Search Results

Search found 28350 results on 1134 pages for 'command switch'.

Page 78/1134 | < Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85  | Next Page >

• Tomato/DD-WRT router to act as switch & only NAT some port

  - by fseto

  BACKGROUND: I have a device that must use a real IP address. Currently, my ISP uses DHCP and I can have up to 4 real IP address assigned. However, the cable modem only have 1 ethernet port and it's connected to my router (running Tomato, but can run DD-wrt or other Openwrt if required). Question stems from how I can connect the additional device, requiring a real IP? EASY SOLUTION: would be to get a switch and connect to the CM, Router, and Device. But alas, I want to avoid this route, since: my wiring cabinet in my home is drawing lots of power and heat already Device will be unprotected by any firewall unable to monitor the traffic to/from device. Besides, what would be the FUN in that? =) IDEA: So what I want to do is to configure the router, so that one of the switchport is removed from the normal br0 bridge. Instead, I want to make it behave like a switch on the WAN port. What's the best way of doing this? Should I create another bridge on the WAN & the device port? Can a single port belongs to two bridges? or would I need to create a subinterface first? Would I need a DHCP-relay? Am I expecting too much from my poor cheapie router? +------+ | CM | +--++--+ || +----WAN---------------+ | / \ Router | | BR1? BR0 | | | \ | | | {NAT} | | | / | | \ | +-P0----P1-P2-P3-Wifi--+ | +------+ |Device| +------+

  Read the article

• ProCurve ACL to prevent a subnet from leaving the switch

  - by kce

  I have a single HP ProCurve 2610 in a remote location that is connected in with the rest of the network via SHDSL. There are two Layer-3 networks on this segment. ACLs are setup to deny one subnet (192.0.2.0/24) from ever being able to leave the switch by virtue of being applied to port attached to the upstream connection. The other subnet should be permitted to freely leave the switch. Both subnets are on the same VLAN. Unfortunately SFlow very clearly show broadcast traffic from 192.0.2.0/24 on the upstream connection. ProCurve ACLs are not my strong suit but I feel like I'm missing something very simple here. ip access-list extended "Filter for Camera Network" deny ip 192.0.2.0 0.0.0.255 0.0.0.0 255.255.255.255 log permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 exit interface 24 name "DSL - UPLINK" access-group "Filter for Camera Network" in exit Unless I am mistaken traffic from 192.0.2.0/24 should be dropped as it crosses the uplink port (int 24) whereas all other traffic will be permited by the following default allow rule. What exactly am I missing here? EDIT: Firstly, why do you have two subnets contained in the same VLAN? Because that's how it was configured by a previous administrator and while it makes conceptual sense that a single subnet is "mapped" to a single VLAN there's no technical constraint that I am aware of that makes this have to be the case. Instead of filtering inbound traffic on your uplink, you should be filtering outbound traffic. The HP2600 series can only filter inbound traffic on interfaces. Should I change my filter to deny any to 192.0.2.0/24?

  Read the article

• Configure linux machine as bridge/switch and end device

  - by leemes

  At my home, I have two desktop PCs in two rooms. The router / DSL modem is in one of these rooms. Now I want to configure a home server (having 2 LAN ports, running 24/7) in the corridor between the two rooms, using only one LAN cable at each door. This gives me the following physical configuration: (door) (door) .----/-/----. .-----/-/----------._ FritzBox | | | .----´´ DSL Router PC1 Server | PC2 As just said, the server has 2 network interfaces and is running Ubuntu. What I need now is a network configuration which enables both the server and PC1 to connect to the router. I think the server needs to serve as a bridge or switch. Currently, all computers are configured having static IP addresses. If I'm understanding it correctly, a bridge / switch doesn't have its own IP address, but as the server needs to be configured as an own end device, it needs to have one. My first question is, do I have to configure both interfaces separately, giving both the same static IP address? My next question is, how do I bridge the two physical networks into one? I have basic understanding (but am always confused again and again) of bridges and switches, but I don't know how to configure it in software. I only know that it's possible to do so :) The third question is: Is it possible to configure this in a way that network packets from/to PC1 to/from the router only go through hardware or only consume low CPU in the server? Can you help me? Thanks in advance!

