Search Results

Search found 193 results on 8 pages for 'athlon'.

Page 8/8 | < Previous Page | 4 5 6 7 8 

• Possible capacitor plague - need help identifying

  - by cornjuliox

  I've been having some PC power issues lately, and I think I've tracked it down to a bad power supply. Lately, when I'm on my PC it will often restart without warning, displaying "Hypertransport sync flood error occurred last boot." once POST finishes. I've googled the error, but can't come to a definitive conclusion as to what's causing it. I've seen posts suggesting that it might be a power supply issue, but nothing conclusive. Here's what I've done so far: -I haven't installed anything suspect within the last 3 months. -I do overclock just a tiny bit, so I tried raising the voltages a little. That didn't work so I brought both CPU multiplier and voltages all back to their default settings, but that didn't solve the problem either. The problem still occurs. -AV scanned the whole system, nothing suspect. -I suspected that it might be a bad power supply so I cracked that open and found the following: I think it might be cap plague, but I'm not sure. It looks more like glue TBH. Could someone help me figure out what might be wrong with this PC? EDIT: Sometimes, after these restarts, I noticed that the GPU fan doesn't spin up, and the single rear case fan that just happens to be connected to the same molex Y-cable as the GFX card doesn't spin up either. Anything to that? EDIT 2: I do use the system quite heavily, but I don't know how that will factor into this. I often play Diablo 3 and EVE Online at the same time, frequently alt-tabbing between the two. I also have Firefox open in the background, sometimes with several tabs, and if I feel like it, I'll mute the in-game sound and open foobar2000 for better music. Could it be that I'm just pushing this thing too hard? EDIT 3: I also noticed something odd. Right before I experience these restarts, my monitor would suffer from very faint lines of static moving across the screen. The monitor is still very much useable, but it is very annoying. Following the restart it disappears, and then would gradually re-appear over the next few days, and then restarts again. I find it to be very odd. System specs for good measure: Orion 600 W PSU AMD Athlon II X3 440 (overclocked to 3.14 ghZ, raised the CPU multiplier to x13 from x10) MSI G40-775 motherboard 1 GB inno3D GTX 550 ti 4 GB DDR3 RAM 500 GB Samsung SATA HD

  Read the article

• Computer freezes +/- 30 seconds, suspicion on SSD

  - by Robert vE

  My computer freezes for about 30 seconds, this happens occasionally. When it happens I can still move the mouse, sometimes even alternate between tabs in google chrome. If I try to open windows explorer nothing happens. Also chrome rapports "waiting for cache". It also happens in starcraft II, during which the sounds loops. I have made a Trace as this topic describes: How do I troubleshoot a Windows 7 freeze or slowness? Trace: https://docs.google.com/open?id=0B_VkKdh535p6NklhSDdBLURUMnc I have looked at it, but I couldn't figure it out. My system specs are: AMD Athlon X4 651 Asus Ati HD6670 ADATA SSD sp900 Asus f1a55 mainboard 4 GB crucial 1333 ram 500 watt atx ps I'm running Windows 7, fully updated. Any help is much appreciated. Update: I tried something before your reply that may have helped the problem. I don't know for sure if it has, it's too soon to tell. A bit of history first. I had problems installing win7 on my ssd from the start. In IDE mode it worked, but I had the same problems as above. AHCI was a total fail, with it on before install as well as turning it on after install (including tweaking register). I didn't bother installing the AMD chipset/AHCI as it was reported to have no TRIM function and thus make problems worse. Eventually I did install the AMD SMbus driver as the stability issues were driving me crazy. It worked, no more issues, until I installed some extra drivers and software. Audio/LAN/ASUS suite, I don’t see the relation, but somehow it screwed up my system again. As a last effort I posted here on this site. After which the thought occurred to me turn on AHCI again as by now I had all necessary drivers installed anyway. (plus all windows updates downloaded/installed in the meantime) I did and stability didn’t seem great the first few reboots, but eventually everything seemed to work great. I tried to play starcraft II – an almost guaranteed freeze before – and I had no problems. I’m basically crossing my fingers and hope the problem is gone for good. I still think it has something to do with my SSD. In my research into the problem I noticed a lot of these issues with sandforce 2281 firmware, the exact same firmware I have. People reported the same problem that I had, freezes. Additionally they reported that during a freeze the hdd light stayed on, I noticed after I read this that this happened with my computer as well. None of this is conclusive evidence that my SSD is really to fault, but it is suspicious. And why turning on AHCI would fix it I don’t know. Thank you Tom for taking a look, if the problem returns I will certainly do what you advised.

  Read the article

• Windows Server 2003 Standard R2 CD 1 cannot boot: freeze at No Emulation

  - by TGP1994

  Hi everyone. I've been interested in the Windows Server line of OSes, so since I apply for DreamSpark, I thought I'd go download it and try it. I just so happened to have an old desktop that I was using awhile ago for Windows XP, so I imaged the drive in preparation for it to be overwritten with the new OS. (This system has an Asus A7V8X-X motherboard, an AMD Athlon XP 2800+ processor, and 1GB of RAM.) I tried burning the first disk image on my newer desktop computer, running Windows XP, although the CD burner consistently failed at a particular track area from cd to cd, so it seemed like the burner was toast there. Fortunately, I had a laptop, so I transferred the images over to that, then burned the first disc there. First time around went great, and the burning program reported no errors. I then took the CD over to the computer that I was intending to install Server onto, set the BIOS to boot from the CD drive, then I booted it up. Like normal, after the POST, it printed "Boot from ATAPI CD-Rom: No Emulation", which I was used to seeing with bootable cds. I waited for the "Press any key to continue..." message that I had become so familiar with in windows discs, although I saw none. The computer sat there for about 5 seconds with the cd spinning, then it spun down like it was done reading it. Nothing else happened. No response from the keyboard. I tried again, same result. I then downloaded IMGBurn, and I put the burned cd into the laptop that burned it originally. I also downloaded a fresh image from the dreamspark site. I ran a verify session, and everything checked out. I later tried getting various DOS startup discs, then I tried booting the winnt binary, which supposedly initiates the installation process. Either the shells reported that not enough memory was available (since they would be running in low memory mode), or FreeDOS in particular would report Illegal instructions right away. Is the image corrupt at dreamspark, or am I doing something wrong?

  Read the article

• What are the most likely bottlenecks determining the performance of CamStudio screen recording?

  - by Steve314

  When doing screen recording, I can get a frame rate of maybe 15 frames per second for the full screen on my 1080p monitor using the XVID codec. I can increase the speed a bit by recording a region, changing screen modes, and tweaking other settings, but I'm curious what hardware upgrades might give me the biggest bang for my buck. My PC is budget, but modern... Athlon 2 X4 645 (3.1GHz, quad core, limited cache) processor. 4GB single channel DDR3 1066 RAM. ASRock motherboard with NVidia GeForce 7025/nForce 630a Chipset. ATI Radeon HD 5450 graphics card - 512MB on board, not configured to steal system RAM. I dual-boot Windows XP and Windows 7. For the moment, XP is my bigger performance concern as it's still my getting-things-done O/S as opposed to my browser-host O/S. My goal is to make a few programming-related tutorials. For a lot of that I don't need screen recording - I can make up some slides, record audio with the PC switched off, yada yada. When I do need screen recording, I'll mostly be recording Notepad++, Visual Studio or a command prompt. Occasionally, I may be recording some kind of graphics or diagram program and using my pre-Bamboo cheap Wacom tablet - I have the CS2 versions of Photoshop and Illustrator, but I'd much more likely be using Microsoft Paint. Basically, what I'll be recording won't be making huge demands on the machine - but recording a fair number of pixels (720p preferred) will be useful. What's particularly wierd - not so long ago I still had a five-year-old Pentium 4 based PC. And (with the same 1080p monitor) it could record at not far from the same frame rate. So clearly the performance issues are more subtle than just throw-money-at-it. My first guess would be that the main bottleneck is the bandwidth for transferring data to/from the graphics card. Is that likely to be correct? In support of that, see this [Radeon HD 5450 review][1] - the memory bandwidth is only 12.8 GB/s. If you can't get data out of graphics memory quickly, you can't transfer it back to the system memory quickly. Apparently, that's slower than some top-end cards in 2002.

  Read the article

• A Windows Update Prevented Live Discs From Working?

