Search Results

Search found 10098 results on 404 pages for 'per pixel'.

Page 79/404 | < Previous Page | 75 76 77 78 79 80 81 82 83 84 85 86  | Next Page >

  • Windows Server 2003 Terminal Server does not give out all available licenses

    - by Erwin Blonk
    I installed the Terminal Server role in Windows Server 2003 Standard 64-bits. Still, only 2 connections are allowed. The License Manager says that there are 10 Device CALs available, which is correct, and that none are given out. For good measure I let the server reboot, to no effect. Before this, there was another server (same Windows, except that it is 32 bits) active as a licensing server. I removed the role first and then then added it to the new server. I then removed the Terminal Server Licensing Server component off the old one and added it to the new one. After that, I added to licenses. When that didn't give the required result, I rebooted to new server. Still, the new server, with licenses and all, acts as if it has the 2 license RDP. The server are all stand-alone, there is no active directory been set up. Both servers are in different workgroups. Update (4/12/10): The server has changed the entries in the Terminal Server Licensing a few times. After installing the licenses it added an entry of which the exact phrasing I forgot but it was about temporary Windows 2003 device licenses. Later it added Windows Server 2003 - TS Per Device CAL. The temporary held 2 licenses (standard RDP licenses, I think) and the other 10. At some point, seemingly unrelated from the testing we did, it used a licenses from the new pool. This morning, 2 licenses were used from the pool of 10 and only 1 from the temporary/RDP pool (I wish I had screenshots to show, it changed every few hours oir so it seems). Although I had already activated the server over the internet, and re-activated it, I decided to go through the whole procedure by phone. Long story short, here is what it says now: Existing Windows 2000 Server, type:built-in [no licenses used, I add for for sake of being complete] Windows Server 2003 - Terminal Server Per Device CAL Token, type:open [none of 10 used] Windows Server 2003 - TS Per Device CAL, type:open [3 of 10 used] As I tried to explain, this is the end result after a few changes, most of which I can't directly connect to any action from my part. Only going to the activation procedure by phone seemed to directly effect the TS, resulting in the above configuration. Still, it is impossible to connect with more than 3 people, which is 1 up from the 2 that could connect yesterday. TS does say 7 licenses are avaible. Yet it won't give them out.

    Read the article

  • Enable VT-x in HP 8300 elite

    - by lang2
    I have a HP 8300 elite (Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz). I'm trying to run a virtual machine via VirtualBox. But every time I start the VM, it says: VT-x is disabled in the BIOS. (VERR_VMX_MSR_VMXON_DISABLED). My lscpu output is like this: Architecture: x86_64 CPU op-mode(s): 32-bit, 64-bit Byte Order: Little Endian CPU(s): 8 On-line CPU(s) list: 0-7 Thread(s) per core: 2 Core(s) per socket: 4 Socket(s): 1 NUMA node(s): 1 Vendor ID: GenuineIntel CPU family: 6 Model: 58 Stepping: 9 CPU MHz: 1600.000 BogoMIPS: 6784.74 Virtualization: VT-x L1d cache: 32K L1i cache: 32K L2 cache: 256K L3 cache: 8192K NUMA node0 CPU(s): 0-7 I went into the BIOS but the things the can be tweaked is very limited and I couldn't find the VT-x setting. Anybody know how to do this in this setup?

    Read the article

  • GET /wpad.dat entries flooding my access_log

    - by Aas
    I have a small LAN of some 30 users in it with proxy auto configuration enabled and working. Two of them are requesting wpad.dat file too rapidly at a pace of 30 times per second. 10.1.14.246 - - [02/Jun/2014:09:07:18 +0200] "GET /wpad.dat HTTP/1.1" 302 302 10.1.14.141 - - [02/Jun/2014:09:07:18 +0200] "GET /wpad.dat HTTP/1.1" 302 302 I don't know whether this is a problem from performance perspective, (the server is powerful enough to handle this) but the problem is it clogs up the access_log file. It grows about 1GB per week. Clients run Win7Pro. What could cause this behavior? What can be done to stop it? I have shortened log rotate window as a temporary workaround to prevent /var fill up. Thanks beforehand for your support.

    Read the article

  • many partitions on a single filegroup?¿ does it make sense?

    - by river0
    Hi, I'm designing a datawarehouse solution and I'm a newbie in disk configuration issues, let me explain you. Our storage is spread over 6 storage enlosures having each of them 5 raid-1 disk arrays, and having 2 LUNS defined per each disk array, which makes a total 48 LUNS (this is following Microsoft fast track recommendations for datawarehouse architectures). I would like to partition my data, on other projects I have worked before, we always followed a 1 partition - 1 filegroup rule. On the microsoft fast track recomendations it is advised to create a filegroup and then for that filegroup a data file per each lun... but I pretend to have a week level partitioning... if I apply that rule I think that I'll get too many files and a complex layout. I'm thinking of just creating just one filegroup (with the 48 lun data files), but still create the partitions since I want to keep soem of the benefits of partitions like partition switching... Is this scenario not recommended? What would you suggest?

    Read the article

  • Can Windows log CryptoAPI CRL timouts?

    - by makerofthings7
    We have several .NET applications that occasionally "act slow" with no CPU or disk access. I suspect that they are hung up on authentication when trying to validate the certificate, since the timeout is almost 20 seconds. As per this MSFT article Most applications do not specify to CryptoAPI to use a cumulative time-out. If the cumulative time-out option is not enabled, CryptoAPI uses the CryptoAPI default setting which is a time-out of 15 seconds per URL. If the cumulative time-out option specified by the application, then CryptoAPI will use a default setting of 20 seconds as the cumulative timeout. The first URL receives a maximum timeout of 10 seconds. Each subsequent URL timeout is half of the remaining balance in the cumulative timeout value. Since this is a service, how can I detect and log CryptoAPI hangs for applications I have sourcecode to, and also 3rd party

    Read the article

  • Can I speed up cygwin's fork?

    - by Andrew Aylett
    I came across a post discussing the speed of forking in Cygwin, giving an expected 'fork rate' in Windows XP of around 30-50 per-second (link) I've got a Core 2 duo (1.79GHz) which I would expect to get comparable results, but it's only managing around 8 forks per second (and sometimes a lot fewer): $ while (true); do date --utc; done | uniq -c 5 Wed Apr 21 12:38:10 UTC 2010 6 Wed Apr 21 12:38:11 UTC 2010 1 Wed Apr 21 12:38:12 UTC 2010 1 Wed Apr 21 12:38:13 UTC 2010 8 Wed Apr 21 12:38:14 UTC 2010 8 Wed Apr 21 12:38:15 UTC 2010 6 Wed Apr 21 12:38:16 UTC 2010 1 Wed Apr 21 12:38:18 UTC 2010 9 Wed Apr 21 12:38:19 UTC 2010 Can you suggest anything I might be able to do to speed things up? This machine acts a lot slower in Cygwin than others I've used before which actually were a lot slower.

    Read the article

  • Gauge network traffic for each Citrix session

    - by molecule
    Hi all, We are currently reviewing the bandwidth of our WAN links. How much bandwidth does a "typical" Citrix session utilize over a WAN link? JFYI - we are using Citrix Program Neighborhood V10 and each session is configured to use 256 colors. I have set up PRTG and it appears that for a server hosting 4 users, the traffic is approximately 100k to 300k per session. Is that about right? If you had to set a benchmark on a per-user basis, how much bandwidth would you assign to each user? Thanks in advance.

    Read the article

  • What does the "Max Memory Size" on the new Intel Core i3 / i5 / i7 CPU's mean?

    - by Josh
    I just noticed in the specs of the new Intel Core i-series processors that there is a "Max Memory Size" that is usually pretty small -- anywhere from 8GB to 24GB. See here: http://ark.intel.com/Product.aspx?id=41316 Core 2-based motherboards were just starting to roll out support for 32GB and greater memory sizes. Anyone have any idea what the Max Memory Size indicates? Is this the total limitation of the on-chip memory controller? Limitation per channel? Limitation per stick (e.g. density??)? Thinking of building a decent machine that needs lots of RAM, so I'm looking at the i7 860.

    Read the article

  • long access times and errors in iis application

    - by user55862
    I am having an issue with an IIS application (details of environment at the end of the message). The web site works great most of the time and I cannot reproduce any error in our test system. On the live system however with on averare of 5-15 requests per second I have a problem with that some requests (about 0.05%) will take over 300 seconds to complete. The other requests complete withing 5-10 seconds. It seem like if all the errornous requests end up with a Timer_EntityBody error in the error log. I have never seen this as an end user but I guess that they will receive some kind of error message. I am trying to find out what can be causing this errornous behaviour. Any ideas are welcome. I have read something about that there can be an MTU issue if ICMP and MTU protocols are blocked in the firewall. Does that sound reasonable? I have also read about updating to IIS 7 should do the trick. Does it sound reasonable? I think that the problem has another cause but I have no idea of what. I have tried running hte perormance monitor, monitoring for database locks and active transaction counts. I can see some of these in the perfmon log for the MSSQL server (another machine) for example: Active transactions is sometimes peaking and sometimes for long periods Lock waits per seconds is sometimes peaking Transactions per second is sometimes peaking Page IO Latch wait is sometimes peaking Lock wait time (ms) is sometimes peaking But I cannot see that any of these correlate to the errors in the IIS error log. On the IIS server machine I can also see with perfmon that some values peak a few times during a day: Request execution time Avg disk queue length I can neither see that any of these correlate to the errors in the IIS error log. In the below code I have anonymized by replacing some parts with HIDDEN The following can be seen in the access log 2010-10-01 08:35:05 W3SVC1301873091 **HIDDEN** POST /**HIDDEN**/Modules/BalanceModule.aspx - 80 - **HIDDEN** Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+5.1;+.NET+CLR+2.0.50727;+.NET+CLR+3.0.4506.2152;+.NET+CLR+3.5.30729;+.NET4.0C;+.NET4.0E) ASP.NET_SessionId=**HIDDEN** 400 0 64 0 2241 127799 At the same time the following can be seen in the error log: 2010-10-01 08:35:05 **HIDDEN** 1999 **HIDDEN** 80 HTTP/1.0 POST /**HIDDEN**/Modules/BalanceModule.aspx - 1301873091 Timer_EntityBody Test+Pool I can tell the following about the environment: Server: Windows Server 2003 x64 SP2 running on VMWare HTTP Server: IIS v6.0 with ASP.NET 2.0.50727 Antivirus: Trend Micro OfficeScan (Is it a good idea to have this on a server?)

    Read the article

  • Postgres 9.0 locking up, 100% CPU

    - by Jake
    We are having a problem where our Postgres 9.0 server occasionally locks up and kills our webapp. Restarting Postgres fixes the problem. Here's what I've been able to observe: First, usage of one CPU jumps to 100% for a few minutes Disk operations drop to ~0 during this time Database operations drop to 0 (blocks and tuples per sec) Logs show during this time: WARNING: worker took too long to start; cancelled WARNING: worker took too long to start; cancelled No Queries in logs (only those over 200ms are logged) No unusually long-running queries logged before or during Then the second CPU jumps to 100% The number of postgres processes jumps from the usual 8-10 to ~20 Matched by a spike in Postgres Blocks per second (about twice normal) Logs show LOG: could not accept SSL connection: EOF detected Queries are running but slow Restarting postgres returns everything to normal Setup: Server: Amazon EC2 Large Ubuntu 10.04.2 LTS Postgres 9.0.3 Dedicated DB server Does anyone have any idea what's causing this? Or any suggestions about what else I should be checking out?

    Read the article

  • MySQL is killing the server IO.

    - by OneOfOne
    I manage a fairly large/busy vBulletin forums (~2-3k requests per second, running on gigenet cloud), the database is ~ 10 GB (~9 milion posts, ~60 queries per second), lately MySQL have been grinding the disk like there's no tomorrow according to iotop and slowing the site. The last idea I can think of is using replication, but I'm not sure how much that would help and worried about database sync. I'm out of ideas, any tips on how to improve the situation would be highly appreciated. Specs : Debian Lenny 64bit ~12Ghz (6 cores) CPU, 7520gb RAM, 160gb disk. Kernel : 2.6.32-4-amd64 mysqld Ver 5.1.54-0.dotdeb.0 for debian-linux-gnu on x86_64 ((Debian)) Other software: vBulletin 3.8.4 memcached 1.2.2 PHP 5.3.5-0.dotdeb.0 (fpm-fcgi) (built: Jan 7 2011 00:07:27) lighttpd/1.4.28 (ssl) - a light and fast webserver PHP and vBulletin are configured to use memcached. MySQL Settings : [mysqld] key_buffer = 128M max_allowed_packet = 16M thread_cache_size = 8 myisam-recover = BACKUP max_connections = 1024 query_cache_limit = 2M query_cache_size = 128M expire_logs_days = 10 max_binlog_size = 100M key_buffer_size = 128M join_buffer_size = 8M tmp_table_size = 16M max_heap_table_size = 16M table_cache = 96

    Read the article

  • How to monitor current output/receive queue length in Linux

    - by IZhen
    I want to check the capacity and performance of my network. Besides checking the txkB/s and rxkB/s via Sar, I'd also like to see the average queue length of the network interface(so that the average queueing time in the interface can be calculated). It seems that netstat can give a per socket queue length, is it possible to get a per interface statics(a bit like Network Interface\Output Queue Length in Windows)? A related and kind of reverse questions is How do I view the TCP Send and Receive Queue sizes on Windows? Thanks

    Read the article

  • How can I re-encode H.264 video with minimal quality loss?

    - by SofaKng
    I have a lot of MPEG-TS files (.TS container but H.264 video) and playback is fine except that when you skip forward/backward or fast forward it's very sluggish and gets pixelated, etc. I've been trying to do research and I'm guessing that they were encoding with very few reference blocks (ie. it's a capture from a DVB-S satellite stream). When I re-encode them with Handbrake (.MP4 container) they play very, very good and seeking in the video is instant, etc, etc. Is it possible to transcode/re-encode my MPEG-TS files with minimal quality loss? If so, what is my best bet? They are each about 2 Mbps (ie. 2 GB per hour) but I don't want to re-encode them if "minimal quality loss" requires 10+ GB per file. I'm hoping to keep the video are the same size. Can anybody give me any advice?

    Read the article

  • Low framerate on background apps

    - by user1698923
    My problem is that when a game is running in the foreground, in Full Screen mode, any applications on my second monitor (such as youtube videos, videos, not app specific) drop their frame-rate to about 2-3 FPS. It seems like some sort of power management option that I can't track down. As far as I can tell, it's not due to the GPU not being able to keep up. For instance, my PC can play League of Legends at about 280FPS when the framerate is uncapped. If i cap it at 60FPS using the in-game option, it has no affect on the performance of the background app. Summary Operating System Windows 8 Pro 64-bit CPU Intel Core i7 3820 @ 3.60GHz 42 °C Sandy Bridge-E 32nm Technology RAM 12.0GB Triple-Channel DDR3 @ 533MHz (7-7-7-20) Motherboard Gigabyte Technology Co., Ltd. X79-UD3 (SOCKET 0) 37 °C Graphics DELL U2713HM (2560x1440@59Hz) DELL U2713HM (2560x1440@59Hz) 1280MB NVIDIA GeForce GTX 570 (Gigabyte) 58 °C Hard Drives 212GB Volume0 (RAID) 1863GB Western Digital WDC WD20EARS-00MVWB0 (SATA) 36 °C 1863GB Western Digital WDC WD20EARS-00MVWB0 (SATA) 34 °C Optical Drives No optical disk drives detected Audio ASUS Xonar Essence STX Audio Device Operating System Windows 8 Pro 64-bit Computer type: Desktop Graphics Monitor 1 Name DELL U2713HM on NVIDIA GeForce GTX 570 Current Resolution 2560x1440 pixels Work Resolution 2560x1400 pixels State Enabled, Output devices support Multiple displays Extended, Secondary, Enabled Monitor Width 2560 Monitor Height 1440 Monitor BPP 32 bits per pixel Monitor Frequency 59 Hz Device \\.\DISPLAY4\Monitor0 Monitor 2 Name DELL U2713HM on NVIDIA GeForce GTX 570 Current Resolution 2560x1440 pixels Work Resolution 2560x1400 pixels State Enabled, Output devices support Multiple displays Extended, Primary, Enabled Monitor Width 2560 Monitor Height 1440 Monitor BPP 32 bits per pixel Monitor Frequency 59 Hz Device \\.\DISPLAY5\Monitor0 NVIDIA GeForce GTX 570 Manufacturer NVIDIA Model GeForce GTX 570 GPU GF110 Device ID 10DE-1086 Revision A2 Subvendor Gigabyte (1458) Series GeForce GTX 500 Current Performance Level Level 3 Current GPU Clock 845 MHz Current Memory Clock 1900 MHz Current Shader Clock 1690 MHz Voltage 0.988 V Technology 40 nm Die Size 520 mm² Release Date Dec 07, 2010 DirectX Support 11.0 OpenGL Support 5.0 Bus Interface PCI Express x16 Temperature 57 °C Driver version 9.18.13.2018 BIOS Version 70.10.55.00.01 ROPs 40 Shaders 512 unified Memory Type GDDR5 Memory 1280 MB Bus Width 64x5 (320 bit) Filtering Modes 16x Anisotropic Noise Level Moderate Max Power Draw 219 Watts Count of performance levels : 3 Level 1 - "Default" GPU Clock 50 MHz Memory Clock 135 MHz Shader Clock 101 MHz Level 2 - "2D Desktop" GPU Clock 405 MHz Memory Clock 324 MHz Shader Clock 810 MHz Level 3 - "3D Applications" GPU Clock 845 MHz Memory Clock 1900 MHz Shader Clock 1690 MHz Things I've tried: 1) Updating the graphics driver 2) Setting windows power mode to High Performance 3) Reset Nvidia Global Performance settings to default

    Read the article

  • Postfix SMTP auth not working with virtual mailboxes + SASL + Courier userdb

    - by Greg K
    So I've read a variety of tutorials and how-to's and I'm struggling to make sense of how to get SMTP auth working with virtual mailboxes in Postfix. I used this Ubuntu tutorial to get set up. I'm using Courier-IMAP and POP3 for reading mail which seems to be working without issue. However, the credentials used to read a mailbox are not working for SMTP. I can see from /var/log/auth.log that PAM is being used, does this require a UNIX user account to work? As I'm using virtual mailboxes to avoid creating user accounts. li305-246 saslauthd[22856]: DEBUG: auth_pam: pam_authenticate failed: Authentication failure li305-246 saslauthd[22856]: do_auth : auth failure: [user=fred] [service=smtp] [realm=] [mech=pam] [reason=PAM auth error] /var/log/mail.log li305-246 postfix/smtpd[27091]: setting up TLS connection from mail-pb0-f43.google.com[209.85.160.43] li305-246 postfix/smtpd[27091]: Anonymous TLS connection established from mail-pb0-f43.google.com[209.85.160.43]: TLSv1 with cipher ECDHE-RSA-RC4-SHA (128/128 bits) li305-246 postfix/smtpd[27091]: warning: SASL authentication failure: Password verification failed li305-246 postfix/smtpd[27091]: warning: mail-pb0-f43.google.com[209.85.160.43]: SASL PLAIN authentication failed: authentication failure I've created accounts in userdb as per this tutorial. Does Postfix also use authuserdb? What debug information is needed to help diagnose my issue? main.cf: # TLS parameters smtpd_tls_cert_file = /etc/ssl/certs/smtpd.crt smtpd_tls_key_file = /etc/ssl/private/smtpd.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # SMTP parameters smtpd_sasl_local_domain = smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous broken_sasl_auth_clients = yes smtpd_recipient_restrictions = permit_sasl_authenticated,permit_mynetworks,reject_unauth_destination smtp_tls_security_level = may smtpd_tls_security_level = may smtpd_tls_auth_only = no smtp_tls_note_starttls_offer = yes smtpd_tls_CAfile = /etc/ssl/certs/cacert.pem smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_session_cache_timeout = 3600s tls_random_source = dev:/dev/urandom /etc/postfix/sasl/smtpd.conf pwcheck_method: saslauthd mech_list: plain login /etc/default/saslauthd START=yes PWDIR="/var/spool/postfix/var/run/saslauthd" PARAMS="-m ${PWDIR}" PIDFILE="${PWDIR}/saslauthd.pid" DESC="SASL Authentication Daemon" NAME="saslauthd" MECHANISMS="pam" MECH_OPTIONS="" THREADS=5 OPTIONS="-c -m /var/spool/postfix/var/run/saslauthd" /etc/courier/authdaemonrc authmodulelist="authuserdb" I've only modified one line in authdaemonrc and restarted the service as per this tutorial. I've added accounts to /etc/courier/userdb via userdb and userdbpw and run makeuserdb as per the tutorial. SOLVED Thanks to Jenny D for suggesting use of rimap to auth against localhost IMAP server (which reads userdb credentials). I updated /etc/default/saslauthd to start saslauthd correctly (this page was useful) MECHANISMS="rimap" MECH_OPTIONS="localhost" THREADS=0 OPTIONS="-c -m /var/spool/postfix/var/run/saslauthd -r" After doing this I got the following error in /var/log/auth.log: li305-246 saslauthd[28093]: auth_rimap: unexpected response to auth request: * BYE [ALERT] Fatal error: Account's mailbox directory is not owned by the correct uid or gid: li305-246 saslauthd[28093]: do_auth : auth failure: [user=fred] [service=smtp] [realm=] [mech=rimap] [reason=[ALERT] Unexpected response from remote authentication server] This blog post detailed a solution by setting IMAP_MAILBOX_SANITY_CHECK=0 in /etc/courier/imapd. Then restart your courier and saslauthd daemons for config changes to take effect. sudo /etc/init.d/courier-imap restart sudo /etc/init.d/courier-authdaemon restart sudo /etc/init.d/saslauthd restart Watch /var/log/auth.log while trying to send email. Hopefully you're good!

    Read the article

  • LUKS with LVM, mount is not persistent after reboot

    - by linxsaga
    I have created a Logical vol and used luks to encrypt it. But while rebooting the server. I get a error message (below), therefore I would have to enter the root pass and disable the /etc/fstab entry. So mount of the LUKS partition is not persistent during reboot using LUKS. I have this setup on RHEL6 and wondering what i could be missing. I want to the LV to get be mount on reboot. Later I would want to replace it with UUID instead of the device name. Error message on reboot: "Give root password for maintenance (or type Control-D to continue):" Here are the steps from the beginning: [root@rhel6 ~]# pvcreate /dev/sdb Physical volume "/dev/sdb" successfully created [root@rhel6 ~]# vgcreate vg01 /dev/sdb Volume group "vg01" successfully created [root@rhel6 ~]# lvcreate --size 500M -n lvol1 vg01 Logical volume "lvol1" created [root@rhel6 ~]# lvdisplay --- Logical volume --- LV Name /dev/vg01/lvol1 VG Name vg01 LV UUID nX9DDe-ctqG-XCgO-2wcx-ddy4-i91Y-rZ5u91 LV Write Access read/write LV Status available # open 0 LV Size 500.00 MiB Current LE 125 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 [root@rhel6 ~]# cryptsetup luksFormat /dev/vg01/lvol1 WARNING! ======== This will overwrite data on /dev/vg01/lvol1 irrevocably. Are you sure? (Type uppercase yes): YES Enter LUKS passphrase: Verify passphrase: [root@rhel6 ~]# mkdir /house [root@rhel6 ~]# cryptsetup luksOpen /dev/vg01/lvol1 house Enter passphrase for /dev/vg01/lvol1: [root@rhel6 ~]# mkfs.ext4 /dev/mapper/house mke2fs 1.41.12 (17-May-2010) Filesystem label= OS type: Linux Block size=1024 (log=0) Fragment size=1024 (log=0) Stride=0 blocks, Stripe width=0 blocks 127512 inodes, 509952 blocks 25497 blocks (5.00%) reserved for the super user First data block=1 Maximum filesystem blocks=67633152 63 block groups 8192 blocks per group, 8192 fragments per group 2024 inodes per group Superblock backups stored on blocks: 8193, 24577, 40961, 57345, 73729, 204801, 221185, 401409 Writing inode tables: done Creating journal (8192 blocks): done Writing superblocks and filesystem accounting information: done This filesystem will be automatically checked every 21 mounts or 180 days, whichever comes first. Use tune2fs -c or -i to override. [root@rhel6 ~]# mount -t ext4 /dev/mapper/house /house PS: HERE I have successfully mounted: [root@rhel6 ~]# ls /house/ lost+found [root@rhel6 ~]# vim /etc/fstab -> as follow /dev/mapper/house /house ext4 defaults 1 2 [root@rhel6 ~]# vim /etc/crypttab -> entry as follows house /dev/vg01/lvol1 password [root@rhel6 ~]# mount -o remount /house [root@rhel6 ~]# ls /house/ lost+found [root@rhel6 ~]# umount /house/ [root@rhel6 ~]# mount -a -> SUCCESSFUL AGAIN [root@rhel6 ~]# ls /house/ lost+found Please let me know if I am missing anything here. Thanks in advance.

    Read the article

  • How is the MTU is 65535 in UDP but ethernet does not allow frame size more than 1500 bytes

    - by nikku
    I am using a fast ethernet of 100 Mbps, whose frame size is less than 1500 bytes (1472 bytes for payload as per my textbook). In that, I was able to send and receive a UDP packet of message size 65507 bytes, which means the packet size was 65507 + 20 (IP Header) + 8 (UDP Header) = 65535. If the frame's payload size itself is maximum of 1472 bytes (as per my textbook), how can the packet size of IP be greater than that which here is 65535? I used sender code as char buffer[100000]; for (int i = 1; i < 100000; i++) { int len = send (socket_id, buffer, i); printf("%d\n", len); } Receiver code as while (len = recv (socket_id, buffer, 100000)) { printf("%d\n". len); } I observed that send returns -1 on i > 65507 and recv prints or receives a packet of maximum of length 65507.

    Read the article

  • Zabbix - Some of the monitored items don't refreh

    - by Niro
    I'm experiencing a strange issue with Zabbix monitoring a MySQL server. Most of the data from the server such as MySQL queries per second and MySQL uptime , Buffers memory etc. update nicely while some data like CPU iowait time (avg1) , Host local time ,MySQL number of threads and other items which were monitored in the past has last check time of about a week ago. I can't find any logic in this, for example Mysql number of threads and Mysql queries per second are obtained in a similar way so it does not make sense one of them is monitored and one is not. Please help- how can I fix this? Update - I used zabbix_get from the zabbix server to check one of the items on the zabbix client and it works so the problem must be on the zabbix server side

    Read the article

  • Using Amazon S3 for multiple remote data site uploads, securely

    - by Aitch
    I've been playing about with Amazon S3 a little for the first time and like what I see for various reasons relating to my potential use case. We have multiple (online) remote server boxes harvesting sensor data that is regularly uploaded every hour or so (rsync'ed) to a VPS server. The number of remote server boxes is growing regularly and forecast to keep growing (hundreds). The servers are geographically dispersed. The servers are also automatically built, therefore generic with standard tools and not bespoke per location. The data is many hundreds of files per day. I want to avoid a situation where I need to provision more VPS storage, or additional servers every time we hit the VPS capacity limit, after every N server deployments, whatever N might be. The remote servers can never be considered fully secure due to us not knowing what might happen to them when we are not looking. Our current solution is a bit naive and simply restricts inbound rsync only over ssh to known mac address directories and a known public key. There are plenty of holes to pick in this, I know. Let's say I write or use a script like s3cmd/s3sync to potentially push up the files. Would I need to manage hundreds of access keys and have each server customized to include this (do-able, but key management becomes nightmarish?) Could I restrict inbound connections somehow (eg by mac address), or just allow write-only to any client that was running the script? ( i could deal with a flood of data if someone got into a system? ) having a bucket per remote machine does not seem feasible due to bucket limits? I don't think I want to use a single common key as if one machine is breached then potentially, a malicious hack could get access to the filestore key and start deleting for ll clients, correct? I hope my inexperience has not blinded me to some other solution that might be suggested! I've read lots of examples of people using S3 for backup, but can't really find anything about this sort of data collection, unless my google terminology is wrong... I've written more than I should here, perhaps it can be summarised thus: In a perfect world I just want to have one of our techs install a new remote server into a location and it automagically starts sending files home with little or no intervention, and minimises risk? Pipedream or feasible? TIA, Aitch

    Read the article

  • Defragment an Exchange Volume

    - by IceMage
    The Scenario: I use a dedicated volume (RAID volume) to store all of my data for my Exchange 2007 server. Today, out of curiosity, I decided to check up on how fragmented the files on this data volume were. To my surprise, the answer is extremely. So, a three part question: First and Foremost, SHOULD I defragment this volume (after a full backup of course)? Be specific as to why not if I should not, or reasons I absolutely should if I should. Second, about how much time should I allow for during this maintenance period per gigabyte. The drives are all 7200 RPM SATA drives on a Hardware RAID 5 controller (Perc 5i/6i, can't remember), the files are extremely fragmented. (Over 5000 file fragments per gigabyte). Third, is there something wrong here? It seems to me like the drive shouldn't be this fragmented. Could something be configured incorrectly that could be causing this to happen?

    Read the article

  • BES 5.0 and MAPI calls to exchange system

    - by nysingh
    We have been using BES 4.1(5) for a while now and it has been a resource hog on exchange due to high number of MAPI calls. I have heard that BES 5.0 is even worse. the comparison i heard is that BES 4.1 is makes MAPI calls equal to 5 outlook clients per BB user and BES 5.0 makes MAPI calls equal to 10 outlook clients per BB user. can someone confirm if it is true? is BES 5.0 is really that bad in MAPI calls and for exchange performance. ? thanks

    Read the article

  • Terminal services and memory limits

    - by Mark Wassell
    Is there a way in Terminal Services to set limits on memory related parameters for a process. For example working set size and, possibly, if it makes sense, total virtual memory allocation for the session? To turn the question around, we have an application which cannot allocate as much virtual memory running on a terminal server as it can when running on a desktop PC (both I would expect to have a limit of 2GB for user mode address space) and I was wondering if there is another limit for processes or users on a terminal server. Perhaps even 2GB per user rather than per process.

    Read the article

  • amazon ec2 pricing

    - by Pradyut Bhattacharya
    I m really confused. I was trying to buy hosting at amazon ec2. My site will not be having much of a traffic and i will be installing glassfish and mysql. Usage will be 1gb of ram and around less than 5gb of hardisk and same bandwidth. As mine is a startup, the number of hits per day would be less than 20hits per day, each hit having around 10mins time. How should i calculate the price on the ec2 calculator. Thanks

    Read the article

  • Online backup solution

    - by Petah
    I am looking for a backup solution to backup all my data (about 3-4TB). I have look at many services out there, such as: http://www.backblaze.com/ http://www.crashplan.com/ Those services look very good, and a reasonable price. But I am worried about them because of incidents like this: http://jeffreydonenfeld.com/blog/2011/12/crashplan-online-backup-lost-my-entire-backup-archive/ I am wondering if there is any online back solution that offers a service level agreement (SLA) with compensation for data loss at a reasonable price (under $30 per month). Or is there a good solution that offers a high enough level of redundancy to mitigate the risk? Required: Offsite backup to prevent data loss in terms of fire/theft. Redundancy to protect the backup from corruption. A reasonable cost (< $30 per month). A SLA in case the service provider faults on its agreements.

    Read the article

  • How can I rip a DVD but merge/join episodes

    - by Nifle
    Some background. I have the Pink Panther Collection, they have about 30 episodes on each DVD. Now I want to watch this on my $MobileDevice. So I went and converted it to m4v or avi. This of course went splendid with both Handbrake and AutoGK but the problem is that I want ONE file per DVD, both Handbrake and AutoGK creates one file per episode. So here finally is my question. Does anyone know how to persuade Handbrake or AutoGK to create one video file with all the episodes? Or can anyone recommend another (free/cheep) tool for the job? Oh and no cheating by telling me to join the files after conversion. I have never found a video joiner that did not disappoint me (usually bad audio sync).

    Read the article

< Previous Page | 75 76 77 78 79 80 81 82 83 84 85 86  | Next Page >