Search Results

Search found 2031 results on 82 pages for '37 signals'.

Page 76/82 | < Previous Page | 72 73 74 75 76 77 78 79 80 81 82  | Next Page >

  • Figuring out the performance limitation of an ADC on a PIC microcontroller

    - by AKE
    I'm spec-ing the suitability of a microcontroller like PIC for an analog-to-digital application. This would be preferable to using external A/D chips. To do that, I've had to run through some computations, pulling the relevant parameters from the datasheets. I'm not sure I've got it right -- would appreciate a check! Here's the simplest example: PIC10F220 is the simplest possible PIC with an ADC. Runs at clock speed of 8MHz. Has an instruction cycle of 0.5us (4 clock steps per instruction) So: Taking Tacq = 6.06 us (acquisition time for ADC, assume chip temp. = 50*C) [datasheet p34] Taking Fosc = 8MHz (? clock speed) Taking divisor = 4 (4 clock steps per CPU instruction) This gives TAD = 0.5us (TAD = 1/(Fosc/divisor) ) Conversion time is 13*TAD [datasheet p31] This gives conversion time 6.5us ADC duration is then 12.56 us [? Tacq + 13*TAD] Assuming at least 2 instructions for load/store: This is another 1 us [0.5 us per instruction] Which would give max sampling rate of 73.7 ksps (1/13.56) Supposing 8 more instructions for real-time processing: This is another 4 us Thus, total ADC/handling time = 17.56us (12.56us + 1us + 4us) So expected upper sampling rate is 56.9 ksps. Nyquist frequency for this sampling rate is therefore 28 kHz. If this is right, it suggests the (theoretical) performance suitability of this chip's A/D is for signals that are bandlimited to 28 kHz. Is this a correct interpretation of the information given in the data sheet? Any pointers would be much appreciated! AKE

    Read the article

  • How do I repair the corrupted files found by sfc /scannow? "Windows Resource Protection found corrupt files but was unable to fix some of them."

    - by galacticninja
    After running chkdsk C: /F /R and finding out that my hard disk has 24 KB in bad sectors (log is posted below), I decided to run Windows 7's System File Checker utility (sfc /scannow). SFC showed the ff. message after I ran it: "Windows Resource Protection found corrupt files but was unable to fix some of them. Details are included in the CBS.Log windir\Logs\CBS\CBS.log." Since the CBS.log file is too large, I ran findstr /c:"[SR]" %windir%\Logs\CBS\CBS.log >"%userprofile%\Desktop\sfcdetails.txt" (as per Microsoft's KB 928228 article) to only get the log text pertaining to the corrupt files. (log is also posted below) How do I troubleshoot and repair the corrupted files mentioned by sfc /scannow? My OS is Windows 7, 64-bit. chkdsk log Checking file system on C: The type of the file system is NTFS. A disk check has been scheduled. Windows will now check the disk. CHKDSK is verifying files (stage 1 of 5)... 936192 file records processed. File verification completed. 25238 large file records processed. 0 bad file records processed. 4 EA records processed. 44 reparse records processed. CHKDSK is verifying indexes (stage 2 of 5)... 1051640 index entries processed. Index verification completed. 0 unindexed files scanned. 0 unindexed files recovered. CHKDSK is verifying security descriptors (stage 3 of 5)... 936192 file SDs/SIDs processed. Cleaning up 24 unused index entries from index $SII of file 0x9. Cleaning up 24 unused index entries from index $SDH of file 0x9. Cleaning up 24 unused security descriptors. Security descriptor verification completed. 57725 data files processed. CHKDSK is verifying Usn Journal... 36994248 USN bytes processed. Usn Journal verification completed. CHKDSK is verifying file data (stage 4 of 5)... 936176 files processed. File data verification completed. CHKDSK is verifying free space (stage 5 of 5)... 306238 free clusters processed. Free space verification is complete. Adding 1 bad clusters to the Bad Clusters File. Correcting errors in the Volume Bitmap. Windows has made corrections to the file system. 488282111 KB total disk space. 485595420 KB in 766458 files. 401856 KB in 57726 indexes. 24 KB in bad sectors. 1059863 KB in use by the system. 65536 KB occupied by the log file. 1224948 KB available on disk. 4096 bytes in each allocation unit. 122070527 total allocation units on disk. 306237 allocation units available on disk. Internal Info: 00 49 0e 00 81 93 0c 00 34 01 17 00 00 00 00 00 .I......4....... 6b 29 00 00 2c 00 00 00 00 00 00 00 00 00 00 00 k)..,........... 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ sfc /scannow log (through findstr /c:"[SR]" %windir%\Logs\CBS\CBS.log >"%userprofile%\Desktop\sfcdetails.txt") Note: The full log is at http://pastebin.com/raw.php?i=gTEGZmWj . I've only quoted parts of the full log below (mostly from the last part), as the full log won't fit within the character limit for questions. I've added it to serve as a preview. ... 2013-12-28 19:37:50, Info CSI00000542 [SR] Beginning Verify and Repair transaction 2013-12-28 19:37:55, Info CSI00000544 [SR] Verify complete 2013-12-28 19:37:56, Info CSI00000545 [SR] Verifying 95 (0x000000000000005f) components 2013-12-28 19:37:56, Info CSI00000546 [SR] Beginning Verify and Repair transaction 2013-12-28 19:38:03, Info CSI00000548 [SR] Verify complete 2013-12-28 19:38:03, Info CSI00000549 [SR] Repairing 43 (0x000000000000002b) components 2013-12-28 19:38:03, Info CSI0000054a [SR] Beginning Verify and Repair transaction ... 2013-12-28 19:38:15, Info CSI00000730 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:62{31}]"GroupPolicy-Admin-Gpedit-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000733 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:30{15}]"frs-core-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000736 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:26{13}]"gpmgmt-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000739 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:74{37}]"MediaServer-ASPAdmin-Migration-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000073c [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:36{18}]"Ldap-Client-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000073f [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:38{19}]"iSNS_Service-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000742 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:76{38}]"MediaServer-Multicast-Migration-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000745 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:78{39}]"Kerberos-Key-Distribution-Center-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000748 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:86{43}]"GroupPolicy-CSE-SoftwareInstallation-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000074b [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:28{14}]"ieframe-dl.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000074e [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:76{38}]"GroupPolicy-Admin-Gpedit-Snapin-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000751 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:32{16}]"IPSec-Svc-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000754 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:22{11}]"HTTP-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000757 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:56{28}]"MediaServer-Migration-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000075a [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:26{13}]"GPBase-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000075d [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:38{19}]"IasMigPlugin-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000760 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:50{25}]"International-Core-DL.man"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000762 [SR] Cannot repair member file [l:24{12}]"wbemdisp.dll" of Microsoft-Windows-WMI-Scripting, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI00000763 [SR] This component was referenced by [l:202{101}]"Microsoft-Windows-Foundation-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.WindowsFoundationDelivery" 2013-12-28 19:38:16, Info CSI00000766 [SR] Could not reproject corrupted file [ml:58{29},l:56{28}]"\??\C:\Windows\SysWOW64\wbem"\[l:24{12}]"wbemdisp.dll"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000768 [SR] Cannot repair member file [l:56{28}]"Microsoft.MediaCenter.UI.dll" of Microsoft.MediaCenter.UI, Version = 6.1.7601.17514, pA = PROCESSOR_ARCHITECTURE_MSIL (8), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI00000769 [SR] This component was referenced by [l:176{88}]"Microsoft-Windows-MediaCenter-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.MediaCenter" 2013-12-28 19:38:16, Info CSI0000076c [SR] Could not reproject corrupted file [ml:520{260},l:40{20}]"\??\C:\Windows\ehome"\[l:56{28}]"Microsoft.MediaCenter.UI.dll"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI0000076e [SR] Cannot repair member file [l:24{12}]"ReAgentc.exe" of Microsoft-Windows-WinRE-RecoveryTools, Version = 6.1.7601.17514, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI0000076f [SR] This component was referenced by [l:202{101}]"Microsoft-Windows-Foundation-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.WindowsFoundationDelivery" 2013-12-28 19:38:16, Info CSI00000772 [SR] Could not reproject corrupted file [ml:48{24},l:46{23}]"\??\C:\Windows\SysWOW64"\[l:24{12}]"ReAgentc.exe"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000774 [SR] Cannot repair member file [l:82{41}]"System.Management.Automation.dll-Help.xml" of Microsoft-Windows-PowerShell-PreLoc.Resources, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture = [l:10{5}]"en-US", VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI00000775 [SR] This component was referenced by [l:266{133}]"Microsoft-Windows-Client-Features-Package~31bf3856ad364e35~amd64~en-US~6.1.7601.17514.Microsoft-Windows-Client-Features-Language-Pack" 2013-12-28 19:38:16, Info CSI00000778 [SR] Could not reproject corrupted file [ml:520{260},l:104{52}]"\??\C:\Windows\System32\WindowsPowerShell\v1.0\en-US"\[l:82{41}]"System.Management.Automation.dll-Help.xml"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI0000077a [SR] Cannot repair member file [l:18{9}]"hlink.dll" of Microsoft-Windows-HLink, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI0000077b [SR] This component was referenced by [l:202{101}]"Microsoft-Windows-Foundation-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.WindowsFoundationDelivery" 2013-12-28 19:38:16, Info CSI0000077e [SR] Could not reproject corrupted file [ml:48{24},l:46{23}]"\??\C:\Windows\SysWOW64"\[l:18{9}]"hlink.dll"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000780 [SR] Repair complete 2013-12-28 19:38:16, Info CSI00000781 [SR] Committing transaction 2013-12-28 19:38:19, Info CSI00000785 [SR] Verify and Repair Transaction completed. All files and registry keys listed in this transaction have been successfully repaired

    Read the article

  • HttpClient POST fails to submit the form + resulting string is cut-off (incomplete)

