Search Results

Search found 20755 results on 831 pages for 'custom map'.

Page 798/831 | < Previous Page | 794 795 796 797 798 799 800 801 802 803 804 805  | Next Page >

• Sonicwall VPN, Domain Controller Issues

  - by durilai

  I am trying to get the domain logon script to execute when I connect to VPN. I have a SonicWall 4060PRO, with the SonicOS Enhanced 4.2.0.0-10e. The VPN connects successfully, but the script does not execute. I am posting the log below, but I see two issues. The first is the inability to connect to domain. 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX NetGetDCName failed: Could not find domain controller for this domain. The second is the failure of the script. 2009/12/18 19:49:53:466 Warning XXX.XXX.XXX.XXX Failed to execute script file \DT-WIN7netlogondomain.bat, Last Error: The network name cannot be found.. I assume the second issue is caused because of the first, also on the second issue it seems to be trying to get the logon script from my local PC, not the server. Finally, the DC can be pinged and reached by its computer name once the VPN is connected. The shares that the script is tring to map can be mapped manually. Any help is appreciated. 2009/12/18 19:49:31:063 Information The connection "GroupVPN_0006B1030980" has been enabled. 2009/12/18 19:49:32:223 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 1 negotiation. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX Starting aggressive mode phase 1 exchange. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX NAT Detected: Local host is behind a NAT device. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX The SA lifetime for phase 1 is 28800 seconds. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX Phase 1 has completed. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX Received XAuth request. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX XAuth has requested a username but one has not yet been specified. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX Sending phase 1 delete. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX User authentication information is needed to complete the connection. 2009/12/18 19:49:32:393 Information An incoming ISAKMP packet from XXX.XXX.XXX.XXX was ignored. 2009/12/18 19:49:36:962 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 1 negotiation. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX Starting aggressive mode phase 1 exchange. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX NAT Detected: Local host is behind a NAT device. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX The SA lifetime for phase 1 is 28800 seconds. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX Phase 1 has completed. 2009/12/18 19:49:37:094 Information XXX.XXX.XXX.XXX Received XAuth request. 2009/12/18 19:49:37:100 Information XXX.XXX.XXX.XXX Sending XAuth reply. 2009/12/18 19:49:37:110 Information XXX.XXX.XXX.XXX Received initial contact notify. 2009/12/18 19:49:37:153 Information XXX.XXX.XXX.XXX Received XAuth status. 2009/12/18 19:49:37:154 Information XXX.XXX.XXX.XXX Sending XAuth acknowledgement. 2009/12/18 19:49:37:154 Information XXX.XXX.XXX.XXX User authentication has succeeded. 2009/12/18 19:49:37:247 Information XXX.XXX.XXX.XXX Received request for policy version. 2009/12/18 19:49:37:253 Information XXX.XXX.XXX.XXX Sending policy version reply. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX Received policy change is not required. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX Sending policy acknowledgement. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX The configuration for the connection is up to date. 2009/12/18 19:49:37:377 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 2 negotiation with 10.10.10.0/255.255.255.0:BOOTPC:BOOTPS:UDP. 2009/12/18 19:49:37:377 Information XXX.XXX.XXX.XXX Starting quick mode phase 2 exchange. 2009/12/18 19:49:37:472 Information XXX.XXX.XXX.XXX The SA lifetime for phase 2 is 28800 seconds. 2009/12/18 19:49:37:472 Information XXX.XXX.XXX.XXX Phase 2 with 10.10.10.0/255.255.255.0:BOOTPC:BOOTPS:UDP has completed. 2009/12/18 19:49:37:896 Information Renewing IP address for the virtual interface (00-60-73-4C-3F-45). 2009/12/18 19:49:40:189 Information The virtual interface has been added to the system with IP address 10.10.10.112. 2009/12/18 19:49:40:319 Information The system ARP cache has been flushed. 2009/12/18 19:49:40:576 Information XXX.XXX.XXX.XXX NetWkstaUserGetInfo returned: user: Dustin, logon domain: DT-WIN7, logon server: DT-WIN7 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX NetGetDCName failed: Could not find domain controller for this domain. 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX calling NetUserGetInfo: Server: , User: Dustin, level: 3 2009/12/18 19:49:53:460 Information XXX.XXX.XXX.XXX NetUserGetInfo returned: home dir: , remote dir: , logon script: 2009/12/18 19:49:53:466 Warning XXX.XXX.XXX.XXX Failed to execute script file \DT-WIN7netlogondomain.bat, Last Error: The network name cannot be found..

  Read the article

• ERROR: Attempted to read or write protected memory. This is often an indication that other memory is corrupt

  - by SPSamL

  I get this error after having edited a few pages in SharePoint 2010. I have to do an IISReset on both front ends to get this to resolve. I don't know how to fix it or even what else to supply here, but please let me know as the resets now happen several times per day. Log Name: Application Source: ASP.NET 2.0.50727.0 Date: 1/26/2011 11:12:48 AM Event ID: 1309 Task Category: Web Event Level: Warning Keywords: Classic User: N/A Computer: PINTSPSFE02.samcstl.org Description: Event code: 3005 Event message: An unhandled exception has occurred. Event time: 1/26/2011 11:12:48 AM Event time (UTC): 1/26/2011 5:12:48 PM Event ID: c52fb336b7f147a3913fff3617a99d57 Event sequence: 4965 Event occurrence: 2178 Event detail code: 0 Application information: Application domain: /LM/W3SVC/1449762715/ROOT-2-129405348166941887 Trust level: WSS_Minimal Application Virtual Path: / Application Path: C:\inetpub\wwwroot\wss\VirtualDirectories\80\ Machine name: PINTSPSFE02 Process information: Process ID: 5928 Process name: w3wp.exe Account name: SAMC\MossAppPool Exception information: Exception type: AccessViolationException Exception message: Attempted to read or write protected memory. This is often an indication that other memory is corrupt. Request information: Request URL: http://mosscluster/Pages/Home.aspx Request path: /Pages/Home.aspx User host address: 10.3.60.26 User: SAMC\BARNMD Is authenticated: True Authentication Type: NTLM Thread account name: SAMC\MossAppPool Thread information: Thread ID: 110 Thread account name: SAMC\MossAppPool Is impersonating: False Stack trace: at Microsoft.Office.Server.ObjectCache.SPCache.MossObjectCache_Tracked.Delete(String key, Boolean recursive, DeletionReason reason) at Microsoft.Office.Server.ObjectCache.SPCache.MossObjectCache_Tracked.Get(String key) at Microsoft.Office.Server.ObjectCache.SPCache.Get(String objectTypeName, String id) at Microsoft.Office.Server.Administration.UserProfileServiceProxy.GetPartitionPropertiesCache(Guid applicationID) at Microsoft.Office.Server.Administration.UserProfileApplicationProxy.get_PartitionPropertiesCache() at Microsoft.Office.Server.Administration.UserProfileApplicationProxy.DataCache.get_PartitionProperties() at Microsoft.Office.Server.Administration.UserProfileApplicationProxy.GetMySitePortalUrl(SPUrlZone zone, Guid partitionID) at Microsoft.Office.Server.Administration.UserProfileApplicationProxy.GetMySitePortalUrl(SPUrlZone zone, SPServiceContext serviceContext) at Microsoft.Office.Server.WebControls.MyLinksRibbon.EnsureMySiteUrls() at Microsoft.Office.Server.WebControls.MyLinksRibbon.get_PortalMySiteUrlAvailable() at Microsoft.Office.Server.WebControls.MyLinksRibbon.OnLoad(EventArgs e) at System.Web.UI.Control.LoadRecursive() at System.Web.UI.Control.LoadRecursive() at System.Web.UI.Control.LoadRecursive() at System.Web.UI.Control.LoadRecursive() at System.Web.UI.Control.LoadRecursive() at System.Web.UI.Control.LoadRecursive() at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) Custom event details: Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="ASP.NET 2.0.50727.0" /> <EventID Qualifiers="32768">1309</EventID> <Level>3</Level> <Task>3</Task> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2011-01-26T17:12:48.000000000Z" /> <EventRecordID>35834</EventRecordID> <Channel>Application</Channel> <Computer>PINTSPSFE02.samcstl.org</Computer> <Security /> </System> <EventData> <Data>3005</Data> <Data>An unhandled exception has occurred.</Data> <Data>1/26/2011 11:12:48 AM</Data> <Data>1/26/2011 5:12:48 PM</Data> <Data>c52fb336b7f147a3913fff3617a99d57</Data> <Data>4965</Data> <Data>2178</Data> <Data>0</Data> <Data>/LM/W3SVC/1449762715/ROOT-2-129405348166941887</Data> <Data>WSS_Minimal</Data> <Data>/</Data> <Data>C:\inetpub\wwwroot\wss\VirtualDirectories\80\</Data> <Data>PINTSPSFE02</Data> <Data> </Data> <Data>5928</Data> <Data>w3wp.exe</Data> <Data>SAMC\MossAppPool</Data> <Data>AccessViolationException</Data> <Data></Data> <Data>http://mosscluster/Pages/Home.aspx</Data> <Data>/Pages/Home.aspx</Data> <Data>10.3.60.26</Data> <Data>SAMC\BARNMD</Data> <Data>True</Data> <Data>NTLM</Data> <Data>SAMC\MossAppPool</Data> <Data>110</Data> <Data>SAMC\MossAppPool</Data> <Data>False</Data> <Data> at Microsoft.Office.Server.ObjectCache.SPCache.MossObjectCache_Tracked.Delete(String key, Boolean recursive, DeletionReason reason) at Microsoft.Office.Server.ObjectCache.SPCache.MossObjectCache_Tracked.Get(String key) at Microsoft.Office.Server.ObjectCache.SPCache.Get(String objectTypeName, String id) at Microsoft.Office.Server.Administration.UserProfileServiceProxy.GetPartitionPropertiesCache(Guid applicationID) at Microsoft.Office.Server.Administration.UserProfileApplicationProxy.get_PartitionPropertiesCache() at Microsoft.Office.Server.Administration.UserProfileApplicationProxy.DataCache.get_PartitionProperties() at Microsoft.Office.Server.Administration.UserProfileApplicationProxy.GetMySitePortalUrl(SPUrlZone zone, Guid partitionID) at Microsoft.Office.Server.Administration.UserProfileApplicationProxy.GetMySitePortalUrl(SPUrlZone zone, SPServiceContext serviceContext) at Microsoft.Office.Server.WebControls.MyLinksRibbon.EnsureMySiteUrls() at Microsoft.Office.Server.WebControls.MyLinksRibbon.get_PortalMySiteUrlAvailable() at Microsoft.Office.Server.WebControls.MyLinksRibbon.OnLoad(EventArgs e) at System.Web.UI.Control.LoadRecursive() at System.Web.UI.Control.LoadRecursive() at System.Web.UI.Control.LoadRecursive() at System.Web.UI.Control.LoadRecursive() at System.Web.UI.Control.LoadRecursive() at System.Web.UI.Control.LoadRecursive() at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) </Data> </EventData> </Event>

  Read the article

• Using pfSense, OpenVPN Connects but Still Can't See the Network

  - by nicorellius

  I am having an OpenVPN issue. I have a pfSense box at home configured to allow traffic through a VPN tunnel. The client computer is Windows XP Home, behind a standard Comcast connection and a Netgear wireless router. I use OpenVPN to access my work network (from where I am trying to get out of in this post) from home (with an XP Pro machine behind pfSense), and this works fine. The client config is similar but has the changes specific to my setup... Here is my XP Home config: client dev tun proto tcp remote pfsense.*.org 1194 (starred out by me) resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server comp-lzo verb 3 When I launch the OpenVPN GUI, the Tunnel TAP network connection turns red, and I can right-click that to connect to the server. Everything seems to work fine until I browse for the actual network. The Tunnel TAP connection turns green and it says connected to 10.1.1.6 (I have tried different IP pools here too with no luck). I can see the internal network fine, but my home network behind pfSense is not there. I have tried browsing there by using Tools Map Network Drive, using the browser, with no success. When I open the command line on the client and use the ipconfig -all command, I get the following: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TAP-Win32 Adapter V9 Physical Address. . . . . . . . . : *** (starred out by me) Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 10.1.1.6 Subnet Mask . . . . . . . . . . . : 255.255.255.252 Default Gateway . . . . . . . . . : DHCP Server . . . . . . . . . . . : 10.1.1.5 Lease Obtained. . . . . . . . . . : Monday, March 15, 2010 1:18:37 PM Lease Expires . . . . . . . . . . : Tuesday, March 15, 2011 1:18:37 PM I noticed that the default gateway is not present. Could this be my problem? I am still relatively new to firewalls, VPN, and network configuration so I'm sure I am messing up something simple. Oh yah, I should note that I have firewall rules configured for pfSense to allow traffic through the WAN and the LAN. At first there was just the WAN firewall rule, because that is what I got from the literature I was reading. I then created a LAN rule as well, but I'm not sure if this was correct. Neither way works, though. Screen shots below: Any help is much appreciated.

