Search Results

Search found 12264 results on 491 pages for 'drive letter'.

Page 76/491 | < Previous Page | 72 73 74 75 76 77 78 79 80 81 82 83  | Next Page >

• 0x0000007b WinXP in VirtualBox with no Admin access on source drive

  - by Ozzah

  I have a physical drive with an installation of WinXP-32 which I have made a clone of using SysInternals disk2vhd. I have no admin rights on this installation. I have tried to boot this VHD in VirtualBox, however it blue screens on 0x0000007b. I have researched this and apparently the cause is that Windows doesn't like the IDE controller changing. I have tried all the available controllers in VirtualBox, but they all produce the same result. There is a Microsoft KB article which describes a method involving loading a .reg file and extracting some sys files from a CAB. This method apparently works well for many people with this problem, however it will not work for me as I don't have admin rights on the WinXP installation. Is there anything I can do in this case? Is there any way of loading the .reg file outside the OS? or perhaps doing a repair using the WinXP CD? Even though I have no admin rights on the source drive installation of Windows, I do obviously have full access to the file system directly on the drive and also in the VHD itself.

  Read the article

• HP Storageworks 448 tape drive input/output error with Ubuntu

  - by Dan D

  I'm trying to set a backup to tape of a machine using flexbackup. However any attempt to write to the tape drive (via either flexbackup or just tar) results in "/dev/st0: Input/output error" The machine seems to recognise the drive (HP Storageworks Ultrium 448) and that there's a tape in it and "mt status" seems to work... "mt -f /dev/st0 rewind" or "erase" throw no errors... root@stor001:/# mt status SCSI 2 tape drive: File number=0, block number=0, partition=0. Tape block size 0 bytes. Density code 0x42 (LTO-2). Soft error count since last status=0 General status bits on (41010000): BOT ONLINE IM_REP_EN root@stor001:/# cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: DVDRAM GSA-4084N Rev: KS02 Type: CD-ROM ANSI SCSI revision: 05 Host: scsi2 Channel: 00 Id: 03 Lun: 00 Vendor: HP Model: Ultrium 2-SCSI Rev: S65D Type: Sequential-Access ANSI SCSI revision: 03 "tell" does however root@stor001:/# mt -f /dev/st0 tell /dev/st0: Input/output error Based on a forum post I found, I tried: root@stor001:/# dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 10+0 records in 10+0 records out 10240 bytes (10 kB) copied, 5.0815 s, 2.0 kB/s which gave the person on the forum an error but seems to work for me. If anyone has any suggestions, I'm all ears...

  Read the article

• Boot iMac into Centos from external hard drive

  - by user1704978

  I have Centos 6.3 installed on an external Western Digital drive with Firewire and USB interfaces. I want to be able to boot an iMac (2008, 3.06GHz Core 2 Duo) from this disk. The iMac has Mac OS X 10.5.8 and also a Window XP installation. I have tried holding 'T' on bootup for target disk mode but the external disk is ignored (presumably as it's not a Mac OSX image). I created an rEFit boot DVD which when booted in CD mode (holding 'C' on startup) displays three options, Mac OS (on internal drive), Linux and Windows. Selecting the Linux option unfortunately boots the Mac into XP. Three options are only displayed when the external disk is plugged into the Firewire port. If the external disk is plugged into a USB port the Linux option is not displayed and I can only boot into Mac OS X or Windows. This external disk will happily boot a Lenovo T410 laptop into Centos. My questions are: 1) Is it actually possible to boot into Centos on an iMac with an external hard drive. If so how do I achieve this? 2) Why is rEFit apparently booting from the wrong partition?

