Search Results

Search found 4224 results on 169 pages for 'wireless n'.

Page 86/169 | < Previous Page | 82 83 84 85 86 87 88 89 90 91 92 93  | Next Page >

  • router only assigns small number of IPs

    - by Liam Coates
    Been having a problem with my router for a while now, might just be because it is really old but here's the problem: If a lot of computers are connected to my home network someone will get disconnected. They are assigned IPs and it seems like at a certain point (and I don't know how many) you either get assigned the same IP as someone else or something else is happening and you get disconnected - until i soft reset it and it works again which takes 30 secs. I'd say my tablet, my PC, my sisters iPad, 2 laptops and a netbook is the most that can be connected at one time so that is 6 but that should be fine. The only way I know this is the problem is because I turned on my tablet and I was online on my PC, got disconnected but my tablet was still connected, this is just after i turned the tablet on so I know my router is having difficulty with IPs, it is like it assigned the same IP to the tablet which then clashed with my desktop and knocked me off. I see that sometimes the following solves it as well so I wrote a batch file with a menu to execute these commands as I have to do it so often. ipconfig /release ipconfig /flushdns ipconfig /renew Any ideas? Or shall I just get a new router as this one is old and maybe can't handle giving out that many IPs? Cheers!

    Read the article

  • Virtual Wifi on Vista

    - by XGreen
    Hi Guys, Sorry if this is a very dumb question. I have installed the virtualWIFI msi on vista. I assumed that would simply just allow selecting more than one wifi connection with my single card however I don't get much new options. Any help on how to get this running on vista is greatly appreciated.

    Read the article

  • Prevent outgoing traffic unless OpenVPN connection is active using pf.conf on Mac OS X

    - by Nick
    I've been able to deny all connections to external networks unless my OpenVPN connection is active using pf.conf. However, I lose Wi-Fi connectivity if the connection is broken by closing and opening the laptop lid or toggling Wi-Fi off and on again. I'm on Mac OS 10.8.1. I connect to the Web via Wi-Fi (from varying locations, including Internet cafés). The OpenVPN connection is set up with Viscosity. I have the following packet filter rules set up in /etc/pf.conf # Deny all packets unless they pass through the OpenVPN connection wifi=en1 vpn=tun0 block all set skip on lo pass on $wifi proto udp to [OpenVPN server IP address] port 443 pass on $vpn I start the packet filter service with sudo pfctl -e and load the new rules with sudo pfctl -f /etc/pf.conf. I have also edited /System/Library/LaunchDaemons/com.apple.pfctl.plist and changed the line <string>-f</string> to read <string>-ef</string> so that the packet filter launches at system startup. This all seems to works great at first: applications can only connect to the web if the OpenVPN connection is active, so I'm never leaking data over an insecure connection. But, if I close and reopen my laptop lid or turn Wi-Fi off and on again, the Wi-Fi connection is lost, and I see an exclamation mark in the Wi-Fi icon in the status bar. Clicking the Wi-Fi icon shows an "Alert: No Internet connection" message: To regain the connection, I have to disconnect and reconnect Wi-Fi, sometimes five or six times, before the "Alert: No Internet connection" message disappears and I'm able to open the VPN connection again. Other times, the Wi-Fi alert disappears of its own accord, the exclamation mark clears, and I'm able to connect again. Either way, it can take five minutes or more to get a connection again, which can be frustrating. Why does Wi-Fi report "No internet connection" after losing connectivity, and how can I diagnose this issue and fix it?

    Read the article

  • Find the IP of the router between me and main router/gateway?

    - by Crash893
    I have a Netgear router that is the main router/gateway in and out of the network. Then I have a Linksys 54g router with WiFi that we use as are main WiFi access point The Cat5 runs from the router to the WiFi routers LAN port (not WAN). And then if you connect to that WAP you are basically on the network. I want to be able to find out what the IP address of that WAP is but so far I can't figure out how to: I've tried doing a tracert to the gateway IP but I get nothing. I've scanned all the IP addressed in the network. I've gone to the Netgear main router and looked under attached devices but it doesn't say anything. Any ideas on how I can figure out how to administer it? (I do have limited physical access but my attempt to plug into it came back with a faulty IP (in the 169 range where the rest of the office is 192.168...). I never set this router up to begin with so I'm reluctant to just kill it with the reset button because I can't get into see what the settings are set to.

    Read the article

  • Windows 7 freezes on connecting second time to same wifi network

    - by Rakesh Juyal
    I am using Lenovo - y470, which comes with windows 7 home premium. I can connect to my wifi network and there is no issue in that. But the problem comes if the network get disconnected and i again try to connect to same wifi network. As soon as i click on connect my system freezes, and i can not even press ctrl+ alt+ del . The only think i am allowed to do at that time is press and hold power button to shut down the system and restart it again. Please tell me how to resolve this issue. Please let me know if some more information is required. OS: Windows 7 Router: Netgear n-150

    Read the article

  • How to take advantage of two Internet connections (WiFi / Wired) ?

    - by Madhur Ahuja
    I have two separate internet connections, one through WiFi and other Wired. However, generally I have observed that Windows try to use only one ( mostly faster one/ Or Wired by preference - I am not sure). Is there a way I can take advantage of having both ? For example I can have my web browser use the wired one and my torrent software use the Wifi One. PS: This question may be regarded as duplicate but reason I am posting it again is I have not found any concrete answer for it. Two internet Connections, one LAN - how to share?

    Read the article

  • 802.11 Capture Frame

    - by ALi
    I am using wireshark in monitor mode to capture all the frame. I buffered all the QosData in order to calculate the biterate of each station on the network. I calculate the biterate but it is not an accurate value. what i need to know is when the station use the network alone and when it uses it with another station? i know if two station with different wifi card for exemple ( st1 802.11g 54 Mb/s, st2 802.11n 300 Mb/s) if st1 uses alone the line the biterate used is 28 MB/s and if st2 uses alone the network the bit rate increase to approximately 150Mb/s but if the two station use the network at the same time the st1 lost about 80% of its bit rate because of the st1 wifi card thx in advance

    Read the article

  • Netbook (Samsung N220) on Ubuntu 10.04 slows down WiFi for other computers

    - by Joachim
    I encountered a really odd problem with my new netbook. I am running Ubuntu 10.04 on a Samsung N220 Mito. So far everything worked fine. Now I tried the machine for the first time in our work group where we have a wifi (with internet access) for all laptops. The wifi is controlled by a computer running Suse 9.3 which provides a DHCP server and imposes a firewall. At the moment there is only a macbook in the wifi, where no problems with the internet or wifi connection are encountered. Now coming to my actual problem: In addition to the macbook i connect the Samsung N220 to the Wifi. Problem: My download speed is for some reason limited to 70KB/s max. This is neither a limitation of the server/website i browse on, nor a configuration of the netbook: at home i have 500KB/s download speeds. Furthermore, it is not a default limitation for "untrusted" or "new machines" in the wifi, as for instance other new laptops get full speed internet with our wifi. Problem: Once the Samsung N220 is generating traffic in the wifi, the wifi is slowed down dramatically for all other machines: I run a ping to the router from the macbook. The ping times with the N220 ideling are 2-6ms. When I start downloading or browsing in the web with the N220 the ping speed drops to 800ms. Vice versa, when the macbook is generating the traffic the ping of the N220 to the rooter stays constant at around 2-6ms. So clearly, it is some problem originating from my netbook or maybe its treatment in the wifi. Thanks for any help

    Read the article

  • Can't access certain specific IP/domain on Windows 7

    - by jfrobishow
    Been banging my head on the wall for some time now. I have a fresh install of Windows 7 - Ultimate ~x86. Some IPs can't resolve properly, it doesn't matter if I try using Firefox, Chrome or IE I end up with a domain not found (server not found, etc.) I am behind a router, all the other computers aren't affected only this Win 7 machine. It's only certain sites. e.g. xkcd.com, facebook's cdn, google group. Things I have tried: flushdns ipconfig renew Disable IP v6 on the NIC Double checked that the computer was in the right timezone @ the right time. Reinstall the NIC driver. Again 90% of the sites will work but not the major one :P help!!!

    Read the article

  • Add 802.11n to existing 802.11g environment

    - by Andrew Robinson
    I have a small home network that is currently running 802.11g. Two computers that are capable of 802.11n and two devices (a BlackBerry and a Skype phone) that are limited to 802.11g. I have a few neighbors running 802.11g but their signals are very weak. How big an impact will the two G devices have on N speeds? Will they pull the whole network back down to G? These two devices are hardly ever used where as the other N devices are heavily used. If I add an N router to the network (instead of replacing the G) and set my existing G router to use channel 1 with 20MHz bandwidth and then set the N router to use 6 & 11 for 40MHz will I eliminate the overlap and allow for full speed on both networks?

    Read the article

  • How to use ipw3945 on Ubuntu 9.04

    - by Aaron
    Note: uname -a 2.6.28-16-generic cat /etc/issue Ubuntu 9.04 \n \l I have disabled iwl3945: cat /etc/modprobe.d/blacklist.conf | tail -3 blacklist iwl3945 blacklist mac8021 Question: How can I use iwp3945 instead?

    Read the article

  • Disable WLan if Wired/Cable Network is available

    - by ifischer
    The question says it all. All i want is that my W-Lan connection should be disabled whenever a wired connection is available. What would be the easiest way to do that in Ubuntu/Gnome? In all guides (for instance some about guessnet) i found i had to configure my whole network configuration (WPA keys, DHCP, ...), but i find that a bit too complicated for such a simple use case. I just want to disable wlan0 when eth0 is connected.

    Read the article

  • Unable to connect to network

    - by user33750
    Hey guys, I have a question. I have been having problems connecting a new netbook to my network at home. I have an Asus Eeepc 100HAB. I have tried to run a repair on the connection, uninstalled and re-installed the network card, made sure all of the drivers are up-to-date as well. Two caveats: I have a laptop that I recently switched to a wired connection because it wasn't connecting to the network as well, and the netbook connects to an unsecured network i found just fine, only having a problem getting into my home network. Passwords are correct, and the computer where the connection originates from is working fine as well. Any ideas?

    Read the article

  • MBP Bluetooth PAN connection with iPhone 4

    - by Chetan Sachdev
    I am trying to share MBP(OSX 10.8.3) internet connection with iPhone 4 (iOS 6) using Bluetooth PAN(Personal Area Network). Problem is Bluetooth PAN is not getting an ip address. I have tried to renew DHCP lease but nothing works. When I give a Manual IP address, the Bluetooth PAN goes green but doesn't shows the connection in iPhone. Is it possible to share the internet connection via Bluetooth. Note: I don't want to create an Ad-hoc connection over wifi.

    Read the article

  • Internet connectivity issues with one router but work ok with other router

    - by user825904
    I have one Tplink ADSL ROUTER and when i enter username and password on setup page then everything works fine. Now i have one more router Netgear router then when i enter same username and password then interworks ok for some 50% websites but for other 50% websites the page is not loaded and it hangs there. In the sats bar it says website found , waiting for reply and it hnags there and no site is displayed. I wonder which setting is different on these two routers. The Tplink router i have bought is from local shop but netgear router is from different country. Can that make some difference

    Read the article

  • OpenWrt Backfire 10.03 Frequently Becoming Unresponsive (Bridged Client)

    - by Christopher Parker
    I have a Linksys WRT54G version 2 that I've flashed with OpenWrt Backfire 10.03. It's acting as a bridged client using the wl.o driver to give me network access in my home office, which is in a far corner of my house in a position that would make it exceedingly difficult to fish network cabling in through the walls. I have three network-ready devices attached to the device that don't currently support WiFi, including a networked printer. Ever since I migrated from WhiteRussian, which was also set up as a bridged client, to Backfire, the device has been becoming unresponsive, as though the OS itself has crashed or frozen. The WLAN light becomes completely solid and the LAN lights stay mostly solid, blipping off and then back on again maybe once a second or so. They all blink more or less in unison. Is there some way I can diagnose why this is happening so I can fix it? Right now, the only way to fix it is to unplug the device and plug it back in.

    Read the article

  • Aironet 1200's Auto-Channel Feature: When should it be used?

    - by Josh Brower
    In our building we have around 25 1200 series Aironets, with a bit of overlap in some areas. Up until this point, we have had them deployed in alternating 1/6/11 channels, but we are wondering if we would get better performance if we used the auto-channel select feature. In looking around, I have seen comments that this feature should not be used as the WAP does a channel scan only on the radio startup, but I have not found this in any Cisco docs. Anybody have anymore information, or real-world experience with this feature? Thanks! -Josh

    Read the article

  • Setting up VM server access via host MacBook Pro's WiFi hotspot

    - by user7609
    I have a virtual machine (VM) hosted on a MacBook Pro (MBP). There is a server installed on the VM. I'm trying to make this server accessible via MBP's WiFi hotspot so I can see it from my iPhone when connected to the hotspot. The VM is Parallels (latest version) and its OS is Win7 and the MBP is 2013 with Mavericks. With default settings and no hotspot enabled I can access the VM's server from the host OSX. The network setting on the VM is "Shared" and it's IP is 10.211.x.x. When I join the hotspot from another laptop the other laptop gets an IP 169.254.x.x and it can't ping 10.211.x.x or access the server on that VM Is there a combination of settings on the VM and MBP's hotspot such that I can access the VM server from a client on the MPB's hotspot?

    Read the article

  • How to troubleshoot intermittent and irregular connection errors on home network (preferrably Mac client)

    - by Martin
    Hi, I'm experiencing intermittent connection errors in our home network from two different computers, normally "Connection Reset" when browsing, but also other issues such as very slow throughput. I have approximately a network setup as below: ISP-Cable Modem-Dlink DIR 655 Router-(Ethernet)-Fon Router-Mac/Windows laptop Basically, is there a simple way to monitor the network and detect where issues are coming from? Right now we don't know if it is the Fon router, the Dlink router, the modem or the ISP. As the issue is intermittent, is there a software that regularly traceroutes a set of destinations and tests e.g. throughput, something that can help us figure out where in the chain the errors are introduced? The more automatic network monitor, the better.

    Read the article

  • Why my laptop sends ARP request to itself ?

    - by user58859
    I have just started to learn about protocols. While studying the packets in wireshark, I came across a ARP request sent by my machine to my own IP. Here is the details of the packet : No. Time Source Destination Protocol Info 15 1.463563 IntelCor_aa:aa:aa Broadcast ARP Who has 192.168.1.34? Tell 0.0.0.0 Frame 15: 42 bytes on wire (336 bits), 42 bytes captured (336 bits) Arrival Time: Jan 7, 2011 18:51:43.886089000 India Standard Time Epoch Time: 1294406503.886089000 seconds [Time delta from previous captured frame: 0.123389000 seconds] [Time delta from previous displayed frame: 0.123389000 seconds] [Time since reference or first frame: 1.463563000 seconds] Frame Number: 15 Frame Length: 42 bytes (336 bits) Capture Length: 42 bytes (336 bits) [Frame is marked: False] [Frame is ignored: False] [Protocols in frame: eth:arp] [Coloring Rule Name: ARP] [Coloring Rule String: arp] Ethernet II, Src: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa), Dst: Broadcast (ff:ff:ff:ff:ff:ff) Destination: Broadcast (ff:ff:ff:ff:ff:ff) Address: Broadcast (ff:ff:ff:ff:ff:ff) .... ...1 .... .... .... .... = IG bit: Group address (multicast/broadcast) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) Source: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa) Address: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) Type: ARP (0x0806) Address Resolution Protocol (request) Hardware type: Ethernet (0x0001) Protocol type: IP (0x0800) Hardware size: 6 Protocol size: 4 Opcode: request (0x0001) [Is gratuitous: False] Sender MAC address: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa) Sender IP address: 0.0.0.0 (0.0.0.0) Target MAC address: 00:00:00_00:00:00 (00:00:00:00:00:00) Target IP address: 192.168.1.34 (192.168.1.34) Here the sender's mac address is mine(Here I have hiden my mac address). target IP is mine. Why my machine is sending ARP request to itself? I found 3 packets of this type. There was no ARP reply for these packets. Can anybody explain me why it is? (My operating system is windows-7. I am directly connected to a wifi modem. I got these packets as soon as I started my connection.) I want one suggestion also. many places I read that RFC's are enough for study about protocols. I studied the RFC 826 on ARP. I personally feel that is not enough at all. Any suggestion regarding this? Is there more then 1 RFC for a protocol? I want to study about the protocols in very detail. Can anybody guide me for this? Thanks in advance.

    Read the article

  • PDAnet on Android IP on PC is not public IP. Where does the NAT take place, PDAnet or Verizon?

    - by lcbrevard
    When using PDAnet on a PC (Win7 ultimate) to USB tether a Motorola Droid on Verizon 3G the IP address of the PC appears to be public - 64.245.171.115 (64-245-171-115.pools.spcsdns.net) - but connections show as coming from another public IP - 97.14.69.212 (212-sub-97.14.69.myvzw.com). Someone is performing Network Address Translation - either PDAnet or within the Verizon 3G network. Can someone tell me who is doing the NAT? Is it PDAnet or is it at Verizon? Is there any possibility of setting up port forwarding, such that connections to the public IP 97.14.69.212 (212-sub-97.14.69.myvzw.com) are forward to the PC? We are testing a network protocol that requires either a true public IP or forwarding a range of ports from the public Internet to the system on which the software runs (actually Linux hosted by VMware Player or Workstation on a PC running Windows).

    Read the article

  • Pushing WiFi configuration through Active Directory

    - by Hank Gettinger
    I'm trying to push wifi settings to client computers through Active Directory, something that will add a defaul SSID to connect to and a WPA password. The only thing I've heard of is a script by Aruba labs called wificfg_xp.exe on a couple of forums (Here and here), but the link to the download page is always broken. Does any one know of an alternative way to download this file, or another way to push these settings with AD?

    Read the article

  • Access Methods to a computer Using MAC Address

    - by Dimal Chandrasiri
    I have my own wifi network at home & recently when I checked the active clients on the wifi I found out the there is one active client. Router shows the MAC address of this client and I want to Access this computer in order to let him know that he's doing a wrong thing. I dont intent to do any harm to his data. I just want to know a method to send him a message saying "Buy you own wifi". How can I achieve this using a windows 8 computer. Is there any specific softwares that I can use or will the netsend command do the trick! Thank you.

    Read the article

< Previous Page | 82 83 84 85 86 87 88 89 90 91 92 93  | Next Page >