Search Results

Search found 220 results on 9 pages for 'ancient fry up'.

Page 8/9 | < Previous Page | 4 5 6 7 8 9  | Next Page >

• Radeon HD4850 serious issues when using DirectX 10

  - by ricsmania

  Hello, I have a problem with my video card. Whenever I run a DirectX 10 game, it works for a few seconds (10 or so) and then starts displaying nothing but big polygons. I have tested this with Crysis and Resident Evil 5, both have the same problems. The same games running under DirectX 9 work fine, except for some small black squares once in a while. I have the following specs: Asus P7P55D LE Intel Core i5 750 Sapphire Radeon HD4850 1GB 2x2GB Patriot Viper II Sector 5, DDR3 1600 MHz OCZ Stealth X Stream 500SXS 500W At first I thought it could be the video card overheating (it has stock cooling), but the game crashes even when it's running at 50 degrees C, and it's never been higher than 70. I also thought it could be the PSU, but as far as I know 500W is enough for this computer, especially because I haven't overclocked anything. My OS is Windows 7 X64 and I am using Catalyst 10.10, but I have also tried many older versions with no success. I don't think there is a problem with the card itself, or else it wouldn't run DirectX 9 games I believe. I have spent many hours searching for a solution but I couldn't, so any help is appreciated. Thank you. EDIT: I did some further investigation about the problem, and it seems taspeotis was right, it might be related to memory. I slightly underclocked the memory from 993 to 965 MHz and the problem went away completely. Both the black squares using DirectX 9 and the weird polygons using DirectX 10. I was using RE DirectX 10 Benchmark, as it consistently crashed around the same point, and now I can play the full benchmark with no artifacts at all. Unfortunately, the underclock has an obvious hit in performance. Although it's not critical, it's definitely noticeable. So, if the video memory test software showed no erros, but the card needs an underclock to work, what might be the problem? Temperature? Voltage? By the way, I couldn't find what the default voltage for this card is. And what is a good software to try and increase it? I tried Ati Tray Tools but it has a bug that increases the clock speed dramatically whenever I change something in the Overclock tab, so I'm afraid it might fry my card. Worst case scenario, if I don't find I solution I will try to slightly increase the GPU clock to compensate for the memory clock. Thank you again.

  Read the article

• Browsing Your ADF Application Module Pooling Params with WLST

  - by Duncan Mills

  In ADF 11g you can of course use Enterprise Manager (EM) to browse and configure the settings used by ADF Business Components  Application Modules, as shown here for one of my sample deployed applications. This screen you can access from the EM homepage by pulling down the Application Deployment menu, and then ADF > Configure ADF Business Components. Then select the profile that you are actually using (Hint: look in the DataBindings.cpx file to work this out - probably the "Local" version unless you've explicitly changed it. )So, from this screen you can change the pooling parameters and the world is good. But what if you don't have EM installed? In that case you can use the WebLogic scripting capabilities to view (and Update) the MBean Properties. Explanation The pooling parameters and many others are handled through Message Driven Beans that are created for the deployed application in the server. In the case of the ADF BC pooling parameters, this MBean will combine the configuration deployed as part of the application, along with any overrides defined as -D environement commands on the JVM startup for the application server instance. Using WLST to Browse the Bean ValuesFor our purposes here I'm doing this interactively, although you can also write a script or write Java to achieve the same thing.Step 0: Before You Start You will need the followingAccess to the console on the machine that is running the serverThe WebLogic Admin username and password (I'll use weblogic/password as my example here - yours will be different)The name of the deployed application (in this example FMWdh_application1)The package path to the bc4j.xcfg file (in this example oracle.demo.fmwdh.model.service.common.bc4j.xcfg) This is based on the default path for your model project so it shoudl be fairly easy to work out.The BC configuration your AM is actually running with (look in the DataBindings.cpx for that. In this example DealHelpServiceDeployed is the profile being used..)Step 1: Start the WLST consoleTo start at the beginning, you need to run the WLST command but that needs a little setup:Change to the wlserver_10.3/server/bin directory e.g. under your Fusion Middleware Home[oracle@mymachine] cd /home/oracle/FMW_R1/wlserver_10.3/server/binSet your environment using the setWLSEnv script. e.g. on Oracle Enterprise Linux:[oracle@mymachine bin] source setWLSEnv.shStart the WLST interactive console[oracle@mymachine bin] java weblogic.WLSTInitializing WebLogic Scripting Tool (WLST) ...Welcome to WebLogic Server Administration Scripting ShellType help() for help on available commandswls:/offline> Step 2:Enter the WLST commandsConnect to the server wls:> connect('weblogic','password')Change to the Custom root, this is where the AMPooling MBeans are registered wls:> custom()Change to the b4j MBean directorywls:> cd ('oracle.bc4j.mbean.config')Work out the correct directory for the AM configuration you need. This is the difficult bit, not because it's hard to do, but because the names are long. The structure here is such that every child MBean is displayed at the same level as the parent, so for each deployed application there will be many directories shown. In fact, do an ls() command here and you'll see what I mean. Each application will have one MBean for the app as a whole, and then for each deployed configuration in the .xcfg file you'll see: One for the config entry itself, and then one each for Security, DB Connection and AM Pooling. So if you deploy an app with just one configuration you'll see 5 directories, if it has two configurations in the .xcfg you'll see 9 and so on.The directory you are looking for will contain those bits of information you gathered in Step 0, specifically the Application Name, the configuration you are using and the xcfg name: First of all narrow your list to just those directories returned from the ls() command that begin oracle.bc4j.mbean.config:name=AMPool. These identify the AM pooling MBeans for all the deployed applications. Now look for the correct application name e.g. Application=FMWdh_application1The config setting in that sub-list should already be correct and match what you expect e.g. oracle.bc4j.mbean.config=oracle.demo.fmwdh.model.service.common.bc4j.xcfgFinally look for the correct value for the AppModuleConfigType e.g. oracle.bc4j.mbean.config.AppModuleConfigType=DealHelpServiceDeployedNow you have identified the correct directory name, change to that (keep the name on one line of course - I've had to split it across lines here for clarity:wls:> cd ('oracle.bc4j.mbean.config:name=AMPool,     type=oracle.bc4j.mbean.config.AppModuleConfigType.AMPoolType,    oracle.bc4j.mbean.config=oracle.demo.fmwdh.model.service.common.bc4j.xcfg,    Application=FMWdh_application1,    oracle.bc4j.mbean.config.AppModuleConfigType=DealHelpServiceDeployed') Now you can actually view the parameter values with a simple ls() commandwls:> ls()And here's the output in which you can view the realtime values of the various pool settings: -rw- AmpoolConnectionstrategyclass oracle.jbo.common.ampool.DefaultConnectionStrategy -rw- AmpoolDoampooling true -rw- AmpoolDynamicjdbccredentials false -rw- AmpoolInitpoolsize 2 -rw- AmpoolIsuseexclusive true -rw- AmpoolMaxavailablesize 40 -rw- AmpoolMaxinactiveage 600000 -rw- AmpoolMaxpoolsize 4096 -rw- AmpoolMinavailablesize 2 -rw- AmpoolMonitorsleepinterval 600000 -rw- AmpoolResetnontransactionalstate true -rw- AmpoolSessioncookiefactoryclass oracle.jbo.common.ampool.DefaultSessionCookieFactory -rw- AmpoolTimetolive 3600000 -rw- AmpoolWritecookietoclient false -r-- ConfigMBean true -rw- ConnectionPoolManager oracle.jbo.server.ConnectionPoolManagerImpl -rw- Doconnectionpooling false -rw- Dofailover false -rw- Initpoolsize 0 -rw- Maxpoolcookieage -1 -rw- Maxpoolsize 4096 -rw- Poolmaxavailablesize 25 -rw- Poolmaxinactiveage 600000 -rw- Poolminavailablesize 5 -rw- Poolmonitorsleepinterval 600000 -rw- Poolrequesttimeout 30000 -rw- Pooltimetolive -1 -r-- ReadOnly false -rw- Recyclethreshold 10 -r-- RestartNeeded false -r-- SystemMBean false -r-- eventProvider true -r-- eventTypes java.lang.String[jmx.attribute.change] -r-- objectName oracle.bc4j.mbean.config:name=AMPool,type=oracle.bc4j.mbean.config.AppModuleConfigType.AMPoolType,oracle.bc4j.mbean.config=oracle.demo.fmwdh.model.service.common.bc4j.xcfg,Application=FMWdh_application1,oracle.bc4j.mbean.config.AppModuleConfigType=DealHelpServiceDeployed -rw- poolClassName oracle.jbo.common.ampool.ApplicationPoolImpl Thanks to Brian Fry on the JDeveloper PM Team who did most of the work to put this sequence of steps together with me badgering him over his shoulder.