  Read the article

• I used disk copy to clone my drive, now my windows 7 profile won't load correctly

  - by RzK

  I used easeuse disk copy, after acronis, clonezilla, windows image restore failed me. Basically it copys all sectors, I set it to skip bad sectors(40). The source drive works, it just gave me a couple errors and stopped booting at one point. The drive is an identical copy, minus 40 bad errors. The drive is set to C and active partition, I rebuilt the boot order. I've ran sfc /scannow and ran chkdsk /r chkdsk found 20kb of bad sectors if I remember right. Now the issue I get is when I log into my profile which was saved right, I get a blank light blue wallpaper (non-license) explorer.exe is not running, and there are only 4 processes running in taskmanager, including taskmanager. I would try a repair install but CRTL-E would not open, nothing will open once I force start explorer.exe, almost like all services are down. What should I do? Fresh install is almost not a possibility I will try and fix this issue. sfc /scannow /offbootdir=c:\ /offwindir=c:\windows returns "Windows Resource Protection could not perform the requested operation"

  Read the article

• How do I use a self encrypting drive?

  - by Unique_Key

  I recently purchased a Micron RealSSD c400 self encrypting drive, and I am having a few issues when trying to get it recognized by my laptop (HP Elitebook 8440p running Windows 7 x64; also tried on a custom-built desktop). When I try to initialize the drive from disk management, I get a CRC error; also, when attempting to partition it from Windows setup, the program can't create the partitions. I also tried with UBCD, nothing. I assume this is due to drive security, but I haven't been able to find much information about this online; do I need a management software or something? I'm completely stumped here. EDIT As requested, when I try partitioning the device from Windows setup I get a 0x80300024 error; when I try initializing it from disk management, I get a "Data error (cyclic redundancy check)" message, and the event log shows the following under System: Source: VDS Basic Provider, message: unexpected failure. error code 490@01010004 (2x) Source: Virtual Disk Service, message: VDS fails to write boot code on a disk during clean operation. Error code: 80070001@02070008 (1x) Source: Disk, message: The device \Device\Harddisk2\DR2 has a bad block (2x) The security logs show nothing related. Also, when attempting to configure it from UBCD (utility: HDAT2), I get an error along the lines of "can't edit partition information" or something to that tune.

  Read the article

• Cannot Install Bootcamp on Mac Fusion Drive

  - by user3377019

  I have two drive installed in my mid-2013 Macbook pro. It is running osx maverick. I set the two drives (an ssd and a regular HD) up using the fusion drive (following the diy fusion drive guides out there). I went ahead and created a 40gb partition to host my windows install. I removed the SSD, installed windows, then reinstalled the SSD. As soon as the ssd was placed back in the bootcamp partition stopped booting. I get a blinking cursor on a black screen. I checked out the partition info in disk utility and it appears that the windows partition is not marked bootable. Below is some info I managed to gather. I am wondering if there is a way to fix the partition table so my bootcamp will boot. /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *120.0 GB disk0 1: EFI EFI 209.7 MB disk0s1 2: Apple_CoreStorage 119.7 GB disk0s2 3: Apple_Boot Boot OS X 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *500.1 GB disk1 1: EFI EFI 209.7 MB disk1s1 2: Microsoft Basic Data BOOTCAMP 40.0 GB disk1s2 3: Apple_CoreStorage 459.2 GB disk1s3 4: Apple_Boot Boot OS X 650.0 MB disk1s4 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Macintosh HD *573.4 GB disk2 Name : BOOTCAMP Type : Partition Disk Identifier : disk1s2 Mount Point : /Volumes/BOOTCAMP File System : Windows NT File System (NTFS) Connection Bus : SATA Device Tree : IODeviceTree:/PCI0@0/SATA@1F,2/PRT1@1/PMP@0 Writable : No Universal Unique Identifier : 584BAED6-4C46-4F18-93B3-957F6E27003C Capacity : 40 GB (39,998,980,096 Bytes) Free Space : 16.34 GB (16,339,972,096 Bytes) Used : 23.66 GB (23,659,003,904 Bytes) Number of Files : 86,424 Number of Folders : 0 Owners Enabled : No Can Turn Owners Off : No Can Be Formatted : No Bootable : No Supports Journaling : No Journaled : No Disk Number : 1 Partition Number : 2

  Read the article

• NTBackup Error: C: is not a valid drive

  - by Chris

  I'm trying to use NtBackup to back up the C: Drive on a Microsoft Windows Small Business Server 2003 machine and get the following error in the log file: Backup Status Operation: Backup Active backup destination: 4mm DDS Media name: "Media created 04/02/2011 at 21:56" Error: The device reported an error on a request to read data from media. Error reported: Invalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. Error: C: is not a valid drive, or you do not have access. The operation did not successfully complete. I'm using a brand new SATA Quantum Dat-72 drive with a brand new tape (tried a couple of tapes). I carry out the following: Open NTBackup Select Backup Tab Tick the box next to C: Ensure Destination is 4mm DDS Media is set to New Press Start Backup Choose Replace the data on the media and press Start Backup NTBackup tries to mount the media Error Message shows: The device reported an error on a request to read data from media. Error reported: INvalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. On checking the log I find the following: Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8018 Date: 04/02/2011 Time: 22:02:02 User: N/A Computer: SERVER Description: Begin Operation For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. and then; Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8019 Date: 04/02/2011 Time: 22:02:59 User: N/A Computer: SERVER Description: End Operation: The operation was successfully completed. Consult the backup report for more details. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• Microsoft Office 2003 applications crash on 'Save As' to a network mapped drive

  - by Archit Baweja

  Hey guys, so I'm not sure if it belongs on ServerFault forums so figured I'd ask here first because its a workstation/client side issue. I have a client where we have windows server 2003 setup, with windows xp professional setup on all the workstations. We've setup a 'domain' and all workstations logon to the domain (authenticated by the Windows Domain Controller), and in the logon script we map drives on to each workstation. Everything is working peachy except for one workstation, where when I open a file in excel from a mapped drive, it opens fine, but when I go to hit Save As, the Save As dialog pops and hangs up. I cannot perform any other action in excel. When I try cancel the Save As dialog, excel crashes. The mapped drive opens up fine in Windows Explorer. To further investigate this issue, I created a new blank text document on the network drive in Windows Explorer. I then opened it. Then hit save as, and the Save As dialog opened up fine and it would let me save the document. I repeated the above steps for a word document. However this time the Save As dialog hung/froze again. So I'd imagine its a Microsoft Office Issue. Any ideas?

  Read the article

• Drive Mapped On Amazon EC2 Instance Startup Disconnected After Logon

  - by jsn

  I am launching an Amazon EC2 instance (Windows Server 2012), and on startup (though User Data field), it runs this powershell script: <powershell> NET CONFIG SERVER /AUTODISCONNECT:-1 # clear all prior connections net use * /delete /y > C:\delLog.txt 2>&1 # mount new drive net use R: \\dbHost\share /user:username pass /persistent:yes > C:\useLog.txt 2>&1 ipconfig /all > C:\ipLog.txt </powershell> When it launches and I connect to it through RDP, it shows in explorer "Diconnected Network Drive (R:). If I double click it, error message displays "R:\ is not accesible. Access id denied". Normally, it would ask me for credentials to reconnect. I need for this drive to be connected through the duration of the instance. delLog.txt contents: You have these remote connections: T: \\dbHost\share Continuing will cancel the connections. The command completed successfully. useLog.txt contents: The command completed successfully. ipLog.txt contents as expected. The net use commands works fine by itself, it connects. Anyone have any idea what could be wrong? There is only one account on these machines - Administrator. It is a samba share to a Linux server on a private network.

  Read the article

• "Path Not Found" when attempting to write to a sub folder within a mapped drive

  - by Adam

  We have an interesting issue with one of our server shares, or possibly, our Win 7 desktops. When our users try to save files in a sub folder, either via copy/paste or through an application, to a mapped drive on our DC they receive an error saying "Path not found". They can however browse this folder and open files from it. This is where the "Path Not Found" error doesn't seem to stack up in my opinion. Users can however save files fine in the root folder of the mapped drive, it appears only to affect sub folders. It seems to be random which users and machines this affects. The users can log on to a different machine and be able to save in sub folders fine, on the same mapped drive. Event viewer hasn't been much help either. Currently, the only solution we have found is to image the machines affected which solves the issue. Our servers are Server 2008 R2 with Win 7 Pro desktops. Any help/pointers/suggestions would greatly be appreciated.

  Read the article

• XP Client for NFS failure dialog on startup, but drive mapping works

  - by Matt Bennett

  I'm mounting an NFS share to some windows machines using the tools that come in the Services for UNIX Administration toolkit. I've set up the User Name Mapping service to use local passwd and group files. I had to manually start the User Name Mapping service, and then created an 'advanced map' from the XP machine's user to a uid that exists in on my NFS server, like so: Windows User: Matt Bennett UNIX Domain: PCNFS UNIX User: mattbennett UID: 10250 Primary: * I can map a network drive without any issues, and it correctly identifies the UID and GID to use, but when I reboot I get this message: "An error occurred while connecting to the NFS server. Make sure that the Client for NFS service has started. If the problem persists make sure Client for NFS service can communicate with User Name Mapping or PCNFS server." After dismissing the dialog, the machine finishes booting and the network drive is there in My Computer with the title "Disconnected Network Drive", but I can open it I can see the network share without a problem, and then it drops the 'disconnected' from its title. It seems like the services are starting in the wrong order or something, so the first attempt to connect fails but subsequent ones work as expected. There don't seem to be any symptoms apart from the dialog box, but obviously something's not quite right. What have I done wrong? Thanks, Matt.

  Read the article

• NTBackup Error: C: is not a valid drive

  - by Chris

  I'm trying to use NtBackup to back up the C: Drive on a Microsoft Windows Small Business Server 2003 machine and get the following error in the log file: Backup Status Operation: Backup Active backup destination: 4mm DDS Media name: "Media created 04/02/2011 at 21:56" Error: The device reported an error on a request to read data from media. Error reported: Invalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. Error: C: is not a valid drive, or you do not have access. The operation did not successfully complete. I'm using a brand new SATA Quantum Dat-72 drive with a brand new tape (tried a couple of tapes). I carry out the following: Open NTBackup Select Backup Tab Tick the box next to C: Ensure Destination is 4mm DDS Media is set to New Press Start Backup Choose Replace the data on the media and press Start Backup NTBackup tries to mount the media Error Message shows: The device reported an error on a request to read data from media. Error reported: INvalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. On checking the log I find the following: Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8018 Date: 04/02/2011 Time: 22:02:02 User: N/A Computer: SERVER Description: Begin Operation For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. and then; Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8019 Date: 04/02/2011 Time: 22:02:59 User: N/A Computer: SERVER Description: End Operation: The operation was successfully completed. Consult the backup report for more details. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• Windows7 shows a drive as full in summary but files, including backup folder, shown on drive are ver

  - by Rob

  I have a drive partitioned so it is seen by Windows as 2 drives: C:\ and D:\ Windows7 shows D:\ as full up in the graphical summary in 'My Computer' summary of all the drives, e.g. the bar graph indicates full and nearly all of the drive's capacity, 108Gb, is full. So I go into the D:\ drive to look at the files, I see several folders. I select them all and the right click menu Properties to count their size, expecting the value to be about the same as what Windows reports in the summary, i.e. nearly 108Gb. But the properties shows the files are very small, Kbs and Mbs, nowhere near 108Gbs. One of the folders is a backup, but its size is very small. I've checked the folder options to show all system files and hidden files too - and counted these in the properties. Something invisible is holding the space. What is happening here? I'm afraid to delete anything if it removes valuable backups. Have I got huge backups here? Why can't I see them? How do I see them?

  Read the article

• Windows 7 shows a drive as full in summary but files shown on drive are very small

  - by Rob

  I have a drive partitioned so it is seen by Windows as 2 drives: C:\ and D:\ Windows 7 shows D:\ as full up in the graphical summary in 'My Computer' summary of all the drives, e.g. the bar graph indicates full and nearly all of the drive's capacity, 108Gb, is full. So I go into the D:\ drive to look at the files, I see several folders. I select them all and the right-click menu Properties to count their size, expecting the value to be about the same as what Windows reports in the summary, i.e. nearly 108Gb. But the properties window shows the files are very small, Kbs and Mbs, nowhere near 108Gbs. One of the folders is a backup, but its size is very small. I've checked the folder options to show all system files and hidden files too - and counted these in the properties. Something invisible is holding the space. What is happening here? I'm afraid to delete anything if it removes valuable backups. Have I got huge backups here? Why can't I see them? How do I see them?

  Read the article

• Microsoft Office 2003 applications crash on 'Save As' to a network mapped drive

  - by Archit Baweja

  Hey guys, so I'm not sure if it belongs on ServerFault forums so figured I'd ask here first because its a workstation/client side issue. I have a client where we have windows server 2003 setup, with windows xp professional setup on all the workstations. We've setup a 'domain' and all workstations logon to the domain (authenticated by the Windows Domain Controller), and in the logon script we map drives on to each workstation. Everything is working peachy except for one workstation, where when I open a file in excel from a mapped drive, it opens fine, but when I go to hit Save As, the Save As dialog pops and hangs up. I cannot perform any other action in excel. When I try cancel the Save As dialog, excel crashes. The mapped drive opens up fine in Windows Explorer. To further investigate this issue, I created a new blank text document on the network drive in Windows Explorer. I then opened it. Then hit save as, and the Save As dialog opened up fine and it would let me save the document. I repeated the above steps for a word document. However this time the Save As dialog hung/froze again. So I'd imagine its a Microsoft Office Issue. Any ideas?

  Read the article

• Explorer.exe hangup during move large file into external drive

  - by PiotrK

  During move large files (700mb+) to external drive formated NTFS via USB 3.0 I've noticed strange things about explorer.exe (I am using Windows 7 up to date) Sometimes after move file the explorer get stuck (ie. it can happen after few files during move of several large files) - moving window freeze and I am unable to kill explorer (via taskmgr, or cmdline TASKKILL). In command line I've got something like this (taskmgr shows that explorer.exe is still running - I've got the same PID every time I try to kill it and no diagnostic message): C:\Windows\system32TASKKILL /F /IM explorer.exe SUKCES: proces "explorer.exe" o identyfikatorze PID 6296 zostal zakonczony. C:\Windows\system32TASKKILL /F /IM explorer.exe SUKCES: proces "explorer.exe" o identyfikatorze PID 6296 zostal zakonczony. If I try to run another explorer.exe process at this point, I got desktop icon and start bar back but I cannot open any explorer window After few minutes explorer.exe finally dies and I am able to rerun it without rebooting File that I moved have two copies - one local and one on the external drive (the original file wasn't delete after move); Both copies seems to contain the same data (same length and CRC info) If this happen during move of multiply files, only some files are moved and one of them have two copies (both locally and on the external drive) What can I do to fix those explorer hangs? Added: The same problem exist when copying files, it hangsup between large files Similar problem exist when I tried to use TotalCommander (x64): copying paused at 80% of one of files, TC didn't hung up (but clicking cancel in copying dialog box doesn't have any effect). During this pause I can't kill TotalCmd.exe just like Explorer.exe Added (2): This problem seems to disappear when I use 32 bit applications (like TotalCommander (x86) ), but I need to do more testing to be sure of this Added (3): There are several errors in event log, source: disk, id: 11, qualifiers: 49156, task: 0, level: 2, keywords: 0x80000000000000 (This may be important, and I forgot to mention this): Main disk is encrypted via Truecrypt (boot-in password)

  Read the article

• Dual hard drive Windows 7 system, modified the registry to get programs to install on second drive, now IE doesn't work

  - by paul

  I have a dual hard drive Windows 7 system, Windows is installed on an SSD (C:) and I modified the registry to try to force programs to install on second HDD drive (another letter). The registry edits are pretty simple, just a few keys in HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion to change the drive letter. For the most part the system is very fast and works great, but IE doesn't work anymore. With IE10, it opens for a flash with a white window then closes. I tried installed IE11 which opens a white window for a few seconds, doesn't respond, then crashes. I've tried all the solutions I could find. This includes resetting the IE settings, "uninstalling" and re-installing IE, which is just turning it on and off in "Turn Windows Features on or off", copying the Program Files\Internet Explorer files onto both/either drives, changing the registry keys back to use C:, lots of rebooting, and safe mode. Nothing has worked. I don't see errors in the event viewer, but I might not know what to look for. Any ideas on how to get IE running? I don't need IE for daily browsing, I just need it for cross-browser testing on sites I build and on the rare occasion a page only works in IE. I don't really want to use a virtual machine, but would be ok with something standalone like tredosoft's, but I'm not aware of something like that for current versions of IE.

  Read the article

• Mapped network drive connection timeout

  - by Terix

  I have server "Alpha" and server "Beta". Server Beta has a shared folder, that is mapped on server Alpha as "X:" On server Alpha there is a .vbs script that runs and take some files on local drive and copy them on X: drive. My issue is if no user log on server Alpha for a long time, it seems like the tcp connection underneath the mapped drive has a timeout, and the vbs script fails on the copy of file. As soon I log with remote desktop on Alpha server, the .vbs is successfull on the copy of the files. I have made many tests, using file logs to check what was happening and I found no way to refresh the connection and let the .vbs be able to copy files unattended.. I have always to log with remote desktop on Alpha server to refresh the connection and let the .vbs copy the files without issues. What can I do to avoid to log every time? The .vbs script runs 3 times a day and is very annoying. I do not have control over server Beta so I cannot change anything there, and I am very limited on changes I can do on server Alpha ( I cannot change registry and that sort of things)

  Read the article

• Backing up 80G hard drive 1G per day

  - by barrycarter

  I want to securely backup my 80G HD, but doing a complete backup takes forever and slows down my machine, so I want to backup just 1G per day. Details: % First hurdle: on the first day, I want to backup the "first" 1G of the hard drive. Of course, there really is no "first" 1G on a hard drive. % After 80 days, I'll have my whole HD backed up... assuming none of my files ever change, which of course they do. So the backup plan/program must also catch file creation/changes as they come along. % The backups must be consistent, in that I can restore my system by restoring the backups sequentially. In other words, "dd if=/harddrive" probably won't work. % The backups should encrypt file contents AND names, but I don't see this as a major hurdle. % Once the backup has backed up everything (even changed files), it can re-backup the first 1G on my hard drive. Even though this backup is redundant, that's OK, because I always want to be backing up something (eg, if I'm backing up to optical media, the older media might start going corrupt). Is there a magic backup plan/program that does this? In reality, I want to do this for multiple machines with multiple drives each, but think that solving the above will solve the general case.

  Read the article

• Formatting a former RAID 0 drive through USB

  - by EXC

  I'll try to be as specific as possible here: I was using two Hitachi 2.5" 500 gb HDDs in my Gateway P-7805u laptop in a RAID 0 configuration. The array was causing the laptop to run extremely hot, however, so I removed them and deleted the RAID array through Intel Matrix HDD manager. I did a clean install of Windows 7 on the original 320 gb HDD that came with the laptop. I never did format the original RAID array HDDs before taking them out of the computer. Now, I am attempting to format the Hitachi 500 gb RAID array HDDs externally through a USB external enclosure. The external HDD drivers install on my clean install OS, but when I go into 'My Computer' there is no external drive available. I cannot format in CMD Prompt because my computer will not designate a drive letter to the external HDD. The drivers install and the HDD is recognized as a Hitachi external drive, but nothing seems to show up in my computer window. I need to know if there is a way to format these drives to NTFS externally.

  Read the article

• Apache mod_disk_cache on a seperate drive

  - by pavs

  how can I set Apache mod_disk_cache on a separate drive from where the OS/Apache is installed? I have set up this on my apache2.conf: <IfModule mod_cache_disk.c> # cache cleaning is done by htcacheclean, which can be configured in # /etc/default/apache2 # # For further information, see the comments in that file, # /usr/share/doc/apache2/README.Debian, and the htcacheclean(8) # man page. # This path must be the same as the one in /etc/default/apache2 CacheRoot /media/cacheHD # This will also cache local documents. It usually makes more sense to # put this into the configuration for just one virtual host. CacheEnable disk / # The result of CacheDirLevels * CacheDirLength must not be higher than # 20. Moreover, pay attention on file system limits. Some file systems # do not support more than a certain number of inodes and # subdirectories (e.g. 32000 for ext3) CacheDirLevels 2 CacheDirLength 1 </IfModule> and it doesn't seem to be caching anything at all. The drive itself is a freshly installed ssd drive formatted with ext4.

  Read the article

• Boot from USB on MediaSmart EX485

  - by Matt Hanson

  I have an HP MediaSmart EX485. I'm attempting to install Vail on it with a USB flash drive and this guide: http://www.mediasmartserver.net/2010/04/26/how-to-install-windows-home-server-vail-on-the-hp-mediasmart-server/. I'm having issues getting the server to boot from the USB flash drive. The MediaSmart itself being headless doesn't help matters. The flash drive has an LED on it for disk activity, and I'm able to see that it's detected when the server is powered on, but it's definitely not booting from it. Any ideas?

  Read the article

• Intel RST crashing! IAStorUI unstable in win 8.1

  - by user269549

  I have a Z87E-ITX Asrock mobo. Using a new 64G Corsair SSD as cache and a new Western Digi Black Scorpion 750G 2.5" drive. Using windows 8.1. Latest software or not, I can't open Intel RST software without it saying IAStorUI has stopped working. A problem caused the program to stop working correctly blah blah. I have had some issues recently with Robotic sounds causing fps drops etc but found it was the HDD. After a standard windows scan and fix (& update to win 8.1) I haven't been able to open Intel RST. I thought maybe I should try to look for an SSD cache drive checker but as it doesn't show up as a drive, I'm unsure how any program can scan it.

  Read the article

• MacBook Pro - 7200 vs 5400 rpm drives - Heat and Noise

  - by webworm

  I am looking at a new 15" MacBook Pro for development purposes. I am planning to run a Virtual Machine for about 50% of my work (Windows 7 x64, IIS, SQL Server, and VS 2010). The upgrade from a 5400 rpm drive to a 7200 rpm is only $45. From what I understand the faster rotational speed of the 7200 rpm drive will help virtual machine performance. However, I am concerned that additional heat and fan noise might be an issue. I will be running mostly on A/C power so decreased battery life is not a major concern for me. Since I would be running with a Core i7 processor which gives off a fair amount of heat already I was wondering if it might be best to stay at 5400 rpm for the hard drive. What do you all think? Thanks!

  Read the article

• SpinRite and USB blues - does a solution exist?

  - by Peter Mortensen

  I use SpinRite to recover hard disks and their content, and to a lesser degree for preventive maintenance. However, if a USB drive (USB thumb drive and/or external hard disk with a USB interface) is connected when SpinRite scans for devices, then SpinRite never finishes/hangs. The work-around is of course to disconnect the drive, but there is value in being able to use SpinRite on USB drives. Some external drives have no screws and it is difficult to take out the hard disk without damaging the casing. And for those that have it would save the disassembling time. Is there a way to fix this problem (e.g. BIOS changes or a modified SpinRite boot CD) without resorting to floppy disks?

  Read the article

< Previous Page | 72 73 74 75 76 77 78 79 80 81 82 83  | Next Page >