second Ethernet port to have the same public IP address, eliminating the need for private IP addresses or address translations. I am interested by this feature because my router, an Apple Time Capsule, doesn't support QoS and cannot give priority to the voice packets if the ATA is behind the router. However, after hours of searching the web, reading the documentation, and good ol' trial and error, I haven't been able to configure the Mediatrix to run in this mode. Then I found a version of the manual that looks like it was for a previous version of the firmware (SIP), where there is an entire section dedicated to configuring TAS (starting at page 209). But my Mediatrix comes with the DGW 2.0 firmware, whose documentation does not mention TAS at all. So I tried to follow the TAS setup instructions from the SIP documentation and apply them to my DGW firmware, using the Variable Mapping Between SIP v5.0 and DGW v2.0 document as a reference, but no success. Some required SIP variables don't have an equivalent in DGW. So it looks like the DGW firmware does not support TAS at all, or if it does they are not doing anything to help us set it up. So right now, the Mediatrix is behind the router and VoIP works perfectly except when my upstream bandwidth is saturated. My questions are: Is downgrading to SIP firmware the only way to have my Mediatrix 4102 run in TAS mode? If not, anybody knows how to setup TAS on the DGW firmware? Is TAS mode the only way to give priority to the voice packets if I want to keep my current router (Apple Time Capsule)? Thanks!

  Read the article

• "No route to host" with ssl but not with telnet

  - by Clemens Bergmann

  I have a strange problem with connecting to a https site from one of my servers. When I type: telnet puppet 8140 I am presented with a standard telnet console and can talk to the Server as always: Connected to athena.hidden.tld. Escape character is '^]'. GET / HTTP/1.1 <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>400 Bad Request</title> </head><body> <h1>Bad Request</h1> <p>Your browser sent a request that this server could not understand.<br /> Reason: You're speaking plain HTTP to an SSL-enabled server port.<br /> Instead use the HTTPS scheme to access this URL, please.<br /> <blockquote>Hint: <a href="https://athena.hidden.tld:8140/"><b>https://athena.hidden.tld:8140/</b></a></blockquote></p> <hr> <address>Apache/2.2.16 (Debian) Server at athena.hidden.tld Port 8140</address> </body></html> Connection closed by foreign host. But when I try to connect to the same host and port with ssl: openssl s_client -connect puppet:8140 It is not working connect: No route to host connect:errno=113 I am confused. At first it sounded like a firewall problem but this could not be, could it? Because this would also prevent the telnet connection. As Firewall I am using ferm on both servers. The systems are debian squeeze vm-boxes. [edit 1] Even when I try to connect directly with the IP address: openssl s_client -connect 198.51.100.1:8140 #address exchanged connect: No route to host connect:errno=113 Bringing down the firewalls on both hosts with service ferm stop is also not helping. But when I do openssl s_client -connect localhost:8140 on the server machine it is connecting fine. [edit 2] if I connect to the IP with telnet it also is not working. telnet 198.51.100.1 8140 Trying 198.51.100.1... telnet: Unable to connect to remote host: No route to host The confusion might come from IPv6. I have IPv6 on all my hosts. It seems that telnet uses IPv6 by default and this works. For example: telnet -6 puppet 8140 works but telnet -4 puppet 8140 does not work. So there seems to be a problem with the IPv4 route. openssl seems to only (or by default) use IPv4 and therefore fails but telnet uses IPv6 and succeeds.

  Read the article

• Glassfish V3 won't start

  - by Thierry

  I installed NetBeans 6.8 and tried to run the GlasshFish V3 server. I'm working under Windows Vista 32 Bits. First, it won't run. Then I modified the c:\Windows\System32\drivers\etc\hosts file and put the following line into it: 127.0.0.1 localhost And when I run the GlasshFish V3 Server, no error is showing but only "INFOs" are displayed: 3 avr. 2010 19:23:19 com.sun.enterprise.glassfish.bootstrap.ASMain main INFO: Launching GlassFish on Felix platform Welcome to Felix ================ INFO: Perform lazy SSL initialization for the listener 'http-listener-2' INFO: Starting Grizzly Framework 1.9.18-k - Sat Apr 03 19:23:24 CEST 2010 INFO: Starting Grizzly Framework 1.9.18-k - Sat Apr 03 19:23:25 CEST 2010 INFO: Grizzly Framework 1.9.18-k started in: 423ms listening on port 35127 INFO: GlassFish v3 (74.2) startup time : Felix(4456ms) startup services(1709ms) total(6165ms) INFO: Grizzly Framework 1.9.18-k started in: 459ms listening on port 35116 INFO: Grizzly Framework 1.9.18-k started in: 428ms listening on port 35155 INFO: Grizzly Framework 1.9.18-k started in: 470ms listening on port 35160 INFO: Grizzly Framework 1.9.18-k started in: 513ms listening on port 35159 INFO: javassist.util.proxy.ProxyFactory.classLoaderProvider = org.glassfish.weld.WeldActivator$GlassFishClassLoaderProvider@5be8f4 INFO: Hibernate Validator bean-validator-3.0-JBoss-4.0.2 INFO: Binding RMI port to *:35165 INFO: Instantiated an instance of org.hibernate.validator.engine.resolver.JPATraversableResolver. INFO: JMXStartupService: Started JMXConnector, JMXService URL = service:jmx:rmi://PC-de-Charlotte:35165/jndi/rmi://PC-de-Charlotte:35165/jmxrmi INFO: Using com.sun.enterprise.transaction.jts.JavaEETransactionManagerJTSDelegate as the delegate INFO: [Thread[GlassFish Kernel Main Thread,5,main]] started INFO: Grizzly Framework 1.9.18-k started in: 150ms listening on port 35159 INFO: Perform lazy SSL initialization for the listener 'http-listener-2' INFO: {felix.fileinstall.poll (ms) = 5000, felix.fileinstall.dir = C:\Program Files\sges-v3\glassfish\modules\autostart, felix.fileinstall.debug = 1, felix.fileinstall.bundles.new.start = true, felix.fileinstall.tmpdir = C:\Users\CHARLO~1\AppData\Local\Temp\fileinstall-330907148519261411, felix.fileinstall.filter = null} INFO: {felix.fileinstall.poll (ms) = 5000, felix.fileinstall.dir = C:\Users\Charlotte\.netbeans\6.8\GlassFish_v3\autodeploy\bundles, felix.fileinstall.debug = 1, felix.fileinstall.bundles.new.start = true, felix.fileinstall.tmpdir = C:\Users\CHARLO~1\AppData\Local\Temp\fileinstall-2938963288421854459, felix.fileinstall.filter = null} INFO: Grizzly Framework 1.9.18-k started in: 95ms listening on port 35160 INFO: Updating configuration from org.apache.felix.fileinstall-autodeploy-bundles.cfg INFO: Installed C:\Program Files\sges-v3\glassfish\modules\autostart\org.apache.felix.fileinstall-autodeploy-bundles.cfg INFO: {felix.fileinstall.poll (ms) = 5000, felix.fileinstall.dir = C:\Users\Charlotte\.netbeans\6.8\GlassFish_v3\autodeploy\bundles, felix.fileinstall.debug = 1, felix.fileinstall.bundles.new.start = true, felix.fileinstall.tmpdir = C:\Users\CHARLO~1\AppData\Local\Temp\fileinstall-6474085409014899009, felix.fileinstall.filter = null} And there is no message such as "Glassfish started"! So, when I try to access to the admin web interface: localhost:4848 or localhost:8080 or localhost:8181 , It doesn't work. What should I do? Thank you very much, Regards.

  Read the article

• Exchange 2007 and migrating only some users under a shared domain name

  - by DomoDomo

  I'm in the process of moving two law firms to hosted Exchange 2007, a service that the consulting company I work for offers. Let's call these two firms Crane Law and Poole Law. These two firms were ONE firm just six months ago, but split. So they have three email domains: Old Firm: craneandpoole.com New Firm 1: cranelaw.com New Firm 2: poolelaw.com Both Firm 1 & Firm 2 use craneandpoole.com email addresses, as for the other two domains, only people who work at the respective firm use that firm's domain name, natch. Currently these two firms are still using the same pre-split internal Exchange 2007 server, where MX records for all three domains point. Here's the problem. I'm not moving both companies at the same time. I'm moving Crane Law two weeks before Poole Law. During this two weeks, both companies need to be able to: Continue to receive emails addressed to craneandpoole.com Send emails between firms, using cranelaw.com and poolelaw.com accounts I also have a third problem: I'd like to setup all three domains in my hosting infrastructure way ahead of time, to make my own life easier What would solve all my problems would be, if there is some way I can tell Exchange 2007, even though this domain exists locally forward on the message to the outside world using public MX record as a basis for where to send it (or if I could somehow create a route for it statically that would work too). If this doesn't work, to address points #1 when I migrate Crane Law, I will delete all references locally to cranelaw.com on their current Exchange server, and setup individual forwards for each of their craneandpool.com mailboxes to forward to our hosted exchange server. This will also take care of point #2, since the cranelaw.com won't be there locally, when poolelaw.com tries to send to cranelaw.com, public MX records will be used for mail routing decisions and go to my hosted exchange. The bummer of that though is, I won't be able to setup poolelaw.com ahead of time in hosted Exchange, will have to wait to do it day of :( Sorry for the long and confusing post. Just wondering if there is a better or simpler way to do what I want? Three tier forests and that kind of thing are out, this is just a two week window where they won't be in the same place.

  Read the article

• Problems when trying to connect to a router wirelessly

  - by Ruud Lenders

  The situation - At my girlfriend's parents' place there are six Windows 7 devices that are wired or wireless connected to a router: 3 dekstops and 3 laptops. There are also several smartphones using the router. The router is secured with WPA2 (AES). The problem - We never had any problems with the router for over a year. But recently - about 3 weeks ago - my girlfriend's laptop (HP) and my laptop (ASUS) started to develop problems while trying to connect to the router. The router has stopped showing up from the network list. Sometimes it comes back and shows up, but then it keeps saying something along the lines of "Could not connect", and not long after that it dissapears again. The range of the router is not the problem here, because we experience the same when we sit next to the router. Sometimes, if we are lucky, and waited a long time (10-15 minutes) without using the laptop for anything, the laptop will eventually succesful connect to the router. The attempts - Of course, the Window 7 troubleshooter. We tried troubleshooting the connection problems and the wireless network adapter, but no luck. We also reset the router enough times to know that's not helping either. Here's the full list of things we tried, but did not help: Running the Windows 7 troubleshooter Resetting the router (more than once) Setting the router settings to factory defaults Disconnecting all other devices except one laptop Applying a system restore Trying static/dynamic IP/DNS - Dynamic is better, right? Enabling/disabling IPv6 - Should I keep IPv6 disabled? Running the command: netsh wlan stop hostednetwork Running the command: netsh wlan set hostednetwork mode=disallow Updating/reïnstalling wireless adapter drivers The tests - To help finding the core of the problem, we tested the following: Plugging an ethernet cable in the router and in our laptops - worked fine Connecting someone else's laptop to the router (wireless) - worked fine Connecting our laptops to someone else's router - worked fine The router - This information might be relevant: Router model: Sitecom 300N Wireless Router Router hardware: version 01 The DCHP Server's IPs range from 192.168.0.100 to 192.168.0.200. Router settings: Wireless channel: 12 Channel bandwidth: 20/40 MHz Extension channel: 8 Preamble type: Long 802.11g protection: Disabled UPnP: Enabled The laptops - If you are wondering about our laptops: My laptop model: ASUS Pro64JQ Girlfriend's laptop: HP Pavillion G6 OS: Both Windows 7 Professional x64 - with Service Pack 1 My wireless adapter: Atheros AR9285 AdHoc 11n: Enabled The question - Does anyone have experienced the same problems as I do? Or does someone know how to solve this? Are there more tricks I can try, or settings I should change? Note - Our laptops are not slow or old. My laptop is 1.5 years old, and the other laptop is just 5 months old. I know how to keep laptops clean and I'm pretty sure both laptops are not bloated with useless software.

  Read the article

• Establishing a web page bookmarking process - looking for ideas to improve

  - by Matt

  Like many others, I have a process for bookmarking web pages to read later. My requirements for web page bookmarking are: Ability to bookmark pages must be available from all (within reason) platforms - PC/browser, mobile device, etc. Bookmarks must be centrally stored (implicit from #2) so that I can read the bookmarks from anywhere/any device Full text of web pages must be stored Bonus features would be: Bookmarks and page content should be full text searchable Maintain an archive indefinitely Distinguish between what's read vs. unread Bookmarked page content is cleaned up, e.g. ads eliminated, unnecessary html removed, pages better formatted for reading My current process (which addresses most of these requirements) is as follows: I set up a Gmail account with 2 labels, "Bookmarks Unread" and "Bookmarks Read" Gmail filters set up such that depending on the form of the address (using Gmail's '+string' functionality in addresses), the incoming bookmark gets labeled appropriately On each of my browsers/devices, I have an address book entry for [email protected] and [email protected]. If I want to clean up the page content, I use the Readability bookmarklet which does a great job of giving me the essential content only Anywhere I have Firefox, I use the Send Page by Email extension which, with 2 clicks, allows me to send the cleaned-up Readability page URL and content to one of the above email addresses. Where I don't have Firefox (e.g. iPhone or other mobile device) I use the native ability to send the current link via email (most/all apps have them, including the browser, RSS readers, NYTimes, etc.). In most cases (unless it's built into the particular app), this won't include the page body. The process is almost perfect. I've got the central access and ubiquitous access of Gmail as the storage mechanism, full text searchability (due to Gmail, but of course only for the URLs I send from that Firefox extension), a cleaned up page due to Readability, ability to read offline (assuming I use an IMAP client against Gmail) and permanent archiving of content, including what's been read vs. unread. The missing pieces are: The Send Page by Email Firefox extension seems to only send X bytes of a web page. Or some portion. So it limits my full text searchability. Where I don't have Firefox, I can only send the link, so no full text search at all in those cases. Instapaper looks like it meets most of my requirements (and bonus items). The only downside to me (personal preference) is that central storage is based on Instapaper vs. something more broad like Gmail, which as a generalized service and with Google behind it pretty much means it's permanent. I'm not too hung up on this, but I would definitely prefer to keep Gmail if possible. An upside of Instapaper is that it does the page clean-up as well as stores the entire page content, unlike my Firefox extension. Thoughts on addressing the gaps and improving this process further?

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter EDIT: I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  EDIT: I thought I pinpointed the problem. Just now I tried to go to the firefox addons page which uses https and gmail also uses https. So I thought I am unable to load https pages on this computer. So I went to a bank site which uses https but that loads just fine. Sigh.... I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• Explanation of the init.d/scripts Fedora

  - by Shahmir Javaid

  Below is a copy of vsftpd, i need some explanations of some of the scripts mentioned below in this script: #!/bin/bash # ### BEGIN INIT INFO # Provides: vsftpd # Required-Start: $local_fs $network $named $remote_fs $syslog # Required-Stop: $local_fs $network $named $remote_fs $syslog # Short-Description: Very Secure Ftp Daemon # Description: vsftpd is a Very Secure FTP daemon. It was written completely from # scratch ### END INIT INFO # vsftpd This shell script takes care of starting and stopping # standalone vsftpd. # # chkconfig: - 60 50 # description: Vsftpd is a ftp daemon, which is the program \ # that answers incoming ftp service requests. # processname: vsftpd # config: /etc/vsftpd/vsftpd.conf # Source function library. . /etc/rc.d/init.d/functions # Source networking configuration. . /etc/sysconfig/network RETVAL=0 prog="vsftpd" start() { # Start daemons. # Check that networking is up. [ ${NETWORKING} = "no" ] && exit 1 [ -x /usr/sbin/vsftpd ] || exit 1 if [ -d /etc/vsftpd ] ; then CONFS=`ls /etc/vsftpd/*.conf 2>/dev/null` [ -z "$CONFS" ] && exit 6 for i in $CONFS; do site=`basename $i .conf` echo -n $"Starting $prog for $site: " daemon /usr/sbin/vsftpd $i RETVAL=$? echo if [ $RETVAL -eq 0 ]; then touch /var/lock/subsys/$prog break else if [ -f /var/lock/subsys/$prog ]; then RETVAL=0 break fi fi done else RETVAL=1 fi return $RETVAL } stop() { # Stop daemons. echo -n $"Shutting down $prog: " killproc $prog RETVAL=$? echo [ $RETVAL -eq 0 ] && rm -f /var/lock/subsys/$prog return $RETVAL } # See how we were called. case "$1" in start) start ;; stop) stop ;; restart|reload) stop start RETVAL=$? ;; condrestart|try-restart|force-reload) if [ -f /var/lock/subsys/$prog ]; then stop start RETVAL=$? fi ;; status) status $prog RETVAL=$? ;; *) echo $"Usage: $0 {start|stop|restart|try-restart|force-reload|status}" exit 1 esac exit $RETVAL Question I What the hell is the difference between the && and || signs in the below commands, and is it just an easy way to do a simple if check or is it completely different to a if[..something..]; then ..something.. fi: # Check that networking is up. [ ${NETWORKING} = "no" ] && exit 1 [ -x /usr/sbin/vsftpd ] || exit 1 Question II i get what -eq and -gt is (equal to, greater than) but is there a simple website that explains what -x, -d and -f are? Any help would be apreciated Running Fedora 12 on my OS. Script copied from /etc/init.d/vsftpd Question III It says required starts are $local_fs $network $named $remote_fs $syslog but i cant see any where it checks for those.

  Read the article

• My hosting server giving memory allocation error

  - by Usman

  I have hosted my website on shared hosting linux server. As there are atmost 10-15 visitors come to my website daily but My wordpress website most of the times gives 500 Internal Server Error. I accessed my server Error Log following error is showing: [Tue Dec 04 08:57:45 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:45 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:43 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:43 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:42 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:42 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:41 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:41 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:40 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:40 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:32 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:31 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:29 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:29 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:26 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php Is my hosting service really bad. And any solution. Thanks in advance.

  Read the article

• How to configure Transparent IP Address Sharing (TAS) on a Mediatrix 4102 with DGW 2.0 firmware?

  - by Pascal Bourque

  I am making the switch to VoIP. I chose voip.ms as my service provider and Mediatrix 4102 as my ATA. One reason why I chose the Mediatrix over other popular consumer ATAs is that it's supposed to be easy to place it in front of the router, so it can give priority to its own upstream traffic over the home network's upstream traffic. This is supposed to work transparently, with the ATA and router sharing the same public IP address (the one obtained from the modem). They call this feaure Transparent IP Address Sharing, or TAS. Their promotional brochure describes it like this: The Mediatrix 4102 also uses its innovative TAS (Transparent IP Address Sharing) technology and an embedded PPPoE client to allow the PC (or router) connected to the second Ethernet port to have the same public IP address, eliminating the need for private IP addresses or address translations. I am interested by this feature because my router, an Apple Time Capsule, doesn't support QoS and cannot give priority to the voice packets if the ATA is behind the router. However, after hours of searching the web, reading the documentation, and good ol' trial and error, I haven't been able to configure the Mediatrix to run in this mode. Then I found a version of the manual that looks like it was for a previous version of the firmware (SIP), where there is an entire section dedicated to configuring TAS (starting at page 209). But my Mediatrix comes with the DGW 2.0 firmware, whose documentation does not mention TAS at all. So I tried to follow the TAS setup instructions from the SIP documentation and apply them to my DGW firmware, using the Variable Mapping Between SIP v5.0 and DGW v2.0 document as a reference, but no success. Some required SIP variables don't have an equivalent in DGW. So it looks like the DGW firmware does not support TAS at all, or if it does they are not doing anything to help us set it up. So right now, the Mediatrix is behind the router and VoIP works perfectly except when my upstream bandwidth is saturated. My questions are: Is downgrading to SIP firmware the only way to have my Mediatrix 4102 run in TAS mode? If not, anybody knows how to setup TAS on the DGW firmware? Is TAS mode the only way to give priority to the voice packets if I want to keep my current router (Apple Time Capsule)? Thanks!

  Read the article

• Cisco ASA SSL VPN options?

  - by JonH

  Disclaimer: I am not a network admin so I may be wrong here but I thought asking here would help. I'm a developer mainly on the .net framework as well as helping get a mobile intranet app working. Because this app is only allowed to be used on our network I can easily run this app on our wireless network connection within our building. All is fine and dandy but we'd also like to be able to run this mobile app at say a customer plant using VPN software. I thought surely this could be easy as we exclusively use Samsung s4 phones so I thought I'd download Cisco's Samsung any connect software to allow us to VPN...its right on the play store. Sure enough it doesn't work. I mention it to our network admin who says not possible since we have old technology that doesn't support SSL. He mentions we'd have to upgrade all of our hardware, the firewall, etc. to get this to work. We really need VPN on our phones not only for this app but other internal apps, etc. He did mention the following: We can’t upgrade the software on our ASA, because we don’t have enough memory for the new version.  (the asa is very old).  We can’t add more memory, so we would have to get a new firewall, which I have been told I cannot do. In addition he also mentioned: The Samsung AnyConnect client uses SSL to connect.  With the current (old) version of software that our firewall is running, the SSL connections are unreliable.  We need different hardware in order to upgrade our firewall, which we are unable to attain at this time.  This is the same reason that Windows 8 clients are not able to connect. I am curious hence me asking. vpns seem to be fairly simple to setup. What other options do I have aside from making this a public site or web service that consumes this data over the internet as this is a complete no no. What can we do to make this work without that much effort or cost.

  Read the article

• iptables management tools for large scale environment

  - by womble

  The environment I'm operating in is a large-scale web hosting operation (several hundred servers under management, almost-all-public addressing, etc -- so anything that talks about managing ADSL links is unlikely to work well), and we're looking for something that will be comfortable managing both the core ruleset (around 12,000 entries in iptables at current count) plus the host-based rulesets we manage for customers. Our core router ruleset changes a few times a day, and the host-based rulesets would change maybe 50 times a month (across all the servers, so maybe one change per five servers per month). We're currently using filtergen (which is balls in general, and super-balls at our scale of operation), and I've used shorewall in the past at other jobs (which would be preferable to filtergen, but I figure there's got to be something out there that's better than that). The "musts" we've come up with for any replacement system are: Must generate a ruleset fairly quickly (a filtergen run on our ruleset takes 15-20 minutes; this is just insane) -- this is related to the next point: Must generate an iptables-restore style file and load that in one hit, not call iptables for every rule insert Must not take down the firewall for an extended period while the ruleset reloads (again, this is a consequence of the above point) Must support IPv6 (we aren't deploying anything new that isn't IPv6 compatible) Must be DFSG-free Must use plain-text configuration files (as we run everything through revision control, and using standard Unix text-manipulation tools are our SOP) Must support both RedHat and Debian (packaged preferred, but at the very least mustn't be overtly hostile to either distro's standards) Must support the ability to run arbitrary iptables commands to support features that aren't part of the system's "native language" Anything that doesn't meet all these criteria will not be considered. The following are our "nice to haves": Should support config file "fragments" (that is, you can drop a pile of files in a directory and say to the firewall "include everything in this directory in the ruleset"; we use configuration management extensively and would like to use this feature to provide service-specific rules automatically) Should support raw tables Should allow you to specify particular ICMP in both incoming packets and REJECT rules Should gracefully support hostnames that resolve to more than one IP address (we've been caught by this one a few times with filtergen; it's a rather royal pain in the butt) The more optional/weird iptables features that the tool supports (either natively or via existing or easily-writable plugins) the better. We use strange features of iptables now and then, and the more of those that "just work", the better for everyone.

  Read the article

< Previous Page | 753 754 755 756 757 758 759 760 761 762 763 764  | Next Page >