Search Results

Search found 407 results on 17 pages for 'ap'.

Page 8/17 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >

• How to configure a Router (TL-WR1043ND) to work in WDS mode?

  - by LanceBaynes

  I have a WRT160NL router (192.168.1.0/24 - OpenWrt 10.04) as AP. It's: - WAN port: connected to the ISP - WLAN: working as an AP, using 64 bit WEP/SSID: "MYWORKINGSSID", channel 5, using password: "MYPASSWORDHERE" - It's IP Address is: 192.168.1.1 Ok! It's working great! But: I have a TL-WR1043ND router that I want to configure as a "WDS". (My purpose is to extend the wireless range of the original WRT160NL.) Here is how I configure the TL-WR1043ND: 1) I enable WDS bridging. 2) In the "Survey" I select my already working network. 3) I set up the encryption (exact same like the already working one) 4) I choose channel 5 5) I type the SSID 6) I disable the DHCP server on it. After I reboot the router and connect to this router (TL-WR1043ND) over wireless I'm trying to ping google.com. From the ping I see that I can reach this router, that's ok, but it seems like that this router can't connect to the original one, the WRT160NL (so I don't get ping reply from Google). The encryption settings/password is good I checked it many-many-many times. what could be the problem? I'm thinking it could be a routing problem, but what should I add to the "Static Routing" menu? I tried to change the IP address of the TL-WR1043ND to: 192.168.1.2 So if this a routing issue then I should add a static routing rule that says: If destination: any then forward the packet to 192.168.1.1 p.s.: I updated the Firmware to the latest version. It's still the same. p.s.2: The HW version of the TL-WR1043ND is 1.8 p.s.3: Could that be the problem that I use different routers? (If I would buy.. another TL-WR1043ND and use it instead of the WRT160NL, and with normal Firmware, not OpenWrt, then it would work?? The "WDS" is different on different routers?) p.s.4: I will try to check the router logs@night - and paste it here! :\

  Read the article

• HP Procurve Issue Passing Multiple VLANs over a link

  - by MichaelRwat

  Just to start off with I am a Cisco guy that got placed into an HP project. Basic topology overview from outside in: ASA 5505 with two Ethernet connections to a 2910-24 port switch. This switch is then (Cisco Trunking) to a 2626 switch passing vlan (1 untagged and 100 tagged)between them. I created SVI's on each of the switches for both VLAN's for testing purposes. I can not get vlan 100 to pass across this link. I also have trunks configured to AP's off of the switch and can not ping the vlan 100 BVI on the AP's but can reach the vlan 1 BVI. Port 25 on Access layer (2626) connects (trunks) with port A1 of 2610. STP is not running at all on any switch (this is not my network I can't change this nor did I design this) Distribution Sw: MP1-0# show run ip default-gateway 10.100.100.100 vlan 1 name "DATA" untagged 1-22,24-A1,B1 ip address 10.100.100.6 255.255.255.0 no untagged 23 exit vlan 100 name "GUEST" untagged 23 tagged 24-A1 ip address 10.100.102.6 255.255.255.0 exit Access Sw: ip default-gateway 10.100.100.100 vlan 1 name "DEFAULT_VLAN" untagged 1-26 ip address 10.100.100.5 255.255.255.0 exit vlan 100 name "GUEST" ip address 10.100.102.5 255.255.255.0 tagged 15,25 exitt From the ASA I can ping the vlan 100 address of the 2610 but not the 2626 (10.100.102.6)[Not passing the "trunk"] If I plug into an access port vlan 100 of the 2626 I can ping the SVI for vlan 100 as intended. I can not ping across the "trunk" over vlan 100 but I can across vlan 1. There may be something obvious I'm missing but please review my configuration and thank you for the assistance.

  Read the article

• Macs don't connect to wifi access point but PCs will

  - by Josh

  So, as a side project I'm going to try and figure out why the wifi APs in my building exhibit the following behavior: - They typically allow all types of computers to connect without issues - Sometimes Apples can't get an IP address but will still connect to the AP's signal - Less often, PCs can't connect to the wifi (same as above - yes signal, no IP addy) - Don't let Raiders fans on no matter the time of day! My first thought was that the DHCP leases were all taken up when the Apples would try to connect, and it was just their unlucky timing, but I would then try to log on with a PC that had a new, unleased MAC address and it would work... Could this be something to do with interoperability between an apple wifi card, and the APs? Different parts of the DHCP lease being taken up first? The fact that the Seattle Mariners might actually be good this year?? If this hasn't used up everyone's patience (with my crappy sports jokes), something else I could use some help with: - We don't have the model or type of AP - This is because there is no documentation available for them, and they literally look like small white boxes with no writing on them. Also, the company that installed them is out of business, so the situation might be that no docs will ever be on the way. -- Do you guys have any ideas on how to figure out what we have? Thanks as always for all the help, and I'm looking forward to the day when I know enough to start contributing back to the site, Josh

  Read the article

• In an environment with multiple WiFi access points, do wireless clients sometimes connect to both at the same time?