  Read the article

• Conditionally create symbolic link by filesize using find exec ubuntu 10.04

  - by jmlw

  I have an interesting problem. I'm trying to create symbolic links in a single folder, for all files in a directory which are larger than a specified size. For clarification, here is an example: /Files /Large_Files /LargeFile1_symlink /LargeFile2_symlink /Folder1 /file_a /file_b /Folder2 /LargeFile1 /Folder3 /LargeFile2 /file_c What I have so far to try to accomplish this is: find -size +102400 -exec ln -s $PWD/{} Large_Files/ \; However, this find produces ./LargeFile1 So my symlink command produces ln -s /Files/Folder2/./LargeFile1 Large_Files/ My question is, would it be possible to use the basename command to separate out only the filename so this command will work? Or does anybody have a suggestion on how to do this without writing a script, or give me an example on writing a script? I've never done scripting before, but I do know Java, but don't want to take the time to do all this in Java. Thank you for any help! Edit: adding tags

  Read the article

• Scripting a Windows 2008 Cluster from Windows 2003

  - by glancep

  Our current environment is all Windows 2003. When we migrate a new version of our service to the cluster, we first stop the service with a command like: cluster.exe <clusterName> resource "<serviceName>" /offline We do similarly after the migrate to bring the service back online. Now, we are upgrading our environment to new Windows 2008 servers. However, our build/migrate machine will remain Windows 2003. When issuing the same command from Windwos 2003 to Windows 2008, we get: System error 1722 has occurred (0x000006ba). The RPC server is unavailable. We need to be able to remotely administer a Windows 2008 cluster from a Windows 2003 server in an automated fashion (such as the command-line cluster.exe utility). Is this possible? Thanks, Gideon

  Read the article

• Displaying what `history` line is current in bash prompt

  - by warren

  What formatting character needs to be added to a bash prompt to indicate the most recent history item run (or the current command number if 1 could be added to the last history entry)? My prompt string is this: \[\033[33m\][\u@\[\033[1;31m\]\h]\]\033[0m {\W}\n\033[1;34m\]\w\]\033[0m > Gives me the following display: [user@host] {~} ~ > User is in yellow, and the host is in red. The entry in brackets is the current directory, and the entry before the greater-than sign is the full pwd. Can I append to the first line the current command number so I would have something like the following: [user@host] {~} (nnn) ~ > where (nnn) is the current (or just processed) command number, as shown when running history?

  Read the article

• Bash preexecute

  - by Alex_Bender

  I'm trying to write bash command wrapper, which will be patch bash current command on the fly. But i'm faced with the problem. As i'm not a good Shell user, i can't write right expression of variable assignment in string. See bellow: I'm set trap to preexecute, through this: alex@bender:~$ trap "caller >/dev/null || xxx \"\${BASH_COMMAND}"\" DEBUG; I want change variable BASH_COMMAND, do something like BASH_COMMAND=xxx ${BASH_COMMAND} but i don't know, how i need escaping variables in this string NOTE: xxx -- my custom function, which must return some value, if in end of command situated word teststr function xxx(){ # find by grep, if teststr in the end `echo "$1" | grep "teststr$" >/dev/null`; # if true ==> do if [ "$?" == "0" ]; then # cut last 6 chars (len('teststr')==6) var=`echo "$1" | sed 's/......$//'`; echo "$var"; fi } How can i do this stuff?: alex@bender:~$ trap "caller >/dev/null || ${BASH_COMMAND}=`xxx $BASH_COMMAND`" DEBUG;

  Read the article

• Mac OS X bash prompt bug?

  - by Memo

  I am trying to set my bash prompt to display the time and current directory in bold: export PS1="\[\e[1m\][\A] \w \$ \[\e[0m\]" This does apparently work, but when I use the command history (ctrl-r), after finding the command I was searching for and pressing enter, this line is not displayed correctly. Here is an example: [21:58] ~/Wyona/svn-repos/zwischengas $ (reverse-i-search)`ta': tail -F logs/log4j-cnode1.log becomes, after pressing enter: [21:58] ~/Wyona/svn-repos/zwischengas $ -F logs/log4j-cnode1.log Of course, this is not "really" a problem, since the command does work correctly, but it is still annoying. Does anybody know why this happens? And, more importantly, how to prevent/fix it? Thanks, Memo

  Read the article

• Mapped commands in VIM starting with a Comma

  - by Boldewyn

  In my .vimrc, I defined this line: map ,ps <Esc>:!ps<Space>-a<CR> The mapping is set (which I controlled via :verbose map ,ps while inside vim). There is nothing else mapped to the comma. However, if I type the command in command mode, nothing is displayed in the status bar, the comma is ignored, the p movement and the s insert are triggered. (I.e., VIM reacts, as if there was no command ,ps.) Is there any magic that I have overlooked in enabling comma-started mapped commands?

  Read the article

• How do you configure ConEmu to run cmd.exe as an Administrator from an Explorer integration?

  - by bentayloruk

  I am trying to add a ConEmu Here - Explorer context menu integration entry for the Visual Studio 2012 command prompt. I want the shortcut to Run as Administrator. I am not sure of the right way to do this in ConEmu. I am using the following Command (which works but obviously not as Admin): cmd.exe /k ""C:\Program Files (x86)\Microsoft Visual Studio 11.0\VC\vcvarsall.bat"" x86 What is the correct way to configure ConEmu to run this as Administrator? If there is not a correct way, how should I adjust the command to make this work?

  Read the article

• Create an alias in Windows XP

  - by Lord Torgamus

  Back in school, I used to have a .login file along the lines of alias ll = ls -l alias dir = ls -Fhl alias web = cd ~/public/public_www/development ... I'd like to do that sort of thing with my XP box here at work, but most of the resources I've found online seem fairly complicated and heavy-duty. Is there a way to do this that doesn't involve mucking about in the registry or running a large batch file? EDIT: My original reason for asking this was that I only need the command line for one command in one specific folder, and I wanted to be able to get to that folder quickly when I launched the command line. But the accepted answer for this question is so good that I decided to ask about my original issue as a separate question here.

  Read the article

• How to install and Configure MTA on Linux [closed]

  - by Umair Mustafa

  I need to know which MTA's is better and simple to handle and configure in linux. As I need to run a script that will send me the output of that command whenever it will run using cron. Ok the case is this. Every day I have to manually check the Disk space of server which are more than 30 which is headache and have to document that. So I will simply add the follwing command DF- H and the output of this command should be send on my email. So now IF u got the story then tell me what MTA is better sendmail, postfix and some instructions on HOW TO INSTALL and CONFIGURE it. And after configuring the How do I add the DF -H so that it will start seniding me the output on my email. Thanks in advance.

  Read the article

• organizing images by resolution with batch files

  - by Anthony

  Doing some digging I'm trying to figure out a command line solution for organizing very large archives of images based on their resolution into folders, 1920x1080, 1600x1200, 1600x900, etc. I've come across a few post on Superuser mentioning something called ImageMagick, is that the best method to the madness I'm trying to accomplish? I've never used any command line functions/applets/tools other then those that come from Microsoft. I'm rather new to command line usage but ive been enjoying the hell out of it using Powershell, xcopy and robocopy. I am slowly trying to push myself further into the Linux world with Ubuntu running on one of my physical machines as well as a virtual machine so that's an option as well.

  Read the article

• How to lock the c prompt?

  - by allindal

  Is there anyway to lock the command prompt? I need my computer to require a password to use the command prompt. I lock the workstation occasionally but sometimes I forget and if I could just prevent my roommate from doing the "c: net user user *" to change my password it would be great. I do not want to have to use the rundll.32 user command with script to automatically lock the computer. Just a way to lock the c prompt. Sorry for not saying this earlier, I'm running a vista 32bit Asus gene II motherboard with a core i7 CPU

  Read the article

• PHP Apache XAMPP Run Multiple Scripts from CLI in Background

  - by Pamela

  How can I simultaneously run dozens of PHP scripts in the background from XAMPP's command line interface? Someone suggested a batch file, but when I tried executing this: start php 1.php start php 2.php start php 3.php It only opened a command prompt window; I closed that window, then two more command prompt windows opened up executing 2.php and 3.php. I want to run as many scripts as I want all simultaneously and all in the background. What is the best way to accomplish this, and how can it be done?

  Read the article

• Executing EXE with wildcard from psexec

  - by Danny

  I'm writing a few scripts that I am using to integrate with bamboo for some continuous integration improvements and I've run into a bit of a snag. I'm currently trying to run a psexec command that installs the latest build on the remote machine but I dont necessary know the revision number. For example, the remote exe file could be Installer-3.1.xxxxx.exe where the xxxxx changes. I tried running the command with Installer-3.1.*.exe but it takes it as literal in Windows. I'm not overly familiar with Windows command prompt and am more used to Linux at this moment.

  Read the article

• powershell run java process problem

  - by Limited Atonement

  Dear Sirs, I'm trying to run a java process via Powershell in Windows XP. Here's the command: java.exe -cp .;./common.jar -Dcontext=atest1 -Dresourcepath=. DW_Install So, the classpath is . and .\common.jar (I think java takes the wrong slashes, right?) There are two environment variables, one "atest1" the other "." and the class to execute main on is DW_Install (in the default package). This command works in cmd.exe, but doesn't is PS. What's going on? What is PS doing while parsing this command that CMD doesn't do (or vice versa)? Aaron

  Read the article

• Replace special text with sed?

  - by user143822

  I'm using CMD on Windows Xp to replace special text with Sed. I'm using this command for replace special characters like $ or * : sed -i "s/\*/123/g;" 1.txt But how command must i use to replace this strings with ciao! in my text files? Is possible? \\ \\\ "" sed.exe -i "s/{\*)(//123/ sed -i "s/\\/123/g;" 1.txt the previous command does not work because i have \, " and other special strings that sed use to make regex.

  Read the article

• cd (change directory) to my home directory on Windows [closed]

  - by deostroll

  Possible Duplicate: Is there a short cut command in Windows command prompt to get to the current users home directory like there is in Linux? Any short way to cd to the user specific directories in the command prompt. Like for e.g. in linux shell (debian based) we do a cd ~ and it instantly takes to the current logged user's directory /home/<username>. Anything to this effect on windows? ps: currently trying to do this on xp machines. If it differs for other machines, mention that too.

  Read the article

• Is there a way to catch cmd.exe windows into tabs?

  - by user55542

  I use an editor that allows me to type in a command to run. In order to see the output without having to redirect it to a file, I precede the command with "cmd /k," which leaves an open cmd.exe window. So I'd like to find a way to move catch the call to cmd.exe and give it to an application that tabifies cmd.exe, a terminal emulator as it's called. The desired result would be similar to what happens in a tabbed editor, when that editor is to open some file, it does so in another tab, and not in another window. While in a given situation it may be easier to modify the command to redirect output to display in the editor itself, in general it would be more helpful if I could find a way to catch all such calls into one window.

  Read the article

• Is there a BSD equivalent to "!!"?

  - by CT

  I often find myself issuing a command that I do not have the proper elevated privileges for. On Ubuntu I could use sudo !! This would issue the same command with sudo privlidges. Is there an equivalent on OpenBSD? Edit: I should have been more specific on what version of OpenBSD. I am using OpenBSD 4.8 where sudo seems to be installed by default. I have already created a user besides root and edited my sudoers file to allow for that user to use sudo. My question is, is there already a built-in shortcut for the "!!" to use previous command.

  Read the article

• Directories will list, but are not recognize by cd

  - by mdimond

  New to terminal and having problems out of the gate. Using Terminal 2.1.2 on a Mac running 10.6.8. Using the "ls Documents" will list the contents, but when I try to change directories, which I tried several different ways, I get the following results: new-host-2:~ MDimond$ cd. -bash: cd.: command not found new-host-2:~ MDimond$ cd./Users/MDimond/Documents -bash: cd./Users/MDimond/Documents: No such file or directory new-host-2:~ MDimond$ cd. /Documents -bash: cd.: command not found The /usr/bin has the cd command listed; the /bin does not. Any assistance would be greatly appreciated. Thanks, md

  Read the article

• Why does FIND on Windows 7 give an "Access Denied" error?

  - by rann

  Hi All, I have an administrator account on a Windows 7 x64 machine. It is not THE administrator account, the account is simply a member of the administrators group. The install is default. When the user opens a command prompt it ends up in the users' %HOMEPATH% directory where you'll find various directories like the Documents folder. If the user uses the following (windows) FIND command, an "Access Denied" error occurs: FIND /I "My String" C:\Users\Rann\Documents Access denied - C:\USERS\RANN\DOCUMENTS Using runas or right-clicking on the command prompt to run it as an administrator does not change this behaviour; an administrator-level cmd.exe still gives me the same error. Changing the path to any other directory gives the same error. My question is thus: How is one supposed to use the FIND (and possibly other) commands? What rights are needed?

  Read the article

• JQuery quiz app - use <id> tag to toggle variable on/off

  - by hairyllama

  Hi, I am writing a jquery phonegap quiz app and have a number of categories from which a user can select via checkbox. Relevant questions belonging to those categories are then returned. However, I have two huge switch statements to change the relevant variables from 0 to 1 if the checkbox for that category is selected and vice versa (this info is used to build a compound db query). The value of the variable behind the checkbox is only ever 0 or 1, so is there a better way to do this? My HTML is: <h2>Categories</h2> <ul class="rounded"> <li>Cardiology<span class="toggle"><input type="checkbox" id="cardiology" /></span></li> <li>Respiratory<span class="toggle"><input type="checkbox" id="respiratory" /></span></li> <li>Gastrointestinal<span class="toggle"><input type="checkbox" id="gastrointestinal" /></span></li> <li>Neurology<span class="toggle"><input type="checkbox" id="neurology" /></span></li> </ul> My Javascript is along the lines of: var toggle_cardiology = 0; var toggle_respiratory = 0; var toggle_gastrointestinal = 0; var toggle_neurology = 0; $(function() { $('input[type="checkbox"]').bind('click',function() { if($(this).is(':checked')) { switch (this.id) { case "cardiology": toggle_cardiology = 1; break; case "respiratory": toggle_respiratory = 1; break; case "gastrointestinal": toggle_gastrointestinal = 1; break; case "neurology": toggle_neurology = 1; break; etc. (which is cumbersome with 10+ categories plus an else statement with a switch to change them back) I'm thinking of something along the lines of concatenating the HTML id tag onto the "toggle_" prefix - in pseudocode: if (toggle_ + this.id == 1){ toggle_ + this.id == 0} if (toggle_ + this.id == 0){ toggle_ + this.id == 1} Thanks, Nick.

  Read the article

• Running a command that produces no output with SharpSSH

  - by Paolo Tedesco

  I want to run a command using ssh. I am using the SharpSSH library, as in this example: using System; using Tamir.SharpSsh; class Program { static void Main(string[] args) { string hostName = "host.foo.com"; string userName = "user"; string privateKeyFile = @"C:\privatekey.private"; string privateKeyPassword = "xxx"; SshExec sshExec = new SshExec(hostName, userName); sshExec.AddIdentityFile(privateKeyFile, privateKeyPassword); sshExec.Connect(); string command = string.Join(" ", args); Console.WriteLine("command = {0}", command); string output = sshExec.RunCommand(command); int code = sshExec.ChannelExec.getExitStatus(); sshExec.Close(); Console.WriteLine("code = {0}", code); Console.WriteLine("output = {0}", output); } } My problem is that when the command I run produces no output, I get -1 as return code, instead of the code returned by the command on the remote machine. Has someone encountered this problem, or am I doing something wrong?

  Read the article

< Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85  | Next Page >