Search Results

Search found 21301 results on 853 pages for 'duplicate values'.

Page 778/853 | < Previous Page | 774 775 776 777 778 779 780 781 782 783 784 785  | Next Page >

• APC UPS replace battery light and apcupsd reporting "replace battery"

  - by mgjk

  We have an APC Smart UPS 1500. The "Replace Battery" light is on, and apcupsd reports: Emergency! Batteries have failed on UPS xxxx. Change them NOW However, from this article, http://sturgeon.apcc.com/kbasewb2.nsf/for+external/f39c4312fcaf7b948525679a005ebb78?OpenDocument it seems that it's not so clear that the UPS battery needs to be replaced. Stranger, according to the information on the UPS, an 11 minute runtime at 42.9% load running at 27.7V isn't so bad. Any thoughts about what to try next? We're a non-profit, money is an object. It would be a shame to replace a battery with a year or so left in it. # apcaccess status APC : 001,041,1017 DATE : Thu Mar 29 13:01:41 EDT 2012 HOSTNAME : oreilly2 VERSION : 3.14.6 (16 May 2009) debian UPSNAME : xxxx CABLE : Custom Cable Smart MODEL : Smart-UPS 1500 UPSMODE : Stand Alone STARTTIME: Thu Mar 29 12:57:30 EDT 2012 STATUS : ONLINE LINEV : 112.3 Volts LOADPCT : 42.9 Percent Load Capacity BCHARGE : 100.0 Percent TIMELEFT : 11.0 Minutes MBATTCHG : 5 Percent MINTIMEL : 3 Minutes MAXTIME : 0 Seconds OUTPUTV : 112.3 Volts SENSE : High DWAKE : -01 Seconds DSHUTD : 090 Seconds LOTRANS : 106.0 Volts HITRANS : 127.0 Volts RETPCT : 000.0 Percent ITEMP : 23.8 C Internal ALARMDEL : Always BATTV : 27.7 Volts LINEFREQ : 60.0 Hz LASTXFER : No transfers since turnon NUMXFERS : 0 TONBATT : 0 seconds CUMONBATT: 0 seconds XOFFBATT : N/A SELFTEST : NO STATFLAG : 0x07000008 Status Flag SERIALNO : AS0603298896 BATTDATE : 2006-01-14 NOMOUTV : 120 Volts NOMBATTV : 24.0 Volts FIRMWARE : 601.3.D USB FW:1.5 APCMODEL : Smart-UPS 1500 END APC : Thu Mar 29 13:02:12 EDT 2012 Error when running upstest You are using a SMART cable type, so I'm entering SMART test mode mode.type = USB_UPS Setting up the port ... Hello, this is the apcupsd Cable Test program. This part of apctest is for testing Smart UPSes. Please select the function you want to perform. 1) Query the UPS for all known values 2) Perform a Battery Runtime Calibration 3) Abort Battery Calibration 4) Monitor Battery Calibration progress 5) Program EEPROM 6) Enter TTY mode communicating with UPS 7) Quit Select function number: 2 First ensure that we have a good link and that the UPS is functionning normally. Simulating UPSlinkCheck ... YWrote: Y Got: getline failed. Apparently the link is not up. Giving up.

  Read the article

• Cannot exclude a path from basic auth when using a front controller script

  - by Adam Monsen

  I have a small PHP/Apache2 web application wherein I'd like to do two seemingly incompatible operations: Route all requests through a single PHP script (a "front controller", if you will) Secure everything except API calls with HTTP basic authentication I can satisfy either requirement just fine in isolation, it's when I try to do both at once that I am blocked. For no good reason I'm trying to accomplish these requirements solely with Apache configuration. Here are the requirements stated as an example. A GET request for this URL: http://basic/api/listcars?max=10 should be sent through front.php without requiring basic auth. front.php will get /api/listcars?max=10 and do whatever it needs to with that. Here's what I think should work. In my /etc/hosts I added 127.0.0.1 basic and I am using this Apache config: <Location /> AuthType Basic AuthName "Home Secure" AuthUserFile /etc/apache2/passwords require valid-user </Location> <VirtualHost *:80> ServerName basic DocumentRoot /var/www/basic <Directory /var/www/basic> <IfModule mod_rewrite.c> RewriteEngine On RewriteCond %{SCRIPT_FILENAME} !-f RewriteCond %{SCRIPT_FILENAME} !-d RewriteRule ^(.*)$ /front.php/$1 [QSA,L] </IfModule> </Directory> <Location /api> Order deny,allow Allow from all Satisfy any </Location> </VirtualHost> But I still always get a HTTP 401: Authorization Required response. I can make it work by changing <Location /api> into <Location ~ /api> but this allows more than I want to past basic auth. I also tried changing the <Directory /var/www/basic> section into <Location />, but this doesn't work either (and it results in some strange values for PATH_TRANSLATED being passed to the script). I searched around and found many examples of selective exclusion of basic auth, but none that also incorporated a front controller. I could certainly do something like handle basic auth in the front controller, but if I can have Apache do that instead I'll be able to keep all authentication logic out of my PHP code. A friend suggested splitting this into two vhosts, which I know also works. This used to be two separate vhosts, actually. I'm using Apache 2.2.22 / PHP 5.3.10 on Ubuntu 12.04.

  Read the article

• Error with postgres and Rails in Bundle Install on Ubuntu 12.10

  - by jason328

  I'm trying to install postgres onto Ubuntu. When running the Bundle Install in terminal I'm receiving this message at the end of the running code. How do I get pg to install properly? Libpq-dev is installed as well. Using coffee-rails (3.2.2) Using diff-lcs (1.1.3) Using jquery-rails (2.0.2) Installing pg (0.12.2) with native extensions Gem::Installer::ExtensionBuildError: ERROR: Failed to build gem native extension. /usr/bin/ruby1.9.1 extconf.rb checking for pg_config... yes Using config values from /usr/bin/pg_config checking for libpq-fe.h... yes checking for libpq/libpq-fs.h... yes checking for PQconnectdb() in -lpq... yes checking for PQconnectionUsedPassword()... yes checking for PQisthreadsafe()... yes checking for PQprepare()... yes checking for PQexecParams()... yes checking for PQescapeString()... yes checking for PQescapeStringConn()... yes checking for PQgetCancel()... yes checking for lo_create()... yes checking for pg_encoding_to_char()... yes checking for PQsetClientEncoding()... yes checking for rb_encdb_alias()... yes checking for rb_enc_alias()... no checking for struct pgNotify.extra in libpq-fe.h... yes checking for unistd.h... yes checking for ruby/st.h... yes creating extconf.h creating Makefile make compiling compat.c compiling pg.c pg.c: In function ‘pgconn_wait_for_notify’: pg.c:2117:3: warning: ‘rb_thread_select’ is deprecated (declared at /usr/include/ruby- 1.9.1/ruby/intern.h:379) [-Wdeprecated-declarations] pg.c: In function ‘pgconn_block’: pg.c:2592:3: error: format not a string literal and no format arguments [-Werror=format- security] pg.c:2598:3: warning: ‘rb_thread_select’ is deprecated (declared at /usr/include/ruby- 1.9.1/ruby/intern.h:379) [-Wdeprecated-declarations] pg.c:2607:4: error: format not a string literal and no format arguments [-Werror=format- security] pg.c: In function ‘pgconn_locreate’: pg.c:2866:11: warning: variable ‘lo_oid’ set but not used [-Wunused-but-set-variable] pg.c: In function ‘find_or_create_johab’: pg.c:3947:3: warning: implicit declaration of function ‘rb_encdb_alias’ [-Wimplicit- function-declaration] cc1: some warnings being treated as errors make: *** [pg.o] Error 1 Gem files will remain installed in /home/jason/.bundler/tmp/10083/gems/pg-0.12.2 for inspection. Results logged to /home/jason/.bundler/tmp/10083/gems/pg-0.12.2/ext/gem_make.out An error occurred while installing pg (0.12.2), and Bundler cannot continue. Make sure that `gem install pg -v '0.12.2'` succeeds before bundling.

  Read the article

• Mac OS X behind OpenLDAP and Samba

  - by Sam Hammamy

  I have been battling for a week now to get my Mac (Mountain Lion) to authenticate on my home network's OpenLDAP and Samba. From several sources, like the Ubuntu community docs, and other blogs, and after a hell of a lot of trial and error and piecing things together, I have created a samba.ldif that will pass the smbldap-populate when combined with apple.ldif and I have a fully functional OpenLDAP server and a Samba PDC that uses LDAP to authenticate the OS X Machine. The problem is that when I login, the home directory is not created or pulled from the server. I get the following in system.log Sep 21 06:09:15 Sams-MacBook-Pro.local SecurityAgent[265]: User info context values set for sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got user: sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got ruser: (null) Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got service: authorization Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_principal_for_user(): no authauth availale for user. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_principal_for_user(): failed: 7 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Failed to determine Kerberos principal name. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Done cleanup3 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Kerberos 5 refuses you Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): pam_sm_authenticate: ntlm Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_acct_mgmt(): OpenDirectory - Membership cache TTL set to 1800. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_record_check_pwpolicy(): retval: 0 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Establishing credentials Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Got user: sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Context initialised Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): pam_sm_setcred: ntlm user sam doesn't have auth authority All that's great and good and I authenticate. Then I get CFPreferences: user home directory for user kCFPreferencesCurrentUser at /Network/Servers/172.17.148.186/home/sam is unavailable. User domains will be volatile. Failed looking up user domain root; url='file://localhost/Network/Servers/172.17.148.186/home/sam/' path=/Network/Servers/172.17.148.186/home/sam/ err=-43 uid=9000 euid=9000 If you're wondering where /Network/Servers/IP/home/sam comes from, it's from a couple of blogs that said the OpenLDAP attribute apple-user-homeDirectory should have that value and the NFSHomeDirectory on the mac should point to apple-user-homeDirectory I also set the attr apple-user-homeurl to <home_dir><url>smb://172.17.148.186/sam/</url><path></path></home_dir> which I found on this forum. Any help is appreciated, because I'm banging my head against the wall at this point. By the way, I intend to create a blog on my vps just for this, and create an install script in python that people can download so no one has to go through what I've had to go through this week :) After some sleep I am going to try to login from a windows machine and report back here. Thanks Sam

  Read the article

• setting up a basic mod_proxy virtual host

  - by SevenProxies

  I'm trying to set up a basic virtual host to proxy all requests to test.local to a WEBrick server I have running on 127.0.0.1:8080 while keeping all requests to localhost going to my static files in /var/www. I'm running Ubuntu 10.04. I have libapache2-mod-proxy-html installed and I have the module enabled with a2enmod proxy. I also have my virtual host enabled. However, whenever I go to test.local I always get a cryptic 500 server error and all my logs are telling me is: [Thu Mar 03 01:43:10 2011] [warn] proxy: No protocol handler was valid for the URL /. If you are using a DSO version of mod_proxy, make sure the proxy submodules are included in the configuration using LoadModule. Here's my virtual host: <VirtualHost test.local:80> LoadModule proxy_module /usr/lib/apache2/modules/mod_proxy.so ServerAdmin webmaster@localhost ServerName test.local ProxyPreserveHost On # prevents this folder from being proxied ProxyPass /static ! DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> <Proxy *> Order allow,deny Allow from all </Proxy> ProxyPass / http://localhost:8080/ ProxyPassReverse / http://localhost:8080/ ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined and here's my settings for mod_proxy: <IfModule mod_proxy.c> #turning ProxyRequests on and allowing proxying from all may allow #spammers to use your proxy to send email. ProxyRequests Off <Proxy *> # default settings #AddDefaultCharset off #Order deny,allow #Deny from all ##Allow from .example.com AddDefaultCharset off Order allow,deny Allow from all </Proxy> # Enable/disable the handling of HTTP/1.1 "Via:" headers. # ("Full" adds the server version; "Block" removes all outgoing Via: headers) # Set to one of: Off | On | Full | Block ProxyVia On </IfModule> Does anybody know what I'm doing wrong? Thanks

  Read the article

• Why is user asked to choose their workgroup?

  - by Clinton Blackmore

  We running Mac OS X Server 10.5.8 with Mac OS X 10.5.8 clients. Students use network logins to, well, log in. I've been asked to deny internet access to a specific user. I was told that a good way to do it is to create a user workgroup called "No Internet Access" and manage settings there. (Specifically, I told parental controls to allow access to no sites, and blacklisted all the installed web browsers). Now, when the user authenticates to log in, they are greeted with this dialog: Workgroups for <username> Grade 7 Students No Internet Access It is unlikely that the student would willing choose "No Internet Access" to be their base group. Looking in Workgroup Manager at the student's record, it shows their primary group ID is the grade 7 group, and "No Internet Access" is listed as another group they belong to. I looked at the managed preferences for all the computers pertaining to logins. They are set to their defaults. Specifically, the computer groups' preference for Logins - Access has the defaults: [unchecked] Ignore workgroup nesting [checked] Combine available workgroup settings Based on my reading of Tips and Tricks for Mac Administrators, this should be correct, the user should not be asked which group they belong to, and settings from all applicable groups should be applied. How can I achieve that result? Edit: I've decided to add some additional information from the Tips and Tricks for Mac Management White Paper (via Apple in Education, via the author's site). On page 21, it says: With Leopard MCX, workgroup preference settings are combined by default into a single set of values. This means that instead of having to choose between the Math, Science, or Language Arts workgroups when logging in, a user can just authenticate and be taken directly to the desktop. All the settings for each of those workgroups are composited together, providing you with all the Dock items and a composite of all the other settings. On page 40, an example is given in which settings are combined from different 'domains', one computer group, two (user) workgroups, and one individual user's settings. [When johnd logs into a leopard client,] the items staged in the Dock from left to right are: computer group, first workgroup alphabetically, second workgroup, user. Items within the workgroup are staged alphabetically. Nowhere is there an indication that groups are nested; indeed, I can see no sensible (non-flat) heirarchy for groups like Math, Science, and Language Arts. I strongly believe that there is a way to apply settings from two unrelated user workgroups such that a user of OS X 10.5.x or newer does not need to choose their workgroup. This is what I seek to achieve.

  Read the article

• Apache2 & .htaccess : Apache ignoring AccessFile

  - by Elyx0

  Hi there here is my server configuration: DEBIAN 32Bits / PHP 5 / Apache Server version: Apache/2.2.3 - Server built: Mar 22 2008 09:29:10 The AccessFiles : grep -ni AccessFileName * apache2.conf:134:AccessFileName .htaccess apache2.conf:667:AccessFileName .httpdoverride All the AllowOverride statements in my apache2/ folder. mods-available/userdir.conf:6: AllowOverride Indexes AuthConfig Limit mods-available/userdir.conf:16: AllowOverride FileInfo AuthConfig Limit mods-enabled/userdir.conf:6: AllowOverride Indexes AuthConfig Limit mods-enabled/userdir.conf:16: AllowOverride FileInfo AuthConfig Limit sites-enabled/default:8: AllowOverride All sites-enabled/default:14: AllowOverride All sites-enabled/default:19: AllowOverride All sites-enabled/default:24: AllowOverride All sites-enabled/default:42: AllowOverride All The sites-enabled/default file : 1 <VirtualHost *> 2 ServerAdmin [email protected] 3 ServerName mysite.com 4 ServerAlias mysite.com 5 DocumentRoot /var/www/mysite.com/ 6 <Directory /> 7 Options FollowSymLinks 8 AllowOverride All 9 Order Deny,Allow 10 Deny from all 11 </Directory> 12 <Directory /var/www/mysite.com/> 13 Options Indexes FollowSymLinks MultiViews 14 AllowOverride All 15 Order allow,deny 16 allow from all 17 </Directory> 18 <Directory /var/www/mysite.com/test/> 19 AllowOverride All 20 </Directory> 21 22 ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ 23 <Directory "/usr/lib/cgi-bin"> 24 AllowOverride All 25 Options ExecCGI -MultiViews +SymLinksIfOwnerMatch 26 Order allow,deny 27 Allow from all 28 </Directory> 29 30 ErrorLog /var/log/apache2/error.log 31 32 # Possible values include: debug, info, notice, warn, error, crit, 33 # alert, emerg. 34 LogLevel warn 35 36 CustomLog /var/log/apache2/access.log combined 37 ServerSignature Off 38 39 Alias /doc/ "/usr/share/doc/" 40 <Directory "/usr/share/doc/"> 41 Options Indexes MultiViews FollowSymLinks 42 AllowOverride All 43 Order deny,allow 44 Deny from all 45 Allow from 127.0.0.0/255.0.0.0 ::1/128 46 </Directory> 47 48 49 50 51 52 53 54 </VirtualHost> If i change any Allow from all in Deny from all , it works whenever i put it. I've got one .htaccess at /mysite.com/.htaccess & one at /mysite.com/test/.htaccess with: Order Deny,Allow Deny from all Neither of them work i can still see my website. I've got mod_rewrite enabled but i don't think it does anything here. I've tried almost everything :/ It works on my local environnement (MAMP) but fails when on my Debian server.

  Read the article

• long access times and errors in iis application

  - by user55862

  I am having an issue with an IIS application (details of environment at the end of the message). The web site works great most of the time and I cannot reproduce any error in our test system. On the live system however with on averare of 5-15 requests per second I have a problem with that some requests (about 0.05%) will take over 300 seconds to complete. The other requests complete withing 5-10 seconds. It seem like if all the errornous requests end up with a Timer_EntityBody error in the error log. I have never seen this as an end user but I guess that they will receive some kind of error message. I am trying to find out what can be causing this errornous behaviour. Any ideas are welcome. I have read something about that there can be an MTU issue if ICMP and MTU protocols are blocked in the firewall. Does that sound reasonable? I have also read about updating to IIS 7 should do the trick. Does it sound reasonable? I think that the problem has another cause but I have no idea of what. I have tried running hte perormance monitor, monitoring for database locks and active transaction counts. I can see some of these in the perfmon log for the MSSQL server (another machine) for example: Active transactions is sometimes peaking and sometimes for long periods Lock waits per seconds is sometimes peaking Transactions per second is sometimes peaking Page IO Latch wait is sometimes peaking Lock wait time (ms) is sometimes peaking But I cannot see that any of these correlate to the errors in the IIS error log. On the IIS server machine I can also see with perfmon that some values peak a few times during a day: Request execution time Avg disk queue length I can neither see that any of these correlate to the errors in the IIS error log. In the below code I have anonymized by replacing some parts with HIDDEN The following can be seen in the access log 2010-10-01 08:35:05 W3SVC1301873091 **HIDDEN** POST /**HIDDEN**/Modules/BalanceModule.aspx - 80 - **HIDDEN** Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+5.1;+.NET+CLR+2.0.50727;+.NET+CLR+3.0.4506.2152;+.NET+CLR+3.5.30729;+.NET4.0C;+.NET4.0E) ASP.NET_SessionId=**HIDDEN** 400 0 64 0 2241 127799 At the same time the following can be seen in the error log: 2010-10-01 08:35:05 **HIDDEN** 1999 **HIDDEN** 80 HTTP/1.0 POST /**HIDDEN**/Modules/BalanceModule.aspx - 1301873091 Timer_EntityBody Test+Pool I can tell the following about the environment: Server: Windows Server 2003 x64 SP2 running on VMWare HTTP Server: IIS v6.0 with ASP.NET 2.0.50727 Antivirus: Trend Micro OfficeScan (Is it a good idea to have this on a server?)

  Read the article

• How to correctly partition usb flash drive and which filesystem to choose considering wear leveling?

  - by random1

  Two problems. First one: how to partition the flash drive? I shouldn't need to do this, but I'm no longer sure if my partition is properly aligned since I was forced to delete and create a new partition table after gparted complained when I tried to format the drive from FAT to ext4. The naive answer would be to say "just use default and everything is going to be alright". However if you read the following links you'll know things are not that simple: https://lwn.net/Articles/428584/ and http://linux-howto-guide.blogspot.com/2009/10/increase-usb-flash-drive-write-speed.html Then there is also the issue of cylinders, heads and sectors. Currently I get this: $sfdisk -l -uM /dev/sdd Disk /dev/sdd: 30147 cylinders, 64 heads, 32 sectors/track Warning: The partition table looks like it was made for C/H/S=*/255/63 (instead of 30147/64/32). For this listing I'll assume that geometry. Units = mebibytes of 1048576 bytes, blocks of 1024 bytes, counting from 0 Device Boot Start End MiB #blocks Id System /dev/sdd1 1 30146 30146 30869504 83 Linux $fdisk -l /dev/sdd Disk /dev/sdd: 31.6 GB, 31611420672 bytes 255 heads, 63 sectors/track, 3843 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00010c28 So from my current understanding I should align partitions at 4 MiB (currently it's at 1 MiB). But I still don't know how to set the heads and sectors properly for my device. Second problem: file system. From the benchmarks I saw ext4 provides the best performance, however there is the issue of wear leveling. How can I know that my Transcend JetFlash 700's microcontroller provides for wear leveling? Or will I just be killing my drive faster? I've seen a lot of posts on the web saying don't worry the newer drives already take care of that. But I've never seen a single piece of backed evidence of that and at some point people start mixing SSD with USB flash drives technology. The safe option would be to go for ext2, however a serious of tests that I performed showed horrible performance!!! These values are from a real scenario and not some synthetic test: 42 files: 3,429,415,284 bytes copied to flash drive original fat32: 15.1 MiB/s ext4 after new partition table: 10.2 MiB/s ext2 after new partition table: 1.9 MiB/s Please read the links that I posted above before answering. I would also be interested in answers backed up with some references because a lot is said and re-said but then it lacks facts. Thank you for the help.

  Read the article

• order of operations for environment variables

  - by alyda

  I want to understand how environment variables are set and reset (overridden). I'm running Apache/2.2.24 (Unix) PHP/5.4.14 on a mac . My theory is this: Environment vars can be set in bash, then they can be overwritten with httpd.conf preceding a VirtualHost directive that precedes php.ini, which can then be overwritten by .htaccess (if allowable) and finally by PHP I tried the following: setting environment variable in bash: I added export ENVIRONMENT='local' to my ~/.bashrc file, restarted apache and did not get any output from print_r($_ENV); (in a simple index.php file at the root of my webserver). I also tried putting ENVIRONMENT='local' into /etc/environment, and restarting apache, nothing, as well as /etc/bashrc, restart apache. still nothing. setting environment variable in httpd.conf: I added SetEnv ENVIRONMENT 'local-httpd to the end of my /etc/apache2/httpd.conf file (but before I load other conf files, such as virtual host [Include /private/etc/apache2/other/*.conf]). I now see the variable in the array print_r($_SERVER); but not print_r($_ENV);. setting environment variable in httpd-vhosts.conf: I added SetEnv ENVIRONMENT 'local-vhost to my /etc/apache2/extra/httpd-vhosts.conf file in my generic directive that points to my default document root. I now see the variable has been overwritten (to local-vhost from local-httpd, so I know where the variable is getting set). setting environment variable in php.ini: while searching for a proper place to put my environment variable, I noticed that variables_order = "GPCS" was set to the production value rather than EGPCS. I changed it, restarted my server and found that I was now getting output for print_r($_ENV); but not my expected custom variable. It also appears that I am not able to set a custom variable in this file. Please tell me if I am wrong setting environment variable in .htaccess: I added SetEnv ENVIRONMENT 'local-htaccess'. This worked as expected, overwriting all other values that were set. setting / overwriting environment variable in PHP: if (...) { putenv('ENVIRONMENT=local'); } I'm asking this question because I have a lot of local and remote testing servers, some of which may or may not allow me access to modify httpd, httpd-vhost, php.ini or environment variables. I want to understand what is best for those difference scenarios (shared hosting, heroku, local servers, etc) I obviously don't know how to properly set the environment variable in bash in a way that php can use it, I'd like to know how to do that (as I think Heroku does something similar with heroku config set...)

  Read the article

• Setting Timeouts: SQL Server 2008/IIS 7.5

  - by Julie

  We have recently migrated from a Win 2003/SQL Server 2000 system to Win 2008 64 bit R2, SQL Server 2008 R2. Our websites are in classic asp, and this can't be changed to another scripting language at this time. On the old server, if I got stuck in some kind of endless loop, the page would throw an error. On the new server, I have a page that has some sort of looping problem, that even though the SQL SP is called only once (and runs fine run as a query on the server) it pegs SQL server and therefore locks all of our websites. I'll get my code figured out, no biggie. But I need to make sure the server times out when this happens. (The page I'm working on runs fine with certain instances of the query, and locks with others using a different query variable. I can't have something like that sneak up on me on a page I haven't touched for three years.) I can't figure out how an SP that runs once on the server, from an ASP page, is tying up SQL server this way. It's obviously some sort of a timeout issue, but I can't figure out where/which timeout values to change. I actually have to remote desktop to the server and kill the process in SQL server. I'm afraid I'm a generalist, and server management is not my thing, even though it's my responsibility, so I am almost certain to have questions about any answer that I receive. How can I track this down? What settings do I need to change? More info: It's not SQL Server On our test site, I created an ASP file that just did an endless loop (do while 1=1) and had the same problem - the other websites wouldn't load - without SQL server being involved. So I think the reason the process was hanging is that the page wasn't timing out as it should, and so the connection to SQL was never closed. Killing the process in SQL server would reset the page somehow. For my intentional endless loop, I had to refresh the app pool to get rid of it. This points more to either IIS or the ASP settings. The ASP timeouts are set to whatever the default were when the server was first loaded. I still can't figure out why one file is locking up all websites, though. Again, that didn't happen on the old server.

  Read the article

• radvd is not assigning prefix

  - by Samik

  I'm currently trying to setup IPv6 address auto-configuration with router advertisement daemon (radvd) on a virtual machine running CentOS 6.5. But the eth0 interface is not obtaining that prefix. I've obtained the ULA prefix from here. Contents of /etc/sysctl.conf # Kernel sysctl configuration file for Red Hat Linux # # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and # sysctl.conf(5) for more details. # Controls IP packet forwarding net.ipv4.ip_forward = 0 net.ipv6.conf.all.forwarding = 1 # Controls source route verification net.ipv4.conf.default.rp_filter = 1 # Do not accept source routing net.ipv4.conf.default.accept_source_route = 0 # Controls the System Request debugging functionality of the kernel kernel.sysrq = 0 # Controls whether core dumps will append the PID to the core filename. # Useful for debugging multi-threaded applications. kernel.core_uses_pid = 1 # Controls the use of TCP syncookies net.ipv4.tcp_syncookies = 1 # Disable netfilter on bridges. net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 # Controls the default maxmimum size of a mesage queue kernel.msgmnb = 65536 # Controls the maximum size of a message, in bytes kernel.msgmax = 65536 # Controls the maximum shared segment size, in bytes kernel.shmmax = 68719476736 # Controls the maximum number of shared memory segments, in pages kernel.shmall = 4294967296 Contents of /etc/radvd.conf # NOTE: there is no such thing as a working "by-default" configuration file. # At least the prefix needs to be specified. Please consult the radvd.conf(5) # man page and/or /usr/share/doc/radvd-*/radvd.conf.example for help. # # interface eth0 { AdvSendAdvert on; MinRtrAdvInterval 3; MaxRtrAdvInterval 10; AdvDefaultPreference low; AdvHomeAgentFlag off; prefix fd8a:8d9d:808f:1::/64 { AdvOnLink on; AdvAutonomous on; AdvRouterAddr on; }; }; Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes I've also enabled radvd at startup through chkconfig. Though I noticed that radvd is starting after interfaces are brought up. I've tried restarting the network service afterwards but still I get the following link-local address only #ip -6 addr show 1: lo: mtu 16436 inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qlen 1000 inet6 fe80::5054:ff:fe74:d746/64 scope link valid_lft forever preferred_lft forever Edit: Based on the answer given by Sander Steffann I still need clarification on some points but I'm posting here what worked. Contents of /etc/sysconfig/network NETWORKING=yes HOSTNAME=syslog-ng-server NETWORKING_IPV6=yes IPV6FORWARDING=yes Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes IPV6FORWARDING=no Removed following line from /etc/sysctl.conf net.ipv6.conf.all.forwarding = 1 Contents of /etc/radvd.conf is as previous.

  Read the article

• JavaMail application won't send email to external SMTP server

  - by Luiz Cruz

  This is actually a question from an exam, but I believe it could help others troubleshooting a similar situation. In a system, an e-mail needs to be sent to a certain mailbox. The following Java code, which is part of a larger system, was developed for that. Assume that "example.com" corresponds to a valid registered internet domain. public void sendEmail(){ String s1=”Warning”; String b1=”Contact IT support.”; String r1=”[email protected]”; String d1=”[email protected]”; String h1=”mx.intranet”; Properties p1 = new Properties(); p1.put(“mail.host”, h1); Session session = Session.getDefaultInstance(p1, null); MimeMessage message = new MimeMessage(session); try { message.setFrom(new InternetAddress(r1)); message.addRecipient(Message.RecipientType.TO, new InternetAddress(d1)); message.setSubject(s1); message.setText(b1); Transport.send(message); } catch (MessagingException e){ System.err.println(e); } } The execution of this code, within the testing environment of an application server, does NOT work as expected. The mailbox of the "example.com" server never receives the email, even tough all string values in the code are correctly attributed. The output for the command "netstat -np TCP" in the application server during execution is shown bellow: Src Add Src Port Dest Add Dest Port State 192.168.5.5 54395 192.168.7.1 25 SYN_SENT 192.168.5.5 54390 192.168.7.1 110 TIME_WAIT 192.168.5.5 52001 200.218.208.118 80 CLOSE_WAIT 192.168.5.5 52050 200.218.208.118 80 ESTABLISHED 192.168.5.5 50001 200.255.94.202 25 TIME_WAIT 192.168.5.5 50000 200.255.94.202 25 ESTABLISHED With the exception of the lines that were NAT'd, all others are associated with the Java application server, which created them after the execution of the code above. The e-mail server used in this environment is the production server, which is online and does not require any authentication for internal connections. Based on this situation, point out three possible causes for the problem.

  Read the article

• Windows 8.1 IRQL_NOT_LESS_OR_EQUAL with Asus PCE-n53

  - by JArsenault89

  I saw the following question, and it is the exact same problem on my machine, I have tracked it to the ASUS PCE-n53 wireless card in my desktop. Does anyone know of a workaround? Windows 8.1 RTM installation crashes The adapter worked fine in windows 8... any ideas? EDIT: Crash Dump Analysis * Bugcheck Analysis * * IRQL_NOT_LESS_OR_EQUAL (a) An attempt was made to access a pageable (or completely invalid) address at an interrupt request level (IRQL) that is too high. This is usually caused by drivers using improper addresses. If a kernel debugger is available get the stack backtrace. Arguments: Arg1: 0000000000000000, memory referenced Arg2: 0000000000000002, IRQL Arg3: 0000000000000001, bitfield : bit 0 : value 0 = read operation, 1 = write operation bit 3 : value 0 = not an execute operation, 1 = execute operation (only on chips which support this level of status) Arg4: fffff801ef4f1316, address which referenced memory Debugging Details: WRITE_ADDRESS: 0000000000000000 CURRENT_IRQL: 2 FAULTING_IP: nt!KeReleaseSpinLock+16 fffff801`ef4f1316 f048832100 lock and qword ptr [rcx],0 DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT BUGCHECK_STR: AV PROCESS_NAME: System ANALYSIS_VERSION: 6.3.9600.16384 (debuggers(dbg).130821-1623) amd64fre TRAP_FRAME: ffffd00020d45550 -- (.trap 0xffffd00020d45550) NOTE: The trap frame does not contain all registers. Some register values may be zeroed or incorrect. rax=0000000000000001 rbx=0000000000000000 rcx=0000000000000000 rdx=0000000055920200 rsi=0000000000000000 rdi=0000000000000000 rip=fffff801ef4f1316 rsp=ffffd00020d456e0 rbp=ffffd00020d45768 r8=0000000055920222 r9=0000000035930000 r10=0000000055920222 r11=ffffd00020d456a8 r12=0000000000000000 r13=0000000000000000 r14=0000000000000000 r15=0000000000000000 iopl=0 nv up ei pl zr na po nc nt!KeReleaseSpinLock+0x16: fffff801ef4f1316 f048832100 lock and qword ptr [rcx],0 ds:0000000000000000=???????????????? Resetting default scope LOCK_ADDRESS: fffff801ef6da360 -- (!locks fffff801ef6da360) Resource @ nt!PiEngineLock (0xfffff801ef6da360) Exclusively owned Contention Count = 6 Threads: ffffe000010ff040-01<* 1 total locks, 1 locks currently held PNP_TRIAGE: Lock address : 0xfffff801ef6da360 Thread Count : 1 Thread address: 0xffffe000010ff040 Thread wait : 0x1fbe LAST_CONTROL_TRANSFER: from fffff801ef5647e9 to fffff801ef558ca0 STACK_TEXT: ffffd00020d45408 fffff801ef5647e9 : 000000000000000a 0000000000000000 0000000000000002 0000000000000001 : nt!KeBugCheckEx ffffd00020d45410 fffff801ef56303a : 0000000000000001 0000000000000000 ffff0c83e3e25300 ffffd00020d45550 : nt!KiBugCheckDispatch+0x69 ffffd00020d45550 fffff801ef4f1316 : 00000000000a5890 0000000000000001 0000000000000000 ffffe00004c00000 : nt!KiPageFault+0x23a ffffd00020d456e0 fffff80003b430ad : 00000000000afe80 ffffe00004c00000 00000000000a2f80 0000000035720000 : nt!KeReleaseSpinLock+0x16 ffffd00020d45710 fffff80003ac249f : ffffe00004c00000 00000000000000a8 ffffe00004c85050 0000000000000800 : netr28x+0x840ad ffffd00020d457b0 fffff80000b76475 : ffffd00020d459e8 ffffd00020d459f0 ffffe00004ac2006 ffffe00004ac21a0 : netr28x+0x349f ffffd00020d459a0 fffff80000baa248 : ffffe00004ac2eb8 0000000000000000 ffffe00000000000 ffffe00004ac21a0 : ndis!ndisMInvokeInitialize+0x39 ffffd00020d459e0 fffff80000b74784 : 0000000000000050 ffffe00004907ba0 0000000000000000 01cecbbc328e6cde : ndis!ndisMInitializeAdapter+0x4dc ffffd00020d46050 fffff80000b74d3d : 0000000000000050 ffffe0000443e770 ffffc00000951480 ffffe00004ac21a0 : ndis!ndisInitializeAdapter+0x60 ffffd00020d460a0 fffff80000b74c14 : ffffe00004ac21a0 ffffe00004ac2050 ffffe000047ec2a0 0000000000000000 : ndis!ndisPnPStartDevice+0x89 ffffd00020d460f0 fffff80000b87695 : ffffe00004ac21a0 ffffe00004ac21a0 ffffd00020d461b0 ffffe000047ec2a0 : ndis!ndisStartDeviceSynchronous+0x58 ffffd00020d46140 fffff80000b6a760 : ffffe000047ec2a0 ffffe00004ac21a0 0000000000000000 0000000000000000 : ndis!ndisPnPIrpStartDevice+0x13471 ffffd00020d46170 fffff8000032576c : ffffe00004b11501 ffffe00004b11570 0000000000000001 fffff80000325880 : ndis!ndisPnPDispatch+0x140 ffffd00020d461e0 fffff8000030b40a : ffffe000047ec2a0 0000000000000106 ffffd00020d462f0 ffffe00004b116c0 : Wdf01000!FxPkgFdo::PnpSendStartDeviceDownTheStackOverload+0xe8 ffffd00020d46250 fffff80000305942 : 0000000000000106 ffffd00020d462f0 0000000000000105 ffffd00020d464d0 : Wdf01000!FxPkgPnp::PnpEventInitStarting+0xa ffffd00020d46280 fffff80000305a5a : ffffe00004b116c8 0000000000000002 ffffe00004b11570 ffffe00004b11600 : Wdf01000!FxPkgPnp::PnpEnterNewState+0x102 ffffd00020d46310 fffff80000305bc4 : 0000000000000000 ffffd00020d46400 ffffe00004b116a0 0000000000000000 : Wdf01000!FxPkgPnp::PnpProcessEventInner+0xc2 ffffd00020d46390 fffff8000030c27a : 0000000000000000 ffffe00004b11570 0000000000000000 ffffe00004b11570 : Wdf01000!FxPkgPnp::PnpProcessEvent+0xe4 ffffd00020d46430 fffff80000300936 : ffffe00004b11570 ffffd00020d464c0 0000000000000000 ffffe00004a0e630 : Wdf01000!FxPkgPnp::_PnpStartDevice+0x1e ffffd00020d46460 fffff800002fba18 : ffffe000047ec2a0 ffffe000047ec2a0 0000000000000000 ffffe0000486f020 : Wdf01000!FxPkgPnp::Dispatch+0xd2 ffffd00020d464d0 fffff801ef838796 : 0000000000000000 fffff801ef6aa101 0000000000000000 ffffd000208aa180 : Wdf01000!FxDevice::DispatchWithLock+0x7d8 ffffd00020d465b0 fffff801ef4d5bad : ffffe000011dc3a0 ffffd00020d46659 0000000000000000 fffff801ef7f5ba4 : nt!PnpAsynchronousCall+0x102 ffffd00020d465f0 fffff801ef838e57 : ffffe000011db8d0 ffffe000011db8d0 ffffe00004a8d060 ffffc00002b11200 : nt!PnpStartDevice+0xc5 ffffd00020d466c0 fffff801ef838fe7 : ffffe000011db8d0 ffffe000011db8d0 0000000000000000 ffffe000011db8d0 : nt!PnpStartDeviceNode+0x147 ffffd00020d46790 fffff801ef7fd19e : ffffe000011db8d0 0000000000000001 0000000000000001 ffffe00000000001 : nt!PipProcessStartPhase1+0x53 ffffd00020d467d0 fffff801ef897b17 : ffffe000011db8d0 0000000000000001 0000000000000000 fffff801ef7ef7b2 : nt!PipProcessDevNodeTree+0x3ce ffffd00020d46a50 fffff801ef4f5033 : 0000000100000003 0000000000000000 0000000000000000 0000000000000000 : nt!PiRestartDevice+0xaf ffffd00020d46aa0 fffff801ef44565d : fffff801ef4f4c90 ffffd00020d46bd0 0000000000000000 ffffe00004a10170 : nt!PnpDeviceActionWorker+0x3a3 ffffd00020d46b50 fffff801ef4eec80 : 0000000000000000 ffffe000010ff040 ffffe000010ff040 ffffe0000035c900 : nt!ExpWorkerThread+0x2b5 ffffd00020d46c00 fffff801ef55f2c6 : ffffd00020472180 ffffe000010ff040 ffffe00000608040 ffffc00000002710 : nt!PspSystemThreadStartup+0x58 ffffd00020d46c60 0000000000000000 : ffffd00020d47000 ffffd00020d41000 0000000000000000 0000000000000000 : nt!KiStartSystemThread+0x16 STACK_COMMAND: kb FOLLOWUP_IP: netr28x+840ad fffff800`03b430ad 4533e4 xor r12d,r12d SYMBOL_STACK_INDEX: 4 SYMBOL_NAME: netr28x+840ad FOLLOWUP_NAME: MachineOwner MODULE_NAME: netr28x IMAGE_NAME: netr28x.sys DEBUG_FLR_IMAGE_TIMESTAMP: 51de7a8d FAILURE_BUCKET_ID: AV_netr28x+840ad BUCKET_ID: AV_netr28x+840ad ANALYSIS_SOURCE: KM FAILURE_ID_HASH_STRING: km:av_netr28x+840ad FAILURE_ID_HASH: {a1f86ced-f566-ac23-afeb-1aa88ea5ab8f} Followup: MachineOwner

  Read the article

• PHP & MySQL on Mac OS X: Access denied for GUI user

  - by Eirik Lillebo

  Hey! This question was first posted to Stack Overflow, but as it is perhaps just as much a server issue I though it might be just as well to post it here also. I have just installed and configured Apache, MySQL, PHP and phpMyAdmin on my Macbook in order to have a local development environment. But after I moved one of my projects over to the local server I get a weird MySQL error from one of my calls to mysql_query(): Access denied for user '_securityagent'@'localhost' (using password: NO) First of all, the query I'm sending to MySQL is all valid, and I've even testet it through phpMyAdmin with perfect result. Secondly, the error message only happens here while I have at least 4 other mysql connections and queries per page. This call to mysql_query() happens at the end of a really long function that handles data for newly created or modified articles. This basically what it does: Collect all the data from article form (title, content, dates, etc..) Validate collected data Connect to database Dynamically build SQL query based on validated article data Send query to database before closing the connection Pretty basic, I know. I did not recognize the username "_securityagent" so after a quick search I came across this from and article at Apple's Developer Connection talking about some random bug: Mac OS X's security infrastructure gets around this problem by running its GUI code as a special user, "_securityagent". Then I tried put a var_dump() on all variables used in the mysql_connect() call, and every time it returns the correct values (where username is not "_securityagent" of course). Thus I'm wondering if anyone has any idea why 'securityagent' is trying to connect to my database - and how I can keep this error from occurring when I call mysql_query(). Update: Here is the exact code I'm using to connect to the database. But a little explanation must follow: The connection error happens at a call to mysql_query() in function X in class_1 class_1 uses class_2 to connect to database class_2 reads a config file with the database connection variables (host, user, pass, db) class_2 connect to the database through the following function: var $SYSTEM_DB_HOST = ""; function connect_db() { // Reads the config file include('system_config.php'); if (!($SYSTEM_DB_HOST == "")) { mysql_connect($SYSTEM_DB_HOST, $SYSTEM_DB_USER, $SYSTEM_DB_PASS); @mysql_select_db($SYSTEM_DB); return true; } else { return false; } }

  Read the article

• Windows 7 fails to install on KVM with qemu

  - by kief_morris

  I'm trying to install Windows 7 on a virtual machine on my 64 bit Ubuntu Karmic box. I get to the point of selecting my language settings and clicking 'install now', but a short while later I get a blue screen of death. I've tried a few variations, including using the 32 bit (fails very quickly). The virt-install command I've tried includes this: sudo virt-install --connect qemu:///system -n ksm-win7 -r 2048 \ --disk path=/home/kief/VM-Images/ksm-win7.qcow2,size=50 \ -c /var/Software/Windows7/Full/64bit/SW_DVD5_SA_Win_Ent_7_64BIT_English_Full_MLF_X15-70749.ISO \ --vnc --os-type windows --os-variant vista --hvm The limited info I could find suggested that 'vista' should work as the --os-variant, I haven't found any values specific to windows 7. Here's my blue screen: I've found very little by Googling, so I'm guessing this isn't a case of KVM simply not supporting Windows 7. Thanks for any help. Update: I have been able to successfully create a Windows 7 VM using the graphical "Virtual Machine Manager" app, although I don't really understand the cause of the problem with the VM created with virt-install. Comparing the configuration files under /etc/libvirt/qemu provides some clues, although I don't know enough to interpret them properly. The interesting differences in the two VM configurations are: --- win7-virt-install.xml +++ win7-vmm.xml -<domain type='qemu'> +<domain type='kvm'> @@ -21 +21 @@ - <emulator>/usr/bin/qemu-system-x86_64</emulator> + <emulator>/usr/bin/kvm</emulator> @@ -23 +23 @@ - <source file='/home/kief/VM-Images/ksm-win7.qcow2'/> + <source file='/var/lib/libvirt/images/ksm-win7x64.img'/> I'm not sure if this means the working VM is not using qemu at all, or if there is some other difference in the way it's used with kvm. Update2: So I've answered my own question (mostly) below. A KVM VM needs to use KVM's own CPU emulation rather than qemu's in order for me to get Windows 7 installed. I'm not sure whether there is something that can be done to get it working on a qemu-emulation CPU, or whether a newer version will support it. But at least it is possible to get it running on a KVM VM.

  Read the article

• Varnish + Plesk : vhost broken

  - by Raphaël

  I have an e-commerce site with 300,000 products and 20,000 categories. It is slow and currently in production. I decided to install Varnish to speed up. The trouble is that during installation, I got a Guru Meditation. Since the site is in production, I am not allowed to leave this error more than a second, thinking to have made an enormous stupidity. I followed the following tutorial: http://www.euperia.com/linux/setting-up-varnish-with-apache-tutorial I'm sure I followed all without error. I say that there may be a specific configuration with plesk. Has anyone already installed Varnish on a ubuntu 11.04 server with plesk 10? Does anyone have a better resource? I know it is "very vague" as an error, but maybe some of you have had this problem. edit 24/11/2011 I continued to work on Varnish + Plesk ... but it still does not work. 1) I changed the port for apache in plesk General # mysql -uadmin -p`cat /etc/psa/.psa.shadow` -D psa -e'replace into misc (param, val) values ("http_port", 8008)' 1.1) I rebuild the server conf # /usr/local/psa/admin/bin/httpdmng --reconfigure-all 2) I changed the apache conf files (if those were not taking full plesk top) vim /etc/apache2/ports.conf NameVirtualHost *:8008 Listen 8008 2.1) I do the same with /etc/apache2/sites-enables/000-default 3) I changed the port of my vhost (a single server) vim /var/www/vhosts/MYDOMAIN.COM/conf/XXXXXXXXX.http.include Replace the port 80 by this I want. Rebuild the vhost conf /usr/local/psa/admin/sbin/websrvmng --reconfigure-vhost --vhost-name=<domain_name> with without www (See my issue in serverfault: Edit vhost port in plesk 10.3 ) 4) I installed varnish by following this tutorial : http://www.euperia.com/linux/setting-up-varnish-with-apache-tutorial 5) I restart apache 2 + varnish service apache2 restart service varnish restart When I go to my site, I come across a page of apache It works! This is the default web page for this server. The web server software is running but no content has been added, yet. Can somebody help me ? This means that my vhost does not point to the right place. Why? What to do? How?

  Read the article

• My virtualhost not working for non-www version

  - by johnlai2004

  I have a development web server (ubuntu + apache) that can be accessed via the url glacialsummit.com. For some reason, http://www.glacialsummit.com serves pages from the /srv/www/glacialsummit.com/ directory, but http://glacialsummit.com serves pages from the /var/www/ directory. Here's what some of my virtualhost config files look like filename: /etc/apache2/sites-enabled/glacialsummit.com <VirtualHost 97.107.140.47:80> ServerAdmin [email protected] ServerName glacialsummit.com ServerAlias www.glacialsummit.com DocumentRoot /srv/www/glacialsummit.com/public_html/ ErrorLog /srv/www/glacialsummit.com/logs/error.log CustomLog /srv/www/glacialsummit.com/logs/access.log combined </VirtualHost> <VirtualHost 97.107.140.47:443> ServerAdmin [email protected] ServerName glacialsummit.com ServerAlias www.glacialsummit.com DocumentRoot /srv/www/glacialsummit.com/public_html/ ErrorLog /srv/www/glacialsummit.com/logs/error.log CustomLog /srv/www/glacialsummit.com/logs/access.log combined SSLEngine on SSLCertificateFile /etc/ssl/localcerts/www.glacialsummit.com.crt SSLCertificateKeyFile /etc/ssl/localcerts/www.glacialsummit.com.key <FilesMatch "\.(cgi|shtml|phtml|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory /usr/lib/cgi-bin> SSLOptions +StdEnvVars </Directory> BrowserMatch ".*MSIE.*" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 </VirtualHost> <VirtualHost 97.107.140.47:80> ServerAdmin [email protected] ServerName project.glacialsummit.com ServerAlias www.project.glacialsummit.com DocumentRoot /srv/www/project.glacialsummit.com/public_html/ ErrorLog /srv/www/project.glacialsummit.com/logs/error.log CustomLog /srv/www/project.glacialsummit.com/logs/access.log combined </VirtualHost> ## i have many other vhosts that work fine in this file filename /etc/apache2/sites-enabled/000-default <VirtualHost 97.107.140.47:80> ServerAdmin webmaster@localhost DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> filename: /etc/apache2/ports.conf NameVirtualHost 97.107.140.47:80 Listen 80 <IfModule mod_ssl.c> # SSL name based virtual hosts are not yet supported, therefore no # NameVirtualHost statement here Listen 443 </IfModule> How do I make http://glacialsummit.com serve web pages from /srv/www/glacialsummit.com/public_html just like http://www.glacialsummit.com?

  Read the article

• Win XP error 0x80041003 using GetObject/winmgmts

  - by John Lewis

  My computer is called "neil" and I want to set some values using WMI in vbScript. I adapetd the script below from one supplied by Microsoft. When I run it in my browser I get Error Type: (0x80041003) /dressage/30/pdf2.asp, line 8 I suspect it is some registry/security setting. Any advice? John Lewis FULL SCRIPT call Print_HTML_Page("http://neil/dressage/ascii.asp", "ascii") Sub SetPDFFile(strPDFFile) Const HKEY_LOCAL_MACHINE = &H80000002 strKeyPath = "SOFTWARE\Dane Prairie Systems\Win2PDF" strComputer = "." Set objReg=GetObject( _ "winmgmts:{impersonationLevel=impersonate}!\\" & _ strComputer & "\root\default:StdRegProv") strValueName = "PDFFileName" objReg.SetExpandedStringValue HKEY_LOCAL_MACHINE,_ strKeyPath,strValueName,strPDFFile End Sub Sub Print_HTML_Page(strPathToPage, strPDFFile) SetPDFFile( strPDFFile ) Set objIE = CreateObject("InternetExplorer.Application") 'From http://www.tek-tips.com/viewthread.cfm?qid=1092473&page=5 On Error Resume Next strPrintStatus = objIE.QueryStatusWB(6) If Err.Number 0 Then MsgBox "Cannot find a printer. Operation aborted." objIE.Quit Set objIE = Nothing Exit Sub End If With objIE .visible=0 .left=200 .top=200 .height=400 .width=400 .menubar=0 .toolbar=1 .statusBar=0 .navigate strPathToPage End With 'Wait until IE has finished loading Do while objIE.busy WScript.Sleep 100 Loop On Error Goto 0 objIE.ExecWB 6,2 'Wait until IE has finished printing WScript.Sleep 2000 objIE.Quit Set objIE = Nothing End Sub Update: Thanks for your reply. The line breaks seem to have been introduced in the process of paasting into this form. Well spotted - I was using a PDF file name "ascii". I added a .pdf extension but still get the error. I suspect you're right that it's to do with admin rights. Here's more about the setup and what I'm trying to achieve. Win2pdf is a product for writing PDFs by works by simulating a Windows printer. You "print" the page, select win2pdf in the print dialog and it then asks for a file name. I have it installed on my pc (called Neil) and it works fine in this conventional way. My aim is to write an html page to a PDF file using win2pdf - but via ASP/vbscript/javascript rather than with manual intervention. The script for doing this was provided by win2PDF's tech support but when it did not work, that was the limit of their understanding. In the sample script the file ascii.asp just produces a table of ascii codes/characters. The URL given is on my own PC which has IIS set up to run scripts which it does fine. The error I get occurs on about the fourth line executed. I am logged in with full admin rights - I think! But I'm no expert. I hope this helps to give some more specific suggestions about how to check/fix the admin rights.

  Read the article

• Is it reasonable that a random disk seek & read costs ~16ms?

  - by fzhang

  I am frustrated about the latency of random reading from a non-ssd disk. Based on results from following test program, it speeds ~16 ms for a random read of just 512 bytes without help of os cache. I tried changing 512 to larger values, such as 25k, and the latency did not increase as much. I guess it is because the disk seek dominates the time. I understand that random reading is inherently slow, but just want to be sure that ~16ms is reasonable, even for non-ssd disk. #include <sys/stat.h> #include <sys/time.h> #include <sys/types.h> #include <sys/unistd.h> #include <fcntl.h> #include <limits.h> #include <stdio.h> #include <string.h> int main(int argc, char** argv) { int fd = open(argv[1], O_RDONLY); if (fd < 0) { fprintf(stderr, "Failed open %s\n", argv[1]); return -1; } const size_t count = 512; const off_t offset = 25990611 / 2; char buffer[count] = { '\0' }; struct timeval start_time; gettimeofday(&start_time, NULL); off_t ret = lseek(fd, offset, SEEK_SET); if (ret != offset) { perror("lseek error"); close(fd); return -1; } ret = read(fd, buffer, count); if (ret != count) { fprintf(stderr, "Failed reading all: %ld\n", ret); close(fd); return -1; } struct timeval end_time; gettimeofday(&end_time, NULL); printf("tv_sec: %ld, tv_usec: %ld\n", end_time.tv_sec - start_time.tv_sec, end_time.tv_usec - start_time.tv_usec); close(fd); return 0; }

  Read the article

• How to create an EFI System Partition?

  - by Alex Popov

  TL; DR How do I create an EFI system partition from scratch? How do I put the EFI firmware on it onces it is created? Long version I hava Toshiba T430 laptop. I received it with Windows 7 installed (but I think originally it has shipped with Windows 8). I installed Ubuntu on it, but deleted some partitions on the disk so that I ended up wiping out the Windows and only having Ubuntu. Among the deleted partitions was the EFI System partition. I discovered that Ubuntu now boots in Legacy mode (and not UEFI). I am trying to follow this guide on converting my Ubuntu installation from Legacy to UEFI. The problem - since there is no EFI partition whenever I choose from BIOS to boot using UEFI I cannot boot. That counts not only for the harddrive, but usb and DVD as well. I think this is logical - it expects an EFI partition and since it can't find it, it cannot continue booting futher, be it from HDD or DVD. So how do I recreate the EFI partition? The guide above says: Creating an EFI partition If you are manually partitioning your disk in the Ubuntu installer, you need to make sure you have an EFI partition set up. If your disk already contains an EFI partition (eg if your computer had Windows8 preinstalled), it can be used for Ubuntu too. Do not format it. It is strongly recommended to have only 1 EFI partition per disk. An EFI partition can be created via a recent version of GParted (the Gparted version included in the 12.04 disk is OK), and must have the following attributes: Mount point: /boot/efi (remark: no need to set this mount point when using the manual partitioning, the Ubuntu installer will detect it automatically) Size: minimum 100Mib. 200MiB recommended. Type: FAT32 Other: needs a "boot" flag. I had some trouble creating this partition: I boot from a live Ubuntu DVD, open GParted, create a 200MB partition and format it to FAT32. In GParted I cannot set the mount point and thus cannot set the bootflag. I didn't set the mount point in /etc/fstab since it's a live CD and fstab looked quite differently from what I expected compared to a normal boot. Anyway, I just didn't know what values to set. I booted again via the live DVD and then chose to install Ubuntu. I then created a partition with the mentioned criteria - mount point, 200MB, FAT32, boot flag. However, I continue to have this problem and I suppose it's because on that partition there is no EFI firmware, it's just an empty partition, which is suitable to have EFI firmware. So again, how do I create an EFI partition, which has the EFI software, so that the laptop can once again boot in UEFI mode?

  Read the article

• getUserPrincipal() in JCIFS / Lan-Manager authentitation level setting in Windows 2k8

  - by Chris

  I have to find out in which exact format JCIFS stores the user principal in the "getUserPrincipal()" property. Therefor i created a test Environment like this: Windows Server 2008 Domain Controller Domain named "MYDOMAIN" Many Testusers in Active Directory Tomcat Application Server with my Web Application (which simply reads the user Principal and displays its values). The user should be logged in to the web-application with SSO therefor i need the format that jcifs is using to store the user. (For example user@MYDOMAIN or MYDOMAIN\user...) I tested the Authentication with other SSO frameworks with Kerberos Method and it works as expected. I'm now trying to use SSO through the NTLMHttpFilter of JCIFS. When i try to login i get the following error message: jcifs.smb.SmbException: The parameter is incorrect. jcifs.smb.SmbTransport.checkStatus(SmbTransport.java:541) jcifs.smb.SmbTransport.send(SmbTransport.java:641) jcifs.smb.SmbSession.sessionSetup(SmbSession.java:322) jcifs.smb.SmbSession.send(SmbSession.java:224) jcifs.smb.SmbTree.treeConnect(SmbTree.java:176) jcifs.smb.SmbSession.logon(SmbSession.java:153) jcifs.smb.SmbSession.logon(SmbSession.java:146) jcifs.http.NtlmHttpFilter.negotiate(NtlmHttpFilter.java:189) jcifs.http.NtlmHttpFilter.doFilter(NtlmHttpFilter.java:121) Regarding to the documentation i'm using to configure this, this is a know issue with the Group policy. It is stated there, that i have to change the Group policy "Networkaccess: lan-manager authentication level" to respond to NTLMv1 request. I have done this, but it's still not working. So what i also have to configure is the same policy on the client computer. I have to change the policy, so that the client computer sends NTLMv1. But it is always sending NTLMv2 tokens. The problem now is that i'm somehow not able to change this setting. (I already was before) because the dropdown box to choose the authentication method is "greyed out". edit: just to make this clear, this dialog is on the client-side in the "local-security policies" As you can see from this screenshot, the chosen method is "Only send NTLMv2 responses" which is the wrong setting and i'm pretty sure that this is causing the error above. My question is now, why can't i change this setting? Why is it greyd out?

  Read the article

• Apache2 & .htaccess : Apache ignoring AccessFile

  - by Elyx0

  Hi there here is my server configuration: DEBIAN 32Bits / PHP 5 / Apache Server version: Apache/2.2.3 - Server built: Mar 22 2008 09:29:10 The AccessFiles : grep -ni AccessFileName * apache2.conf:134:AccessFileName .htaccess apache2.conf:667:AccessFileName .httpdoverride All the AllowOverride statements in my apache2/ folder. mods-available/userdir.conf:6: AllowOverride Indexes AuthConfig Limit mods-available/userdir.conf:16: AllowOverride FileInfo AuthConfig Limit mods-enabled/userdir.conf:6: AllowOverride Indexes AuthConfig Limit mods-enabled/userdir.conf:16: AllowOverride FileInfo AuthConfig Limit sites-enabled/default:8: AllowOverride All sites-enabled/default:14: AllowOverride All sites-enabled/default:19: AllowOverride All sites-enabled/default:24: AllowOverride All sites-enabled/default:42: AllowOverride All The sites-enabled/default file : 1 <VirtualHost *> 2 ServerAdmin [email protected] 3 ServerName mysite.com 4 ServerAlias mysite.com 5 DocumentRoot /var/www/mysite.com/ 6 <Directory /> 7 Options FollowSymLinks 8 AllowOverride All 9 Order Deny,Allow 10 Deny from all 11 </Directory> 12 <Directory /var/www/mysite.com/> 13 Options Indexes FollowSymLinks MultiViews 14 AllowOverride All 15 Order allow,deny 16 allow from all 17 </Directory> 18 <Directory /var/www/mysite.com/test/> 19 AllowOverride All 20 </Directory> 21 22 ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ 23 <Directory "/usr/lib/cgi-bin"> 24 AllowOverride All 25 Options ExecCGI -MultiViews +SymLinksIfOwnerMatch 26 Order allow,deny 27 Allow from all 28 </Directory> 29 30 ErrorLog /var/log/apache2/error.log 31 32 # Possible values include: debug, info, notice, warn, error, crit, 33 # alert, emerg. 34 LogLevel warn 35 36 CustomLog /var/log/apache2/access.log combined 37 ServerSignature Off 38 39 Alias /doc/ "/usr/share/doc/" 40 <Directory "/usr/share/doc/"> 41 Options Indexes MultiViews FollowSymLinks 42 AllowOverride All 43 Order deny,allow 44 Deny from all 45 Allow from 127.0.0.0/255.0.0.0 ::1/128 46 </Directory> 47 48 49 50 51 52 53 54 </VirtualHost> If i change any Allow from all in Deny from all , it works whenever i put it. I've got one .htaccess at /mysite.com/.htaccess & one at /mysite.com/test/.htaccess with: Order Deny,Allow Deny from all Neither of them work i can still see my website. I've got mod_rewrite enabled but i don't think it does anything here. I've tried almost everything :/ It works on my local environnement (MAMP) but fails when on my Debian server.

  Read the article

• Why MySQL sat for 2 minutes doing nothing?

  - by Alex R

  This was a one-time thing, not reproducible... But I saved the show innodb status output. Can anybody tell what's going on here? The simple insert took almost 3 minutes to complete. | InnoDB | | ===================================== 110201 15:58:10 INNODB MONITOR OUTPUT ===================================== Per second averages calculated from the last 34 seconds ---------- SEMAPHORES ---------- OS WAIT ARRAY INFO: reservation count 11963, signal count 11766 --Thread 1824 has waited at .\btr\btr0cur.c line 443 for 118.00 seconds the sema phore: S-lock on RW-latch at 09D6453C created in file .\buf\buf0buf.c line 550 a writer (thread id 1824) has reserved it in mode wait exclusive number of readers 1, waiters flag 1 Last time read locked in file .\buf\buf0flu.c line 599 Last time write locked in file .\btr\btr0cur.c line 443 Mutex spin waits 0, rounds 527817, OS waits 7133 RW-shared spins 2532, OS waits 1226; RW-excl spins 1652, OS waits 1118 ------------ TRANSACTIONS ------------ Trx id counter 0 95830 Purge done for trx's n:o < 0 95814 undo n:o < 0 0 History list length 11 LIST OF TRANSACTIONS FOR EACH SESSION: ---TRANSACTION 0 0, not started, OS thread id 3704 MySQL thread id 551, query id 2702112 localhost 127.0.0.1 root show innodb status ---TRANSACTION 0 95829, not started, OS thread id 3132 MySQL thread id 534, query id 2702020 localhost 127.0.0.1 root ---TRANSACTION 0 95828, not started, OS thread id 3152 MySQL thread id 527, query id 2701973 localhost 127.0.0.1 root ---TRANSACTION 0 95827, ACTIVE 118 sec, OS thread id 1824 inserting, thread decl ared inside InnoDB 500 mysql tables in use 1, locked 1 1 lock struct(s), heap size 320, 0 row lock(s) MySQL thread id 526, query id 2701972 localhost 127.0.0.1 root update INSERT INTO log_searchcriteria (userid,search_criteria,date,search_type) VALUES ( NAME_CONST('userid',NULL), NAME_CONST('search_criteria',_latin1' SELECT SQL_C ALC_FOUND_ROWS idx_search.CTCX_LATITUDE, idx_search.CTCX_LONGITUDE, idx_search.b uilding_id, idx_search.LN_LIST_NUMBER, idx_search.LP_LIST_PRICE, idx_search.HSN_ ADRESS_HOUSE_NUMBER, idx_search.STR_ADDRESS_STREET, idx_search.CP_ADDRESS_COMPAS S_POINT, idx_search.UN_UNIT, idx_search.CIT_CITY, idx_search.ZP_ZIP_CODE, idx_se arch.AR_AREA_NAME, idx_search.BR_BEDROOMS, idx_search.BTH_BATHS, idx_search.ST_S TATUS, idx_search.CTCX_STYLE_TYPE, idx_s -------- FILE I/O -------- I/O thread 0 state: wait Windows aio (insert buffer thread) I/O thread 1 state: wait Windows aio (log thread) I/O thread 2 state: wait Windows aio (read thread) I/O thread 3 state: wait Windows aio (write thread) Pending normal aio reads: 0, aio writes: 1, ibuf aio reads: 0, log i/o's: 0, sync i/o's: 0 Pending flushes (fsync) log: 0; buffer pool: 0 151006 OS file reads, 120758 OS file writes, 6844 OS fsyncs 0.00 reads/s, 0 avg bytes/read, 0.00 writes/s, 0.00 fsyncs/s ------------------------------------- INSERT BUFFER AND ADAPTIVE HASH INDEX ------------------------------------- Ibuf: size 1, free list len 5, seg size 7, 24664 inserts, 24664 merged recs, 4612 merges Hash table size 553253, node heap has 629 buffer(s) 0.00 hash searches/s, 0.00 non-hash searches/s --- LOG --- Log sequence number 5 2318193115 Log flushed up to 5 2318193115 Last checkpoint at 5 2318129891 0 pending log writes, 0 pending chkp writes 3036 log i/o's done, 0.00 log i/o's/second ---------------------- BUFFER POOL AND MEMORY ---------------------- Total memory allocated 213459462; in additional pool allocated 1720192 Dictionary memory allocated 240416 Buffer pool size 8192 Free buffers 0 Database pages 7563 Modified db pages 18 Pending reads 0 Pending writes: LRU 0, flush list 18, single page 0 Pages read 150973, created 28788, written 115137 0.00 reads/s, 0.00 creates/s, 0.00 writes/s No buffer pool page gets since the last printout -------------- ROW OPERATIONS -------------- 1 queries inside InnoDB, 0 queries in queue 1 read views open inside InnoDB Main thread id 2992, state: flushing buffer pool pages Number of rows inserted 794294, updated 89203, deleted 13698, read 1453084305 0.00 inserts/s, 0.00 updates/s, 0.00 deletes/s, 0.00 reads/s ---------------------------- END OF INNODB MONITOR OUTPUT ============================ Thanks

  Read the article

• Can't connect to shared folders anymore?

  - by HuskyHuskie

  My home server is running Windows Server 2008 R2. I've had it running for almost a year now without any issues with shared folders. This past week I had an issue with my modem which required it to be power cycled and with that I power cycled my router. After that I haven't been able to connect to my shared network folders. I have no idea why that would even cause an issue as I've power cycled my networking equipment in the past without issues and none of my settings appear to have been lost. I am mapping these drives on my Windows 7 Ultimate machine using "Map Network Drive", from there I enter \\SERVER\Storage as I'm trying to connect to my shared folder named Storage. I receive the following error every time I try mapping the drive: Windows cannot access \\Server\Storage Check the spelling of the name. Otherwise there might be a problem with your network. To try to identify and resolve network problems, click Diagnose. Details: Error code: 0x80070035 The network path was not found. When I click Diagnose I get the following: Problems found file and print sharing resource (SERVER) is online but isn't responding to connection attempts. The remote computer isn't responding to connection on port 445, possibly due to firewall or security policy settings, or because it might be temporarily unavailable. Windows couldn't find any problems with the firewall on your computer. I've tried this from multiple computers with the same issue too. To resolve the problems so far I've tried: Disabling the firewall on SERVER Reinstalling File Services Modifying NetBT\Parameters registry values Adding a custom inbound rule for port 445 Adding port forwarding on my router for port 445 Recreating the shared folders Checking and rechecking the shared folder permissions. Resetting my user account password on the server used to access the shared folder. I'm pulling my hair out with this problem mainly because it came out of nowhere. It was working fine the night before and the next day it just stopped working. Any ideas of what I could try next are much appreciated. It should also be noted that this server is used as a web server too and that functionality still works correctly.

  Read the article

< Previous Page | 774 775 776 777 778 779 780 781 782 783 784 785  | Next Page >