Search Results

Search found 3061 results on 123 pages for 'sata hdd'.

Page 76/123 | < Previous Page | 72 73 74 75 76 77 78 79 80 81 82 83  | Next Page >

• How can I unfreeze an SSD connected to a remote server?

  - by chmac

  I don't have physical access to the machine, so I can't unplug the drive. # hdparm -I /dev/sda | grep frozen frozen The advice I've read elsewhere is to hotplug the drive, pull the power / sata cables while the machine is running. Those are not possible in this situation as I don't have physical access. I've tried power cycling the machine through the host's control panel a few times, but that hasn't worked. Is there any way I can unfreeze (unfrozen?) the drive without physical access?

  Read the article

• Can I rebuild degraded RAID1 on a SAS 5 i controller with a larger mirror drive size?

  - by Kenny

  A drive failed on a Dell SAS 5i controller - see controller bios screengrab: http://imagebin.ca/view/SkZbszA.html The primary is a 160GB 10k sata drive. I added a 250GB 7k rpm drive in the hope that the array would rebuild onto this drive. This did not happen. (assuming that the controller would just operate at the speed of the slowest drive) The controller could see the new drive, but it didn't automatically rebuild the raid1 onto this drive. (my assumption is that it did not do this rebuild as the drive sizes are different). There was an option to add the new drive to the existing raid1 array - but when I tried this a message appeared stating that all data on the array would be lost. (I didn't get a screenshot of this message, I will later) Should the SAS 5i allow me to rebuild the array onto a larger drive? Is the option to add the drive to the array the right way to go? Many thanks!

  Read the article

• How to know which block device maps to which physical drive

  - by Karolis T.

  I have a server with software RAID 1, two hot-swap sata disks. One hard drive started showing errors, I'm thinking about removing and replacing it, only problem is that I have no idea which of the two correspond to which devices. And I can't shut the server down to find out. I have /dev/sda and /dev/sdb, /dev/sda is the failing one. Thought about doing something along the lines # mdadm --manage /dev/md0 --remove /dev/sda1 then somehow stop/suspend the drive using tuning software and try to listen which of the two stopped, but that's not gonna work in a noisy server environment. Drive panels have no LEDs. Thanks for any ideas!

  Read the article

• Beeping Hard Disk - Seagate 250GB Momentus 5400.6

  - by Pez Cuckow

  I have been trying to repair a laptop that simply beeps instead of booting. After taking it apart I have now realised that it is the hard disk beeping. I know that may sound strange but I guarantee that is what it is! (Currently powered on it's own with a Sata Mains lead). The beeping is slightly faster than one per second there is a link to this recording. This recording was made resting the mic on the hard disk while it was sat on a table on it's own, there are no speakers anywhere near, the sound is coming from the hard disk. Does anyone know what this beep means? Is the hard drive just dead, or is it fixable and the data recoverable? Many thanks,

  Read the article

• eSATA hotswap using Jmicron JMB363 controller

  - by Stephen

  I have tried both IDE and AHCI modes in the BIOS. Also tried many different driver revisions. I can't seem to hot swap an external SATA drive. I can use the wizard to safely remove it, but reconnecting doesn't do anything unless I reboot. I use a thermaltake dock, and I would like to swap in my backup drive sometimes to do images (they take all day over USB). I can reboot, but I'd like to use hot swap. The controller is a Jmicron JMB363. I'm using the latest BIOS on my motherboard, as well.

  Read the article

• ASUS P6X58D and 12 GB of RAM

  - by Hunter

  I just assembled my new PC and it screams, BUT it's only recognizing 8 GB of RAM in BIOS and OS rather than the installed 12 GB. In the BIOS the RAM was registering at 1066 MHz so I set it to 1600 MHz. I updated the BIOS to the latest non-beta release. http://www.asus.com/product.aspx?P_ID=wurRaDZ8lo4Ckukj OS: Windows 7 Ultimate 64-bit Motherboard: ASUS P6X58D Premium CPU: Intel Core i7 920 RAM: CORSAIR XMS3 12 GB (6 x 2 GB) 240-Pin DDR3 SDRAM DDR3 1600 HDD: Intel 80 GB SSD SATA II Power supply: Kingwin 1000 W Modular I've installed the Beta BIOS 0808 but no luck!

  Read the article

• Recovering portion(s) of file with CRC (cyclic redundancy check) errors in Robocopy

  - by Mark A

  Is it possible to recover portions of files with CRC errors? If so, how? I have a partially damaged hard drive (2.5" SATA) that I have partially recovered using Spinrite 6.0 (took 2 weeks to run!). I have been successful in getting many of the files off of the drive using Robocopy . /V /S /E /COPY:DAT /R:1 /W:0, but some of the files get to +/- 90% in Robocopy and then fail with a CRC Data Error (cyclic redundancy check). I am wondering if it is possible to recover the first 90% of the file and try to recover it in a text editor. 1.0% ... 91.0% 91.1% 2010/06/14 18:21:13 ERROR 23 (0x00000017) Copying File F:\Documents and Settings\user\Local Settings\Application Data\Identities\{GUID}\Microsoft\Outlook Express\Mailbox Folder.dbx Data error (cyclic redundancy check). Thanks in advance!

  Read the article

• dell poweredge 860 always pxe boot

  - by Berto

  Hi, We bought a dell poweredge 860, and installed windows server 2008 std. So far so good. Now everytime the server reboots, it try's the pxe boot, and hangs on "cant find pxe bootable, press f1 to continue or f2 to setup". Now, i tried all the settings in the bios (it's the latest - A05), i have the nic active without pxe (i also tried with the nic off)... well, i tried everyting off and on the bios and it still goes to pxe booting. I have one sata drive, that is boot's after the f1. I would like to keep the system updated, but i can't because of the reboot, can someone point me to some direction? Can i give any more information of the server? If yes, what do you want? It has been a week on google trying to figure out this one. Thx

  Read the article

• Windows 7 external 2.5 hard drive read write permissions format

  - by user76918

  Working with Windows 7 professional. While trying to format western digital 250GB sata laptop drive; receiving error not initialized. Went to elevated command line to diskpart to clean all; received error message write protected. Went to Disk Management & Virtual disk drive shows as disk 2 not initialized. No format options available greyed out. Went back to command line tried to see attributes disk is read only. How do I take owner ship to change the permissions & format.

  Read the article

• HP ML115 with P400 Smart Array Controller

  - by John

  Hi, I have a HP ML115 server I have installed a HP P400 Smart Array Controller card, I also have 4 x 1TB Samsung Hard drives. I'm unable to get the the controller to detect the hard drives, I have changed the drives to SATA 1.5G without luck, I have also tried connecting a single 80GB Maxtor drive without luck The controller shows up just after boot and tries to initialize, The controller does not show up in the POST prompt, although I can see the controller when booting off a ACU CD THe controller firmware is a little old v4.12 but I have no way to update it. Any ideas on how I can get this going?

  Read the article

• Setting up a Windows Server 2008 R2 DC + Fileserver : native or virtual?

  - by user126890

  I want to deploy a new DC + Fileserver using Windows Server 2008 R2 SP1 Standard Edition on a Dell PowerEdge R410 and iSCSI storage for a small business (~30 people). Should I install the system native on the server or use a virt layer? I don't have a budget for virtualization so i gotta go with something free... What's a better working routine, taking snapshots of vm's or taking backups (Acronis/CloneZilla) of systems? If I use a virt system, I need a GUI for some people in the business to reset the system to a earlier state in emergency situations. I wanted to install phpVirtualBox once but never finished, is it suitable in a productive environment? server specs: Intel Xeon E5620 CPU (2,40GHz, 4C, 12MB Cache) 8GB RAM Dual Rank LV RDIMMs 1333MHz 2x 1TB SATA 7,2K 3,5, RAID1

  Read the article

• Fedora 11 System - Failed Hard Drive Removed, and Boot gets GRUB Hard Disk Error

  - by user38030

  Greetings, I have a machine with a 120GB ATA drive that has what I thought to be non-essential data on it. I also have a 320GB SATA hard drive with the OS/Application/Files (good data I want to keep). My 120GB ATA is failing I believe, as my computer kept slowing to a halt. However, when I move the drive from BIOS my computer will not start, says "GRUB Hard Disk Error". I know that my Fedora system has an LVM setup. I am looking to just remove the 120GB drive from "the mix", and just have one hard drive. How do I recover ? Thank you. I have access to a Linux Live CD right now and can make any changes. However, it won't boot into my OS - it fails.

  Read the article

• Disk Redundancy across different server

  - by Mascarpone

  I have 3 servers, all with the same specs: Intel CPU 8 GB RAM Linux or BSD Single 2TB desktop SATA with more than 10K Hours of operation, with only less than 300 GB Used My provider cannot install a second hard drive, but can guarantee me that the drive will be replaced immediately in case of failure, with another equally crappy drive. The likelihood of drive failure is high, and since I can't use RAID, I was thinking about keeping a back up of each machine on all the other machines, so that there are always 2 copies on 2 different drives, plus the original. I would synchronize the drives every hour, with rsync, to guarantee some sort of redundancy, since bandwidth inside the DC is free, so it would be much cheaper than offsite backup. (A daily offiste backup is kept anyhow). What do you think? Any suggestion?

  Read the article

• Dual boot Windows XP 32 bit and Windows 7 64-bit

  - by Santanu Roy

  My system config is AMD phenom-II x2 550 processor, 2x2gb(800fsb)ddr2 zion ram, gigabyte ga-m61pme-s2 motherboard, 160gb sata hdd. Now I am planning to install Windows XP sp3 (32-bit) and Windows 7 (64bit). My first questions are: Is my system enough for the above mentioned two OSes? Which OS one should be installed first on local disk c: drive? I have both XP and vista drivers on separate disks as provided with my motherboard but don't have drivers for win-7, so can I use my vista driver for win-7?

  Read the article

• Snap Server 18000 connection help!

  - by sicko666

  I wonder if anyone here can help me. I have a home server setup made up of old secondhand computers, 2 servers running Windows Server 2003, 1 workstation running Windows 7, a 16 port switch & an adsl ethernet modem. All these connect and talk to each other fine but then I got a "Snap Server 18000" and a "Snap disk 30sa" sata array. When I turn the Snap on, it boots past the BIOS, runs a kernel, then displays: This device cannot be managed via the video/kbd/mouse interface. The video is now disabled. You may access the management functions from your web browser. Only, none of the other PCs detect it, so no browser can find it! I have checked all cables, and all LEDs indicate there's a connection. I have installed the windows "iscsi" and the adaptec "Snap Server Manager" on all PCs but still it's not detected. I don't know what else to do, please advise!

  Read the article

• Installing raid controller forces reinstall of Windows Server 2008

  - by Tyler

  So, I've tried two different RAID controllers that have external SATA connections on my Server 2008 machine. I can install the hardware, boot into Windows, install the drivers and reboot again. No problems. However, as soon as I try to use eSATA-connected drives and reboot something happens to the Windows install and I can no longer boot into Windows. I tried repairing from the command line, and the end result is that repair console tells me I have 0 Windows installations (?). I end up having no choice but to reinstall Windows to get back on track. I must be doing something fundamentally wrong here, but I don't know what :(

  Read the article

• Defragment an Exchange Volume

  - by IceMage

  The Scenario: I use a dedicated volume (RAID volume) to store all of my data for my Exchange 2007 server. Today, out of curiosity, I decided to check up on how fragmented the files on this data volume were. To my surprise, the answer is extremely. So, a three part question: First and Foremost, SHOULD I defragment this volume (after a full backup of course)? Be specific as to why not if I should not, or reasons I absolutely should if I should. Second, about how much time should I allow for during this maintenance period per gigabyte. The drives are all 7200 RPM SATA drives on a Hardware RAID 5 controller (Perc 5i/6i, can't remember), the files are extremely fragmented. (Over 5000 file fragments per gigabyte). Third, is there something wrong here? It seems to me like the drive shouldn't be this fragmented. Could something be configured incorrectly that could be causing this to happen?

  Read the article

• Windows 7 Slowness following Virtual PC and Visual Studio Install

  - by Elliot Hughes

  I'm running Windows 7 32bit on a 3.2ghz Pentium D with 2gb RAM and a 1TB SATA hard drive. My system was running as fast as it ever has until I installed Visual Studio and Virtual PC a few days ago. Ever since - regardless of whether either application has been running the system has been running incredibly slowly. For example flash video plays jumpily, 3D games that used to run fine are now unplayable and even the smallest amount of multitasking makes the system unusable. I'm confident there is no virus or other such things present following scans in safemode and I'm fairly confident I've made no other changes to my system. Any ideas - I've run out of things to try!

  Read the article

• Setting up a laptop hard drive as a secondary on a tower?

  - by vermiculus

  I'm trying to install Windows 8 for a friend who has recently bricked a laptop hard drive. The new one is OEM so there is no OS - I need to be able to stick it in to my tower and load the new OS on it. Both bricked and replacement laptop hard drives are SATA and connect to my mobo just like any other. After I post this I'm going to check the BIOS and see if it shows up, but so far I don't have it showing up in Disk Management. Any ideas would be greatly appreciated.

  Read the article

• What things should I run daily, weekly, monthly on my Windows machine?

  - by Jitendra vyas

  What things should I run daily, weekly, monthly on my Windows XP machine? De fragmentation Scan-disk Full system scan Disk clean up Trojan checker malware remover or any other thing... And should I run all these things in Safe-mode always? I want to perform all mentioned things automatically at night. How to set schedule and What would be the best plan? For daily weekly and monthly? I've 300 GB SATA HDD with 6 partition. I would like to know in above mentioned list: Which process should I run daily? Which process should I run weekly? Which process should I run on monthly basis How to set schedule for all in Windows task scheduler?

  Read the article

• GRUB Problem or Hardware Problem?

  - by Nikit Batale

  I have Windows XP Professional and Ubuntu Karmic Koala 9.10 on dual boot. I often get a GRUB loading failed error during boot-up. Or sometimes, when I try to boot into either Ubuntu or XP, I get a Could not read from source error. Now this is funny. After getting one of the above errors, if I simply unplug the SATA cable from Hard Drive end and plug it again, the problem gets solved. So what and whose problem is it? GRUB or My Hardware ? P.S.: I was suggested on StackOverflow that ServerFault is the right place for this question.

  Read the article

• Proper use of disk to disk to tape backup using de-duplication and LTO5

  - by Michael

  I currently have ~12TB of data for a full disk to tape (LTO3) backup. Needless to say, it's now requiring over 16 tapes so I'm looking at other solutions. Here is what I've come up with. I'd like to hear the community's thoughts. Server for Disk-to-Disk BackupExec 2010 Using De-duplication Technology 20+TB worth of SATA drives LTO5 robotic library connected via SAS 1Gbps NIC connected to network What I envision is doing a full backup of my entire network which will initially take a long time over the 1Gbps NIC but once the de-duplication kicks in backups should be quick. I will then use the LTO5 to make disk to tape backups and archive those accordingly. What does everyone think? Any faster way of doing the initial full backup over the 1Gbps NIC? What will be my pain points? Is there a better way of doing what I'm trying to achieve?

  Read the article

• Should I install Windows 7 on a 3 years old PC?

  - by Jitendra vyas

  This is my PC configuration, Should I upgrade my Windows XP to Windows 7. Currently I'm using Windows XP SP3 32 bit. Now will I get same performance or better performance or bad performance if I install Windows 7 on this system? Or would sticking with XP be better? Memory (RAM): 1472 MB DDR RAM (not DDR 2) CPU Info: AMD Sempron(tm) Processor 2500+ CPU Speed: 1398.7 MHz Sound card: Vinyl AC'97 Audio (WAVE) Display Adapters: VIA/S3G UniChrome Pro IGP | NetMeeting driver | RDPDD Chained DD Network Adapters: Bluetooth Device (Personal Area Network) | WAN (PPP/SLIP) Interface Hard Disks: 300 GB SATA HDD Manufacturer: Phoenix Technologies, LTD Product Make: MS-7142 AC Power Status: OnLine BIOS Info: AT/AT COMPATIBLE | 01/18/06 | VIAK8M - 42302e31 Motherboard: MICRO-STAR INTERNATIONAL CO., LTD MS-7142 Modem: ZTE USB Modem FFFE CDMA :

  Read the article

• PCI max throughput

  - by allentown

  Hypothetical here, but I want to understand. Say I have a hand me down machine, 4 PCI slots, 64-bit 33 MHz PCI. How much data can that PCI bus handle? System bus is 133 MHz. I want to use one slot for a SATA II card, and the rest for Gig-E cards, building out as fast a NAS as I can. I think one slot may be AGP2x, so that leaves me 2 for Gig-E and one for SATAT II. Will I saturate, what is the max bandwidth of the PCI bus?

  Read the article

• Replacing an ATA-100 hard drive

  - by Pieter

  I was instructed to replace the hard drive in an old laptop, a Dell Latitude D505. I'm suspecting that there was a head crash when someone moved the laptop while it was turned on. In the specifications, I found this about the hard drive: 30GB ATA-100; (4200RPM); 40GB ATA-100 (5400RPM); 60GB ATA-100 (4200RPM) *Optional 40GB (5400) 2nd HDD Module for media bay I'm familiar with SATA and IDE, but ATA-100 doesn't ring a bell. What do I have to take into account when I go look for a replacement hard drive?

  Read the article

< Previous Page | 72 73 74 75 76 77 78 79 80 81 82 83  | Next Page >