Search Results

Search found 18596 results on 744 pages for 'c how to detect all ip addresses from a lan'.

Page 77/744 | < Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >

• Getting my IP off the hotmail blacklist

  - by Kai

  I got a new server with a new IP address. Apparently this IP is listed in the hotmail blacklists so that I can't send mails to hotmail users out of my webapplication. postfix/smtp[24706]: 8F31C9404B: to=<[email protected]>, relay=mx3.hotmail.com[65.55.37.88]:25, delay=0.66, delays=0.01/0/0.48/0.16, dsn=5.0.0, status=bounced (host mx3.hotmail.com[65.55.37.88] said: 550 SC-001 Unfortunately, messages from 78.47.228.xxx weren't sent. Please contact your Internet service provider since part of their network is on our block list. You can also refer your provider to http://mail.live.com/mail/troubleshooting.aspx#errors. (in reply to MAIL FROM command)) My hoster will not help me get that address removed from the blacklist. So I tried to find a way to do it on my own, but I can't find a way to ask Microsoft to remove my IP from that list. Has anyone managed to remove a falsely listed address? And if yes: how?

  Read the article

• Multiple External IP Ranges on a Juniper SSG5

  - by Sam

  I have a Juniper SSG 5 firewall in a datacenter. The first interface (eth0/0) has been assigned a static IP address and has three other addresses configured for VIP Nat. I have a static route configured at the lowest priority for 0.0.0.0/0 to my hosting company's gateway. Now I need to configure a second IP block. I have the IPs assigned to the second interface (eth0/1) which is in the same security zone and virtual router as the first. However, with this interface enabled I (a) can't initiate outbound sessions (browse the internet, ping, DNS lookup, etc) even though I can access servers behind the firewall just fine from the outside and (b) can't ping the management IP of the firewall/gateway. I've tried anything I can think of but I guess this is a little above my head. Could anyone point me in the right direction? Interfaces: ethernet0/0 xxx.xxx.242.4/29 Untrust Layer3 ethernet0/1 xxx.xxx.152.0/28 Untrust Layer3 Routes: http://i.stack.imgur.com/60s41.png

  Read the article

• MAC and IP adress text-identicon as avatar

  - by rubo77

  I would like to create something like identicons but not with images but with a unique word for each IP-Adresses and MAC-Adresses. create an easy to remember alias for a mac address, that is unique and reverse lookupable, for example: IP 123.456.789.132 will result in an alias for that IP, that is connected to an existing word from a wordlist, that is unique. Background of this idea: this way we could identify our Routers in our Opennet in Hamburg easily in a graphical NodeGraph. Is there some site already, where I can convert MAC-Adresses to unique human readeable words?

  Read the article

• How to get started with tcp/ip v6?

  - by Johan

  Hi Now and then there is "news" about that the ip numbers will run out in X years, and we must change to tcp/ip v6... And even thou this crisis never really happens it has waken a question, how do you get started with tcp/ip v6? What can I do at home and is this a good or bad idea? Can you use IPv4 and IPv6 in the same cables in the same LAN, or do you need to physically separate them? Can you have some translation box so you can reach the "normal" internet from the IPv6 connected devices? (Just like a NAT-Router) Can someone please clarify the situation a little bit? Thanks Johan

  Read the article

• Log under proxy server about communication between clients

  - by Kumar P

  I am using RHEL5 as proxy server with few windows xp client boxes. Windows machines using IP messenger for communicating between client machines in local network. But as a administrator i want to record their communication by ip messenger. How can i do it ? Help me to do it.

  Read the article

• DHCP Lease time

  - by DanSpd

  Hello, I have computer connected to internet directly. But once very hour IP changes and I do not want that for sure. How can I set IP lease time for like a year or so? Thank you

  Read the article

• Allow Single IP to access ASP.NET Web Service (ASMX) using Firewall

  - by Suresh Agrawal

  I have one asp.net web service (asmx) in separate project that is hosted on windows server having other asp.net web applications running on it. How can I restrict asp.net web service to be accessed by single IP address? I want that my web service must be accessed by one IP configured by me. If requests comes from any other IP, it must not reach to my web service and discarded by windows firewall itself. I know that this is something to do with windows firewall. I did it for SQL Server previously, but I don't know how to configure single asp.net web service project to do so.

  Read the article

• Multiple IPs on single server - Specify which is used to connect (MS server 2008 / DNS)

  - by runboy

  I have a Windows 2008 server with multiple IPs that is acting as DNS server. I have set the DNS server up to only accept connections on a single of these IPs. The DNS is serving as secondary DNS and when it connects to the primary DNS server it is not connecting with this particular IP address, but one of the other IPs. Is there a way in which I can make sure the server connects using the correct IP?

  Read the article

• Configuring HP Proliant iLO using hponcfg

  - by Abhay Kumar

  I am configuring an iLO using hponcfg by logging into the machine remotely and running hponcfg with scripts Mod_Directory.xml and then with Mod_Network.xml. I am enabling the DHCP on the device. But after the above scripts are executed successfully and upon rebooting the iLO, it shows the IP address to be 0.0.0.0. What is missing here, so that the iLO gets an IP from DHCP automatically after configuration?

  Read the article

• Tomcat cannot connect to MySQL on localhost

  - by David

  Hi, I have deployed an application on my Tomcat server with JDBC resources defined. What is puzzling me is that I can connect to the database (which is running locally on the server) only using the server's IP. When I change the resource host to localhost (or 127.0.0.1) then MySQL rejects the connection. I don't want to be connection via the server's IP but rather locally. What do I do? Thanks!

  Read the article

• Windows 7 - Virtualbox host only adapter doesn't get an IP

  - by Craig

  When I create a new host only network adapter, it will not set the IP address I assign to it. After I save the IP address & netmask it looks like it works (I see the Windows 7 User Account Control verification box), but the IP address doesn't get stored on the adapter. I have tried adding/removing the adapter from within virtualbox and settings the values manually in the Windows aapter settings dialogue. I am using a Windows 7 host. Does anyone know why the settings don't get saved, or how to get more information? C:\Program Files\Oracle\VirtualBox>VBoxManage list hostonlyifs Name: VirtualBox Host-Only Ethernet Adapter GUID: 1721835e-e2c8-4f52-90fe-df7227ebe037 DHCP: Disabled IPAddress: 0.0.0.0 NetworkMask: 0.0.0.0 IPV6Address: IPV6NetworkMaskPrefixLength: 0 HardwareAddress: 00:00:00:00:00:00 MediumType: Unknown Status: Unknown VBoxNetworkName: HostInterfaceNetworking-VirtualBox Host-Only Ethernet Adapter

  Read the article

• haproxy - pass original / remote ip in tcp mode

  - by Vito Botta

  I've got haproxy set up with keepalived for load balancing and ip failover of a percona cluster, and since it works great I'd like to use the same lb / failover for another service/daemon. I've configured haproxy this way: listen my_service 0.0.0.0:4567 mode tcp balance leastconn option tcpka contimeout 500000 clitimeout 500000 srvtimeout 500000 server host1 xxx.xxx.xxx.xx1:4567 check port 4567 inter 5000 rise 3 fall 3 server host2 xxx.xxx.xxx.xx2:4567 check port 4567 inter 5000 rise 3 fall 3 The load balancing works fine, but the service sees the IP of the load balancer instead of the actual IPs of the clients. In http mode it's quite easy to have haproxy pass along the remote IP, but how do I do in tcp mode? This is critical due to the nature of the service I need to load balance. Thanks! Vito

  Read the article

• Hosting 3 domains on 3 PC (1 domain per PC) with only 1 static IP address

  - by StealthRT

  Hey all i am trying to figure this out here. I have 3 PC's that are hooked into my router which i have a static IP for. I am currently hosting a web site (ex: blah1.com) on the 1st PC but have yet to connect PC 2 and 3 up to the network. That one PC thats online is using port 77. I direct all 80 traffic to port 77 using that servers IP address (192.168.x.xxx) My question is, how can i direct traffic for my other 2 domains (ex: blah2.com and blah3.com) to the 2 individual PC's (ip's) as i already am doing with the 1st PC if i can only use one port 80 to direct taffic to the website in?

  Read the article

• phpmyadmin forbidden after changing config for my IP

  - by Jonathan Kushner

  I followed the phpmyadmin setup and changed the config to require ip my ipaddress and allow from my ipaddress and its still telling me forbidden You don't have permission to access /phpmyadmin on this server. when I try to access the page on my browser (my server is not located on my machine). I installed everything using root. I also chmod 775 the entire phpMyAdmin folder. Im running RHEL 6.1. Any idea what to do at this point? Here is my /etc/httpd/conf.d/phpMyAdmin.conf: <Directory /usr/share/phpMyAdmin/> <IfModule mod_authz_core.c> # Apache 2.4 <RequireAny> Require ip myserveripaddress Require ip ::1 </RequireAny> </IfModule> <IfModule !mod_authz_core.c> # Apache 2.2 Order Deny,Allow Deny from All Allow from myserveripaddress Allow from ::1 </IfModule> </Directory>

  Read the article

• IP Tunneling for Spotify? [closed]

  - by everwicked

  I was in the UK and enjoyed Spotify relentlessly. Now I've moved back to Greece and I can't even pay for the darn thing. So my idea was this- I have a server in France and it has a fail-over IP in the UK. So I installed a proxy server on it and made it listen to the UK IP. So far so good. Then, I played Spotify for a while through the proxy server just fine, and it thought I was in the UK. But now... it gives me an error message that I'm in another country than the one on my profile (UK). I don't really understand why - maybe they also geolocate the IP address of the client, not just the proxy server? Either way, I'm kinda stuck - is there a way to tunnel Spotify's network traffic through my server transparently? Maybe a VPN or something similar? Thanks

  Read the article

• Nginx Ip Whitelist

  - by Will

  Is it possible to create a ip whitelist for my nginx proxy server without adding allow or deny in the config file is it possible i can get nginx to link to a separate database to check if the user is allowed to access the website . Ideally i could do with nginx linking to an external database or at minimum a list off allowed ips on the same server so i can easily update the list whit out restarting nginx every time. In the future i would like to link nginx to my website and a user will login and there ip will be linked to there account and they will be able to update there ip if it has changed to there new one to grant them access so i need to keep in mind that it would be easyer to do this if i have external list off ips in some kind off database any help is apreshiated

  Read the article

• Trouble Connecting to Virtual Machine after IP address Change

  - by David

  I have a VMware image running a copy of Fedora 11 which is hosted on a remote server. The remote server recently had its IP address change. I'm now unable to connect to my virtual machine. The server admin assures me that my virtual machine is running and assigned the new IP address. I have checked the firewalls and had the remote admin restart the VM instance. Neither of these fixed the problem. How do I troubleshoot a remote server which I am unable to SSH to? I'm actually even unable to ping the remote IP (connection timed out).

  Read the article

• Accessing SQL with the PC name not the IP

  - by Cornelius

  I'm trying to connect to a SQL instance (default instance) on a machine. When using the IP of the machine it connects to the machine. Using the name of the machine on that machine you are able to establish a connection to the SQL instance but using the machine name on another PC the connection cannot be established. And gives the error A network-related or instance-specific error occurred while establishing a connection to SQL Server. ... (Microsoft Server, Error: 10060) The machine that I am trying to establish the connection from can ping the machine with the SQL instance both on the IP and on the name. Why would this be and how can I fix it? Edit: pinging the name does resolve the correct IP. Pinging the FQDN also works correctly.

  Read the article

• syslog ip ranges to specific files using `rsyslog`

  - by Mike Pennington

  I have many Cisco / JunOS routers and switches that send logs to my Debian server, which uses rsyslogd. How can I configure rsyslogd to send these router / switch logs to a specific file, based on their source IP address? I do not want to pollute general system logs with these entries. For instance: all routers in Chicago (source ip block: 172.17.25.0/24) to only log to /var/log/net/chicago. all routers in Dallas (source ip block 172.17.27.0/24) to only log to /var/log/net/dallas. Finally, these logs should be rotated daily for up to 30 days and compressed. NOTE: I am answering my own question

  Read the article

• UCARP: prevent the original master from taking over the VIP when it comes back after failure?

  - by quanta

  Keepalived can do this by combining the nopreempt option and the BACKUP state on the both nodes: Prevent VRRP Master from becoming Master once it has failed Prevent master to fall back to master after failure How about the UCARP? Name : ucarp Arch : x86_64 Version : 1.5.2 Release : 1.el5.rf Size : 81 k Repo : installed Summary : Common Address Redundancy Protocol (CARP) for Unix URL : http://www.ucarp.org/ License : BSD Description: UCARP allows a couple of hosts to share common virtual IP addresses in order : to provide automatic failover. It is a portable userland implementation of the : secure and patent-free Common Address Redundancy Protocol (CARP, OpenBSD's : alternative to the patents-bloated VRRP). : Strong points of the CARP protocol are: very low overhead, cryptographically : signed messages, interoperability between different operating systems and no : need for any dedicated extra network link between redundant hosts. If I don't use the --preempt option and set the --advskew to the same value, both nodes become master. /etc/sysconfig/carp/vip-010.conf # Virtual IP configuration file for UCARP # The number (from 001 to 255) in the name of the file is the identifier # $Id: vip-001.conf.example 1527 2004-07-09 15:23:54Z dude $ # Set the same password on all mamchines sharing the same virtual IP PASSWORD="pa$$w0rd" # You are required to have an IPADDR= line in the configuration file for # this interface (so no DHCP allowed) BIND_INTERFACE="eth0" # Do *NOT* use a main interface for the virtual IP, use an ethX:Y alias # with the corresponding /etc/sysconfig/network-scripts/ifcfg-ethX:Y file # already configured and ith ONBOOT=no VIP_INTERFACE="eth0:0" # If you have extra options to add, see "ucarp --help" output # (the lower the "-k <val>" the higher priority and "-P" to become master ASAP) OPTIONS="-z -k 255" /etc/sysconfig/network-scripts/ifcfg-eth0:0 DEVICE=eth0:0 ONBOOT=no BOOTPROTO= IPADDR=192.168.6.8 NETMASK=255.255.255.0 USERCTL=yes IPV6INIT=no node 1: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether c6:9b:8e:af:a7:69 brd ff:ff:ff:ff:ff:ff inet 192.168.6.192/24 brd 192.168.6.255 scope global eth0 inet 192.168.6.8/24 brd 192.168.6.255 scope global secondary eth0:0 inet6 fe80::c49b:8eff:feaf:a769/64 scope link valid_lft forever preferred_lft forever node 2: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:30:48:f7:0f:81 brd ff:ff:ff:ff:ff:ff inet 192.168.6.38/24 brd 192.168.6.255 scope global eth1 inet 192.168.6.8/24 brd 192.168.6.255 scope global secondary eth1:0 inet6 fe80::230:48ff:fef7:f81/64 scope link valid_lft forever preferred_lft forever

  Read the article

• Trouble Connecting to Virtual Machine after IP address Change

  - by David

  I have a VMware image running a copy of Fedora 11 which is hosted on a remote server. The remote server recently had its IP address change. I'm now unable to connect to my virtual machine. The server admin assures me that my virtual machine is running and assigned the new IP address. I have checked the firewalls and had the remote admin restart the VM instance. Neither of these fixed the problem. How do I troubleshoot a remote server which I am unable to SSH to? I'm actually even unable to ping the remote IP (connection timed out).

  Read the article

• "IP May Be Forged" - Sendmail Warning

  - by Mikey B

  CentOS 5.x | SendMail 8 Can I get clarification on what exactly the warning "IP may be forged" means and what conditions cause it? I recently configured SendMail to relay email from my exchange server and it's showing that warning in the logs. The messages get delivered fine but I don't like the warnings. I originally thought that there was an inconsistency between the servername used in the EHLO statement from Exchange and the respective PTR record for the source IP for Exchange. But upon examining a packet capture, I see exchange using "EHLO domain.com" and that the source IP has a PTR of "domain.com". Maybe sendmail doesn't like that the greeting only has the domain? -M

  Read the article

• Windows Server 2008: Limit UDP/TCP packets per IP or ban

  - by WBAR

  How I can limit UDP/TCP packets per IP send to my host (or better PORT) per second or minute ? Would be nice to ban that IP for 12/24 hours or even for ever. I got Windows Server 2008 and I'm very poor in Windows administration but quite good in Linux. EDIT: By basic problem is that They sending a lot of rubbish UPD and TCP packets.. TCP packets without SYNCH, fragmented UDP packets so my servers stop responding.. So I need to cut off users (IPs) sending more than X packets per second. I need solution witch provides me, somehow, configurable: X packets of certain type (UDP, TCP or both - lets say parameter named Z ) are allowed to be received by IP on Y port, otherwise this packet should be DROPPED. My virtual hosts are hosted by VirtualBox and I'm able to forward all incoming packets certain type and certain port to the specific Virtual Host, but I need to DROP them before my VirtualBox receive them.

  Read the article

• Apache will not start after IP change

  - by Doron

  I'm running CentOS 5.8 and I had to change my server's IP address. Afterwards, I'm unable start Apache. I am also running virtualmin. The error I'm receiving is: Failed to start service Starting httpd: httpd: Could not reliably determine the server's fully qualified domain name, using 184.106.146.125 for ServerName (99) Cannot assign requested address: make_sock: could not bind to address 50.56.33.100:8080 no listening sockets available, shutting down Unable to open logs I edited my httpd.conf to point to the new IP address like such: #Listen 12.34.56.78:80 Listen 184.106.146.125:80 And looking at the error it still seems to be referring to the old ip address (50.*).

  Read the article

• [Nameservers] Can I setup 5 ips to 1 server and have only 2 nameservers?

  - by Tyler

  So I have 1 computer with 5 IP's and around 15 sites being hosted. I have 4 of the ips setup to be dedicated for 4 sites and the rest share the 5th ip. When I'm setting up my name server, do I set it up at Godaddy my Registar or on my server's dns or both? Can I just setup NS1 - Add all the ips NS2 - Add all the ips And just have all the sites use those two name servers?

  Read the article

< Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >