Search Results

Search found 4224 results on 169 pages for 'wireless n'.

Page 79/169 | < Previous Page | 75 76 77 78 79 80 81 82 83 84 85 86  | Next Page >

• HP Officejet 4500 G510n-z Not Showing up in Remote Desktop (Terminal Services)

  - by Greg_the_Ant

  I installed this printer on a windows XP machine. First using the wireless option, and later using USB. In both cases when I connect to my other computer (also Windows XP) via terminal services and check printers in the local resources tab it does not show up on the remote session. I used to have a Samsung connected to my local computer over USB and and that worked fine over terminal services. Things I tried so far: I did read this page and installed the software fix on both computers: (Printers that use ports that do not begin with...) I installed the minimum HP software install on the remote computer and that didn't help either. I also tried running the add new printer wizard on the remote computer: I selected "local printer attached to this computer" and did not check the "automatically.." option. On the next page of the wizard I can select an option for "use the following port". I see options for TS001 through TS009 there. I'm assuming those are coming from the local machine. I tried clicking each one and then checking "have disk" and pointing it to C:\3be8dc611b11322e8ddf8a67\i386\msxpsdrv.inf 1 but for every single TS00.. port it says "The specified location does not contain information about your hardware." Any help would be greatly appreciated. I'm pretty stuck at this point. 1 C:\3be8dc611b11322e8ddf8a67 is the folder I extracted the HP driver software to after I downloaded it.

  Read the article

• Linksys router cannot change default password

  - by Jessica M.

  My wireless internet suddenly stopped working today. I have Windows 7 and Lindsys WRT54G router. I tried to log into the Linksys setup router page by typing in www.192.168.1.1 into firefox and it prompted me for a username and password as usual. The problem is when i tried to enter my regular username and password it did not work. I finally solved my problem when I came across this post here and the very last post solved my problem. It suggested I try username: root / password: admin. For some reason the username and password has been changed. When i tried username: root / password: admin , it worked and allowed me to get into the Linksys setup page. The problem is I can't change the username or password anymore. Every time I want to log into my Linksys setup page I have to enter username: root / password: admin. I can't change the "WPA shared key" (password). For the security settings I selected WPA2Personal + AES. Also the post said "If the firmware was upgraded to non-linksys firmware - the default will be different" . The problem is I didn't update anything and I'm worried that someone installed a virus or something or somehow changed the firmware on my router. How did I get non-Linksys firmware on my router? EDIT: I figured out how to change the password when I log into the Lynksys setup page. Administration -- Management -- password. I still don't understand if my router firmware was changed or who changed it or if it happened by mistake.

  Read the article

• Port Forwarding(?) TD-W8961nd

  - by rich

  I have a bit of a weird internet setup. I am connected via a decent WiFi connection (from work) which I pick up using a Buffalo Airstation Wireless-G box. This simply picks up the signal and gives me 4 ethernet ports to connect to. That's all fine and works as it should. I also have a TP LINK TD-W8961nd router which used to be connected to the Airstation via an ethernet cable so I could essentially have WiFi access in my house. To cut a long story short I can't remember how the hell I got it to work and I can't find the notes I scribbled down on how to do it. I'm pretty sure I need to tell the router what ip to pick up the internet connection from and have the local wifi as a seperate network. How the hell I do that I have no idea right now. Can anyone give me some advice on this? If you need more information ask and I will be able to do so. Cheers in advance. edit I'm in work at the moment so I can't give 100% details but I will be able to later on.

  Read the article

• Ways to have audio output without wires

  - by viraptor

  I'm trying to find a way of using my home speakers/amp without actually having to connect them. There are two laptops that use them normally (so I don't like changing the connection all the time) and I'd rather move the speakers to a place that's away from the couch. I'm not sure how to do this though... The options I can think of are: some kind of wireless jack-jack connection finally getting a media server Unfortunately I can't find any good product for the first solution. I've seen some headphones which have the receiver integrated and a separate transmitted, so in general the idea is already out there, just not the way I need ;) I've seen also http://www.miccus.com/products/blubridge-mini-jack, but I'd have to have a compatible receiver which I can't find on its own (maybe there's some application that the media server could use?). As far as media server goes... many of the plug servers look really interesting, but I'm not sure how to create an audio output and how to redirect the input really. None of the plug servers I've seen so far advertises the option of audio output jack port. I think this part could be fixed by getting one with an usb port and a separate cheap usb soundcard. I hope that input can be sorted out in some rather simple way. I've got Linux running on both laptops so I hope that would be possible to configure jack/pulse/whatever to use the remote endpoint, or even write a simple local-/dev/dsp:network:media-server-/dev/dsp forwarder. So the main question is... are there better ways? Are there any out of the box solutions? Or maybe this was already done by someone and described somewhere?

  Read the article

• Wiring my internet

  - by u8sand

  I have Verizon internet service and am currently using wifi. My router is in the basement and my desktop computer is 2 floors and on the other side of the house above it... Worst possible positioning but that's just how things worked out. My wireless currently is extremely unstable so I've decide to correct the problem by wiring my computer directly. The problem lies here: when redoing the room next to it (when the wall was open) we went ahead and wired some coaxial cable from our attic to our basement (with plenty of slack on both ends, don't ask me why we didn't go ahead and wire a CAT6 cable). The question is: Can I use the coaxial cable to bring me internet connection? Naturally the router (which needs to stay where it is) takes a coaxial cable input and has Ethernet outputs. So maybe I would have to take a ethernet cable, convert to coaxial-coaxial to my computer, convert back to ethernet. Is this even possible to convert from coaxial to ethernet? Or do I have to attempt to go ahead and fish a cat6 cable through my house. I cannot just split the signal because that would require two routers and two networks (which I don't believe would work with one cable-one ISP correct me if I'm wrong). Thanks

  Read the article

• Arch Linux drops me on my school network

  - by Kravlin

  I'm running a Lenovo X61 which i carry around my college for getting on the internet at various points in the day. The network has always been finicky but recently it's gotten worse. I'll connect using iwconfig, get an ip from dhcpcd and log in using vpnc to their system. Sometimes I'll stay connected for hours but most of the time within 30 seconds my network traffic will drop to zero and i'll be unable to do anything. My computer still belives it's connected, however to try again i need to put my wireless interface down, put it back up and try again. It's gotten so bad that i've got a window on my computer pinging yahoo or google constantly in order to know if i'm still able to get online. I know other people who have used Arch Linux that don't have the same problems as well as people who use Ubuntu who haven't had any problems either. It seems like my computer is a special case. Does anyone have any suggestions on how to fix it? dmesg doesn't show anything out of the ordinary going on and i don't know where else to look for errors or other things to try. Edit: this doesn't happen on my home network. It's a problem that only happens at school.

  Read the article

• PEAP validating a secondary domain suffix

  - by sam

  Probably the title is a little bit confusing, let me explain the situation. Our company wants to implement a corporate wireless lan with PEAP authentication. unfortunately someone made a big mistake in our AD design 10 years ago. The domain name we are using "company.ch" is not owned by company but by someone else. so it is not possible to issue a public SSL certificate for the RADIUS server. Our AD is to big to rename it. We already thought about using our private PKI and rollout the CA certificate via GPO but that would only cover our corporate managed clients but not the BYOD (Smartphones, Tablets, Laptops..) Is there a way to add a secondary domain name like “company2.ch” and issue a public certificate and join that radius to that secondary domain aslwell, and configure that secondary dns suffix via DHCP for all the client pools... or is there another way with for example a new radius server which has his own domain company2.ch which is connected with some kind of trust between the company.ch doamin? sorry i'am not a client server guy.. hopefully you get my drift.!?

  Read the article

• What kernel modules are required for wi-fi to work?

  - by Leonid Shevtsov

  My custom-built 2.6.32 kernel cannot connect to any WPA-protected network. The kernel includes (probably?) everything that should be needed for wifi, including IPv4 network support (IPv6 is disabled), the ath5k wireless driver (which is used in the generic Ubuntu 2.6.31 kernel) and all crypto APIs. The card is being detected, however, iwlist scan returns wlan0 Failed to read scan data : Network is down and network-manager log says <info> (wlan0): driver supports SSID scans (scan_capa 0x01). <info> (wlan0): new 802.11 WiFi device (driver: 'ath5k') <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/1 <info> (wlan0): now managed <info> (wlan0): device state change: 1 -> 2 (reason 2) <info> (wlan0): bringing up device. <info> (wlan0): preparing device. <info> (wlan0): deactivating device (reason: 2). supplicant_interface_acquire: assertion `mgr_state == NM_SUPPLICANT_MANAGER_STATE_IDLE' failed <info> modem-manager is now available <WARN> default_adapter_cb(): bluez error getting default adapter: The name org.bluez was not provided by any .service files <info> Trying to start the supplicant... <info> (wlan0): supplicant manager state: down -> idle <info> (wlan0): device state change: 2 -> 3 (reason 0) <WARN> nm_supplicant_interface_add_cb(): Unexpected supplicant error getting interface: wpa_supplicant couldn't grab this interface. The exact same configuration works with the generic kernel. Is anything except wifi and crypto api needed for wi-fi to work?

  Read the article

• What is the peak theoretical WiFi G user density? [closed]

  - by Bigbio2002

  I've seen a few WiFi capacity planning questions, and this one is related, but hopefully different enough not to be closed. Also, this is related specifically to 802.11g, but a similar question could be made for N. In order to squeeze more WiFi users into a space, the transmit power on the APs need to be reduced and the APs squeezed closer together. My question is, how far can you practically take this before the network becomes unusable? There will come a point where the transmit power is so weak that nobody will actually be able to pick up a connection, or be constantly roaming to/from APs spaced a few feet apart as they walk around. There are also only 3 available channels to use as well, which is a factor to consider. After determining the peak AP density, then multiply by users-per-AP, which should be easier to find out. After factoring all of this in and running some back-of-the-envelope calculations, I'd like to be able to get a figure of "XX users per 10ft^2" or something. This can be considered the physical limit of WiFi, and will keep people from asking about getting 3,000 people in a ballroom conference on WiFi. Can anyone with WiFi experience chime in, or better yet, provide some calculations for a more accurate figure? Assumptions: Let's assume an ideal environment with no reflection (think of a big, square, open room, with the APs spaced out on a plane), APs are placed on the ceiling so humans won't absorb the waves, and the only interference are from the APs themselves and the devices. As for what devices specifically, that's irrelevant for the first point of the question (AP density, so only channel and transmit power should matter). User experience: Wikipedia states that Wireless G has about 22Mbps maximum effective throughput, or about 2.75MB/s. For the purpose of this question, anything below 100KB/s per user can be deemed to be a poor user experience. As for roaming, I'll assume the user is standing in the same place, so hopefully that will be a non-issue.

  Read the article

• How is it possible that I can do a host lookup but not a curl?

  - by Daniel Quinn

  Has anyone ever seen this before? Note that this happens not only with google.com, but with every domain I try. It's a wireless connection (WEP), but I'm not sure how that would be relevant: $ curl -v google.com # This takes about 60s to return * getaddrinfo(3) failed for google.com:80 * Couldn't resolve host 'google.com' * Closing connection #0 curl: (6) Couldn't resolve host 'google.com' $ host google.com google.com has address 209.85.148.106 google.com has address 209.85.148.147 google.com has address 209.85.148.99 google.com has address 209.85.148.103 google.com has address 209.85.148.104 google.com has address 209.85.148.105 google.com mail is handled by 30 alt2.aspmx.l.google.com. google.com mail is handled by 40 alt3.aspmx.l.google.com. google.com mail is handled by 50 alt4.aspmx.l.google.com. google.com mail is handled by 10 aspmx.l.google.com. google.com mail is handled by 20 alt1.aspmx.l.google.com. $ cat /etc/resolv.conf # Generated by NetworkManager nameserver 192.168.1.201 $ cat /etc/hosts 127.0.0.1 localhost ::1 localhost $ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.1.254 0.0.0.0 UG 0 0 0 wlan0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0

  Read the article

• How can I print from my lion mac mini to my windows XP, with simple file sharing?

  - by Jules

  I have quite a complicated setup, perhaps. And a lot of history on this issue, I'm hoping that I don't have to buy a new printer. I've got a HP Wireless USB Print Server, which requires client software, I can't just use it as an IP Printer. The HP software is pretty poor on the mac and is no longer supported and often locks up the printer server and takes some considerable effort to actually print something. Let alone if a windows machine attaches to it first. My printer is an Epson Stylus R285. However, the windows client software is fine and we can print from windows 7 / XP without problem. We have simple file sharing setup as this is the only way I could get windows XP to talk to windows 7. However, I can't seem to get my mac mini to connect as anything other than a guest to my xp machine, to connect to the shared printer. I'm not considering some kind of internet printing as this would seems the simplest solution. But I'm not sure what will work with my setup ?

  Read the article

• Create a wifi hotspot in a place where an authentication is required

  - by SoftTimur

  I live in a residence where Internet is provided via cable. Once the computer is connected to the cable, launching a browser will trigger an authentication, I have a username and password to enter, then the internet will be connected. With a gateway (e.g. Wireless Cable Voice Gateway Model CBVG834G) and 2 cables, two PCs can connect to the Internet with my account at the same time. Now the question is, I don't like the cable, and would like to create a wifi hotspot. It seems realizable with the same gateway. According to the instruction on page 2-4 of the manual: Enter http://192.168.0.1 in the address field of your Internet browser. Log in to the gateway with either of the default user names, MSO or admin... However, while connecting to the Internet successfully via cable and the gateway (e.g. google works), opening 192.168.0.1 oddly gives me an error on the browser: Does anyone know what happened? Is it due to the authentication required by my residence? Is there any other way to build a hotspot of wifi? PS: My system is MAC OS

  Read the article

• Monitor mode 802.11 captures on OSX

  - by Mike A

  I'm trying to determine the difference between capturing 802.11 frames in the following ways on OSX (10.8.5). It's a bit esoteric, but I use "Option 2" to capture frames for later analysis, and am wondering if I'm missing something. Option 1: use "airportd": $sudo /usr/libexec/airportd en0 sniff Option 2: use "airport" followed by tcpdump: sudo /System/Library/PrivateFrameworks/Apple80211.framework/Versions/Current/Resources/airport --channel= sudo tcpdump -I -P -i en0 -w /tmp/capture.pcap (or alternatvely eliminate the -w and watch packets real-time). From what I can tell: Both commands, according to the wifi icon on OSX, put the interface into 'monitor' mode. Both commands output a pcap file that is readable in both wireshark/tcpdump & Eye PA. Both commands appear to capture management, control and data frames. The rub: Option 1 disconnects you from the network. This is expected, when putting an interface into 'monitor' mode. Option 2 does NOT disconnect you, provided you've set the channel to the same channel your currently connected to. This has a distinct advantage of keeping your connection up while capturing in monitor mode. My question: Option 2 does not seem like it should work, or more specifically, it does not seem like I should be able to remain connected while also capturing frames in monitor mode. On a wired NIC, you can be 'promiscuous' and still send frames, though I didn't think the same was true for wireless NIC. I'm questioning the validity of capturing frames w/ Option 2?

  Read the article

• Netgear router keeps disconnecting iPhone

  - by DisgruntledGoat

  My old router (Voyager 2091) packed up so I just got a new router - a Netgear N150 model DGN1000. My laptop connects OK wirelessly, but my iPhone 4S is constantly getting "disconnected" - it has perfect wifi signal and is seemingly connected to the router, but no pages load (it says "server cannot be found"). If I disconnect manually ("forget this network") then reconnect, it works fine again for a random amount of time (usually 10-30 minutes) then I get the same problem again. I've done some searching and this appears to be a known problem - there are dozens of forum posts out there lamenting similar connection problems. The only advice I have seen is to set a specific channel under Wireless Settings on the router CP, although every forum post recommends a different channel! 1, 3, 5, 6, 11... I have tried them all for hours at a time and get the exact same problem. The firmware is up to date. Is there an actual solution for this, or do I need to get a different router just to be able to use my iPhone?

  Read the article

• VLAN for WiFi traffic separation (new to VLANing)

  - by Philip

  I run a school network with switches in different departments. All is routed through to a central switch to access the servers. I would like to install WiFi access points in the different departments and have this routed through the firewall (an Untangle box that can captive-portal the traffic, to provide authentication) before it gets onto the LAN or to the Internet. I know that the ports that the APs connect to on the relevant switches need to be set to a different VLAN. My question is how do I configure these ports. Which are tagged? Which are untagged? I obviously don't want to interrupt normal network traffic. Am I correct in saying: The majority of the ports should be UNTAGGED VLAN 1? Those that have WiFi APs attached should be UNTAGGED VLAN 2 (only) The uplinks to the central switch should be TAGGED VLAN 1 and TAGGED VLAN 2 The central switch's incoming ports from the outlying switches should also be TAGGED VLAN 1 and TAGGED VLAN 2 There will be two links to the firewall (each on its own NIC), one UNTAGGED VLAN 1 (for normal internet access traffic) and one UNTAGGED VLAN 2 (for captive portal authentication). This does mean that all wireless traffic will be routed over a single NIC which will also up the workload for the firewall. At this stage, I'm not concerned about that load.

  Read the article

• Asus PCE-N53 11n N600 PCI-E Adapter on 3.x kernel

  - by CITguy

  Problem ASUS PCE-N53 wireless NIC doesn't work for latest versions of the linux kernel. How do I get it working on my system? (Note: I'm posting the answer I've found for others to use.) Installing Driver for Linux 3.x Kernel ASUS provides Linux drivers from their website, but it mentions that the driver supports "Linux Kernel 2.6.x", so it won't work without a some modifications to the driver code. Fortunately, an archlinux forum mentions similar problems and one user was able to create a patch for kernel 3.8.x that seems to work with kernel 3.11.x. Here's how I got it working: Prerequisites Ubuntu: sudo apt-get install build-essential Arch: sudo pacman -S base-devel Steps: 1. Download the driver from the ASUS website The download can be found under "Support Drivers & Tools". 2. Unzip the contents of the downloaded file cd into the new directory 3. Patch The arch forum mentions a 3.8 patch file that needs to be downloaded. Download rt5592sta_fix_64bit_3.8.patch to the current directory. tar -xvf {driver_source.tar.gz} cd into the directory created in previous step patch -p1 < ../rt5592sta_fix_64bit_3.8.patch 4. Compile NOTE: You will need to use sudo for it to compile properly. sudo make sudo make install sudo modprobe rt5592sta 5. Enjoy If all is well, you should now have a working card.

  Read the article

• Encrypted WiFi with no password?

  - by Ian Boyd

  Is there any standard that allows a WiFi connection to be encrypted, but not require a password? i know that (old, weak) WEP, and newer WPA/WPA2 require a password (i.e. shared secret). Meanwhile my own wireless connections are "open", and therefore unencrypted. There is no technical reason why i can't have an encrypted link that doesn't require the user to enter any password. Such technology exists today (see public key encryption and HTTPS). But does such a standard exist for WiFi? Note: i only want to protect communications, not limit internet access. i get the sense that no such standard exists (since i'm pretty capable with Google), but i'd like it confirmed. Claraification: i want to protect communcations, not limit internet access. That means users are not required to have a password (or its moral equivalent). This means users are not required: to know a password to know a passphrase to enter a CAPTCHA to draw a secret to have a key fob to know a PIN to use a pre-shared key have a pre-shared file to possess a certificate In other words: it has the same accessibility as before, but is now encrypted.

  Read the article

• How do I determine how future-proof and stable a router is?

  - by Aarthi

  I mentioned in my last question that my wireless router had a bad habit of crashing. After consulting with the Super User chatroom, as well as my sysadmin, I've decided I may as well purchase a new router. However, I'm unsure how to evaluate all these tech specs that get touted about. The two things that seem to be the most important to me are: (1) keeping my router future-proof (as standards evolve and change), and (2) ensuring its stability. Unfortunately, I'm not sure what, exactly, I should be looking for in the tech specs or the item description that can give me a good idea of how stable or future-proof my decide will be. What should I look for? Can I determine stability without having to try the device out myself? Please note: I'm not a battle-hardened power user by any means, so I'll likely be reliant on the given firmware for my router. My last router lasted me like four years, so I mostly just want something that'll cover a 500 sqft apartment in New York with minimal crashing, so that I can watch Hulu in peace. And make Skype calls. If it helps, the router models that I'm currently decided between are this ASUS one and this LinkSys one.

  Read the article

• How to host an ssh server?

  - by balki

  Hi, I have a broadband internet connection. I have an wireless modem (Airtel India). I don't have a static ip address. I want to host a ssh/web/ftp server to be visible to the outside world just for testing and learning purpose so I can ask my friend to connect to my current ip address and test. My modem has an admin interface which allows to port forward and open ports. I set up ssh server as shown and checked if port 22 is open using this website , Port Scan And port 22 is open. I have an openssh server running and it works if i do, ssh [email protected] which is my local ip address but doesn't work if i do ssh [email protected] where 122.xx.xx.xx is my external ip address of my modem which i checked from whatismyipaddress.com. Since it looks like the port is open, I wonder if there is some setting I need to change in my server config to expose my server. How should I go about solving this?

  Read the article

• How to setup firewall to allow internet connection sharing via Wifi USB stick?

  - by hannanaha

  I have a Windows8 computer linked to the internet via an ethernet cable ("Ethernet" network connection). I have attached to it a DLink Wifi USB stick, and I'm trying to share the main PC's internet connection with my Android phone via a local wifi network. I am using the following batch file to set up this network: netsh wlan set hostednetwork mode=allow ssid=MyWifiName key=password keyUsage=persistent netsh wlan start hostednetwork After I run this script, I can see a new network connection appear in "Control Panel\Network and Internet\Network Connections" named "Local Area Connection *12", and I can see "MyWifiName" on the Android phone. The device name for this connection on the PC is "Microsoft Hosted Network Virtual Adapter". I also set up the "Ethernet" connection to share Internet with "Local Area Connection *12". However, the Android phone usually doesn't manage to obtain an IP from the wireless network, and when it does, there still seems to be no connectivity to the internet. When I turn off the Windows Firewall completely, or even just for "Local Area Connection *12", the Android connection is perfect. My questions are: How should I set up the Windows firewall to allow the phone to connect properly? Is there a specific rule I need to add to the Windows firewall advanced settings? [Note: the above method worked great in Windows 7, without any specific tinkering with the firewall]. Is it safe to turn off the firewall specifically for the "Local Area Connection *12" (the wifi connection) if the main Ethernet connection is still protected by the firewall? Thanks in advance.

  Read the article

• port forwarding/network settings preventing from game hosting

  - by Xitcod13

  I asked where to post this question on stackoverflow meta and they directed me here. Im on wireless connection and I want to host games in StarCraft: Brood War and i've been looking everywhere on how to accomplish that. My internet is amazingly fast so its not an internet problem (and when i play other peoples games dont experience lag) I found out that i need to have a static IP but I have already checked that i do (i downloaded a program to make my id static and it already was; The program asked for which router I used So i think it checked the router settings already) I found out that i need to allow Sc access through the firewall which i already did (i have zone-alarm but I allowed it everything possible except receiving emails lol) I have recently noticed that few people actually can join my games but most of them cannot. I dont know whats going on here. I really want to be able to host games overall how do I go about checking what is wrong with the network. Update: Alright I figured out what i did wrong in the first part I did not actually set up forwarding on the router -.- I have tried to fix my mistake. I went to forwarding options in my router (as this guide for my specific router suggests) but when i click ok I get a message incorrect ip address. 192.168.1.1 is my routers address. The default address that appears there is 192.168.1 (blank) I have set it to my computers current Ip4 adress which 192.168.1.23 I hope this works If so i will post it as an answer and mark it.

  Read the article

• Why does my microwave kill the Wi-Fi?

  - by Ohlin

  Every time I start the microwave in the kitchen, our home Wi-Fi stops working and all devices lose connection with our router! The kitchen and the Wi-Fi router are in opposite ends of the apartment but devices are being used a little here and there. We've been annoyed by the instability of the Wi-Fi for some time and it wasn't until recently we realized it was correlated to microwave usage. After some testing with having the microwave on and off we could narrow down the problem to only occurring when the router is in b/g/n mode and uses a set channel. If I change to b/g mode or set channel to auto then there is no problem any more...but still! The router is a Zyxel P-661HNU ("802.11n Wireless ADSL2+ 4-port Security Gateway" with latest firmware) and the microwave is made by Neff with an effect of 1000W (if this information might be useful to anyone). There is an "internet connection" light on the router and it doesn't go out when the interruption occurs so I think this is only an internal Wi-Fi issue. Now to my questions: What parts of the Wi-Fi can possibly be affected by the microwave usage? Frequency? Disturbances in the electrical system? How can setting Auto on channels make a difference? I thought the different channels were just some kind of separation system within the same frequency spectrum? Could this be a sign that the microwave is malfunctioning and slowly roasting us all at home? Is there any need to be worried? Since we were able to find router settings that cooperate well with our microwave's demand for attention, this question is mainly out of curiosity. But as most people out there...I just can't help the fact that I need to know how it's possible :-)

  Read the article

• Games consoles won't connect through the TP-Link TL-WA500G Access Point

  - by Manfred Wolff

  I hope that someone can help me. I have several Laptops and other devices, all using my Wireless Router (Sky Digital Netgear) To extend the range to the back of the house, I purchased a TP-Link TL-WA500G Range extender. configured just as a pure repeater, it picks up the signal from the Netgear Router. The Netgear Router does the DHCP, handing out the IP addresses. This all works a treat with several different laptops and my iPone4S, but when my son tries to use his XBox360, Sony Playstation3 or the Nintendo Wii those devices fail to acquire an IP address. They just sit their waiting for the IP config. This also happens with my wife's HTC desire ONE Android phone. My son says that, when his HTC Desire C won't get an IP address, he just unplugs the AP briefly - the phone will connect and he puts the AP back on. Once he is connected to the Router, the AP won't disturb function. The Games Consoles don't seem to work like that. They stop working, when the AP is reconnected. I had my son try to configure permanent IP addresses, and he said that did not work either, though I have to confirm that, as I did not see that for myself. Has anybody seen this before? I have searched the Net and have not found any similar problems anywhere. I wonder if there is setting somewhere that would fix this. Many thanks for anyone reading this and trying to help. M

  Read the article

• Network topology for both direct and routed traffic between two nodes

  - by IndigoFire

  Despite it's small size, this is the most difficult network design problem I've faced. There are three nodes in this network: PC running Windows XP with an internal WiFi adapter.Base station with both WiFi and a Wireless Modem (WiModem)Mobile device with both WiFi and WiModem The modem is a low-bandwidth but high-reliability connection. We'd like to use WiFi for high-bandwidth stuff like file transfers when the mobile is nearby, and the modem for control information. Here's the tricky part: we'd like the wifi traffic to go directly from the mobile to the PC, as rebroadcasting packets on the same WiFi channel takes up double the bandwidth. We can do that with a manual configuration by giving the both the PC and the base station two IP addresses for their WiFi interfaces: one on a subnet shared with the mobile, and one on their own subnet. The routes on the PC are set up so that any traffic going to the mobile via WiModem goes through the secondary IP address so that return traffic from the mobile also goes through the WiModem. Here's what that looks like: PC WiFi 1: 192.168.2.10/24 WiFi 2: 192.168.3.10/24 Default route: 192.168.2.1 Base Station WiFi 1: 192.168.2.1/24 WiFi 2: 192.168.3.1/24 WiModem: 192.168.4.1/24 Mobile WiFi: 192.168.3.20/24 WiModem: 192.168.4.20/24 We'd like to move to having the base station automatically configure the mobile and PC, as the manual setup is problematic when you start having multiple mobiles and PCs. This means that the PC can only have 1 IP address and needs to be treated as being pretty simple. Is it possible to have a setup driven by DHCP on the base station that is efficient with bandwidth?

  Read the article

• How to troubleshoot Linksys E4200 Remote Management

  - by Jordan

  My Linksys E4200 is configured for Remote Management, but the router is not accepting the connections. Here's the configuration under Administration Management Remote Management Access: Remote Management: Enabled Access via: HTTP Remote Upgrade: Disabled Allowed Remote IP Address: Any IP Address Remote Management Port: 8080 The router is setup to use 192.168.10.41 as its static Internet IP address, and 192.168.35.1 as its LAN IP address. I can access the router just fine via its LAN IP address, but I can't make a connection using http://192.168.10.41:8080. I've tried variations of the settings above (enabled HTTPS, enabled Remote Upgrade, set an IP range of 192.168.10.1-254) but nothing has worked yet. Hoping someone can at least point me in the right direction. Thanks. Update: To clarify, I have a wired router that connects straight to the T1 modem. It's configured to use 192.168.10.1-254 as its internal LAN range. The E4200 wireless router in question is on that LAN using 192.168.10.41 as its WAN IP address. The E4200's internal LAN range is 192.168.35.1-254. I'm not trying to access the E4200 from the Internet, I'm just trying to access it from its WAN IP address. Thanks.

  Read the article

< Previous Page | 75 76 77 78 79 80 81 82 83 84 85 86  | Next Page >