  - by Bobby Burgess

  This is more of a curiosity than a problem, but in this new office I have two D-link DAP-2553's connected in a master/slave array (this just means the master keeps certain configuration options aligned with the slave). The network is set to 802.11n-only, and each AP has the same SSID and WPA2 key. The only difference is that they are on different channels (1 and 11). The WiFi network itself is working well. Users can roam around and the signal/speed is fairly consistent. However, I notice that when I look at the 802.11 client list in the web admin page for each of the 2 APs, I see that certain clients are connected to both, for extended periods of time, but I assume they are only passing data through one of them. Not every client is seen on each AP, but at any given time the same MAC address of a WiFi adapter can be associated (and remain associated) with both APs. The client list auto-refreshes every few seconds so I believe I'm looking at the most recent rather than stale information. One of the WiFi adapters that consistently associates with both APs is an Intel Centrino Wireless-N 1030 (laptop chip). Is it part of the WiFi standard that more than one association per WiFi card can be established concurrently on separate APS?

  Read the article

• System and Router configuration for setting up a home firewall based on Zentyal

  - by Ako

  I am not much of a system administrator, so please be patient if this looks too simple for you. I have a several computers at home, and all of them connect using an ADSL modem/router (and Wireless AP). I have been attacked several times (mainly from Russia and Ukraine), so I thought I should have some kind of firewall, besides the ESET firewall on my Windows 7. So now I have these (new) configuration: I have a small ADSL modem (Zyxel brand) which has only one Ethernet port. This modem is used to connect to internet and is configured in NAT mode. The interface has is configured with IP address 192.168.1.1. I have an old PC and I have installed zentyal on it. It has two Ethernet ports, eth0 and eth1. Eth0 is connected to the Zyxel modem with IP 192.168.1.2 and is checked as the WAN interface (external). I have another ADSL modem which is also a router with 4 Ethernet ports and Wireless AP. One of the Ethernet ports is connected to eth1 on Zentyal box. The Ethernet port's IP is 192.168.2.1 and Zentyal's eth1 is 192.168.2.2. Now, I want to enable other computers to connect to internet through the router both using Wireless and Ethernet. The problem is that I don't know how to configure the router so it routes connections to the Zentyal box. Does anyone have any clue? Again I am sorry if this looks stupid. Thanks.

  Read the article

• A router that supports connecting with 2 different wifi networks

  - by Allan Deamon

  I Have the following setup in one place: We have a small local ISP through wireless. I have a external parabolic antenna, connected to a external usb wifi radio, connected through USB to a desktop old PC. The pc connects do the ISP wiki network, then do a Dial Up (PPPoE) connection through the this wifi setup. This will expand with others mobiles devices to be used. When I need, I take my home wireless router and connect though Ethernet in the PC, which is shares the internet. The problem is that the PC must be always ON and working. I would like to buy a wireless router which could be an AP to the mobile devices, notebooks, etc, as also could connect to the ISP Wifi/PPPoE network. So, this device must: Have one radio with detachable antenna to connect to the external antenna. It must connect as client to a network and then dial up the PPP Have another radio serving as AP (infrastructure) to the local place This can't be very expensive. I found a candidate: ( http://www.tp-link.com/en/products/details/?categoryid=1682&model=TL-WR2543ND ) It have 3 deatachable antennas, working with dual band. Officially, his firmware doesn't support it. My supposition: If internally there is 3 or 2 distinct wlan ports (like wlan0, wlan1), and there is support, i could use a OpenWRT, DD-WRT or Tomato to make this works. It also have 1 USB port, which I cold use to connect my actual USB Wifi card on it instead to the old PC. Another alternative, is a router that can do this out of box, with the original firmware. But I don't think this is a easy thing to find.

  Read the article

• Is there a way to measure wifi traffic on a network from a client?