  Read the article

• Can't start httpd 2.4.9 with self-signed SSL certificate

  - by Smollet

  I cannot start the httpd 2.4.9 (tried 2.4.x too) on CentOS 6.5 with the simplest SSL config possible. The openssl version installed on the machine is OpenSSL 1.0.1e-fips 11 Feb 2013 (I've upgraded it using 'yum update' to the latest patched version as well) I have compiled and installed the httpd 2.4.9 using the following commands: ./configure --enable-ssl --with-ssl=/usr/local/ssl/ --enable-proxy=shared --enable-proxy_wstunnel=shared --with-apr=apr-1.5.1/ --with-apr-util=apr-util-1.5.3/ make make install Now I'm generating the default self-signed certificate as described in the CentOS HowTo: openssl genrsa -out ca.key 2048 openssl req -new -key ca.key -out ca.csr openssl x509 -req -days 365 -in ca.csr -signkey ca.key -out ca.crt cp ca.crt /etc/pki/tls/certs cp ca.key /etc/pki/tls/private/ca.key cp ca.csr /etc/pki/tls/private/ca.csr Here is my httpd-ssl.conf file: Listen 443 SSLCipherSuite HIGH:MEDIUM:!aNULL:!MD5 SSLPassPhraseDialog builtin SSLSessionCache "shmcb:/usr/local/apache2/logs/ssl_scache(512000)" SSLSessionCacheTimeout 300 <VirtualHost *:443> SSLEngine on SSLCertificateFile /etc/pki/tls/certs/ca.crt SSLCertificateKeyFile /etc/pki/tls/private/ca.key <FilesMatch "\.(cgi|shtml|phtml|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory "/usr/local/apache2/cgi-bin"> SSLOptions +StdEnvVars </Directory> BrowserMatch "MSIE [2-5]" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 CustomLog "/usr/local/apache2/logs/ssl_request_log" \ "%t %h %{SSL_PROTOCOL}x %{SSL_CIPHER}x \"%r\" %b" </VirtualHost> when I start httpd using bin/apachectl -k start I get following errors in the error_log: Wed Jun 04 00:29:27.995654 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01887: Init: Initializing (virtual) servers for SSL [Wed Jun 04 00:29:27.995726 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:29:27.995863 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:29:27.996111 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_util_ssl.c(343): AH02412: [192.168.9.128:443] Cert matches for name '192.168.9.128' [subject: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / issuer: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / serial: AF04AF31799B7695 / notbefore: Jun 3 22:26:45 2014 GMT / notafter: Jun 3 22:26:45 2015 GMT] [Wed Jun 04 00:29:27.996122 2014] [ssl:info] [pid 24021:tid 139640404293376] AH02568: Certificate and private key 192.168.9.128:443:0 configured from /etc/pki/tls/certs/ca.crt and /etc/pki/tls/private/ca.key [Wed Jun 04 00:29:27.996209 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:29:27.996280 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:29:27.996295 2014] [ssl:emerg] [pid 24021:tid 139640404293376] AH02572: Failed to configure at least one certificate and key for 192.168.9.128:443 [Wed Jun 04 00:29:27.996303 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:0906D06C:PEM routines:PEM_read_bio:no start line (Expecting: DH PARAMETERS) -- Bad file contents or format - or even just a forgotten SSLCertificateKeyFile? [Wed Jun 04 00:29:27.996308 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:0906D06C:PEM routines:PEM_read_bio:no start line (Expecting: EC PARAMETERS) -- Bad file contents or format - or even just a forgotten SSLCertificateKeyFile? [Wed Jun 04 00:29:27.996318 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:140A80B1:SSL routines:SSL_CTX_check_private_key:no certificate assigned [Wed Jun 04 00:29:27.996321 2014] [ssl:emerg] [pid 24021:tid 139640404293376] AH02312: Fatal error initialising mod_ssl, exiting. AH00016: Configuration Failed I then try to generate missing DH PARAMETERS and EC PARAMETERS: openssl dhparam -outform PEM -out dhparam.pem 2048 openssl ecparam -out ec_param.pem -name prime256v1 cat dhparam.pem ec_param.pem >> /etc/pki/tls/certs/ca.crt And it mitigates the error but the next comes out: [Wed Jun 04 00:34:05.021438 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01887: Init: Initializing (virtual) servers for SSL [Wed Jun 04 00:34:05.021487 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:34:05.021874 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:34:05.022050 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_util_ssl.c(343): AH02412: [192.168.9.128:443] Cert matches for name '192.168.9.128' [subject: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / issuer: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / serial: AF04AF31799B7695 / notbefore: Jun 3 22:26:45 2014 GMT / notafter: Jun 3 22:26:45 2015 GMT] [Wed Jun 04 00:34:05.022066 2014] [ssl:info] [pid 24089:tid 140719371077376] AH02568: Certificate and private key 192.168.9.128:443:0 configured from /etc/pki/tls/certs/ca.crt and /etc/pki/tls/private/ca.key [Wed Jun 04 00:34:05.022285 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(1016): AH02540: Custom DH parameters (2048 bits) for 192.168.9.128:443 loaded from /etc/pki/tls/certs/ca.crt [Wed Jun 04 00:34:05.022389 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(1030): AH02541: ECDH curve prime256v1 for 192.168.9.128:443 specified in /etc/pki/tls/certs/ca.crt [Wed Jun 04 00:34:05.022397 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:34:05.022464 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:34:05.022478 2014] [ssl:emerg] [pid 24089:tid 140719371077376] AH02572: Failed to configure at least one certificate and key for 192.168.9.128:443 [Wed Jun 04 00:34:05.022488 2014] [ssl:emerg] [pid 24089:tid 140719371077376] SSL Library Error: error:140A80B1:SSL routines:SSL_CTX_check_private_key:no certificate assigned [Wed Jun 04 00:34:05.022491 2014] [ssl:emerg] [pid 24089:tid 140719371077376] AH02312: Fatal error initialising mod_ssl, exiting. AH00016: Configuration Failed I have tried to generate the simple certificate/key pair exactly as described in the httpd docs Unfortunately, I still get exact same errors as above. I've seen a bug report with the similar issue: https://issues.apache.org/bugzilla/show_bug.cgi?id=56410 But the openssl version I have is reported as working there. I've also tried to apply the patch from the report as well as build the latest 2.4.x branch with no success, I get the same errors as above. I have also tried to create a short chain of certificates and set the root CA certificate using SSLCertificateChainFile directive. That didn't help either, I get exact same errors as above. I'm not interested in setting up hardened security, etc. The only thing I need is to start httpd with the simplest SSL config possible to continue testing proxy config for the mod_proxy_wstunnel Had anybody encountered and solved this issue? Is my sequence for creating a self-signed certificate incorrect? I'd appreciate any help very much!

  Read the article

• straight to grub prompt on boot

  - by cheshirekow

  I am very lost. I did a fresh install of Ubuntu 10.04 on a laptop. First reboot was fine. I ran all the recommended upgrades, and now every time I start I get just a grub>_ prompt. No error message, just the prompt, and a little banner at the top saying grub's version and telling me that I have minimal bash style editing. I've tried: 1) Re-installing grub via sudo grub-install sda (There is only one disk with only two partitions, one primary, and one for swap) 2) Changed GRUB_HIDDEN_TIMEOUT=10 GRUB_TIMEOUT=30 GRUB_CMDLINE_LINUX_DEFAULT="rootdelay=90" GRUB_CMDLINE_LINUX="rootdelay=90" in /etc/default/grub. No luck. I can boot with the following: grub> set root=(hd0,1) grub> probe (hd0,1) -u c00fadde-f7e8-45e7-a4da-0235605f756 grub> linux /boot/vmlinuz-2.6.32-21-generic root=UUID=c00fadde-f7e8-45e7-a4da-0235605f756 rootdelay=90 grub> initrd /boot/initrd.img-2.6.32-21-generic grub> boot And then everything seems to be fine from there. From the grub prompt if I try configfile /boot/grub/grub.cfg The screen clears and I get another grub prompt. So, seriously, what could the problem be? edit: Full text of /boot/grub/grub.cfg # # DO NOT EDIT THIS FILE # # It is automatically generated by /usr/sbin/grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then load_env fi set default="0" if [ ${prev_saved_entry} ]; then set saved_entry=${prev_saved_entry} save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z ${boot_once} ]; then saved_entry=${chosen} save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n ${have_grubenv} ]; then if [ -z ${boot_once} ]; then save_env recordfail; fi; fi } insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 insmod gfxterm insmod vbe if terminal_output gfxterm ; then true ; else # For backward compatibility with versions of terminal.mod that don't # understand terminal_output terminal gfxterm fi fi insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 set locale_dir=($root)/boot/grub/locale set lang=en insmod gettext if [ ${recordfail} = 1 ]; then set timeout=-1 else set timeout=30 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.32-21-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 linux /boot/vmlinuz-2.6.32-21-generic root=UUID=c00fadde-f7e8-45e7-a4da-0235c605f756 ro rootdelay=90 rootdelay=90 initrd /boot/initrd.img-2.6.32-21-generic } menuentry 'Ubuntu, with Linux 2.6.32-21-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 echo 'Loading Linux 2.6.32-21-generic ...' linux /boot/vmlinuz-2.6.32-21-generic root=UUID=c00fadde-f7e8-45e7-a4da-0235c605f756 ro single rootdelay=90 echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.32-21-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### if [ ${timeout} != -1 ]; then if sleep --verbose --interruptible 10 ; then set timeout=0 fi fi ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### output of update-grub Generating grub.cfg ... Found linux image: /boot/vmlinuz-2.6.32-21-generic Found initrd image: /boot/initrd.img-2.6.32-21-generic Found memtest86+ image: /boot/memtest86+.bin done contents of /boot total 14280 -rw-r--r-- 1 root root 640617 2010-04-16 09:01 abi-2.6.32-21-generic -rw-r--r-- 1 root root 115847 2010-04-16 09:01 config-2.6.32-21-generic drwxr-xr-x 3 root root 4096 2010-09-08 02:42 grub -rw-r--r-- 1 root root 7968754 2010-09-02 01:49 initrd.img-2.6.32-21-generic -rw-r--r-- 1 root root 160280 2010-03-23 05:37 memtest86+.bin -rw-r--r-- 1 root root 1687378 2010-04-16 09:01 System.map-2.6.32-21-generic -rw-r--r-- 1 root root 1196 2010-04-16 09:03 vmcoreinfo-2.6.32-21-generic -rw-r--r-- 1 root root 4029792 2010-04-16 09:01 vmlinuz-2.6.32-21-generic

  Read the article

• DRBD Not syncing between my nodes

  - by Mike Curry

  Some version info: Operating system is Ubuntu 11.10, on EC2, kernel is 3.0.0-16-virtual and the application info is: Version: 8.3.11 (api:88) GIT-hash: 0de839cee13a4160eed6037c4bddd066645e23c5 build by buildd@allspice, 2011-07-05 19:51:07 Getting some strange errors in dmesg (seen below) as well, there is no replication happening. I have made my first node primary and its showing: drbd driver loaded OK; device status: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 m:res cs ro ds p mounted fstype 0:r0 StandAlone Primary/Unknown UpToDate/DUnknown r----s ext3 my secondary node is showing: drbd driver loaded OK; device status: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 m:res cs ro ds p mounted fstype 0:r0 StandAlone Secondary/Unknown Inconsistent/DUnknown r----s Showing /proc/drbd on the master shows: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 0: cs:StandAlone ro:Primary/Unknown ds:UpToDate/DUnknown r----s ns:0 nr:0 dw:4 dr:1073 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:262135964 Showing /proc/drbd on the slave shows that there is nothing being transfered... version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 0: cs:StandAlone ro:Secondary/Unknown ds:Inconsistent/DUnknown r----s ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:262135964 Here is my config... resource r0 { protocol C; startup { wfc-timeout 15; degr-wfc-timeout 60; } net { cram-hmac-alg sha1; shared-secret "test123; } on drbd01 { device /dev/drbd0; disk /dev/xvdm; address 23.XX.XX.XX:7788; # blocked out ip meta-disk internal; } on drbd02 { device /dev/drbd0; disk /dev/xvdm; address 184.XX.XX.XX:7788; #blocked out ip meta-disk internal; } } I have run the following on the master: sudo drbdadm -- --overwrite-data-of-peer primary all There is no firewall between the systems. Here is the dmesg with some errors: [2285172.969955] drbd: initialized. Version: 8.3.11 (api:88/proto:86-96) [2285172.969960] drbd: srcversion: DA5A13F16DE6553FC7CE9B2 [2285172.969962] drbd: registered as block device major 147 [2285172.969965] drbd: minor_table @ 0xffff88000276ea00 [2285173.000952] block drbd0: Starting worker thread (from drbdsetup [1300]) [2285173.003971] block drbd0: disk( Diskless -> Attaching ) [2285173.006150] block drbd0: No usable activity log found. [2285173.006154] block drbd0: Method to ensure write ordering: flush [2285173.006158] block drbd0: max BIO size = 4096 [2285173.006165] block drbd0: drbd_bm_resize called with capacity == 524271928 [2285173.008512] block drbd0: resync bitmap: bits=65533991 words=1023969 pages=2000 [2285173.008518] block drbd0: size = 250 GB (262135964 KB) [2285173.079566] block drbd0: bitmap READ of 2000 pages took 17 jiffies [2285173.081189] block drbd0: recounting of set bits took additional 1 jiffies [2285173.081194] block drbd0: 250 GB (65533991 bits) marked out-of-sync by on disk bit-map. [2285173.081203] block drbd0: Suspended AL updates [2285173.081210] block drbd0: disk( Attaching -> UpToDate ) [2285173.081214] block drbd0: attached to UUIDs 1C1291D39584C1D1:0000000000000004:0000000000000000:0000000000000000 [2285173.095016] block drbd0: conn( StandAlone -> Unconnected ) [2285173.095046] block drbd0: Starting receiver thread (from drbd0_worker [1301]) [2285173.099297] block drbd0: receiver (re)started [2285173.099304] block drbd0: conn( Unconnected -> WFConnection ) [2285173.099330] block drbd0: bind before connect failed, err = -99 [2285173.099346] block drbd0: conn( WFConnection -> Disconnecting ) [2285173.295788] block drbd0: Discarding network configuration. [2285173.295815] block drbd0: Connection closed [2285173.295826] block drbd0: conn( Disconnecting -> StandAlone ) [2285173.295840] block drbd0: receiver terminated [2285173.295844] block drbd0: Terminating drbd0_receiver Edit: Reading some other similar issues, it was suggested to do a 'drbdadm dump all', so I figured it couldn't hurt. ubuntu@drbd01:~$ drbdadm dump all /etc/drbd.conf:19: in resource r0, on drbd01: IP 23.XX.XX.XX not found on this host. and on slave: root@drbd02:~# drbdadm dump all /etc/drbd.conf:25: in resource r0, on drbd02: IP 184.XX.XX.XX not found on this host. Strange it doesn't find its own ip, however, this is an Amazon EC2 system using an elastic IP... here are my ipconfigs for both... master: ubuntu@drbd01:~$ ifconfig eth0 Link encap:Ethernet HWaddr 22:00:0a:1c:27:11 inet addr:10.28.39.17 Bcast:10.28.39.63 Mask:255.255.255.192 inet6 addr: fe80::2000:aff:fe1c:2711/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1569 errors:0 dropped:0 overruns:0 frame:0 TX packets:1169 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:124409 (124.4 KB) TX bytes:213601 (213.6 KB) Interrupt:26 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) slave: root@drbd02:~# ifconfig eth0 Link encap:Ethernet HWaddr 12:31:3f:00:14:9d inet addr:10.160.27.107 Bcast:10.160.27.255 Mask:255.255.254.0 inet6 addr: fe80::1031:3fff:fe00:149d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:915 errors:0 dropped:0 overruns:0 frame:0 TX packets:774 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:75381 (75.3 KB) TX bytes:109673 (109.6 KB) Interrupt:26 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

  Read the article

• Unable to SSH into EC2 instance on Fedora 17

  - by abhishek

  I did following steps But I am not able to SSH to it(Same steps work fine on Fedora 14 image). I am getting Permission denied (publickey,gssapi-keyex,gssapi-with-mic) I created new instance using fedora 17 amazon community image(ami-2ea50247). I copied my ssh keys under /home/usertest/.ssh/ after creating a usertest I have SELINUX=disabled here is Debug info: $ ssh -vvv ec2-54-243-101-41.compute-1.amazonaws.com ssh -vvv ec2-54-243-101-41.compute-1.amazonaws.com OpenSSH_5.2p1, OpenSSL 1.0.0b-fips 16 Nov 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to ec2-54-243-101-41.compute-1.amazonaws.com [54.243.101.41] port 22. debug1: Connection established. debug1: identity file /home/usertest/.ssh/identity type -1 debug1: identity file /home/usertest/.ssh/id_rsa type -1 debug3: Not a RSA1 key file /home/usertest/.ssh/id_dsa. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug2: key_type_from_name: unknown key type 'Proc-Type:' debug3: key_read: missing keytype debug2: key_type_from_name: unknown key type 'DEK-Info:' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/usertest/.ssh/id_dsa type 2 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9 debug1: match: OpenSSH_5.9 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.2 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 131/256 debug2: bits set: 506/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: check_host_in_hostfile: filename /home/usertest/.ssh/known_hosts debug3: check_host_in_hostfile: match line 17 debug3: check_host_in_hostfile: filename /home/usertest/.ssh/known_hosts debug3: check_host_in_hostfile: match line 17 debug1: Host 'ec2-54-243-101-41.compute-1.amazonaws.com' is known and matches the RSA host key. debug1: Found key in /home/usertest/.ssh/known_hosts:17 debug2: bits set: 500/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/usertest/.ssh/identity ((nil)) debug2: key: /home/usertest/.ssh/id_rsa ((nil)) debug2: key: /home/usertest/.ssh/id_dsa (0x7f904b5ae260) debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic debug3: start over, passed a different list publickey,gssapi-keyex,gssapi-with-mic debug3: preferred gssapi-with-mic,publickey,keyboard-interactive,password debug3: authmethod_lookup gssapi-with-mic debug3: remaining preferred: publickey,keyboard-interactive,password debug3: authmethod_is_enabled gssapi-with-mic debug1: Next authentication method: gssapi-with-mic debug3: Trying to reverse map address 54.243.101.41. debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_500' not found debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_500' not found debug1: Unspecified GSS failure. Minor code may provide more information debug2: we did not send a packet, disable method debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/usertest/.ssh/identity debug3: no such identity: /home/usertest/.ssh/identity debug1: Trying private key: /home/usertest/.ssh/id_rsa debug3: no such identity: /home/usertest/.ssh/id_rsa debug1: Offering public key: /home/usertest/.ssh/id_dsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic debug2: we did not send a packet, disable method debug1: No more authentication methods to try. Permission denied (publickey,gssapi-keyex,gssapi-with-mic).

  Read the article

• Debian apt dependency mismatch (libc6)

  - by Sean Gordon

  Earlier, I tried to install package via apt-get (cython), but it failed with the Errors were encountered while processing: message, and since then, apt is refusing to install anything. apt-get check output below: root@dix:~# apt-get check Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies: libc6 : Depends: libc-bin (= 2.11.3-2) but 2.11.3-4 is installed libc6-dev : Depends: libc6 (= 2.11.3-4) but 2.11.3-2 is installed libc6-i386 : Depends: libc6 (= 2.11.3-4) but 2.11.3-2 is installed E: Unmet dependencies. Try using -f. Apt/aptitude don't seem to be able to fix this dependency issue, and I don't know what to do. Edit: Running apt-get -f install results in no change, and my sources are all squeeze. Running apt-get update then apt-get dist-upgrade show no change either. Edit 2: I went back to try this again in a new terminal and apt-get -f install gives this error: dpkg: error processing /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb (--unpack): subprocess new pre-installation script killed by signal (Aborted) configured to not write apport reports Errors were encountered while processing: /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb E: Sub-process /usr/bin/dpkg returned an error code (1) Edit 3: Using apt-get clean first, then the previous commands, results in the first error again. Using apt-get -f dist-upgrade gives the below. Reading package lists... Building dependency tree... Reading state information... Correcting dependencies... Done The following packages will be upgraded: apache2 apache2-mpm-prefork apache2-utils apache2.2-bin apache2.2-common at automake base-files bind9 bind9-doc bind9-host bind9utils debian-archive-keyring dnsutils dpkg-dev file host initscripts isc-dhcp-client isc-dhcp-common krb5-multidev libapr1 libbind9-60 libc6 libdns69 libdpkg-perl libexpat1 libexpat1-dev libgc1c2 libgssapi-krb5-2 libgssrpc4 libisc62 libisccc60 libisccfg62 libk5crypto3 libkadm5clnt-mit7 libkadm5srv-mit7 libkdb5-4 libkrb5-3 libkrb5-dev libkrb5support0 liblwres60 libmagic1 libmysqlclient16 libnss3-1d libssl-dev libssl0.9.8 libtiff4 libtiff4-dev libtiffxx0c2 libxi6 libxml2 linux-libc-dev lwresd mysql-client-5.1 mysql-common mysql-server mysql-server-5.1 mysql-server-core-5.1 openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib openssh-client openssh-server openssl procps python python-crypto python-minimal sudo sysv-rc sysvinit sysvinit-utils tzdata tzdata-java 75 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 5 not fully installed or removed. Need to get 0 B/79.9 MB of archives. After this operation, 1,411 kB of additional disk space will be used. (Reading database ... 52241 files and directories currently installed.) Preparing to replace libc6 2.11.3-2 (using .../libc6_2.11.3-4_amd64.deb) ... *** stack smashing detected ***: /usr/bin/perl terminated ======= Backtrace: ========= /lib/libc.so.6(__fortify_fail+0x37)[0x7fdaad9b9f87] /lib/libc.so.6(__fortify_fail+0x0)[0x7fdaad9b9f50] /usr/lib/libperl.so.5.10(Perl_yylex+0x5896)[0x7fdaae343346] [0x8e83a0] ======= Memory map: ======== 00400000-00402000 r-xp 00000000 08:01 525338 /usr/bin/perl 00601000-00602000 rw-p 00001000 08:01 525338 /usr/bin/perl 00602000-0091f000 rw-p 00000000 00:00 0 [heap] 7fdaaca54000-7fdaaca6a000 r-xp 00000000 08:01 393818 /lib/libgcc_s.so.1 7fdaaca6a000-7fdaacc69000 ---p 00016000 08:01 393818 /lib/libgcc_s.so.1 7fdaacc69000-7fdaacc6a000 rw-p 00015000 08:01 393818 /lib/libgcc_s.so.1 7fdaacc6a000-7fdaacc6f000 r-xp 00000000 08:01 524949 /usr/lib/perl5/auto/Locale/gettext/gettext.so 7fdaacc6f000-7fdaace6e000 ---p 00005000 08:01 524949 /usr/lib/perl5/auto/Locale/gettext/gettext.so 7fdaace6e000-7fdaace6f000 rw-p 00004000 08:01 524949 /usr/lib/perl5/auto/Locale/gettext/gettext.so 7fdaace6f000-7fdaace79000 r-xp 00000000 08:01 532753 /usr/lib/perl/5.10.1/auto/Encode/Encode.so 7fdaace79000-7fdaad078000 ---p 0000a000 08:01 532753 /usr/lib/perl/5.10.1/auto/Encode/Encode.so 7fdaad078000-7fdaad079000 rw-p 00009000 08:01 532753 /usr/lib/perl/5.10.1/auto/Encode/Encode.so 7fdaad079000-7fdaad07e000 r-xp 00000000 08:01 525444 /usr/lib/perl/5.10.1/auto/IO/IO.so 7fdaad07e000-7fdaad27d000 ---p 00005000 08:01 525444 /usr/lib/perl/5.10.1/auto/IO/IO.so 7fdaad27d000-7fdaad27e000 rw-p 00004000 08:01 525444 /usr/lib/perl/5.10.1/auto/IO/IO.so 7fdaad27e000-7fdaad299000 r-xp 00000000 08:01 525450 /usr/lib/perl/5.10.1/auto/POSIX/POSIX.so 7fdaad299000-7fdaad498000 ---p 0001b000 08:01 525450 /usr/lib/perl/5.10.1/auto/POSIX/POSIX.so 7fdaad498000-7fdaad49b000 rw-p 0001a000 08:01 525450 /usr/lib/perl/5.10.1/auto/POSIX/POSIX.so 7fdaad49b000-7fdaad49e000 r-xp 00000000 08:01 525436 /usr/lib/perl/5.10.1/auto/Fcntl/Fcntl.so 7fdaad49e000-7fdaad69e000 ---p 00003000 08:01 525436 /usr/lib/perl/5.10.1/auto/Fcntl/Fcntl.so 7fdaad69e000-7fdaad69f000 rw-p 00003000 08:01 525436 /usr/lib/perl/5.10.1/auto/Fcntl/Fcntl.so 7fdaad69f000-7fdaad6a7000 r-xp 00000000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad6a7000-7fdaad8a6000 ---p 00008000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad8a6000-7fdaad8a7000 r--p 00007000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad8a7000-7fdaad8a8000 rw-p 00008000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad8a8000-7fdaad8d6000 rw-p 00000000 00:00 0 7fdaad8d6000-7fdaada2f000 r-xp 00000000 08:01 393822 /lib/libc-2.11.3.so 7fdaada2f000-7fdaadc2e000 ---p 00159000 08:01 393822 /lib/libc-2.11.3.so 7fdaadc2e000-7fdaadc32000 r--p 00158000 08:01 393822 /lib/libc-2.11.3.so 7fdaadc32000-7fdaadc33000 rw-p 0015c000 08:01 393822 /lib/libc-2.11.3.so 7fdaadc33000-7fdaadc38000 rw-p 00000000 00:00 0 7fdaadc38000-7fdaadc4f000 r-xp 00000000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaadc4f000-7fdaade4e000 ---p 00017000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaade4e000-7fdaade4f000 r--p 00016000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaade4f000-7fdaade50000 rw-p 00017000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaade50000-7fdaade54000 rw-p 00000000 00:00 0 7fdaade54000-7fdaaded4000 r-xp 00000000 08:01 393826 /lib/libm-2.11.3.so 7fdaaded4000-7fdaae0d4000 ---p 00080000 08:01 393826 /lib/libm-2.11.3.so 7fdaae0d4000-7fdaae0d5000 r--p 00080000 08:01 393826 /lib/libm-2.11.3.so 7fdaae0d5000-7fdaae0d6000 rw-p 00081000 08:01 393826 /lib/libm-2.11.3.so 7fdaae0d6000-7fdaae0d8000 r-xp 00000000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae0d8000-7fdaae2d8000 ---p 00002000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae2d8000-7fdaae2d9000 r--p 00002000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae2d9000-7fdaae2da000 rw-p 00003000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae2da000-7fdaae43f000 r-xp 00000000 08:01 525387 /usr/lib/libperl.so.5.10.1 7fdaae43f000-7fdaae63e000 ---p 00165000 08:01 525387 /usr/lib/libperl.so.5.10.1 7fdaae63e000-7fdaae647000 rw-p 00164000 08:01 525387 /usr/lib/libperl.so.5.10.1 7fdaae647000-7fdaae665000 r-xp 00000000 08:01 393819 /lib/ld-2.11.3.so 7fdaae854000-7fdaae859000 rw-p 00000000 00:00 0 7fdaae862000-7fdaae864000 rw-p 00000000 00:00 0 7fdaae864000-7fdaae865000 r--p 0001d000 08:01 393819 /lib/ld-2.11.3.so 7fdaae865000-7fdaae866000 rw-p 0001e000 08:01 393819 /lib/ld-2.11.3.so 7fdaae866000-7fdaae867000 rw-p 00000000 00:00 0 7fff9616d000-7fff9618e000 rw-p 00000000 00:00 0 [stack] 7fff961ff000-7fff96200000 r-xp 00000000 00:00 0 [vdso] ffffffffff600000-ffffffffff601000 r--p 00000000 00:00 0 [vsyscall] dpkg: error processing /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb (--unpack): subprocess new pre-installation script killed by signal (Aborted) Errors were encountered while processing: /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb

  Read the article

• Strategy for using snapshots to back up Ubuntu Linux server?

  - by MountainX

  I need some backup advice for my home file server. Here are the mount points, volume groups, logical volumes and used/total space of all the volumes on my Ubuntu 8.10 home file server. / vgA/lvRoot [7.5G/50G] /tmp vgB/lvTmp [195M/30G] /var vgB/lvVar [780M/30G] swap vgB/lvSwap [16.00 GB] /media1 vgC/lvMedia1 [400G/975G] /media2 vgC/lvMedia2 [75G/295G] /boot partition (no volume group) [95M/200M] /video partition (no volume group) [450G/950G] /backups vgD/lvBackupTarget [800G/925G] /home vgE/lvHome [85G/200G] I have just added a 2.0 TB external USB drive that I would like to use to backup everything. (It will be a close fit to get it all on one 2.0 TB drive. I actually have a 2nd external USB drive if needed.) I'd like to backup "/", var, /media1, media2 and /home. I'll deal with /boot and /video separately since they are not logical volumes. For all the logical volumes I'm anticipating taking snapshots and then copying those snapshots to the 2.0 TB external USB drive. I have never done a task like that before. If I do that, I could use the tutorial I found here: http://www.howtoforge.com/linux_lvm_snapshots My questions are: What is the best overall strategy? Is it LVM snapshots, as I'm assuming? How should I prepare, subdivide and mount the 2.0 TB external USB drive? 2.a. Should I create one or more regular partitions or should I create a physical volume with one or more logical volumes? 2.b. Would it be advisable to extactly mirror the source pv/lv layout on the external drive, and if so, is this a good strategy? What's the best way to get the snapshots onto the external drive? dd? Even though this is a strategy question, feedback with actual commands is appreciated. I need step-by-step cookbook-style help because I don't do much server admin work. (Background: This is a home file server that I have rarely had to touch in about 2 years. It has done its job without much intervention. The really old PC that I used to back everything up recently failed, so I'm replacing that with the external USB drive(s) and I'd like to upgrade my backup strategy at the same time. Previously, I just copied stuff from /backups over to the other computer and that would not have made things very easy in a real restore situation. The /backups mount point contains backup copies of "most" of the important data on a file by file basis, but it does not contain copies of /boot, etc. BTW, the actual internal HDD that holds /backups is separate from the other storage devices.) EDIT: I'll propose a strategy... The idea came from a comment here: LVM mirroring VS RAID1 "LVM mirrors are for replication of a logical volume to a different physical volume. It's essentially meant to "move the data to a different disk". The mirror is then broken..." That would fit my requirements well. Here is an ideal situation: establish the LV mirror on the external drive break the link with the mirror create a (persistent) snapshot on the mirror after a week, resync the mirror with the original source and update the mirror break the link and create another snapshot on the mirror. Obviously, the mirror will be like a weekly full backup. And the snapshots on the mirror will represent earlier points in time. If this would work and if it would be time efficient, it would give a nice full & differential type backup on the external drive based on LVM. I have not heard of a strategy like this before. Will it work? Could it be scripted? Thoughts? EDIT 2: Creating Portable DiskSafes With LoopbackFS And LVM Snapshots This article seems intriguing: http://www.howtoforge.com/creating-portable-disksafes-with-loopbackfs-and-lvm-snapshots Unfortunately, I don't understand exactly how to map those ideas to the strategy I'm proposing above. I'm going to ask this last bit as a separate question. I will leave my original question in place because I still desire feedback on the overall best strategy. At this moment I'm assuming it is LVM mirroring in the style of "Creating Portable DiskSafes with LVM Snapshots" but that might be wrong.

  Read the article

• GRUB-2 Bootloader fails to load for lack of floppy drive. Ubuntu 10.4 & Windows XP

  - by kammer

  2010.07.21 while trying to install Ubuntu 10.4 Hello all, I've been trying to install Ubuntu 10.04 on my Dell workstation and am unable to get the Grub-2 bootloader to load properly. It seems to be failing for lack of a floppy drive on the system resulting in an error message that reads : error: fd0 cannot get C/H/S values. I've gone through the Grub-2 page at https://help.ubuntu.com/community/Grub2 to no avail and other sources having similar problems have likewise turned up no solutions. I would certainly appreciate any insight, here's the background: A while back I was trying to install a different version of Linux and had the same problems, then had to set the project aside for a bit. I don't think this has anything to do with Linux or Ubuntu per se, but rather Grub. The system is an old (4-5 years) Dell workstation that has one drive (128 GB) set up for Windows XP and a second new drive (500GB) which I installed for Linux. There is a DVD/CD drive and the system contains no floppy drive at all. In one attempt to get this working I tried modifying the BIOS to indicate there was a floppy drive - this created a failure earlier in the chain with the BIOS failing to load properly, not unexpected, just a shot in the dark at that point. At the moment I am considering just running out to buy and install a cheap floppy drive to see if that helps. I'll never use the thing though so I'd rather find a solution that doesn't require me to spend money on useless hardware. In any case, here's the /boot/grub/grub.cfg contents: # # DO NOT EDIT THIS FILE # # It is automatically generated by /usr/sbin/grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then load_env fi set default="0" if [ ${prev_saved_entry} ]; then set saved_entry=${prev_saved_entry} save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z ${boot_once} ]; then saved_entry=${chosen} save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n ${have_grubenv} ]; then if [ -z ${boot_once} ]; then save_env recordfail; fi; fi } insmod ext2 set root='(hd1,1)' search --no-floppy --fs-uuid --set fbebde47-f488-41b0-9480-337802ecb988 if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 insmod gfxterm insmod vbe if terminal_output gfxterm ; then true ; else # For backward compatibility with versions of terminal.mod that don't # understand terminal_output terminal gfxterm fi fi insmod ext2 set root='(hd1,1)' search --no-floppy --fs-uuid --set fbebde47-f488-41b0-9480-337802ecb988 set locale_dir=($root)/boot/grub/locale set lang=en insmod gettext if [ ${recordfail} = 1 ]; then set timeout=-1 else set timeout=10 fi insmod play play 480 440 1 ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.32-21-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd1,1)' search --no-floppy --fs-uuid --set fbebde47-f488-41b0-9480-337802ecb988 linux /boot/vmlinuz-2.6.32-21-generic root=UUID=fbebde47-f488-41b0-9480-337802ecb988 ro quiet splash initrd /boot/initrd.img-2.6.32-21-generic } menuentry 'Ubuntu, with Linux 2.6.32-21-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd1,1)' search --no-floppy --fs-uuid --set fbebde47-f488-41b0-9480-337802ecb988 echo 'Loading Linux 2.6.32-21-generic ...' linux /boot/vmlinuz-2.6.32-21-generic root=UUID=fbebde47-f488-41b0-9480-337802ecb988 ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.32-21-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod ext2 set root='(hd1,1)' search --no-floppy --fs-uuid --set fbebde47-f488-41b0-9480-337802ecb988 linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod ext2 set root='(hd1,1)' search --no-floppy --fs-uuid --set fbebde47-f488-41b0-9480-337802ecb988 linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Microsoft Windows XP Home Edition (on /dev/sda1)" { insmod ntfs set root='(hd0,1)' search --no-floppy --fs-uuid --set 6ef0d4b4f0d4842d drivemap -s (hd0) ${root} chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### Thoughts anyone? Thanks in advance.

  Read the article

• KVM Slow performance on XP Guest

  - by Gregg Leventhal

  The system is very slow to do anything, even browse a local folder, and CPU sits at 100% frequently. Guest is XP 32 bit. Host is Scientific Linux 6.2, Libvirt 0.10, Guest XP OS shows ACPI Multiprocessor HAL and a virtIO driver for NIC and SCSI. Installed. CPUInfo on host: processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 42 model name : Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz stepping : 7 cpu MHz : 3200.000 cache size : 8192 KB physical id : 0 siblings : 8 core id : 0 cpu cores : 4 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp lm constant_tsc arch_perfmon pebs bts rep_good xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx lahf_lm ida arat epb xsaveopt pln pts dts tpr_shadow vnmi flexpriority ept vpid bogomips : 6784.93 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: <memory unit='KiB'>4194304</memory> <currentMemory unit='KiB'>4194304</currentMemory> <vcpu placement='static' cpuset='0'>1</vcpu> <os> <type arch='x86_64' machine='rhel6.3.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <cpu mode='custom' match='exact'> <model fallback='allow'>SandyBridge</model> <vendor>Intel</vendor> <feature policy='require' name='vme'/> <feature policy='require' name='tm2'/> <feature policy='require' name='est'/> <feature policy='require' name='vmx'/> <feature policy='require' name='osxsave'/> <feature policy='require' name='smx'/> <feature policy='require' name='ss'/> <feature policy='require' name='ds'/> <feature policy='require' name='tsc-deadline'/> <feature policy='require' name='dtes64'/> <feature policy='require' name='ht'/> <feature policy='require' name='pbe'/> <feature policy='require' name='tm'/> <feature policy='require' name='pdcm'/> <feature policy='require' name='ds_cpl'/> <feature policy='require' name='xtpr'/> <feature policy='require' name='acpi'/> <feature policy='require' name='monitor'/> <feature policy='force' name='sse'/> <feature policy='force' name='sse2'/> <feature policy='force' name='sse4.1'/> <feature policy='force' name='sse4.2'/> <feature policy='force' name='ssse3'/> <feature policy='force' name='x2apic'/> </cpu> <clock offset='localtime'> <timer name='rtc' tickpolicy='catchup'/> </clock> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='qcow2' cache='none'/> <source file='/var/lib/libvirt/images/Server-10-9-13.qcow2'/> <target dev='vda' bus='virtio'/> <alias name='virtio-disk0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x08' function='0x0'/> </disk>

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• Site-to-Site PPTP VPN connection between two Windows Server 2008 R2 servers

  - by steve_eyre

  We have two Windows Server 2008 R2 machines, one in our main office and one in a new office which we have just moved offsite. The main office has previously been handling client-to-server PPTP VPN connections. Now that we have moved our second server out of office, we want to set up a demand-dial or persistent VPN connection from the second server to the primary. Using a custom setting RRAS profile, we have successfully managed to set up a site-to-site VPN connection so that from the second server itself, it can access any of the devices in the main office and communicate back. However, any connected machines in the second office cannot use this connection, even when using the second server as gateway. The demand-dial interface is setup from the Second Server dialing into Main Server and a static route set up on RRAS for 192.168.0.0 with subnet mask 255.255.0.0 pointing down this network interface. The main office has the network of 192.168.0.0/16 (subnet mask 255.255.0.0). The second office has the network of 172.16.100.0/24 (subnet mask 255.255.255.0). What steps do we need to take to ensure traffic from the second office PCs going towards 192.168.x.x addresses use the VPN route? Many Thanks in advance for any help the community can offer. Debug Information Here is the route print output from the second server: =========================================================================== Interface List 23...........................Main Office 22...........................RAS (Dial In) Interface 16...e0 db 55 12 fa 02 ......Local Area Connection - Virtual Network 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 14...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 24...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.16.100.250 172.16.100.222 261 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 <MAIN OFFICE IP> 255.255.255.255 172.16.100.250 172.16.100.222 6 172.16.100.0 255.255.255.0 On-link 172.16.100.222 261 172.16.100.113 255.255.255.255 On-link 172.16.100.113 306 172.16.100.222 255.255.255.255 On-link 172.16.100.222 261 172.16.100.223 255.255.255.255 On-link 172.16.100.222 261 172.16.100.224 255.255.255.255 On-link 172.16.100.222 261 172.16.100.225 255.255.255.255 On-link 172.16.100.222 261 172.16.100.226 255.255.255.255 On-link 172.16.100.222 261 172.16.100.227 255.255.255.255 On-link 172.16.100.222 261 172.16.100.228 255.255.255.255 On-link 172.16.100.222 261 172.16.100.229 255.255.255.255 On-link 172.16.100.222 261 172.16.100.230 255.255.255.255 On-link 172.16.100.222 261 172.16.100.255 255.255.255.255 On-link 172.16.100.222 261 192.168.0.0 255.255.0.0 192.168.101.87 192.168.101.17 266 192.168.101.17 255.255.255.255 On-link 192.168.101.17 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.16.100.222 261 224.0.0.0 240.0.0.0 On-link 172.16.100.113 306 224.0.0.0 240.0.0.0 On-link 192.168.101.17 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 172.16.100.222 261 255.255.255.255 255.255.255.255 On-link 172.16.100.113 306 255.255.255.255 255.255.255.255 On-link 192.168.101.17 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.0.200 Default 0.0.0.0 0.0.0.0 172.16.100.250 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 16 261 fe80::/64 On-link 16 261 fe80::edf4:85c6:3c15:dcbe/128 On-link 1 306 ff00::/8 On-link 16 261 ff00::/8 On-link 22 306 ff00::/8 On-link =========================================================================== Persistent Routes: None And here is the route print from one of the second office PCs: =========================================================================== Interface List 11...10 78 d2 32 53 27 ......Atheros AR8151 PCI-E Gigabit Ethernet Controller 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.16.100.250 172.16.100.103 10 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 172.16.100.0 255.255.255.0 On-link 172.16.100.103 266 172.16.100.103 255.255.255.255 On-link 172.16.100.103 266 172.16.100.255 255.255.255.255 On-link 172.16.100.103 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.16.100.103 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 172.16.100.103 266 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 11 266 fe80::/64 On-link 11 266 fe80::e973:de17:a045:aa78/128 On-link 1 306 ff00::/8 On-link 11 266 ff00::/8 On-link =========================================================================== Persistent Routes: None

  Read the article

• How to share internet over VPN and inside a virtual machine (Windows)?

  - by mountrix

  ` My final goal is to have a virtual machine at work in which anything that happen inside (tcp, udp, ping, ...) will use the Internet connection of a computer at home. So, if inside this VM should I open an Internet browser to a site such as "show my IP", my home IP should be printed. I am also looking for a way to debug/develop a software inside this VM, but I would like to tunnel only the connections of this software, not the full graphical interface, this is why a Remote Desktop solution won't fit me. The connection between the both computer should be secured somehow, like in a SSH tunnel. This ultimately should allow me to have a portable VM in which I can connect to whatever networks I have access at home, in a secure way. This is my configuration: At work, I have a LAN-connected desktop computer, with Windows 7 Professional Edition as a host [computer W] On this same computer, I have a Virtual Box machine running Windows XP [computer V] At home, I have a laptop computer, running Windows 7 Home Edition [computer H] This laptop is connected to a Livebox 2 broadband modem by Wifi. What I am trying to do is to sit at work in front of the virtual machine [V], and connect to a webpage as if the request was issued from the laptop [H] at home, and the data should be securely tunneled between the both. But if I am using internet directly inside [W], it should use the normal LAN interface at work. To achieve my goal, I first try using VPN, than SSH tunneling, without success. I first tried to install Teamviewer between [W] and [H]. This is working fine, I can send files, share desktop, etc. Teamviewer has a VPN mode that creates a new VPN network interface with its own IP, both on computer [W] and [H]. This allowed me to connect [H] as a network computer inside [W] and I was able to share files, but not to share Internet. At this point, I tried to use from [W] the Internet as if I was at home. I setup a route (using route add from command line in [W]) in order to instruct each packet going to a given website to pass by the new VPN interface on [W], with the hope it will be forwarded to [H], but the webpage was simply inaccessible. I then tried to setup a Windows VPN connection between [W] and [H], using the Windows 7 VPN feature. [H] was the server and [W] the client. But it failed: I got the "Unable to join a remote PC while trying to VPN" 720 Error when I was setting up the client on [W]. I think the problem is the Livebox 2 that could blocks the packets. But I am not sure of this: 1) with Teamviewer it works fine, 2) Livebox 2 has a configuration page for port mapping that gives the proper configuration to map VPN ports as an example so I guess that it should allow it, 3) I opened the ports 1723 (TCP) and 500 (UDP) according to some forums. Virtual box has a network configuration parameter in which I can use the VPN network interface created by Teamviewer as a bridged connection. This is suppose to work in the sense that all packets issued by the virtual machine [V] is supposed to go directly to [H]. But I had no internet connection inside [V]. Using the NAT mode, [V] has internet. For me this is the feature that I look for: filtering all connections from the virtual box application to the VPN network interface, and the remaining should use the normal LAN interface. Apart from the build-in feature of VBox, I even do not know if it is possible to route the packet from a given application to a given interface. Finally I tried also SSH tunneling, but this is not the solution I looked for. Using an external SSH server (Linux), I was able to create a localhost connection on [W] (or [V]), using something like 'ssh -N -D server[H]' in order to allow a web browser located in [W] to connect to any website using the SOCKS 5 proxy created locally (SOCKS is a build-in feature of SSH). But repeating the same operation on windows, using a windows SSH server inside [W] (I tried freeSSHd), it failed: SFTP worked, but not the SOCKS tunneling, it was like the browser in [H] did not find internet. Finally only Teamviewer looked able to create a VPN between [W] and [H], but I am not able to use it, as I want, I mean using the Internet connection of [H] sitting in front of [W]. I also tried to bridge the VPN interface and the wifi interface inside [H], but it blocked my laptop, and I tried also the Internet Connection Sharing, trying to share on [H] the wifi connection over the VPN interface. This fails also, but it seems because Teamviewer actually use the wifi interface to be able to provide the VPN link, so I guess I am creating a recursive loop. I do not know what to try next... Thank you for any advice!!

  Read the article

• squid3 auth thru samba using ntlm to AD doesn't work

  - by derty

  some users here are spending to much time exploring the WWW. So big boss whats to get this under control. We use a squid3 just for some security reason and chace benefits. and now i'm trying to set up a new proxy on a different server (Debian 6) Permissions are defined in AC and the squid3 should get the auth thru samba/winbind by using the ntlm protocol. but i'll get all the time Access, denited. it only works by using LDAP but thats not the way i need it. here some log and confs squid access.log 1326878095.784 1 192.168.15.27 TCP_DENIED/407 4049 GET http://at.msn.com/? -NONE/- text/html 1326878095.791 1 192.168.15.27 TCP_DENIED/407 4294 GET http://at.msn.com/? - NONE/- text/html 1326878095.803 9 192.168.15.27 TCP_DENIED/403 4028 GET http://at.msn.com/? kavan NONE/- text/html 1326878095.848 0 192.168.15.27 TCP_DENIED/403 3881 GET http://www.squid-cache.org/Artwork/SN.png kavan NONE/- text/html 1326878100.279 0 192.168.15.27 TCP_DENIED/403 3735 GET http://www.google.at/ kavan NONE/- text/html 1326878100.296 0 192.168.15.27 TCP_DENIED/403 3870 GET http://www.squid-cache.org/Artwork/SN.png kavan NONE/- text/html 1326878155.700 0 192.168.15.27 TCP_DENIED/407 4072 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml - NONE/- text/html 1326878155.705 2 192.168.15.27 TCP_DENIED/407 4317 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml - NONE/- text/html 1326878155.709 3 192.168.15.27 TCP_DENIED/403 4026 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml kavan NONE/- text/html squid chace 2012/01/18 10:12:49| Creating Swap Directories 2012/01/18 10:12:49| Starting Squid Cache version 3.1.6 for x86_64-pc-linux-gnu... 2012/01/18 10:12:49| Process ID 17236 2012/01/18 10:12:49| With 65535 file descriptors available 2012/01/18 10:12:49| Initializing IP Cache... 2012/01/18 10:12:49| DNS Socket created at [::], FD 7 2012/01/18 10:12:49| DNS Socket created at 0.0.0.0, FD 8 2012/01/18 10:12:49| Adding nameserver 192.168.15.2 from /etc/resolv.conf 2012/01/18 10:12:49| Adding nameserver 192.168.15.19 from /etc/resolv.conf 2012/01/18 10:12:49| Adding nameserver 192.168.15.1 from /etc/resolv.conf 2012/01/18 10:12:49| Adding domain schoenbrunn.local from /etc/resolv.conf 2012/01/18 10:12:49| helperOpenServers: Starting 5/5 'squid_ldap_auth' processes 2012/01/18 10:12:49| helperOpenServers: Starting 10/10 'ntlm_auth' processes 2012/01/18 10:12:49| helperOpenServers: Starting 10/10 'squid_kerb_auth' processes 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| helperOpenServers: Starting 5/5 'squid_ldap_group' processes 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| Unlinkd pipe opened on FD 73 2012/01/18 10:12:49| Local cache digest enabled; rebuild/rewrite every 3600/3600 sec 2012/01/18 10:12:49| Store logging disabled 2012/01/18 10:12:49| Swap maxSize 0 + 262144 KB, estimated 20164 objects 2012/01/18 10:12:49| Target number of buckets: 1008 2012/01/18 10:12:49| Using 8192 Store buckets 2012/01/18 10:12:49| Max Mem size: 262144 KB 2012/01/18 10:12:49| Max Swap size: 0 KB 2012/01/18 10:12:49| Using Least Load store dir selection 2012/01/18 10:12:49| Set Current Directory to /var/spool/squid3 2012/01/18 10:12:49| Loaded Icons. 2012/01/18 10:12:49| Accepting HTTP connections at [::]:3128, FD 74. 2012/01/18 10:12:49| HTCP Disabled. 2012/01/18 10:12:49| Squid modules loaded: 0 2012/01/18 10:12:49| Adaptation support is off. 2012/01/18 10:12:49| Ready to serve requests. 2012/01/18 10:12:50| storeLateRelease: released 0 objects smb.conf # Domain Authntication Settings workgroup = <WORKGROUP> security = ads password server = <DOMAINNAME>.LOCAL realm = <DOMAINNAME>.LOCAL ldap ssl = no # logging log level = 5 max log size = 50 # logs split per machine log file = /var/log/samba/%m.log # max 50KB per log file, then rotate ; max log size = 50 # User settings username map = /etc/samba/smbusers idmap uid = 10000-20000000 idmap gid = 10000-20000000 idmap backend = ad ; template primary group = <ad group> template shell = /sbin/nologin # Winbind Settings winbind separator = + winbind enum users = Yes winbind enum groups = Yes winbind netsted groups = Yes winbind nested groups = Yes winbind cache time = 10 winbind use default domain = Yes #Other Globals unix charset = LOCALE server string = <SERVERNAME> load printers = no printing = cups cups options = raw ; printcap name = /etc/printcap #obtain list of printers automatically on SystemV ; printcap name = lpstat ; printing = cups squid.conf auth_param ntlm program /usr/bin/ntlm_auth --require-membership-of=<DOMAINNAME>\\INTERNETZ --helper-protocol=squid-2.5-ntlmssp auth_param ntlm children 10 auth_param basic program /usr/lib/squid3/squid_ldap_auth -R -b "dc=<dcname>,dc=local" -D "cn=administrator,cn=Users,dc=<domainname>,dc=local" -w "******" -f sAMAccountName=%s -h 192.168.15.19:3268 auth_param basic realm "Proxy Authentifizierung. Bitte geben Sie Ihren Benutzername und Ihr Passwort ein!" #means insert you PW in an other language - # external_acl_type InetGroup %LOGIN /usr/lib/squid3/squid_ldap_group -R -b "dc=<domainname>,dc=local" -D "cn=administrator,cn=Users,dc=<domainname>,dc=local" -w "******" -f "(&(objectclass=person)(sAMAccountName=%v) (memberof=cn=%a,cn=internetz,dc=<domainname>,dc=local))" -h 192.168.15.19:3268 auth_param negotiate program /usr/lib/squid3/squid_kerb_auth -d auth_param negotiate children 10 auth_param negotiate keep_alive on acl localnet proxy_auth REQUIRED acl InetAccess external InetGroup Internetz http_access allow InetAccess http_access deny all acl auth proxy_auth REQUIRED http_access allow auth and a very suspicious is that by adding the proxy server to the Domain i see 2 new entries in the PC one with the original computer-name leopoldine and one with leopoldine CNF:f8efa4c4-ff0e-4217-939d-f1523b43464d ?!? I tried a lot, really... but i stuck on this problem... i actually i even reinstalled all dependent programs and reconfigured them from default. Group exists and has me in it. Firefox running on the old proxy and i use IE for testing the new one. But i'll get all the time Access-Denited and to be honest i'm quite a beginner, so please don't be to prude. I'll interested in improving, i'll get the information we need to fix this but i started working 2 month ago and got only 1 1/2 year's training and not a single sec. in linux ;)

  Read the article

• Performance required to improve Windows Experience Index?

  - by Ian Boyd

  Is there a guide on the metrics required to obtain a certain Windows Experience Index? A Microsoft guy said in January 2009: On the matter of transparency, it is indeed our plan to disclose in great detail how the scores are calculated, what the tests attempt to measure, why, and how they map to realistic scenarios and usage patterns. Has that amount of transparency happened? Is there a technet article somewhere? If my score was limited by my Memory subscore of 5.9. A nieve person would suggest: Buy a faster RAM Which is wrong of course. From the Windows help: If your computer has a 64-bit central processing unit (CPU) and 4 gigabytes (GB) or less random access memory (RAM), then the Memory (RAM) subscore for your computer will have a maximum of 5.9. You can buy the fastest, overclocked, liquid-cooled, DDR5 RAM on the planet; you'll still have a maximum Memory subscore of 5.9. So in general the knee-jerk advice "buy better stuff" is not helpful. What i am looking for is attributes required to achieve a certain score, or move beyond a current limitation. The information i've been able to compile so far, chiefly from 3 Windows blog entries, and an article: Memory subscore Score Conditions ======= ================================ 1.0 < 256 MB 2.0 < 500 MB 2.9 <= 512 MB 3.5 < 704 MB 3.9 < 944 MB 4.5 <= 1.5 GB 5.9 < 4.0GB-64MB on a 64-bit OS Windows Vista highest score 7.9 Windows 7 highest score Graphics Subscore Score Conditions ======= ====================== 1.0 doesn't support DX9 1.9 doesn't support WDDM 4.9 does not support Pixel Shader 3.0 5.9 doesn't support DX10 or WDDM1.1 Windows Vista highest score 7.9 Windows 7 highest score Gaming graphics subscore Score Result ======= ============================= 1.0 doesn't support D3D 2.0 supports D3D9, DX9 and WDDM 5.9 doesn't support DX10 or WDDM1.1 Windows Vista highest score 6.0-6.9 good framerates (e.g. 40-50fps) at normal resoltuions (e.g. 1280x1024) 7.0-7.9 even higher framerates at even higher resolutions 7.9 Windows 7 highest score Processor subscore Score Conditions ======= ========================================================================== 5.9 Windows Vista highest score 6.0-6.9 many quad core processors will be able to score in the high 6 low 7 ranges 7.0+ many quad core processors will be able to score in the high 6 low 7 ranges 7.9 8-core systems will be able to approach 8.9 Windows 7 highest score Primary hard disk subscore (note) Score Conditions ======= ======================================== 1.9 Limit for pathological drives that stop responding when pending writes 2.0 Limit for pathological drives that stop responding when pending writes 2.9 Limit for pathological drives that stop responding when pending writes 3.0 Limit for pathological drives that stop responding when pending writes 5.9 highest you're likely to see without SSD Windows Vista highest score 7.9 Windows 7 highest score Bonus Chatter You can find your WEI detailed test results in: C:\Windows\Performance\WinSAT\DataStore e.g. 2011-11-06 01.00.19.482 Disk.Assessment (Recent).WinSAT.xml <WinSAT> <WinSPR> <DiskScore>5.9</DiskScore> </WinSPR> <Metrics> <DiskMetrics> <AvgThroughput units="MB/s" score="6.4" ioSize="65536" kind="Sequential Read">89.95188</AvgThroughput> <AvgThroughput units="MB/s" score="4.0" ioSize="16384" kind="Random Read">1.58000</AvgThroughput> <Responsiveness Reason="UnableToAssess" Kind="Cap">TRUE</Responsiveness> </DiskMetrics> </Metrics> </WinSAT> Pre-emptive snarky comment: "WEI is useless, it has no relation to reality" Fine, how do i increase my hard-drive's random I/O throughput? Update - Amount of memory limits rating Some people don't believe Microsoft's statement that having less than 4GB of RAM on a 64-bit edition of Windows doesn't limit the rating to 5.9: And from xxx.Formal.Assessment (Recent).WinSAT.xml: <WinSPR> <LimitsApplied> <MemoryScore> <LimitApplied Friendly="Physical memory available to the OS is less than 4.0GB-64MB on a 64-bit OS : limit mem score to 5.9" Relation="LT">4227858432</LimitApplied> </MemoryScore> </LimitsApplied> </WinSPR> References Windows Vista Team Blog: Windows Experience Index: An In-Depth Look Understand and improve your computer's performance in Windows Vista Engineering Windows 7 Blog: Engineering the Windows 7 “Windows Experience Index”

  Read the article

• How to set up port forwarding and firewall settings for torrents using Transmsission on Mac OSX 10.5

  - by Liz

  I have picked up bits of advice here and there on the internet and got someway through this tortuous exercise (after it took 18 hours to download the first torrent I tried yesterday - magnet-link for a film). Where I have got stuck is with configuring the firewall on the Netgear Router but I am not sure if I have caused the problem myself by something else I have done configuring the Mac System Preferences for Security or Networking. I have been following the sections of these instructions that seem to apply, although they are written for a different OSX version (don't know which one, but the screen shots do not match what I see) and I am not wanting to set up my Mac as a server and attending to the parts that apply to port forwarding for Netgear rather than LinkSys: http://homepage.mac.com/car1son/static_port_fwd_intro.html I have been trying to follow these instructions: Instructions for DG834, DG834G, DG824M, FR114W, FM114P, FR114P, FR328S, FVL328, FVS328, FVS338, FVX538, FWAG114, FWG114P, or FVS318v3 These routers do port forwarding by assigning port numbers to a "service" associated with the application you want to run. "Rules" are set for particular services. Rules block or allow access, based on various conditions such as the time of day and the name of the service. To Create a New Inbound or Outbound Rule 1. Submit the router's address in an Internet browser. (The default is 192.168.0.1). 2. Enter the router's username and password. 3. From the main menu, click Security > Rules. 4. Click Add for inbound or outbound traffic, as appropriate to the application you are planning to run. 5. Select the Service. The services the router knows about are listed in the drop down. If the service you want is not listed, add it as described in the next section. 6. Select the Action, for example ALLOW always. 7. For Send to LAN Server, enter the IP address of the local server. Note that this is also the IP address the computers on your LAN will access. 8. For WAN User choose Any, or limit access to particular IP addresses. 9. For Log selection it is reasonable to turn logs on, especially at the beginning when you are unsure of the result of the changes you are making. Later, you may want to set logs to "Never" for performance reasons. 10. Click Apply. As noted in user manual for some models: * Consider using the Dynamic DNS feature on the Advanced menu, so that external users can find your network when the DHCP lease is renewed by your ISP. * If your own LAN server uses DHCP, and your IPs change on rebooting, consider using the Reserved IP Address feature in the LAN IP menu. To Add a Service for These Routers 1. Click Security > Services > Add Custom Service. 2. Enter any name you choose for the service. 3. Select whether the service is to use TCP or UDP. If you are unsure, select both. 4. Enter the lowest port number used by the service. 5. Enter the highest port number used. If the service uses only one port number, enter the same number. 6. Click Apply. There is no "Security - Rules" submenu in the Netgear page, so I have been trying to access "Security - Firewall Rules". I can access everthing else in the Netgear settings as Admin but I cannot get the "Firewall Rules" section to open up. (I am not 100% sure I will know exactly what to do if and when I do get it opened up!) I haven't managed to find though searching the internet any instructions that would seem to apply specifically to what I am trying to achieve, so would be very grateful if someone could either point me in the right direction or give me some advice directly. Best wishes, Liz

  Read the article

• OSX Server 3, Mac clients binding to OD and Profile Manager failing

  - by dbf

  I've made a setup containing a Mac Mini with OSX Server 3 (Mavericks 10.9.2) using Open Directory and Profile Manager (Mail, etc all set up and working). Now the thing is, internally on the local network, everything works great. Clients can bind to the OD and the users are able to login. I can install trust and settings profiles (either custom or group profiles) and all services in the profiles mentioned are being configured correctly. I can log in and out, hump around and do it a 100 times on different macs with different users, it works. My goal is to make this service publicly. The domain is with a FQDN which I own, for simplicity let's say server.domain.com. Now the only way for me to bind the clients to the OD is using LDAP mapping RCF2307 (without SSL) and a DN suffix of dc=server,dc=domain,dc=com using the Directory Utility. The options from server, or open directory will throw several errors like Connection failed to node '/LDAPv3/server.domain.com (2100). First of all I don't really understand the problem why clients can't bind to the OD like it does locally, with and without SSL (all ports are open, literally all ports are open, not just 389,636 and 1640, wasn't sure if I was missing any). When the clients are using LDAP mapping RFC2307 to bind (without SSL only), clients are able to authenticate, login and even load the Trust profile. But every Settings profile will fail with a Debug Message: Unable to find GUID in user record OD or fail to install saying missing user identification. Is there any way to get this to work without RFC2307? Because there is quite some stuff missing when using RFC2307 and not pull the mapping from the server or use open directory. Is this setup even possible? Or should I use VPN to authenticate with the OD? The network setup is a Modem/Router (DHCP off) with WAN NATted to an Airport Extreme (Using DHCP+NAT). The AE does notify with a double NAT message but I haven't had any problems with it on any other service. So WAN - 192.168.2.220 (static), AE - 10.0.1.* (dhcp) Output of DIG from the outside using dig server.domain.com ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;server.domain.com. IN A ;; ANSWER SECTION: server.domain.com. 77 IN A 91.50.*.* (valid WAN IP) ;; SERVER 172.*.*.1#53(172.*.*.1) (iPhone) DIG locally from a client and server (same output) ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 2, ADDITIONAL: 0 ;; QUESTION SECTION: ;server.domain.com. IN A ;; ANSWER SECTION: server.domain.com. 10800 IN A 10.0.1.11 ;; AUTHORITY SECTION: server.domain.com. 10800 IN NS domain.com. (used for email send in relay) server.domain.com. 10800 IN NS server.domain.com. ;; SERVER 10.0.1.11#53(10.0.1.11) Are there any things I should check? Only have OSX. -- double NAT issue, plugged in the server directly on the Modem/Router with a static IP and issue remains. Guess that rules out the double NAT thing. -- changeip -checkhostname comes with There is nothing to change, e.g. success. Primary address = 10.0.1.11 Current HostName = server.domain.com DNS HostName = server.domain.com For now, I've made a workaround by using an admin account that forces a permanent VPN connection on boot. That means before it comes to the login, a connection is already made or underway. I will continue this post when I have more time, also locating all the necessary .log files of each application involved. I have some suspicions but have to debug a bit more when I have more time on my hands .. Unless, of course, I get sidetracked with having a life. Which is arguably not very likely. krypted.com

  Read the article

• Mount TMPFS instead of ro /dev

  - by schiggn

  I am working on a ARM-Based embedded system with a custom Debian Linux based on kernel 2.6.31. In the final system, the Root file system is stored as squashfs on flash. Now, the folder /dev is created by udev, but since there is no hot plugging functionality needed and booting time is critical, I wanted to delete udev and "hard code" the /dev folder (read here, page 5). because i still need to change parameters of the devices (with ioctl /sysfs) this does not work for me in this case. so i thought of mounting a tmpfs on /dev and change the parameters there. is this possible? and how to do best? my approach would be: delete /dev from RFS create tar containing basic devices mount tmpfs /dev untar tar-file into /dev change parameters Could this work? Do you see any problems? I found out, that you can mount on top of already mounted mount point, is it somehow possible just to take data with while mounting the new file system? if so that would be very convenient! Thanks Update: I just tried that out, but I'm stuck at a certain point. I packed all my devices into devices.tar, packed it into /usr of my squashfs and added the following lines to mountkernfs.sh, which is executed right after INIT. #mount /dev on tmpfs echo -n "Mounting /dev on tmpfs..." mount -o size=5M,mode=0755 -t tmpfs tmpfs /dev mknod -m 600 /dev/console c 5 1 mknod -m 600 /dev/null c 1 3 echo "done." echo -n "Populating /dev..." tar -xf /usr/devices.tar -C /dev echo "done." This works fine on the version over NFS, if I place printf's in the code, I can see it executing, if I comment out the extracting part, its complaining about missing devices. Booting OK mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 IP-Config: Unable to set interface netmask (-22). Looking up port of RPC 100003/2 on 192.168.1.234 Looking up port of RPC 100005/1 on 192.168.1.234 VFS: Mounted root (nfs filesystem) on device 0:14. Freeing init memory: 136K INIT: version 2.86 booting Mounting /dev on tmpfs...done. Populating /dev...done. Initializing /var...done. Setting the system clock. System Clock set to: Thu Sep 13 11:26:23 UTC 2012. INIT: Entering runlevel: 2 UBI: attaching mtd8 to ubi0 Commenting out the extraction of the tar mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 IP-Config: Unable to set interface netmask (-22). Looking up port of RPC 100003/2 on 192.168.1.234 Looking up port of RPC 100005/1 on 192.168.1.234 VFS: Mounted root (nfs filesystem) on device 0:14. Freeing init memory: 136K INIT: version 2.86 booting Mounting /dev on tmpfs...done. Populating /dev...done. Initializing /var...done. Setting the system clock. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Unable to set System Clock to: Thu Sep 13 12:24:00 UTC 2012 ... (warning). INIT: Entering runlevel: 2 libubi: error!: cannot open "/dev/ubi_ctrl" So far so good. But if I pack the whole story into a squashfs and boot from there, it is acting strange. It's telling me while booting that it is unable to open an initial console and its throwing errors on mounting the UBIFS devices, but finally provides a login anyway. Over that my echo's are not executed. If I then log in, /dev is mounted as TMPFS as desired and all the devices reside inside. When I redo the "mount" command to mount the UBIFS partitions it is executed whitout problem and useable. From squashfs VFS: Mounted root (squashfs filesystem) readonly on device 31:15. Freeing init memory: 136K Warning: unable to open an initial console. mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 UBIFS error (pid 484): ubifs_get_sb: cannot open "ubi1_0", error -19 Additionally, a part of the rest of the bootscripts is still exexuted, but not all of them. Does anyone has a clue why? Other question, is 5MB enough/too much for /dev?

  Read the article

• Deployment Workbench no longer available after PXE boot

  - by Patrick

  Our build process revolves around windows Deployment Workbench. Unfortunately this was setup by someone who is no longer with the company, and no-one has ever dared/needed to make any changes. The other day it stopped working. It turns out that one of our build guys started thinking about changing some stuff in it, clicked something and now it no longer works (He is saying now that he right clicked on the 'LAB' entry in 'Deployment points' and hit 'Update', which took some time to run through apparently). The job has fallen on me to resolve and frankly I'm not sure what I'm doing. I was wondering if someone with more experience than me can provide some pointers as to troubleshooting cos I'm feeling quite a lot in the dark here. On the server I have Deployment Workbench up and running (MMC snapin) version 3.0. There is a WDS service that appears to be running ok, as does the tFTPd service. Nothing specific to this in event logs. From the client side; PXE boot works and gets you to the Win PE launch, and it has the correct company logo as the background (proving to me that its loading win PE from the network). WPEINIT runs, and asks for domain credentials, here the team simply put User/Pass/Domain in the boxes and click ok. Normally the build would kick off. Instead they get an error message saying that the \NATBLU01\Distribution$ share isn't available. Checking \NATBLU01\Distribution$ shows that its there and accessible over the network. Security/permissions seem ok, even 'ANONYMOUS LOGON' has read access to that share so I don't see that being a problem. Digging the trace files from C:\MININT\SMSOSD\OSDLOGS\ after an attempt to run the build I can see an error saying much the same - <![LOG[Validating connection to \\NATBLU01\Distribution$]LOG]!><time="16:42:14.000+000" date="03-15-2012" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[FindFile: The file OSDConnectToUNC.exe could not be found in any standard locations.]LOG]!><time="16:42:14.000+000" date="03-15-2012" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[The network location cannot be reached. For information about network troubleshooting, see Windows Help.]LOG]!><time="16:42:24.000+000" date="03-15-2012" component="LiteTouch" context="" type="3" thread="" file="LiteTouch"> <![LOG[ERROR - Unable to map a network drive to \\NATBLU01\Distribution$.]LOG]!><time="16:42:24.000+000" date="03-15-2012" component="LiteTouch" context="" type="3" thread="" file="LiteTouch"> BDD.LOG shows much the same. Full copies of the .LOG files can both files be found here : BDD.LOG LITETOUCH.LOG I can get to a command prompt from the Win PE that boots from PXE, however there isn't any network stuff there. IPCONFIG returns nothing so none of the tests I would usually run resolve anything. I'm at a loss frankly. I did wonder if I could perhaps start a new build process but if the change to the DeploymentWorkbench has knocked it offline I don't think I'm going to be able to create a new deployment. Failing that; we do have a deployment point labeled type 'Media' which appears to be a DVD ISO image of one of the builds, but its dated 2008, is it possible to export the network build to .ISO and build from DVD? We are looking at new hardware to run this from anyway (for the impending Windows 7 roll out) so a temporary work round isn't going to be too much of a problem. All assistance is appreciated! EDIT : OK. Got it working again. Solution was close to Newmanth's idea. The problem was that our PE image didn't appear to be connecting the network. I had an older copy of the PE boot.WIM on a stick that I had been using for other purposes. I booted that and correctly got a network connection. Showed a correct internal IP and could ping out etc etc. However I was still getting the same errors in all the logs and in when wpeinit was running. What I did seperately was to update the PE image that DeploymentWorkbench was pushing out to display a different back ground. I wanted to prove that I was working in the correct place. Turns out that I wasn't. I went and looked at the other deployment stuff we had on this machine, Windows Deployment Services was installed and although all the install images are off line the boot image was online, so I uploaded the copy from my stick to that. Booted straight off. And fixed. Working. Yay! For anyone stumbling across this in the future you may find that although your deployment images are located in the DeploymentWorkbench, the Win PE boot image you are launching from is located in the associated Windows Deployment Services images.

  Read the article

• Linux Kernel crash mutex_lock_slowpath "blocked for more than 120 seconds". What to do?

  - by Roddick

  I have out-of-the box Debian Lenny with non-custom kernel 2.6.26-2-amd64. Brand new server that is used to 5% of it's potential, CPU and Disk-wise. Meaning it probably not crashing because of overload. every few days it freezes with hundreds of these messages in console log: : [284847.828428] INFO: task apache2:12473 blocked for more than 120 seconds. : [284847.868468] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. : [284847.912759] apache2 D ffff8101bc6b7ab0 0 12473 14358 : [284847.912763] ffff810160d5bc50 0000000000000082 ffff8101c0002e40 0000000000000000 : [284847.912766] ffff8101a7c42950 ffff810327d92810 ffff8101a7c42bd8 0000000400000044 : [284847.912770] ffff8101c0002e40 00000000000612d0 0000000000000000 00000040000612d0 : [284847.912773] Call Trace: : [284847.912786] [<ffffffff80429b0d>] __mutex_lock_slowpath+0x64/0x9b : [284847.912790] [<ffffffff80429972>] mutex_lock+0xa/0xb : [284847.912794] [<ffffffff802a20b9>] do_lookup+0x82/0x1c1 : [284847.912800] [<ffffffff802a4271>] __link_path_walk+0x87a/0xd19 : [284847.912805] [<ffffffff80295844>] kmem_getpages+0x96/0x15f : [284847.912808] [<ffffffff80295fb7>] ____cache_alloc_node+0x6d/0x106 : [284847.912814] [<ffffffff802a4756>] path_walk+0x46/0x8b : [284847.912819] [<ffffffff802a4a82>] do_path_lookup+0x158/0x1cf : [284847.912822] [<ffffffff802a3879>] getname+0x140/0x1a7 : [284847.912827] [<ffffffff802a53f1>] __user_walk_fd+0x37/0x4c : [284847.912831] [<ffffffff8029e381>] vfs_lstat_fd+0x18/0x47 : [284847.912840] [<ffffffff8029e3c9>] sys_newlstat+0x19/0x31 : [284847.912848] [<ffffffff8020beda>] system_call_after_swapgs+0x8a/0x8f Almost all traces has __mutex_lock_slowpath as top-level. Only some has different trace: : [284847.737386] INFO: task apache2:12472 blocked for more than 120 seconds. : [284847.777551] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. : [284847.824881] apache2 D ffff8101bc6b7ab0 0 12472 14358 : [284847.824886] ffff8101b9cc1c50 0000000000000086 ffffffffa0131e0a 0000000000000002 : [284847.824889] ffff8102e7454300 ffff810324c6cad0 ffff8102e7454588 0000000000000000 : [284847.824893] 0000000000000001 0000000000000296 0000000000000003 ffff8101b9cc1c58 : [284847.824896] Call Trace: : [284847.828403] [<ffffffffa0131e0a>] :ext3:__ext3_journal_dirty_metadata+0x1e/0x46 : [284847.828412] [<ffffffff80429b0d>] __mutex_lock_slowpath+0x64/0x9b : [284847.828418] [<ffffffff80429972>] mutex_lock+0xa/0xb : [284847.828421] [<ffffffff802a20b9>] do_lookup+0x82/0x1c1 : [284847.828427] [<ffffffff802a4271>] __link_path_walk+0x87a/0xd19 : [284847.828428] [<ffffffff80271296>] find_lock_page+0x1f/0x8a : [284847.828428] [<ffffffff80273182>] filemap_fault+0x1c2/0x33c : [284847.828428] [<ffffffff802a4756>] path_walk+0x46/0x8b : [284847.828428] [<ffffffff802a4a82>] do_path_lookup+0x158/0x1cf : [284847.828428] [<ffffffff802a3879>] getname+0x140/0x1a7 : [284847.828428] [<ffffffff802a53f1>] __user_walk_fd+0x37/0x4c : [284847.828428] [<ffffffff8029e381>] vfs_lstat_fd+0x18/0x47 : [284847.828428] [<ffffffff8029e3c9>] sys_newlstat+0x19/0x31 : [284847.828428] [<ffffffff8020beda>] system_call_after_swapgs+0x8a/0x8f kernel: [1912668.466347] INFO: task apache2:17984 blocked for more than 120 seconds. [1912668.507035] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. : [1912668.555165] apache2 D ffff8101c5637ba0 0 17984 17282 : [1912668.596752] ffff810166a7dd30 0000000000000086 0000000000000000 ffff810166a7dcd8 : [1912668.643341] ffff8101c563c880 ffff81024505f000 0000000000000002 ffff810166a7dd68 : [1912668.699566] 0000000000000086 00000000000cb1a0 0000000000000000 ffff81017f344d60 : [1912668.744773] Call Trace: : [1912668.761754] [<ffffffff8022a3ed>] pick_next_task_fair+0x6e/0x7a : [1912668.829311] [<ffffffff802be0e2>] bio_alloc_bioset+0x89/0xd9 : [1912668.861930] [<ffffffff8024ac3a>] getnstimeofday+0x39/0x98 : [1912668.897005] [<ffffffff802710f6>] sync_page+0x0/0x41 : [1912668.927868] [<ffffffff80429487>] io_schedule+0x5c/0x9e : [1912668.960286] [<ffffffff80271132>] sync_page+0x3c/0x41 : [1912668.991756] [<ffffffff804295fa>] __wait_on_bit_lock+0x36/0x66 : [1912669.031757] [<ffffffff802710e3>] __lock_page+0x5e/0x64 : [1912669.064191] [<ffffffff802461d3>] wake_bit_function+0x0/0x23 : [1912669.100100] [<ffffffff80281bc5>] handle_mm_fault+0x5e4/0x8de : [1912669.134531] [<ffffffff802461a5>] autoremove_wake_function+0x0/0x2e : [1912669.174623] [<ffffffff802aa108>] fcntl_setlk+0x1cf/0x291 : [1912669.210623] [<ffffffff802461a5>] autoremove_wake_function+0x0/0x2e : [1912669.246923] [<ffffffff802a677f>] sys_fcntl+0x280/0x2f7 After googling for "mutex_lock_slowpath" I can only find the Kernel mailing list discussions that this issue was introduced in some commit. Wthout reference to verison. Discussions as recent as Jan 25, 2011. The Kernel I am using is form Debian Lenny, year ago. What should I do? Is this bug even fixed in kernel? if it's such obvious bug why it happens so rarely? Should I download latest kernel from kernel.org and upgrade? Should I use Debian backports to install new "Approved" kernel? Am I missing something? What to do?

  Read the article

• Cisco: unable to negotiate IP using IPCP with Windows server

  - by lnk

  I am connecting to Windows server using PPP (for vpn), I establish connection but server does not respond me for my address requests: *Mar 23 00:40:06.055: Vi1 MS-CHAP-V2: I CHALLENGE id 0 len 25 from "MSDC" *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using hostname from interface CHAP *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using password from interface CHAP *Mar 23 00:40:06.067: Vi1 MS-CHAP-V2: O RESPONSE id 0 len 69 from "XXX" *Mar 23 00:40:06.087: Vi1 PPP: I pkt type 0xC223, datagramsize 50 link[ppp] *Mar 23 00:40:06.087: Vi1 MS-CHAP-V2: I SUCCESS id 0 len 46 msg is "S=XXX" *Mar 23 00:40:06.087: Vi1 MS CHAP V2 No Password found for : XXX *Mar 23 00:40:06.091: Vi1 MS CHAP V2 Check AuthenticatorResponse Success for : XXX *Mar 23 00:40:06.091: Vi1 IPCP: O CONFREQ [Closed] id 1 len 20 *Mar 23 00:40:06.091: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:06.091: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:07.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up *Mar 23 00:40:07.091: Vi1 LCP: O ECHOREQ [Open] id 1 len 12 magic 0x194CAFCF *Mar 23 00:40:07.103: Vi1 LCP-FS: I ECHOREP [Open] id 1 len 12 magic 0x361B62E5 *Mar 23 00:40:07.103: Vi1 LCP-FS: Received id 1, sent id 1, line up *Mar 23 00:40:08.083: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:08.083: Vi1 IPCP: O CONFREQ [REQsent] id 2 len 20 *Mar 23 00:40:08.083: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:08.083: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:10.099: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:10.099: Vi1 IPCP: O CONFREQ [REQsent] id 3 len 20 *Mar 23 00:40:10.099: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:10.099: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.115: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:12.115: Vi1 IPCP: O CONFREQ [REQsent] id 4 len 20 *Mar 23 00:40:12.115: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:12.115: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.211: Vi1 LCP: O ECHOREQ [Open] id 2 len 12 magic 0x194CAFCF *Mar 23 00:40:12.219: Vi1 LCP-FS: I ECHOREP [Open] id 2 len 12 magic 0x361B62E5 *Mar 23 00:40:12.219: Vi1 LCP-FS: Received id 2, sent id 2, line up *Mar 23 00:40:14.131: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:14.131: Vi1 IPCP: O CONFREQ [REQsent] id 5 len 20 *Mar 23 00:40:14.131: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:14.131: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:16.147: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:16.147: Vi1 IPCP: O CONFREQ [REQsent] id 6 len 20 *Mar 23 00:40:16.147: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:16.147: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:17.331: Vi1 LCP: O ECHOREQ [Open] id 3 len 12 magic 0x194CAFCF *Mar 23 00:40:17.343: Vi1 LCP-FS: I ECHOREP [Open] id 3 len 12 magic 0x361B62E5 *Mar 23 00:40:17.343: Vi1 LCP-FS: Received id 3, sent id 3, line up You see: My router asks for address, but only keepalives are on line. But the same server works with windows client!! ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption service internal ! hostname Router ! boot-start-marker boot-end-marker ! ! no aaa new-model ! resource policy ! ip subnet-zero ! ! ip cef vpdn enable ! vpdn-group pptp request-dialin protocol pptp pool-member 1 initiate-to ip XXXX ! ! ! ! ! ! ! bridge irb ! ! interface ATM0 no ip address shutdown no atm ilmi-keepalive dsl operating-mode auto ! interface FastEthernet0 ! interface FastEthernet1 ! interface FastEthernet2 ! interface FastEthernet3 ! interface Dot11Radio0 no ip address shutdown speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Vlan1 no ip address bridge-group 1 ! interface Dialer0 ip address negotiated encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer string XXX dialer persistent dialer vpdn dialer-group 1 keepalive 5 3 no cdp enable ppp authentication ms-chap-v2 optional ppp eap refuse ppp chap hostname XXX ppp chap password 0 XXX ppp ipcp mask request ppp ipcp ignore-map ppp ipcp address accept ! interface BVI1 mac-address XXX.XXX.XXX ip address dhcp ! ip classless ip route 172.0.0.0 255.0.0.0 Dialer0 ! no ip http server no ip http secure-server ! dialer-list 1 protocol ip permit ! control-plane ! bridge 1 protocol vlan-bridge bridge 1 route ip ! line con 0 no modem enable line aux 0 line vty 0 4 login ! scheduler max-task-time 5000 end

  Read the article

• What needs updating when moving a bootable Windows 7 (or Vista) partition?

  - by SuperTempel

  When I move a bootable NTFS partition with Windows on it to a different block offset, what needs updating to make it bootable again? In particular, here's what I tried: I have a disk with several partitions, one of which is the NTFS partition with Windows on it, and the disk uses the plain old MBR block 0 for the partitions layout (no more than 4 partitions). Now I format and partition a new, larger, disk. There I make room for the NTFS partition and copy the contents from the old disk's NTFS Windows partition into. And I make the partition "active". However, when I try to boot from this disk, I get a "read error" message immediately and the booting stops, the exact text is: A disk read error occurred Press Ctrl+Alt+Del to restart I verified that both disks have the same boot sector code in block 0. It seems to me that something else might need updating. I guess that somewhere there's a absolute block reference that I need to update, probably pointing to the next level loader or to the NT kernel. Update: I found this article going quite into the depth of what I want to know. However, it says to modify boot.ini, but I have Windows 7 installed here, where such things appear to have changed: No boot.ini but a folder called System Volume Information with GUID and other data in it that sounds related to my problem. Going to keep digging... Update 2: Thanks to the terrible looking but very informative website by starman, I was able to figure out the first step: The NTFS boot sector has a field for "hidden" sectors. This feld has to contain the sector number of the boot sector. This solves the "read error" message. Now, however, I get a "BOOTMGR is missing" error instead. Looks like there's another place where a block number has to be adjusted, but I can't find anything in the code listing about this. I do find a lot of help sites suggesting Windows tools for fixing this "BOOTMGR is missing" problem, but none seem to know what goes on behind the scenes. Kind of like suggesting to re-install Windows when there's a little problem with it. At least, those fixes seem to work, mostly involving the Bcdedit and Bootrec tools. Now, who knows what they do, especially the latter, in regards to a moved partition? Update 3: After lots of trial-and-error attempts, I believe now that the solution lies in the BCD-Template registry file, residing usually inside \Windows\System32\config. If I get this updated using the "bcdboot" command, Windows starts up from it. I am now in the middle of figuring out what information this registry contains relevant to the above question. Any pointers to the contents of this registry are welcome. Update 4: Turns out that while the BCD-Template file gets rewritten and has different binary contents than its predecessor, the values inside do not change. So it must be something else that bcdboot.exe writes. I had previously already checked if it changes the first 32 boot blocks of the partition, but they appear to remain unchanged. Parititon map doesn't get changed, either. So what is it that bcdboot modifies besides the BCD registry? Any tips on how I can trace that? Are there low level tools that show me what files a program writes to? Update 5: The answer seems to be: c:\Boot\BCD is also changed, and that appears to be the key file for the boot manager's process. I'll investigate this later... Update 6: It seems to be an important detail that I had originally two partitions created when I installed Windows 7: A small partition of 204800 sectors which appears to be a bootstrap partition, followed by the actual, large, partition containing the Windows system (drive C:). When I tried to transfer this installation to a new, larger, disk, I had kept the same two partitions intact on the new drive, although they ended up at a different offset. This alone led to the "BOOTMGR is missing" message. Since then, I've used bcdboot.exe only on the Windows partition, which added the \Boot\BCD file on that partition. That file (and folder) did originally only exist on the smaller partition. Hence, this problem may be more complicated in my case as one partition (the boot strapper) referred to another partition (the one containing the OS), whereas other people may only have to deal with one partition containing both, and maybe there the solution is simpler. Update 7: Found one more detail: The \Boot\BCD file records the MBR's serial number. If that number doesn't match, the system won't boot. Next I'll test if there's also an absolute block reference stored in there.

  Read the article

• How to Edit or Add a New Row in jqGrid

  - by Paul

  My jqGrid that does a great job of pulling data from my database, but I'm having trouble understanding how the Add New Row functionality works. Right now, I'm able to edit inline data, but I'm not able to create a new row using the Modal Box. I'm missing that extra logic that says, "If this is a new row, post this to the server side URL" instead of modifying existing data. (Right now, hitting Submit only clears the form and reloads the grid data.) The documentation states that Add New Row is: jQuery("#editgrid").jqGrid('editGridRow',"new",{height:280,reloadAfterSubmit:false}); but I'm not sure how to use that correctly. I've spent alot of time studying the Demos, but they seem to all use an external button to fire the new row command, rather than using the Modal Form, which I want to do. My complete code is here: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en" lang="en"> <head> <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> <title>jqGrid</title> <link rel="stylesheet" type="text/css" media="screen" href="../css/ui-lightness/jquery-ui-1.7.2.custom.css" /> <link rel="stylesheet" type="text/css" media="screen" href="../css/ui.jqgrid.css" /> <script src="jquery-1.3.2.min.js" type="text/javascript"></script> <script src="../js/i18n/grid.locale-en.js" type="text/javascript"></script> <script src="jquery.jqGrid.min.js" type="text/javascript"></script> </head> <body> <h2>My Grid Data</h2> <table id="list" class="scroll"></table> <div id="pager" class="scroll c1"></div> <script type="text/javascript"> var lastSelectedId; jQuery('#list').jqGrid({ url:'grid.php', datatype: 'json', mtype: 'POST', colNames:['ID','Name', 'Price', 'Promotion'], colModel:[ {name:'product_id',index:'product_id', width:25,editable:false}, {name:'name',index:'name', width:50,editable:true, edittype:'text',editoptions:{size:30,maxlength:50}}, {name:'price',index:'price', width:50, align:'right',formatter:'currency', editable:true}, {name:'on_promotion',index:'on_promotion', width:50, formatter:'checkbox',editable:true, edittype:'checkbox'}], rowNum:10, rowList:[5,10,20,30], pager: $('#pager'), sortname: 'product_id', viewrecords: true, sortorder: "desc", caption:"Database", width:500, height:150, onSelectRow: function(id){ if(id && id!==lastSelectedId){ $('#list').restoreRow(lastSelectedId); $('#list').editRow(id,true,null,onSaveSuccess); lastSelectedId=id; }}, editurl:'grid.php?action=save'}) .jqGrid('navGrid','#pager', {refreshicon: 'ui-icon-refresh',view:true}, {height:280,reloadAfterSubmit:true}, {height:280,reloadAfterSubmit:true}, {reloadAfterSubmit:true}) .jqGrid('editGridRow',"new",{height:280,reloadAfterSubmit:false}); function onSaveSuccess(xhr) {response = xhr.responseText; if(response == 1) return true; return false;} </script></body></html> If it makes it easier, I'd be willing to scrap the inline editing functionality and do editing and posting via modal boxes. Any help would be greatly appreciated.

  Read the article

• jqgrid setting cutom formatter to dynamic column collection

  - by user312249

  I am using jqgrid. We are building a dashboard functionality with jquery. Different application just have to register respective application page and dashboard will render that page.To achieve this we are using jqgrid as one of the jquery plugin. Following is my codeenter code here var ph = '#' + placeHolder; var _prevSort; $.ajax({ url: dataUrl, dataType: "json", async: true, success: function(json) { pager = $('#' + pager); if (json.showPager === "false") { pager = eval(json.showPager); } dataUrl += "&jqSession=true"; $(ph).jqGrid({ url: dataUrl, datatype: "json", sortclass: "grid_sort", colNames: JSON.parse(json.colNames), colModel: JSON.parse(json.colModel), forceFit: true, rowNum: json.rowNum, rowList: JSON.parse(json.rowList), pager: pager, sortname: json.sortName, caption: json.caption, viewrecords: true, viewsortcols: true, sortorder: json.sortOrder, footerrow: summaryFooter, userDataOnFooter: summaryFooter, jsonReader: { root: "rows", row: "row", repeatitems: false, id: json.sortName }, gridComplete: function() { if (showFooter) { $(ph).append("" + json.footerRow + ""); } if (json.additionalContent != null) { $("#" + xContID).html(json.additionalContent); } $("ui-icon-asc").append("IMG"); var _rows = $(".jqgrow"); if (json.rows.length 0) { for (var i = 1; i < _rows.length; i += 1) { _rows[i].attributes["class"].value = _rows[i].attributes["class"].value.replace(" ui-jqgrid-altrow", ""); if (i % 2 == 1) { _rows[i].attributes["class"].value += " ui-jqgrid-altrow"; } } var gMaxHeight = getGridMaxHeight(); var gHeight = ($(ph + " tr").length + 1) * ($($(".jqgrow") [0]).height()); if (gHeight <= gMaxHeight) { $(ph).parent().height(gHeight); } else { $(ph).parent().height(gMaxHeight); } } else { $(ph).prepend("" + gridNoDataMsg + ""); $(ph).parent().height(60); } }, onSortCol: function(index, iCol, sortorder) { dataUrl = dataUrl.replace("&jqSession=true", ""); $(ph).jqGrid().setGridParam({ url: dataUrl }).trigger("reloadGrid"); var colName = "#jqgh" + index; // $(_prevSort).parent().removeClass("ui-jqgrid-sorted"); // $(_prevSort).parent().addClass("ui-state-default"); // $(_colName).parent().addClass("ui-jqgrid-sorted"); // $(_colName).parent().removeClass("ui-state-default"); _prevSort = _colName; var _rows = $(".jqgrow"); for (var i = 1; i < _rows.length; i += 1) { _rows[i].attributes["class"].value = _rows[i].attributes["class"].value.replace(" ui-jqgrid-altrow", ""); if (i % 2 == 1) { _rows[i].attributes["class"].value += " ui-jqgrid-altrow"; } } } }).navGrid('#' + pager, { search: false, sort: false, edit: false, add: false, del: false, refresh: false }); // end of grid $("#" + loadid).empty(); gGridIds[gGridIds.length] = placeHolder; SetGridSizes(); }, error: function() { $("#" + loadid).html(loadingErr); } }); As you can see from the code i am getting column collection dynamically(Appication page which i am calling will give me JSON in the response and will have colNames collection in it. Evrything is working fine but, only issue is coming when we are trying to apply custom formatter to column. This issue comes only when we are dynamically assign "colModel" to jqgrid. Appreciate help Thanks in advance

  Read the article

< Previous Page | 794 795 796 797 798 799 800 801 802 803 804 805  | Next Page >