  Read the article

• Day 1 - Finding Like Minds

  - by dapostolov

  So, is being a Game Developer any different from being an IT Developer? I picture a poorly lit environment where I get to purchase my own desk lamp; I'm thinking one of those huge lava lamps that pump out so much heat you could fry an egg on it. To my right: a "great wall" of empty coke cans dwarf me. Eating my last slice of pizza I look across my desk to see a fellow developer with a smug look on his face;  he's just coded his latest module for the game and it looks like he's in nirvana. My duty, of course, is to remind him to keep focused on the job at hand. So, picking up my trusty elastic and aerodynamically crafted paper bullet I begin a 10 minute war of welts and laughter which is promptly abrupted by our Project Manager demanding more details from our morning Scrum meeting. After providing about 5 minutes of geek speak and several words of comfort to make his eyes glaze over...it hits me, the idea for the module...beckoning my developer friend over, we quickly shoo the Project Manager away and begin our brainstorming frenzy ... now, where'd I put that full can of coke? OK. OK. This isn't probably the most ideal game developer environment, but it definitely sounds fun to me...and from what I gather is nothing like most game development companies. But I'm not doing this blog series to "go pro"; like I stated in my first post I want to make a 2D game from an idea my best friend and I drummed up long, long ago. I'm in this for the passion AND I want to see how easy it is for us .Net Developers to create a game. So where do I start? Where can I find like minded individuals? What technologies are there? What do I need to make a video game? The questions are endless....AND...since I already have an idea ... lets start with ... Technology (yes, I'm a geek, live with it...) Technology OK. Predominantly, games are still made in C++ or even C. I'm not sure how much assembly code is floating around lately, however, that is not my concern. I do know C / C++ from my past, enough to even get me by, but I'm mainly interested in a recent, not-so-new, technology called XNA. What is XNA? XNA allows us .Net Developers to make 2D / 3D games for windows, Xbox*, and Windows Mobile 7*. * = for a nominal fee *cough* The following link is your one stop shop to XNA game development: http://creators.xna.com/en-US/education/gettingstarted The above site hosts information such as: - getting started - a sample/instructional shooter game in 2D / 3D with code (if I'm taking too long for you in this blog series) - downloads - starter kits... http://creators.xna.com/en-US/education/starterkits/ And of course...forums. You can also subscribe and pay for their premium membership which gets you some pretty awesome tutorials, resources, downloads, and premium community support. Some general Wiki information about XNA: http://en.wikipedia.org/wiki/XNA_%28Microsoft%29 Community Support OK. Let's move on to industry and community support. Apart from XNA, there are some really cool sites out there, I just haven't found all of them yet. However, I found a really cool Game Development website called Gamastura. You can click on the following link to get you there: http://www.gamasutra.com/ The site is 100% dedicated to "The Art & Business of Making Games". Armed with blogs, twitter, jobs/resumes and most importantly industry news; one could subscribe to the feed and got lost in the wealth of information it provides. On a side note: I remember Gamasutra being around when my best friend and I wanted to make a video game...meaning, they've been around for a while now. I think the most beneficial aspect of this site is to understand the industry you want to get into. Otherwise, it's just a cool site to keep up to date with the industry in general. Another Community Support option is LinkedIn. Amongst the land of extremely bloated achievements and responsibilities lay 3 groups (that I have found) that deal with game development.: http://www.linkedin.com/groups?gid=59205 - Game Developers http://www.linkedin.com/groups?gid=824817 - DirectX Game Developer Network http://www.linkedin.com/groups?gid=756587 - DirectX Developers The Game Developers group in LinkedIn is by far the most active of the three and could possibly provide a wealth of support. What I've done thus far: - I lightly researched the XNA technology - I looked around for some community sites to assist me - I downloaded the XNA Game Studio 3.1 on my PC and installed it on my IDE - I even tried both tutorials! http://creators.xna.com/en-US/education/gettingstarted/bgintro/chapter1   Best Regards D.

  Read the article

• SQL SERVER – SQL Server Misconceptions and Resolution – A Practical Perspective – TechEd 2012 India

  - by pinaldave

  TechEd India 2012 is just around the corner and I will be presenting there in two different sessions. On the very first day of this event, my presentation will be all about SQL Server Misconceptions and Resolution – A Practical Perspective. The dictionary tells us that a “misconception” means a view or opinion that is incorrect and is based on faulty thinking or understanding. In SQL Server, there are so many misconceptions. In fact, when I hear some of these misconceptions, I feel like fainting at that very moment! Seriously, at one time, I came across the scenario where instead of using INSERT INTO…SELECT, the developer used CURSOR believing that cursor is faster (duh!). Here is the link the blog post related to this. Pinal and Vinod in 2009 I have been presenting in TechEd India for last three years. This is my fourth opportunity to present a technical session on SQL Server. Just like the previous years, I decided to present something different. Here is a novelty of this year: I will be presenting this session with Vinod Kumar. Vinod Kumar and I have a great synergy when we work together. So far, we have written one SQL Server Interview Questions and Answers book and 2 video courses: (1) SQL Server Questions and Answers (2) SQL Server Performance: Indexing Basics. Pinal and Vinod in 2011 When we sat together and started building an outline for this course, we had many options in mind for this tango session. However, we have decided that we will make this session as lively as possible while keeping it natural at the same time. We know our flow and we know our conversation highlight, but we do not know what exactly each of us is going to present. We have decided to challenge each other on stage and push each other’s knowledge to the verge. We promise that the session will be entertaining with lots of SQL Server trivia, tips and tricks. Here are the challenges that I’ll take on: I will puzzle Vinod with my difficult questions I will present such misconception that Vinod will have no resolution for it. I need your help.  Will you help me stump Vinod? If yes, come and attend our session and join me to prove that together we are superior (a friendly brain clash, but we must win!). SQL Server enthusiasts and SQL Server fans are going to have gala time at #TechEdIn as we have a very solid lineup of the speaker and extremely interesting sessions at TechEdIn. Read the complete blog post of Vinod. Session Details Title: SQL Server Misconceptions and Resolution – A Practical Perspective (Add to Calendar) Abstract: “Earth is flat”! – An ancient common misconception, which has been proven incorrect as we progressed in modern times. In this session we will see various database misconceptions prevailing and their resolution with the aid of the demos. In this unique session audience will be part of the conversation and resolution. Date and Time: March 21, 2012, 15:15 to 16:15 Location: Hotel Lalit Ashok - Kumara Krupa High Grounds, Bengaluru – 560001, Karnataka, India. Add to Calendar Please submit your questions in the comments area and I will be for sure discussing them during my session. If I pick your question to discuss during my session, here is your gift I commit right now – SQL Server Interview Questions and Answers Book. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Interview Questions and Answers, SQL Performance, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology Tagged: TechEd, TechEdIn

  Read the article

• SQL SERVER – #TechEdIn – Presenting Tomorrow on SQL Server Misconception and Resolution with Vinod Kumar at TechEd India 2012

  - by pinaldave

  I am excited AND nervous at the same time. I am going to present a very interesting topic tomorrow at an SQL Server track in India. This will be my fourth time presenting at TechEd India. So far, I have received so much feedback about this one session. It seems like every single person out there has their own wishes and requests. I am sure that it is going to very challenging experience to satisfy everyone who attends the event through my presentation. Surprise Element Here is the good news: I am going to co-present this session with Vinod Kumar, my long time friend and co-worker. We have known each other for almost four years now, but this is the very first time that we are going to present together on the big stage of TechEd.  When there are more than two presenters, the usual trick is to practice the session multiple times and know exactly what each other is going to present and talk about. However, there’s a catch – we decided to make it different this time and have shared nothing to each other regarding what exactly we are going to present. This makes everything extremely interesting as each of us will be as clueless as the audience when other person is going to talk. Action Item Here are a few of the action items for all of those who are going to attend this session. Vinod and I will be present at the venue 15 minutes before the session. Do come in early and talk with us. We would be glad to talk with you and see if either of us can accommodate your suggestion in our session. If we do, we will give a surprise gift for you. As discussed, this session is going to be a unique two-presenter session. You will have chance to take a side with one speaker and stump the other speaker. Come early to decide which speaker you want to cheer during the session. Quiz and Goodies By now, you must have figured out that this session is going to be an extremely interactive session. We need your support through your active participation. We will have some really brain-twisting quiz line up just for you. You will have to take part and win surprises from us! Trust me. If you get it right, we will give you something which can help you learn more! We will have a quiz on Twitter as well. We will ask a question in person and you will be able to participate on Twitter. 10 – Demos As I said, both of us do not know what each other is going to present, but there are few things which we know very well. We have 10 demos and 6 slides. I think this is going to be an exciting demo marathon. Trust me, you will love it and the taste of this session will be in your mouth till the next TechEd. Session Details Title: SQL Server Misconceptions and Resolution – A Practical Perspective (Add to Calendar) Abstract: “The earth is flat”! – An ancient common misconception, which has been proven incorrect as we progressed in modern times. In this session, we will see various database misconceptions prevailing and their resolutions with the aid of the demos. In this unique session, the audience will be a part of the conversation and resolution. Date and Time: March 21, 2012, 15:15 to 16:15 Location: Hotel Lalit Ashok - Kumara Krupa High Grounds, Bengaluru – 560001, Karnataka, India. Add to Calendar Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Interview Questions and Answers, SQL Query, SQL Server, SQL Tips and Tricks, SQLServer, T SQL, Technology

  Read the article

• A tiny Utility to recycle an IIS Application Pool

  - by Rick Strahl

  In the last few weeks I've annoyingly been having problems with an area on my Web site. It's basically ancient articles that are using ASP classic pages and for reasons unknown ASP classic locks up on these pages frequently. It's not an individual page, but ALL ASP classic pages lock up. Ah yes, gotta old tech gone bad. It's not super critical since the content is really old, but still a hassle since it's linked content that still gets quite a bit of traffic. When it happens all ASP classic in that AppPool dies. I've been having a hard time tracking this one down - I suspect an errant COM object I have a Web Monitor running on the server that's checking for failures and while the monitor can detect the failures when the timeouts occur, I didn't have a good way to just restart that particular application pool. I started putzing around with PowerShell, but - as so often seems the case - I can never get the PowerShell syntax right - I just don't use it enough and have to dig out cheat sheets etc. In any case, after about 20 minutes of that I decided to just create a small .NET Console Application that does the trick instead, and in a few minutes I had this:using System; using System.Collections.Generic; using System.Text; using System.DirectoryServices; namespace RecycleApplicationPool { class Program { static void Main(string[] args) { string appPoolName = "DefaultAppPool"; string machineName = "LOCALHOST"; if (args.Length > 0) appPoolName = args[0]; if (args.Length > 1) machineName = args[1]; string error = null; DirectoryEntry root = null; try { Console.WriteLine("Restarting Application Pool " + appPoolName + " on " + machineName + "..."); root = new DirectoryEntry("IIS://" + machineName + "/W3SVC/AppPools/" +appPoolName); Console.WriteLine(root.InvokeGet("Name")); root.Invoke("Recycle"); Console.WriteLine("Application Pool recycling complete..."); } catch(Exception ex) { error = "Error: Unable to access AppPool: " + ex.Message; } if ( !string.IsNullOrEmpty(error) ) { Console.WriteLine(error); return; } } } } To run in you basically provide the name of the ApplicationPool and optionally a machine name if it's not on the local box. RecyleApplicationPool.exe "WestWindArticles" And off it goes. What's nice about AppPool recycling versus doing a full IISRESET is that it only affects the AppPool, and more importantly AppPool recycles happen in a staggered fashion - the existing instance isn't shut down immediately until requests finish while a new instance is fired up to handle new requests. So, now I can easily plug this Executable into my West Wind Web Monitor as an action to take when the site is not responding or timing out which is a big improvement than hanging for an unspecified amount of time. I'm posting this fairly trivial bit of code just in case somebody (maybe myself a few months down the road) is searching for ApplicationPool recyling code. It's clearly trivial, but I've written batch files for this a bunch of times before and actually having a small utility around without having to worry whether Powershell is installed and configured right is actually an improvement. Next time I think about using PowerShell remind me that it's just easier to just build a small .NET Console app, 'k? :-) Resources Download Executable and VS Project© Rick Strahl, West Wind Technologies, 2005-2012Posted in IIS7  .NET  Windows   Tweet !function(d,s,id){var js,fjs=d.getElementsByTagName(s)[0];if(!d.getElementById(id)){js=d.createElement(s);js.id=id;js.src="//platform.twitter.com/widgets.js";fjs.parentNode.insertBefore(js,fjs);}}(document,"script","twitter-wjs"); (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

  Read the article

• Free hosting solution for a very low-traffic website [duplicate]

  - by user966939

  This question already has an answer here: How to find web hosting that meets my requirements? 4 answers I run a very low-traffic website (about 40 users, basically all of which are daily active on the site). I don't see it changing anytime soon either, as there is no way to sign up on the site right now. Until now I have just been using a sub-directory on a friend's host (shared), to host the web site. But in only a few weeks from now, his subscription will end, and he has no plans on renewing it. So of course this means I'll have to move on to something else. But I don't think I'll find someone who'd be willing to share a... shared host with me again. And besides, the software used on that server is ancient (PHP 4.4.9 + MySQL 4.1.22). There's one obvious solution that comes to mind, I guess: choose a better host and pay for it myself. The problem here is that I have no real fixed income, as I'm only a student. So even if the pricing is dirt cheap, I just can't be certain I will be able to afford it, every single month, for... at least 2 years maybe? So I've looked at free hosting solutions instead. The least requirement I had was that it was completely free of ads. But no matter where I look, I always find something in a corner or two ("what can you expect from a free host?" - yeah I know, but I guess it was worth a shot). For example, on Byethost (one of the free hosts I tried), if you trigger a PHP error while error reporting is set to E_ALL, you will spawn some hidden ad... Besides Byethost, I've tried 000Webhost, x10Hosting, 2Freehosting/1Freehosting, Wink.ws, and they are only worse. Okay, I'm running low on ideas. But! What if I just hosted the site myself, on my own computer? That could work. I actually do have my computer on practically 24/7. But not really. Sometimes I need to reboot it, and sometimes we even have power outages. And what if the hardware needs an upgrade? It's not such a big deal for me if the site went down, because I know what's going on; but what about the users? If I do decide to host it myself, is there some way to show users an alternate page instead of them just seeing a generic "server not found" page in the browser when the site is not accessible? Or is there something I have been missing out on? Is there a different kind of "web hosting" solution out there that I haven't heard of? Here is what I'm really looking for: Free (as in, no costs) NO ads Bandwidth enough for a low-traffic forum with roughly 40 users (Semi-)Up-to-date PHP and MySQL (at least not older than a year) No standard (non-extension) PHP functions turned off - such as sleep() The mbstring extension is enabled Disk space: at least 5 MB At least one MySQL database Some bonus points would be: Max execution time of PHP scripts can be set Remote access to MySQL database What would be the best solution for me? Is there one?

  Read the article

• Video works with 'Try me' but not after install. What is the difference? U12.04LTS,

  - by HarveyP

  My hard drive got corrupted so I did a reinstall. Tested Youtube in FF during 'try me' and it worked - jerky, but it worked. Instal without all the updates (576 outstanding now) in order to get ff installed as per the demo - to no avail. In 'try me' mode ff NEVER crashed! After install ff crashed whilst I was typing in 'youtube' in the address field. When I finally got to youtube - no video. What is the difference between ff in try me and ff after install? Off to try some selected updates now to see if I can see it for myself. In previous installation I had several profiles and aliased ff with -safe-mode switch to simplify startup of most stable ff. Also found that ff startup in graphic mode worked better (but still without video) with all of the extensions disabled and all of the plugins set to "ask" and always denied ... I have SiS graphic card in SiS Motherboard for XP and ancient Hyundai ImageQuest QV770 monitor. I have Ubuntu 12.04.01 LTS 1 day after install with only the immediate upgrades requested to language pack (English UK). Using FR Alternative keyboard. Connected with domestic wifi network from Orange (FT) I really want to use Skype, but won't bother installing it (again) without video as I can do my sms on FB - whilst ff is not crashed ... Update ... Is something overflowing? I have just had to reboot in order to get ff to restart in any way shape or form - restart on crash form generates new crash form, etc. It was however a good half hour before it crashed so some improvement over conditions before disk corruption. I have now installed all of the critical updates (332 recommended updates still outstanding) which included some relating to ff. Still no video. Still crashing - especially when on Grepolis website. Since the re-install I have had a lovely 1024x768 screen, but after last ff crash and reboot I got a message about 'low graphics mode' and 'setting things myself'. I was not sufficiently tuned in at the time to take proper note - I have no doubt I shall see it again and shall report accordingly. I still have only laptop options for my screen and do not know how to rectify this. Spent a few days with ubuntu on a different, newer machine which has now suffered a graphics breakdown. Returned to this old one again, but with new flat screen Monitor. Found SIS drivers for my graphics BUT it is intended for Red Hat 7.2. I chose this over the version for 7.0 because I thought what the hell, I might not be able to do anything with either of them but this is the later one ... The file will not open with software manager - found a similar problem on Overclock but it has not helped me to install this driver. File name is sis_drv.o-410 and it is currently idling away in my Downloads folder ... I have tried the solution offered on another sis problem, but this shows that my xserver-xorg-video-sis driver is up to date. I am now at a loss as to how to proceed if I can't install the latest sis driver from sis ... Does nobody know how FF changes from "try-me" to "installed"? Any time I MUST have video I reboot from the disk again, but this is tedious! Also one of the things I mock most about MS is the constant rebooting ... UPDATE 10/6/2014 I have installed chromium-browser - worse, crashes even more often than ff.I have installed epiphany - better; Video works but not the associated soundtrack.FireFox is version 14.01 in 'try me' and version 29.0 from my install. Would it be useful to try to downgrade FireFox in order to get video?

  Read the article

• Visual Studio 2010 is asking to convert RDLC created on VS2008 to RDLC 2008 format?

  - by Junior Mayhé

  I've created my project on Visual Studio 2008, as well RDLC files on it. But now, when I open the solution on Visual Studio 2010 and want to open RDLC file, it's showing me a warning. That's a little funny. The report was created on VS2008 and VS2010 is asking to convert to 2008 format. Perhaps there was a problem on my VS2008 installation that created RDLC files using some ancient format (2005??!) The problem is, when you confirm with Ok button, do some design ajustments and run the app, it throws an error on 'Main report': ex.InnerException {"The definition of the report 'Main Report' is invalid."} [Microsoft.Reporting.DefinitionInvalidException]: {"The definition of the report 'Main Report' is invalid."} Data: {System.Collections.ListDictionaryInternal} HelpLink: null InnerException: {"The report definition is not valid. Details: The report definition has an invalid target namespace 'http://schemas.microsoft.com/sqlserver/reporting/2008/01/reportdefinition' which cannot be upgraded."} Message: "The definition of the report 'Main Report' is invalid." Source: "Microsoft.ReportViewer.Common" StackTrace: " at Microsoft.Reporting.ReportCompiler.CompileReport(CatalogItemContext context, Byte[] reportDefinition, Boolean generateExpressionHostWithRefusedPermissions, ReportSnapshotBase& snapshot)\r\n at Microsoft.Reporting.StandalonePreviewStore.StoredReport.CompileReport()\r\n at Microsoft.Reporting.StandalonePreviewStore.StoredReport.get_Snapshot()\r\n at Microsoft.Reporting.StandalonePreviewStore.GetCompiledReport(CatalogItemContext context, Boolean rebuild, ReportSnapshotBase& snapshot)\r\n at Microsoft.Reporting.LocalService.GetCompiledReport(CatalogItemContext itemContext, Boolean rebuild, ReportSnapshotBase& snapshot)\r\n at Microsoft.Reporting.LocalService.CompileReport(CatalogItemContext itemContext, Boolean rebuild)\r\n at Microsoft.Reporting.WinForms.LocalReport.CompileReport()" TargetSite: {Microsoft.ReportingServices.ReportProcessing.PublishingResult CompileReport(Microsoft.ReportingServices.Diagnostics.CatalogItemContext, Byte[], Boolean, Microsoft.ReportingServices.Library.ReportSnapshotBase ByRef)}

  Read the article

• Schliemann's method of programming language learning

  - by DVK

  Background: 19th-century German archeologist Heinrich Schliemann was of course famous for his successful quest to find and excavate the city of Troy (an actual archeological site for the Troy of Homer's Iliad). However, he is just as famous for being an astonishing learner of languages - within the space of two years, he taught himself fluent Dutch, English, French, Spanish, Italian and Portuguese, and later went on to learn seven more, including both modern and ancient Greek. One of the methods he famously used was comparison of a known text, e.g. take a book in a language one is fluent in, take a good translation of a book in a language you wish to learn, and go over them in parallel. (various sources cited the book used by Schliemann to be the Bible, or, as the link above states, a novel). Now, for the actual question. Has anyone used (or heard of) an equivalent of Schliemann's method for learning a new programming language? E.g. instead of basing the leaning on references and tutorials, take a somewhat comprehensive set of programs known to have high-quality code in both languages implementing similar/identical algorithms and learn by comparing them? I'm curious about either personal experiences of applying such an approach, or references to something published, or existance of codebases which could be used for such an approach? What got me thinking about the idea was Project Euler and some code snippets I saw on SO, in C++, Perl and Lisp.

  Read the article

• iPad Safari's mapping of mouse events to touch events in image-maps

  - by Tim

  My website makes extensive use of image-maps. The images are of pages from a medieval manuscript. The mouseOver event of the AREA tags has a tooltip attached to it, which displays a modern typographic transcription of the ancient script for the line the mouse is hovering over. I just checked my website out on the iPad at the Apple store. The iPad is many respects a joy to use, however, I am wondering about Apple's mapping of the mouseEvents to the finger-touch events. Apple probably had a good reason for doing things as they did, but their choices seem counterintuitive an overly complicated to me. Specifically, the iPad Safari browser clearly was responding to both fingerDown and fingerTap, and in different ways. When I tapped an area of the image-map, the tooltip wired to the mouse-over event pf the AREA tag was displayed, and remained visible until I tapped somewhere else. When I held my finger down on an area of the image-map, the area changed color. So if iPad Safari detects a mouseOver eventhandler, it executes the mouseOver code and apparently prevents the "click" event from propagating, so that if you also have something wired to the click event, it doesn't work? Is that right? But more importantly, why isn't fingerDown the iPad-Safari counterpart for mouseOver? FingerDown seems a more likely candidate than Tap when mapping the mousePOver event. I would have expected things to be mapped in this way: MouseClick : FingerTap (i.e. finger down and then immediately up) MouseOver : FingerDown (finger down and stays on the spot) If Apple had treated fingerDown as the counterpart to mouseOver, then the tooltip could be displayed upon FingerDown and made invisible again on fingerUp, which would be the counterpart to mouseOut. Perhaps someone could enlighten me about the thinking process that led Apple to these particular mouse-to-touch event-mappings? Thanks

  Read the article

• Google GWT cross-browser support: is it BS ?

  - by Tim

  I developed a browser-deployed full-text search app in FlashBuilder which communicates RESTfully with a remote web-server. The software fits into a tiny niche--it is for use with ancient languages not modern ones, and there's no way I'm going to make any money on it but I did spend a lot of time on it. Now that Apple won't allow Flash on the iPad, I'm looking for a 100% javascript solution and was led to consider GWT. It looked promising, but one of the apps being "showcased" as a stellar example of what can be done with GWT has this disclaimer on their website (names {removed} to protect the potentially innocent) : Your current web browser (Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US) AppleWebKit/532.5 (KHTML, like Gecko) Chrome/4.1.249.1045 Safari/532.5) is not officially supported by {company and product name were here}. If you experience any problems using this site please install either Microsoft Internet Explorer 6+ or Mozilla Firefox 3.5+ before contacting {product name was here} Support. What gives when GWT apps aren't "officially" supported on Chrome? What grade (A, B, C, D, F) would you give to GWT for cross-browser support? For folks who don't get these kinds of letter grades, A is "excellent" and "F" is failure, and "C" is average. Thanks for your opinions.

  Read the article

• [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified - works

  - by Matt

  Hello, I am developing a java app (with odbc bridge - forgive me - the only paradox driver I have been able to obtain is the microsoft odbc driver) - which works fine while in eclipse, (and netbeans) - connecting and obtaining data from an ancient paradox 5.x database. So long as it is run from inside my IDE - it compiles and runs flawlessly. When I export it to a runable jar, suddenly [code][Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified[/code] occurs. The jar is being run on the same box as my developing IDE - so I am confused about the cause. It is being run via console from a user account, as per the IDE. My connection string is "jdbc:odbc:Driver={Microsoft Paradox Driver (*.db )};DriverID=538; Fil=Paradox 5.X; DefaultDir=C:\paradox\database\location\" - obtained from connectionstrings.com - and as mentioned before, working fine while run from the IDE. The above seems to 'magically' create its own connection, avoiding the setup of a dsn - I am unsure quite how it does - but it works. The only other thing I can think that might be pertinent is that my PC is a 64bit o/s (windows server 2008). Please help, any suggestions or comments will be greatly appreciated. Thanks, Matt

  Read the article

• Datatable add new column and values speed issue

  - by Cine

  I am having some speed issue with my datatables. In this particular case I am using it as holder of data, it is never used in GUI or any other scenario that actually uses any of the fancy features. In my speed trace, this particular constructor was showing up as a heavy user of time when my database is ~40k rows. The main user was set_Item of DataTable. protected myclass(DataTable dataTable, DataColumn idColumn) { this.dataTable = dataTable; IdColumn = idColumn ?? this.dataTable.Columns.Add(string.Format("SYS_{0}_SYS", Guid.NewGuid()), Type.GetType("System.Int32")); JobIdColumn = this.dataTable.Columns.Add(string.Format("SYS_{0}_SYS", Guid.NewGuid()), Type.GetType("System.Int32")); IsNewColumn = this.dataTable.Columns.Add(string.Format("SYS_{0}_SYS", Guid.NewGuid()), Type.GetType("System.Int32")); int id = 1; foreach (DataRow r in this.dataTable.Rows) { r[JobIdColumn] = id++; r[IsNewColumn] = (r[IdColumn] == null || r[IdColumn].ToString() == string.Empty) ? 1 : 0; } Digging deeper into the trace, it turns out that set_Item calls EndEdit, which brings my thoughts to the transaction support of the DataTable, for which I have no usage for in my scenario. So my solution to this was to open editing on all of the rows and never close them again. _dt.BeginLoadData(); foreach (DataRow row in _dt.Rows) row.BeginEdit(); Is there a better solution? This feels too much like a big giant hack that will eventually come and bite me. You might suggest that I dont use DataTable at all, but I have already considered that and rejected it due to the amount of effort that would be required to reimplement with a custom class. The main reason it is a datatable is that it is ancient code (.net 1.1 time) and I dont want to spend that much time changing it, and it is also because the original table comes out of a third party component.

  Read the article

• Downloading jQuery UI: Ok, so what part of this mess do I copy to the server?

  - by Martha

  From the "should be simple, but..." files: Trying to get started with jQuery UI. Went to the site, used their custom builder thingy to assemble the parts I need, made myself a custom theme using the Theme Roller, downloaded the zip file thus produced, unzipped it on my local drive. Ok, so I have 37 folders, 311 files, and a total of 2.4 MB. Ain't no way in hell all this is going on the server. What parts do I need to put there? 'css' 'custom-theme': jquery-ui-1.8.custom.css, 'images' subfolder with 12 .png images 'development-bundle' 'demos': demos.css, index.html, plus 18 subfolders, but I'm guessing "not needed" 'docs': 17 .html files, but again, I'm guessing "not needed" 'external': 4 .js files, one .css 'themes': 'base' and 'custom-theme' subfolders, each with 8 or 9 .css files and an 'images' subfolder with about a dozen images 'ui': 25 .js files, an 'i18n' subfolder with 53 .js files, and a 'minified' subfolder with 24 .js files 'js': jquery-1.4.2.min.js and jquery-ui-1.8.custom.min.js Also, the file structure. Our server is set up something like this: root admin (administrative tools) css forms (the gist of the site lives here) images include (asp code snippets that are used by multiple pages) js (just a few things right now, like an ancient wheezing spelling checker) As far as I can tell, the jQuery css files assume that (1) each theme is in its own folder, and (2) each folder has its own images subfolder. How can I convince it otherwise? i.e. put the necessary .js files in the 'js' folder, the .css files in the 'css' folder, and the images in the 'images' folder?

  Read the article

• Python Post Upload JPEG to Server?

  - by iJames

  It seems like this answer has been provided a bunch of times but in all of it, I'm still getting errors from the server and I'm sure it has to do with my code. I've tried HTTP, and HTTPConnection from httplib and both create quite different terminal outputs in terms of formatting/encoding so I'm not sure where the problem lies. Does anything stand out here? Or is there just a better way? Pieced together from an ancient article because I really needed to understand the basis of creating the post: http://code.activestate.com/recipes/146306-http-client-to-post-using-multipartform-data/ Note, the jpeg is supposed to be "unformatted". The pseudocode: boundary = "somerandomsetofchars" BOUNDARY = '--' + boundary CRLF = '\r\n' fields = [('aspecialkey','thevalueofthekey')] files = [('Image.Data','mypicture.jpg','/users/home/me/mypicture.jpg')] bodylines = [] for (key, value) in fields: bodylines.append(BOUNDARY) bodylines.append('Content-Disposition: form-data; name="%s"' % key) bodylines.append('') bodylines.append(value) for (key, filename, fileloc) in files: bodylines.append(BOUNDARY) bodylines.append('Content-Disposition: form-data; name="%s"; filename="%s"' % (key, filename)) bodylines.append('Content-Type: %s' % self.get_content_type(fileloc)) bodylines.append('') bodylines.append(open(fileloc,'r').read()) bodylines.append(BOUNDARY + '--') bodylines.append('') #print bodylines content_type = 'multipart/form-data; boundary=%s' % BOUNDARY body = CRLF.join(bodylines) #conn = httplib.HTTP("www.ahost.com") # In both this and below, the file part was garbling the rest of the body?!? conn = httplib.HTTPConnection("www.ahost.com") conn.putrequest('POST', "/myuploadlocation/uploadimage") headers = { 'content-length': str(len(body)), 'Content-Type' : content_type, 'User-Agent' : 'myagent' } for headerkey in headers: conn.putheader(headerkey, headers[headerkey]) conn.endheaders() conn.send(body) response = conn.getresponse() result = response.read() responseheaders = response.getheaders() It's interesting in that the real code I've implemented seems to work and is getting back valid responses, but the problem it it's telling me that it can't find the image data. Maybe this is particular to the server, but I'm just trying to rule out that I'm not doing some thing exceptionally stupid here. Or perhaps there's other methodologies for doing this more efficiently. I've not tried poster yet because I want to make sure I'm formatting the POST correctly first. I figure I can upgrade to poster after it's working yes?

  Read the article

• C89, Mixing Variable Declarations and Code

  - by rutski

  I'm very curious to know why exactly C89 compilers will dump on you when you try to mix variable declarations and code, like this for example: rutski@imac:~$ cat test.c #include <stdio.h> int main(void) { printf("Hello World!\n"); int x = 7; printf("%d!\n", x); return 0; } rutski@imac:~$ gcc -std=c89 -pedantic test.c test.c: In function ‘main’: test.c:7: warning: ISO C90 forbids mixed declarations and code rutski@imac:~$ Yes, you can avoid this sort of thing by staying away from -pedantic. But then your code is no longer standards compliant. And as anybody capable of answering this post probably already knows, this is not just a theoretical concern. Platforms like Microsoft's C compiler enforce this quick in the standard under any and all circumstances. Given how ancient C is, I would imagine that this feature is due to some historical issue dating back to the extraordinary hardware limitations of the 70's, but I don't know the details. Or am I totally wrong there?

  Read the article

• How difficult is it for an old-school programmer to pick up an FPGA kit and make something useful wi

  - by JUST MY correct OPINION

  I'm an old, old, old coder. (How old? I've used paper tape in anger.) I've programmed in a lot of languages and under a lot of paradigms (spaghetti, structured, object-oriented, functional and a smattering of logical). I'm getting bored. FPGAs look interesting to me. I have the crazy notion of resurrecting some of the ancient hardware I worked on in the days using FPGAs. I know this can be done because I've seen PDP-10 and PDP-11 implementations in FPGAs. I'd like to do the same for a few machines that are perhaps not as popular as those two, however. While I am an old, old coder, what I am not is an electronics or computer systems engineer. I'll be learning from scratch if I go down this path. My question, therefore, is two-fold: How difficult will it be for this old dinosaur to pick up and learn FPGAs to the point that interesting (not necessarily practical -- more from a hobbyist perspective) projects can be made? What should I start with learning-wise to go down this path? I know where to get FPGA kits, but I haven't found anything like "FPGAs for Complete Dinosaurs" yet anywhere out there.

  Read the article

• Installing Mercurial on Windows Apache XAMPP Tutorial

  - by Tim Dellas

  After asking this question (http://stackoverflow.com/questions/2675764/xampp-mercurial-installation-on-windows-apache-hgwebdir-cgi-script-error) and reading though the whole internet including this question (http://stackoverflow.com/questions/644322/how-do-i-get-mercurials-hgwebdir-working-on-windows) and all its links for about 10 hours, I seem to not be able to find a solution. I begun with this tutorial http://mercurial.selenic.com/wiki/HgWebDirStepByStep ... and I really don't want to install ancient versions of Mercurial. I got my windows-apache to run Python scripts, CGI-Scripts, publish them in the wild, but hgwebdir just won't work. Question 1: Can someone please enrich his personal blog with a tutorial on how to install MERCURIAL on a WINDOWS XAMPP installation and make it visible to the world? I guarantee a lot of pageviews, as this is not a trivial problem. And this would sincerely help a lot of other people I guess. Question 2: For example, even after browsing half a day through everywhere, I just cannot find out, which version of python I need to pair with the freshest version of mercurial, and I get the "magic number is wrong"-error. This would be my question, if noone has time to make up a nice blogpost. Sorry for being a bit frustrated.

  Read the article

• Static libraries in version-cross-compiled program

  - by Brian Postow

  I have a unix command line app (with big nasty makefile) that I'm trying to run on a mac. I am compiling it on a 10.6 system, with all of the appropriate libraries of course. The deployment environment is a 10.5 system, with no extra libraries. I compiled without -dynamic, and it appears to have static libraries, correctly. When I run it on the 10.6 system, it works. However, when I run it on the 10.5 system, I get: dyld: unknown required load command 0x80000022 I got this same error when I compiled things for the 10.6 system using the 10.5 xcode, so it looks like a version mis-match type problem. However, I used gcc-4.0, and $CFLAGS = -isysroot /Developer/SDKs/MacOSX10.5.sdk -mmacosx-version-min=10.5 so it SHOULD be set up for 10.5... any ideas? thanks Editing an ancient question: I have the exact same problem on a different computer. This time I am at 10.5.8, fully update, the same executable works on 10.6 still. Has anyone had any luck with this in the months since I asked this?

  Read the article

• Displaying performance metrics in a modern web app?

  - by Charles

  We're updating our ancient internal PHP application at work. Right now, we gather extensive performance measurements on every pageview, and log them to the database. Additionally, users requested that some of the metrics be displayed at the bottom of the page. This worked out pretty well for us, because the last thing that the application does on every request is include the file containing the HTML footer. The updated parts of the application use an MVC framework and a Dispatch/Request/Response loop. The page footer is no longer the last thing done. In fact, it could very well be the first thing done, before the rest of the page is created. Because we can grab the Response before it's returned to the user, we could try to include placeholders for the performance metrics in the footer and simply replace them with the actual numbers, but this strikes me as a bad idea somehow. How do you handle this in your modern web app? While we're using PHP, I'm curious how it's done in a Ruby/Rails app, and in your favorite Python framework.

  Read the article

• How do I add the go language to gitg's list of viewable sources?

  - by Hotei

  Hoping a 'git' guru will help out here. I am just beginning to "git" for the first time and have (among other things :-) ) git and gitg installed from Ubuntu 10.4 / AMD64 distribution (ie. maybe not 'latest' version but not ancient). I am trying to look at the go code I've committed via gitg and in the "tree tab" it says :Cannot display file content as text. However, the "details tab" shows the diffs of the same file just fine. I know gitg's "tree tab" is working because I can use the tree view on *.c / *.html / *.txt etc just fine. Is there a way to tweak gitg into understanding that "*.go" is just text? A little more context: Installed gitg version is 0.0.5 - ie a version behind latest - 0.0.6 - source of which I am looking thru now. I do have a working /usr/share/gtksourceview-2.0/language-specs/ go.lang. It works just fine as highlighter in gedit. It appears that gitg may require displayable files to have a mime type of "text/plain", so I added that to go.lang No joy. gitg still fails on *.go I'm relatively sure the fix is simple, just don't know where to look.

  Read the article

• Flowcharting functional programming languages

  - by Sadface

  Flowcharting. This ancient old practice that's been in use for over 1000 years now, being forced upon us poor students, without any usefulness (or so do I think). It might work well with imperative, sequentially running languages, but what about my beloved functional programming? Sadly, I'm forced to create a flow chart for my programm (that is written in Haskell). I imagine it being easy for something like this: main :: IO () main = do someInput <- getLine let upped = map toUpper someInput putStrLn upped Which is just 3 sequenced steps, fetching data, uppercasing it, outputting it. Things look worse this time: main :: IO () main = do someInput <- fmap toUpper getLine putStrLn someInput Or like this: main :: IO () main = interact (map toUpper) Okay, that was IO, you can handle that like an imperative language. What about pure functions? An actual example: onlyMatching :: String -> [FilePath] -> [FilePath] onlyMatching ext = filter f where f name = lower ('.' : ext) == (lower . takeExtension $ name) lower = map toLower How would you flowchart that last one?

  Read the article

• Why Can't Businesses Upgrade their Browsers from IE6/IE7?

  - by viatropos

  I have read lots these past few weeks on IE6, seeing if it was really that bad to make it look right. I have just learned HTML and CSS this past year so I've been spoiled to start with basically CSS3 and HTML5, and I can do some really cool stuff super fast. I'm no IE6 master and I don't have years of experience with IE. So I thought it'd take a little time to figure out all the hacks to IE6/7 discovered and just implement them. But it's way harder than that (or maybe just way too much work). I'd have to either completely rebuild my design using "Internet Explorer 'Principles'", or cut out a lot of the neat things I could do using more recent technologies. For a million and one other reasons, everyone who builds things online seems to think IE should die. My question is, why can't businesses upgrade their browsers? When I work with businesses, they almost always resist the first time I ask, but 5 seconds later I'll show them what it looks like on my computer and talk about how great the latest stuff is (how much more secure later browser are, all the famous IE security cases, how much smoother and faster they new browsers are, how the IE team has basically missed the boat entirely, how much smoother business processes run, etc.), and they get excited! And within a few seconds they're up and running with Chrome or something. So can businesses not upgrade for some reasons? What are the reasons a business cannot upgrade? The main reason I think of is because they have an old version of windows. But a) wasn't there a legal case against this? and b) somebody must have figured out how to install Chrome or Firefox on ancient versions of Windows by now.

  Read the article

• C# cross thread dialogue co-operation

  - by John Attridge

  K I am looking at a primarily single thread windows forms application in 3.0. Recently my boss had a progress dialogue added on a separate thread so the user would see some activity when the main thread went away and did some heavy duty work and locked out the GUI. The above works fine unless the user switches applications or minimizes as the progress form sits top most and will not disappear with the main application. This is not so bad if there are lots of little operations as the event structure of the main form catches up with its events when it gets time so minimized and active flags can be checked and thus the dialog thread can hide or show itself accordingly. But if a long running sql operation kicks off then no events fire. I have tried intercepting the WndProc command but this also appears queued when a long running sql operation is executing. I have also tried picking up the processes, finding the current app and checking various memory values isiconic and the like inside the progress thread but until the sql operation finishes none of these get updated. Removing the topmost causes the dialog to disappear when another app activates but if the main app is then brought back it does not appear again. So I need a way to find out if the other thread is minimized or no longer active that does not involve querying the actual thread as that locks until the sql operation finishes. Now I know that this is not the best way to write this and it would be better to have all the heavy processing on separate threads leaving the GUI free but as this is a huge ancient legacy app the time to re-write in that fashion will not be provided so I have to work with what I have got. Any help is appreciated

  Read the article

< Previous Page | 4 5 6 7 8 9  | Next Page >