  - by millimoose

  Is there some way (preferrably one that comes with an existing tool) to measure the traffic going through the whole WiFi network from a computer connected to it? (That is, not from the AP or something between the modem and AP.) My situation is this: a few months back, the internet connection at my parent's place got really sluggish and laggy. (Lag spikes that cause page loads to time out etc, connections plain getting lost and dropping packets forever.) It's impossible to get mom's husband to do anything about this because he brushes this off with something like "just tell your sister to turn off torrents". Unfortunately the WiFi router's firmware doesn't do traffic logging. I'm not going to risk bricking it to put WRT on it; nor am I keen on rewiring the network to add a proxy to analyse the traffic. (I'm one of those people that make computers break just by looking at them, except machines I own.) I'd like to be able to find out roughly how much data is going over the air here while all the LAN wires are out of the router, all the computers accused of torrenting are off, etc. The idea is to either show that: Even if everything but my macbook is turned off, something is congesting the network. The husband is a systems developer and has a whole lot of mysterious hardware that's not to be touched around, one of them might be culprit. There is barely any traffic on the network, but the internet is still sluggish. Meaning this is likely a problem the ISP should solve. (Some hardware of theirs being glitchy, someone on an aggregated line hogging it constantly...) The network is encrypted, but I can temporarily set it to open for the sake of finding this out. So, in conclusion? Can this be done? Or is there some alternative way I could try to diagnose the problem?

  Read the article

• howto only tunnel specific hosts route through openvpn client on tomato

  - by kcome

  I am relatively newbie in networking world although I did coding and know some sysadmin background for a long time. and here I'm only one step from my destination. The whole picture is : at home I use one LinkSys E3000 as the gateway(don't know yet if this is it's name), wireless AP and no other routing/switching devices. It serves 1 PC and 1 Mac with LAN, 1 Mac Mini + 1 iPad + 2 smartphones with WIFI. My goal is use an openvpn client on the E3000 (with tomato firmware) and make my iPad and smartphone's all WiFi traffic through it, and other devices route remain the same non-openvpn route. So far I'm able to connect openvpn client on E3000 to an openvpn server, tunnel all my devices' all traffic through that openvpn connection. What's left is howto selectively route by source IP (at least in my guessing) to the tunnel while don't bother others. I had learned some 'iptables' and 'route' in past few days however without much luck, so here comes my question. Here are some info which will help you get the structure. ifconfig -a output, some useless lines striped, and in the web interface C0:C1:C0:1A:E0:28 is WAN, C0:C1:C0:1A:E0:27 is LAN, C0:C1:C0:1A:E0:29 is 2.4G wifi AP, C0:C1:C0:1A:E0:2A is 5G wifi AP. root@router:/tmp/home/root# ifconfig -a br0 Link encap:Ethernet HWaddr C0:C1:C0:1A:E0:27 inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr C0:C1:C0:1A:E0:27 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth1 Link encap:Ethernet HWaddr C0:C1:C0:1A:E0:29 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 eth2 Link encap:Ethernet HWaddr C0:C1:C0:1A:E0:2A UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host ppp0 Link encap:Point-to-Point Protocol inet addr:172.200.1.43 P-t-P:172.200.0.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING MULTICAST MTU:1480 Metric:1 vlan1 Link encap:Ethernet HWaddr C0:C1:C0:1A:E0:27 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 vlan2 Link encap:Ethernet HWaddr C0:C1:C0:1A:E0:28 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 wl0.1 Link encap:Ethernet HWaddr C0:C1:C0:1A:E0:29 BROADCAST MULTICAST MTU:1500 Metric:1 brctl show output root@router:/tmp/home/root# brctl show bridge name bridge id STP enabled interfaces br0 8000.c0c1c01ae027 no vlan1 eth1 eth2 before openvpn route-up script root@router:/tmp/home/root# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.200.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 172.200.0.1 0.0.0.0 UG 0 0 0 ppp0 openvpn server push PUSH: Received control message: 'PUSH_REPLY,redirect-gateway,dhcp-option DNS 8.8.8.8,route 172.20.0.1,topology net30,ping 10,ping-restart 120,ifconfig 172.20.0.6 172.20.0.5' openvpn's stock route-up script Apr 24 14:52:06 router daemon.notice openvpn[1768]: /sbin/ifconfig tun11 172.20.0.6 pointopoint 172.20.0.5 mtu 1500 Apr 24 14:52:08 router daemon.notice openvpn[1768]: /sbin/route add -net 72.14.177.29 netmask 255.255.255.255 gw 172.200.0.1 Apr 24 14:52:08 router daemon.notice openvpn[1768]: /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 172.20.0.5 Apr 24 14:52:08 router daemon.notice openvpn[1768]: /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 172.20.0.5 Apr 24 14:52:08 router daemon.notice openvpn[1768]: /sbin/route add -net 172.20.0.1 netmask 255.255.255.255 gw 172.20.0.5 route after openvpn root@router:/tmp/home/root# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.20.0.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun11 72.14.177.29 172.200.0.1 255.255.255.255 UGH 0 0 0 ppp0 172.200.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 172.20.0.1 172.20.0.5 255.255.255.255 UGH 0 0 0 tun11 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 172.20.0.5 128.0.0.0 UG 0 0 0 tun11 128.0.0.0 172.20.0.5 128.0.0.0 UG 0 0 0 tun11 0.0.0.0 172.200.0.1 0.0.0.0 UG 0 0 0 ppp0 something I had noticed and tried: * on the web interface of openvpn client there is an option "Create NAT on tunnel", if i check this, there is the following script (probably executed after openvpn connection established) root@router:/tmp/home/root# cat /tmp/etc/openvpn/fw/client1-fw.sh #!/bin/sh iptables -I INPUT -i tun11 -j ACCEPT iptables -I FORWARD -i tun11 -j ACCEPT iptables -t nat -I POSTROUTING -s 192.168.1.0/255.255.255.0 -o tun11 -j MASQUERADE if i uncheck this option, the last line will not appear. Then I guess probably the my issue will be solved by iptables and NAT related commands, I just haven't got enough knowledge to figure them out. I tried run iptables -t nat -I POSTROUTING -s 192.168.1.6 -o tun11 -j MASQUERADE manually after openvpn connected (192.168.1.6 is the ip address of my iPad), then my iPad get internet with openvpn tunnel, however all other devices can't reach internet. in case if needed, here is the iptables about NAT root@router:/tmp/home/root# iptables -t nat -L -n Chain PREROUTING (policy ACCEPT) target prot opt source destination DROP all -- 0.0.0.0/0 192.168.1.0/24 WANPREROUTING all -- 0.0.0.0/0 172.200.1.43 upnp all -- 0.0.0.0/0 172.200.1.43 Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- 0.0.0.0/0 0.0.0.0/0 SNAT all -- 192.168.1.0/24 192.168.1.0/24 to:192.168.1.1 Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain WANPREROUTING (1 references) target prot opt source destination DNAT icmp -- 0.0.0.0/0 0.0.0.0/0 to:192.168.1.1 Chain upnp (1 references) target prot opt source destination DNAT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:5353 to:192.168.1.3:5353 Thanks in advance for helping and read this so much, I hope i made every info you need to give a help :)