    - by Jayomat
    Hi, I'm writing an app to check for the bus timetable's. Therefor I need to post some data to a html page, submit it, and parse the resulting page with htmlparser. Though it may be asked a lot, can some one help me identify if 1) this page does support post/get (I think it does) 2) which fields I need to use? 3) How to make the actual request? this is my code so far: String url = "http://busspur02.aseag.de/bs.exe?Cmd=RV&Karten=true&DatumT=30&DatumM=4&DatumJ=2010&ZeitH=&ZeitM=&Suchen=%28S%29uchen&GT0=&HT0=&GT1=&HT1="; String charset = "CP1252"; System.out.println("startFrom: "+start_from); System.out.println("goTo: "+destination); //String tag.v List<NameValuePair> params = new ArrayList<NameValuePair>(); params.add(new BasicNameValuePair("HTO", start_from)); params.add(new BasicNameValuePair("HT1", destination)); params.add(new BasicNameValuePair("GTO", "Aachen")); params.add(new BasicNameValuePair("GT1", "Aachen")); params.add(new BasicNameValuePair("DatumT", day)); params.add(new BasicNameValuePair("DatumM", month)); params.add(new BasicNameValuePair("DatumJ", year)); params.add(new BasicNameValuePair("ZeitH", hour)); params.add(new BasicNameValuePair("ZeitM", min)); UrlEncodedFormEntity query = new UrlEncodedFormEntity(params, charset); HttpPost post = new HttpPost(url); post.setEntity(query); InputStream response = new DefaultHttpClient().execute(post).getEntity().getContent(); // Now do your thing with the facebook response. String source = readText(response,"CP1252"); Log.d(TAG_AVV,response.toString()); System.out.println("STREAM "+source); EDIT: This is my new code: try { HttpClient client = new DefaultHttpClient(); String getURL = "http://busspur02.aseag.de/bs.exe?SID=5FC39&ScreenX=1440&ScreenY=900&CMD=CR&Karten=true&DatumT="+day+"&DatumM="+month+"&DatumJ="+year+"&ZeitH="+hour+"&ZeitM="+min+"&Intervall=60&Suchen=(S)uchen&GT0=Aachen&T0=H&HT0="+start_from+"&GT1=Aachen&T0=H&HT1="+destination+""; HttpGet get = new HttpGet(getURL); HttpResponse responseGet = client.execute(get); HttpEntity resEntityGet = responseGet.getEntity(); if (resEntityGet != null) { //do something with the response Log.i("GET RESPONSE",EntityUtils.toString(resEntityGet)); } } catch (Exception e) { e.printStackTrace(); } But the output file is cut-off. If I do the same request in a browser I get like 14 different routes. Now the file suddenly stops and I only get 3 routes.... what's wrong? 04-30 12:19:12.362: INFO/GET RESPONSE(256): <!-- Ausgabebereich (automatisch erzeugt) --> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <div align="center"> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <p></p> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <p>Ihr Fahrplan für die Verbindung von Aachen, Kaiserplatz nach Aachen, Karlsgraben am Freitag, den 30.04.2010 (Koniginnedag), Abfahrten ab 12:19 Uhr</p> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <table class="Result"> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <tr> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <th class="fussnote">Fussnote</th> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <th class="fahrzeug">Fahrzeug</th> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <th class="abfahrt">Abfahrt</th> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <th class="haltestellean">Haltestelle</th> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <th class="linie">Linie</th> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <th class="haltestelleab">Haltestelle</th> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <th class="ankunft">Ankunft</th> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <th class="fahrzeit">Fahrzeit/Tarif</th> 04-30 12:19:12.362: INFO/GET RESPONSE(256): </tr> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <tr> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <td>&nbsp;</td><td>&nbsp;<img src="http://www.busspur.de/logos/efa-bus.gif" title="Niederflurbus"></td><td>12:23</td><td title="lc0">Aachen, Kaiserplatz [Heinrichsalle Ri. Hansemannplatz]&nbsp;<a href="http://download.avv.de/Umgebungsplaene/hlp_ac_kaiserplatz.pdf">Umgebungsplan</a></td><td>45</td><td title="lc0">Aachen, Karlsgraben&nbsp;<a href="http://download.avv.de/Umgebungsplaene/hlp_ac_karlsgraben.pdf">Umgebungsplan</a></td><td>12:34</td><td>00:11 /  1,00</td><td>&nbsp;</td> 04-30 12:19:12.362: INFO/GET RESPONSE(256): </tr> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <tr><td colspan="9"><a href="/bs.exe?RI=0&amp;SID=5FC39">Fahrtbegleiter</a>&nbsp;&nbsp;</td></tr> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <tr><td colspan="9"><hr></td></tr> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <tr> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <td>&nbsp;</td><td>&nbsp;<img src="http://www.busspur.de/logos/efa-bus.gif" title="Niederflurbus"></td><td>12:26</td><td title="lc0">Aachen, Kaiserplatz [Heinrichsalle Ri. Hansemannplatz]&nbsp;<a href="http://download.avv.de/Umgebungsplaene/hlp_ac_kaiserplatz.pdf">Umgebungsplan</a></td><td>22</td><td title="lc0">Aachen, Karlsgraben&nbsp;<a href="http://download.avv.de/Umgebungsplaene/hlp_ac_karlsgraben.pdf">Umgebungsplan</a></td><td>12:37</td><td>00:11 /  1,00</td><td>&nbsp;</td> 04-30 12:19:12.362: INFO/GET RESPONSE(256): </tr> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <tr><td colspan="9"><a href="/bs.exe?RI=1&amp;SID=5FC39">Fahrtbegleiter</a>&nbsp;&nbsp;</td></tr> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <tr><td colspan="9"><hr></td></tr> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <tr> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <td>&nbsp;</td><td>&nbsp;<img src="http://www.busspur.de/logos/efa-bus.gif" title="Niederflurbus"></td><td>12:28</td><td title="lc0">Aachen, Kaiserplatz [Heinrichsalle Ri. Hansemannplatz]&nbsp;<a href="http://download.avv.de/Umgebungsplaene/hlp_ac_kaiserplatz.pdf">Umgebungsplan</a></td><td>25</td><td title="lc0">Aachen, Karlsgraben&nbsp;<a href="http://download.avv.de/Umgebungsplaene/hlp_ac_karlsgraben.pdf">Umgebungsplan</a></td><td>12:39</td><td>00:11 /  1,00</td><td>&nbsp;</td> 04-30 12:19:12.362: INFO/GET RESPONSE(256): </tr> 04-30 12:19:12.362: INFO/GET RESPONSE(256): <tr><td colspan="9"><a href="/bs.exe?RI=2&amp;SID=5FC39">Fahrtbegl

    Read the article

  • migrating Solaris to RH: network latency issue, tcp window size & other tcp parameters

    - by Bastien
    Hello I have a client/server app (Java) that I'm migrating from Solaris to RH Linux. since I started running it in RH, I noticed some issues related to latency. I managed to isolate the problem that looks like this: client sends 5 messages (32 bytes each) in a row (same application timestamp) to the server. server echos messages. client receives replies and prints round trip time for each msg. in Solaris, all is well: I get ALL 5 replies at the same time, roughly 80ms after having sent original messages (client & server are several thousands miles away from each other: my ping RTT is 80ms, all normal). in RH, first 3 messages are echoed normally (they arrive 80ms after they've been sent), however the following 2 arrive 80ms later (so total 160ms RTT). the pattern is always the same. clearly looked like a TCP problem. on my solaris box, I had previously configured the tcp stack with 2 specific options: disable nagle algorithm globally set tcp_deferred_acks_max to 0 on RH, it's not possible to disable nagle globally, but I disabled it on all of my apps' sockets (TCP_NODELAY). so I started playing with tcpdump (on the server machine), and compared both outputs: SOLARIS: 22 2.085645 client server TCP 56150 > 6006 [PSH, ACK] Seq=111 Ack=106 Win=66672 Len=22 "MSG_1 RCV" 23 2.085680 server client TCP 6006 > 56150 [ACK] Seq=106 Ack=133 Win=50400 Len=0 24 2.085908 client server TCP 56150 > 6006 [PSH, ACK] Seq=133 Ack=106 Win=66672 Len=22 "MSG_2 RCV" 25 2.085925 server client TCP 6006 > 56150 [ACK] Seq=106 Ack=155 Win=50400 Len=0 26 2.086175 client server TCP 56150 > 6006 [PSH, ACK] Seq=155 Ack=106 Win=66672 Len=22 "MSG_3 RCV" 27 2.086192 server client TCP 6006 > 56150 [ACK] Seq=106 Ack=177 Win=50400 Len=0 28 2.086243 server client TCP 6006 > 56150 [PSH, ACK] Seq=106 Ack=177 Win=50400 Len=21 "MSG_1 ECHO" 29 2.086440 client server TCP 56150 > 6006 [PSH, ACK] Seq=177 Ack=106 Win=66672 Len=22 "MSG_4 RCV" 30 2.086454 server client TCP 6006 > 56150 [ACK] Seq=127 Ack=199 Win=50400 Len=0 31 2.086659 server client TCP 6006 > 56150 [PSH, ACK] Seq=127 Ack=199 Win=50400 Len=21 "MSG_2 ECHO" 32 2.086708 client server TCP 56150 > 6006 [PSH, ACK] Seq=199 Ack=106 Win=66672 Len=22 "MSG_5 RCV" 33 2.086721 server client TCP 6006 > 56150 [ACK] Seq=148 Ack=221 Win=50400 Len=0 34 2.086947 server client TCP 6006 > 56150 [PSH, ACK] Seq=148 Ack=221 Win=50400 Len=21 "MSG_3 ECHO" 35 2.087196 server client TCP 6006 > 56150 [PSH, ACK] Seq=169 Ack=221 Win=50400 Len=21 "MSG_4 ECHO" 36 2.087500 server client TCP 6006 > 56150 [PSH, ACK] Seq=190 Ack=221 Win=50400 Len=21 "MSG_5 ECHO" 37 2.165390 client server TCP 56150 > 6006 [ACK] Seq=221 Ack=148 Win=66632 Len=0 38 2.166314 client server TCP 56150 > 6006 [ACK] Seq=221 Ack=190 Win=66588 Len=0 39 2.364135 client server TCP 56150 > 6006 [ACK] Seq=221 Ack=211 Win=66568 Len=0 REDHAT: 17 2.081163 client server TCP 55879 > 6006 [PSH, ACK] Seq=111 Ack=106 Win=66672 Len=22 "MSG_1 RCV" 18 2.081178 server client TCP 6006 > 55879 [ACK] Seq=106 Ack=133 Win=5888 Len=0 19 2.081297 server client TCP 6006 > 55879 [PSH, ACK] Seq=106 Ack=133 Win=5888 Len=21 "MSG_1 ECHO" 20 2.081711 client server TCP 55879 > 6006 [PSH, ACK] Seq=133 Ack=106 Win=66672 Len=22 "MSG_2 RCV" 21 2.081761 client server TCP 55879 > 6006 [PSH, ACK] Seq=155 Ack=106 Win=66672 Len=22 "MSG_3 RCV" 22 2.081846 server client TCP 6006 > 55879 [PSH, ACK] Seq=127 Ack=177 Win=5888 Len=21 "MSG_2 ECHO" 23 2.081995 server client TCP 6006 > 55879 [PSH, ACK] Seq=148 Ack=177 Win=5888 Len=21 "MSG_3 ECHO" 24 2.082011 client server TCP 55879 > 6006 [PSH, ACK] Seq=177 Ack=106 Win=66672 Len=22 "MSG_4 RCV" 25 2.082362 client server TCP 55879 > 6006 [PSH, ACK] Seq=199 Ack=106 Win=66672 Len=22 "MSG_5 RCV" 26 2.082377 server client TCP 6006 > 55879 [ACK] Seq=169 Ack=221 Win=5888 Len=0 27 2.171003 client server TCP 55879 > 6006 [ACK] Seq=221 Ack=148 Win=66632 Len=0 28 2.171019 server client TCP 6006 > 55879 [PSH, ACK] Seq=169 Ack=221 Win=5888 Len=42 "MSG_4 ECHO + MSG_5 ECHO" 29 2.257498 client server TCP 55879 > 6006 [ACK] Seq=221 Ack=211 Win=66568 Len=0 so, I got confirmation things are not working correctly for RH: packet 28 is sent TOO LATE, it looks like the server is waiting for packet 27's ACK before doing anything. seems to me it's the most likely reason... then I realized that the "Win" parameters are different on Solaris & RH dumps: 50400 on Solaris, only 5888 on RH. that's another hint... I read the doc about the slide window & buffer window, and played around with the rcvBuffer & sendBuffer in java on my sockets, but never managed to change this 5888 value to anything else (I checked each time directly with tcpdump). does anybody know how to do this ? I'm having a hard time getting definitive information, as in some cases there's "auto-negotiation" that I might need to bypass, etc... I eventually managed to get only partially rid of my initial problem by setting the "tcp_slow_start_after_idle" parameter to 0 on RH, but it did not change the "win" parameter at all. the same problem was there for the first 4 groups of 5 messages, with TCP retransmission & TCP Dup ACK in tcpdump, then the problem disappeared altogether for all following groups of 5 messages. It doesn't seem like a very clean and/or generic solution to me. I'd really like to reproduce the exact same conditions under both OSes. I'll keep researching, but any help from TCP gurus would be greatly appreciated ! thanks !

    Read the article

  • Figuring out the Nyquist performance limitation of an ADC on an example PIC microcontroller

    - by AKE
    I'm spec-ing the suitability of a dsPIC microcontroller for an analog-to-digital application. This would be preferable to using dedicated A/D chips and a separate dedicated DSP chip. To do that, I've had to run through some computations, pulling the relevant parameters from the datasheets. I'm not sure I've got it right -- would appreciate a check! (EDITED NOTE: The PIC10F220 in the example below was selected ONLY to walk through a simple example to check that I'm interpreting Tacq, Fosc, TAD, and divisor correctly in working through this sort of Nyquist analysis. The actual chips I'm considering for the design are the dsPIC33FJ128MC804 (with 16b A/D) or dsPIC30F3014 (with 12b A/D).) A simple example: PIC10F220 is the simplest possible PIC with an ADC Runs at clock speed of 8MHz. Has an instruction cycle of 0.5us (4 clock steps per instruction) So: Taking Tacq = 6.06 us (acquisition time for ADC, assume chip temp. = 50*C) [datasheet p34] Taking Fosc = 8MHz (? clock speed) Taking divisor = 4 (4 clock steps per CPU instruction) This gives TAD = 0.5us (TAD = 1/(Fosc/divisor) ) Conversion time is 13*TAD [datasheet p31] This gives conversion time 6.5us ADC duration is then 12.56 us [? Tacq + 13*TAD] Assuming at least 2 instructions for load/store: This is another 1 us [0.5 us per instruction] Which would give max sampling rate of 73.7 ksps (1/13.56) Supposing 8 more instructions for real-time processing: This is another 4 us Thus, total ADC/handling time = 17.56us (12.56us + 1us + 4us) So expected upper sampling rate is 56.9 ksps. Nyquist frequency for this sampling rate is therefore 28 kHz. If this is right, it suggests the (theoretical) performance suitability of this chip's A/D is for signals that are bandlimited to 28 kHz. Is this a correct interpretation of the information given in the data sheet in obtaining the Nyquist performance limit? Any opinions on the noise susceptibility of ADCs in PIC / dsPIC chips would be much appreciated! AKE

    Read the article

  • Help with Java Program for Prime numbers

    - by Ben
    Hello everyone, I was wondering if you can help me with this program. I have been struggling with it for hours and have just trashed my code because the TA doesn't like how I executed it. I am completely hopeless and if anyone can help me out step by step, I would greatly appreciate it. In this project you will write a Java program that reads a positive integer n from standard input, then prints out the first n prime numbers. We say that an integer m is divisible by a non-zero integer d if there exists an integer k such that m = k d , i.e. if d divides evenly into m. Equivalently, m is divisible by d if the remainder of m upon (integer) division by d is zero. We would also express this by saying that d is a divisor of m. A positive integer p is called prime if its only positive divisors are 1 and p. The one exception to this rule is the number 1 itself, which is considered to be non-prime. A positive integer that is not prime is called composite. Euclid showed that there are infinitely many prime numbers. The prime and composite sequences begin as follows: Primes: 2, 3, 5, 7, 11, 13, 17, 19, 23, 29, … Composites: 1, 4, 6, 8, 9, 10, 12, 14, 15, 16, 18, 20, 21, 22, 24, 25, 26, 27, 28, … There are many ways to test a number for primality, but perhaps the simplest is to simply do trial divisions. Begin by dividing m by 2, and if it divides evenly, then m is not prime. Otherwise, divide by 3, then 4, then 5, etc. If at any point m is found to be divisible by a number d in the range 2 d m-1, then halt, and conclude that m is composite. Otherwise, conclude that m is prime. A moment’s thought shows that one need not do any trial divisions by numbers d which are themselves composite. For instance, if a trial division by 2 fails (i.e. has non-zero remainder, so m is odd), then a trial division by 4, 6, or 8, or any even number, must also fail. Thus to test a number m for primality, one need only do trial divisions by prime numbers less than m. Furthermore, it is not necessary to go all the way up to m-1. One need only do trial divisions of m by primes p in the range 2 p m . To see this, suppose m 1 is composite. Then there exist positive integers a and b such that 1 < a < m, 1 < b < m, and m = ab . But if both a m and b m , then ab m, contradicting that m = ab . Hence one of a or b must be less than or equal to m . To implement this process in java you will write a function called isPrime() with the following signature: static boolean isPrime(int m, int[] P) This function will return true or false according to whether m is prime or composite. The array argument P will contain a sufficient number of primes to do the testing. Specifically, at the time isPrime() is called, array P must contain (at least) all primes p in the range 2 p m . For instance, to test m = 53 for primality, one must do successive trial divisions by 2, 3, 5, and 7. We go no further since 11 53 . Thus a precondition for the function call isPrime(53, P) is that P[0] = 2 , P[1] = 3 , P[2] = 5, and P[3] = 7 . The return value in this case would be true since all these divisions fail. Similarly to test m =143 , one must do trial divisions by 2, 3, 5, 7, and 11 (since 13 143 ). The precondition for the function call isPrime(143, P) is therefore P[0] = 2 , P[1] = 3 , P[2] = 5, P[3] = 7 , and P[4] =11. The return value in this case would be false since 11 divides 143. Function isPrime() should contain a loop that steps through array P, doing trial divisions. This loop should terminate when 2 either a trial division succeeds, in which case false is returned, or until the next prime in P is greater than m , in which case true is returned. Function main() in this project will read the command line argument n, allocate an int array of length n, fill the array with primes, then print the contents of the array to stdout according to the format described below. In the context of function main(), we will refer to this array as Primes[]. Thus array Primes[] plays a dual role in this project. On the one hand, it is used to collect, store, and print the output data. On the other hand, it is passed to function isPrime() to test new integers for primality. Whenever isPrime() returns true, the newly discovered prime will be placed at the appropriate position in array Primes[]. This process works since, as explained above, the primes needed to test an integer m range only up to m , and all of these primes (and more) will already be stored in array Primes[] when m is tested. Of course it will be necessary to initialize Primes[0] = 2 manually, then proceed to test 3, 4, … for primality using function isPrime(). The following is an outline of the steps to be performed in function main(). • Check that the user supplied exactly one command line argument which can be interpreted as a positive integer n. If the command line argument is not a single positive integer, your program will print a usage message as specified in the examples below, then exit. • Allocate array Primes[] of length n and initialize Primes[0] = 2 . • Enter a loop which will discover subsequent primes and store them as Primes[1] , Primes[2], Primes[3] , ……, Primes[n -1] . This loop should contain an inner loop which walks through successive integers and tests them for primality by calling function isPrime() with appropriate arguments. • Print the contents of array Primes[] to stdout, 10 to a line separated by single spaces. In other words Primes[0] through Primes[9] will go on line 1, Primes[10] though Primes[19] will go on line 2, and so on. Note that if n is not a multiple of 10, then the last line of output will contain fewer than 10 primes. Your program, which will be called Prime.java, will produce output identical to that of the sample runs below. (As usual % signifies the unix prompt.) % java Prime Usage: java Prime [PositiveInteger] % java Prime xyz Usage: java Prime [PositiveInteger] % java Prime 10 20 Usage: java Prime [PositiveInteger] % java Prime 75 2 3 5 7 11 13 17 19 23 29 31 37 41 43 47 53 59 61 67 71 73 79 83 89 97 101 103 107 109 113 127 131 137 139 149 151 157 163 167 173 179 181 191 193 197 199 211 223 227 229 233 239 241 251 257 263 269 271 277 281 283 293 307 311 313 317 331 337 347 349 353 359 367 373 379 % 3 As you can see, inappropriate command line argument(s) generate a usage message which is similar to that of many unix commands. (Try doing the more command with no arguments to see such a message.) Your program will include a function called Usage() having signature static void Usage() that prints this message to stderr, then exits. Thus your program will contain three functions in all: main(), isPrime(), and Usage(). Each should be preceded by a comment block giving it’s name, a short description of it’s operation, and any necessary preconditions (such as those for isPrime().) See examples on the webpage.

    Read the article

  • Is it possible that a single-threaded program is executed simultaneously on more than one CPU core?

    - by Wolfgang Plaschg
    When I run a single-threaded program that i have written on my quad core Intel i can see in the Windows Task Manager that actually all four cores of my CPU are more or less active. One core is more active than the other three, but there is also activity on those. There's no other program (besided the OS kernel of course) running that would be plausible for that activitiy. And when I close my program all activity an all cores drops down to nearly zero. All is left is a little "noise" on the cores, so I'm pretty sure all the visible activity comes directly or indirectly (like invoking system routines) from my program. Is it possible that the OS or the cores themselves try to balance some code or execution on all four cores, even it's not a multithreaded program? Do you have any links that documents this technique? Some infos to the program: It's a console app written in Qt, the Task Manager states that only one thread is running. Maybe Qt uses threads, but I don't use signals or slots, nor any GUI. Link to Task Manager screenshot: http://img97.imageshack.us/img97/6403/taskmanager.png This question is language agnostic and not tied to Qt/C++, i just want to know if Windows or Intel do to balance also single-threaded code on all cores. If they do, how does this technique work? All I can think of is, that kernel routines like reading from disk etc. is scheduled on all cores, but this won't improve performance significantly since the code still has to run synchronous to the kernel api calls. EDIT Do you know any tools to do a better analysis of single and/or multi-threaded programs than the poor Windows Task Manager?

    Read the article

  • Calculating the total in JavaScript

    - by DAFFODIL
    OP, please replace this text with a detailed description of your problem. Your code is below. I used document.getElementById but the math is not working. I need total to be calculated: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml"> <head> <meta http-equiv="Content-Type" content="text/html; charset=iso-8859-1" /> <title></title> <script type = "text/javascript"> function a() { var q = document.getElementById('ad').value; document.getElementById('s').value=q + q; } </script> </head> <?php $con = mysql_connect("localhost","root",""); if (!$con) { die('Could not connect: ' . mysql_error()); } mysql_select_db("form1", $con); error_reporting(E_ALL ^ E_NOTICE); $nam=$_GET['msg']; $row=mysql_query("select * from inv where Name='$nam'"); while($row1=mysql_fetch_array($row)) { $Name=$row1['Name']; $Address =$row1['Address']; $City=$row1['City']; $Pincode=$row1['Pincode']; $No=$row1['No']; $Date=$row1['Date']; $DCNo=$row1['DCNo']; $DcDate=$row1['DcDate']; $YourOrderNo=$row1['YourOrderNo']; $OrderDate=$row1['OrderDate']; $VendorCode=$row1['VendorCode']; $SNo=$row1['SNo']; $descofgoods=$row1['descofgoods']; $Qty=$row1['Qty']; $Rate=$row1['Rate']; $Amount=$row1['Amount']; } ?> <body> <form id="form1" name="form1" method="post" action=""> <table width="846" border="0"> <tr> <td width="411" height="113">&nbsp;</td> <td width="412">&nbsp;</td> </tr> </table> <table width="846" border="0"> <tr> <td height="38">&nbsp;</td> </tr> </table> <table width="846" border="0"> <tr> <td width="390" rowspan="4">&nbsp;</td> <td width="92" height="35">&nbsp;</td> <td width="136"><?php echo $No;?></td> <td width="36">&nbsp;</td> <td width="170"><?php echo $Date;?></td> </tr> <tr> <td height="37">&nbsp;</td> <td><?php echo $DCNo;?></td> <td>&nbsp;</td> <td><?php echo $DcDate;?></td> </tr> <tr> <td height="34">&nbsp;</td> <td><?php echo $YourOrderNo;?></td> <td>&nbsp;</td> <td><?php echo $OrderDate;?></td> </tr> <tr> <td height="29">&nbsp;</td> <td><?php echo $VendorCode;?></td> <td>&nbsp;</td> <td>&nbsp;</td> </tr> </table> <table width="845" border="0"> <tr> <td height="38">&nbsp;</td> <td>&nbsp;</td> <td>&nbsp;</td> <td>&nbsp;</td> <td>&nbsp;</td> </tr> <tr> <td width="34">&nbsp;</td> <td width="457">&nbsp;</td> <td width="104">&nbsp;</td> <td width="79">&nbsp;</td> <td width="149">&nbsp;</td> </tr> <?php $i=1; $row=mysql_query("select * from inv where Name='$nam'"); while($row1=mysql_fetch_array($row)) { $descofgoods=$row1['descofgoods']; $Qty=$row1['Qty']; $Rate=$row1['Rate']; $Amount=$row1['Amount']; ?> <tr> <td><?php echo $i;?></td> <td><?php echo $descofgoods;?></td> <td><?php echo $Qty;?></td> <td><?php echo $Rate;?></td> <td><input name="Amount" type = "text" id ="ad" value="<?php echo $Amount;?>" /></td> </tr> <?php $i++;} ?> </table> <table width="844" border="0"> <tr> <td width="495" height="1065">&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; <input type="text" name="textfield2" /> &nbsp; &nbsp; &nbsp; &nbsp; </td> <td width="191">&nbsp;</td> <td width="144"><input type="text" name="tot" id="s" onclick="a()"; /></td> </tr>

    Read the article

  • Switch statement usage - C

    - by Jamie Keeling
    Hello, I have a thread function on Process B that contains a switch to perform certain operations based on the results of an event sent from Process A, these are stored as two elements in an array. I set the first element to the event which signals when Process A has data to send and I have the second element set to the event which indicates when Process A has closed. I have began to implement the functionality for the switch statement but I'm not getting the results as I expect. Consider the following: // //Thread function DWORD WINAPI ThreadFunc(LPVOID passedHandle) { for(i = 0; i < 2; i++) { ghEvents[i] = OpenEvent(EVENT_ALL_ACCESS, FALSE, TEXT("Global\\ProducerEvents")); if(ghEvents[i] == NULL) { getlasterror = GetLastError(); } } dwProducerEventResult = WaitForMultipleObjects( 2, ghEvents, FALSE, INFINITE); switch (dwProducerEventResult) { case WAIT_OBJECT_0 + 0: { //Producer sent data //unpackedHandle = *((HWND*)passedHandle); MessageBox(NULL,L"Test",L"Test",MB_OK); break; } case WAIT_OBJECT_0 + 1: { //Producer closed ExitProcess(1); break; } default: return; } } As you can see if the event in the first array is signalled Process B should display a simple message box, if the second array is signalled the application should close. When I actually close Process A, Process B displays the message box instead. If I leave the first case blank (Do nothing) both applications close as they should. Furthermore Process B sends data an error is thrown (When I comment out the unpacking): Have I implemented my switch statement incorrectly? I though I handled the unpacking of the HWND correctly too, any suggestions? Thanks for your time.

    Read the article

  • Using pipes in Linux with C

    - by Dave
    Hi, I'm doing a course in Operating Systems and we're supposed to learn how to use pipes to transfer data between processes. We were given this simple piece of code which demonstrates how to use pipes,but I'm having difficulty understanding it. #include <stdio.h> #include <stdlib.h> #include <unistd.h> main() { int pipefd [2], n; char buff[100] ; if( pipe( pipefd) < 0) { printf("can not create pipe \n"); } printf("read fd = %d, write fd = %d \n", pipefd[0], pipefd[1]); if ( write (pipefd[1],"hello world\n", 12)!= 12) { printf("pipe write error \n"); } if( ( n = read ( pipefd[0] , buff, sizeof ( buff) ) ) <= 0 ) { printf("pipe read error \n"); } write ( 1, buff, n ) ; exit (0); } What does the write function do? It seems to send data to the pipe and also print it to the screen (at least it seems like the second time the write function is called it does this). Does anyone have any suggestions of good websites for learning about topics such as this, FIFO, signals, other basic linux commands used in C?

    Read the article

  • XMLReader mysteriously fails when parsing document

    - by Valrus
    I have a php script that takes in some XML data and parses it, displaying various bits of information I pull out of it. This has been working fine for over 6 months, until recently it now fails mysteriously on a certain tag. The XML is generated from an outside source(a conferencing bridge), so I have no control over how it is built. I have put the xml through an online validator and it returned no errors. The code also works fine when I connect to another conferencing bridge and get the same output. I have been using XMLReader class so far and tried switching to SmipleXML, but it fails when I create the SimpleXML object using the data. Here is the snippet of where it fails while parsing: <CDR_SUMMARY> <FILE_VERSION>1001</FILE_VERSION> <NAME>Conference Title Hidden</NAME> <ID>10227</ID> <STATUS_STR>Auto_termination,_everybody_quit</STATUS_STR> <STATUS>4</STATUS> <GMT_OFFSET>-4</GMT_OFFSET> <START_TIME>2010-04-14T15:00:33</START_TIME> <DURATION> <HOUR>0</HOUR> <MINUTE>39</MINUTE> <SECOND>37</SECOND> </DURATION> <RESERVE_START_TIME>2010-04-14T15:00:33</RESERVE_START_TIME> <RESERVE_DURATION> <HOUR>12</HOUR> <MINUTE>0</MINUTE> <SECOND>0</SECOND> </RESERVE_DURATION> <MCU_FILE_NAME>c11</MCU_FILE_NAME> <FILE_SAVED>0</FILE_SAVED> <GMT_OFFSET_MINUTE>0</GMT_OFFSET_MINUTE> </CDR_SUMMARY> The <SOUND> opening tag is the last one read before failing. And this is my code: `public function processResponse($xml) { print "Processing List..."; $reader = new XMLReader($xml); try { $reader->setSchema("./schemas/response_trans_cdr_list.xsd"); } catch(Exception $e) { print "Exception:".$e->getMessage(); } //verify xml if($reader->xml($xml)) { while($reader->read()) { //$currentstring = $reader->readstring(); if($reader->name === "ACTION") { //into meat of resposnse while($reader->read()) { //print "Looping..."; //$currentstring = $reader->readInnerXML(); //print $currentstring; if($reader->nodeType == XMLReader::ELEMENT) { if($reader->name === "ID") { $this->conferenceIDs[$this->counter] = $reader->readString(); print "<BR>Conf ID found: ".$this->counter." ID: ".$this->conferenceIDs[$this->counter]; $this->counter += 1; } else if($reader->name === "START_TIME") { //conference start time. print "<BR>Start Time Found! "; $this->conferenceStarts[$this->counter-1] = $reader->readString(); } else if($reader->name === "NAME") { print "<BR> Name Found!"; $this->conferenceNames[$this->counter] = $reader->readString(); } else if($reader->name === "MCU_FILE_NAME") { print "<BR> MCU_FILE_NAME Found!"; //print $this->counter." File Name: ".$reader->readstring()."<BR>"; } else if($reader->name === "RESERVE_START_TIME") { print "<BR> RESERVE_START_TIME Found!"; } else if($reader->name === "FILE_VERSION") { print "<BR> FILE_VERSION Found!"; } else if($reader->name === "STATUS_STR") { print "<BR> STATUS_STR Found!"; } else if($reader->name === "STATUS") { print "<BR> STATUS Found!"; } else if($reader->name === "GMT_OFFSET") { print "<BR> GMT_OFFSET Found!"; } else if($reader->name === "DURATION") { print "<BR> DURATION Found!"; } else if($reader->name === "RESERVE_START_TIME") { print "<BR> RESERVE_START_TIME Found!"; } else if($reader->name === "RESERVE_DURATION") { print "<BR> RESERVE_DURATION Found!"; } else if($reader->name === "FILE_SAVED") { print "<BR> FILE_SAVED Found!"; } else if($reader->name === "GMT_OFFSET_MINUTE") { print "<BR> GMT_OFFSET_MINUTE Found!"; } else if($reader->name === "HOUR") { print "<BR> HOUR Found!"; } else if($reader->name === "MINUTE") { print "<BR> MINUTE Found!"; } else if($reader->name === "SECOND") { print "<BR> SECOND Found!"; } }else if($reader->nodeType == XMLReader::END_ELEMENT) { print "Close Element".$reader->name; } } print "End Action Loop"; } } } else { print "Error reading response: Bad XML returned"; } }` Anyone have any ideas what could be causing this failure? the code exits gracefully and I see the "End Action Loop" message in my output. It's like it just spontaneously exits the loop.

    Read the article

  • Django - how to write users and profiles handling in best way?

    - by SpankMe
    Hey, I am writing simple site that requires users and profiles to be handled. The first initial thought is to use django's build in user handling, but then the user model is too narrow and does not contain fields that I need. The documentation mentions user profiles, but user profiles section has been removed from djangobook covering django 1.0 (ideally, the solution should work with django 1.2), and the Internet is full of different solutions, not making the choice easier (like user model inheritance, user profiles and django signals, and so on). I would like to know, how to write this in good, modern, fast and secure way. Should I try to extend django builtin user model, or maybe should I create my own user model wide enough to keep all the information I need? Below you may find some specifications and expectations from the working solution: users should be able to register and authenticate every user should have profile (or model with all required fields) users dont need django builtin admin panel, but they need to edit their profiles/models via simple web form Please, let me know how do you solve those issues in your applications, and what is the best current way to handle users with django. Any links to articles/blogs or code examples are highly appreciated!

    Read the article

  • Programmatically disable WiredHeadset

    - by tyrone-tudehope
    Hi, I have an HTC Hero with a major issue. It thinks that the headset/headphones are plugged in. I sent it to HTC and they said there is water damage so no fix. I have tried toggleheadset, toggleheadset2. I've rooted my device and installed the Android 2.1 ROM. Now I found out that AudioManager.setRouting and .setWiredHeadsetOn(bool) have been deprecated and subsequently removed. I read a post somewhere about how you can create a wrapper for the AudioSystem class as the setRouting is still available there. I as of yet have not been able to figure out how to go about doing this as the AudioSystem class is hidden in the SDK and the code makes use of native functions. Does anybody know of a way to go about creating and implementing a wrapper for AudioSystem or of another way to disable the headset? P.S. I've cleaned out the headset port so there is no dust or anything sending false signals to the mainboard. Any help will be greatly appreciated. Thanks, Tyrone

    Read the article

  • How to get at contents of placeholder::_1

    - by sheepsimulator
    I currently have the following code: using boost::bind; typedef boost::signal<void(EventDataItem&)> EventDataItemSignal; class EventDataItem { ... EventDataItemSignal OnTrigger; ... } typedef std::list< shared_ptr<EventDataItem> > DataItemList; typedef std::list<boost::signals::connection> ConnectionList; class MyClass { void OnStart() { DataItemList dilItems; ConnectionList clConns; DataItemList::iterator iterDataItems; for(iterDataItems = dilItems.begin(); iterDataItems != dilItems.end(); iterDataItems++) { // Create Connections from Triggers clConns.push_back((*iterDataItems)->OnTrigger.connect( bind(&MyClass::OnEventTrigger, this))); } } void OnEventTrigger() { // ... Do stuff on Trigger... } } I'd like to change MyClass::OnStart to use std::transform to achieve the same thing: void MyClass::OnStart() { DataItemList dilItems; ConnectionList clConns; // Resize connection list to match number of data items clConns.resize(dilItems.size()); // Build connection list from Items // note: errors on the placeholder _1->OnTrigger std::transform(dilItems.begin(), dilItems.end(), clConns.begin(), bind(&EventDataItemSignal::connect, _1->OnTrigger, bind(&MyClass::Stuff, this))); } However, my hiccup is _1-OnTrigger. How can I reference OnTrigger from placeholder _1?

    Read the article

  • SOLVED: Lisp: macro calling a function works in interpreter, fails in compiler (SBCL + CMUCL)

    - by ttsiodras
    As suggested in a macro-related question I recently posted to SO, I coded a macro called "fast" via a call to a function (here is the standalone code in pastebin): (defun main () (progn (format t "~A~%" (+ 1 2 (* 3 4) (+ 5 (- 8 6)))) (format t "~A~%" (fast (+ 1 2 (* 3 4) (+ 5 (- 8 6))))))) This works in the REPL, under both SBCL and CMUCL: $ sbcl This is SBCL 1.0.52, an implementation of ANSI Common Lisp. ... * (load "bug.cl") 22 22 $ Unfortunately, however, the code no longer compiles: $ sbcl This is SBCL 1.0.52, an implementation of ANSI Common Lisp. ... * (compile-file "bug.cl") ... ; during macroexpansion of (FAST (+ 1 2 ...)). Use *BREAK-ON-SIGNALS* to ; intercept: ; ; The function COMMON-LISP-USER::CLONE is undefined. So it seems that by having my macro "fast" call functions ("clone","operation-p") at compile-time, I trigger issues in Lisp compilers (verified in both CMUCL and SBCL). Any ideas on what I am doing wrong and/or how to fix this?

    Read the article

  • How to compare two variables from a java class in jess and execute a rule?

    - by user3417084
    I'm beginner in Jess. I'm trying to compare two variables from a Java class in Jess and trying to execute a rule. I have imported cTNumber and measuredCurrent (both are integer)form a java class called CurrentSignal. Similarly imported vTNumberand measuredVoltage form a java class DERSignal. Now I want to make a rule such that if cTNumber is equal to vTNumber then multiply measuredCurrent and measuredVoltage (Both are double) for calculating power. I'm trying in this way.... (import signals.*) (deftemplate CurrentSignal (declare (from-class CurrentSignal))) (deftemplate DERSignal (declare (from-class DERSignal))) (defglobal ?*CTnumber* = 0) (defglobal ?*VTnumber* = 0) (defglobal ?*VTnumberDER* = 0) (defglobal ?*measuredCurrent* = 0) (defglobal ?*measuredVoltage* = 0) (defglobal ?*measuredVoltageDER* = 0) (defrule Get-CT-Number (CurrentSignal (cTNumber ?m)) (CurrentSignal (measuredCurrent ?c)) => (bind ?*measuredCurrent* ?c) (printout t "Measured Current : " ?*measuredCurrent*" Amps"crlf) (bind ?*CTnumber* ?m) (printout t ?*CTnumber* crlf) ) (defrule Get-DER-Number (DERSignal (vTNumber ?o)) (DERSignal (measuredVoltage ?V)) => (bind ?*measuredVoltageDER* ?V) (printout t "Measured Voltage : " ?*measuredVoltageDER* " V" crlf) (bind ?*VTnumberDER* ?o) (printout t ?*VTnumberDER* crlf) ) (defrule Power-Calculation-DER-signal "Power calculation of DER Bay" (test (= ?*CTnumber* ?*VTnumberDER* )) => (printout t "Total Generation : " (* ?*measuredCurrent* ?*measuredVoltageDER*) crlf) ) But the Total Generation is showing 0. But I tried calculating in Java and it's showing a number. Can anyone please help me to solve this problem. Thank you.

    Read the article

  • Memory limit for running external executables within Asp.net

    - by itsbalur
    I am using WkhtmltoPdf in my C# web application running in .NET 4.0 to generate PDFs from HTML files. In general everything works fine except when the size of the HTML file is below 250KB. Once the HTML file size increases beyond that, the process which runs the wkhtmltopdf.exe gives an exception as below. On the Task Manager, I have seen that the Memory value for the wkhtmltopdf.exe process does not increase beyond a value of 40,096 K, which I believe is the reason why the process is abandoned in between. How can we configure such that the memory limit for external exes can be increased? Is there any other way of solving this issue? More info: When I run the conversion from the command line directly, the PDF is generated fine. So, its unlikely to be a problem with WkhtmlToPdf. The error is from localhost. I have tried the same on the DEV server, with the same result. Exception: > [Exception: Loading pages (1/6) [> > ] 0% [======> ] > 10% [======> ] 11% > [=======> ] 13% > [=========> ] 15% > [==========> ] 18% > [============> ] 20% > [=============> ] 22% > [==============> ] 24% > [===============> ] 26% > [=================> ] 29% > [==================> ] 31% > [===================> ] 33% > [=====================> ] 35% > [======================> ] 37% > [========================> ] 40% > [=========================> ] 42% > [==========================> ] 44% > [============================> ] 47% > [=============================> ] 49% > [==============================> ] 51% > [============================================================] 100% > Counting pages (2/6) > [============================================================] Object > 1 of 1 Resolving links (4/6) > [============================================================] Object > 1 of 1 Loading headers and footers (5/6) > Printing pages (6/6) [> > ] Preparing [=> > ] Page 1 of 49 [==> > ] Page 2 of 49 [===> > ] Page 3 of 49 [====> > ] Page 4 of 49 [======> > ] Page 5 of 49 [=======> > ] Page 6 of 49 [========> > ] Page 7 of 49 [=========> > ] Page 8 of 49 [==========> > ] Page 9 of 49 [============> > ] Page 10 of 49 [=============> > ] Page 11 of 49 [==============> > ] Page 12 of 49 [===============> > ] Page 13 of 49 [================> > ] Page 14 of 49 [==================> > ] Page 15 of 49 [===================> > ] Page 16 of 49 [====================> > ] Page 17 of 49 [=====================> > ] Page 18 of 49 [======================> > ] Page 19 of 49 [========================> > ] Page 20 of 49 [=========================> > ] Page 21 of 49 [==========================> > ] Page 22 of 49 [===========================> > ] Page 23 of 49 [============================> > ] Page 24 of 49 [==============================> > ] Page 25 of 49 [===============================> > ] Page 26 of 49 [=================================> > ] Page 27 of 49 [==================================> > ] Code that I use: var fileName = " - "; var wkhtmlDir = ConfigurationManager.AppSettings[Constants.AppSettings.ExportToPdfExecutablePath]; var wkhtml = ConfigurationManager.AppSettings[Constants.AppSettings.ExportToPdfExecutablePath] + "\\wkhtmltopdf.exe"; var p = new Process(); string switches = ""; switches += "--print-media-type "; switches += "--margin-top 10mm --margin-bottom 10mm --margin-right 5mm --margin-left 5mm "; switches += "--page-size A4 "; switches += "--disable-smart-shrinking "; var startInfo = new ProcessStartInfo { CreateNoWindow = true, FileName = wkhtml, Arguments = switches + " " + url + " " + fileName, UseShellExecute = false, RedirectStandardOutput = true, RedirectStandardError = true, RedirectStandardInput=true, WorkingDirectory=wkhtmlDir }; p.StartInfo = startInfo; p.Start();

    Read the article

  • Probelm with String.split() in java

    - by Matt
    What I am trying to do is read a .java file, and pick out all of the identifiers and store them in a list. My problem is with the .split() method. If you run this code the way it is, you will get ArrayOutOfBounds, but if you change the delimiter from "." to anything else, the code works. But I need to lines parsed by "." so is there another way I could accomplish this? import java.io.BufferedReader; import java.io.FileNotFoundException; import java.io.FileReader; import java.io.IOException; import java.util.*; public class MyHash { private static String[] reserved = new String[100]; private static List list = new LinkedList(); private static List list2 = new LinkedList(); public static void main (String args[]){ Hashtable hashtable = new Hashtable(997); makeReserved(); readFile(); String line; ListIterator itr = list.listIterator(); int listIndex = 0; while (listIndex < list.size()) { if (itr.hasNext()){ line = itr.next().toString(); //PROBLEM IS HERE!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! String[] words = line.split("."); //CHANGE THIS AND IT WILL WORK System.out.println(words[0]); //TESTING TO SEE IF IT WORKED } listIndex++; } } public static void readFile() { String text; String[] words; BufferedReader in = null; try { in = new BufferedReader(new FileReader("MyHash.java")); //NAME OF INPUT FILE } catch (FileNotFoundException ex) { Logger.getLogger(MyHash.class.getName()).log(Level.SEVERE, null, ex); } try { while ((text = in.readLine()) != null){ text = text.trim(); words = text.split("\\s+"); for (int i = 0; i < words.length; i++){ list.add(words[i]); } for (int j = 0; j < reserved.length; j++){ if (list.contains(reserved[j])){ list.remove(reserved[j]); } } } } catch (IOException ex) { Logger.getLogger(MyHash.class.getName()).log(Level.SEVERE, null, ex); } try { in.close(); } catch (IOException ex) { Logger.getLogger(MyHash.class.getName()).log(Level.SEVERE, null, ex); } } public static int keyIt (int x) { int key = x % 997; return key; } public static int horner (String word){ int length = word.length(); char[] letters = new char[length]; for (int i = 0; i < length; i++){ letters[i]=word.charAt(i); } char[] alphabet = new char[26]; String abc = "abcdefghijklmnopqrstuvwxyz"; for (int i = 0; i < 26; i++){ alphabet[i]=abc.charAt(i); } int[] numbers = new int[length]; int place = 0; for (int i = 0; i < length; i++){ for (int j = 0; j < 26; j++){ if (alphabet[j]==letters[i]){ numbers[place]=j+1; place++; } } } int hornered = numbers[0] * 32; for (int i = 1; i < numbers.length; i++){ hornered += numbers[i]; if (i == numbers.length -1){ return hornered; } hornered = hornered % 997; hornered *= 32; } return hornered; } public static String[] makeReserved (){ reserved[0] = "abstract"; reserved[1] = "assert"; reserved[2] = "boolean"; reserved[3] = "break"; reserved[4] = "byte"; reserved[5] = "case"; reserved[6] = "catch"; reserved[7] = "char"; reserved[8] = "class"; reserved[9] = "const"; reserved[10] = "continue"; reserved[11] = "default"; reserved[12] = "do"; reserved[13] = "double"; reserved[14] = "else"; reserved[15] = "enum"; reserved[16] = "extends"; reserved[17] = "false"; reserved[18] = "final"; reserved[19] = "finally"; reserved[20] = "float"; reserved[21] = "for"; reserved[22] = "goto"; reserved[23] = "if"; reserved[24] = "implements"; reserved[25] = "import"; reserved[26] = "instanceof"; reserved[27] = "int"; reserved[28] = "interface"; reserved[29] = "long"; reserved[30] = "native"; reserved[31] = "new"; reserved[32] = "null"; reserved[33] = "package"; reserved[34] = "private"; reserved[35] = "protected"; reserved[36] = "public"; reserved[37] = "return"; reserved[38] = "short"; reserved[39] = "static"; reserved[40] = "strictfp"; reserved[41] = "super"; reserved[42] = "switch"; reserved[43] = "synchronize"; reserved[44] = "this"; reserved[45] = "throw"; reserved[46] = "throws"; reserved[47] = "trasient"; reserved[48] = "true"; reserved[49] = "try"; reserved[50] = "void"; reserved[51] = "volatile"; reserved[52] = "while"; reserved[53] = "="; reserved[54] = "=="; reserved[55] = "!="; reserved[56] = "+"; reserved[57] = "-"; reserved[58] = "*"; reserved[59] = "/"; reserved[60] = "{"; reserved[61] = "}"; return reserved; } }

    Read the article

  • How to interrupt a thread performing a blocking socket connect?

    - by Jason R
    I have some code that spawns a pthread that attempts to maintain a socket connection to a remote host. If the connection is ever lost, it attempts to reconnect using a blocking connect() call on its socket. Since the code runs in a separate thread, I don't really care about the fact that it uses the synchronous socket API. That is, until it comes time for my application to exit. I would like to perform some semblance of an orderly shutdown, so I use thread synchronization primitives to wake up the thread and signal for it to exit, then perform a pthread_join() on the thread to wait for it to complete. This works great, unless the thread is in the middle of a connect() call when I command the shutdown. In that case, I have to wait for the connect to time out, which could be a long time. This makes the application appear to take a long time to shut down. What I would like to do is to interrupt the call to connect() in some way. After the call returns, the thread will notice my exit signal and shut down cleanly. Since connect() is a system call, I thought that I might be able to intentionally interrupt it using a signal (thus making the call return EINTR), but I'm not sure if this is a robust method in a POSIX threads environment. Does anyone have any recommendations on how to do this, either using signals or via some other method? As a note, the connect() call is down in some library code that I cannot modify, so changing to a non-blocking socket is not an option.

    Read the article

  • segmentation fault using BaseCode encryption

    - by Natasha Thapa
    i took the code from the links below to encrypt and decrypt a text but i get segmentation fault when trying to run this any ideas?? http://etutorials.org/Programming/secure+programming/Chapter+4.+Symmetric+Cryptography+Fundamentals/4.5+Performing+Base64+Encoding/ http://etutorials.org/Programming/secure+programming/Chapter+4.+Symmetric+Cryptography+Fundamentals/4.6+Performing+Base64+Decoding/ #include <stdlib.h> #include <string.h> #include <stdio.h> static char b64revtb[256] = { -3, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, /*0-15*/ -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, /*16-31*/ -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, 62, -1, -1, -1, 63, /*32-47*/ 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, -1, -1, -1, -2, -1, -1, /*48-63*/ -1, 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, /*64-79*/ 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, -1, -1, -1, -1, -1, /*80-95*/ -1, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, /*96-111*/ 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, -1, -1, -1, -1, -1, /*112-127*/ -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, /*128-143*/ -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, /*144-159*/ -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, /*160-175*/ -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, /*176-191*/ -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, /*192-207*/ -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, /*208-223*/ -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, /*224-239*/ -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 /*240-255*/ }; unsigned char *spc_base64_encode( unsigned char *input , size_t len , int wrap ) ; unsigned char *spc_base64_decode(unsigned char *buf, size_t *len, int strict, int *err); static unsigned int raw_base64_decode(unsigned char *in, unsigned char *out, int strict, int *err); unsigned char *tmbuf = NULL; static char tmpbuffer[] ={0}; int main(void) { memset( tmpbuffer, NULL, sizeof( tmpbuffer ) ); sprintf( tmpbuffer, "%s:%s" , "username", "password" ); tmbuf = spc_base64_encode( (unsigned char *)tmpbuffer , strlen( tmpbuffer ), 0 ); printf(" The text %s has been encrytped to %s \n", tmpbuffer, tmbuf ); unsigned char *decrypt = NULL; int strict; int *err; decrypt = spc_base64_decode( tmbuf , strlen( tmbuf ), 0, err ); printf(" The text %s has been decrytped to %s \n", tmbuf , decrypt); } static char b64table[64] = "ABCDEFGHIJKLMNOPQRSTUVWXYZ" "abcdefghijklmnopqrstuvwxyz" "0123456789+/"; /* Accepts a binary buffer with an associated size. * Returns a base64 encoded, NULL-terminated string. */ unsigned char *spc_base64_encode(unsigned char *input, size_t len, int wrap) { unsigned char *output, *p; size_t i = 0, mod = len % 3, toalloc; toalloc = (len / 3) * 4 + (3 - mod) % 3 + 1; if (wrap) { toalloc += len / 57; if (len % 57) toalloc++; } p = output = (unsigned char *)malloc(((len / 3) + (mod ? 1 : 0)) * 4 + 1); if (!p) return 0; while (i < len - mod) { *p++ = b64table[input[i++] >> 2]; *p++ = b64table[((input[i - 1] << 4) | (input[i] >> 4)) & 0x3f]; *p++ = b64table[((input[i] << 2) | (input[i + 1] >> 6)) & 0x3f]; *p++ = b64table[input[i + 1] & 0x3f]; i += 2; if (wrap && !(i % 57)) *p++ = '\n'; } if (!mod) { if (wrap && i % 57) *p++ = '\n'; *p = 0; return output; } else { *p++ = b64table[input[i++] >> 2]; *p++ = b64table[((input[i - 1] << 4) | (input[i] >> 4)) & 0x3f]; if (mod = = 1) { *p++ = '='; *p++ = '='; if (wrap) *p++ = '\n'; *p = 0; return output; } else { *p++ = b64table[(input[i] << 2) & 0x3f]; *p++ = '='; if (wrap) *p++ = '\n'; *p = 0; return output; } } } static unsigned int raw_base64_decode(unsigned char *in, unsigned char *out, int strict, int *err) { unsigned int result = 0, x; unsigned char buf[3], *p = in, pad = 0; *err = 0; while (!pad) { switch ((x = b64revtb[*p++])) { case -3: /* NULL TERMINATOR */ if (((p - 1) - in) % 4) *err = 1; return result; case -2: /* PADDING CHARACTER. INVALID HERE */ if (((p - 1) - in) % 4 < 2) { *err = 1; return result; } else if (((p - 1) - in) % 4 == 2) { /* Make sure there's appropriate padding */ if (*p != '=') { *err = 1; return result; } buf[2] = 0; pad = 2; result++; break; } else { pad = 1; result += 2; break; } case -1: if (strict) { *err = 2; return result; } break; default: switch (((p - 1) - in) % 4) { case 0: buf[0] = x << 2; break; case 1: buf[0] |= (x >> 4); buf[1] = x << 4; break; case 2: buf[1] |= (x >> 2); buf[2] = x << 6; break; case 3: buf[2] |= x; result += 3; for (x = 0; x < 3 - pad; x++) *out++ = buf[x]; break; } break; } } for (x = 0; x < 3 - pad; x++) *out++ = buf[x]; return result; } /* If err is non-zero on exit, then there was an incorrect padding error. We * allocate enough space for all circumstances, but when there is padding, or * there are characters outside the character set in the string (which we are * supposed to ignore), then we end up allocating too much space. You can * realloc() to the correct length if you wish. */ unsigned char *spc_base64_decode(unsigned char *buf, size_t *len, int strict, int *err) { unsigned char *outbuf; outbuf = (unsigned char *)malloc(3 * (strlen(buf) / 4 + 1)); if (!outbuf) { *err = -3; *len = 0; return 0; } *len = raw_base64_decode(buf, outbuf, strict, err); if (*err) { free(outbuf); *len = 0; outbuf = 0; } return outbuf; }

    Read the article

  • spring annotation configuration issue

    - by shrimpy
    I don't know why spring 2.5.6 keeps complaining, but I don't have any "orderBy" annotation. 2009-10-10 13:55:37.242::WARN: Nested in org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'org.springframework.context.annotation.internalPersiste nceAnnotationProcessor': Error setting property values; nested exception is org.springframework.beans.NotWritablePropertyException: Invalid property 'order' of bean class [org.springfra mework.orm.jpa.support.PersistenceAnnotationBeanPostProcessor]: Bean property 'order' is not writable or has an invalid setter method. Does the parameter type of the setter match the re turn type of the getter?: org.springframework.beans.NotWritablePropertyException: Invalid property 'order' of bean class [org.springframework.orm.jpa.support.PersistenceAnnotationBeanPostProcessor]: Bean propert y 'order' is not writable or has an invalid setter method. Does the parameter type of the setter match the return type of the getter? at org.springframework.beans.BeanWrapperImpl.setPropertyValue(BeanWrapperImpl.java:801) at org.springframework.beans.BeanWrapperImpl.setPropertyValue(BeanWrapperImpl.java:651) at org.springframework.beans.AbstractPropertyAccessor.setPropertyValues(AbstractPropertyAccessor.java:78) at org.springframework.beans.AbstractPropertyAccessor.setPropertyValues(AbstractPropertyAccessor.java:59) at org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.applyPropertyValues(AbstractAutowireCapableBeanFactory.java:1276) at org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.populateBean(AbstractAutowireCapableBeanFactory.java:1010) or even when I swap to use lower version spring 2.5.1, it's still complaining: 2009-10-10 13:57:56.062::WARN: failed ContextHandlerCollection@5da0b94d java.lang.NoClassDefFoundError: org/springframework/context/support/AbstractRefreshableConfigApplicationContext at java.lang.ClassLoader.defineClass1(Native Method) at java.lang.ClassLoader.defineClass(ClassLoader.java:621) at java.security.SecureClassLoader.defineClass(SecureClassLoader.java:124) at java.net.URLClassLoader.defineClass(URLClassLoader.java:260) at java.net.URLClassLoader.access$000(URLClassLoader.java:56) at java.net.URLClassLoader$1.run(URLClassLoader.java:195) at java.security.AccessController.doPrivileged(Native Method) at java.net.URLClassLoader.findClass(URLClassLoader.java:188) at org.mortbay.jetty.webapp.WebAppClassLoader.loadClass(WebAppClassLoader.java:366) at org.mortbay.jetty.webapp.WebAppClassLoader.loadClass(WebAppClassLoader.java:337) at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:320) at java.lang.ClassLoader.defineClass1(Native Method) at java.lang.ClassLoader.defineClass(ClassLoader.java:621) at java.security.SecureClassLoader.defineClass(SecureClassLoader.java:124) at java.net.URLClassLoader.defineClass(URLClassLoader.java:260) at java.net.URLClassLoader.access$000(URLClassLoader.java:56) at java.net.URLClassLoader$1.run(URLClassLoader.java:195) at java.security.AccessController.doPrivileged(Native Method) at java.net.URLClassLoader.findClass(URLClassLoader.java:188) at org.mortbay.jetty.webapp.WebAppClassLoader.loadClass(WebAppClassLoader.java:366) at org.mortbay.jetty.webapp.WebAppClassLoader.loadClass(WebAppClassLoader.java:337) at org.springframework.util.ClassUtils.forName(ClassUtils.java:230) at org.springframework.util.ClassUtils.forName(ClassUtils.java:183) at org.springframework.web.context.ContextLoader.determineContextClass(ContextLoader.java:283) at org.springframework.web.context.ContextLoader.createWebApplicationContext(ContextLoader.java:243) If I do not use annotation, it works fine. No problem at all, Everything happened after this <beans xmlns="http://www.springframework.org/schema/beans" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:context="http://www.springframework.org/schema/context" xsi:schemaLocation="http://www.springframework.org/schema/beans http://www.springframework.org/schema/beans/spring-beans-2.5.xsd http://www.springframework.org/schema/context http://www.springframework.org/schema/context/spring-context-2.5.xsd" default-autowire="byName"> <context:component-scan base-package="demo.dao"> <context:include-filter type="annotation" expression="org.springframework.stereotype.Repository"/> </context:component-scan> </beans> and I am sure my spring is configured properly. <?xml version="1.0" encoding="UTF-8"?> <beans xmlns="http://www.springframework.org/schema/beans" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:aop="http://www.springframework.org/schema/aop" xmlns:util="http://www.springframework.org/schema/util" xmlns:context="http://www.springframework.org/schema/context" xmlns:tx="http://www.springframework.org/schema/tx" xsi:schemaLocation="http://www.springframework.org/schema/beans http://www.springframework.org/schema/beans/spring-beans-2.5.xsd http://www.springframework.org/schema/aop http://www.springframework.org/schema/aop/spring-aop-2.5.xsd http://www.springframework.org/schema/util http://www.springframework.org/schema/util/spring-util-2.5.xsd http://www.springframework.org/schema/context http://www.springframework.org/schema/context/spring-context-2.5.xsd http://www.springframework.org/schema/tx http://www.springframework.org/schema/tx/spring-tx-2.5.xsd" default-autowire="byName"> <!-- For mail settings and future properties files --> <bean id="propertyConfigurer" class="org.springframework.beans.factory.config.PropertyPlaceholderConfigurer"> <property name="locations"> <list> <value>classpath:jdbc.properties</value> </list> </property> </bean> <!-- Check all the beans managed by Spring for persistence-related annotations. e.g. PersistenceContext --> <bean class="org.springframework.orm.jpa.support.PersistenceAnnotationBeanPostProcessor" /> <bean id="dataSource" class="org.springframework.jdbc.datasource.DriverManagerDataSource"> <property name="driverClassName" value="${jdbc.driverClassName}"/> <property name="url" value="${jdbc.url}"/> <property name="username" value="${jdbc.username}"/> <property name="password" value="${jdbc.password}"/> </bean> <bean id="entityManagerFactory" class="org.springframework.orm.jpa.LocalContainerEntityManagerFactoryBean"> <property name="dataSource" ref="dataSource"/> <!-- jpaVendorAdapter Hibernate, injected into emf --> <property name="jpaVendorAdapter"> <bean class="org.springframework.orm.jpa.vendor.HibernateJpaVendorAdapter"> <property name="showSql" value="${hibernate.show_sql}"/> <!-- Data Definition Language script is generated and executed for each run --> <property name="generateDdl" value="${jdbc.generateDdl}"/> </bean> </property> <!--<property name="hibernateProperties"> --> <property name="jpaProperties"> <props> <prop key="hibernate.dialect">${hibernate.dialect} </prop> <prop key="hibernate.show_sql">${hibernate.show_sql}</prop> <prop key="hibernate.hbm2ddl.auto">${hibernate.hbm2ddl.auto} </prop> </props> </property> </bean> <tx:annotation-driven transaction-manager="transactionManager" /> <bean id="transactionManager" class="org.springframework.orm.jpa.JpaTransactionManager"> <property name="entityManagerFactory" ref="entityManagerFactory"/> <property name="dataSource" ref="dataSource"/> </bean> </beans> Can anyone tell me what is wrong? How can I fix this?

    Read the article

  • Help with java GUI- has error in main thread

    - by jan
    Hello guys, Basically im trying to do a Insurance Application form in java. And it uses multiple JPanels in a JFrame. -adding of JPanel into main program frame was done like this: //jpCenterArea to hold jp1-jp7 jpCenterArea.add(jp1); jpCenterArea.add(jp2); jpCenterArea.add(jp3); jpCenterArea.add(jp4); ...etc ********Add Jpanels to JFrame*****/ add(jpTitle, BorderLayout.NORTH); add(jpCenterArea, BorderLayout.CENTER); add(jpBottom, BorderLayout.SOUTH); However, even though program can compile, it cannot be run. error as mentioned below: Exception in thread "main" java.lang.NullPointerException at java.awt.Container.addImpl<Container.java:1045> at java.awt.Container.add<Container.java:365> at TravelInsuranceApplication.<init>TravelInsuranceApplication.java:120> at TravelInsuranceApplication.main<TravelInsuranceApplication.java:154> 1 import javax.swing.*; 2 import java.awt.*; 3 public class TravelInsuranceApplication extends JFrame 4 { 5 //declare private variables 6 private JLabel jlblTitle, jlblName, jlblNRIC, jlblAdd, jlblPostal, jlblContact, jlblDOB, 7 jlblEmail, jlblPeriod; 8 private JLabel jlblDeparture, jlblDays, jlblZone, jlblPlan; 9 private JTextField jtfName, jtfIC, jtfAdd, jtfPostal, jtfContact, jtfEmail, jtfZone; 10 private JRadioButton jrbResident, jrbOffice, jrbDeluxe, jrbClassic, jrbAsia, jrbWorldwide; 11 private ButtonGroup bgContact, bgZone, bgPlan; 12 private JComboBox jcDay, jcMonth, jcYear; 13 private JButton jbtnSubmit, jbtnCalculate, jbtnClear; 14 private JPanel jpTitle,jp1, jp2, jp3, jp4, jp5, jp6, jp7, jpBottom, jpCenterArea; 15 String[] day = {"1", "2", "3"}; 16 String[] month = {"january", "february"}; 17 String[] year = {"1981", "1985", "1990", "1995"}; 18 19 //constructor and GUI development 20 public TravelInsuranceApplication() 21 { 22 setSize(500,200); 23 setTitle("Travel Insurance Application"); 24 setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE); 25 setLayout(new BorderLayout()); 26 27 //create ALL component objects/ 28 jlblTitle = new JLabel("Travel Insurance Application: "); 29 jlblName = new JLabel("Name of Insured: "); 30 jlblNRIC = new JLabel("NRIC: "); 31 jlblAdd = new JLabel("Address: "); 32 jlblPostal = new JLabel("Postal Code: "); 33 jlblContact = new JLabel("Telephone: "); 34 jlblDOB = new JLabel("Date Of Birth: "); 35 jlblEmail = new JLabel("Email Address: "); 36 jlblPeriod = new JLabel("Period Of Insurance "); 37 jlblDeparture = new JLabel("Departure Date "); 38 jlblDays = new JLabel("How Many Days To Insure "); 39 jlblZone = new JLabel("Zone: "); 40 jlblPlan = new JLabel("Plan: "); 41 42 jtfName = new JTextField(50); 43 jtfIC = new JTextField(15); 44 jtfAdd = new JTextField(50); 45 jtfPostal = new JTextField(15); 46 jtfContact = new JTextField(15); 47 jtfEmail = new JTextField(50); 48 jtfZone = new JTextField(100); 49 50 jrbResident = new JRadioButton("Rseident/Pgr"); 51 jrbOffice = new JRadioButton("Office/HP"); 52 jrbAsia = new JRadioButton("Asia"); 53 jrbAsia = new JRadioButton("Worldwide"); 54 jrbDeluxe = new JRadioButton("Deluxe"); 55 jrbClassic = new JRadioButton("Classic"); 56 57 jcDay = new JComboBox(day); 58 jcMonth = new JComboBox(month); 59 jcYear = new JComboBox(year); 60 61 jbtnSubmit = new JButton("Submit"); 62 jbtnCalculate = new JButton("Calculate"); 63 jbtnClear = new JButton("Clear"); 64 65 /****create JPanels - jpTitle, JpCenterArea & jp2-jp8 , jpBottom + setLayout 66 for ALL JPanels******/ 67 jpTitle = new JPanel(new FlowLayout(FlowLayout.CENTER)); 68 jpCenterArea = new JPanel(new FlowLayout()); 69 jp1 = new JPanel(new FlowLayout()); 70 jp2 = new JPanel(new FlowLayout(FlowLayout.CENTER)); 71 jp3 = new JPanel(new FlowLayout()); 72 jp4 = new JPanel(new FlowLayout()); 73 jp5 = new JPanel(new FlowLayout()); 74 jp6 = new JPanel(new FlowLayout(FlowLayout.CENTER)); 75 jp7 = new JPanel(new FlowLayout(FlowLayout.CENTER)); 76 jpBottom = new JPanel(new FlowLayout(FlowLayout.CENTER)); 77 78 79 80 81 //add components to JPanels 82 jpTitle.add(jlblTitle); 83 84 //jp1 85 jp1.add(jlblName); 86 jp1.add(jtfName); 87 jp1.add(jlblNRIC); 88 jp1.add(jtfIC); 89 90 //jp2 91 jp2.add(jlblAdd); 92 jp2.add(jtfAdd); 93 jp2.add(jlblPostal); 94 jp2.add(jtfPostal); 95 96 //jp3 97 jp3.add(jlblContact); 98 jp3.add(jtfContact); 99 jp3.add(jrbResident); 100 jp3.add(jrbOffice); 101 jp3.add(jlblDOB); 102 jp3.add(jcDay); 103 jp3.add(jcMonth); 104 jp3.add(jcYear); 105 106 //jp4 107 jp4.add(jlblEmail); 108 jp4.add(jtfEmail); 109 110 //jp5 111 jp5.add(jlblPeriod); 112 jp5.add(jlblDeparture); 113 jp5.add(jcDay); 114 jp5.add(jcMonth); 115 jp5.add(jcYear); 116 jp5.add(jlblDays); 117 jp5.add(jcDay); 118 119 //jp6 120 jp6.add(jlblZone); 121 jp6.add(jrbAsia); 122 jp6.add(jrbWorldwide); 123 jp6.add(jlblPlan); 124 jp6.add(jrbDeluxe); 125 jp6.add(jrbClassic); 126 127 //jp7 128 jp7.add(jtfZone); 129 130 //jpCenterArea to hold jp1-jp7 131 jpCenterArea.add(jp1); 132 jpCenterArea.add(jp2); 133 jpCenterArea.add(jp3); 134 jpCenterArea.add(jp4); 135 jpCenterArea.add(jp5); 136 jpCenterArea.add(jp6); 137 jpCenterArea.add(jp7); 138 139 //jpBottom 140 jpBottom.add(jbtnSubmit); 141 jpBottom.add(jbtnCalculate); 142 jpBottom.add(jbtnClear); 143 144 /********Add Jpanels to JFrame*****/ 145 add(jpTitle, BorderLayout.NORTH); 146 add(jpCenterArea, BorderLayout.CENTER); 147 add(jpBottom, BorderLayout.SOUTH); 148 149 setVisible(true); 150 151 152 153 }//end null constructor 154 public static void main(String[] args) 155 { 156 TravelInsuranceApplication travel = new TravelInsuranceApplication(); 157 158 }//end main 159 160 }//end class

    Read the article

  • Trying to make a plugin system in C++/Qt

    - by Pirate for Profit
    I'm making a task-based program that needs to have plugins. Tasks need to have properties which can be easily edited, I think this can be done with Qt's Meta-Object Compiler reflection capabilities (I could be wrong, but I should be able to stick this in a QtPropertyBrowser?) So here's the base: class Task : public QObject { Q_OBJECT public: explicit Task(QObject *parent = 0) : QObject(parent){} virtual void run() = 0; signals: void taskFinished(bool success = true); } Then a plugin might have this task: class PrinterTask : public Task { Q_OBJECT public: explicit PrinterTask(QObject *parent = 0) : Task(parent) {} void run() { Printer::getInstance()->Print(this->getData()); // fictional emit taskFinished(true); } inline const QString &getData() const; inline void setData(QString data); Q_PROPERTY(QString data READ getData WRITE setData) // for reflection } In a nutshell, here's what I want to do: // load plugin // find all the Tasks interface implementations in it // have user able to choose a Task and edit its specific Q_PROPERTY's // run the TASK It's important that one .dll has multiple tasks, because I want them to be associated by their module. For instance, "FileTasks.dll" could have tasks for deleting files, making files, etc. The only problem with Qt's plugin setup is I want to store X amount of Tasks in one .dll module. As far as I can tell, you can only load one interface per plugin (I could be wrong?). If so, the only possible way to do accomplish what I want is to create a FactoryInterface with string based keys which return the objects (as in Qt's Plug-And-Paint example), which is a terrible boilerplate that I would like to avoid. Anyone know a cleaner C++ plugin architecture than Qt's to do what I want? Also, am I safely assuming Qt's reflection capabilities will do what I want (i.e. able to edit an unknown dynamically loaded tasks' properties with the QtPropertyBrowser before dispatching)?

    Read the article

  • Simple POSIX threads question

    - by Andy
    Hi, I have this POSIX thread: void subthread(void) { while(!quit_thread) { // do something ... // don't waste cpu cycles if(!quit_thread) usleep(500); } // free resources ... // tell main thread we're done quit_thread = FALSE; } Now I want to terminate subthread() from my main thread. I've tried the following: quit_thread = TRUE; // wait until subthread() has cleaned its resources while(quit_thread); But it does not work! The while() clause does never exit although my subthread clearly sets quit_thread to FALSE after having freed its resources! If I modify my shutdown code like this: quit_thread = TRUE; // wait until subthread() has cleaned its resources while(quit_thread) usleep(10); Then everything is working fine! Could someone explain to me why the first solution does not work and why the version with usleep(10) suddenly works? I know that this is not a pretty solution. I could use semaphores/signals for this but I'd like to learn something about multithreading, so I'd like to know why my first solution doesn't work. Thanks!

    Read the article

  • x86 Assembly: Before Making a System Call on Linux Should You Save All Registers?

    - by mudge
    I have the below code that opens up a file, reads it into a buffer and then closes the file. The close file system call requires that the file descriptor number be in the ebx register. The ebx register gets the file descriptor number before the read system call is made. My question is should I save the ebx register on the stack or somewhere before I make the read system call, (could int 80h trash the ebx register?). And then restore the ebx register for the close system call? Or is the code I have below fine and safe? I have run the below code and it works, I'm just not sure if it is generally considered good assembly practice or not because I don't save the ebx register before the int 80h read call. ;; open up the input file mov eax,5 ; open file system call number mov ebx,[esp+8] ; null terminated string file name, first command line parameter mov ecx,0o ; access type: O_RDONLY int 80h ; file handle or negative error number put in eax test eax,eax js Error ; test sign flag (SF) for negative number which signals error ;; read in the full input file mov ebx,eax ; assign input file descripter mov eax,3 ; read system call number mov ecx,InputBuff ; buffer to read into mov edx,INPUT_BUFF_LEN ; total bytes to read int 80h test eax,eax js Error ; if eax is negative then error jz Error ; if no bytes were read then error add eax,InputBuff ; add size of input to the begining of InputBuff location mov [InputEnd],eax ; assign address of end of input ;; close the input file ;; file descripter is already in ebx mov eax,6 ; close file system call number int 80h

    Read the article

< Previous Page | 72 73 74 75 76 77 78 79 80 81 82  | Next Page >