Search Results

Search found 21644 results on 866 pages for 'connection speed'.

Page 78/866 | < Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85  | Next Page >

  • Hibernate speed, and hard drive temperature

    - by cometbill
    My computer is taking in the region of 4 minutes or so, to hibernate 4GB of RAM. Also, resting my hand on the top of it is rather hot to the touch, so I ran CrystalDisk Info and that is reporting a temperature of 49 degrees C. I It's a Western Digital 5400 rpm drive, I've had it in the laptop since I bought it for most of the 2.75 years I've had it. Power on Count is 1219 Power on Hours is 3940 hours Boot up time is quicker than resuming from hibernate, too. Is there anything I can / should check ? Advice is greatly appreciated.

    Read the article

  • Losing internet connection after few minutes (5-10 maybe)

    - by Korchkidu
    I took a computer that was not updated for months. Internet was working just fine so basically, I updated zonealarm, avast and installed all windows updates and especially SP3. After that, when I reboot, Internet works fine but after few minutes, Firefox says that the connection was reset. IE does not work either. However, my connection is still up and running as I can make a ping on www.google.com for example. Here are the solutions I tried with no success so far: 1) Uninstalling SP3; 2) Uninstalling IE8 and IE7; 3) Manually setting DNS and IPs; 4) Removed proxy settings from Firefox and IE; 5) Restarting DNS and DHCP related services; 6) Reset TCP/IP with netsh int ip reset c:\resetlog.txt; 7) Updated my ehternet card driver; 8) Restarted, tweaked all the connections in any directions and any configuration possible I believe; 9) Disabled Zone Alarm and Avast; Also, update kb981793 always fails on install. Please, help me as I spent two days already on this and I cannot find any solution. If I cannot fix this problem tomorrow, I will have to format-reinstall everything. Thanks for any help. Regards.

    Read the article

  • Connection failed between Windows Servers

    - by Kerby82
    I'm setting up an infrastructure based on Windows Server 2012. The firewall is turned off and I can't access the Domain controller to check for the group policy. I'm experiencing some connection problem between servers. All the servers are running a site on the TCP Port 80 and I check with netstat that the web server is binding on every Ip of the servers. If i try to telnet from the server itself on the port 80 it works (using DNS name) if I try same telnet from another machine I get connection failed. The DNS works, the ping is successfull, the servers are on the same subnet, the firewall is turned off (even though windows advanced firewall says that some settings can be managed by the System Administrator, i guess group policy). I don't know how to troubleshoot further. Do you have any idea? Is that possible that the FW looks turned off but there are some group policy blocking the connections? (I also check group policy-Administrative Template-Network Connections- Windows FW everything is not configured) I need some hint on how to keep troubleshooting such a problem.

    Read the article

  • Where would an S3 upload speed cap originate?

    - by CoreyH
    I do a ton of uploading to S3 and am experiencing capped speeds and I can't quite figure out how to address it. The setup: Windows Server 2008 R2 x64, external HD, using a Java based upload tool called Jsh3ll and custom VBS scripts to kick the jobs off. Running one process at a time, I am always limited to about 4mbps. I have FiOS at 35/35mbps speeds, so it isn't an outright limit. AND, I can run parallel instances and can go all the way up to 35mbps, so I know the problem isn't gateway/nic/machine/amazon related. Running parallel instances works to a degree as a solution, but increases the complexity of my workflow greatly. Solving this would make my life dramatically easier. When I was first doing this I was playing around with a bunch of Windows TCP parameters and was able to briefly get unconstrained bandwidth, but it wasn't repeatable. Thoughts?

    Read the article

  • DNS Resolver Speed Techniques

    - by Rob Olmos
    I recently received a reply to my concerns about some DNS servers being slower than others despite all servers being anycast: In practice, most resolvers won't be impacted by the slower paths to some of the name servers in the set. Most resolvers employ various techniques to provide fast lookups, such as preferring name servers that were previously seen to be faster, sending simultaneous queries to multiple name servers, or pre-fetching queries before the TTL has expired. I was not aware that resolvers used these techniques and I was unsuccessful at searching for more info about this. Are there any names for these techniques? Which resolvers employ which of these techniques?

    Read the article

  • Ubuntu: Network connection seems to fail after some time

    - by chrischu
    I just bought a Shuttle XS-35 barebone mini-PC and put a 1 TB WD hard drive and 2 Gigs of RAM into it and installed Ubuntu onto it. The machine will post as a media server (streaming videos to my PS3) and as a webserver for some small private projects. Now I wanted to copy my videos from my Windows 7 machine to the Ubuntu machine and therefore created a Samba share on the Ubuntu machine. I tried copying the files with the standard Windows copy function and with SyncToy but after some time (sometimes 5 copied files, sometimes 120 copied files) the Samba share just disappears. When that happens I can't reach the internet from the Ubuntu machine although the network connection still seems to be fine (IP still there etc.). Between the machines lies a LinkSys router. When I try to ping my router (after the connection doesn't work anymore) from the Ubuntu machine only a very small subset of the packages actually get there (something around 20%). When I restart the Ubuntu machine everything seems to work normal again. I have no idea where the problem lies here. Does anybody have a clue? Thanks in advance!

    Read the article

  • The best way to hide data Encryption,Connection,Hardware

    - by Tico Raaphorst
    So to say, if i have a VPS which i own now, and i wanted to make the most secure and stable system that i can make. How would i do that? Just to try: I installed debian 7 with LVM Encryption via installation: You get the 2 partitions a /boot and a encrypted partition. When booting you will be prompted to fill in the password to unlock the encryption of the encrypted partition, Which then will have more partitions like /home /usr and swapspace which will automatically mount. Now, i do need to fill in the password over a VNC-SSL connection via the control panel website of the VPS hoster, so they can see my disk encryption password if they wanted to, they have the option if they wanted to look at what i have as data right? Data encryption on VPS , Is it possible to have a 100% secure virtual private server? So lets say i have my server and it is sitting well locked next to me, with the following examples covered bios (you have to replace bios) raid (you have to unlock raid-config) disk (you have to unlock disk encryption) filelike-zip-tar (files are stored in encrypted archives) which are in some other crypted file mounted as partition (archives mounted as partitions) all on the same system So it will be slow but it would be extremely difficult to crack the encryption. So to say if you stole the server. Then i only need to make the connection like ssh safer with single use passwords, block all incoming and outgoing connections but give one "exception" for myself. And maybe one for if i somehow lose my identity for the "exeption" What other overkill but realistic security options are available, i have heard about SElinux?

    Read the article

  • 2010 MBP HD speed sanity check?

    - by hvgotcodes
    I have a 2010 MBP with the 7200 rpm hard drive. I was copying a 2.1GB file, and noticed read/write speeds of around 20MB/s. Is that reasonable? Seems slow to me.... What is the proper way to benchmark a HD on OS X? Googling I see xbench, but that hasn't been updated in years. I also see some guides for using the command line. The goal would be to benchmark my drive and then compare the results to some official scores that the drive should be getting.

    Read the article

  • Nginx: Loopback connection via PHP's getimage size crashes server (Magento's CMS)

    - by Alex
    We were able to trace down a problem that is crashing our NGINX server running Magento until the following point: Background info: Magento Backend has a CMS function with a WYSIWYG editor. This editor loads some pictures via a controller in magento (cms/directive). When we set the NGINX error_log level to info, we get the following lines (line break inserted for better readability): 2012/10/22 18:05:40 [info] 14105#0: *1 client closed prematurely connection, so upstream connection is closed too while sending request to upstream, client: XXXXXXXXX, server: test.local, request: "GET index.php/admin/cms_wysiwyg/directive/___directive/BASEENCODEDIMAGEURL,,/ HTTP/1.1", upstream: "fastcgi://127.0.0.1:9024", host: "test.local" When checking the code in the debugger, the following call does never return (in ´Varien_Image_Adapter_Abstract::getMimeType()` # $this->_fileName is http://test.local/skin/adminhtml/base/default/images/demo-image-not-existing.gif` # $_SERVER['REQUEST_URI'] = http://test.local/admin/cms_wysiwyg/directive/___directive/BASEENCODEDIMAGEURL list($this->_imageSrcWidth, $this->_imageSrcHeight, $this->_fileType, ) = getimagesize($this->_fileName); The filename requests is an URL to the same server which is requesting the script a link to a static .gif that is not existing. Sample URL: http://test.local/skin/adminhtml/base/default/images/demo-image-not-existing.gif When the above line executed, any subsequent request to the NGNIX server does not respond any more. After waiting for around 10 minutes, the NGINX server starts answering requests again. I tried to reproduce the error with a simple test script that only calls getimagesize() with the given URL - but this not crash. It simple leads to an exception saying that the URL could not be loaded (which is fine as the URL is wrong)

    Read the article

  • Setup shared internet connection on virtualbox with fixed IP

    - by Tom
    I am a web developer and until recently I have been using ubuntu as my OS. For many reasons, I have switched back to windows. I still want to keep my server on linux platform, so I setup my local server as a virtual machine. Everything works great, but i have a little struggle with the networking. Since I am working in different places and going around clients, I connect to all sorts of network with different settings. That means the possible IP range is very dynamic which causes issues when I work on my local server. At the moment I have a dynamic IP on my host and static IP on my guest. That way I can access the server from my host (by adding record to hosts file). I also have internet connection on the guest. But once i change networks, it does not work (assuming the network has different configuration). My question is, how to setup host-guest networking, so no matter what network I connect to, I can keep my static IP on guest, which is registered in hosts file on my host so I can access the webserver and also I will have internet connection on the guest? Hope it make sense. Thank you

    Read the article

  • RAID setup for maximizing data retention and read speed

    - by cat pants
    My goals are simple: maximize data retention safety, and maximize read speeds. My first instinct is to do a a three drive software RAID 1. I have only used fakeraid RAID 1 in the past and it was terrible (would have led to data loss actually if it weren't for backups) Would you say software raid 1 or a cheap actual hardware raid card? OS will be linux. Could I start with a two drive raid 1 and add a third drive on the fly? Can I hot swap? Can I pull one of the drives and throw it into a new machine and be able to read all the data? I do not want a situation where I have a raid card fail and have to try and find the same chipset in order to read my data (which i am assuming can happen) Please clarify any points on which it sounds like I have no idea what I am talking about, as I am admittedly inexperienced here. (My hardest lesson was fakeraid lol) Thanks!

    Read the article

  • Redirect traffic to local address so iOS speedtest app measures LAN speed

    - by ivan_sig
    I have mounted a Speedtest Mini server on a local LAMP, so I can test my LAN speeds effortlessly just by opening the URL with a Flash enabled web browser, the thing is, I want my iOS and Android devices to test with the LAN server too, not with the WAN, as I'm trying to measure LAN-Only performance. Is there a way so I can redirect the traffic intended to an specific external IP (The one of the real server) to my local server?. I know the servers IP as a short Wireshark analysis gave me the data, but still searching for a way to make that redirect. I have Jailbreak and root on my devices, so playing with system files is not a problem. I've tried mounting a proxy and making redirects by the hosts file and domain names, but it looks like Ookla's app relies on IP address only.

    Read the article

  • Hard drive write speed - finding a lighter antivirus?

    - by Shingetsu
    I recently have been getting a lot of system lag here (for example, the mouse and the display in general take about 15 seconds to react in the worst cases). After a lot of monitoring the resources, I found that the problem mainly happens when too much Disk I/O is being done. Three culprits have been identified: My browser had the highest write I/O with 35,000,000 I/O Write Bytes. Steam had the highest read I/O (when IDLE!!!) with 106,000,000 I/O Read Bytes. My antivirus (in both cases I will soon mention) was the runner up in both cases with: 30,000,000ish write and 80,000,000ish read. The first AV I had was Avast! which I had liked on my previous system. After noticing it taking so much I/O I switched to Panda (supposing it wouldn't use TOO much during idle phase). However it only used a bit less I/O. Just a lot less memory and cpu and somewhat more network. My browser at the moment is Maxthon 3 (which I like a lot). Before this I was running chrome which had similar data and much higher cpu when running in the background was enabled. I'm not going to be running steam all the time and there aren't many alternatives to it. I like my browser very much, but I AM willing to switch if there's an obvious problem (I'm in programming, however I'm not a very good sysadmin, especially not when it comes to windows). Finally, my system almost stops lagging when I turn off the antivirus (and preferably steam) (some remains but once in every 5-6 hours for a few seconds so it isn't a big problem). My question (has a few parts): Is it possible to configure steam to lower it's I/O usage? (and maybe network while we're at it?) Which antivirus (very preferably free) uses lowest I/O while idle (I leave PC alone during active scans so that isn't a problem). Is there an obvious problem with my current browser and, if so, is there a way to fix it or should I switch and, if so, to what? (P.S. I've been on FFox for some time too). Info on system: Windows 7 (32 bit T_T, I am getting a new one in a few months but I want to keep using system during that time though). Hard Drive (main) is a Raid0. (Also have an external 1TB one which contains steam (and steam alone). As such it doesn't get used by much anything other than steam and isn't a very large problem. However steam still uses some I/O of registry) CPU: Intel(R) Core(TM)2 CPU [email protected] RAM: 6GB (3.25GB usable) (this and CPU have little effect as shown in next section) Additional info: Memory usage during problematic times: 44% CPU usage during problematic times: 35% Page File: main drive: system managed. 1TB drive: none. The current system I'm using is about 6 years old and is mainly a place holder while I await the new one in a few months. Final words: this is my 1st post on Super User (this question wouldn't feel right on Stack Overflow where I usually stay). If it doesn't have it's place here please tell me. If anything is wrong with it, same. Edit Technically I'm looking for a live thread detection program with minimal IO usage. I already have good active scan capability: Kaspersky (the free scanner uses the paid database) and MalwareBytes. Edit 2 Noticed another one, it seems that windows media player has been using stuff even when off! Turning it off and restarting now. If the problem is fixed I'll tell you guys. The reason I didn't notice it before was because I didn't have resource manager in front of me at the MOMENT of the problem. Now I did and it was at the very top of the list!

    Read the article

  • Can my PC run Need for Speed Shift

    - by John
    Here are my PC's specs: Operating System MS Windows 7 32-bit CPU Intel Mobile Core 2 Duo T8100 @ 2.10GHz Penryn 45nm Technology RAM 3.0GB Dual-Channel DDR2 @ 332MHz 5-5-5-15 Motherboard Sony Corporation VAIO (N/A) Graphics Nvidia Defaul @ 1280x800 256MB GeForce 8400M GT (Sony) Hard Drives 250GB Hitachi Hitachi HTS542525K9SA00 ATA Device (IDE) Optical Drives Optiarc DVD RW AD-7560A ATA Device Audio High Definition Audio Device

    Read the article

  • Configure X connections over TCP without using an X connection

    - by Darren Cook
    I want to run a GUI application on a remote machine I only have ssh access to. I don't need to, or want to, see the GUI window. (I know I could use something like ssh -C -X remote_server if I wanted the GUI to be on my client.) I know X is running on the remote machine, as ps shows this: root ... /usr/bin/Xorg :0 -br -audit 0 -auth /var/gdm/:0.Xauth -nolisten tcp vt7 I set DISPLAY=:0.0 but I then get "Xlib: connection to ":0.0" refused by server" when I try to use it. At Get remote x display working in linux without ssh tunneling and Xserver doesn't work unless DISPLAY=0.0 I see the advice to use gdmsetup to allow X to listen on TCP. But, gdmsetup is a GUI application! And trying to run it over ssh -X did not work ("X11 connection rejected because of wrong authentication"). So, is there a text file I can edit to remove -nolisten? And, after editing it, how do I safely restart X, remotely? (There is other stuff running on this machine, so requesting a reboot is possible, but undesirable.) If not, should gdmsetup be able to run over ssh and I should persevere in that direction? UPDATE: I had to do the ssh -X session as root (ssh as a normal user, then sudo or su, does not work.) So, I did the edit with gdmsetup. I then restarted X with gdm-restart. I've also done xhost + from that ssh -X session. The ps line no longer shows the -nolisten tcp part. But still no luck connecting to it, with either DISPLAY=:0 or DISPLAY=localhost:0

    Read the article

  • Up-to-date Comparison of High-Speed USB Flash Drives

    - by Zoredache
    I am looking for comparison of the performance of USB flash drives. I have found several older comparisons, but I am trying to find a more up-to-date comparisons that apply to the larger storage sizes (32-128GB). I can try looking up the specs of various drives, but vendors have been known to exaggerate, or use numbers that are on accurate in tests that do not reflect actual usage. I was hoping to find 3rd party site which had perform testing.

    Read the article

  • troubleshooting postifx -> exchange connection issues

    - by Systemspoet
    I have three linux-based mail routers that run postfix and relay mail to our on-premise exchange server as well as to outlook.com, splitting the mail based on ldap atttributes. What I've observed sporadically since upgrading this spring from Exchange 2007 to 2010 is that all three of the mail relays will, for about 20 minutes, fail to connect to exchange. Postfix logs it as "lost connection with exchange.contosso.edu" ; this problem almost always occurs to all three mail relays at the same time, and lasts for slightly under 20 minutes. If I can catch it while it's occuring, and I manually do "telnet exchange.contosso.edu 25" from one mail relay and force a message through (helo, mail from, rcpt to, data, etc), then it clears that relay up. The exchange "server" is actually two machines with the HT role on them, load balanced via windows NLB. I've worked pretty hard to figure out what's happening from the postfix side and I can't see any evidence of any misbehavior. My question is, how do I attack the problem from the exchange side? Is there a connection log, or a debug setting, or something I can do to log all of the inbound connections and tell me what's causing exchange to drop them?

    Read the article

  • How do you permanently disable the 'This Connection is Untrusted' page on Firefox

    - by TheIronChef9
    I'm going insane. Can someone please help me to COMPLETELY DISABLE the 'This Connection is Untrusted' page on Firefox. Facts: I am running Firefox 23.0 on an Ubuntu machine (downloaded and installed ubuntu today) It is a work computer and I have to use my employer's proxy While visiting Webpages/webapps like Gmail or Google brings up the 'This Connection is Untrusted' page and I have to go through the whole tedious task of selecting 'I understand the Risks' and add Exceptions, etc. etc. The fact is, I don't care about the risks. I would rather this computer melt into the ground than have to see that page ever again. I want to dance naked in untrusted pages and not give a damn about the consequences. I just never want to see that page again. Ever. For some sites (eg. wikipedia), the css doesn't load and I end up seeing them in plain text. As a result these sites are completely useless. Wasted hours trying to solve this for stackoverflow.com. These issues happen on the Firefox on my Windows XP machine as well (also using the same proxy). I don't want to export/import certificates or create exceptions for every site that shows this bloody page. I just want this page gone. I don't want Firefox to tell me what's safe and what's not. Also, my system time and date are correct. I've also tried the lies on this page too with no good results. Edit: I've also tried the whole going into the Advance-Certificates-validation setup page and unchecked 'Use the Online Certificate Status Protocol (OCSP) to confirm the current validity of certificates' checkbox. Nothing happened even after restarting firefox or rebooting. I need help. Thanks.

    Read the article

  • IIS 6.0 https not working "connection was reset"

    - by cad
    Application Server Windows Server 2003 SP2 with IIS 6.0 IIS has a "Default Web Site" (port 18000, ssl 443, ID=1) with a certificate created by me. I have an specific site called "scj.galaxy.Weekly" (port 80, ssl 443, ID=1272369728) that is working fine. I have an entry in windows/system32/drivers/etc/hosts that links galaxy.Weekly.scjdev.ds to the server ip in both my local machine and in the application Server. These sites works: http://scj.galaxy.weekly/test.html works http://scj.galaxy.weekly/test.aspx works But https://scj.galaxy.weekly/test.html fails Error message is: The connection was reset The connection to the server was reset while the page was loading. The certificate was working fine for months. It was created with something similar to this: Selfssl /N:CN=*.scjdev.ds /V:3650 /S:1 /P:443 I have tried several options and none of them are working: 1) Create a certificate only in "Default Web Site" and link it to SecureBindings with command prompt cscript adsutil.vbs set /w3svc/1272369728/SecureBindings ":443:galaxy.Weekly.scjdev.ds" 2) Create a certificate only in "Galaxy Site" and link it to SecureBindings 3) Create a certificate in both and link them to secureBindings. Probably I am missing an step or something, but I can't see it. Here is the relevant config of Galaxy Site: <IIsWebServer Location ="/LM/W3SVC/1272369729" AuthFlags="0" LogPluginClsid="{FF160663-DE82-11CF-BC0A-00AA006111E0}" SSLCertHash="c36a514a0be90fbc121d9c19bb052842289d5aee" SSLStoreName="MY" SecureBindings=":443:galaxy.Weekly.scjdev.ds" ServerAutoStart="TRUE" ServerBindings=":80:galaxy.Weekly.scjdev.ds" ServerComment="galaxy.Weekly.scjdev.ds" > </IIsWebServer> <IIsWebVirtualDir Location ="/LM/W3SVC/1272369729/root" AccessFlags="AccessRead | AccessScript" AppFriendlyName="Default Application" AppIsolated="2" AppRoot="/LM/W3SVC/1272369729/Root" AuthFlags="AuthAnonymous | AuthNTLM" DefaultDoc="Default.aspx" DirBrowseFlags="EnableDirBrowsing | DirBrowseShowDate | DirBrowseShowTime | DirBrowseShowSize | DirBrowseShowExtension | DirBrowseShowLongDate" Path="D:\Webs\Galaxysite" ScriptMaps="some config... " > </IIsWebVirtualDir>

    Read the article

  • Connection reset to some websites

    - by user143271
    I'm using a 2wire 3600HGV modem/router. Starting around this afternoon, any time I try to access anything from i.imgur.com I get The connection to i.imgur.com was interrupted in chrome, and the actual error is Error 101 (net::ERR_CONNECTION_RESET). It's network wide (tested multiple browsers on multiple computers and phones). I can access imgur.com just fine, but nothing from its content server i.imgur.com. If I disable wifi on my phone and use its 4G connection, I can access it just fine, so obviously imgur isn't down. I haven't changed any configuration on the router, and I have tried changing DNS servers (I tried google and OpenDNS). It also seems that imgur is not the only site; howtogeek and a couple of others seem to have the same problem. It looks like they are all edgecast cdn content servers, but not all edgecast cdn servers fail. Tumblr, for instance, works just fine. Does anyone have any idea what would be causing this? EDIT: Related to the edgecast remark, it would appear that this is a specific edgecast server: gs1.wpc.edgecastcdn.net. Tumbler's content is on gs1.wac.edgecastcdn.net, so it might be on a different server. Edit #2: These sites all respond to ping just fine as well.

    Read the article

  • Copy past speed very slow for a large number of files on Windows [closed]

    - by Arno2501
    I've run the following test I've created a folder containing 15'000 files of 400 bytes using this batch : @ECHO off SET times=15000 FOR /L %%i IN (1,1,%times%) DO ( fsutil file createnew filename%%i.txt 400 ) then I copy past it on my Windows Computer using this command : robocopy LargeNumberOfFiles\ LargeNumberOfFiles2\ After it has completed I can see that the transfer rate was 915810 Bytes/sec this is less than 1 MB/s. It took me several seconds to copy 7 MBytes Please note that this is very slow. I've tried the same with a folder with a single file of 50 Mbytes and the transfer rate is 1219512195 Bytes/sec. (yeah GB/s) instantaneous. Why copying large number of files take so much time - ressources on a windows filesystem ? Please note that I've tried to do the same on a linux system which runs on the same computer in a virtual machine (vmware player) with ext3 filesystem. I use the cp command and the copy is instantaneous ! Please also note the following : no antivirus I've tested that behaviour on multiple windows computers (always ntfs) i always get comparable results (transfer rate under 1MB/s avg 7-8 seconds to copy 7 MBytes) I've tested on multiple linux ext3 system the copy is always instantaneous for that amount (15000 files of 400 bytes) The question is about understanding what makes windows filesystem so slow to copy large number of files compared to a linux one for instance.

    Read the article

  • How do I connect to SDF on a Mobile device from desktop application?

    - by pitprog
    C# WinForms .Net 3.5 to SQL CE 3.5 on Mobile 6.1 Device I'd like to make a connection from a desktop application to a SDF database on my Windows Mobile device while it's connected via ActiveSync. Visual Studio lets me create a Data Connection to my device. The connections tests OK and I can view the data in the database using Visual Studio. I then create a form and try to fill a DataGridView. When I run the program I get an error that the path to the data base is not valid. How am I supposed to specify the Mobile device path in the connection string? In my App.Config, I've tried variations on the path, but none of them work: connectionString="Data Source=Mobile Device\Program Files\SqlCeViaActiveSync\Orders.sdf" connectionString="Data Source=\Mobile Device\Program Files\SqlCeViaActiveSync\Orders.sdf" connectionString="Data Source=Program Files\SqlCeViaActiveSync\Orders.sdf" connectionString="Data Source=\Program Files\SqlCeViaActiveSync\Orders.sdf" The full connection string section looks like this: <connectionStrings> <add name="SqlCeViaActiveSync.Properties.Settings.OrdersConnectionString" connectionString="Data Source=Mobile Device\Program Files\SqlCeViaActiveSync\Orders.sdf" providerName="Microsoft.SqlServerCe.Client.3.5" /> </connectionStrings> Also, I did make a reference to Microsoft.SqlServerCe.Client, as I found a few articles that mentioned it was necessary. Can anyone point me to some recent articles/samples or let me know what I'm doing wrong? Thanks!

    Read the article

  • How to set up hibernate to use Glassfish connection pool?

    - by jschoen
    I have set up a connection pool in Glassfish with a jndi resource for it also setup. I am stumped on how to configure hibernate to go get it. I have come across alot of write ups to configure it to use C3P0 connection pool. Well I am lost. I found that I need to set: hibernate.connection.datasource hibernate.jndi.url hibernate.jndi.class hibernate.connection.username hibernate.connection.password Would datasource be the same as the hibernate.connection.datasource set in the connection pool? What would hibernate.jndi.class be? Are hibernate.connection.username and hibernate.connection.password for the connection to the database or to the appserver? I assume this is to the database, but why do I need them since that is all set in the appserver?

    Read the article

< Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85  | Next Page >