  Read the article

• Using 3G/UMTS in Mauritius

  After some conversation, threads in online forum and mailing lists I thought about writing this article on how to setup, configure and use 3G/UMTS connections on Linux here in Mauritius. Personally, I can only share my experience with Emtel Ltd. but try to give some clues about how to configure Orange as well. Emtel 3G/UMTS surf stick Emtel provides different surf sticks from Huawei. Back in 2007, I started with an E220 that wouldn't run on Windows Vista either. Nowadays, you just plug in the surf stick (ie. E169) and usually the Network Manager will detect the new broadband modem. Nothing to worry about. The Linux Network Manager even provides a connection profile for Emtel here in Mauritius and establishing the Internet connection is done in less than 2 minutes... even quicker. Using wvdial Old-fashioned Linux users might not take Network Manager into consideration but feel comfortable with wvdial. Although that wvdial is primarily used with serial port attached modems, it can operate on USB ports as well. Following is my configuration from /etc/wvdial.conf: [Dialer Defaults]Phone = *99#Username = emtelPassword = emtelNew PPPD = yesStupid Mode = 1Dial Command = ATDT[Dialer emtel]Modem = /dev/ttyUSB0Baud = 3774000Init2 = ATZInit3 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0Init4 = AT+cgdcont=1,"ip","web"ISDN = 0Modem Type = Analog Modem The values of user name and password are optional and can be configured as you like. In case that your SIM card is protected by a pin - which is highly advised, you might another dialer section in your configuration file like so: [Dialer pin]Modem = /dev/ttyUSB0Init1 = AT+CPIN=0000 This way you can "daisy-chain" your command to establish your Internet connection like so: wvdial pin emtel And it works auto-magically. Depending on your group assignments (dialout), you might have to sudo the wvdial statement like so: sudo wvdial pin emtel Orange parameters As far as I could figure out without really testing it myself, it is also necessary to set the Access Point (AP) manually with Orange. Well, although it is pretty obvious a lot of people seem to struggle. The AP value is "orange". [Dialer orange]Modem = /dev/ttyUSB0Baud = 3774000Init2 = ATZInit3 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0Init4 = AT+cgdcont=1,"ip","orange"ISDN = 0Modem Type = Analog Modem And you are done. Official Linux support from providers It's just simple: Forget it! The people at the Emtel call center are completely focused on the hardware and Mobile Connect software application provided by Huawei and are totally lost in case that you confront them with other constellations. For example, my wife's netbook has an integrated 3G/UMTS modem from Ericsson. Therefore, no need to use the Huawei surf stick at all and of course we use the existing software named Wireless Manager instead of. Now, imagine to mention at the help desk: "Ehm, sorry but what's Mobile Connect?" And Linux after all might give the call operator sleepless nights... Who knows? Anyways, I hope that my article and configuration could give you a helping hand and that you will be able to connect your Linux box with 3G/UMTS surf sticks here in Mauritius.

  Read the article

• Filtering documents against a dictionary key in MongoDB

  - by Thomas

  I have a collection of articles in MongoDB that has the following structure: { 'category': 'Legislature', 'updated': datetime.datetime(2010, 3, 19, 15, 32, 22, 107000), 'byline': None, 'tags': { 'party': ['Peter Hoekstra', 'Virg Bernero', 'Alma Smith', 'Mike Bouchard', 'Tom George', 'Rick Snyder'], 'geography': ['Michigan', 'United States', 'North America'] }, 'headline': '2 Mich. gubernatorial candidates speak to students', 'text': [ 'BEVERLY HILLS, Mich. (AP) \u2014 Two Democratic and Republican gubernatorial candidates found common ground while speaking to private school students in suburban Detroit', "Democratic House Speaker state Rep. Andy Dillon and Republican U.S. Rep. Pete Hoekstra said Friday a more business-friendly government can help reduce Michigan's nation-leading unemployment rate.", "The candidates were invited to Detroit Country Day Upper School in Beverly Hills to offer ideas for Michigan's future.", 'Besides Dillon, the Democratic field includes Lansing Mayor Virg Bernero and state Rep. Alma Wheeler Smith. Other Republicans running are Oakland County Sheriff Mike Bouchard, Attorney General Mike Cox, state Sen. Tom George and Ann Arbor business leader Rick Snyder.', 'Former Republican U.S. Rep. Joe Schwarz is considering running as an independent.' ], 'dateline': 'BEVERLY HILLS, Mich.', 'published': datetime.datetime(2010, 3, 19, 8, 0, 31), 'keywords': "Governor's Race", '_id': ObjectId('4ba39721e0e16cb25fadbb40'), 'article_id': 'urn:publicid:ap.org:0611e36fb084458aa620c0187999db7e', 'slug': "BC-MI--Governor's Race,2nd Ld-Writethr" } If I wanted to write a query that looked for all articles that had at least 1 geography tag, how would I do that? I have tried writing db.articles.find( {'tags': 'geography'} ), but that doesn't appear to work. I've also thought about changing the search parameter to 'tags.geography', but am having a devil of a time figuring out what the search predicate would be.

  Read the article

• Ruby array index method not working returning NIL value

  - by Rails beginner

  Here is the error: => ["Mænd med navnet Kim", "30.094", "29.946", "-148", "Kvinder med navnet Kim", "341", "345", "4", "Mænd med navnet Kim Hansen", "1.586", "1.573", "-13", "Kvin der med navnet Kim Hansen", "5", "5", "0", "Mænd og kvinder med efternavnet Hans en", "226.040", "223.478", "-2.562"] irb(main):094:0> irb(main):095:0* @tester.index("Mænd med navnet Kim") => nil irb(main):096:0> @tester.index("Kvinder med navnet Kim") => 4 irb(main):097:0> @tester.index("Mænd med navnet Kim Hansen") => nil irb(main):098:0> @tester.index("Kvinder med navnet Kim Hansen") => 12 irb(main):099:0> @tester.index("Mænd og kvinder med efternavnet Hansen") => nil irb(main):100:0> Example tried Gsub method: <ap(&:text).map{|d| d.delete "'"}.map{|d| d.gsub("æ", "#844"} irb(main):113:1> ) SyntaxError: (irb):112: syntax error, unexpected '}', expecting ')' from C:/Ruby193/lib/ruby/gems/1.9.1/gems/railties-3.0.9/lib/rails/comman ds/console.rb:44:in `start' from C:/Ruby193/lib/ruby/gems/1.9.1/gems/railties-3.0.9/lib/rails/comman ds/console.rb:8:in `start' from C:/Ruby193/lib/ruby/gems/1.9.1/gems/railties-3.0.9/lib/rails/comman ds.rb:23:in `<top (required)>' from script/rails:6:in `require' from script/rails:6:in `<main>' <ap(&:text).map{|d| d.delete "'"}.map{|d| d.gsub("æ", "#844")} Encoding::CompatibilityError: incompatible encoding regexp match (CP850 regexp w ith UTF-8 string) from (irb):114:in `gsub' from (irb):114:in `block in irb_binding' from (irb):114:in `map' from (irb):114 from C:/Ruby193/lib/ruby/gems/1.9.1/gems/railties-3.0.9/lib/rails/comman ds/console.rb:44:in `start' from C:/Ruby193/lib/ruby/gems/1.9.1/gems/railties-3.0.9/lib/rails/comman ds/console.rb:8:in `start' from C:/Ruby193/lib/ruby/gems/1.9.1/gems/railties-3.0.9/lib/rails/comman ds.rb:23:in `<top (required)>' from script/rails:6:in `require' from script/rails:6:in `<main>'

  Read the article

• implement SIMD in C++

  - by Hristo

  I'm working on a bit of code and I'm trying to optimize it as much as possible, basically get it running under a certain time limit. The following makes the call... static affinity_partitioner ap; parallel_for(blocked_range<size_t>(0, T), LoopBody(score), ap); ... and the following is what is executed. void operator()(const blocked_range<size_t> &r) const { int temp; int i; int j; size_t k; size_t begin = r.begin(); size_t end = r.end(); for(k = begin; k != end; ++k) { // for each trainee temp = 0; for(i = 0; i < N; ++i) { // for each sample int trr = trRating[k][i]; int ei = E[i]; for(j = 0; j < ei; ++j) { // for each expert temp += delta(i, trr, exRating[j][i]); } } myscore[k] = temp; } } I'm using Intel's TBB to optimize this. But I've also been reading about SIMD and SSE2 and things along that nature. So my question is, how do I store the variables (i,j,k) in registers so that they can be accessed faster by the CPU? I think the answer has to do with implementing SSE2 or some variation of it, but I have no idea how to do that. Any ideas? Thanks, Hristo

  Read the article

• Bad performance function in PHP. With large files memory blows up! How can I refactor?

  - by André

  Hi I have a function that strips out lines from files. I'm handling with large files(more than 100Mb). I have the PHP Memory with 256MB but the function that handles with the strip out of lines blows up with a 100MB CSV File. What the function must do is this: Originally I have the CSV like: Copyright (c) 2007 MaxMind LLC. All Rights Reserved. locId,country,region,city,postalCode,latitude,longitude,metroCode,areaCode 1,"O1","","","",0.0000,0.0000,, 2,"AP","","","",35.0000,105.0000,, 3,"EU","","","",47.0000,8.0000,, 4,"AD","","","",42.5000,1.5000,, 5,"AE","","","",24.0000,54.0000,, 6,"AF","","","",33.0000,65.0000,, 7,"AG","","","",17.0500,-61.8000,, 8,"AI","","","",18.2500,-63.1667,, 9,"AL","","","",41.0000,20.0000,, When I pass the CSV file to this function I got: locId,country,region,city,postalCode,latitude,longitude,metroCode,areaCode 1,"O1","","","",0.0000,0.0000,, 2,"AP","","","",35.0000,105.0000,, 3,"EU","","","",47.0000,8.0000,, 4,"AD","","","",42.5000,1.5000,, 5,"AE","","","",24.0000,54.0000,, 6,"AF","","","",33.0000,65.0000,, 7,"AG","","","",17.0500,-61.8000,, 8,"AI","","","",18.2500,-63.1667,, 9,"AL","","","",41.0000,20.0000,, It only strips out the first line, nothing more. The problem is the performance of this function with large files, it blows up the memory. The function is: public function deleteLine($line_no, $csvFileName) { // this function strips a specific line from a file // if a line is stripped, functions returns True else false // // e.g. // deleteLine(-1, xyz.csv); // strip last line // deleteLine(1, xyz.csv); // strip first line // Assigna o nome do ficheiro $filename = $csvFileName; $strip_return=FALSE; $data=file($filename); $pipe=fopen($filename,'w'); $size=count($data); if($line_no==-1) $skip=$size-1; else $skip=$line_no-1; for($line=0;$line<$size;$line++) if($line!=$skip) fputs($pipe,$data[$line]); else $strip_return=TRUE; return $strip_return; } It is possible to refactor this function to not blow up with the 256MB PHP Memory? Give me some clues. Best Regards,

  Read the article

• Looking for home networking hardware and software advice

  - by phobos7

  Note: I originally wrote this up in a blog post. I've removed any affiliate links that I put in my original post to ensure I don't annoy anybody. I've recently moved home and I now need to go to the trouble of sorting out my home network yet again. We had Virgin broadband in Hertford but you can't get Virgin in the street we've moved to so I've had to go with O2 Broadband. Normally I prefer to use my own hardward, and previously used the DLink DIR-655 router which was great, but in this situation I am using the O2 Wirelss Box III since I only have an old Netgear DG834PN Wireless G modem router and I'd rather be using Wireless N. Anyway, the place we have moved into has only one phone point in the hallway, has the best TV point in one room and the best place to put the TV and other entertainment stuff in yet another room. So, networking the house up for Internet and TV is required. The diagram below shows the things that I'll have in my home network but there are three points where I'm not quite sure what hardware to us. Wireless Access Point/Bridge, that acts only as a wireless to wire bridge and not an AP, that links up a Media Centre/PC and a couple of consoles to the network. I'm pretty much settled on us an Acer Aspire Revo R3600 as my media PC, probably with Ubuntu or Windows and XBMC installed. Wireless Access Point/Bridge, that acts only as a wireless to wire bridge and not an AP, that links up a device that can decode and stream TV from a TV aerial across the network. The device that is connected to 2). At the moment I'm considering a HDHomeRun by SiliconDust. At the moment I'm considering either the TP LINK TL-WA701ND 150Mbps Wireless Lite N Access Point (very cheap at Amazon) or the Netgear 5 GHz Wireless-N HD Access Point/Bridge. I'd love to get some insight into what you would do in my situation. What Wireless Access Point/Bridge should I put at points 1) and 2)? What device should I choose for point 3) that can decode and stream a TV signal? Is the Acer Aspire Revo R3600 a good choice? ![alt text][6] Note 2: I've also posted this question on AVForums.

  Read the article

• Proxying webmin with nginx

  - by TheLQ

  I am attempting to proxy webmin behind nginx for various reasons that are outside the scope of this question. However I've been trying for a while now and can't seem to figure it out and think I'm to the point where I've exhausted all the permutations of the config file I can think of. What I have now: relevant nginx config (commented out options removed, I tried many) # Proxy for webmin location /admin/quackwall-webmin { proxy_pass http://127.0.0.1:10000; # Also tried ending with /admin/quackwall-webmin proxy_set_header Host $host; } /etc/webmin/config - Relevant parts webprefix=/admin/quackwall-webmin webprefixnoredir=1 referer=(nginx domain name) Webmin itself is on the standard ports, listening on all addresses temporarily for debugging. SSL has been disabled for right now. So I make a standard request for the login page. However all the CSS and images are broken, with the standard login page returned for all of the resources. In the webmin miniserv logs I see 127.0.0.1 - - [29/Oct/2012:12:29:00 -0400] "GET /admin/quackwall-webmin/session_login.cgi HTTP/1.0" 401 2453 127.0.0.1 - - [29/Oct/2012:12:29:01 -0400] "GET /admin/quackwall-webmin/unauthenticated/style.css HTTP/1.0" 401 2453 127.0.0.1 - - [29/Oct/2012:12:29:01 -0400] "GET /admin/quackwall-webmin/unauthenticated/sorttable.js HTTP/1.0" 401 2453 127.0.0.1 - - [29/Oct/2012:12:29:01 -0400] "GET /admin/quackwall-webmin/unauthenticated/toggleview.js HTTP/1.0" 401 2453 So all the URL's are returning 401s. Interestingly ngrep seems to show that the requests suceeded on the backend communication between nginx and webmin T 127.0.0.1:58908 -> 127.0.0.1:10000 [AP] POST /admin/quackwall-webmin/session_login.cgi HTTP/1.0..Host: (host)..Connection: close..User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW 64; rv:16.0) Gecko/20100101 Firefox/16.0..Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8..Accept-Language: en-US,en;q=0.5. .Accept-Encoding: gzip, deflate..Referer: http://(host)/admin/quackwall-webmin/session_login.cgi..Cookie: testing=1..Cache-Control: ma x-age=0..Content-Type: application/x-www-form-urlencoded..Content-Length: 41....page=%2F&user=(user)&pass=(pass) T 127.0.0.1:10000 -> 127.0.0.1:58908 [AP] HTTP/1.0 200 Document follows.. Various other permutations of these config options and others show similar results, with the URL sent to webmin by nginx either being /admin/quackwall-webmin/session_login.cgi, /admin/quackwall-webmin//session_login.cgi, and just /session_login.cgi. All give 201 Unauthenticated responses. All requests, even those that somewhat succeed (as in I can actually load the resources of the page) Is changing the webprefix in webmin even supported? What am I doing wrong? What else can I try?

  Read the article

• Could a HomePlug be used to connect 2 routers?

  - by tigermain

  I have 2 routers that I would like to connect together (they are wireless but dont have an AP mode) could I simply buy a pair of homeplugs and connect them in order for all machines to have complete visibility of each other?! The DHCP will only be enabled on one, so the other will simply be acting as a switch

  Read the article

• Why is my amazon EC2 in asian pacific region having a US ip address?

  - by Turner

  I recently give a free trial to amazon EC2 service, I created a free tier micro instance(AMI is windows server 2008) in the Asian Pacific(Tokyo) region, but when it's done the public DNS it provided is ec2-54-238-181-35.ap-northeast-1.compute.amazonaws.com. The corresponding IP is 54.238.181.35, which I think is in the U.S. I tried to allocate some more elastic IPs but all of them seem to have a U.S. origin. Anyone please help explain to me ?

  Read the article

• WPA Connection problem

  - by Renjith G

  hi , I am using hostapd,wireless tools with madwifi for my wireless ap in my board. The WEP, WPA-PSK connections and communications between my board and my desktop PC, WINDOWS XP SP2) (with OLITEC wireless usb)are fine. But when i configured the WPA type, connection established but it is showing the status in the secuirity dialog box "TKIP - Key Absent" Can any one faced this problem?? /renjith g

  Read the article

• Appropriate USB enclosure to use with an Ultra ATA drive

  - by Topdown

  I have a friend with a broken iBook, but we wish to recover the hard disk. I haven't seen the drive itself, however the spec lists it as an "Ultra ATA drive". Could you please advise if this is 100% compatible with any standard USB IDE 2.5inch enclosure? Full spec: iBook 12" 1GHz(AP) 256MB DDR266 SDRAM built-in Keyboard/Mac OS X Bluetooth Module 40GB Ultra ATA drive Combo (DVD-ROM/CD-RW).

  Read the article

• How can i configure country code in wireless WEP communication?

  - by Renjith G

  hi I need to configure country code between my wireless communication points. I am using madwifi, wireless tools and hostapd set up in my ap(board- linux OS(2.6.10)) , and am using OLITEC stick usb 802.11g card in my windows machine. I can communicate successfully using WEP,WPA-PSK and WPA , but i need to configure some more additional options such as Country code and Beacon period and Beacon interval etc. Expecting the reply, /renjith g

  Read the article

• Enabling UDMA Mode 6 for a SATA II HDD

  - by shadeMe

  How would I go about enabling UDMA Mode 6 transfer for my Seagate Baracudda 7200.12 HDD ? HD tune tells me that it supports it but is operating at Mode 5. My motherboard is a ASUS P5B-MX WiFi/AP, uses the ICH7 chipset ( if I recall correctly ). I'm running Windows 7 x64.

  Read the article

• How do I get the IP address of a switch.

  - by Atilla Filiz

  I have a wireless AP+switch which I configured years ago, before moving, and haven't used for a while. Now I want to reconfigure it for my new network, but have no idea what I set as its IP address(It was probably something 192.168.xx.yy). What is the best way for discovering its IP? A script to spam the whole address space?

  Read the article

• Could a HomePlug be used to connect 2 routers?

  - by tigermain

  I have 2 routers that I would like to connect together (they are wireless but dont have an AP mode) could I simply buy a pair of homeplugs and connect them in order for all machines to have complete visibility of each other?! The DHCP will only be enabled on one, so the other will simply be acting as a switch

  Read the article

• Why is my SSH session timing out in less than a minute?

  - by John Smith

  Within a minute of connecting to my remote Linux server through SSH, my session times out and I cannot contact the server until a few seconds have passed. Meanwhile, I'm connected to other servers without interruption. This is only happening when I establish connection from an hotel wireless AP. When I connect from my phone's Internet, the problem does not occur. Does anyone know what might be causing these unusual timeouts?

  Read the article

• Is there a way to setup a hotspot with a domain name rather than IP address?

  - by WagnerMatosUK

  Basically I've setup a hotspot and its currently being accessed through an IP address. I'd like to use a hostname instead. This is for internal use only, meaning the ODROID device which is being used to as Access Point is connected to the internet via ethernet and only a few devices will access the AP. My setup details: Arch Linux on an ODROID U3 device, using hostapd and dhcp server. PS: I'm quite inexperienced with network so I might be missing something obvious here. Thanks in advance

  Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >