Search Results

Search found 27496 results on 1100 pages for 'distributed source ctrl'.

Page 77/1100 | < Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >

• Set source address to use tun device does not work (Debian Squeeze)

  - by A. Donda

  there have been similar questions on StackExchange but none of the answers helped me, so I'll try a question of my own. I have a VPN connection via OpenVPN. By default, all traffic is redirected through the tunnel using OpenVPN's "two more specific routes" trick, but I disabled that. My routing table is like this: 198.144.156.141 192.168.2.1 255.255.255.255 UGH 0 0 0 eth0 10.30.92.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun1 10.30.92.1 10.30.92.5 255.255.255.255 UGH 0 0 0 tun1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 10.30.92.5 0.0.0.0 UG 0 0 0 tun1 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0 And the interface configuration is like this: # ifconfig eth0 Link encap:Ethernet HWaddr XX-XX- inet addr:192.168.2.100 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fe8d:acbd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:394869 errors:0 dropped:0 overruns:0 frame:0 TX packets:293489 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:388519578 (370.5 MiB) TX bytes:148817487 (141.9 MiB) Interrupt:20 Base address:0x6f00 tun1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.30.92.6 P-t-P:10.30.92.5 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:64 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:9885 (9.6 KiB) TX bytes:4380 (4.2 KiB) plus the lo device. The routing table has two default routes, one via eth0 through my local network router (DSL modem) at 192.168.2.1, and another via tun1 through the VPN's gateway. With this configuration, if I connect to a site, the route chosen is the direct one (because it has less hops?): # traceroute 8.8.8.8 -n traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 192.168.2.1 0.427 ms 0.491 ms 0.610 ms 2 213.191.89.13 17.981 ms 20.137 ms 22.141 ms 3 62.109.108.48 23.681 ms 25.009 ms 26.401 ms ... This is fine, because my goal is to send only traffic from specific applications through the tunnel (esp. transmission, using its -i / bind-address-ipv4 option). To test whether this can work at all, I check it first with traceroute's -s option: # traceroute 8.8.8.8 -n -s 10.30.92.6 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 * * * 2 * * * 3 * * * ... This I take to mean that connection using the tunnel's local address as source is not possible. What is possible (though only as root) is to specify the source interface: # traceroute 8.8.8.8 -n -i tun1 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 10.30.92.1 129.337 ms 297.758 ms 297.725 ms 2 * * * 3 198.144.152.17 297.653 ms 297.652 ms 297.650 ms ... So apparently the tun1 interface is working and it is possible to send packets through it. But selecting the source interface is not implemented in my actual target application (transmission), so I would like to get source address selection to work. What am I doing wrong?

  Read the article

• ASP.NET JavaScript Routing for ASP.NET MVC–Constraints

  - by zowens

  If you haven’t had a look at my previous post about ASP.NET routing, go ahead and check it out before you read this post: http://weblogs.asp.net/zowens/archive/2010/12/20/asp-net-mvc-javascript-routing.aspx And the code is here: https://github.com/zowens/ASP.NET-MVC-JavaScript-Routing   Anyways, this post is about routing constraints. A routing constraint is essentially a way for the routing engine to filter out route patterns based on the day from the URL. For example, if I have a route where all the parameters are required, I could use a constraint on the required parameters to say that the parameter is non-empty. Here’s what the constraint would look like: Notice that this is a class that inherits from IRouteConstraint, which is an interface provided by System.Web.Routing. The match method returns true if the value is a match (and can be further processed by the routing rules) or false if it does not match (and the route will be matched further along the route collection). Because routing constraints are so essential to the route matching process, it was important that they be part of my JavaScript routing engine. But the problem is that we need to somehow represent the constraint in JavaScript. I made a design decision early on that you MUST put this constraint into JavaScript to match a route. I didn’t want to have server interaction for the URL generation, like I’ve seen in so many applications. While this is easy to maintain, it causes maintenance issues in my opinion. So the way constraints work in JavaScript is that the constraint as an object type definition is set on the route manager. When a route is created, a new instance of the constraint is created with the specific parameter. In its current form the constraint function MUST return a function that takes the route data and will return true or false. You will see the NotEmpty constraint in a bit. Another piece to the puzzle is that you can have the JavaScript exist as a string in your application that is pulled in when the routing JavaScript code is generated. There is a simple interface, IJavaScriptAddition, that I have added that will be used to output custom JavaScript. Let’s put it all together. Here is the NotEmpty constraint. There’s a few things at work here. The constraint is called “notEmpty” in JavaScript. When you add the constraint to a parameter in your C# code, the route manager generator will look for the JsConstraint attribute to look for the name of the constraint type name and fallback to the class name. For example, if I didn’t apply the “JsConstraint” attribute, the constraint would be called “NotEmpty”. The JavaScript code essentially adds a function to the “constraintTypeDefs” object on the “notEmpty” property (this is how constraints are added to routes). The function returns another function that will be invoked with routing data. Here’s how you would use the NotEmpty constraint in C# and it will work with the JavaScript routing generator. The only catch to using route constraints currently is that the following is not supported: The constraint will work in C# but is not supported by my JavaScript routing engine. (I take pull requests so if you’d like this… go ahead and implement it).   I just wanted to take this post to explain a little bit about the background on constraints. I am looking at expanding the current functionality, but for now this is a good start. Thanks for all the support with the JavaScript router. Keep the feedback coming!

  Read the article

• Deeper Integration with phpBB

  - by The Official Microsoft IIS Site

  More good news on the Interoperability front: the new phpBB release is now available for installation from the Windows Web Application Gallery and Web Platform Installer (Web PI) for Windows, IIS and SQL Server. Version 3.0.7-PL1 of phpBB takes advantage of a number of features for PHP applications on the Microsoft Web Platform with Windows, IIS and SQL Server, including SQL Server Driver for PHP 1.1 , which provides key interoperability for PHP applications to use SQL Server or SQL Azure for data...(read more)

  Read the article

• Speaking at NDC 2010!

  - by Chris Hardy (ChrisNTR)

  Hello all, A few weeks ago it was announced that I will be speaking at the Norwegian Developers Conference 2010 on MonoTouch. I'll be doing two session, an introduction to MonoTouch and developing for iPhone, iPod Touch and the iPad as well as deep dive into MonoTouch and the ecosystem that is around MonoTouch and not just the MonoTouch product itself. The conference itself is (what looks to be) in the lovely surrounding of Olso so I'm excited both to visit the country, attend the conference and...(read more)

  Read the article

• Coding standards

  - by Piotr Rodak

  This post will be about coding standards. There are countless articles and blog posts related to this topic, so I know this post will not be too revealing. Yet I would like to mention a few things I came across during my work with the T-SQL code. Naming convention - there are many of them obviously. Too bad if all of them are used in the same database, and sometimes even in the same stored procedure. It is not uncommon to see something like create procedure dbo . Proc1 ( @ParamId int ) as begin declare...(read more)

  Read the article

• Localization with ASP.NET MVC ModelMetadata

  - by kazimanzurrashid

  When using the DisplayFor/EditorFor there has been built-in support in ASP.NET MVC to show localized validation messages, but no support to show the associate label in localized text, unless you are using the .NET 4.0 with Mvc Future. Lets a say you are creating a create form for Product where you have support both English and German like the following. English German I have recently added few helpers for localization in the MvcExtensions, lets see how we can use it to localize the form. As mentioned in the past that I am not a big fan when it comes to decorate class with attributes which is the recommended way in ASP.NET MVC. Instead, we will use the fluent configuration (Similar to FluentNHibernate or EF CodeFirst) of MvcExtensions to configure our View Models. For example for the above we will using: public class ProductEditModelConfiguration : ModelMetadataConfiguration<ProductEditModel> { public ProductEditModelConfiguration() { Configure(model => model.Id).Hide(); Configure(model => model.Name).DisplayName(() => LocalizedTexts.Name) .Required(() => LocalizedTexts.NameCannotBeBlank) .MaximumLength(64, () => LocalizedTexts.NameCannotBeMoreThanSixtyFourCharacters); Configure(model => model.Category).DisplayName(() => LocalizedTexts.Category) .Required(() => LocalizedTexts.CategoryMustBeSelected) .AsDropDownList("categories", () => LocalizedTexts.SelectCategory); Configure(model => model.Supplier).DisplayName(() => LocalizedTexts.Supplier) .Required(() => LocalizedTexts.SupplierMustBeSelected) .AsListBox("suppliers"); Configure(model => model.Price).DisplayName(() => LocalizedTexts.Price) .FormatAsCurrency() .Required(() => LocalizedTexts.PriceCannotBeBlank) .Range(10.00m, 1000.00m, () => LocalizedTexts.PriceMustBeBetweenTenToThousand); } } As you can we are using Func<string> to set the localized text, this is just an overload with the regular string method. There are few more methods in the ModelMetadata which accepts this Func<string> where localization can applied like Description, Watermark, ShortDisplayName etc. The LocalizedTexts is just a regular resource, we have both English and German:   Now lets see the view markup: <%@ Page Language="C#" MasterPageFile="~/Views/Shared/Site.Master" Inherits="System.Web.Mvc.ViewPage<Demo.Web.ProductEditModel>" %> <asp:Content ID="Content1" ContentPlaceHolderID="TitleContent" runat="server"> <%= LocalizedTexts.Create %> </asp:Content> <asp:Content ID="Content2" ContentPlaceHolderID="MainContent" runat="server"> <h2><%= LocalizedTexts.Create %></h2> <%= Html.ValidationSummary(false, LocalizedTexts.CreateValidationSummary)%> <% Html.EnableClientValidation(); %> <% using (Html.BeginForm()) {%> <fieldset> <%= Html.EditorForModel() %> <p> <input type="submit" value="<%= LocalizedTexts.Create %>" /> </p> </fieldset> <% } %> <div> <%= Html.ActionLink(LocalizedTexts.BackToList, "Index")%> </div> </asp:Content> As we can see that we are using the same LocalizedTexts for the other parts of the view which is not included in the ModelMetadata like the Page title, button text etc. We are also using EditorForModel instead of EditorFor for individual field and both are supported. One of the added benefit of the fluent syntax based configuration is that we will get full compile type checking for our resource as we are not depending upon the string based resource name like the ASP.NET MVC. You will find the complete localized CRUD example in the MvcExtensions sample folder. That’s it for today.

  Read the article

• The SQL Server Reporting Services SDK for PHP Debuts

  - by The Official Microsoft IIS Site

  Microsoft has just released the SQL Server Reporting Services SDK for PHP, which enables PHP developers to easily create reports and integrate them in their web applications. The SDK offers a simple Application Programming Interface to interoperate with SQL Server Reporting Services, Microsoft's Reporting and Business Intelligence solution. Developers will be able to use the SDK to perform common operations like listing reports in PHP applications, providing custom report parameters from a PHP...(read more)

  Read the article

• Adding Blog to Your Orchard Website

  - by hajan

  One of the common features in today’s content management systems is to provide you the ability to create your own blog in your website. Also, having a blog is one of the very often needed features for various types of websites. Out of the box, Orchard gives you this, so you can create your own blog in your Orchard website on a pretty easy way. Besides the fact that you can very easily create your own blog, Orchard also gives you some extra features in relation with the support of blogging, such as connecting third-party client applications (e.g. Windows Live Writer) to your blog, so that you can publish blog posts remotely. You can already find all the information provided in this blog post on the http://orchardproject.net website, however I thought it would be nice to make summary in one blog post. I assume you have already installed Orchard and you are already familiar with its environment and administration dashboard. If you haven’t, please read this blog post first.   CREATE YOUR BLOG First of all, go to Orchard Administration Dashboard and click on Blog in the left menu Once you are there, you will see the following screen   Fill the form with all needed data, as in the following example and click Save Right after, you should see the following screen Click New post, and add your first post. After that, go to Homepage (click Your Site in the top-left corner) and you should see the Blog link in your menu After clicking on Blog, you will be directed to the following page Once you click on My First Post, you will see that your blog already supports commenting ability (you can enable/disable this from Administration dashboard in your blog settings) Added comment Adding new comment Submit comment So, with following these steps, you have already setup your blog in your Orchard website.   CONNECT YOUR BLOG WITH WINDOWS LIVE WRITER Since many bloggers prepare their blog posts using third-party client applications, like Windows Live Writer, its very useful if your blog engine has the ability to work with these third-party applications and enable them to make remote posting and publishing. The client applications use XmlRpc interface in order to have the ability to manage and publish the blogs remotely. What is great about Orchard is that it gives you out of the box the XmlRpc and Remote Publishing modules. What you only need to do is to enable these features from the Modules in your Orchard Administration Dashboard. So, lets go through the steps of enabling and making your previously created blog able to work with third-party client applications for blogging. 1. Go to Administration Dashboard and click the Modules After clicking the Modules, you will see the following page: As you can see, you already have Remote Blog Publishing and XmlRpc features for Content Publishing, but both are disabled by default. So, if you click Enable only on Remote Blog Publishing, you will see both of them enabled at once since they are dependent features. After you click Enable, if everything is Ok, the following message should be displayed: So, now we have the featured enabled and ready... The next thing you need to do is to open Windows Live Writer. First, open Windows Live Writer and in your Blog Accounts, click on Add blog account In the next window, chose Other services After that, click on your Blog link in the Orchard website and copy the URL, my URL (on localhost development server) is: http://localhost:8191/blog Then, add your login credentials you use to login in Orchard and click Next. After that, if you have setup everything successfully, the Windows Live Writer will do the rest Once it finishes, you will have window where you can specify the name of your blog you have just connected your Windows Live Writer to... Then... you are done. You can see Windows Live Writer has detected the Orchard theme I am using After you finish with the blog post, click on Publish and refresh the Blog page in your Orchard website You see, we have the blog post directly posted from Windows Live Writer to my Orchard Blog. I hope this was useful blog post. Regards, Hajan Reference and other useful posts: Build incredible content-driven websites using Orchard CMS Create blog on your site with Orchard CMS Blogging using Windows Live Writer in your Orchard CMS Blog Orchard Website

  Read the article

• Online Judge System

  - by Deni Mf

  I'm planing to host a programing competition within my company, if the event is successful and there is a interest we plan to do this couple times a year. I've found the following self hosted platforms: http://www.domjudge.org/development http://sankhs.com/codejudge/ http://sharifjudge.ir/news/sharif-judge-12-released (does not support c#) And this online free service: http://www.codechef.com/hostyourcontest Can you share experience in hosting such event and what platforms did you used?

  Read the article

• Automapper: Handling NULL members

  - by PSteele

  A question about null members came up on the Automapper mailing list.  While the problem wasn’t with Automapper, investigating the issue led to an interesting feature in Automapper. Normally, Automapper ignores null members.  After all, what is there really to do?  Imagine these source classes: public class Source { public int Data { get; set; } public Address Address { get; set; } }   public class Destination { public string Data { get; set; } public Address Address { get; set; } }   public class Address { public string AddressType { get; set; } public string Location { get; set; } } And imagine a simple mapping example with these classes: Mapper.CreateMap<Source, Destination>();   var source = new Source { Data = 22, Address = new Address { AddressType = "Home", Location = "Michigan", }, };   var dest = Mapper.Map<Source, Destination>(source); The variable ‘dest’ would have a complete mapping of the Data member and the Address member. But what if the source had no address? Mapper.CreateMap<Source, Destination>();   var source = new Source { Data = 22, };   var dest = Mapper.Map<Source, Destination>(source); In that case, Automapper would just leave the Destination.Address member null as well.  But what if we always wanted an Address defined – even if it’s just got some default data?  Use the “NullSubstitute” option: Mapper.CreateMap<Source, Destination>() .ForMember(d => d.Address, o => o.NullSubstitute(new Address { AddressType = "Unknown", Location = "Unknown", }));   var source = new Source { Data = 22, };   var dest = Mapper.Map<Source, Destination>(source); Now, the ‘dest’ variable will have an Address defined with a type and location of “Unknown”.  Very handy! Technorati Tags: .NET,Automapper,NULL

  Read the article

• How to compile 'stygmorgan-0.29'?

  - by iwan

  I am trying to compile stygmorgan-0.29.tar.bz2 and got these messages: stygmorganui.cxx:7:28: fatal error: stygmicon128.xpm: No such file or directory compilation terminated. make[2]: *** [stygmorganui.o] Error 1 make[2]: Leaving directory `/home/papa/Downloads/stygmorgan-0.29/src' make[1]: *** [all] Error 2 make[1]: Leaving directory `/home/papa/Downloads/stygmorgan-0.29/src' make: *** [all-recursive] Error 1 papa@papa-G31-M7-TE:~/Downloads/stygmorgan-0.29$

  Read the article

• Introducing - TailspinSpyworks - WebForms Sample Application

  - by Latest Microsoft Blogs

  iBuySpy was a very popular sample application, but a lot has changed in Web Forms development since then. ScottGu suggested that I rewrite the old iBuySpy application – so I did. It’s ASP.NET 4 with CSS based layout, data access via Entity Framework, Read More......(read more)

  Read the article

• The penultimate audit trigger framework

  - by Piotr Rodak

  So, it’s time to see what I came up with after some time of playing with COLUMNS_UPDATED() and bitmasks. The first part of this miniseries describes the mechanics of the encoding which columns are updated within DML operation. The task I was faced with was to prepare an audit framework that will be fairly easy to use. The audited tables were to be the ones directly modified by user applications, not the ones heavily used by batch or ETL processes. The framework consists of several tables and procedures...(read more)

  Read the article

• Should we enforce code style in our large codebase?

  - by eighttrackmind

  By "code style" I mean 2 things: Style, eg. // bad if(foo){ ... } // good if (foo) { ... } Conventions and idiomaticity, where two ways of writing the same thing are functionally equivalent, but one is more idiomatic. eg. // bad if (fooLib.equals(a, b)) { ... } // good if (a == b) { ... } I think it makes sense to use an auto-formatter to enforce #1 automatically. So my question is specifically about #2. I like to break things down into pros and cons, here's what I've come up with so far: Pros: Used by many large codebases (eg. Google, jQuery) Helps make it a bit easier to work on new areas of the codebase Helps make code more portable (this is not necessarily true) Code style is automatic once you get used to it Makes it easier to fast-decline pull requests Cons: Takes engineers’ and code reviewers’ time away from more important things (like developing features) Code should ideally be rewritten every 2-3 years anyway, so it’s more important to focus on getting the architecture right, and achieving high test coverage Adds strain to code reviews (eg. “don’t do it this way, I like this other way better”) Even if I’ve been using a code style for a while, I still sometime have to pause and think about how to write a line better Having an enforced, uniform code style makes it hard to experiment with potentially better styles Maintaining a style guide takes a lot of incremental effort Engineers rarely read through the style guide. More often, it's cited in code reviews And as a secondary question: we also have many smaller repositories - should the same code style be enforced there?

  Read the article

• Dude, what’s up with POP Forums vNext?

  - by Jeff

  Yeah, it has been awhile. I posted v9.2 back in January, about five months ago. That’s a real change from the release pace I had there for awhile. Let me explain what’s going on. First off, in the interim, I re-launched CoasterBuzz, which required a lot of my attention for about two of those months. That’s a good thing though, because that site is just about the best test bed I could ask for. The other thing is that I committed to make the next version use ASP.NET MVC 4, which is now at the RC stage. I didn’t think much about when they’d hit their RTW point, but RC is good enough for me. To that end, there is enough change in the next version that I recently decided to make it a major version upgrade, and finish up the loose ends and science projects to make it whole. Here’s what’s in store… Mobile views: I sat on this or a long time. Originally, I was going to use jQuery Mobile, and waited and waited for a new release, but in the end, decided against using it. Sometimes buttons would unexplainably not work, I felt like I was fighting it at times, and the CSS just felt too heavy. I rolled my own mobile sugar at a fraction of the size, and I think you’ll find it easy to modify. And it’s Metro-y, of course! Re-do of background services: A number of things run in the background, and I did quite a bit of “reimagining” of that code. It’s the weirdness of running services in a Web site context, because so many folks can’t run a bona fide service on their host’s box. The biggest change here is that these service no longer start up by default. You’ll need to call a new method from global.asax called PopForumsActivation.StartServices(). This is also a precursor to running the app in a Web farm (new data layer and caching is the second part of that). I learned about this the hard way when I had three apps using the forum library code but only one was actually the forum. The services were all running three times as often with race conditions and hits on the same data. That was particularly bad for e-mail. CSS clean up: It’s still not ideal, but it’s getting better. That’s one of those things that comes with integrating to a real site… you discover all of the dumb things you did. The mobile CSS is particularly easier to live with. Bug fixes: There are a whole lot of them. Most were minor, but it’s feeling pretty solid now. So that’s where I am. I’m going to call it v10.0, and I’m going to really put forth some effort toward finishing the mobile experience and getting through the remaining bugs. The roadmap beyond that will likely not be feature oriented, but rather work on some other things, like making it run in Azure, perhaps using SQL CE, a better install experience, etc. As usual, I’ll post the latest here. Stay tuned!

  Read the article

• Distinguishing repetitive code with the same implementation

  - by KyelJmD

  Given this sample code import java.util.ArrayList; import blackjack.model.items.Card; public class BlackJackPlayer extends Player { private double bet; private Hand hand01 = new Hand(); private Hand hand02 = new Hand(); public void addCardToHand01(Card c) { hand01.addCard(c); } public void addCardToHand02(Card c) { hand02.addCard(c); } public void bustHand01() { hand01.setBust(true); } public void bustHand02() { hand02.setBust(true); } public void standHand01() { hand01.setStand(true); } public void standHand02() { hand02.setStand(true); } public boolean isHand01Bust() { return hand01.isBust(); } public boolean isHand02Bust() { return hand02.isBust(); } public boolean isHand01Standing() { return hand01.isStanding(); } public boolean isHand02Standing() { return hand02.isStanding(); } public int getHand01Score(){ return hand01.getCardScore(); } public int getHand02Score(){ return hand02.getCardScore(); } } Is this considered as a repetitive code? providing that each method is operating a seperate field but doing the same implementation ? Note that hand01 and hand02 should be distinct. if this is considered as repetitive code, how would I address this? providing that each hand is a seperate entity

  Read the article

• How does an optimizing compiler react to a program with nested loops?

  - by D.Singh

  Say you have a bunch of nested loops. public void testMethod() { for(int i = 0; i<1203; i++){ //some computation for(int k=2; k<123; k++){ //some computation for(int j=2; j<12312; j++){ //some computation for(int l=2; l<123123; l++){ //some computation for(int p=2; p<12312; p++){ //some computation } } } } } } When the above code reaches the stage where the compiler will try to optimize it (I believe it's when the intermediate language needs to converted to machine code?), what will the compiler try to do? Is there any significant optimization that will take place? I understand that the optimizer will break up the loops by means of loop fission. But this is only per loop isn't it? What I mean with my question is will it take any action exclusively based on seeing the nested loops? Or will it just optimize the loops one by one? If the Java VM complicates the explanation then please just assume that it's C or C++ code.

  Read the article

• MvcExtensions - PerRequestTask

  - by kazimanzurrashid

  In the previous post, we have seen the BootstrapperTask which executes when the application starts and ends, similarly there are times when we need to execute some custom logic when a request starts and ends. Usually, for this kind of scenario we create HttpModule and hook the begin and end request events. There is nothing wrong with this approach, except HttpModules are not at all IoC containers friendly, also defining the HttpModule execution order is bit cumbersome, you either have to modify the machine.config or clear the HttpModules and add it again in web.config. Instead, you can use the PerRequestTask which is very much container friendly as well as supports execution orders. Lets few examples where it can be used. Remove www Subdomain Lets say we want to remove the www subdomain, so that if anybody types http://www.mydomain.com it will automatically redirects to http://mydomain.com. public class RemoveWwwSubdomain : PerRequestTask { public RemoveWww() { Order = DefaultOrder - 1; } protected override TaskContinuation ExecuteCore(PerRequestExecutionContext executionContext) { const string Prefix = "http://www."; Check.Argument.IsNotNull(executionContext, "executionContext"); HttpContextBase httpContext = executionContext.HttpContext; string url = httpContext.Request.Url.ToString(); bool startsWith3W = url.StartsWith(Prefix, StringComparison.OrdinalIgnoreCase); bool shouldContinue = true; if (startsWith3W) { string newUrl = "http://" + url.Substring(Prefix.Length); HttpResponseBase response = httpContext.Response; response.StatusCode = (int)HttpStatusCode.MovedPermanently; response.Status = "301 Moved Permanently"; response.RedirectLocation = newUrl; response.SuppressContent = true; shouldContinue = false; } return shouldContinue ? TaskContinuation.Continue : TaskContinuation.Break; } } As you can see, first, we are setting the order so that we do not have to execute the remaining tasks of the chain when we are redirecting, next in the ExecuteCore, we checking the whether www is present, if present we are sending a permanently moved http status code and breaking the task execution chain otherwise we are continuing with the chain. Blocking IP Address Lets take another scenario, your application is hosted in a shared hosting environment where you do not have the permission to change the IIS setting and you want to block certain IP addresses from visiting your application. Lets say, you maintain a list of IP address in database/xml files which you want to block, you have a IBannedIPAddressRepository service which is used to match banned IP Address. public class BlockRestrictedIPAddress : PerRequestTask { protected override TaskContinuation ExecuteCore(PerRequestExecutionContext executionContext) { bool shouldContinue = true; HttpContextBase httpContext = executionContext.HttpContext; if (!httpContext.Request.IsLocal) { string ipAddress = httpContext.Request.UserHostAddress; HttpResponseBase httpResponse = httpContext.Response; if (executionContext.ServiceLocator.GetInstance<IBannedIPAddressRepository>().IsMatching(ipAddress)) { httpResponse.StatusCode = (int)HttpStatusCode.Forbidden; httpResponse.StatusDescription = "IPAddress blocked."; shouldContinue = false; } } return shouldContinue ? TaskContinuation.Continue : TaskContinuation.Break; } } Managing Database Session Now, let see how it can be used to manage NHibernate session, assuming that ISessionFactory of NHibernate is already registered in our container. public class ManageNHibernateSession : PerRequestTask { private ISession session; protected override TaskContinuation ExecuteCore(PerRequestExecutionContext executionContext) { ISessionFactory factory = executionContext.ServiceLocator.GetInstance<ISessionFactory>(); session = factory.OpenSession(); return TaskContinuation.Continue; } protected override void DisposeCore() { session.Close(); session.Dispose(); } } As you can see PerRequestTask can be used to execute small and precise tasks in the begin/end request, certainly if you want to execute other than begin/end request there is no other alternate of HttpModule. That’s it for today, in the next post, we will discuss about the Action Filters, so stay tuned.

  Read the article

• Internet Explorer 9 Cannot open file on download CTRL + J doesn’t work can’t open list of downloads

  - by simonsabin

  If any of the above symptoms are causing a problem, i.e. 1. You download a file and the download dialog disappears. 2. You select open when you download a file and nothing happens. 3. The View Downloads doesn’t work 4. CTRL + J doesn’t work (view downloads) The solution is to clear your download history See IE9 - View downloads / Ctrl+J do not open. I cannot open any file. But SAVE function still work fine. 64 bit version. for details the answer is provided by Steven. S on June 20th. I hope that...(read more)

  Read the article

• Which Opensource License i release my new Youtube video download Project so no one can ask me that this project is against youtube?

  - by John Smiith

  i have designed new opensource youtube video downloader but download videos from youtube is against youtube How can i make this type of message : This is opensource project that is used to download videos from youtube but downloading videos from youtube is against youtube and use of this project under study purpose only. Or Which Opensource License i release so that no one can ask me that this is against youtube?

  Read the article

• Digital Asset Management System

  - by Prashant

  I am looking for an opensource web-based digital asset management system. My requirements are to create a web based system where users can upload and download .zip, .jpg, .png, .pdf, .doc, .xls etc. media files. Also user management should be there, so that we can create multiple users and accordingly give them permissions. I have found one http://www.resourcespace.org/ but it looks a bit big and complicated. It is fitting to my need but I am looking and researching a bit more to get some good and more easy to use system. If anyone knows such web based system or tool, please share.

  Read the article

• How to use the Netduino Go Piezo Buzzer Module

  - by Chris Hammond

  Originally posted on ChrisHammond.com Over the next couple of days people should be receiving their Netduino Go Piezo Buzzer Modules , at least if they have ordered them from Amazon. I was lucky enough to get mine very quickly from Amazon and put together a sample project the other night. This is by no means a complex project, and most of it is code from the public domain for projects based on the original Netduino. Project Overview So what does the project do? Essentially it plays 3 “tunes” that...(read more)

  Read the article

• FGLRX does not have /usr/lib/libGL.so lib

  - by Paulo Lopes

  I am trying to compile some OpenGL apps from sources but there is no /usr/lib/libGL.so, or /usr/lib/libGL.so.1 or even /usr/lib/libGL.so.1.2. However fglrxinfo says: display: :0.0 screen: 0 OpenGL vendor string: ATI Technologies Inc. OpenGL renderer string: ATI Mobility Radeon HD 4500 Series OpenGL version string: 3.3.10237 Compatibility Profile Context Which is what i espect and the gears demo also works... How do i get those files? I tried the MESA files and then i got SW rendering which is not what i want...

  Read the article

• Why do you use not free software and what not free software do you use?

  - by 0101

  I prefer to use free software, because I believe its more universal(I can use it anywhere, I can tell people about it and they will have no problem with using it) - i like to say "learn once, use anywhere". I was wondering why people use not free software when free alternatives exists?(for example JIRA, Clover for code coverage, not free marge tools, etc.). P.S. I only use TotalCmd that is not free, but I was not able to find any good alternative(I even wrote one myself, but It was not as great). P.S. I dont want to start any flamewar, Im just curious what is your take on it.

  Read the article

• XSLT is not the solution you're looking for

  - by Jeff

  I was very relieved to see that Umbraco is ditching XSLT as a rendering mechanism in the forthcoming v5. Thank God for that. After working in this business for a very long time, I can't think of any other technology that has been inappropriately used, time after time, and without any compelling reason.The place I remember seeing it the most was during my time at Insurance.com. We used it, mostly, for two reasons. The first and justifiable reason was that it tweaked data for messaging to the various insurance carriers. While they all shared a "standard" for insurance quoting, they all had their little nuances we had to accommodate, so XSLT made sense. The other thing we used it for was rendering in the interview app. In other words, when we showed you some fancy UI, we'd often ditch the control rendering and straight HTML and use XSLT. I hated it.There just hasn't been a technology hammer that made every problem look like a nail (or however that metaphor goes) the way XSLT has. Imagine my horror the first week at Microsoft, when my team assumed control of the MSDN/TechNet forums, and we saw a mess of XSLT for some parts of it. I don't have to tell you that we ripped that stuff out pretty quickly. I can't even tell you how many performance problems went away as we started to rip it out.XSLT is not your friend. It has a place in the world, but that place is tweaking XML, not rendering UI.

  Read the article

< Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >