Search Results

Search found 3061 results on 123 pages for 'sata hdd'.

Page 80/123 | < Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >

  • How to install Windows 7 on Acer Aspire iDea 500?

    - by Martin R-L
    I've got a Windows 7 Ultimate 32-bit from MSDN Subscriber Downloads. The downloaded ISO boots fine from both a USB pen drive and a DVD on other computers. On the Acer it doesn't boot. The Acer iDea 500 can boot, and install, Windows XP Mediacenter from a DVD with slipstreamed SATA drives on it. Also, all kinds of Linux distros works perfectly fine on the iDea 500. I wouldn't mind using Mythbuntu instead of Windows 7 Ultimate, but it doesn't work very well.

    Read the article

  • .AVI Files randomly cease to open, other strange errors too

    - by Ben Franchuk
    I Recently (a couple weeks ago) downloaded the complete series of Seinfeld, all in varying file type. I Watched them in sequence according to season and to airing date, and all was well. All of the files played fine with my media player of choice ("BS Player"), and once I had finished, I went onto watch some other TV I had previously downloaded (The U.S. Series of "The Office"), and after then, some other film and then some music, over the following weeks (keep in mind all of these files are all on the same Hard Drive). Later then, More recently, I Went back to watching Seinfeld. The episodes played well as they did before- with the exclusion of a few in Season 7. I Have not tested all of the episodes in the season, but upon inspection, the majority of them are experiencing this problem; the problem being simply that they don't open! BS Player says that the files are either damaged or that the codecs to play the files are not on my computer-- however I am certain that the files DO have the codecs, and I am pretty sure that they are NOT DAMAGED either. I Have played the files with other players (such as VLC, Media Player Classic, and Windows Media Player), too, only to the same result; of them not opening. Seemingly the only way that I can differentiate between a damaged file and a non-damaged file are the way that the icon shows in Windows Explorer. For example, the below image is how explorer shows the information of a file that is non-damaged... ...and below is how a damaged file appears... The most disturbing and confusing part of this, though, is the last episode in the season- It opens, but not as a video- Instead, as a 1 Hour, 16 Minute, and 35 Second Audio file! The file plays a song for the first 4 or so minutes, and then is pretty much silent (except for some extremely quiet noise) until the last minute or so, when a random array of chopped up sounds and beeping noises play. I Do not recognise the song at the beginning of the file, but by the sounds of it, it is a song by the artist "Mr. Oizo," who's complete works I downloaded a couple weeks before now; and a bit before then I had finished downloading season 9 (not affected by these problems) of Seinfeld. I'd also like to note that the file I told of earlier (which played audio instead of video) reads as the same size as the other files in the season (around 175 MB) and also opens as a video clip. I Have NEVER experienced any of these problems in the past, and they seem to be only effecting the one season of my downloaded TV. The problems have not arisen with any of the other files on my Hard Drive, or any of the files downloaded around the time or after the time of which I downloaded season 7 of Seinfeld- or at least to my noticing. I Use the hard drive these files are located on almost every day, so could that be the cause of these problems? Is this a sign that my HDD is soon going to die? If it helps, the HDD is a Western Digital MyBook 1.5 TB 7500 RPM. It is connected to the computer via U.S.B. 2.0. EDIT! I noticed that this problem is now occurring with Season 9 of Seinfeld- and, presumably, other files on the drive I have yet to check. Please, If you have ANY IDEA AT ALL on what may be causing this or how to fix it, do tell me!

    Read the article

  • FreeBSD after motherboard replacement; should I have any concerns?

    - by cc
    So after three years my motherboard (Asus M2N-0MX) has died off. As I go shopping for i's replacement tomorrow I have a concern about the data that I currently have on the drives wtihin. I'm currently running BSD 6.2, and am wondering if there would be any concern with installing a new OS on that system, would it be better to jsut install the latest BSD version, and are their any pitfalls that I should watch for to make sure I don't end up losing 750gb's of data. The setup consists of the following(to the best of my knowledge): Pioneer DVD drive 3ware RAID card four 250gb SATA drives in RAID 5 config thanks to anyone that can offer some advice, or just to confirm if I am over thinking things.

    Read the article

  • Dell XPS 710 - Boot Device Not Available

    - by WilliamKF
    Recently I was gifted a Dell XPS 710 tower running WinXP SP3. It was running fine until today when I restarted and received a blue screen and the error "unmountable boot volume". In order to fix this issue I've attempted to boot from the Windows XP CD and run chkdsk. However when I attempt to boot from the CD drive I get a "Boot Device not Available" error. Next I made a bootable USB flash drive, but receive the same error as the CD drive. The BIOS recognizes the CD and flash drives, and they appear in the boot device list, but neither will boot. I've attempted to resolve this by re-arranging the boot order in the BIOS and switching IDE channels/setting jumpers on the drives themselves, to no effect. I cannot move the hard drive to another machine because the XPS is the only one that supports SATA drives.

    Read the article

  • Windows 7 just restarts, no BSOD, shows "Event ID 14 volsnap"

    - by Mdc007
    My Windows 7 just restarts without giving me a BSOD. When it reboots, it will hang sometimes and you have to let it rest. Sometimes it will print a message saying that Hal.dll is missing or corrupt. When it does restart I can't run a backup or a clone drive – it comes up with constant errors. I tried to run chkdsk – it says everything's clean. What is really puzzling is SyncToy on a different drive hangs half way through and won't run either. Machine: OCZ SSD Agility 2 for C drive SATA HDD for programs, documents on D drive MSI AMD 880 chipset Event viewer says something about critical power failure I/O operations and "Event ID 14 volsnap" – but that is just telling me the computer powered off which I already know.

    Read the article

  • Windows 7 Recurring Blue Screens: MEMORY_MANAGEMENT 0x1A

    - by Chris C.
    I have recurring BSODs that really have me scratching my head. Here's a look at the errors: MEMORY_MANAGEMENT 0x1A (ntoskrnl.exe) - I've seen this 9 times since April 2012 NTFS_FILE_SYSTEM 0x24 (Ntfs.sys) - this one's new, happend 4 days ago BAD_POOL_HEADER 0x19 (win32k.sys) - also new, happened 7 days ago My system specs: Intel Core i5 2500K @ 3.30GHz ASUS Sabertooth P67 Motherboard (Rev 2) * RMA'd my Rev 1 due to recall 16GB (4 x 4GB) Kingston HyperX 1600 MHz DDR3 RAM 2 x 640GB Western Digital Caviar Black 64MB SATA HDD EVGA NVIDIA GeForce GTS450 1GB PCI-E 2.0 Graphics Card I've got Windows 7 Home Premium and it's completely patched. I'm also running Microsoft Security Essentials, which is up-to-date and always present. I've run MemTest86+ from a USB drive for up to nine hours, giving my RAM a total of 6 passes, and it didn't detect a single error. I've used chkdsk in Windows 7 to scan the C:/ drive on boot (twice) and it found no problems. How can I find out what's causing all these blue screens?

    Read the article

  • Understanding why a 450W power supply is destroying my ATX motherboards but not mATX

    - by T. Webster
    Maybe I'm missing something really obvious here, but after going through 3 new motherboards in trying to build my new machine, I'm finally certain that the 450W power supply I bought has been destroying them. It seems like it should be simple: just connect the connectors where they fit and switch the thing on. But today after hooking it to my ASUS Sabertooth 990FX TUF Series Motherboard and switching it on, I could see and smell the smoke coming out of the motherboard. What I don't get is why I can hook this same 450W power supply up to my mATX motherboard and not run into the same problem. What am I missing here? Where on the box or manual is this? (I have 8x2 GB RAM, AMD FX-4100 3.6GHz CPU, 1 512MB ATI graphics card, 1 WD 7200 RPM SATA hard drive. )

    Read the article

  • Setting up Raid 1 Array for Home Server

    - by user1048116
    I'm not sure if this is even possible, but it's worth asking on here! Essentially I have a old machine at home (well, not old hardware wise, but I recently built a new gaming rig), which I decided to install a copy of W2008 R2 on and use as a file/backup server and media center'ish machine. As of now, it has a single drive partitioned into C and D, with D being the Data partition. I have happened to find an old 1TB SATA drive lying around at home, and was wondering if it's possible to setup a Raid 1 array in my rig within Windows without needing to lose everything on my first drive (or maybe even just mirror a specific partition, say the Data partition, as this is just what stores my photos etc). Maybe this isn't possible, but you never know :) Regards, T.C

    Read the article

  • Why is Windows Explorer not responding?

    - by William Barnes
    I am having the seemingy popular problem with Widows Explorer not responding. I have tried the AUTRUNS and turned off everything recommended. I have run SCANNOW 3 times and it comes back clean. When booting in safe mode it appears to work. I read someplace that the problem could be a service program, but can't remember where I read it or how to do it. Something about turning off all service programs and then turning them back on one at a time. The problem is I don't remember what it said to do. Any and all help is greatly appreciated. as an FYI here is my system stats Sorry I can't access that part of control panel right now because windows explore not responding. I have an HPdesk top with a AMD quad core processor 1.8GB 1.5TB sata drives (a 1TB and a 500GB) Nvidia 8400 graphics card a 2mb internet connetion wireless 2 DBD R?W drives. Any help is greatly apprciated

    Read the article

  • What specs to consider when buying SSD?

    - by penyuan
    When I bought "traditional" hard drives, I have been told to consider specs like RPM (5400, 7200, etc.), buffer size (16MB, 32MB etc.), and interface (IDE, SATA, etc.). (did I miss something?) What about solid state drives (SSD)? What are some important specs to consider in terms of performance and reliability? By the way, are SSDs just as reliable as traditional hard drives now? A couple years ago I heard they're not, but that's a "long time" ago now. Thanks for your answer.

    Read the article

  • VMware + SQL Server - sqlserver.exe not using both CPU cores

    - by fistameeny
    Hi, I am working on a virtual machine that runs SQL Server Express (as part of Sage Line 50 Manufacturing). The details are as follows: Physical Server (host machine) - Intel Xeon Quad Core 2.1GHz - 4GB RAM - VMDK image stored on RAID-5 500GB SATA drives (7200RPM) - Running Ubuntu 10.04 Server 64 bit - VMware Server 2 Virtual Machine - Windows Small Business Server 2003 - Allocated 2 vCPU's and 2GB RAM - Using 100GB pre-allocated flat VMDK file The problem I have is that there is process that runs in SQL Server that is CPU intensive. On the old physical server that we migrated to the virtual machine from, this would utilise both CPU cores so the sqlserver.exe process would be running 100% on each of the CPU cores. On the virtual machine, it only seems to use one of the two CPU cores, meaning that the process is much slower to run. Question Is there a way to force SQL Server (sqlserver.exe process) to use both of the CPU cores, and distribute it's load between them? Is this a VMware setting that needs changing to allow processes to use both cores?

    Read the article

  • Run disk error check on NTFS file?

    - by paulius_l
    I have a feeling that my system hard drive is dying. Benchmark kind of enforces it. Here is the benchmark of my system hard drive during low system activity: And here is the benchmark of backup drive: Furthermore, there are some files which I just can't touch because I get CRC errors and the hard drive activity spikes to 100% with operating speeds less than 1 MB/s while working with such files. I haven't yet tried swapping SATA cable as I have read this might cause the problems. Anyway, I would like to run some tests on specific clustsers where those files I am interested in are stored. I don't want to do the full chkdsk because it takes a very long time. I would like to either find the utility which executes the disk check directly on the clusters where the file belongs or a couple utilities where one tells me the cluster locations and another can check just those locations. How do I check and possibly fix disk errors where the files I am interested in are stored? Edit: S.M.A.R.T. info:

    Read the article

  • Windows XP , HP , IntelInside Trobelshooting

    - by Jamil Hneini
    My Windows XP PC has stopped booting. On start up, before Windows boots a screen appears saying: Windows Could Not Boot: Could Not Find or Corrupted file <Windows root>\Sytem32\Hal.dll Please Reinstall the file... From that I understand that I have to reinstall the OS but my computer is so old that I have lost the backup and recovery disk. My Computer's Info: 32Bit Computer Pentium 4 Windows XP Service Pack 2 HP History: My Computer has 4 hard drives 2 internal 40 GB drives (C And D) 2 external 8GB drives (E And F) Additional Info: I need the files inside C And E The computer reads my flash drive as a hard drive (8.45GB)(I have never booted while my USB pluged in while I was troubleshooting) With some test I discovered that the C drive wasn't detected by the computer I have already configured the boot order of BiOS I have Set The SATA to IDE The Question: I have a setup for windows 8 32 bit how can I boot from my USB to run that setup? If that isn't the proper way to handle this problem please tell me the proper way.

    Read the article

  • SAN/NAS with high availability?

    - by netvope
    I have two servers that I plan to use for storage. Each of them has a few SATA disks directly attached. I want the storage to be available even if one of the storage servers is down (preferably the clients wouldn't even notice that the fail-over, although I'm not sure if this is possible). The clients may access the storage via NFS and samba, but this is not a must; I could use something else if needed. I found this guide, Installing and Configuring Openfiler with DRBD and Heartbeat, which apparently does the thing I want. It relies on three components, Openfiler, DRBD, and Heartbeat, and all three of them need to be configured separately. I'm wondering are there simpler solutions? Is using DRBD+Heartbeat the best practice for a situation like mine? I'm also interested to know if there are alternatives that don't depend on DRBD.

    Read the article

  • Time randomly changing itself, internet randomly dying

    - by Vee
    Operating System MS Windows 8 Enterprise 64-bit CPU Intel Core i7 2700K @ 3.50GHz 45 °C Sandy Bridge 32nm Technology RAM 8,00 GB Dual-Channel DDR3 @ 800MHz (8-8-8-24) Motherboard ASRock Z77 Extreme4-M (CPUSocket) 40 °C Graphics SMXL2270HD (1920x1080@60Hz) M2094D-PZ (1680x1050@60Hz) 896MB GeForce GTX 275 (CardExpert Technology) 57 °C Hard Drives 466GB FUJITSU MAXTOR STM3500320AS (SATA) 39 °C Optical Drives ASUS DRW-2014L1T Audio High Definition Audio Device Hello everyone, I installed Windows 8 RTM a few weeks ago. It's not my first time installing it, but it's the first time having two annoying problems: 1) Randomly, the system clock changes time all by itself - to fix it I have to open the time window and sync it with the internet. 2) Randomly, internet connection stops working - to fix I have to run troubleshooting. Windows will find a problem with IP on the "Ethernet" connection and fix it. 3) In rare occasions, my PC freezes and I need to restart it (a BSOD once happened, but after that only freezes) How can I permanently solve these problems? This is what I've already tried: Reset Virus scan Stop/reset the Windows Time service Disable/re-enable Windows Time automatic internet sync Change time from BIOS Change motherboard battery

    Read the article

  • How full is too full for mechanical hard drives?

    - by Sunny Molini
    I have heard many claim that it doesn't matter how full a drive is until it starts cutting into temp and virtual memory space. This doesn't make sense to me, given the nature of how the data is transacted on a hard drive. The inside of the platter presents less data per revolution than the outside of the drive does, by significant factors. The inside 40% of the radius of full size hard drive is used for the spindle, so only the outside 60% is used for data storage, but that still means that the inside track of a hard drive presents data 60% slower than the outside track. By my calculation, a Hard drive that is only 10% full should perform about 2.25 times faster than a hard drive that is 90% full, assuming that the flow is constrained by other factors. Am I wildly off base here? For all the drives I know, even the top speeds of the first 1% of the drive would be well within the bandwidth provided by a SATA 2 connection.

    Read the article

  • how to change the default open-with program to a program on the second disk

    - by Scott????
    I have a 250GB HDD for my system and a 60GB SSD using a SATA port. I installed most of my applications on the SSD. There's a strange thing though. I can not change the default open-with program to a program which is on the SSD. I think it may be caused by permission so I gave my user a 'full control' permission on the security tab in disk properties. But changing permissions is not work. After I choose an application (I've tried Notepad++, Sublime, 7Zip, etc.), nothing is added in the below window: Also, if I install 7Zip on my machine, the right click menu items can not be added.

    Read the article

  • Getting BootMgr not found errors repeatedly on Win7 x64

    - by abszero
    So here is the basic configuration of the box: Primary RAID 1 (Mirror, Bootable): 2x 300GB WD SATA drives AMD Phenom Quad Core x64 @2.2 ASUS M3N78 Pro Board 4GB RAM Win 7 Ultimate Additionally, this box is a Host OS for several CentOS Boxes via VirtualBox. The box runs like a champ but, for whatever reason, everytime I restart the machine I get a BootMgr not found error when the box tries to boot. I pop in my Win DVD, select 'Repair Windows' then 'Fix Start Up Problems' and everything works fine...once. When I restart the box again I have to go back through this process. Any ideas on what is going on?

    Read the article

  • FreeNAS/ZFS/Raid-Z slightly different disks

    - by muskratt
    I'm considering using FreeNAS and "recycling" some of my older 1TB disks. Two are the exact same model Western Digital while another is Seagate and the fourth is Samsung. Typically, since all disks are not equal, I'll create my arrays on a Windows-based server 1GB undersized to prevent a replacement disk not being large enough. Dell is notorious for sending replacement SATA disks of different brand---knock on wood, no problems yet. Since not all drives are created equally and they can vary a few MBs, is there a way to make the the FreeNas/ZFS/Raid-Z function in the same way I do for my Windows-based servers above? Thanks

    Read the article

  • Would hybrid drive work after SSD failure

    - by lulalala
    Hybrid hard drive combines SSD with traditional hard drives. I know that SSD can fail much often than traditional hard drives. So I want to ask that, when the SSD part of the hybrid drive fails, would I still be able to use the traditional hard drive? If it won't work like that, then I will consider add-in SATA cards instead, as it delegates risk much better. EDIT: I guess it differs from model to model, so if yes what models would work. (I am evaluating Seagate DX for now)

    Read the article

  • ACHI drivers for W8.1 with amd

    - by LeiNaD_87
    I hope you can help me... I just installed a SSD (Samsung EVO 840) and windows 8.1 pro in my pc with M5A99X EVO ( chipset AMD 990X/SB950 ) motherboard. The SSD is installed in sata3 socket using a sata3 wire. The AHCI mode is ON in the bios. I configured the ahci controller and now device administrator looks like this: All works, but the speed of the SDD is very slow (like a HDD). Samsung magician doesn't recognize the sata mode neither the ahci. I tried to install more drivers but the system broke and I need to reinstall windows :( I tried many things from the web, but any works: Modify windows registy Use compatibility mode Modify the amd drivers and install it unsigned Thank you for your time!! EDIT to add a CrystalDiskMark benchmark

    Read the article

  • Windows 8.1 Update 1 Disk Usage 100%

    - by Gookjin Jeong
    Background Information / Computer Specs I have a 14-inch Samsung Series 5 Ultra. Core i5 CPU, 750GB HDD, 8GB RAM, Intel HD Graphics 4000. I've had the computer for about 1.5 years with no major problems. Problem The issue appeared at the beginning of April this year, when I updated the OS to Windows 8.1 Update 1 (not from 8 to 8.1). After being on continually (except for at night, when I put it on sleep mode) for about 48 hours, the disk usage as seen by Task Manager hits 100%. When this happens, everything from opening/closing applications to typing and even bringing up the start screen by pressing the Windows key becomes extremely slow. The only way to make the disk usage decrease is to restart the computer. Then the problem repeats. I've used my current laptop (as well as my previous laptops) this way -- putting it on sleep mode at night and restarting it only when Windows needs to install updates -- for a long time. So I know the 100% disk usage is not due to the way I use the computer. The thing that causes the spike varies. Sometimes it's System, sometimes it's one of the various applications I installed (e.g. Chrome, Evernote, Spotify, Wunderlist, iTunes, etc.), and sometimes it's Antimalware Service Executable, etc. Tried Solutions I think I tried almost every solution out there for this problem: Running the check disk command (chkdsk /b /f /v /scan c:) from Admin Command Prompt Running Windows Memory Diagnostic Disabling Superfetch and Windows Search from services.msc Running "Fix problems with Windows Update" from Control Panel -- Troubleshooting Updating and rolling back the graphics driver (Intel HD 4000) Disabling "Use hardware acceleration when available" from Chrome settings Disabling Intel Rapid Storage Technology Running the SFC /SCANNOW command as recommended here Running a quick scan & a full scan from Windows Defender (no threats found) Taking the hard drive out and putting it back Refreshing the computer, from the Update and recovery -- Recovery option in Windows settings NONE of the above worked for me. I was about to give up but then noticed that one of the main culprits of the disk usage spike, as shown in the "Disk Activity" section of the Resource Monitor, was C:\System (pagefile.sys). I googled around and found that one of the recommended solutions was to disable pagefile. I then went to **Control Panel -- System and Security -- System -- Advanced system settings -- Advanced tab -- Performance settings -- Advanced tab -- "Change" under Virtual memory and discovered that the number for "Currently allocated" at the bottom was 1280MB, although the number for "Recommended" was 4533MB. I immediately changed it to 4533MB and checked my family members' computers to see what the numbers were like. All of theirs had a currently allocated space that was only slightly smaller than the recommended space. See screenshot below: This might fix the problem. I'll have to wait a couple more days.But if it doesn't, what in the world should I do next? I'm guessing the hard drive isn't failing because This computer is less than 2 years old; and Speccy says that the status of the HDD is good. Update 5/27/2014 The "4533MB" solution did not work. I had to reboot the computer about 30 minutes ago because the disk usage again hit 100%. When I opened Resource Monitor the C:\System (pagefile.sys) again was shown to be the culprit. I have now disabled pagefile entirely via the same window shown above in the screenshot. The number for "currently allocated" is now 0MB. Will update again in a couple days, or if the problem occurs again, whichever comes sooner.

    Read the article

  • migrating storage to a different controller

    - by bellocarico
    Hello, I've just purcheased a couple of adaptec controller (2405/5405) for my ESXi 4.0 U1 servers. Currently ESXi and a couple of VMs are hosted on single sata boot disk connected to a nvidia on board non-RAID controller. I know that it's possible to migrate from single disk to RAID 1 with adaptec and I'm pleased with that, but I'm not sure if ESXi has already the right drivers installed/loaded for this controller. Is there any way I can check this? Is ESXi clever enough to recognize the new hardware and load the right module? Thanks

    Read the article

  • Mac failing (failed?) hard drive - is all hope lost?

    - by Daniel
    It's a 500 GB Seagate laptop hard drive that came with my Macbook Pro. Apple partition format. Already replaced and now have it external, connected via SATA/USB adapter. Trying to get just a few files that I worked on while out of town when it crashed (and thus did not have my time machine backup drive). Drive will not mount, but OS X Disk Utility detects it and can read the capacity, model number, and even the name of the partition, which leads me to believe all hope may not be lost. Failed attempts so far: Disk Utility verify+repair says drive cannot be repaired and that I should back up immediately (lovely) Disk Warrior says it cannot rebuild the directory due to hardware failure Data Rescue quick & deep scans immediately failed PhotoRec says "error reading sector" for every sector (at least for the few minutes I let it run before closing it to explore other options) What else can I try here? Again, I'm just looking for a few, small files (python scripts to be specific) - not a full recovery.

    Read the article

  • slow disk writes between host and guest

    - by Jure1873
    I've got a ubuntu (server kernel) on a amd x4, 4gb ram, 2x seagate sata 1 tb disks for testing virtual machines and the write performance is very slow. The two disks are in a software raid1 array, one small boot ext3 partition, 10gb system partition and the rest is a xfs partition (about 980) gb for data (virtual machines). If I'm copying files from the virtual machine to the host with rsync or scp the copy frequently stalls or goes at about 1mb/s. What's wrong? I've tried disabling barriers on xfs, increased logbufs, allocsize, but it seems nothing helps. The strange thing is that await (for example during copying) for sda is usually under 100, while for sdb is around 400. Any ideas on what could be wrong / what could I do to improve this setup?

    Read the article

< Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >