Search Results

Search found 2130 results on 86 pages for 'swap'.

Page 76/86 | < Previous Page | 72 73 74 75 76 77 78 79 80 81 82 83  | Next Page >

  • Ubuntu 12.04 boot degraded raid

    - by beacon_bonanza
    I've installed Ubuntu 12.04.1 in a new server and set up the 4 hard drives with 3 RAID 1 devices, the configuration is such that the first two drives have md0 (swap space) and md1 (/) with the third and fourth drives having md2 (/var). I've been testing the operation under a drive failure and found that the system boots fine if I remove disk two but if I remove disk one then the system gets to grub and then just restarts. I'm confused as to why grub appears to be loading properly from disk two but then the boot fails. I've tried to copy the MBR from disk 1 to 2: dd if=/dev/sda of=/dev/sdb bs=512 count=1 but this didn't make a difference. Any ideas how to get it to boot from just the second disk? fdisk -l Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000ccfa5 Device Boot Start End Blocks Id System /dev/sda1 2048 31250431 15624192 fd Linux RAID autodetect /dev/sda2 * 31250432 3907028991 1937889280 fd Linux RAID autodetect Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000ccfa5 Device Boot Start End Blocks Id System /dev/sdb1 2048 31250431 15624192 fd Linux RAID autodetect /dev/sdb2 * 31250432 3907028991 1937889280 fd Linux RAID autodetect Disk /dev/sdd: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00035b05 Device Boot Start End Blocks Id System /dev/sdd1 2048 3907028991 1953513472 fd Linux RAID autodetect Disk /dev/sdc: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000c73aa Device Boot Start End Blocks Id System /dev/sdc1 2048 3907028991 1953513472 fd Linux RAID autodetect Disk /dev/md1: 1984.3 GB, 1984264208384 bytes 2 heads, 4 sectors/track, 484439504 cylinders, total 3875516032 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md2: 2000.3 GB, 2000263380992 bytes 2 heads, 4 sectors/track, 488345552 cylinders, total 3906764416 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0: 16.0 GB, 15990652928 bytes 2 heads, 4 sectors/track, 3903968 cylinders, total 31231744 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000

    Read the article

  • Suggestions for sharing and using data between Ubuntu and Windows 7 dual boot

    - by wizjany
    Note: TL;DR, scroll to bottom for summary. I recently set up my computer for a dual boot between Ubuntu 9.10 and Windows 7. My current drive setup is as follows. | A1 | A2 | | B1 | B2 | B3 | A1: 100 mb, windows 7 "System Reserved" boot partition A2: 230 gb, data section, this one needs to be shared between the operating systems B1: 125 gb, windows 7 OS B2: 123 gb, ubuntu OS B3: 2gb, linux swap space Pretty much i want to have my documents, music, pictures, videos, etc accessible from both operating systems. My first attempt involved making the data (a2) partition NTFS, and moving my home folder from ubuntu to the data partition. However, as I read NTFS does not work nice with permission, and it messed up my home folder. My next idea is one of the following: 1) format the data partition to ext2/3/4 and move my home folder from linux there, and get a driver to read ext partitions in windows 7. The problem with that is that most of the ext drivers/software are not compatible with windows 7 or do not integrate with windows explorer (I really don't want to open a separate software window just to access my data, plus it's probably not compatible with other software.) http://www.fs-driver.org/ looks promising, but I'm not sure how it works with ext4 and windows 7 (not officially supported, when trying in vista compatibility mode, it tells me I need to format the ext drive to use it). My next idea, 2) keep the home folder in ubuntu where it is, but create symlinks for the Documents, Music, etc folders to an NTFS formatted Data (A2) partition, and add those locations to the windows 7 libraries. I'm not totally sure how the permissions would work out, but it should be fine since it's only the documents, music, etc and not the important config files in the rest of /home/user/. Correct me if I'm wrong. Currently, symlinks is my best idea, although i'm not sure how it will work. Any suggestions, additions to my ideas, links, pointers, whatever would be greatly appreciated. Even if it means i should reformat both my drives and repartition (2 250gb drives if you want to suggest a setup for that), I won't be too opposed if that's the best suggestion (I've gone through the format/install/format/reinstall process 5 times over the past 3 days, once more won't hurt me). TL;DR, summary: I have two hard drives. One is partitioned for Ubuntu and Windows 7, the second one I want accessible to both operating systems to store documents, music, pictures, videos, etc. Suggestions on how to set up the data drive please =) P.S. bonus if I can get an apache server document root folder working between the two OS's as well (permissions could become very complicated, so don't worry too much about that) P.P.S. Related question, but data viewing is one way: http://superuser.com/questions/84586/partition-scheme-and-size-for-dual-boot-windows-7-and-ubuntu-9-10-with-separate-p

    Read the article

  • Safer RAID5 rebuilds using partially failed disks?

    - by arcticmac
    There have been lots of articles posted recently about how RAID5 is dangerous because of long resilver times, and in particular because of increasing chances of encountering a URE during the resilver. Obviously this is a significant concern. However, it seems that in many cases of interest (as long as you're keeping some kind of eye on your disks), when it comes time to rebuild the array, the disk that I'm replacing is still mostly readable. If you try to explain this predicament to the average layperson, they are typically very confused as to why you have two almost completely functional disks but can't produce one working array. It seems to me that there ought to be some way to take advantage of this to make rebuilds safer, as long as I'm willing to have the RAID5 be read-only for a couple of days while it rebuilds. Conceptually, what I have in mind looks something like this: When a disk fails, immediately take the RAID5 offline or mount it read-only Attach a new disk (either in a spare bay, or externally via eSATA) and begin rebuilding it to replace the failed one. If known, perhaps start with the stripes in which the failure occurred, to minimize the chances of losing those if another disk fails. In the event that a second disk experiences a URE or other failure during the rebuild, try to source that data from the disk that is being replaced. Presumably if this happens, more rebuilding would be necessary. When complete, shut down the server, swap the replacement drive into the original bay if desired, and bring the array back up. Obviously such a process would not be appropriate for applications where uptime is critical or data loss cannot be tolerated, but it seems to me that this could help considerably to improve the reliability of RAID5. I assume that there's not a good way to implement a recovery like this at present, given that I haven't seen any indication of tools that are designed to do this, and that it seems like it would be rather obtuse to work out manually. Are there also technical issues with it that I haven't thought of (I'm still fairly new to RAID stuff)? Any thoughts on how hard something like this would be to implement (e.g. in linux md raid)?

    Read the article

  • Preinstalled Windows 8 and Linux UEFI dual boot on a laptop

    - by itchy355
    I am trying to set up Windows 8 and Arch Linux on a new Sony Vaio E14 with preinstalled windows 8. So far: installed W8 to my new SSD (switched for the original HDD) using Recovery Media shrunk the W8 partition, deleted recovery partition, disabled swap confirmed W8 booting just fine On to Arch: disabled Secure Boot in bios confirmed W8 booting just fine Booted Arch off the CD and installed everything to 4th and 5th partition set up rEFInd for EFIstub kernel bootloader After that it got worse. I was unable to boot anything else than Windows 8 (although I was glad that they at least kept working just fine). Tried: creating EFI\refind\ and putting the .efi there (as per Arch manual overwriting EFI\boot\bootx64.efi overwriting EFI\Microsoft\Boot\bootmgr.efi overwriting EFI\Microsoft\Boot\bootmgfw.efi --- YAY rEFInd shown up! So far, so good. I've kept the whole W8 Boot\ directory in EFI\windows8 and set up a boot menuentry for it; and it booted just fine. But, upon restart, everything was wrong -- 'Operating system not found' instead of any bootloader (refind or w8). Booted back into Arch using the live CD to find out that the EFI partition had erroneous FAT table. fsck.vfat fixed it, and I've found that EFI\Microsoft\Boot was back to it's original state (all refind files deleted and replaced with W8 bootloaders). I've overwritten them again and got back to rEFInd showing up correctly and Arch being perfectly bootable. After that I've tried only renaming EFI\Microsoft\Boot\bootmgfw.efi to bootmgfw.001.efi (then copying refind's .efi to bootmgfw.efi and keeping EVERY OTHER file as it was), but with exactly the same result. Tried marking the GPT EFI partition as read-only, same result. Now I'm kinda out of luck. Arch boots fine, so does W8 but it destroys the EFI partition in the process. Thanks for any ideas, Googling brought me this far and I can't find any better. PS -- windows 8 MAYBE destroys the partition upon shutdown -- when I order a shutdown in W8, it takes unusually long (about half a minute instead of ~5 seconds). So in theory I could solve this by hard-resetting the laptop instead of a normal shutdown, but that's just not nice.

    Read the article

  • Postmaster uses excessive CPU and Disk Writes

    - by wolfcastle
    using PostgreSQL 9.1.2 I'm seeing excessive CPU usage and large amounts of writes to disk from postmaster tasks. This happens even while my application is doing almost nothing (10s of inserts per MINUTE). There are a reasonable number of connections open however. I've been trying to determine what in my application is causing this. I'm pretty newb with postgresql, and haven't gotten anywhere so far. I've turned on some logging options in my config file, and looked at connections in the pg_stat_activity table, but they are all idle. Yet each connection consumes ~ 50% CPU, and is writing ~15M/s to disk (reading nothing). I'm basically using the stock postgresql.conf with very little tweaks. I'd appreciate any advice or pointers on what I can do to track this down. Here is a sample of what top/iotop is showing me: Cpu(s): 18.9%us, 14.4%sy, 0.0%ni, 53.4%id, 11.8%wa, 0.0%hi, 1.5%si, 0.0%st Mem: 32865916k total, 7263720k used, 25602196k free, 575608k buffers Swap: 16777208k total, 0k used, 16777208k free, 4464212k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 17057 postgres 20 0 236m 33m 13m R 45.0 0.1 73:48.78 postmaster 17188 postgres 20 0 219m 15m 11m R 42.3 0.0 61:45.57 postmaster 17963 postgres 20 0 219m 16m 11m R 42.3 0.1 27:15.01 postmaster 17084 postgres 20 0 219m 15m 11m S 41.7 0.0 63:13.64 postmaster 17964 postgres 20 0 219m 17m 12m R 41.7 0.1 27:23.28 postmaster 18688 postgres 20 0 219m 15m 11m R 41.3 0.0 63:46.81 postmaster 17088 postgres 20 0 226m 24m 12m R 41.0 0.1 64:39.63 postmaster 24767 postgres 20 0 219m 17m 12m R 41.0 0.1 24:39.24 postmaster 18660 postgres 20 0 219m 14m 9.9m S 40.7 0.0 60:51.52 postmaster 18664 postgres 20 0 218m 15m 11m S 40.7 0.0 61:39.61 postmaster 17962 postgres 20 0 222m 19m 11m S 40.3 0.1 11:48.79 postmaster 18671 postgres 20 0 219m 14m 9m S 39.4 0.0 60:53.21 postmaster 26168 postgres 20 0 219m 15m 10m S 38.4 0.0 59:04.55 postmaster Total DISK READ: 0.00 B/s | Total DISK WRITE: 195.97 M/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO> COMMAND 17962 be/4 postgres 0.00 B/s 14.83 M/s 0.00 % 0.25 % postgres: aggw aggw [local] idle 17084 be/4 postgres 0.00 B/s 15.53 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 17963 be/4 postgres 0.00 B/s 15.00 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 17188 be/4 postgres 0.00 B/s 14.80 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 17964 be/4 postgres 0.00 B/s 15.50 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 18664 be/4 postgres 0.00 B/s 15.13 M/s 0.00 % 0.23 % postgres: aggw aggw [local] idle 17088 be/4 postgres 0.00 B/s 14.71 M/s 0.00 % 0.13 % postgres: aggw aggw [local] idle 18688 be/4 postgres 0.00 B/s 14.72 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 24767 be/4 postgres 0.00 B/s 14.93 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 18671 be/4 postgres 0.00 B/s 16.14 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 17057 be/4 postgres 0.00 B/s 13.58 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 26168 be/4 postgres 0.00 B/s 15.50 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 18660 be/4 postgres 0.00 B/s 15.85 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle

    Read the article

  • Download - Upload is too slow on Centos

    - by Mehdi
    My download/upload in server and out of server is too slow (around 50 KB/s !) ! Did I miss some configuration ? Some information: CentOS release 6.3 uptime load average: 0.17, 0.32, 0.37 Memory free -m total used free shared buffers cached Mem: 24009 21988 2021 0 806 18098 -/+ buffers/cache: 3083 20926 Swap: 4095 28 4067 lshw -C network *-network description: Ethernet interface product: 82574L Gigabit Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 00 serial: 00:25:90:70:17:4a size: 100MB/s capacity: 1GB/s width: 32 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=off broadcast=yes driver=e1000e driverversion=1.9.5-k duplex=full firmware=2.1-2 ip=108.175.8.123 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:16 memory:fb900000-fb91ffff ioport:e000(size=32) memory:fb920000-fb923fff ethtool ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off MDI-X: off Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000001 (1) Link detected: yes dmesg |grep e1000e dmesg |grep e1000e e1000e: Intel(R) PRO/1000 Network Driver - 1.9.5-k e1000e: Copyright(c) 1999 - 2012 Intel Corporation. e1000e 0000:02:00.0: Disabling ASPM L0s e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 e1000e 0000:02:00.0: setting latency timer to 64 e1000e 0000:02:00.0: irq 33 for MSI/MSI-X e1000e 0000:02:00.0: irq 34 for MSI/MSI-X e1000e 0000:02:00.0: irq 35 for MSI/MSI-X e1000e 0000:02:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:70:17:4a e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: Unsupported Speed/Duplex configuration e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: Disabling ASPM L1 e1000e 0000:02:00.0: eth0: changing MTU from 1500 to 9000 e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO

    Read the article

  • Kickstart based installation of RHEL 6.4 from USB

    - by Peter
    I want to setup some brand new servers with RHEL 6.4. Servers do not have DVD, so, I have to use USB for the installation. I already have a custom ISO with a kickstart file that I use on servers with DVD flawlessly. I used iso2usb to move the ISO t? my USB. When I boot from the USB, the ks file is found, anaconda starts, but then stops with the following error: "The installation source given by device ['sda1'] could not be found. Please check your parameters and try again" Notes: The USB IS the sda. My custom ISO file is renamed to linux.iso from iso2usb and it is present in the root directory of the USB. Kickstart file has the following entry: harddrive --partition=sda1 --dir=/ Please help me to automate the installation with kickstart. Edit 1: This the anaconda.log file: 09:01:57,029 INFO : no /etc/zfcp.conf; not configuring zfcp 09:01:57,259 INFO : created new libuser.conf at /tmp/libuser.4rAbps with instPath="/mnt/sysimage" 09:01:57,259 INFO : anaconda called with cmdline = ['/usr/bin/anaconda', '--stage2', 'hd:sda1:///images/install.img', '--dlabel', '--kickstart', '/tmp/ks.cfg', '--graphical', '--selinux', '--lang', 'en_US.UTF-8', '--keymap', 'us', '--repo', 'hd:sda1:/'] 09:01:57,260 INFO : Display mode = g 09:01:57,260 INFO : Default encoding = utf-8 09:01:59,444 DEBUG : X server has signalled a successful start. 09:01:59,446 INFO : Starting window manager, pid 1345. 09:01:59,537 INFO : Starting graphical installation. 09:01:59,741 INFO : Detected 7968M of memory 09:01:59,741 INFO : Swap attempt of 7968M 09:02:00,840 INFO : ISCSID is /usr/sbin/iscsid 09:02:00,840 INFO : no initiator set Edit 2: This is the part of anaconda log that indicates that it found the USB etc: 09:01:47,918 INFO : starting STEP_STAGE2 09:01:47,918 INFO : partition is sda1, dir is //images/install.img 09:01:47,918 INFO : mounting device sda1 for hard drive install 09:01:48,005 INFO : Path to stage2 image is /mnt/isodir///images/install.img 09:01:54,214 INFO : mounted loopback device /mnt/runtime on /dev/loop0 as /tmp/install.img 09:01:54,214 INFO : Looking for updates for HD in /mnt/isodir///images/updates.img 09:01:54,214 INFO : Looking for product for HD in /mnt/isodir///images/product.img 09:01:54,227 INFO : got stage2 at url hd:sda1:///images/install.img 09:01:54,254 INFO : Loading SELinux policy 09:01:54,700 INFO : getting ready to spawn shell now 09:01:54,975 INFO : Running anaconda script /usr/bin/anaconda 09:01:56,882 INFO : _Fedora is the highest priority installclass, using it 09:01:56,921 INFO : Running kickstart %%pre script(s) 09:01:56,922 WARNING : '/bin/sh' specified as full path 09:01:56,926 INFO : All kickstart %%pre script(s) have been run

    Read the article

  • Trouble setting up PATH for Java on Debian

    - by milkmansrevenge
    I am trying to get Oracle Java 7 update 3 working correctly on Debian 6. I have downloaded and set up the files in /usr/java/jre1.7.0_03. I have also set the following two lines at the end of /etc/bash.bashrc: export JAVA_HOME=/usr/java/jre1.7.0_03 export PATH=$PATH:$JAVA_HOME/bin Logging in as other users and root is fine, Java can be found: chris@mc:~$ java -version java version "1.7.0_03" Java(TM) SE Runtime Environment (build 1.7.0_03-b04) Java HotSpot(TM) 64-Bit Server VM (build 22.1-b02, mixed mode) However there are two cases where Java cannot be found as detailed below. Note that both of these worked fine when I have previously installed OpenJDK Java 6 via aptitude, but I need Oracle Java 7 for various reasons. Most importantly, I cannot run commands as another user via su, despite the PATH showing that Java should be present. The user was created with adduser chris root@mc:~# su chris -c "echo $PATH" /usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/java/jre1.7.0_03/bin:/bin root@mc:~# su chris -c "java -version" bash: java: command not found root@mc:~# su chris -c "/usr/java/jre1.7.0_03/bin/java -version" java version "1.7.0_03" ... How can it be in the PATH but not be found? Update 05/04/2012: explained by Daniel, to do with it being a non-interactive shell so files such as /etc/profile and /etc/bash.bashrc are not executed. Doing a full swap to that user and running Java works: root@mc:~# su chris chris@mc:/root$ java -version java version "1.7.0_03" ... I run a script on start up which exhibits similar but slightly different problems. The script is located in /etc/init.d/start-mystuff.sh and calls a jar: #!/bin/bash # /etc/init.d/start-mystuff.sh java -jar /opt/Mars.jar I can confirm that the script runs on start up and the exit code is 127, which indicates command not found. Inserting a line to print/save the PATH shows that it is: /sbin:/usr/sbin:/bin:/usr/bin This second problem isn't as important because I can just point directly to the Java executable in the script, but I am still curious! I have tried setting the full PATH and JAVA_HOME explicitly in /etc/environment which didn't help. I have also tried setting them in /etc/profile which doesn't seem to help either. I have tried logging in and out again after setting PATH in the various locations (duh!). Anyway, long post for what will probably have a simple one line solution :( Any help with this would be greatly appreciated, I have spent far too long trying to fix it by myself. Motivation The first problem may seem obscure but in my system I have users that are not allowed SSH access yet I still want to run processes as them. I have a ton of scripts operating in this way and don't want to have to change them all.

    Read the article

  • Easiest way to replace preinstalled Windows 8 with new hard drive with Windows 7

    - by Andrew
    There are all kinds of questions and answers relevant moving Windows 8 to a new hard drive. I'm not seeing anything quite applicable to my situation. I have a new, unopened, unbooted notebook with pre-installed Windows 8. I will be replacing the hard drive before ever booting, unless that is not possible for some reason. I want to "downgrade" to Windows 7 Pro, and I want a clean installation. To do so legitimately, I apparently either need to: Upgrade Windows 8 to Windows 8 Pro using Windows 8 Pro Pack, then downgrade; or Just install a newly-licensed copy of Windows 7 Pro. (Let me know if I've missed an option.) Installation media is likely not a problem, though if I need something vendor-specific that I cannot otherwise download, that could present an issue (Asus notebook, if that matters). If I could, I would just buy the Pro Pack upgrade, swap the hard drive (without ever booting), then install Windows 7 Pro directly on the new hard drive, using the Pro Pack key for activation. Will this work? Are there any activation issues? Edited to clarify, as some comments and answers indicate confusion: Here is, ideally, what I want to do: Before ever powering on the notebook, remove the current hard drive. Replace this hard drive with a new, blank hard drive. Install a clean copy of Windows 7 Pro on this new, blank hard drive. Unless I have no choice to accomplish the end result (a clean install of Win7 Pro on the newly-installed, previously-blank hard drive), I am not wanting to: Install Windows 7 "over" the current Windows 8 install (after upgrading to Win8 Pro). That would involve using the currenly-installed hard drive. I want to use a new, different hard drive. Copy the Win8 install to the new hard drive, then install Windows 7 "over" that installation. Install Windows 7 "over" the current Windows 8 install (after upgrading to Win8 Pro), then copy the installation to the new hard drive. If I have to use one of those three options, I will, but only if there is no other choice. Please note that this question is not about licensing: I will purchase the necessary license(s) to accomplish this procedure legally (apparently either Win8 Pro Pack or Win7 Pro -- the former currently appears less expensive).

    Read the article

  • PowerDNS CNAME with multiple A records produces unexpected results

    - by bwight
    This problem from what i can tell is isolated to PowerDNS. The servers are running two packages pdns-static-3.0.1-1.i386.rpm and pdns-recursor-3.3-1.i386.rpm on the most recent version of Amazon Linux. The amazon ec2 loadbalancers are assigned a CNAME with multiple hosts. Below is an example of the actual behavior. Notice how the hosts are always in the same order. [root@localhost ~]# host cache.domain.com cache.domain.com is an alias for xxxxx.us-east-1.elb.amazonaws.com. xxxxx.us-east-1.elb.amazonaws.com has address aaa.aaa.aaa.aaa xxxxx.us-east-1.elb.amazonaws.com has address bbb.bbb.bbb.bbb [root@localhost ~]# host cache.domain.com cache.domain.com is an alias for xxxxx.us-east-1.elb.amazonaws.com. xxxxx.us-east-1.elb.amazonaws.com has address aaa.aaa.aaa.aaa xxxxx.us-east-1.elb.amazonaws.com has address bbb.bbb.bbb.bbb [root@localhost ~]# host cache.domain.com cache.domain.com is an alias for xxxxx.us-east-1.elb.amazonaws.com. xxxxx.us-east-1.elb.amazonaws.com has address aaa.aaa.aaa.aaa xxxxx.us-east-1.elb.amazonaws.com has address bbb.bbb.bbb.bbb Expected behavior is round robin for the hosts [root@localhost ~]# host cache.domain.com cache.domain.com is an alias for xxxxx.us-east-1.elb.amazonaws.com. xxxxx.us-east-1.elb.amazonaws.com has address aaa.aaa.aaa.aaa xxxxx.us-east-1.elb.amazonaws.com has address bbb.bbb.bbb.bbb [root@localhost ~]# host cache.domain.com cache.domain.com is an alias for xxxxx.us-east-1.elb.amazonaws.com. xxxxx.us-east-1.elb.amazonaws.com has address bbb.bbb.bbb.bbb xxxxx.us-east-1.elb.amazonaws.com has address aaa.aaa.aaa.aaa [root@localhost ~]# host cache.domain.com cache.domain.com is an alias for xxxxx.us-east-1.elb.amazonaws.com. xxxxx.us-east-1.elb.amazonaws.com has address aaa.aaa.aaa.aaa xxxxx.us-east-1.elb.amazonaws.com has address bbb.bbb.bbb.bbb The addresses eventually do swap but it seems to be on a 30 minute cache timer changing the TTL of the record doesn't appear to affect anything. It appears as though the resolver has a cache of the response. This adversely affects my application because all of the load is only being sent to one of the loadbalancers (Availability Zones) so if I have servers in two zones then only one zone is under load at a time. Do you know how I can fix this so that each time the host is resolved the order of the addresses is alternating.

    Read the article

  • Windows Setup could not configure Windows to run on this computer's hardware

    - by Hello71
    The whole installation goes smoothly up to the point of "Completing installation ...". The monitor changes resolution, after which a standard dialog box pops up saying Windows Setup could not configure Windows to run on this computer's hardware Then, in a few seconds, the whole machine powers down. Trying to restart produces the message: STOP: c000021a {Fatal System Error} 0x00000000 (0xc0000001 0x00100448) OR it boots into Setup and comes up with the message: Windows Setup encountered an unexpected error... (This is not the actual error, just paraphrasing) I tried using the OEM restore instead of a regular install, but it fails with the same error. (Even though it worked before...) General specs: HP Pavilion Elite e9262f Intel Core i5-750 Processor ATI Radeon HD 4650 Hitachi HDT721010SLA360 ATA Device 6GB DDR3 RAM SuperMulti DVD Burner with LightScribe Some built-in Wi-Fi module http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01916917 I've tried disconnecting the wireless card and disabling the built-in Ethernet and Firewire via the BIOS, and replacing the wireless keyboard and mouse with wired USB ones. Didn't work. I've also tried changing the SATA controller settings in the BIOS to RAID, AHCI, and IDE, reinstalling each time I changed. Still not working. I think the reason why it is showing the Fatal System Error is because it didn't finish installing before it errored out and shut down, so the system is left in an inconsistent state. I've tried 3 different copies (including the OEM restore) of Windows 7 now, and they're all failing at the same point, with the same error message. I've tried to install Windows 7 maybe 10 times already, with the exact same error message at the exact same location. Hm... Interestingly, the 32-bit version of Windows 7 works, but the 64-bit version doesn't. Perhaps it was a badly burned disk? Reburning the 64-bit version still comes up with the same error. Here's a picture of the side of the case that clearly says it came with Windows 7 64-bit, along with the model number and CPU. sudo fdisk -l: Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009896f Device Boot Start End Blocks Id System /dev/sda1 * 1 13 104391 7 HPFS/NTFS /dev/sda2 14 94119 755906445 7 HPFS/NTFS /dev/sda3 119922 121602 13492224 7 HPFS/NTFS /dev/sda4 94120 119922 207257740+ 5 Extended /dev/sda5 119527 119922 3170769 82 Linux swap / Solaris /dev/sda6 107174 119526 99225441 83 Linux /dev/sda7 94120 107173 104856192 7 HPFS/NTFS Partition table entries are not in disk order

    Read the article

  • Volume group disappeared, LVs still available

    - by Ben
    I've run into an issue with my KVM host which runs VMs on a LVM volume. As of last night the logical volumes are no longer seen as such (I can't create snapshots of them even though I have been for months now). Running any scans all result in nothing being found: [root@apollo ~]# pvscan No matching physical volumes found [root@apollo ~]# vgscan Reading all physical volumes. This may take a while... No volume groups found root@apollo ~]# lvscan No volume groups found If I try restoring the VG conf backup from /etc/lvm/backups/vg0 I get the following error: [root@apollo ~]# vgcfgrestore -f /etc/lvm/backup/vg0 vg0 Couldn't find device with uuid 20zG25-H8MU-UQPf-u0hD-NftW-ngsC-mG63dt. Cannot restore Volume Group vg0 with 1 PVs marked as missing. Restore failed. /etc/lvm/backups/vg0 has the following for the physical volume: physical_volumes { pv0 { id = "20zG25-H8MU-UQPf-u0hD-NftW-ngsC-mG63dt" device = "/dev/sda5" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 4292870143 # 1.99902 Terabytes pe_start = 384 pe_count = 524031 # 1.99902 Terabytes } } fdisk -l /dev/sda shows the following: [root@apollo ~]# fdisk -l /dev/sda Disk /dev/sda: 6000.1 GB, 6000069312512 bytes 64 heads, 32 sectors/track, 5722112 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000188b7 Device Boot Start End Blocks Id System /dev/sda1 2 32768 33553408 82 Linux swap / Solaris /dev/sda2 32769 33280 524288 83 Linux /dev/sda3 33281 1081856 1073741824 83 Linux /dev/sda4 1081857 3177984 2146435072 85 Linux extended /dev/sda5 1081857 3177984 2146435071+ 8e Linux LVM The server is running a 4 disk HW RAID10 which seems perfectly healthy according to megacli and smartd. The only odd message in /var/log/messages is the following which shows up every couple of hours: Jun 10 09:41:57 apollo udevd[527]: failed to create queue file: No space left on device Output of df -h [root@apollo ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda3 1016G 119G 847G 13% / /dev/sda2 508M 67M 416M 14% /boot Does anyone have any ideas what to do next? The VMs are all running fine at the moment apart from not being able to snapshot them. Updated with extra info It's not a lack of inodes: [root@apollo ~]# df -i Filesystem Inodes IUsed IFree IUse% Mounted on /dev/sda3 67108864 48066 67060798 1% / /dev/sda2 32768 47 32721 1% /boot pvs, vgs & lvs either output nothing or "No volume groups found".

    Read the article

  • Disk IO causing high load on Xen/CentOS guest

    - by Peter Lindqvist
    I'm having serious issues with a xen based server, this is on the guest partition. It's a paravirtualized CentOS 5.5. The following numbers are taken from top while copying a large file over the network. If i copy the file another time the speed decreases in relation to load average. So the second time it's half the speed of the first time. It needs some time to cool off after this. Load average slowly decreases until it's once again usable. ls / takes about 30 seconds. top - 13:26:44 up 13 days, 21:44, 2 users, load average: 7.03, 5.08, 3.15 Tasks: 134 total, 2 running, 132 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.1%sy, 0.0%ni, 25.3%id, 74.5%wa, 0.0%hi, 0.0%si, 0.1%st Mem: 1048752k total, 1041460k used, 7292k free, 3116k buffers Swap: 2129912k total, 40k used, 2129872k free, 904740k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1506 root 10 -5 0 0 0 S 0.3 0.0 0:03.94 cifsd 1 root 15 0 2172 644 556 S 0.0 0.1 0:00.08 init Meanwhile the host is ~0.5 load avg and steady over time. ~50% wait Server hardware is dual xeon, 3gb ram, 170gb scsi 320 10k rpm, and shouldn't have any problems with copying files over the network. disk = [ "tap:aio:/vm/dev01.img,xvda,w" ] I also get these in the log INFO: task syslogd:1350 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. syslogd D 00062E4F 2208 1350 1 1353 1312 (NOTLB) c0ef0ed0 00000286 6e71a411 00062e4f c0ef0f18 00000009 c0f20000 6e738bfd 00062e4f 0001e7ec c0f2010c c181a724 c1abd200 00000000 ffffffff c0ef0ecc c041a180 00000000 c0ef0ed8 c03d6a50 00000000 00000000 c03d6a00 00000000 Call Trace: [<c041a180>] __wake_up+0x2a/0x3d [<ee06a1ea>] log_wait_commit+0x80/0xc7 [jbd] [<c043128b>] autoremove_wake_function+0x0/0x2d [<ee065661>] journal_stop+0x195/0x1ba [jbd] [<c0490a32>] __writeback_single_inode+0x1a3/0x2af [<c04568ea>] do_writepages+0x2b/0x32 [<c045239b>] __filemap_fdatawrite_range+0x66/0x72 [<c04910ce>] sync_inode+0x19/0x24 [<ee09b007>] ext3_sync_file+0xaf/0xc4 [ext3] [<c047426f>] do_fsync+0x41/0x83 [<c04742ce>] __do_fsync+0x1d/0x2b [<c0405413>] syscall_call+0x7/0xb ======================= I have tried disabling irqbalanced as suggested here but it does not seem to make any difference.

    Read the article

  • Why does Ubuntu 9.10 hang during boot at "Booting processor 1 APIC 0x1 ip 0x6000"?

    - by BraeburnDev
    I recently installed a new copy of Ubuntu 9.10 (Kernel 2.6.31-14) on to my Hp Pavilion dv6t, so I can setup a Linux development environment. The install went flawlessly and I proceeded with Ubuntu's udate manager's long list of updates (292 in all). I also setup a swap file and activated a Nvidia 185 driver for the Nvidia 260m GPU on the machine. After all this was done I restarted the computer and booted into Ubuntu this time with a newer 2.6.31-19 Kernel which was installed from the update manager. During booth the computer hung at this point: Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013136] Performance Counters: Nehalem/Corei7 events, Intel PMU driver. Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013141] ... version: 3 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013142] ... bit width: 48 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013144] ... generic counters: 4 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013146] ... value mask: 0000ffffffffffff Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013147] ... max period: 000000007fffffff Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013149] ... fixed-purpose counters: 3 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013151] ... counter mask: 000000070000000f Feb 24 14:23:12 braeburn-laptop kernel: [ 0.015539] ACPI: Core revision 20090521 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.052264] Setting APIC routing to flat Feb 24 14:23:12 braeburn-laptop kernel: [ 0.052639] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.152580] CPU0: Intel(R) Core(TM) i7 CPU Q 720 @ 1.60GHz stepping 05 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.270845] Booting processor 1 APIC 0x1 ip 0x6000 I can post a full kern.log of this boot process if requested. Hopefully this is enough information to go on. I should add that I'm still new to configuring and running a Linux OS although I know enough basic command line usage to do software development. This is my attempt to become more familiar with Linux and manage my own system. I'd like to get some insight on the nature of this system hang, what the problem is and how to resolve it. At this point I can scrap the install if I broke something, but my intuition says this is an issue with the kernel recognizing the correct hardware configuration for my system, or perhaps this is an issue with the APIC drivers managing Nehalem's new power management capabilities? Thanks for looking at this issue and providing feed back.

    Read the article

  • Resizing Partitions on Live RHEL/cPanel Server

    - by Timothy R. Butler
    I've resized many partitions over the years on Linux, Windows and Mac OS X -- but always using a GUI. However, the time has come where the preset partition sizes my data center placed on my server aren't the right sizes and I need to resize a production server's disks. I could fiddle with it and probably do OK, but given that it is a production server, I wanted to get some advice about the right way to do this. I do have KVM over IP access, so if it is best to take the server offline and boot off a rescue partition, I can do that. root [/var/lib/mysql]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.9G 2.1G 7.3G 23% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 99M 77M 18M 82% /boot /dev/sda8 884G 463G 376G 56% /home /dev/sda3 9.9G 8.0G 1.5G 85% /usr /dev/sda5 9.9G 9.1G 308M 97% /var /usr/tmpDSK 2.0G 38M 1.8G 3% /tmp As you can see /var and /usr are quite close to being full and I've actually had to symlink some logs on /usr to directories in /home to balance things out. What I would like to do is to add 6-10 GB each to /usr and /var, presumably taking the space from /home. As I think about how the disk is arranged, the best thought I've come up with is to reduce /home by 16 GB, say, and move /var to the spot freed up, then allocating /var's space to /usr. However, that would put /var at the far end of the disk, which seems less than idea, given that MySQL has all of its data on that partition. I'd love to take the space out of the closer end of /usr, but I assume that would take a very arduous (and perhaps risky) process of moving all of the data in /usr around. I seem to recall having such a process fail for me on a computer in the past. The other option might be to merge / and /usr since / is underutilized, though I'm not sure if that's a good idea. Do you have any suggestions both on the best reallocation plan and the commands to use to accomplish it? UPDATE: I should add -- here's the partition table. There's one unused partition, which, if memory serves, was the original tmp location before I created a tmp image: Name Flags Part Type FS Type [Label] Size (MB) ------------------------------------------------------------------------------ Unusable 1.05* sda1 Boot Primary Linux ext2 106.96* sda2 Primary Linux ext3 10737.42* sda3 Primary Linux ext3 10737.42* sda5 NC Logical Linux ext3 10738.47* sda6 NC Logical Linux swap / Solaris 2148.54* sda7 NC Logical Linux ext3 1074.80* sda8 NC Logical Linux ext3 964098.53*

    Read the article

  • 64-bit linux kernel only seeing 3 of 4GB after upgrade...

    - by Blaine
    Hey everyone. I am running Ubuntu 9.04 64-bit on my macbook. I had 2GB of ram before, and everything ran great. I just upgraded to 2x2GB (4GB), but my system only sees 3GB of it. OS X, which I am dual booting, sees all 4GB. Also, my video performance is incredibly lacking. Before the upgrade my compiz benchmark was full at 80fps, and now it is at 22fps with very choppy window dragging. Has anyone ever heard of this on a 64-bit kernel? I just don't quite understand what could be the issue. 10$ uname -a Linux macbook 2.6.28-15-generic #49-Ubuntu SMP Tue Aug 18 19:25:34 UTC 2009 x86_64 GNU/Linux $ free -m total used free shared buffers cached Mem: 2953 1031 1921 0 114 427 -/+ buffers/cache: 489 2463 Swap: 7812 0 7812 9$ lsmod Module Size Used by i915 77960 2 drm 123232 3 i915 binfmt_misc 18572 1 ppdev 16904 0 btusb 21784 2 bridge 63776 0 stp 11140 1 bridge bnep 22912 2 vboxnetadp 109356 0 vboxnetflt 116972 0 vboxdrv 1721612 1 vboxnetflt uvcvideo 69640 0 compat_ioctl32 18304 1 uvcvideo videodev 45184 2 uvcvideo,compat_ioctl32 v4l1_compat 23940 2 uvcvideo,videodev lp 19588 0 parport 49584 2 ppdev,lp snd_hda_intel 557492 3 snd_pcm_oss 52352 0 snd_mixer_oss 24960 1 snd_pcm_oss snd_pcm 99464 2 snd_hda_intel,snd_pcm_oss arc4 10240 2 snd_seq_dummy 11524 0 ecb 11392 2 snd_seq_oss 41984 0 snd_seq_midi 15744 0 snd_rawmidi 33920 1 snd_seq_midi snd_seq_midi_event 16512 2 snd_seq_oss,snd_seq_midi snd_seq 66272 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event ath9k 310584 0 snd_timer 34064 2 snd_pcm,snd_seq snd_seq_device 16276 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq mac80211 251528 1 ath9k iTCO_wdt 21712 0 iTCO_vendor_support 12420 1 iTCO_wdt joydev 20992 0 video 29204 0 snd 78920 15 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device applesmc 37700 0 output 11648 1 video soundcore 16800 1 snd pcspkr 11136 0 cfg80211 43680 1 mac80211 appletouch 19972 0 isight_firmware 11520 0 input_polldev 12688 1 applesmc intel_agp 39408 1 snd_page_alloc 18704 2 snd_hda_intel,snd_pcm led_class 13064 2 ath9k,applesmc hid_apple 15872 0 usbhid 47040 0 ohci1394 42164 0 ieee1394 108288 1 ohci1394 sky2 63364 0 fbcon 49792 0 tileblit 11264 1 fbcon font 17024 1 fbcon bitblit 14464 1 fbcon softcursor 10368 1 bitblit Some information from dmesg: [ 795.820163] ACPI: EC: GPE storm detected, transactions will use polling mode [ 1762.709516] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 1763.078130] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 2362.760889] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 2416.352084] ACPI: EC: missing confirmations, switch off interrupt mode. [ 3718.721095] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 3719.108914] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 4318.773266] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 9513.813066] CE: hpet increasing min_delta_ns to 15000 nsec [ 9693.815684] npviewer.bin[6736]

    Read the article

  • Why is mount -a not mounting fuse drive properly when executed remotely (via Fabric)?

    - by Jim D
    This is a weird bug and I'm not sure where it's coming from. Here's a quick run down of what I'm doing. I'm trying to mount a FUSE drive to an Amazon EC2 instance running Ubuntu 10.10 using s3fs (FUSE over Amazon). s3fs is compiled from source according to the instructions etc. I've also added an entry to /etc/fstab so that the drive mounts on boot. Here's what /etc/fstab looks like: # /etc/fstab: static file system information. # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 LABEL=uec-rootfs / ext4 defaults 0 0 /dev/sda2 /mnt auto defaults,nobootwait,comment=cloudconfig 0 2 /dev/sda3 none swap sw,comment=cloudconfig 0 0 s3fs#mybucket /mnt/s3/mybucket fuse default_acl=public-read,use_cache=/tmp,allow_other 0 0 So the good news is that this works fine. On reboot the connection mounts correctly. I can also do: $ sudo umount /mnt/s3/mybucket $ sudo mount -a $ mountpoint /mnt/s3/mybucket /mnt/s3/mybucket is a mountpoint Great, right? Well here's the problem. I'm using Fabric to automate the process of building and managing this instance. I noticed I was getting this error message when using Fabric to build s3fs and set up the mount process: mountpoint: /mnt/s3/mybucket: Transport endpoint is not connected I isolated it down the the problem and built a fabric task that reproduces the problem: def remount_s3fs(): sudo("mount -a") Which does: [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] Executing task 'remount_s3fs' [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] sudo: mount -a [And yes, I was sure to unmount it before running this task.] When I check the mount using mountpoint I get: $ mountpoint /mnt/s3/mybucket mountpoint: /mnt/s3/mybucket: Transport endpoint is not connected Done. But if I run sudo mount -a at the command line, it works. Hrm. Here is that fab task output again, this time in full debug mode: [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] Executing task 'remount_s3fs' [ec2-xx-xx-xx-xx.compute-1.amazonaws.com] sudo: sudo -S -p 'sudo password:' /bin/bash -l -c "mount -a" Again, I get that transport endpoint not connected error. I've also tried copying and pasting the exact command run into my ssh session (i.e. sudo -S -p 'sudo password:' /bin/bash -l -c "mount -a") and it works fine. So...that's my problem. Any ideas?

    Read the article

  • load-causing processes disappearing from "top" ps -o pcpu shows bogus numbers

    - by Alec Matusis
    I administer a large number of servers, and I have this problem only with Ubuntu 10.04 LTS: I run a server under normal load (say load average 3.0 on an 8-core server). The "top" command shows processes taking certain % of CPU that cause this load average: say PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 11008 mysql 20 0 25.9g 22g 5496 S 67 76.0 643539:38 mysqld ps -o pcpu,pid -p11008 %CPU PID 53.1 11008 , everything is consistent. The all of the sudden, the process causing the load average disappears from "top", but the process continues to run normally (albeit with a slight performance decrease), and the system load average becomes somewhat higher. The output of ps -o pcpu becomes bogus: # ps -o pcpu,pid -p11008 %CPU PID 317910278 1587 This happened to at least 5 different severs (different brand new IBM System X hardware), each running different software: one httpd 2.2, one mysqld 5.1, and one Twisted Python TCP servers. Each time the kernel was between 2.6.32-32-server and 2.6.32-40-server. I updated some machines to 2.6.32-41-server, and it has not happened on those yet, but the bug is rare (once every 60 days or so). This is from an affected machine: top - 10:39:06 up 73 days, 17:57, 3 users, load average: 6.62, 5.60, 5.34 Tasks: 207 total, 2 running, 205 sleeping, 0 stopped, 0 zombie Cpu(s): 11.4%us, 18.0%sy, 0.0%ni, 66.3%id, 4.3%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 74341464k total, 71985004k used, 2356460k free, 236456k buffers Swap: 3906552k total, 328k used, 3906224k free, 24838212k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 805 root 20 0 0 0 0 S 3 0.0 1493:09 fct0-worker 982 root 20 0 0 0 0 S 1 0.0 111:35.05 fioa-data-groom 914 root 20 0 0 0 0 S 0 0.0 884:42.71 fct1-worker 1068 root 20 0 19364 1496 1060 R 0 0.0 0:00.02 top Nothing causing high load is showing on top, but I have two highly loaded mysqld instances on it, that suddenly show crazy %CPU: #ps -o pcpu,pid,cmd -p1587 %CPU PID CMD 317713124 1587 /nail/encap/mysql-5.1.60/libexec/mysqld and #ps -o pcpu,pid,cmd -p1624 %CPU PID CMD 2802 1624 /nail/encap/mysql-5.1.60/libexec/mysqld Here are the numbers from # cat /proc/1587/stat 1587 (mysqld) S 1212 1088 1088 0 -1 4202752 14307313 0 162 0 85773299069 4611685932654088833 0 0 20 0 52 0 3549 27255418880 5483524 18446744073709551615 4194304 11111617 140733749236976 140733749235984 8858659 0 552967 4102 26345 18446744073709551615 0 0 17 5 0 0 0 0 0 the 14th and 15th numbers according to man proc are supposed to be utime %lu Amount of time that this process has been scheduled in user mode, measured in clock ticks (divide by sysconf(_SC_CLK_TCK). This includes guest time, guest_time (time spent running a virtual CPU, see below), so that applications that are not aware of the guest time field do not lose that time from their calculations. stime %lu Amount of time that this process has been scheduled in kernel mode, measured in clock ticks (divide by sysconf(_SC_CLK_TCK). On a normal server, these numbers are advancing, every time I check the /proc/PID/stat. On a buggy server, these numbers are stuck at a ridiculously high value like 4611685932654088833, and it's not changing. Has anyone encountered this bug?

    Read the article

  • VBA + Polymorphism: Override worksheet functions from 3rd party

    - by phi
    my company makes extensive use of a data provider using a (closed source) VBA plugin. In principal, every query follows follows a certain structure: Fill one cell with a formula, where arguments to the formula specify the query the range of that formula is extended (not an arrray formula!) and cells below/right are filled with data For this to work, however, a user has to have a terminal program installed on the machine, as well as a com-plugin referenced in VBA/Excel. My Problem These Excelsheets are used and extended by multiple users, and not all of them have access to the data provider. While they can open the sheet, it will recalculate and the data will be gone. However, frequent recalculation is required. I would like every user to be able to use the sheets, without executing a very specific set of formulas. Attempts remove the reference on those computers where I do not have terminal access. This generates a NAME error i the cell containing the query (acceptable), but this query overrides parts of the data (not acceptable) If you allow the program to refresh, all data will be gone after a failed query Replace all formulas with the plain-text result in the respective cells (press a button and loop over every cell...). Obviously destroys any refresh-capabilities the querys offer for all subsequent users, so pretty bad, too. A theoretical idea, and I'm not sure how to implement it: Replace the functions offered by the plugin with something that will be called either first (and relay the query through to the original function, if thats available) or instead of the original function (by only deploying the solution on non-terminal machines), which just returns the original value. More specifically, if my query function is used like this: =GETALLDATA(Startdate, Enddate, Stockticker, etc) I would like to transparently swap the function behind the call. Do you see any hope, or am I lost? I appreciate your help. PS: Of course I'm talking about Bloomberg... Some additional points to clarify issues raise by Frank: The formula in the sheets may not be changed. This is mission-critical software, and its way too complex for any sane person to try and touch it. Only excel and VBA may be used (which is the reason for the previous point...) It would be sufficient to prevent execution of these few specific formulas/functions on a specific machine for all excel sheets to come This looks more and more like a problem for stackoverflow ;-)

    Read the article

  • Is Samba Server what I'm looking for, and if so, what do I need? (currently on DD-WRT Micro)

    - by Anthony
    I am really confused as to what Samba actually does and how it works. Here's what I'm hoping it does: I set up a Samba server on my LAN, and everyone will be able to see each other's shared files and swap them. But some of the documentation makes it sound like it will just allow Mac/Linux computers to see Windows computers. Other bits of the documentation make it sound more like a local server, where a Linux machine would install Samba and they would see everyone and be visible to everyone, but that won't change if anybody else can see each other. While still other things I've read make it seem more like a file-server, where everyone sees each other but file transfers are not peer-to-peer but instead need a host disk for files to act as go between. So, assuming I'm even in the right ballpark of what Samba does in terms of my goal of total cross-visibility on the network, I am left with needing to know what I'd need to set up the server and whether it can be done and is worth it... DD-WRT's article on Samba is a bit ambiguous. One second it sounds as if I can run the server on micro as long as it's set up on a usb drive, but then it also sounds like micro can't run it at all, etc. If I can run it from a usb-connected drive, I still need to know if the files are actually stored on that drive. The dd-wrt article mentions: You can run a Samba server on your main computer and run a client on your router (thus gaining writable storage for the router) or you can use Samba to share a drive connected (typically by USB) to the router among all the computers connected to your network. That one part "to share a drive...among all the computers" makes it sound like the only benefit I get from Samba is a share drive that any OS on the network can see, but they still won't see each other. But I'm very hopeful I'm misreading this. If the computers can see each other but still need the disk, how much space is generally a good idea? I'm basing this on the idea that the drive is a temporary store point. Obviously I'd have to get a drive big enough to store everything people wanted to share if the drive is a full-on file server. If I do have this all wrong, is there any software that achieves what I have in mind? Something that connects to the main router to bridge all clients?

    Read the article

  • Is it possible to "stealth" dual boot a machine?

    - by BrianH
    I have a loaner laptop that has MS Windows with locked down permissions. It works okay for what I need to do, but I started wondering if there was a way to install a separate Windows OS on a separate hard drive to do what I want to do on it. Virtual I wish I could use VirtualBox or VMWare, but that is not an option (I even tried VBox portable). External Drive My next trial was see if it was possible to install Windows on an external drive, and then plug that drive in and boot from it whenever I wanted my own OS. After a few Google searches, I see that is not really a possibility. Swap Primary Drive Another option, would be to get a second internal hard drive, take the existing HD out, and install a new Windows OS on the secondary HD. This would mean swapping the internal hard drive each time I want to switch OSs - doable, but not very convenient. Dual Boot The laptop has an expansion slot where a second hard drive can be plugged in quickly. I thought about Dual booting, but I don't want to mess with the MBR on the primary hard drive. When I have to give the laptop back, I don't want a dual-boot screen to popup. Summary Is there a way to have 2 hard-drives on a machine, each with it's own OS, and maybe use BIOS settings to have only 1 hard drive active at a time? That way both hard drives could be physically connected, but only one would actually be active at a time. I basically want a second OS that does not (can not) affect the existing OS in any way, and can be removed at any time without affecting the existing OS. The secondary OS does not need any of the files on the main hard drive - it's basically like having 2 separate computers using the same hard ware... Is this possible, or would it be easier just to go out and buy a different laptop? Thanks in advance! EDIT I just discovered that my BIOS allows me to pick (at startup) which hard drive I want to boot from. I poked around in the BIOS and there is not a place to disable certain devices, like the primary hard drive. My only concern about plugging in a second hard drive and installing Windows to the second hard drive is that it will mess with the primary hard drive, or add a bootloader screen to pick which windows install to use. My thought would be to physically unplug the primary, plug in the secondary and install windows to the secondary. After the install is working properly, I can plug the primary back in and use the BIOS feature to determine which drive to boot to. Is there any way after I have 2 separate installs on 2 separate hard drives that one of the installs could mess with the MBR on the other drive?

    Read the article

  • mongodb : Can create new thread on FreeBSD?

    - by user197739
    We experienced some strange thing in our mongodb gridfs platform. The platform actually is a bi Xeon E5 (bi quad core) with 128GB of memory, running on freebsd 9 with a zfs pool dedicated for mongodb. [root@mongofile1 ~]# uname -sr FreeBSD 9.1-RELEASE our /boot/loader.conf vfs.zfs.arc_min="2048M" vfs.zfs.arc_max="7680M" vm.kmem_size_max="16G" vm.kmem_size="12G" vfs.zfs.prefetch_disable="1" kern.ipc.nmbclusters="32768" /etc/sysctl.conf net.inet.tcp.msl=15000 net.inet.tcp.keepidle=300000 kern.ipc.nmbclusters=32768 kern.ipc.maxsockbuf=2097152 kern.ipc.somaxconn=8192 kern.maxfiles=65536 kern.maxfilesperproc=32768 net.inet.tcp.delayed_ack=0 net.inet.tcp.sendspace=65535 net.inet.udp.recvspace=65535 net.inet.udp.maxdgram=57344 net.local.stream.recvspace=65535 net.local.stream.sendspace=65535 we follow the recommendation for the ulimit : [root@mongofile1 ~]# su - mongodb $ ulimit -a cpu time (seconds, -t) unlimited file size (512-blocks, -f) unlimited data seg size (kbytes, -d) 33554432 stack size (kbytes, -s) 524288 core file size (512-blocks, -c) unlimited max memory size (kbytes, -m) unlimited locked memory (kbytes, -l) unlimited max user processes (-u) 5547 open files (-n) 32768 virtual mem size (kbytes, -v) unlimited swap limit (kbytes, -w) unlimited sbsize (bytes, -b) unlimited pseudo-terminals (-p) unlimited This server have a twin (same config exactly) for ReplSet in other data center and we have a virtualized arbiter. Some time, almost 3 days, the process of mongodb exit. The problem begin with: Fri Nov 8 11:27:31.741 [conn774697] end connection 192.168.10.162:47963 (23 connections now open) Fri Nov 8 11:27:31.770 [initandlisten] can't create new thread, closing connection Fri Nov 8 11:27:31.771 [rsHealthPoll] replSet member mongofile2:27017 is now in state DOWN Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.162:47968 #774702 (20 connections now open) Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.161:28522 #774703 (21 connections now open) Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.164:15406 #774704 (22 connections now open) Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.163:25750 #774705 (23 connections now open) Fri Nov 8 11:27:31.810 [initandlisten] connection accepted from 192.168.10.182:20779 #774706 (24 connections now open) Fri Nov 8 11:27:31.855 [initandlisten] connection accepted from 192.168.10.161:28524 #774707 (25 connections now open) Fri Nov 8 11:27:31.869 [initandlisten] connection accepted from 192.168.10.182:20786 #774708 (26 connections now open) and after many "can create new thread" [root@mongofile1 /usr/mongodb]# tail -n 15000 mongod.log.old |grep "create new thread"|wc 5020 55220 421680 and finish by a magnificent Fri Nov 8 11:30:22.333 [rsMgr] replSet warning caught unexpected exception in electSelf() pure virtual method called Fri Nov 8 11:30:22.333 Got signal: 6 (Abort trap: 6). Fri Nov 8 11:30:22.337 Backtrace: 0x599efc 0x8035cb516 0x599efc <_ZN5mongo10abruptQuitEi+988> at /usr/local/bin/mongod 0x8035cb516 <_pthread_sigmask+918> at /lib/libthr.so.3 Extract of mongodb from top 78126 mongodb 77 20 0 1253G 1449M sbwait 0 0:20 0.00% mongod If I restart the process when it crash, the problem is fixed for almost 3 days. Has anyone seen this before, or know of a fix?

    Read the article

  • Can't Move Windows to 2nd Monitor without Left Mouse and Cntl Key

    - by John C
    I have 2 very frustrating problems that maybe someone can help me with: I have 2 monitors (different sizes and resolutions) setup with the "Extended" monitor Win7 setup. My problem is this = I can not "move" a window from my Primary Monitor (larger and higher resolution on right side in front of me) to my Secondary 2nd monitor (smaller and lower resolution) with just selecting the title bar with the left mouse button and dragging it to the left. Windows 7 "snaps" it back to the left Primary Monitor when the window is physically in the 2nd window area as I'm holding the left mouse button. I can prevent this problem - by holding down the Cntl Key with the Left Mouse button, but this is extremely annoying to me. Also I typically "lose" focus if I try typing input on the 2nd monitor. Typing is erratic with regard to keystroke accuracy from my keyboard translated into input on the 2nd screen. No problem with typing input on the primary left monitor. I find this extremely annoying in Windows 7 and turning off the "snap" feature via the Control panel does NOT work for me. Win7 stubbornly refuses to move my selected window to my 2nd monitor without me "forcing" Win7 to do this with the Cntrl Key. Please tell me this is not a Win7 feature. Also on my system - Windows Key + Shift, Left arrow Key (pressed together) or the same combo with The Right arrow Key - don't do anything whatsoever. Widows Key with "+" however does maximize current window across both monitors, and I can "restore" it with Windows Key and "-" back to original monitor and size. I have tried various solutions including changing the resolutions of one or both of my monitors and sometimes "temporarily helps" but reverts back to the problem. Also if I swap the logical (not physical) layout so that I tell Win7 the monitors are setup in a reserved situation (Large monitor on the left, and small on the right) - this also sometimes helps for awhile - and is very strange and awkward to work with "backwards". But all of these solutions stop working. The only solution that consistently works for "moving" the screens is to hold the Cntrl Key down as I'm moving window with the left mouse selected on the title bar. Even that however, doesn't prevent the loss of typing focus for me on the 2nd monitor - while at the same time the typing on the 1st monitor is fine. Any help on moving my window screens from one monitor on my 2nd monitor without having to press the Cntrl key while holding down my left mouse button with be appreciated. Also any help on gaining typing "focus" into my 2nd screen with be helpful too. Thanks - John

    Read the article

  • Windows 7 Home hangs at "Welcome" screen

    - by White Phoenix
    I'm asking on behalf of a friend who's currently having problems with his machine. Windows 7 Home 32-bit. He's too far away for me to help by going over to his house - I'm helping him over the Internet. This is his current machine: http://www.newegg.com/Product/Product.aspx?Item=N82E16883227134 The only two changes he made to that machine is to swap out the gfx card for a EVGA GTX 460 and the PSU for a Corsair TX650. Here's what happened: He was playing a computer game (fairly CPU/GPU intensive) and had some music going in the background in foobar while playing. Suddenly, he notices the music stopped playing, so he switches to foobar to try to close it, but it freezes up (window won't respond). So he figures it's just foobar having a bad day and force quits that program. Suddenly, his game won't respond, so he force quits that, then the entire computer just went to crap at that point, so he hits the restart button on his machine. Computer POSTS fine, but now he gets stuck at the Windows "welcome" screen (his account is set to auto-login). HD activity light is solid yellow but he doesn't hear HDD activity. He tried booting into Safe Mode - gets stuck at the "welcome screen". Tried a STartup Repair within Windows 7, it found a few problems, but still gets stuck at welcome. I advised him to boot off the DVD - sfc /scannow found nothing (couldn't use the regular /scannow option; says there's a repair pending, had to use use offbootdir/offwindir command switches). Ran startup repair 3 times - found nothing. My friend runs virus/malware scans on a regular basis, so he's fairly sure it's not that either. Right now I'm having my friend run chkdsk /R on the computer while in this Startup Recovery mode - so far it's caught a few bad sectors. However at this point I'm kinda wondering which way to go if chkdsk doesn't fix it. Quick Google search said someone had success by booting Windows with bootlogging on - some others have success with running the aforemented chkdsk, etc. The fact that Windows cannot even boot into Safe Mode concerns me. While we're waiting for chkdsk /R to finish, are there any other options I can give my friend short of reinstalling Windows 7? He has his data on a separate partition so that's not a major problem (though it'll be an annoyance for him). I suspect his hard drive may be having some issues, but my main concern is getting him back up and running before we start diagnosing the hard drive (I may have him run some sort of SMART test utility later).

    Read the article

  • New CentOS/cPanel servers showing high load averages at idle

    - by Jax
    I have taken delivery of two identically specced CentOS/cPanel servers, showing the same behaviour of a resting load average of 1.30, 1.21, 1.16 and yet the CPU is sitting 100% idle. Hardware: Xeon(R) CPU E3-1270 4GB RAM Behavior:- top shows CPU 99.9% idle virtually no disk IO Some command output :- uname -a Linux server.myserver.com 2.6.18-308.4.1.el5PAE #1 SMP Tue Apr 17 17:47:38 EDT 2012 i686 i686 i386 GNU/Linux top top - 10:37:50 up 1:47, 1 user, load average: 1.28, 1.20, 1.17 Tasks: 199 total, 1 running, 198 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni, 99.9%id, 0.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4125104k total, 438764k used, 3686340k free, 25788k buffers Swap: 2096440k total, 0k used, 2096440k free, 291080k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1 root 15 0 2160 640 552 S 0.0 0.0 0:00.89 init 2 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/0 3 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/0 4 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/0 5 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/1 6 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/1 7 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/1 8 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/2 9 root 35 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/2 10 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/2 11 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/3 12 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/3 13 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/3 14 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/4 15 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/4 16 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/4 17 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/5 18 root 38 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/5 19 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/5 20 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/6 21 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/6 22 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/6 23 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/7 24 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/7 25 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/7 26 root 10 -5 0 0 0 S 0.0 0.0 0:06.42 events/0 27 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 events/1 28 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 events/2 29 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 events/3 30 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 events/4 31 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 events/5 32 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 events/6 33 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 events/7 34 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 khelper 35 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kthread 45 root 13 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/0 46 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/1 47 root 14 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/2 48 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/3 49 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/4 50 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/5 51 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/6 52 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/7 53 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kacpid 189 root 11 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/0 190 root 11 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/1 191 root 12 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/2 192 root 12 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/3 193 root 13 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/4 194 root 13 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/5 195 root 14 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/6 196 root 14 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/7 199 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 khubd ps axf PID TTY STAT TIME COMMAND 1 ? Ss 0:00 init [3] 2 ? S< 0:00 [migration/0] 3 ? SN 0:00 [ksoftirqd/0] 4 ? S< 0:00 [watchdog/0] 5 ? S< 0:00 [migration/1] 6 ? SN 0:00 [ksoftirqd/1] 7 ? S< 0:00 [watchdog/1] 8 ? S< 0:00 [migration/2] 9 ? SN 0:00 [ksoftirqd/2] 10 ? S< 0:00 [watchdog/2] 11 ? S< 0:00 [migration/3] 12 ? SN 0:00 [ksoftirqd/3] 13 ? S< 0:00 [watchdog/3] 14 ? S< 0:00 [migration/4] 15 ? SN 0:00 [ksoftirqd/4] 16 ? S< 0:00 [watchdog/4] 17 ? S< 0:00 [migration/5] 18 ? SN 0:00 [ksoftirqd/5] 19 ? S< 0:00 [watchdog/5] 20 ? S< 0:00 [migration/6] 21 ? SN 0:00 [ksoftirqd/6] 22 ? S< 0:00 [watchdog/6] 23 ? S< 0:00 [migration/7] 24 ? SN 0:00 [ksoftirqd/7] 25 ? S< 0:00 [watchdog/7] 26 ? S< 0:06 [events/0] 27 ? S< 0:00 [events/1] 28 ? S< 0:00 [events/2] 29 ? S< 0:00 [events/3] 30 ? S< 0:00 [events/4] 31 ? S< 0:00 [events/5] 32 ? S< 0:00 [events/6] 33 ? S< 0:00 [events/7] 34 ? S< 0:00 [khelper] 35 ? S< 0:00 [kthread] 45 ? S< 0:00 \_ [kblockd/0] 46 ? S< 0:00 \_ [kblockd/1] 47 ? S< 0:00 \_ [kblockd/2] 48 ? S< 0:00 \_ [kblockd/3] 49 ? S< 0:00 \_ [kblockd/4] 50 ? S< 0:00 \_ [kblockd/5] 51 ? S< 0:00 \_ [kblockd/6] 52 ? S< 0:00 \_ [kblockd/7] 53 ? S< 0:00 \_ [kacpid] 189 ? S< 0:00 \_ [cqueue/0] 190 ? S< 0:00 \_ [cqueue/1] 191 ? S< 0:00 \_ [cqueue/2] 192 ? S< 0:00 \_ [cqueue/3] 193 ? S< 0:00 \_ [cqueue/4] 194 ? S< 0:00 \_ [cqueue/5] 195 ? S< 0:00 \_ [cqueue/6] 196 ? S< 0:00 \_ [cqueue/7] 199 ? S< 0:00 \_ [khubd] 201 ? S< 0:00 \_ [kseriod] 301 ? S 0:00 \_ [khungtaskd] 302 ? S 0:00 \_ [pdflush] 303 ? S 0:00 \_ [pdflush] 304 ? S< 0:00 \_ [kswapd0] 305 ? S< 0:00 \_ [aio/0] 306 ? S< 0:00 \_ [aio/1] 307 ? S< 0:00 \_ [aio/2] 308 ? S< 0:00 \_ [aio/3] 309 ? S< 0:00 \_ [aio/4] 310 ? S< 0:00 \_ [aio/5] 311 ? S< 0:00 \_ [aio/6] 312 ? S< 0:00 \_ [aio/7] 472 ? S< 0:00 \_ [kpsmoused] 551 ? S< 0:00 \_ [ata/0] 552 ? S< 0:00 \_ [ata/1] 553 ? S< 0:00 \_ [ata/2] 554 ? S< 0:00 \_ [ata/3] 555 ? S< 0:00 \_ [ata/4] 556 ? S< 0:00 \_ [ata/5] 557 ? S< 0:00 \_ [ata/6] 558 ? S< 0:00 \_ [ata/7] 559 ? S< 0:00 \_ [ata_aux] 569 ? S< 0:00 \_ [scsi_eh_0] 570 ? S< 0:00 \_ [scsi_eh_1] 571 ? S< 0:00 \_ [scsi_eh_2] 572 ? S< 0:00 \_ [scsi_eh_3] 573 ? S< 0:00 \_ [scsi_eh_4] 574 ? S< 0:00 \_ [scsi_eh_5] 593 ? S< 0:00 \_ [kstriped] 630 ? S< 0:00 \_ [kjournald] 655 ? S< 0:00 \_ [kauditd] 1860 ? S< 0:00 \_ [kmpathd/0] 1861 ? S< 0:00 \_ [kmpathd/1] 1862 ? S< 0:00 \_ [kmpathd/2] 1863 ? S< 0:00 \_ [kmpathd/3] 1864 ? S< 0:00 \_ [kmpathd/4] 1865 ? S< 0:00 \_ [kmpathd/5] 1866 ? S< 0:00 \_ [kmpathd/6] 1867 ? S< 0:00 \_ [kmpathd/7] 1868 ? S< 0:00 \_ [kmpath_handlerd] 1902 ? S< 0:00 \_ [kjournald] 1904 ? S< 0:00 \_ [kjournald] 1906 ? S< 0:00 \_ [kjournald] 1908 ? S< 0:00 \_ [kjournald] 1910 ? S< 0:00 \_ [kjournald] 2184 ? S< 0:00 \_ [iscsi_eh] 2288 ? S< 0:00 \_ [cnic_wq] 2298 ? S< 0:00 \_ [bnx2i_thread/0] 2299 ? S< 0:00 \_ [bnx2i_thread/1] 2300 ? S< 0:00 \_ [bnx2i_thread/2] 2301 ? S< 0:00 \_ [bnx2i_thread/3] 2302 ? S< 0:00 \_ [bnx2i_thread/4] 2303 ? S< 0:00 \_ [bnx2i_thread/5] 2304 ? S< 0:00 \_ [bnx2i_thread/6] 2305 ? S< 0:00 \_ [bnx2i_thread/7] 2330 ? S< 0:00 \_ [ib_addr] 2359 ? S< 0:00 \_ [ib_mcast] 2360 ? S< 0:00 \_ [ib_inform] 2361 ? S< 0:00 \_ [local_sa] 2371 ? S< 0:00 \_ [iw_cm_wq] 2381 ? S< 0:00 \_ [ib_cm/0] 2382 ? S< 0:00 \_ [ib_cm/1] 2383 ? S< 0:00 \_ [ib_cm/2] 2384 ? S< 0:00 \_ [ib_cm/3] 2385 ? S< 0:00 \_ [ib_cm/4] 2386 ? S< 0:00 \_ [ib_cm/5] 2387 ? S< 0:00 \_ [ib_cm/6] 2388 ? S< 0:00 \_ [ib_cm/7] 2398 ? S< 0:00 \_ [rdma_cm] 2684 ? S< 0:00 \_ [bond0] 2882 ? S< 0:00 \_ [bond1] 3195 ? S< 0:00 \_ [kondemand/0] 3197 ? S< 0:00 \_ [kondemand/1] 3198 ? S< 0:00 \_ [kondemand/2] 3199 ? S< 0:00 \_ [kondemand/3] 3200 ? S< 0:00 \_ [kondemand/4] 3201 ? S< 0:00 \_ [kondemand/5] 3202 ? S< 0:00 \_ [kondemand/6] 3203 ? S< 0:00 \_ [kondemand/7] 688 ? S<s 0:00 /sbin/udevd -d 2425 ? S<Lsl 0:00 iscsiuio 2432 ? Ss 0:00 iscsid 2434 ? S<Ls 0:00 iscsid 3061 ? S<sl 0:00 auditd 3063 ? S<sl 0:00 \_ /sbin/audispd 3121 ? Ss 0:00 syslogd -m 0 3124 ? Ss 0:00 klogd -x 3220 ? Ss 0:00 irqbalance 3278 ? Ss 0:00 dbus-daemon --system 3324 ? Ss 0:00 /usr/sbin/acpid 3337 ? Ss 0:00 hald 3338 ? S 0:00 \_ hald-runner 3345 ? S 0:00 \_ hald-addon-acpi: listening on acpid socket /var/run/acpid.socket 3349 ? S 0:00 \_ hald-addon-keyboard: listening on /dev/input/event1 3360 ? S 0:00 \_ hald-addon-storage: polling /dev/sr0 3413 ? Ssl 0:00 automount 3435 ? Ssl 0:00 /usr/sbin/named -u named 3466 ? Ss 0:00 /usr/sbin/sshd 4072 ? Ss 0:00 \_ sshd: root@pts/0 4078 pts/0 Ss 0:00 \_ -bash 5436 pts/0 R+ 0:00 \_ ps axf 3484 ? Ss 0:00 xinetd -stayalive -pidfile /var/run/xinetd.pid 3500 ? SLs 0:00 ntpd -u ntp:ntp -p /var/run/ntpd.pid -g 3514 ? S 0:00 /bin/sh /usr/bin/mysqld_safe --datadir=/var/lib/mysql --pid-file=/var/lib/mysql/server.myserver.com.pid 3575 ? Sl 0:00 \_ /usr/sbin/mysqld --basedir=/ --datadir=/var/lib/mysql --user=mysql --log-error=/var/lib/mysql/server.myserver.com.err --pid-fil 3687 ? Ss 0:00 /usr/sbin/exim -bd -q1h 3709 ? Ss 0:00 /usr/sbin/dovecot 3710 ? S 0:00 \_ dovecot-auth 3725 ? S 0:00 \_ pop3-login 3726 ? S 0:00 \_ pop3-login 3727 ? S 0:00 \_ imap-login 3728 ? S 0:00 \_ imap-login 3729 ? Ss 0:00 /usr/local/apache/bin/httpd -k start -DSSL 4326 ? S 0:00 \_ /usr/bin/perl /usr/local/cpanel/bin/leechprotect 4332 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4333 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4334 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4335 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4336 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4337 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4382 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4383 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4384 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 5389 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 5390 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 3741 ? Ss 0:00 pure-ftpd (SERVER) 3746 ? S 0:00 /usr/sbin/pure-authd -s /var/run/ftpd.sock -r /usr/sbin/pureauth 3759 ? Ss 0:00 crond 3772 ? Ss 0:00 /usr/sbin/atd 3909 ? S 0:00 cpsrvd (SSL) - waiting for connections 5435 ? Z 0:00 \_ [cpsrvd-ssl] <defunct> 3931 ? S 0:00 queueprocd - wait to process a task 3948 ? S 0:00 tailwatchd 3954 ? SN 0:00 cpanellogd - sleeping for logs 4003 ? Ss 0:00 ./nimbus /opt/nimsoft 4016 ? S 0:00 \_ nimbus(controller) 4053 ? Sl 0:00 \_ nimbus(spooler) 4066 ? S 0:00 \_ nimbus(hdb) 4069 ? S 0:00 \_ nimbus(cdm) 4070 ? S 0:00 \_ nimbus(processes) 4023 ? S 0:00 /usr/sbin/smartd -q never 4027 tty1 Ss+ 0:00 /sbin/mingetty tty1 4028 tty2 Ss+ 0:00 /sbin/mingetty tty2 4029 tty3 Ss+ 0:00 /sbin/mingetty tty3 4030 tty4 Ss+ 0:00 /sbin/mingetty tty4 4031 tty5 Ss+ 0:00 /sbin/mingetty tty5 4033 tty6 Ss+ 0:00 /sbin/mingetty tty6 4035 ttyS1 Ss+ 0:00 /sbin/agetty -h -L ttyS1 19200 vt100 vmstat 10 6 procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 0 0 0 3718136 25684 257424 0 0 8 3 127 189 0 0 100 0 0 0 0 0 3718136 25700 257420 0 0 0 7 1013 1500 0 0 100 0 0 0 0 0 3718136 25700 257424 0 0 0 1 1013 1551 0 0 100 0 0 0 0 0 3718136 25700 257424 0 0 0 0 1012 1469 0 0 100 0 0 1 0 0 3712680 25716 257424 0 0 0 2 1013 1542 0 0 100 0 0 0 0 0 3718376 25740 257424 0 0 0 46 1017 1534 0 0 100 0 0 Can anyone advise me as to what is the cause of and how I may resolve this behaviour? A kernel/driver conflict perhaps? I don't see any processes in R or D state that might inflate the load averages artificially, I realise it may be considered low in an 8 thread system but its higher at idle than any normal behaviour I've previously come across. Thanks in advance for your time. Edit: iotop Total DISK READ: 0.00 B/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO> COMMAND 26 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.29 % [events/0] 3205 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.10 % [kondemand/2] 3208 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [kondemand/5] 3209 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [kondemand/6] 3207 be/3 root 0.00 B/s 0.00 B/s 0.10 % 0.00 % [kondemand/4] 3210 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [kondemand/7] 3227 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % irqbalance 3288 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [rpciod/1] 3287 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [rpciod/0] 3206 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [kondemand/3] 3069 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % auditd 3070 be/2 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % audispd 655 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [kauditd] 3619 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % automount 3 be/7 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [ksoftirqd/0] 3068 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % auditd 29 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [events/3] 4 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/0] 7 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/1] 10 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/2] 13 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/3] 16 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/4] 19 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/5] 22 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/6] 25 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/7] 27 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [events/1] 28 be/3 root 0.00 B/s 0.00 B/s 0.29 % 0.00 % [events/2] 30 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [events/4] 31 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [events/5] 32 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [events/6] 33 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [events/7] 34 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [khelper] 35 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [kthread] 45 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [kblockd/0]

    Read the article

< Previous Page | 72 73 74 75 76 77 78 79 80 81 82 83  | Next Page >