Search Results

Search found 29426 results on 1178 pages for 'user99572 is fine'.

Page 78/1178 | < Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85  | Next Page >

• Internet Timeouts with TP-Link TL-WN821N v2 wireless usb stick

  - by user1622959

  A short time after accessing the internet, the browser/download times out. Before the timeout, the internet works OK briefly; afterwards, the wireless is still connected with a strong signal, but every internet access results in a timeout. When I leave the PC for a while, the internet is back just to timeout again as soon as I start using it. The same happens when I reconnect to the router. Also, when I surf the internet, it takes a couple of minutes until the timeout, but when I download something, it times out in a matter of seconds. The wireless adapter works just fine in Windows and internet via ethernet cable works just fine in Ubuntu. Does anyone have the same problem or knows a solution. I use Ubuntu 12.10 x64. The problem occurs since I installed ubuntu (which was a few days ago). Here some stuff that might be usefull: serus@serus-Ubuntu-PC:~$ lsusb Bus 002 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170] serus@serus-Ubuntu-PC:~$ lsmod Module Size Used by carl9170 82083 0 serus@serus-Ubuntu-PC:~$ modinfo carl9170 filename: /lib/modules/3.5.0-21- generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko alias: arusb_lnx alias: ar9170usb firmware: carl9170-1.fw description: Atheros AR9170 802.11n USB wireless serus@serus-Ubuntu-PC:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"virginmedia0137463" Mode:Managed Frequency:2.462 GHz Access Point: A0:21:B7:F8:29:B6 Bit Rate=240 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:1399 Invalid misc:18 Missed beacon:0 serus@serus-Ubuntu-PC:~$ sudo lshw -C network *-network description: Wireless interface physical id: 1 bus info: usb@2:2 logical name: wlan0 serial: 00:27:19:bb:00:19 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.5.0-21-generic firmware=1.9.4 ip=192.168.0.6 link=yes multicast=yes wireless=IEEE 802.11bgn

  Read the article

• Problems syncing photos and strange effects of uploaded files from other devices

  - by Daniel

  I have a Galaxy Spica (GT-i5700) Android v2.1, rooted with Leshak dev 7 #123. But never mind the root info, the problem would be the same unrooted. The photos from this phone is stored in "sdcard/images", nevertheless the phone also creates a "sdcard/DCIM" but only stores some thumbnails there. Problem nr 1: U1 only reads the DCIM-folder for automatic photo-upload. So photos stored in this phone is not uploaded. If I move photos to "DCIM" folder, U1 recognises the photos and start uploading them. Possible solution: Could there be an option in the settings, to set preferred photo folder? Problem nr 2: Out of 74 pictures, 12 did not get uploaded. Pressing "Retry failed transfers" in Settings does nothing. Pressing the files where status is "Upload failed, tap to retry" only changes the status to "Uploading..." but nothing gets uploaded. If I upload another file to U1, it is uploaded directly without any problem. It has nothing to do with file size, 1,1 MB files has been uploaded fine whilst some failed are 0,8 MB. Problem nr 3: The photos from DCIM are in my case uploaded to a folder called "Pictures - GT-I5700" in U1. If I log in to the homepage and from there upload another photo in "Pictures - GT-I5700", it shows up in U1 on my phone fine. But when I tap it, U1 downloads the photo to "sdcard/U1/Pictures - GT-I5700". If it sync photos from "sdcard/DCIM" to a specific folder, why not also download files to the same folder from which it is synced? After a while of usage, syncing and uploading files from different clients it would be a mishmash of folders and places files are stored and considering that I see no use of U1 at all. Another question: If my SD card in some way breaks down/some folders cannot be read/card temporarly changed and U1 is running, does U1 consider that as files deleted and also delete from the cloud?

  Read the article

• Keyring no longer prompts for password when SSH-ing

  - by Lie Ryan

  I remember that I used to be able to do ssh [email protected] and have a prompt asks me for a password to unlock the keyring for the whole GNOME session so subsequent ssh wouldn't need to enter the keyring password any longer (not quite sure if this is in Ubuntu or other distro). But nowadays doing ssh [email protected] would ask me, in the terminal, my keyring password every single time; which defeats the purpose of using SSH keys. I checked $ cat /etc/pam.d/lightdm | grep keyring auth optional pam_gnome_keyring.so session optional pam_gnome_keyring.so auto_start which looks fine, and $ pgrep keyring 1784 gnome-keyring-d so the keyring daemon is alive. I finally found that SSH_AUTH_SOCK variable (and GNOME_KEYRING_CONTROL and GPG_AGENT_INFO and GNOME_KEYRING_PID) are not being set properly. What is the proper way to set this variable and why aren't they being set in my environment (i.e. shouldn't they be set in default install)? I guess I can set it in .bashrc, but then the variables would only be defined in bash session, while that is fine for ssh, I believe the other environment variables are necessary for GUI apps to use keyring.

  Read the article

• Exalogic Elastic Cloud Software (EECS) version 2.0.1 available

  - by JuergenKress

  We are pleased to announce that as of today (May 14, 2012) the Exalogic Elastic Cloud Software (EECS) version 2.0.1 has been made Generally Available. This release is the culmination of over two and a half years of engineering effort from an extended team spanning 18 product development organizations on three continents, and is the most powerful, sophisticated and comprehensive Exalogic Elastic Cloud Software release to date. With this new EECS release, Exalogic customers now have an ideal platform for not only high-performance and mission critical applications, but for standardization and consolidation of virtually all Oracle Fusion Middleware, Fusion Applications, Application Unlimited and Oracle GBU Applications. With the release of EECS 2.0.1, Exalogic is now capable of hosting multiple concurrent tenants, business applications and middleware deployments with fine-grained resource management, enterprise-grade security, unmatched manageability and extreme performance in a fully virtualized environment. The Exalogic Elastic Cloud Software 2.0.1 release brings important new technologies to the Exalogic platform: Exalogic is now capable of hosting multiple concurrent tenants, business applications and middleware deployments with fine-grained resource management, enterprise-grade security, unmatched manageabi! lity and extreme performance in a fully virtualized environment. Support for extremely high-performance x86 server virtualization via a highly optimized version of Oracle VM 3.x. A rich, fully integrated Infrastructure-as-a-Service management system called Exalogic Control which provides graphical, command line and Java interfaces that allows Cloud Users, or external systems, to create and manage users, virtual servers, virtual storage and virtual network resources. Webcast Series: Rethink Your Business Application Deployment Strategy Redefining the CRM and E-Commerce Experience with Oracle Exalogic, 7-Jun@10am PT & On-Demand: ‘The Road to a Cloud-Enabled, Infinitely Elastic Application Infrastructure’ (featuring Gartner Analysts). WebLogic Partner Community For regular information become a member in the WebLogic Partner Community please visit: http://www.oracle.com/partners/goto/wls-emea ( OPN account required). If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Mix Forum Wiki Technorati Tags: ExaLogic Elastic Cloud,ExaLogic,WebLogic,WebLogic Community,Oracle,OPN,Jürgen Kress,ExaLogic 2.0.1

  Read the article

• "Unable to install GRUB in /dev/sda" when installing GRUB

  - by vicban3d

  I recently bought a shiny new Lenovo Yoga 2 Pro and I want to dual boot it with Ubuntu for studying purposes. Its built-in OS is Windows 8.1 and it has a 256GB SSD. I've made a separate 90GB partition just for Ubuntu and a live USB to install it. The first time everything seemed to work great, I solved the wifi issued by blacklisting ideapad_laptop, the installation went flawlessly and Ubuntu worked fine. When I got up the next morning and turned on my laptop it booted into Windows right away without ever showing the GRUB menu. So I tried to reset, and checked my partitions with the Disk Manager and everything looked fine. Since I couldn't find a solution online I went ahead and formatted the partition to try and install again. This time and every time since, the installation was aborted and I got a fatal error saying: Unable to install GRUB in /dev/sda Executing `grub-install /dev/sda` failed. This is a fatal error. Can anyone please suggest a solution to this problem? If any further information is needed I would be happy to provide it. Thanks. When installing I get the following in details: ubuntu kernel: [ 1946.372741] FAT-fs (sda2): error, fat_get_cluster: invalid cluster chain (i_pos 0). ubuntu grub-installer: error: Running 'grub-install --force failed.

  Read the article

• Problem with wake after suspend using USB remote.

  - by Bod

  Hi, I'm a linux newbie looking for some help. I'm currently setting up an XBMC HTPC using a laptop and 10.10 and all works great except for waking from resume using the power button on the remote. The suspend works from remote works fine as does the resume using the power button on the laptop. I've checked /proc/acpi/wakeup which initially showed the following. Device S-state Status Sysfs node C096 S5 *disabled pci:0000:00:1e.0 C0F1 S3 *disabled pci:0000:00:1d.0 C0F8 S3 *disabled pci:0000:00:1d.1 C0F9 S3 *disabled pci:0000:00:1d.2 C0FA S3 *disabled pci:0000:00:1d.3 C0FB S3 *disabled pci:0000:00:1d.7 C102 S5 *disabled pci:0000:00:1c.0 C22B S5 *disabled pci:0000:08:00.0 C115 S5 *disabled pci:0000:00:1c.2 C22C S5 *disabled C118 S5 *disabled pci:0000:00:1c.3 C22C S5 *disabled I've since configured the above so that the S3 devices above are enabled. I've confirmed that they are the correct devices using lspci 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) None of this has worked unfortunately and I'm now stuck. It simply refuses to wakeup from the remote. The USB receiver shows no activity LED while suspended. Suspend/resume from the remote works fine from Windows 7 so I know the laptop is ok with it. Any ideas? I need to get this sorted to gain Wife Approval for this system. Thanks, Bod.

  Read the article

• SD card won't appear after upgrade to 13.10

  - by Pixel

  My SD card won't mount when I put it into my lap top, everything was fine before the upgrade. The information about the SD card appears just fine when I type "sudo fdisk l " it just says that it doesn't have a valid partition table. When I type "_sudo blkid" I get the following answer: /dev/sda1: UUID="CCA8-9030" TYPE="vfat" /dev/sda2: UUID="8a1d135b-384b-432d-b608-64dcf09ada24" TYPE="ext2" /dev/sda3: UUID="7s6PtU-kj2Z-N8XD-0mzl-840i-i3HG-enlbAf" TYPE="LVM2_member" /dev/sr0: LABEL="Bamboo CD" TYPE="iso9660" /dev/mapper/ubuntu--vg-root: UUID="c9b521c8-7c9f-493b-95c8-a7d79c465318" TYPE="ext4" /dev/mapper/ubuntu--vg-swap_1: UUID="7f155ab6-e1b9-485b-a2bc-443c0622284d" TYPE="swap" When I use lsusb: Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 13d3:5710 IMC Networks UVC VGA Webcam Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 002: ID 046d:c52f Logitech, Inc. Unifying Receiver Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub I've read the other threads and I couldn't really find any good answers, my card reader was compatible with the previous version of ubuntu, so technically it should still be compatible with the next version. Also I can't erase what's on the card, it contains important data which I need... :/ If you need anymore information just ask, I'll give it as soon as I can. Pixel.

  Read the article

• Tomcat + Spring + CI workflow

  - by ex3v

  We're starting our very first project with Spring and java web stack. This project will be mainly about rewriting quite large ERP/CRM from Zend Framework to Java. Important factor in my question is that I come from php territory, where things (in terms of quality) tend to look different than in java world. Fatcs: there will be 2-3 developers, at least one of developers uses Windows, rest uses Linux, there is one remote linux-based machine, which should handle test and production instances, after struggling with buggy legacy code, we want to introduce good programming and development practices (CI, tests, clean code and so on) client: internal, frequent business logic changes, scrum, daily deployments What I want to achieve is good workflow on as many development stages as possible (coding - commiting - testing - deploying). The problem is that I've never done this before, so I don't know what are best practices to do this. What I have so far is: developers code locally, there is vagrant instance on every development machine, managed by puppet. It contains the same linux, jenkins and tomcat versions as production machine, while coding, developer deploys to vagrant machine, after local merge to test branch, jenkins on vagrant handles tests, when everything is fine, developer pushes commits and merges jenkins on remote machine pulls commit from test branch, runs tests and so on, if everything looks green, jenkins deploys to test tomcat instance Deployment to production is manual (altough it can be done using helping scripts) when business logic is tested by other divisions and everything looks fine to client. Now, the real question: does above make any sense? Things that I'm not sure about: Remote machine: won't there be any problems with two (or even three, as jenkins might need one) instances of same app on tomcat? Using vagrant to develop on php environment is just vise. Isn't this overkill while using Tomcat? I mean, is there higher probability that tomcat will act the same on every machine? Is there sense of having local jenkins on vagrant?

  Read the article

• Ethernet Connection Unavailable

  - by fabikw

  I'm running Ubuntu Server 12.04 on a laptop with an Intel NIC (driver e1000e). When I connect the ethernet port to the internet (college network, DHCP) it works out of the box. Now I'm trying to connect it to a networked USRP (if you want to know what it is). A friend of mine managed to do this in his laptop (running regular Ubuntu 12.04) just by setting up a new Wired connection in the Network Manager with appropriate addresses. However, when I do the same, no wired connections are available. The output of nmcli -p dev is =========================================== Status of devices =========================================== DEVICE TYPE STATE ------------------------------------------- wlan0 802-11-wireless connected eth0 802-3-ethernet unavailable but the cable is connected to the device and the device is powered up. Any idea how to solve this? UPDATE: After stopping the network-manager service, setting up the connection manually and starting the service again, it now detects the ethernet connection. However, the device still can't receive data and doesn't answer to pings. UPDATE 2: As suggested I tried using a cross over cable but the result is exactly the same. However, I found out that connecting the device to the dock (as opposed to directly to the laptop) works fine. I know that the ethernet port in the laptop works fine, because connecting to the network through it works. Is it possible that the port in the laptop doesn't support Gb Ethernet (because that's what the device requires) but the one in the dock does?

  Read the article

• Network print to brother MFC-7420

  - by trampster

  I am trying to pint to a Brother MFC-7420 from my ubuntu 10.04 machine. The brother is attached to a windows XP machine and is shared. This is what I have tried: System-Administration-Printing, Add, Expand Network Printer, Windows Printer via SAMBA, Browse (I can find the printer no problems here), Foward, Choose Driver Dialog, Brother, My printer is not in this list So the next thing I tried was to download the printer driver from here http://welcome.solutions.brother.com/bsc/public_s/id/linux/en/download_prn.html The driver installed fine but my printer still does not appear in the list. I also tried installing the cups wrapper but that gave the following error. Restarting Common Unix Printing System: cupsd [ OK ] cp: cannot stat `/usr/share/cups/model/MFC7420.ppd': No such file or directory dpkg: error processing cupswrappermfc7420 (--install): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: cupswrappermfc7420 I tried connecting the printer directly but even though I have installed the driver, when I go to printers and click on the printer (it shows up fine as a USB printer) then it say searching for drivers and then gives me a list, this is the same list as before which doesn't have my printer. It really shouldn't be this hard. on window you don't have to installing anything it just works and the same is true for my brothers Mac. How do I print to my printer?

  Read the article

• Ubuntu 12.04 desktop, VNC viewer not refreshing screen

  - by user73279

  I've had this issues across multiple machines and multiple versions of Ubuntu desktop (all 10.04 or later). Usually it happens with an old laptop I've put Ubuntu on but now it's happening on my primary dev machine (a quad-core PC recently upgraded to Ubuntu 12.04 desktop). The problem is this - I can connect to the machine and login with the password, the initial screen looks fine but never refreshes. I can see the monitor for the machine across the room and can see the mouse move and the menus pop up but the image of the screen on the PC in front me running the VNC viewer never updates. So the mouse and keyboard commands are working. Ubuntu 12.04 Desktop Ultra VNC Viewer (also seen with RealVNC's free VNC viewer) Desktop Sharing Static IP on eth0; Dynamic ID on eth1 I think it is an Ubuntu config issue because this PC used to work just fine with 9.04, 10.04, and 11.10 (over the past couple of years). I've also had a couple of laptops that used to have this issue with older Ubuntu's but don't with 12.04. Additional info: The Win7 PC I'm trying to use to control the Ubuntu PC is connected via 2 DLink 8-port gigabit routers. The Ubuntu laptop I usually control via VNC is typically only connected to the network via wireless. The screen refresh is choppy but usable. I've repeated the issue on a Win7 laptop which was connected via ethernet and wireless.

  Read the article

• Laptop Display Not Working

  - by etrask

  Hello, I just purchased this laptop. It is working fine but I want to use Xubuntu on it. I managed to get 10.04 installed and running but it did not recognize/use the wireless card. So I want to try 10.10. However, every time I try, the screen goes black and never comes back on. I have tried the Live CD and Alternate install CDs, for both Ubuntu and Xubuntu 10.10. After I select "Install Ubuntu" or "Try Ubuntu", the screen blacks out and never displays anything. So I deleted "quiet" and "splash" off the command line to see what messages would come up. A bunch of text flies by but it ends at: [time] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [time] TCP bind hash table entries 65536 (order: 8, 1048576 bytes) [time] TCP: Hash tables configured (established 524288 bind 65536) [time] TCP reno registered [time] UDP hash table entries: 2048 (order: 4, 65536 bytes) [time] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [time] NET: Registered protocol family 1 And freezes here forever. I have tried nomodeset, vga=771, and xforcevesa with no progress. Is my video card simply not going to work with this distro? It seems strange that 10.04 would work fine but not 10.10. Any help is appreciated, thank you.

  Read the article

• ProStar gaming laptop, which had Ubuntu 10.10, won't boot past Grub. Thoughts?

  - by Richard Zak

  At work we have some high-end gaming laptops we use for their dual GPUs. The machines have second generation i7 CPUs, and came with Windows 7. On most of them I installed Ubuntu 10.10, and all was fine. There were two laptops that I wanted to repurpose and wanted to reinstall the OS. It boots the CD (burned Ubuntu installation CD, I've tried 10.10, 11.10, and 12.04, as well as CentOS 6), and when Grub tried to boot the kernel, I just get a cursor blinking in the upper left corner of the screen. I tried the disabling of ACPI and the other items in the advanced menu, but nothing works. I could still boot to the current Linux installation though. I was able to install Windows 7 again, and use WUBI, but I think that works because it uses the Windows bootloader and not Grub. How could it have worked before and not now? I have confirmed that the CD is fine, as are the hard drive and CD drive. I also had the same problem with Debian, and had to boot through Windows 7 to install it.

  Read the article

• External display resolution issue

  - by Steven

  I'm new to Ubuntu. I've 'dabbled' in the past but Windows was annoying me too much so I finally made the change. One thing I use my laptop for is outputting the screen onto an external monitor. In Windows this usually works fine (but when there is an issue, it's a pain to resolve and has crashed my computer on many occasions). In Ubuntu it's a very simple case of "plug and play" because it displays the content immediately with no major problems. However, I can only alter the resolution of the external display to 4:3 formats, whereas the external monitor is 16:9, so the picture is stretched. In Windows there's loads of resolutions to choose from. If I disable the laptop's screen, it still doesn't allow me to display the correct resolution externally (on VGA). Further to that, if I close the laptop it keeps the external screen as it is, but when I reopen the laptop, the laptop screen doesn't turn back on until I restart. If it's a video I am watching, I can use VLC to alter the aspect ratio so the video looks fine, but it's quite an annoying work around. I used terminal to find my graphics controller, which is "Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07)" (not great, I know... the laptop was a free gift with my mobile!) Any idea of how I can get the resolution on the external monitor to be correct?

  Read the article

• Ubuntu 13.10 Unity doesn't load after upgrade

  - by William

  Just upgraded to Ubuntu 13.10 only to find that Unity won't load (login freezes, after doing ctrl+alt+F1, logging in and then doing startx, I get a blank desktop and the mouse pointer, and nothing else). I can right click, but the only operations that work are "create new file" and "create new folder". For example, "change desktop background" doesn't work. Also, after doing a few right clicks and choosing "change desktop background", I get a warning message box: "compiz closed unexpectedly." Guest login works fine. Tried creating a new user, but I experience the same thing with the new user. Tried removing all configuration files from my home directory... same thing. Doing dconf reset -f /org/compiz/ gives an error "error spawning command line..." Doing unity --reset also gives errors. Tried uninstalling unity (and compiz) and reinstalling, but that doesn't help. Tried reconfiguring lightdm, didn't help. I don't have any proprietary drivers installed. Once again, the funny thing is that the guest session works fine.

  Read the article

• Forking a GPL dual licensed software with business owned copyrights

  - by Eric

  After receiving some threats of the copyrights holder of a dual licensed software(GPL2 and commercial) to buy the commercial version for projects in production, I am thinking to make a fork. In a case of GPL2 and commercially dual licensed with business owned copyrights software, is forking the GPL2 version an option? Also, is forking a good way to deal with such cases? Background information The software is a web CMS released under 2 versions a GPL2 free open source edition and a commercial edition including technical support and extra functionality. The problem is that now, basing their argumentation on the "distribution" definition of the GPL2, the company holding the copyrights argue that delivering the software and some extensions to a client is considered as a "distribution". And that such a "distribution" falls under the GPL2 obligation to release the custom made extension code. Custom made extensions are mainly designs, templates and very specific functionality. Basically they give me 3 choices: Buying the commercial licensed edition for projects based on the GPL in production, Deleting all the projects in production based on GPL2 version, Releasing all the extensions as GPL2 code. The first 2 options are nothing realistic for finished projects. The third option could be fine, but as most of the extensions are very specific, cleaning the code to make it usable by other users means lot of works and also I am not sure the clients will appreciate to have their website designs and specific functionality released publicly. The copyrights holding company even contacted some clients directly, giving them the "choice". I know that this is a very corporate interpretation of GPL2, and a such action is nothing close to legal, but as an independent developer, I don't want to take the risk to get involved in some long and tiring legal procedures. PS. This question was first asked on Stack Overflow where it felt out of the scope and closed, after reading the present site FAQ, discussing about software licensing seems fine.

  Read the article

• Internet unusably slow with Realtek Semiconductor Co., Ltd. RTL8111/8168B card

  - by user42424

  So I have recently installed Ubuntu 11.10 for a dual boot with wind 7. After the install I had like 300 updates, so I installed them. At first I could use the internet, although it was extremely slow. However now I cannot, sometimes it will load and others it will simply time out. When I try to download something it will either take forever or will not at all. This is a wired system. On Windows side my speeds are fine. Any help would be greatly appreciated. Also like I said I am new to Linux/Ubuntu so please be nice. One last thing, I also installed 11.10 for same dual boot on my laptop, and wireless speed is the same as on Windows? Only the wired desktop gives me the problem? Hear is some hardware info.. Hope it helps. Mobo: Gigabyte GA=880GMA- AMD / CPU: AMD Phenom (tm) IIx4 965 / 16 GB Ram / Realtek PCIe GBE Family Controller / Cisco Linksys E2000 / Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) / eth0 Link encap:Ethernet HWaddr 50:e5:49:33:64:cf inet addr:192.168.1.118 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe33:64cf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76722 errors:0 dropped:76722 overruns:0 frame:76722 TX packets:49692 errors:0 dropped:65 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107956638 (107.9 MB) TX bytes:4342553 (4.3 MB) Interrupt:44 Base address:0x2000 thanks to roadmr problem solved! I powered down PC, un plugged power from pc end, waited a few (maybe 3)minutes. plugged power back in, pushed and held power button for 30 + seconds. Let go, powered on PC, and my Internet is fine! downloads and web speed blaze, just like on my Win 7 boot, maybe even faster. Problem Solved, Thanks to all!! **

  Read the article

• Ubuntu on Samsung NP700Z5B - no Grub

  - by copolii

  I just bought a Samsung NP700Z5B laptop. Gorgeous machine and great performance! I do 2 things when I get a new laptop: Format the HD and install Winblows from a CD to ditch the bloatware Install some variant of Linux on it (lately Ubuntu) Step 1 worked fine (until earlier today), but I haven't been able to install Ubuntu on it for the past 3 days! I've tried Mint12, Ubuntu 12.04, Ubuntu 11.10, Ubuntu 11.04 and Ubuntu 10.04. The live CD and the installations all run fine and report no problems, but when I reboot grub is nowhere to be found! The system goes directly to Winblows! I've tried booting from the liveCD and re-installing grub via the chroot and purge & reinstall methods (https://help.ubuntu.com/community/Grub2) and neither makes a difference. I've also tried copying the boot sector: dd if=/dev/sda of=linux.bin bs=512 count=1 and putting it on c: then setting bcdedit to add the entry to the Windows bootloader with no results. Earlier today I decided to try and set my boot partition as an EFI boot partition ... bad choice, now I don't even have the Winblows boot loader. I've officially ran out of ideas. Tried calling Samsung, but they're closed (they'd probably say something stupid along the lines of "Samsung recommends Windows 7" ... I've had Dell say that to me). Any help would be greatly appreciated. Update 1 Tried re-installing 12.04 and now I get the screen continously turning off and back on, but still no sign of booting ... it has been doing it for 15 mins so far (I set the boot partition type to ext2 instead of ext4) Update 2 Well ... this just gets better and better. I inserted the installation USB key to reboot it and the flickering stopped for about a minute (remained on) then it started turning off and on again

  Read the article

• Touchpad not working on HP

  - by Grayson

  Everything worked fine in Ubuntu 10.04, flawless in fact, I admired the way the Operating System had handled such a unique touchpad so well. I have an HP Pavilion dv6. The touchpad and left, middle, and right click buttons are all on the trackpad, and it the bottom end depresses to click accordingly for each kind of click. In 10.04, everything worked fine, upon upgrading to Ubuntu 10.10 things became... odd. The scroll on the side would work, as would the left click. The right click wouldn't work however, but if you would lightly tap the exact right corner of the touchpad, the right click menu would come up, though it was inconsistent and difficult to make it do so. I have applied a fix I found on the older Ubuntu Forums for a similar issue, and it restored the normal left and right click, but it isn't as fluid, and there isn't the vertical scroll feature, which I do rather like to have... I would just like things to be as it was, if this is possible, please, please tell me how to do so. Thank you.

  Read the article

• Second Monitor Detected, but not receiving a signal after upgrading to 12.04

  - by user62458

  After I upgraded to 12.04, my second monitor is detected (in display settings), but will not power on. I have scoured the Internet and forums for a solution and I can't find anything. I have found a couple people with the same problem, but never a solution for it. I am no expert, but I'm certainly not a noob. My computer uses AMD Radeon 6250 graphics, but I do NOT want to use the proprietary graphics drivers. They refuse to work properly with my second monitor (they ATI drivers will only mirror screens, and I've done everything to try to fix it, and I DON't want mirrored screens) Not to mention that the default open-source video drivers seem to work much better than the proprietary anyway! Again, Ubuntu's default video drivers work fine, and they even DETECT the second monitor (Dell 19'). I can drag stuff off the screen and put it on the 'space' of the second monitor and even a screen-shot shows that there are two monitors active; but the monitor is OFF. It will not power on. It goes into 'power-save' mode because it is not receiving a signal. For some reason it is not getting the signal to power on, even though Ubuntu thinks the monitor is working properly. I had this working fine on my Sony VAIO yesterday (with Radeon graphics/default Ubuntu video drivers). I upgraded to a Samsung Series 3 and now I have this issue. I can't for the life of me figure out why the monitor is connected, detected and I have screen space for the monitor, but the screen won't turn on! XRANDR Output: Screen 0: minimum 320 x 200, current 1366 x 768, maximum 8192 x 8192 VGA-0 connected (normal left inverted right x axis y axis) 1440x900 59.9 + 75.0 1280x1024 75.0 60.0 1152x864 75.0 1024x768 75.1 70.1 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 640x480 72.8 75.0 66.7 60.0 720x400 70.1 LVDS connected 1366x768+0+0 (normal left inverted right x axis y axis) 344mm x 194mm 1366x768 60.1*+ 1280x720 59.9 1152x768 59.8 1024x768 59.9 800x600 59.9 848x480 59.7 720x480 59.7 640x480 59.4 HDMI-0 disconnected (normal left inverted right x axis y axis)

  Read the article

• Problems when rendering code on Nvidia GPU

  - by 2am

  I am following OpenGL GLSL cookbook 4.0, I have rendered a tesselated quad, as you see in the screenshot below, and i am moving Y coordinate of every vertex using a time based sin function as given in the code in the book. This program, as you see on the text in the image, runs perfectly on built in Intel HD graphics of my processor, but i have Nvidia GT 555m graphics in my laptop, (which by the way has switchable graphics) when I run the program on the graphic card, the OpenGL shader compilation fails. It fails on following instruction.. pos.y = sin.waveAmp * sin(u); giving error Error C1105 : Cannot call a non-function I know this error is coming on the sin(u) function which you see in the instruction. I am not able to understand why? When i removed sin(u) from the code, the program ran fine on Nvidia card. Its running with sin(u) fine on Intel HD 3000 graphics. Also, if you notice the program is almost unusable with intel HD 3000 graphics, I am getting only 9FPS, which is not enough. Its too much load for intel HD 3000. So, sin(X) function is not defined in the OpenGL specification given by Nvidia drivers or something else??

  Read the article

• Lerping to a center point while in motion

  - by Fibericon

  I have an enemy that initially flies in a circular motion, while facing away from the center point. This is how I achieve that: position.Y = (float)(Math.Cos(timeAlive * MathHelper.PiOver4) * radius + origin.Y); position.X = (float)(Math.Sin(timeAlive * MathHelper.PiOver4) * radius + origin.X); if (timeAlive < 5) { angle = (float)Math.Atan((0 - position.X) / (0 - position.Y)); if (0 < position.Y) RotationMatrix = Matrix.CreateRotationX(MathHelper.PiOver2) * Matrix.CreateRotationZ(-1 * angle); else RotationMatrix = Matrix.CreateRotationX(MathHelper.PiOver2) * Matrix.CreateRotationZ(MathHelper.Pi - angle); } That part works just fine. After five seconds of this, I want the enemy to turn inward, facing the center point. However, I've been trying to lerp to that point, since I don't want it to simply jump to the new rotation. Here's my code for trying to do that: else { float newAngle = -1 * (float)Math.Atan((0 - position.X) / (0 - position.Y)); angle = MathHelper.Lerp(angle, newAngle, (float)gameTime.ElapsedGameTime.Milliseconds / 1000); if (0 < position.Y) RotationMatrix = Matrix.CreateRotationX(MathHelper.PiOver2) * Matrix.CreateRotationZ(MathHelper.Pi - angle); else RotationMatrix = Matrix.CreateRotationX(MathHelper.PiOver2) * Matrix.CreateRotationZ(-1 * angle); } That doesn't work so fine. It seems like it's going to at first, but then it just sort of skips around. How can I achieve what I want here?

  Read the article

• How to get "Fn" keys to work (Asus 4830T)? (specificly, the "suspend" key)

  - by Pointy

  I've got an Asus 4830T onto which I've just re-installed 12.04 because I installed an SSD. I was running 12.04 before too, which had been upgraded over a few releases. At some point on that old install, I had gotten all the "Fn" keys to work, or at least all the ones I cared about. (Oh except I think the screen brightness keys never worked.) I have no recollection of what I did. Anyway now things are fine, and some of the Fn keys work: the one to turn of the trackpad and the one to turn off wireless (grr I hate that one). However, the "suspend" key for some reason does not work. Now the system will suspend and resume just fine, but I'm having to do it from the menu. Is there an easy (or hard) way to make those work? I'm running straight Ubuntu but with Xfce installed as my normal desktop. (In other words, it's not Xubuntu, though I doubt it matters.) I recall at some point having found some arcane mapping mechanism to bind the Fn keys to actions, but I can't find it now. (I'm perfectly OK with editing weird files; I'm a long-time Unix user.) (Very long-time.)

  Read the article

• How do I stop color changes when quitting vi from a terminal emulator?

  - by Michael Warhol

  I have a problem with colors when using vi under Ubuntu 12.04. I'm connecting to my Ubuntu server from a PC, using PowerTerm terminal emulation software. I have PowerTerm set up to display black text on a grey background. When I connect to the Ubuntu box, the screen is fine. When I open a file with vi, the screen is fine. The text is black on a gray background, which is normal for my PowerTerm setup. However, if the file is less than a full screen long, the remainder of the screen is a black background. When I quit vi, the entire background turns black, and the text becomes white. I have to do a Terminal Reset to restore my normal text and background colors. What I want is for there to be no change at all when I use vi. The text should be black and the background grey. I have another server loaded with RedHat 9, and that acts normally; colors don’t change when using vi. Here is my .vimrc file: set compatible syntax off let g:loaded_matchparen=1 set nocp set noincsearch set nohlsearch set noshowmatch set bg=dark I've tried set bg=dark and set bg=light. It makes no difference. Is there some other set command that would clear this up for me, or some TERM setting (my TERM is set to linux)?

  Read the article

• Dim (NEARLY blank) laptop screen, secondary screen works - why?

  - by LIttle Ancient Forest Kami

  My laptop screen is (almost) black while my secondary screen is fine. I believe it to be backlight / brightness related. Problem description it starts when I start the laptop system loads and works fine, just screen has problems I can see the screen though very faintly / dimly - it's hard to see anything which ain't very white e.g. starting screen has big Thinkpad logo in white, large font - I can see it, though very dimly second screen works very well Official backligtht debugging: using acpi setting as prescribed there for Thinkpads didn't help I can see an entry in /sys/class/backlight/ and it changes when I press hotkeys for brightness (current backlight power for instance goes up or down) acpi-off didn't helpm neither did acpi_backlight=vendor Hardware data Laptop is Thinkpad Edge with glossy screen. 4 processors, 2 cores, exemplary CPU data from cat /proc/cpuinfo reports Genuine Intel i5 (M 480 @ 2.67GHz). OS is Ubuntu Lucid, 10.04 LTS, 64-bit, with Linux generic kernel (2.6.32-44) and GNOME 2.32.2 (though I doubt there lies the problem). $ lspci | grep VGA 01:00.0 VGA compatible controller: ATI Technologies Inc M92 [Mobility Radeon HD 4500 Series] $ lshw -C display *-display description: VGA compatible controller product: M92 [Mobility Radeon HD 4500 Series] vendor: ATI Technologies Inc physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:33 memory:c0000000-dfffffff(prefetchable) ioport:2000(size=256) memory:f0300000-f030ffff memory:f0320000-f033ffff(prefetchable) Driver I was NOT running any proprietary drivers, just checked with "Hardware drivers". There is one for ATI that is suggested there, though I didn't need it so far. UPDATE: changing the driver to proprietary one (ATI/AMD FGLRX) didn't help. Tried and failed Resetting / running on power or battery / charging / getting rid of static electricity / warming up *doesn't help* This is NOT a blank-screen problem, at least it isn't following official Ubuntu black-screen diagnostics - I can see my screen, though barely. What I will try next: - check last updates I've made - IIRC I am running on nomodeset already, but will verify this Any ideas how to proceed best? What is most probable cause?

  Read the article

< Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85  | Next Page >