  - by user88311

  First off I'll state my system specs. Acer Aspire M1100 Windows Vista Home Basic 32bit OEM 2 Gigs of DDR2 ram 160Gig hard drive 2.7Ghz AMD Athlon 64 processor ATI Radeon X1250 Graphics card A few days ago my computer did automatic updates and updated windows defender to KB915597 (Definition 1.135.415.0), After which when shutting down and starting up I would receive BSOD with the information BUGCODE_USE_DRIVER and 0x000000FE (0x00000008, 0x00000006, 0x00000006, 0x877330000) upon where my computer would not start up with any USB devices plugged in and it always require me to run startup repair before it started. Upon when I first started it up and was able to fully boot windows, I had no use of the mouse so I was unable to install the fix that the windows solutions center brought up on my screen, so I restarted again and installed the fix hoping it would cease the problem, it did not. Upoon starting up after installing the fix and restarting I was confronted with the BSOD 0x000000FE (0x00000008, 0x00000006, 0x00000006, 0x83291000) at which I found the startup repair could not fix the problem and I restored, as I most like should have in the first place. After going through that I read that simply installing the latest defender version from the microsoft site had fixed this problem for others, so I did that, to find I still received the BSOD's. So in a attempt to find a fix to the problem I went to the microsoft answers site to try to find a way to fix the problem, there I was told to simply disable defender and reboot to see if that fixed the problem, upon doing this my computer would no longer even startup, when I boot normally I get to just when the loading screen finishes and then my computer restarts and when I run startup repair, it runs for about 15 seconds and then my computer restarts as well. I have tried running ubuntu live discs in order to simply access the drive and simply copy and paste the 2 month old physical backup I have of my C drive to the C drive, but whenever I run the live OS when it gets to the end of the load screen and is about to boot, the computer again restarts, yet if I put in a gparted disc, I am able to boot it fully, although it does not give me access to the file system just partition managing and when I attempt to access the internet through it, the computer once again restarts. So my question is, how could the update and what has happened prevent me from running the live OS's properly?

  Read the article

• Xobni Plus for Outlook [Review]

  - by The Geek

  Overview Xobni Plus is an addin that will bring a sidebar to Outlook which allows you to search through your inbox and contacts a lot easier. It provides the ability to search and keep track of your favorite social networks. Searching with Xobni is a lot more powerful than the default search feature in Outlook. It let’s you drill down your searches to conversations, email, links, and attachments. It now supports Outlook 2010 both 32 & 64-bit versions. Installation & Setup Installation is easy following the wizard. After completing the wizard you can tell you’re friends on Facebook and Twitter that you are now using it. You can also decide to join their Product Improvement Program if you want. After installation when you open Outlook, Xobni appears as a sidebar on the right side. Don’t worry about it always being in the way, as you can hide it if you need more room for other Outlook functions. After Xobni free is installed, you can upgrade to the Plus version at any time. A new window will open up and you can use your Credit Card, PayPal, or redeem a code if you have one. Features & Use Where to begin with the amount of features available in Xobni Plus? It really has an amazing amount of cool features. Of course you’ll have all of the features of the Free Version which we previously covered…and a lot more. After Xobni is installed you’ll notice a section for it on the Ribbon. From here you can search Xobni, show or hide the Sidebar, and change other options. It allows you to easily keep up with various social networks like Facebook, Twitter, and LinkedIn… Check out email analytics and contact ranks. Click on the Files Exchanged tab to search for specific attachments. Quickly search links exchanged with your contacts. Hover over a link to get a preview of what it entails. It gives you the ability to index all of your Yahoo mail as well, without the need for purchasing Yahoo Plus! Then your Yahoo messages appear in the Xobni sidebar. When you select a contact you can see related messages from you Yahoo account. Easily index all of your mail…including Yahoo mail for better organization and faster search results. There are several options you can select to change the way Xobni works. From setting up your Yahoo email, Indexing options, and much more. Additional Features of Xobni Plus Advanced Search Capabilities – Filter results, Boolean & Phrase Search, Ability to search Appointments & Tasks, Advanced Search Builder Search unlimited PST data files Xobni contacts in the compose screen Find links exchanged with your contacts View calendar appointments One year premium tech support No Ads! Performance We ran Xobni Plus on Outlook 2010 32-bit on a Dual-Core AMD Athlon system with 4GB of RAM and found it to run quite smoothly. However, we did notice it would sometimes slow down launching Outlook, especially if other apps are running at the same time. Product Support When you buy a license for Xobni Plus you get a full year of premium tech support. They provide a Questions and Answers page on their site where you can run a search query and answers appear instantly. You can contact support directly as a Plus member through their web form and they advise the turn around time is 2 business days. However, when we tested it, we received a response within 24 hours. They also provide FAQ, Community forum, and you can download the Owners Manual in PDF format from the support page. Conclusion Xobni Plus is a very powerful addin for Outlook and includes a lot more features that we didn’t cover in this review. You can download Xobni free edition which includes an 8 day free trial of the Plus version. This provides a good way to start getting familiar with it. Then upgrade to Xobni Plus at any time for $29.95. Once you get started, you’ll find the sidebar is nicely laid out and intuitive to use. If you live out of Outlook during the day, Xobni Plus is a great addition for fast and powerful searches. It provides an easy way to keep all of your contacts and messages well organized and easy to find. Xobni Plus works with XP, Vista, and Windows 7 (32 & 64-bit editions) Outlook 2003, 2007 and both 32 & 64-bit editions of Outlook 2010. Download Xobni Plus Download Xobni Free Edition Rating Installation: 8 Ease of Use: 8 Features: 9 Performance: 8 Product Support: 8 Similar Articles Productive Geek Tips Xobni Free Powers Up Outlook’s Search and ContactsCreate an Email Template in Outlook 2003Add Social Elements to Your Gmail Contacts with RapportiveChange Outlook Startup FolderClear Outlook Searches and MRU (Most Recently Used) Lists TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 10 Superb Firefox Wallpapers OpenDNS Guide Google TV The iPod Revolution Ultimate Boot CD can help when disaster strikes Windows Firewall with Advanced Security – How To Guides

  Read the article

• Yet again: "This device can perform faster" (Samsung Galaxy Tab 2)

  - by Mike C

  I've been doing a lot of research with no reasonable solution. Please excuse the length of my post. When I plug my Galaxy Tab 2 (7" / Wi-Fi only / Android ICS) into my Windows 7 64-bit machine, I (almost always) get this warning popup that "This device can perform faster." And in fact, transfers onto the Tab in this mode are slow. The two times I've been able to get a high-speed connection, the transfer has occurred at the expected speed. I just don't know what to do to get that high-speed transfer. (The first time I did, it was the first time I connected the Tab; the second time I did, I was fiddling around and unplugging/plugging in again.) That popup is telling me that the device is USB2, but that it thinks I've connected to a USB1 port. In fact, every USB port (there are ten) on this system is USB2. It's an ASUS M3A78-EMH mobo from late 2008. I'm not sure what the chipset is; the CPU is an AMD Athlon 4850e, but I've seen this message reported for non-AMD systems. (Every mobo reference I've seen in reports on this has been for Asus, but of course most reporters aren't reporting that info at all.) The Windows 7 installation is just a couple weeks old (I had a disk crash) but I saw the same warning on the WinXP/64 that was installed previously. In Device Manager, there are two "Standard Enhanced PCI to USB Host Controller" nodes which are the actual high-speed controllers. There are also five "Standard OpenHCD USB Host Controller" nodes, which I have determined are virtual USB1 controllers embedded in the "Enhanced" controllers. (In Device Manager, I'm using View|Devices by Connection.) My high-speed thumb drives, external disks, and iPod all show up as subnodes of the "Enhanced" controllers; the keyboard, mouse, and USB speakers under the "OpenHCD" ones -- and this is true no matter which ports these devices are plugged into. The Tab shows up under an OpenHCD node, unsurprisingly. It appears as a threesome: a top-level "Mobile USB Composite device" with two subs: "Galaxy Tab 2" and "Mobile USB Modem." (I have no idea what the modem device implies or how I might use it, but I don't care about it either: I just want the Tab to reliably connect at high speed.) On the Tab, the USB support has a switch between PTP and MTP, the latter being the default, and the preferred mode for me (as I'm usually hooking it up for music synch). I have tried, however, connecting it as PTP, and it still connects as USB 1. (As PTP, only the "Galaxy Tab 2" device appears -- no Composite, no Modem.) If it's plugged in as MTP and I change the setting to PTP, Windows unloads and reloads the device, and voila: The Tab appears under an "Enhanced" node, but eventually re-loads again to show a exclamation icon on the device; Properties then shows "This device cannot start." Same response if I plug it in as PTP and then change to MTP; in this case, only the Tab itself shows the exclamation, not the other two devices. One thing I have not tried, and really would prefer to avoid, is installing the "beta" chipset driver available on the Asus website, which is dated 2009. Windows tells me it has the most up-to-date drivers for the Tab, and for the chipset, and I'm inclined to believe that. I suspect the problem is with the Samsung drivers, or possibly the hardware. One suggestion I saw elsewhere which might, possibly, pertain is to ensure the USB cable is properly shielded; however, the Tab has one of those misbegotten 30-pin, not-quite-an-iPod connectors; I don't know if I could find a 3rd party one. It seems unlikely that this cable is improperly shielded, tho. (Is there a way to test that?) So, my question is: does anyone know how to get this working as one might reasonably expect it to?

  Read the article

• Application Does Not Start in Windows 7

  - by Jim Fell

  I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fresh from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried running sfc /scannow from the command line (with administrator privileges), shutting down the Spybot Resident, and disabling the firewall and virus scanner. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Faulting application name: SSDFresh.exe, version: 1.0.0.0, time stamp: 0x4f2a45d8 Faulting module name: unknown, version: 0.0.0.0, time stamp: 0x00000000 Exception code: 0xc0000005 Fault offset: 0x000007ff0016dbba Faulting process id: 0x994 Faulting application start time: 0x01cd11fd9fe978df Faulting application path: C:\Program Files (x86)\SSD Fresh\SSDFresh.exe Faulting module path: unknown Report Id: dfeed551-7df0-11e1-a2c7-002522c47ec0 Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Application: SSDFresh.exe Framework Version: v4.0.30319 Description: The process was terminated due to an unhandled exception. Exception Info: System.NullReferenceException Stack: at AbBugReporter.BugForm.InitLanguage() at AbBugReporter.BugForm..ctor(AbFlexTrans.LanguageInfo, AbBugReporter.BugReportManager, Boolean) at AbBugReporter.BugReportManager.Show(System.Exception) at SSDFresh.App.App_DispatcherUnhandledException(System.Object, System.Windows.Threading.DispatcherUnhandledExceptionEventArgs) at System.Windows.Threading.Dispatcher.CatchException(System.Exception) at MS.Internal.Threading.ExceptionFilterHelper.TryCatchWhen(System.Object, System.Delegate, System.Object, Int32, System.Delegate) at System.Windows.Threading.Dispatcher.WrappedInvoke(System.Delegate, System.Object, Int32, System.Delegate) at System.Windows.Threading.Dispatcher.InvokeImpl(System.Windows.Threading.DispatcherPriority, System.TimeSpan, System.Delegate, System.Object, Int32) at MS.Win32.HwndSubclass.SubclassWndProc(IntPtr, Int32, IntPtr, IntPtr) at MS.Win32.UnsafeNativeMethods.DispatchMessage(System.Windows.Interop.MSG ByRef) at System.Windows.Threading.Dispatcher.PushFrameImpl(System.Windows.Threading.DispatcherFrame) at System.Windows.Application.RunInternal(System.Windows.Window) at System.Windows.Application.Run() at SSDFresh.App.Main() Error 4/2/2012 11:35:39 PM SideBySide 59 None Activation context generation failed for "C:\Windows\Microsoft.NET\Framework64\v4.0.30319\csc.exe".Error in manifest or policy file "C:\Windows\Microsoft.NET\Framework64\v4.0.30319\csc.exe.Config" on line 0. Invalid Xml syntax. Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

  Read the article

• Choice of an OS for a home ZFS NAS

  - by OlafM

  I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post.

  Read the article

• Choice of an OS for a home ZFS NAS

  - by OlafM

  I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post. UPDATES Given the first answers, I will strongly suggest the person paying the hardware to insert a second HD. Better 2x2TB than 1x3TB (3 TB is oversized anyway). I was trying to keep the initial costs down to spread them over a longer period, but better having something good from the beginning.

  Read the article

• Installing Lubuntu 14.04.1 forcepae fails

  - by Rantanplan

  I tried to install Lubuntu 14.04.1 from a CD. First, I chose Try Lubuntu without installing which gave: ERROR: PAE is disabled on this Pentium M (PAE can potentially be enabled with kernel parameter "forcepae" ... Following the description on https://help.ubuntu.com/community/PAE, I used forcepae and tried Try Lubuntu without installing again. That worked fine. dmesg | grep -i pae showed: [ 0.000000] Kernel command line: file=/cdrom/preseed/lubuntu.seed boot=casper initrd=/casper/initrd.lz quiet splash -- forcepae [ 0.008118] PAE forced! On the live-CD session, I tried installing Lubuntu double clicking on the install button on the desktop. Here, the CD starts running but then stops running and nothing happens. Next, I rebooted and tried installing Lubuntu directly from the boot menu screen using forcepae again. After a while, I receive the following error message: The installer encountered an unrecoverable error. A desktop session will now be run so that you may investigate the problem or try installing again. Hitting Enter brings me to the desktop. For what errors should I search? And how? Finally, I rebooted once more and tried Check disc for defects with forcepae option; no errors have been found. Now, I am wondering how to find the error or whether it would be better to follow advice c in https://help.ubuntu.com/community/PAE: "Move the hard disk to a computer on which the processor has PAE capability and PAE flag (that is, almost everything else than a Banias). Install the system as usual but don't add restricted drivers. After the install move the disk back." Thanks for some hints! Perhaps some of the following can help: On Lubuntu 12.04: cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 13 model name : Intel(R) Pentium(R) M processor 1.50GHz stepping : 6 microcode : 0x17 cpu MHz : 600.000 cache size : 2048 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr mce cx8 mtrr pge mca cmov clflush dts acpi mmx fxsr sse sse2 ss tm pbe up bts est tm2 bogomips : 1284.76 clflush size : 64 cache_alignment : 64 address sizes : 32 bits physical, 32 bits virtual power management: uname -a Linux humboldt 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:45:51 UTC 2014 i686 i686 i386 GNU/Linux lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.5 LTS Release: 12.04 Codename: precise cpuid eax in eax ebx ecx edx 00000000 00000002 756e6547 6c65746e 49656e69 00000001 000006d6 00000816 00000180 afe9f9bf 00000002 02b3b001 000000f0 00000000 2c04307d 80000000 80000004 00000000 00000000 00000000 80000001 00000000 00000000 00000000 00000000 80000002 20202020 20202020 65746e49 2952286c 80000003 6e655020 6d756974 20295228 7270204d 80000004 7365636f 20726f73 30352e31 007a4847 Vendor ID: "GenuineIntel"; CPUID level 2 Intel-specific functions: Version 000006d6: Type 0 - Original OEM Family 6 - Pentium Pro Model 13 - Stepping 6 Reserved 0 Brand index: 22 [not in table] Extended brand string: " Intel(R) Pentium(R) M processor 1.50GHz" CLFLUSH instruction cache line size: 8 Feature flags afe9f9bf: FPU Floating Point Unit VME Virtual 8086 Mode Enhancements DE Debugging Extensions PSE Page Size Extensions TSC Time Stamp Counter MSR Model Specific Registers MCE Machine Check Exception CX8 COMPXCHG8B Instruction SEP Fast System Call MTRR Memory Type Range Registers PGE PTE Global Flag MCA Machine Check Architecture CMOV Conditional Move and Compare Instructions FGPAT Page Attribute Table CLFSH CFLUSH instruction DS Debug store ACPI Thermal Monitor and Clock Ctrl MMX MMX instruction set FXSR Fast FP/MMX Streaming SIMD Extensions save/restore SSE Streaming SIMD Extensions instruction set SSE2 SSE2 extensions SS Self Snoop TM Thermal monitor 31 reserved TLB and cache info: b0: unknown TLB/cache descriptor b3: unknown TLB/cache descriptor 02: Instruction TLB: 4MB pages, 4-way set assoc, 2 entries f0: unknown TLB/cache descriptor 7d: unknown TLB/cache descriptor 30: unknown TLB/cache descriptor 04: Data TLB: 4MB pages, 4-way set assoc, 8 entries 2c: unknown TLB/cache descriptor On Lubuntu 14.04.1 live-CD with forcepae: cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 13 model name : Intel(R) Pentium(R) M processor 1.50GHz stepping : 6 microcode : 0x17 cpu MHz : 600.000 cache size : 2048 KB physical id : 0 siblings : 1 core id : 0 cpu cores : 1 apicid : 0 initial apicid : 0 fdiv_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov clflush dts acpi mmx fxsr sse sse2 ss tm pbe bts est tm2 bogomips : 1284.68 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 32 bits virtual power management: uname -a Linux lubuntu 3.13.0-32-generic #57-Ubuntu SMP Tue Jul 15 03:51:12 UTC 2014 i686 i686 i686 GNU/Linux lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 14.04.1 LTS Release: 14.04 Codename: trusty cpuid CPU 0: vendor_id = "GenuineIntel" version information (1/eax): processor type = primary processor (0) family = Intel Pentium Pro/II/III/Celeron/Core/Core 2/Atom, AMD Athlon/Duron, Cyrix M2, VIA C3 (6) model = 0xd (13) stepping id = 0x6 (6) extended family = 0x0 (0) extended model = 0x0 (0) (simple synth) = Intel Pentium M (Dothan B1) / Celeron M (Dothan B1), 90nm miscellaneous (1/ebx): process local APIC physical ID = 0x0 (0) cpu count = 0x0 (0) CLFLUSH line size = 0x8 (8) brand index = 0x16 (22) brand id = 0x16 (22): Intel Pentium M, .13um feature information (1/edx): x87 FPU on chip = true virtual-8086 mode enhancement = true debugging extensions = true page size extensions = true time stamp counter = true RDMSR and WRMSR support = true physical address extensions = false machine check exception = true CMPXCHG8B inst. = true APIC on chip = false SYSENTER and SYSEXIT = true memory type range registers = true PTE global bit = true machine check architecture = true conditional move/compare instruction = true page attribute table = true page size extension = false processor serial number = false CLFLUSH instruction = true debug store = true thermal monitor and clock ctrl = true MMX Technology = true FXSAVE/FXRSTOR = true SSE extensions = true SSE2 extensions = true self snoop = true hyper-threading / multi-core supported = false therm. monitor = true IA64 = false pending break event = true feature information (1/ecx): PNI/SSE3: Prescott New Instructions = false PCLMULDQ instruction = false 64-bit debug store = false MONITOR/MWAIT = false CPL-qualified debug store = false VMX: virtual machine extensions = false SMX: safer mode extensions = false Enhanced Intel SpeedStep Technology = true thermal monitor 2 = true SSSE3 extensions = false context ID: adaptive or shared L1 data = false FMA instruction = false CMPXCHG16B instruction = false xTPR disable = false perfmon and debug = false process context identifiers = false direct cache access = false SSE4.1 extensions = false SSE4.2 extensions = false extended xAPIC support = false MOVBE instruction = false POPCNT instruction = false time stamp counter deadline = false AES instruction = false XSAVE/XSTOR states = false OS-enabled XSAVE/XSTOR = false AVX: advanced vector extensions = false F16C half-precision convert instruction = false RDRAND instruction = false hypervisor guest status = false cache and TLB information (2): 0xb0: instruction TLB: 4K, 4-way, 128 entries 0xb3: data TLB: 4K, 4-way, 128 entries 0x02: instruction TLB: 4M pages, 4-way, 2 entries 0xf0: 64 byte prefetching 0x7d: L2 cache: 2M, 8-way, sectored, 64 byte lines 0x30: L1 cache: 32K, 8-way, 64 byte lines 0x04: data TLB: 4M pages, 4-way, 8 entries 0x2c: L1 data cache: 32K, 8-way, 64 byte lines extended feature flags (0x80000001/edx): SYSCALL and SYSRET instructions = false execution disable = false 1-GB large page support = false RDTSCP = false 64-bit extensions technology available = false Intel feature flags (0x80000001/ecx): LAHF/SAHF supported in 64-bit mode = false LZCNT advanced bit manipulation = false 3DNow! PREFETCH/PREFETCHW instructions = false brand = " Intel(R) Pentium(R) M processor 1.50GHz" (multi-processing synth): none (multi-processing method): Intel leaf 1 (synth) = Intel Pentium M (Dothan B1), 90nm

  Read the article

• My D-Link's Ethernet bridge downlink just got 10-30x slower?

  - by Jay Levitt

  TL;DR: I unplugged my network to move my desk, and now downloading via my DIR-655's Ethernet LAN bridge is 10-30x slower than the Ethernet switch it's plugged into. Background My network is SMC cable modem <-> Cisco firewall <-> Netgear switch <-> D-Link WiFi† | | | | SMC8014 ASA-5505 GS608v2 gigE DIR-655 rev A3 gigE †The DIR-655 is used as an access point, not a router (although what D-Link calls an access point, I'd call a bridge). The "WAN" port is unused; the Netgear connects to the built-in 4-port Ethernet LAN switch, inside the built- in router/firewall. Endpoints: MacBook Pro 17" mid-2010 iPhone 4S Fedora 12 Linux server running reasonably fast dual-Athlon X2, VelociRaptors, etc. All cables are <10 feet, mostly CAT-5e, some CAT-6, all premade. All WiFi endpoints are within three feet of the D-Link. Yesterday I unplugged and rearranged stuff, and now connecting via the D-Link - even through the wired switch, right next to the incoming network cable - is 30x slower than connecting directly to the Netgear switch, on both my MacBook and iPhone. How I'm measuring "slower" I'm mostly using http://speedtest.net, which of course only really measures broadband speeds. I've also installed http://www.speedtest.net/mini.php on my local server, but can't test the iPhone with that. Results Speedtest.net, closest server over Comcast business-class: CONFIG | PING (ms) | DOWN (Mbps) | UP (Mbps) Mac <-> Ethernet <-> Netgear | 9 | 31.6 | 6.8 Mac <-> Ethernet <-> D-Link | 8 | 4.1 | 6.0 Mac <-> WiFi <-> D-Link | 9 | 1.4 | 2.9 iPhone <-> WiFi <-> D-Link | 67 | 0.4 | 1.6 Speedtest Mini on Linux PC: CONFIG | DOWN (Mbps) | UP (Mbps) Mac <-> Ethernet <-> NetGear | 97.2 | 76.9 Mac <-> Ethernet <-> D-Link | 8.2 | 24.2 Mac <-> WiFi <-> D-Link | 1.0 | 8.6 Slow typing in SSH: Mac <-> Ethernet <-> Netgear <-> Linux PC: smooth Mac <-> Ethernet <-> D-Link <-> Linux PC: choppy Note that D-Link upload speeds are normal on broadband, slower locally (but I'd believe that's a D-Link limitation), and always faster than the downloads! Since ssh is choppy just with slow typing, I don't believe it's a throttling-type problem either; that's not a lot of bandwidth. What I've tried Swapping all "good" and "bad" cables Re-plugging "bad" cable from D-Link to Netgear and watching it be the "good" cable pulling cables away from power lines Verify that the Mac auto-detects the D-Link as gigE Try to verify the link speed of the D-Link <- Netgear connection, but the firmware doesn't report that Verify that the D-Link sees no TX/RX errors or collisions Use different Ethernet ports on both Netgear and D-Link Reset the D-Link to factory settings Upgrade the D-Link firmware from 1.21 to 1.35NA, 2010/11/12, the latest Reboot everything at least once On the Mac, disable Wi-Fi during the Ethernet tests, and unplug Ethernet during the Wi-Fi tests Using iStumbler, verify that the D-Link isn't picking overloaded Wi-Fi channels (usually just 1-5 neighbors on my and adjacent channels, average for my apt building) Verify that the only client connected to the Wi-Fi was the iPhone Verify that nothing was being chatty on my network according to the WISH log Enable and disable all sorts of D-Link settings, including forcing WAN auto-detect to gigE So. I don't mind buying a new access point—I wouldn't mind having a dual-link network—but as a guy who's been networking since gated v4 was a drastic rewrite, and who often used physical sniffers in the days before Wireshark, I'm baffled. I hate being baffled. What could I possibly have changed that would result in this? How can I measure it? All I can think of is a static zap—thick carpet, socks, HVAC—but I didn't feel one, and does that really happen anymore? Can I test if it's Ethernet vs. TCP layer slowness? I'm not familiar with modern network utilities; it's hard to Google without hitting "Q: Why is my network slow? A: Is your microwave on?" If I don't get an answer here, will someone big and powerful help me migrate it to serverfault without getting screamed back here? In the words of Inigo Montoya, "I must know." Don't get all Dread Pirate Roberts on me.

  Read the article

• Build and migrated to software raid (mdadm) on GPT disk, now can't assemble array

  - by John H

  mdadm, gpt issues, unrecognized partitions. Simplified question: How do I get mdadm to recognize GPT partitions? I have been attempting to convert/copy my Ubuntu 11.10 OS from a single drive to software raid 1. I have done similar in the past, but in this case, I was adding in a drive that has been configured for GPT and I tried to work with that without fully looking into the implications. Currently, I have a non-booting mdadm RAID 1 array of /dev/md127 (the OS assigned that and it keeps picking up). I am booting off of live USB keys, currently System Rescue CD from sysresccd. While gdisk and parted can see all the partitions, most of the OS utilities do not, including mdadm. My main goal is just to make the raid array accessible so I can get pull the data and start fresh (without using GPT). /dev/md127 /dev/sda /dev/sda1 <- GPT type partition /dev/sda1 <- exists within the GPT part, member of md127 /dev/sda2 <- exists within the GPT part, empty /dev/sdb /dev/sdb1 <- GPT type partition /dev/sdb1 <- exists within the GPT part, member of md127 History: POINT A: The original OS was install on sda (actually /dev/sda6). I used a the Ubuntu live usb to add sdb. I got warning from fdisk about GPT so I used gdisk to create a raid partition (sdb1) and mdadm to create a raid1 mirror with a missing drive. I had many issues getting this working (including being unable to get grub to install) but I eventually got it to boot using grub on sda and /dev/md127 off of sdb. So at point A, I had copied my OS from sda6 to md127 on sdb. I then booted into a rescue mode and attempted to get a bootloader onto sdb, which failed. I then discovered my mistake: I had installed the raid onto sdb instead of sdb1, essentially overwriting the sdb1 partition. POINT B: I now had two copies of my data- one on md127/sdb, and one on sda. I destroyed data on sda and created a new GPT table on sda. I then created sda1 for the raid array, and sda2 for a scratch partition. I added sda1 into the raid array and let it rebuild. md127 now covered /dev/sdb and /dev/sda1 as fully active and synced. POINT C: I rebooted onto linux rescue again and was still able to access the raid array. I then removed /dev/sdb from the array and created /dev/sdb1 for the raid. I added sdb1 to the array and let it sync. I was able to mount and access /dev/md127 without issues. Once it completed, both /dev/sda1 and /dev/sdb1 were GPT partitions and actively syncing. POINT D (current): I rebooted again to test if the array would boot and grub failed to load. I booted off of my live thumb drive and found that I can no longer assemble the raid array. mdadm doesn't see the required partitions. -- root@freshdesk /root % uname -a Linux freshdesk 3.0.24-std251-amd64 #2 SMP Sat Mar 17 12:08:55 UTC 2012 x86_64 AMD Athlon(tm) II X4 645 Processor AuthenticAMD GNU/Linux === /proc/partitions and parted look good: root@freshdesk /root % cat /proc/partitions major minor #blocks name 7 0 301788 loop0 8 0 976762584 sda 8 1 732579840 sda1 8 2 244181703 sda2 8 16 732574584 sdb 8 17 732573543 sdb1 8 32 7876607 sdc 8 33 7873349 sdc1 (parted) print all Model: ATA ST31000528AS (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 750GB 750GB ext4 2 750GB 1000GB 250GB Linux/Windows data Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 750GB 750GB ext4 Linux RAID raid Model: SanDisk SanDisk Cruzer (scsi) Disk /dev/sdc: 8066MB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 31.7kB 8062MB 8062MB primary fat32 boot, lba === # no sda2, and I double the sdb1 is the one shown in parted root@freshdesk /root % blkid /dev/loop0: TYPE="squashfs" /dev/sda1: UUID="75dd6c2d-f0a8-4302-9da4-792cc7d72355" TYPE="ext4" /dev/sdc1: LABEL="PENDRIVE" UUID="1102-3720" TYPE="vfat" /dev/sdb1: UUID="2dd89f15-65bb-ff88-e368-bf24bd0fce41" TYPE="linux_raid_member" root@freshdesk /root % mdadm -E /dev/sda1 mdadm: No md superblock detected on /dev/sda1. # this is probably a result of me attempting to force the array up, putting superblocks on the GPT partition root@freshdesk /root % mdadm -E /dev/sdb1 /dev/sdb1: Magic : a92b4efc Version : 0.90.00 UUID : 2dd89f15:65bbff88:e368bf24:bd0fce41 Creation Time : Fri Mar 30 19:25:30 2012 Raid Level : raid1 Used Dev Size : 732568320 (698.63 GiB 750.15 GB) Array Size : 732568320 (698.63 GiB 750.15 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 127 Update Time : Sat Mar 31 12:39:38 2012 State : clean Active Devices : 1 Working Devices : 2 Failed Devices : 1 Spare Devices : 1 Checksum : a7d038b3 - correct Events : 20195 Number Major Minor RaidDevice State this 2 8 17 2 spare /dev/sdb1 0 0 8 1 0 active sync /dev/sda1 1 1 0 0 1 faulty removed 2 2 8 17 2 spare /dev/sdb1 === root@freshdesk /root % mdadm -A /dev/md127 /dev/sda1 /dev/sdb1 mdadm: no recogniseable superblock on /dev/sda1 mdadm: /dev/sda1 has no superblock - assembly aborted root@freshdesk /root % mdadm -A /dev/md127 /dev/sdb1 mdadm: cannot open device /dev/sdb1: Device or resource busy mdadm: /dev/sdb1 has no superblock - assembly aborted

  Read the article

• Stream Media and Live TV Across the Internet with Orb

  - by DigitalGeekery

  Looking for a way to stream your media collection across the Internet? Or perhaps watch and record TV remotely? Today we are going to look at how to do all that and more with Orb. Requirements Windows XP / Vista / 7 or Intel based Mac w/ OS X 10.5 or later. 1 GB RAM or more Pentium 4 2.4 GHz or higher / AMD Athlon 3200+ Broadband connections TV Tuner for streaming and recording live TV (optional) Note: Slower internet connections may result in stuttering during playback. Installation and Setup Download and install Orb on your home computer. (Download link below) You’ll want to take the defaults for the initial portion of the install. When we get to the Orb Account setup portion of the install is when we will have to enter information and make some decisions. Choose your language and click Next. We’ll need to create and user account and password. A valid email address is required as we’ll need to confirm the account later. Click Next.   Now you’ll want to choose your media sources. Orb will automatically look for folders that may contain media files. You can add or remove folders click on the (+) or (-) buttons. To remove a folder, click on it once to select it from the list and then click the minus (-) button. To add a folder, click the plus (+) button and browse for the folder. You can add local folders as well as shared folders from networked computers and USB attached storage. Note: Both the host computer running Orb and the networked computer will need to be running to access shared network folders remotely. When you’ve selected all your media files, click Next. Orb will proceed to index your media files… When the indexing is complete, click Next. Orb TV Setup Note: Streaming Live TV to Macs is not currently supported. If you have a TV tuner card connected to your PC, you can opt to configure Orb to stream live or recorded TV. Click Next  to configure TV. Or, choose Skip if you don’t wish to configure Orb for TV.   If you have a Digital tuner card, type in your Zip Code and click Get List to pull your channel listings. Select a TV provider from the list and click Next. If not, click Skip.   You can select or deselect any channels by checking or un-checking the box to each channel. Select Auto Scan to let Orb find more channels or disable the ones with no reception. Click Next when finished.   Next choose an analog provider, if necessary, and click Next.   Select “Yes” or “No” for a set top box and click Next. Just as we did with the Digital tuner, select or deselect any channels by checking or un-checking the box to each channel. Select Auto Scan to let Orb find more channels or disable the ones with no reception. Click Next when finished.   Now we’re finished with the setup. Click Close. Accessing your Media Remotely Media files are accessed through a web-based interface. Before we go any further, however, we’ll need to confirm our username and password. Check your inbox for an email from Orb Networks. Click the enclosed confirmation link. You’ll be prompted to enter the username and password you selected in your browser then click Next.   Your account will be confirmed. Now, we’re ready to enjoy our media remotely. To get started, point your browser to the MyCast website from your remote computer. (See link below) Enter your credentials and click Log In. Once logged in, you’ll be presented with the MyCast Home screen. By default you’ll see a handful of “channels” such as a TV program guide, random audio and photos, video favorites, and weather. You can add, remove, or customize channels. To add additional channels, click on Add Channels at the top right…   …and select from the dropdown list. To access your full media libraries, click Open Application at the top left and select from one of the options. Live and Recorded TV If you have a TV tuner card you configured for Orb, you’ll see your program guide on the TV / Webcams screen. To watch or record a show, click on the program listing to bring up a detail box. Then click the red button to record, or the green button to play. When recording a show, you’ll see a pulsating red icon at the top right of the listing in the program guide. If you want to watch Live TV, you may be prompted to choose your media player, depending on your browser and settings. Playback should begin shortly.   Note for Windows Media Center Users If you try to stream live TV in Orb while Windows Media Center is running on your PC, you’ll get an error message. Click the Stop MediaCenter button and then try again.   Audio On the Audio screen, you’ll find your music files indexed by genre, artist, and album. You can play a selection by clicking once and then clicking the green play button, or by simply double-clicking.   Playback will begin in the default media player for the streaming format.   Video Video works essentially the same as audio. Click on a selection and press the green play button, or double-click on the video title. Video playback will begin in the default media player for the streaming format.   Streaming Formats You can change the default streaming format in the control panel settings. To access the Control Panel, click on Open Applications  and select Control Panel. You can also click Settings at the top right.   Select General from the drop down list and then click on the Streaming Formats tab. You are provided four options. Flash, Windows Media, .SDP, and .PLS.   Creating Playlists To create playlists, drag and drop your media title to the playlist work area on the right, or click Add to playlist on the top menu. Click Save when finished.    Sharing your Media Orb allows you to share media playlists across the Internet with friends and family. There are a few ways to accomplish this. We’ll start by click the Share button at the bottom of the playlist work area after you’ve compiled your playlist. You’ll be prompted to choose a method by which to share your playlist. You’ll have the option to share your playlist publicly or privately. You can share publically through links, blogs, or on your Orb public profile.  By choosing the Public Profile option, Orb will automatically create a profile page for you with a URL like http://public.orb.com/username that anyone can easily access on the Internet. The private sharing option allows you to invite friends by email and requires recipients to register with Orb. You can also give your playlist a custom name, or accept the auto-generated title. Click OK when finished. Users who visit your public profile will be able to view and stream any of your shared playlists to their computer or supported device.   Portable Media Devices and Smartphones Orb can stream media to many portable devices and 3G phones. Streaming audio is supported on the iPhone and iPod Touch through the Safari browser. However, video and live TV streaming requires the Orb Live iPhone App.  Orb Live is available in the App store for $9.99. To stream media to your portable device, go to the MyCast website in your mobile browser and login. Browse for your media or playlist. Make a selection and play the media. Playback will begin. We found streaming music to both the Droid and the iPhone to work quite nicely. Video playback on the Droid, however, left a bit to be desired. The video looked good, but the audio tended to be out of sync. System Tray Control Panel By default Orb runs in the system tray on start up. To access the System Tray Control Panel, right-click on the Orb icon in the system tray and select Control Panel. Login with your Orb username and  password and click OK.   From here you can add or remove media sources, add manage accounts, change your password, and more. If you’d rather not run Orb on Startup, click the General icon.   Unselect the checkbox next to Start Orb when the system starts. Conclusion It may seem like a lot of steps, but getting Orb up and running isn’t terribly difficult. Orb is available for both Windows and Intel based Macs. It also supports streaming to many Game Consoles such as the Wii, PS3, and XBox 360. If you are running Windows 7 on multiple computers, you may want to check out our write-up on how to stream music and video over the Internet with Windows Media Player 12. Downloads Download Orb Logon to MyCast Similar Articles Productive Geek Tips Stream Music and Video Over the Internet with Windows Media Player 12Enable Media Streaming in Windows Home Server to Windows Media PlayerStream Media from Windows 7 to XP with VLC Media PlayerShare Digital Media With Other Computers on a Home Network with Windows 7Automatically Start Windows 7 Media Center in Live TV Mode TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Looking for Good Windows Media Player 12 Plug-ins? Find Out the Celebrity You Resemble With FaceDouble Whoa ! Use Printflush to Solve Printing Problems Icelandic Volcano Webcams Open Multiple Links At One Go

  Read the article

• issue with std::advance on std::sets

  - by tim

  I've stumbled upon what I believe is a bug in the stl algorithm advance. When I'm advancing the iterator off of the end of the container, I get inconsistent results. Sometimes I get container.end(), sometimes I get the last element. I've illustrated this with the following code: #include <algorithm> #include <cstdio> #include <set> using namespace std; typedef set<int> tMap; int main(int argc, char** argv) { tMap::iterator i; tMap the_map; for (int i=0; i<10; i++) the_map.insert(i); #if EXPERIMENT==1 i = the_map.begin(); #elif EXPERIMENT==2 i = the_map.find(4); #elif EXPERIMENT==3 i = the_map.find(5); #elif EXPERIMENT==4 i = the_map.find(6); #elif EXPERIMENT==5 i = the_map.find(9); #elif EXPERIMENT==6 i = the_map.find(2000); #else i = the_map.end(); #endif advance(i, 100); if (i == the_map.end()) printf("the end\n"); else printf("wuh? %d\n", *i); return 0; } Which I get the following unexpected (according to me) behavior in experiment 3 and 5 where I get the last element instead of the_map.end(). [tim@saturn advance]$ uname -srvmpio Linux 2.6.18-1.2798.fc6 #1 SMP Mon Oct 16 14:37:32 EDT 2006 i686 athlon i386 GNU/Linux [tim@saturn advance]$ g++ --version g++ (GCC) 4.1.1 20061011 (Red Hat 4.1.1-30) Copyright (C) 2006 Free Software Foundation, Inc. This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. [tim@saturn advance]$ g++ -DEXPERIMENT=1 advance.cc [tim@saturn advance]$ ./a.out the end [tim@saturn advance]$ g++ -DEXPERIMENT=2 advance.cc [tim@saturn advance]$ ./a.out the end [tim@saturn advance]$ g++ -DEXPERIMENT=3 advance.cc [tim@saturn advance]$ ./a.out wuh? 9 [tim@saturn advance]$ g++ -DEXPERIMENT=4 advance.cc [tim@saturn advance]$ ./a.out the end [tim@saturn advance]$ g++ -DEXPERIMENT=5 advance.cc [tim@saturn advance]$ ./a.out wuh? 9 [tim@saturn advance]$ g++ -DEXPERIMENT=6 advance.cc [tim@saturn advance]$ ./a.out the end [tim@saturn advance]$ g++ -DEXPERIMENT=7 advance.cc [tim@saturn advance]$ ./a.out the end [tim@saturn advance]$ From the sgi website (see link at top), it has the following example: list<int> L; L.push_back(0); L.push_back(1); list<int>::iterator i = L.begin(); advance(i, 2); assert(i == L.end()); I would think that the assertion should apply to other container types, no? What am I missing? Thanks!

  Read the article

• BIND returns serverfail when querying for its authoriative domain

  - by estol

  Hi there Serverfault folks! First of all: sorry about the title, I had some problem coming up with the proper title. I have a little home server set up, for internet sharing, samba, basic http, dlna mediaserver and what not, and I happend to have a domain at hand, so I thought why not direct it to this computer? I have a BIND 9.8.0 installed, and - afaik - configured it properly. For a few days, the public view did not worked, and I really did not cared, since the local view worked. But now suddenly, even the local view fails. If I try to query the nameserver for anything in my domain, it returns the following error: $ nslookup andromeda.dafaces.com ;; Got SERVFAIL reply from ::1, trying next server ;; Got SERVFAIL reply from ::1, trying next server Server: 127.0.0.1 Address: 127.0.0.1#53 ** server can't find andromeda.dafaces.com.dafaces.com: SERVFAIL Also, the public view points to the old ip address of the domain, probably because of the same error. Some information about the system: $ uname -a Linux tressis 2.6.37-ARCH #1 SMP PREEMPT Tue Mar 15 09:21:17 CET 2011 x86_64 AMD Athlon(tm) 64 X2 Dual Core Processor 5000+ AuthenticAMD GNU/Linux $ named -v BIND 9.8.0 And the named.conf file: # cat /etc/named.conf // // /etc/named.conf // include "/etc/rndc.key"; #controls { # inet 127.0.0.1 allow {localhost; } keys { "dnskulcs"; }; #}; options { directory "/var/named"; pid-file "/var/run/named/named.pid"; auth-nxdomain yes; datasize default; // Uncomment these to enable IPv6 connections support // IPv4 will still work: listen-on-v6 { any; }; listen-on { any; }; // Add this for no IPv4: // listen-on { none; }; // Default security settings. // allow-recursion { 127.0.0.1; ::1; 192.168.1.0/24; }; // allow-recursion { any; }; allow-query { any; }; allow-transfer { 127.0.0.1; ::1; 92.243.14.172; 87.98.164.164; 88.191.64.64; }; allow-update { key "dnskulcs"; }; version none; hostname none; server-id none; zone-statistics yes; forwarders { 213.46.246.53; 213.26.246.54; 8.8.8.8; 8.8.4.4; 192.188.242.65; 193.227.196.3; 2001:470:20::2; }; }; view "local" { match-clients { 192.168.1.0/24; 127.0.0.1; ::1; fec0:0:0:ffff::/64; }; recursion yes; zone "localhost" IN { type master; file "localhost.zone"; allow-transfer { any; }; }; zone "0.0.127.in-addr.arpa" IN { type master; file "127.0.0.zone"; allow-transfer { any; }; }; zone "." IN { type hint; file "root.hint"; }; zone "dafaces.com" IN { type master; file "internal/dafaces.com.fw"; allow-update { key "dnskulcs"; }; }; zone "1.168.192.in-addr.arpa" IN { type master; file "internal/dafaces.com.rev"; allow-update { key "dnskulcs"; }; }; }; view "public" { match-clients { any;}; recursion no; zone "dafaces.com" IN { type master; file "external/dafaces.com.fw"; allow-transfer { 87.98.164.164; 195.234.42.1; 88.191.64.64; }; }; }; //zone "example.org" IN { // type slave; // file "example.zone"; // masters { // 192.168.1.100; // }; // allow-query { any; }; // allow-transfer { any; }; //}; logging { channel xfer-log { file "/var/log/named.log"; print-category yes; print-severity yes; print-time yes; severity info; }; category xfer-in { xfer-log; }; category xfer-out { xfer-log; }; category notify { xfer-log; }; }; All help would be highly appreciated! EDIT: Zone files: # cat /var/named/internal/dafaces.com.fw $ORIGIN . $TTL 3600 ; 1 hour dafaces.com IN SOA tressis.dafaces.com. postmaster.dafaces.com. ( 2011032201 ; serial 28800 ; refresh (8 hours) 7200 ; retry (2 hours) 2419200 ; expire (4 weeks) 3600 ; minimum (1 hour) ) NS tressis.dafaces.com. A 192.168.1.1 MX 10 mail.dafaces.com. $ORIGIN _tcp.dafaces.com. _http SRV 0 5 80 www.dafaces.com. _ssh SRV 0 5 22 tressis.dafaces.com. $ORIGIN dafaces.com. acrisius A 192.168.1.230 andromeda A 192.168.1.7 andromeda-win7 CNAME andromeda aspasia A 192.168.1.233 athena A 192.168.1.232 callisto A 192.168.1.102 db A 192.168.1.1 management A 192.168.1.1 ; web management for the router functions haley A 192.168.1.5 hoth A 192.168.1.101 mail A 192.168.1.1 satelite A 192.168.1.20 sony-player A 192.168.1.103 TXT "310f16de2d2712dfc4ae6e5c54f60f828e" torrent A 192.168.1.1 tracker A 192.168.1.1 tressis A 192.168.1.1 www A 192.168.1.1 zeus A 192.168.1.231 and # cat /var/named/external/dafaces.com.fw $ORIGIN . $TTL 3600 dafaces.com IN SOA ns.dafaces.com. postmaster.dafaces.com. ( 2011032405; serial 28800; refresh 7200; retry 2419200; expire 3600; minimum ) NS ns.dafaces.com. NS ns0.xname.org. NS ns1.xname.org. NS ns2.xname.org. A 89.135.129.37 MX 10 mail.dafaces.com. $ORIGIN dafaces.com. ;Szolgaltatasok _ssh._tcp SRV 0 5 22 tressis _http._tcp SRV 0 5 80 www ns A 89.135.129.37 hoth A 89.135.129.37 www A 89.135.129.37 mail A 89.135.129.37 db A 89.135.129.37 torrent A 89.135.129.37 tracker A 89.135.129.37 Edit: Ohh, hell I almost forgot. Since the node is connected to the internet via a residential connection, there is a possibility, that the public ipv4 address will change(but thank god, it is a very rare case), so I daily update the external IP address in the zone file with a shellscript: # cat /etc/cron.daily/dnsupdate #!/bin/sh FILE="/var/named/external/dafaces.com.fw" SERIAL=$(date +%Y%m%d05) PUBLIC_IP=$(ifconfig internet |sed -n "/inet addr:.*255.255.255.255/{s/.*inet addr://; s/ .*//; p}") cat $FILE | sed --posix 's/^.* serial$/\t\t\t\t\t'$SERIAL'; serial/' | sed --posix 's/[0-9]*\.[0-9]*\.[0-9]*\.[0-9]*/'$PUBLIC_IP'/' > /tmp/ujzona mv /tmp/ujzona $FILE /etc/rc.d/named reload

  Read the article

• rotating bitmaps. In code.

  - by Marco van de Voort

  Is there a faster way to rotate a large bitmap by 90 or 270 degrees than simply doing a nested loop with inverted coordinates? The bitmaps are 8bpp and typically 2048*2400*8bpp Currently I do this by simply copying with argument inversion, roughly (pseudo code: for x = 0 to 2048-1 for y = 0 to 2048-1 dest[x][y]=src[y][x]; (In reality I do it with pointers, for a bit more speed, but that is roughly the same magnitude) GDI is quite slow with large images, and GPU load/store times for textures (GF7 cards) are in the same magnitude as the current CPU time. Any tips, pointers? An in-place algorithm would even be better, but speed is more important than being in-place. Target is Delphi, but it is more an algorithmic question. SSE(2) vectorization no problem, it is a big enough problem for me to code it in assembler Duplicates How do you rotate a two dimensional array?. Follow up to Nils' answer Image 2048x2700 - 2700x2048 Compiler Turbo Explorer 2006 with optimization on. Windows: Power scheme set to "Always on". (important!!!!) Machine: Core2 6600 (2.4 GHz) time with old routine: 32ms (step 1) time with stepsize 8 : 12ms time with stepsize 16 : 10ms time with stepsize 32+ : 9ms Meanwhile I also tested on a Athlon 64 X2 (5200+ iirc), and the speed up there was slightly more than a factor four (80 to 19 ms). The speed up is well worth it, thanks. Maybe that during the summer months I'll torture myself with a SSE(2) version. However I already thought about how to tackle that, and I think I'll run out of SSE2 registers for an straight implementation: for n:=0 to 7 do begin load r0, <source+n*rowsize> shift byte from r0 into r1 shift byte from r0 into r2 .. shift byte from r0 into r8 end; store r1, <target> store r2, <target+1*<rowsize> .. store r8, <target+7*<rowsize> So 8x8 needs 9 registers, but 32-bits SSE only has 8. Anyway that is something for the summer months :-) Note that the pointer thing is something that I do out of instinct, but it could be there is actually something to it, if your dimensions are not hardcoded, the compiler can't turn the mul into a shift. While muls an sich are cheap nowadays, they also generate more register pressure afaik. The code (validated by subtracting result from the "naieve" rotate1 implementation): const stepsize = 32; procedure rotatealign(Source: tbw8image; Target:tbw8image); var stepsx,stepsy,restx,resty : Integer; RowPitchSource, RowPitchTarget : Integer; pSource, pTarget,ps1,ps2 : pchar; x,y,i,j: integer; rpstep : integer; begin RowPitchSource := source.RowPitch; // bytes to jump to next line. Can be negative (includes alignment) RowPitchTarget := target.RowPitch; rpstep:=RowPitchTarget*stepsize; stepsx:=source.ImageWidth div stepsize; stepsy:=source.ImageHeight div stepsize; // check if mod 16=0 here for both dimensions, if so -> SSE2. for y := 0 to stepsy - 1 do begin psource:=source.GetImagePointer(0,y*stepsize); // gets pointer to pixel x,y ptarget:=Target.GetImagePointer(target.imagewidth-(y+1)*stepsize,0); for x := 0 to stepsx - 1 do begin for i := 0 to stepsize - 1 do begin ps1:=@psource[rowpitchsource*i]; // ( 0,i) ps2:=@ptarget[stepsize-1-i]; // (maxx-i,0); for j := 0 to stepsize - 1 do begin ps2[0]:=ps1[j]; inc(ps2,RowPitchTarget); end; end; inc(psource,stepsize); inc(ptarget,rpstep); end; end; // 3 more areas to do, with dimensions // - stepsy*stepsize * restx // right most column of restx width // - stepsx*stepsize * resty // bottom row with resty height // - restx*resty // bottom-right rectangle. restx:=source.ImageWidth mod stepsize; // typically zero because width is // typically 1024 or 2048 resty:=source.Imageheight mod stepsize; if restx>0 then begin // one loop less, since we know this fits in one line of "blocks" psource:=source.GetImagePointer(source.ImageWidth-restx,0); // gets pointer to pixel x,y ptarget:=Target.GetImagePointer(Target.imagewidth-stepsize,Target.imageheight-restx); for y := 0 to stepsy - 1 do begin for i := 0 to stepsize - 1 do begin ps1:=@psource[rowpitchsource*i]; // ( 0,i) ps2:=@ptarget[stepsize-1-i]; // (maxx-i,0); for j := 0 to restx - 1 do begin ps2[0]:=ps1[j]; inc(ps2,RowPitchTarget); end; end; inc(psource,stepsize*RowPitchSource); dec(ptarget,stepsize); end; end; if resty>0 then begin // one loop less, since we know this fits in one line of "blocks" psource:=source.GetImagePointer(0,source.ImageHeight-resty); // gets pointer to pixel x,y ptarget:=Target.GetImagePointer(0,0); for x := 0 to stepsx - 1 do begin for i := 0 to resty- 1 do begin ps1:=@psource[rowpitchsource*i]; // ( 0,i) ps2:=@ptarget[resty-1-i]; // (maxx-i,0); for j := 0 to stepsize - 1 do begin ps2[0]:=ps1[j]; inc(ps2,RowPitchTarget); end; end; inc(psource,stepsize); inc(ptarget,rpstep); end; end; if (resty>0) and (restx>0) then begin // another loop less, since only one block psource:=source.GetImagePointer(source.ImageWidth-restx,source.ImageHeight-resty); // gets pointer to pixel x,y ptarget:=Target.GetImagePointer(0,target.ImageHeight-restx); for i := 0 to resty- 1 do begin ps1:=@psource[rowpitchsource*i]; // ( 0,i) ps2:=@ptarget[resty-1-i]; // (maxx-i,0); for j := 0 to restx - 1 do begin ps2[0]:=ps1[j]; inc(ps2,RowPitchTarget); end; end; end; end;

  Read the article

• WMI/VBS/HTML System Information Script

  - by Methical

  Hey guys; havin' a problem with this code here; can't seem to work out whats goin' wrong with it. All other variables seem to print fine in the HTML ouput; but I get an error that relates to the cputype variable. I get the following error C:\Users\Methical\Desktop\sysinfo.vbs(235,1) Microsoft VBScript runtime error: Invalid procedure call or argument I think it has somethin' to do with this line here fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>CPU</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & cputype & "</i></td></tr>" If i delete this line; the script compiles and outputs with no errors. Here is the full code below Dim strComputer, objWMIService, propValue, objItem Dim strUserName, strPassword, colItems, SWBemlocator ' This section querries for the workstation to be scanned. UserName = "" Password = "" strComputer = "127.1.1.1" ImgDir = "C:\Scripts\images\" 'Sets up the connections and opjects to be used throughout the script. Set SWBemlocator = CreateObject("WbemScripting.SWbemLocator") Set objWMIService = SWBemlocator.ConnectServer(,"root\CIMV2",strUserName,strPassword) 'This determines the current date and time of the PC being scanned. Set colItems = objWMIService.ExecQuery("SELECT * FROM Win32_LocalTime", "WQL", wbemFlagReturnImmediately + wbemFlagForwardOnly) For Each objItem in colItems If objItem.Minute < 10 Then theMinutes = "0" & objItem.Minute Else theMinutes = objItem.Minute End If If objItem.Second < 10 Then theSeconds = "0" & objItem.Second Else theSeconds = objItem.Second End If DateTime = objItem.Month & "/" & objItem.Day & "/" & objItem.Year & " - " & objItem.Hour & ":" & theMinutes & ":" & theSeconds Next 'Gets some ingomation about the Operating System including Service Pack level. Set colItems = objWMIService.ExecQuery("Select * from Win32_OperatingSystem",,48) For Each objItem in colItems WKID = objItem.CSName WKOS = objItem.Caption CSD = objItem.CSDVersion Architecture = objItem.OSArchitecture SysDir = objItem.SystemDirectory SysDrive = objItem.SystemDrive WinDir = objItem.WindowsDirectory ServicePack = objItem.ServicePackMajorVersion & "." & objItem.ServicePackMinorVersion Next 'This section returns the Time Zone Set colItems = objWMIService.ExecQuery("Select * from Win32_TimeZone") For Each objItem in colItems Zone = objItem.Description Next 'This section displays the Shadow Storage information Set colItems = objWMIService.ExecQuery("Select * from Win32_ShadowStorage") For Each objItem in colItems Allocated = int((objItem.AllocatedSpace/1024)/1024+1) UsedSpace = int((objItem.UsedSpace/1024)/1024+1) MaxSpace = int((objItem.MaxSpace/1024)/1024+1) Next 'This section returns the InstallDate of the OS Set objSWbemDateTime = _ CreateObject("WbemScripting.SWbemDateTime") Set colOperatingSystems = _ objWMIService.ExecQuery _ ("Select * from Win32_OperatingSystem") For Each objOperatingSystem _ in colOperatingSystems objSWbemDateTime.Value = _ objOperatingSystem.InstallDate InstallDate = _ objSWbemDateTime.GetVarDate(False) Next 'This section returns the Video card and current resolution. Set colItems = objWMIService.ExecQuery("Select * from Win32_DisplayConfiguration",,48) For Each objItem in colItems VideoCard = objItem.DeviceName Resolution = objItem.PelsWidth & " x " & objItem.PelsHeight & " x " & objItem.BitsPerPel & " bits" Next 'This section returns the Video card memory. Set objWMIService = GetObject("winmgmts:root\cimv2") Set colItems = objWMIService.ExecQuery ("Select * from Win32_VideoController") For Each objItem in colItems VideoMemory = objItem.AdapterRAM/1024/1024 Next 'This returns various system information including current logged on user, domain, memory, manufacture and model. Set colItems = objWMIService.ExecQuery("Select * from Win32_ComputerSystem",,48) For Each objItem in colItems UserName = objItem.UserName Domain = objItem.Domain TotalMemory = int((objItem.TotalPhysicalMemory/1024)/1024+1) Manufacturer = objItem.Manufacturer Model = objItem.Model SysType = objItem.SystemType Next 'This determines the total hard drive space and free hard drive space. Set colItems = objWMIService.ExecQuery("Select * from Win32_LogicalDisk Where Name='C:'",,48) For Each objItem in colItems FreeHDSpace = Fix(((objItem.FreeSpace/1024)/1024)/1024) TotalHDSpace = Fix(((objItem.Size/1024)/1024)/1024) Next 'This section returns the default printer and printer port. Set colItems = objWMIService.ExecQuery("SELECT * FROM Win32_Printer where Default=True", "WQL", wbemFlagReturnImmediately + wbemFlagForwardOnly) For Each objItem in colItems Printer = objItem.Name PortName = objItem.PortName Next 'This returns the CPU information. Set colItems = objWMIService.ExecQuery("SELECT * FROM Win32_Processor", "WQL", wbemFlagReturnImmediately + wbemFlagForwardOnly) For Each objItem in colItems CPUDesc = LTrim(objItem.Name) Next '// CPU Info For each objCPU in GetObject("winmgmts:{impersonationLevel=impersonate}\\" & strComputer & "\root\cimv2").InstancesOf("Win32_Processor") Select Case objCPU.Family Case 2 cputype = "Unknown" Case 11 cputype = "Pentium brand" Case 12 cputype = "Pentium Pro" Case 13 cputype = "Pentium II" Case 14 cputype = "Pentium processor with MMX technology" Case 15 cputype = "Celeron " Case 16 cputype = "Pentium II Xeon" Case 17 cputype = "Pentium III" Case 28 cputype = "AMD Athlon Processor Family" Case 29 cputype = "AMD Duron Processor" Case 30 cputype = "AMD2900 Family" Case 31 cputype = "K6-2+" Case 130 cputype = "Itanium Processor" Case 176 cputype = "Pentium III Xeon" Case 177 cputype = "Pentium III Processor with Intel SpeedStep Technology" Case 178 cputype = "Pentium 4" Case 179 cputype = "Intel Xeon" Case 181 cputype = "Intel Xeon processor MP" Case 182 cputype = "AMD AthlonXP Family" Case 183 cputype = "AMD AthlonMP Family" Case 184 cputype = "Intel Itanium 2" Case 185 cputype = "AMD Opteron? Family" End Select Next 'This returns the current uptime (time since last reboot) of the system. Set colOperatingSystems = objWMIService.ExecQuery ("Select * from Win32_OperatingSystem") For Each objOS in colOperatingSystems dtmBootup = objOS.LastBootUpTime dtmLastBootupTime = WMIDateStringToDate(dtmBootup) dtmSystemUptime = DateDiff("h", dtmLastBootUpTime, Now) Uptime = dtmSystemUptime Next Function WMIDateStringToDate(dtmBootup) WMIDateStringToDate = CDate(Mid(dtmBootup, 5, 2) & "/" & Mid(dtmBootup, 7, 2) & "/" & Left(dtmBootup, 4) & " " & Mid (dtmBootup, 9, 2) & ":" & Mid(dtmBootup, 11, 2) & ":" & Mid(dtmBootup,13, 2)) End Function dim objFSO Set objFSO = CreateObject("Scripting.FileSystemObject") ' -- The heart of the create file script ----------------------- ' -- Creates the file using the value of strFile on Line 11 ' -------------------------------------------------------------- Set fileOutput = objFSO.CreateTextFile( "x.html", true ) 'Set fileOutput = objExplorer.Document 'This is the code for the web page to be displayed. fileOutput.WriteLine "<html>" fileOutput.WriteLine " <head>" fileOutput.WriteLine " <title>System Information for '" & WKID & "' </title>" fileOutput.WriteLine " </head>" fileOutput.WriteLine " <body bgcolor='#FFFFFF' text='#000000' link='#0000FF' vlink='000099' alink='#00FF00'>" fileOutput.WriteLine " <center>" fileOutput.WriteLine " <h1>System Information for " & WKID & "</h1>" fileOutput.WriteLine " <table border='0' cellspacing='1' cellpadding='1' width='95%'>" fileOutput.WriteLine " <tr><td background='" & ImgDir & "blue_spacer.gif'>" fileOutput.WriteLine " <table border='0' cellspacing='0' cellpadding='0' width='100%'>" fileOutput.WriteLine " <tr><td>" fileOutput.WriteLine " <table border='0' cellspacing='0' cellpadding='0' width='100%'>" fileOutput.WriteLine " <tr>" fileOutput.WriteLine " <td width='5%' align='left' valign='middle' background='" & ImgDir & "blue_spacer.gif'><img src='" & ImgDir & "write.gif'></td>" fileOutput.WriteLine " <td width='95%' align='left' valign='middle' background='" & ImgDir & "blue_spacer.gif'> <font color='#FFFFFF' size='5'>WKInfo - </font><font color='#FFFFFF' size='3'>General information on the Workstation.</font></td>" fileOutput.WriteLine " </tr>" fileOutput.WriteLine " <tr><td colspan='2' bgcolor='#FFFFFF'>" fileOutput.WriteLine " <TABLE width='100%' cellspacing='0' cellpadding='2' border='1' bordercolor='#c0c0c0' bordercolordark='#ffffff' bordercolorlight='#c0c0c0'>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD align='center' bgcolor='#d0d0d0' colspan='2'><b><h3>Date and Time</h3></b></TD></TR>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Date/Time</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & DateTime & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>System Uptime</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & Uptime & " hours</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Time Zone</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & Zone & " </i></td></tr>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD align='center' bgcolor='#d0d0d0' colspan='2'><b><h3>General Computer Information</h3></b></TD></TR>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Manufacturer</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & Manufacturer & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Model</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & Model & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>System Based</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & SysType & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Operating System</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & WKOS & " " & CSD & " " & Architecture & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Operating System Install Date</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & InstallDate & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>UserName</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & UserName & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Workstation Name</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & WKID & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Domain</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & Domain & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>System Drive</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & SysDrive & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>System Directory</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & SysDir & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Windows Directory</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & WinDir & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>ShadowStorage Allocated Space</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & Allocated & " MB</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>ShadowStorage Used Space</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & UsedSpace & " MB</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>ShadowStorage Max Space</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & MaxSpace & " MB</i></td></tr>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD align='center' bgcolor='#d0d0d0' colspan='2'><b><h3>General Hardware Information</h3></b></TD></TR>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>CPU</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & cputype & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Memory</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & TotalMemory & " MB</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Total HDD Space</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & TotalHDSpace & " GB</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Free HDD Space</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & FreeHDSpace & " GB</i></td></tr>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD align='center' bgcolor='#d0d0d0' colspan='2'><b><h3>General Video Card Information</h3></b></TD></TR>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Video Card</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & VideoCard & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Resolution</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & Resolution & "</i></td></tr>" fileOutput.WriteLine " <TR><TD width='30%' align='left' bgcolor='#e0e0e0'>Memory</TD><td width='70%' bgcolor=#f0f0f0 align=left><i>" & VideoMemory & " MB</i></td></tr>" 'This section lists all the current services and their status. fileOutput.WriteLine " <TR><TD align='center' bgcolor='#d0d0d0' colspan='2'><b><h3>Current Service Information</h3></b></TD></TR>" fileOutput.WriteLine " <tr><td colspan='2' bgcolor='#f0f0f0'>" fileOutput.WriteLine " <TABLE width='100%' cellspacing='0' cellpadding='2' border='1' bordercolor='#c0c0c0' bordercolordark='#ffffff' bordercolorlight='#c0c0c0'>" fileOutput.WriteLine " <TR><TD width='70%' align='center' bgcolor='#e0e0e0'><b>Service Name</b></td><TD width='30%' align='center' bgcolor='#e0e0e0'><b>Service State</b></td><tr>" Set colRunningServices = objWMIService.ExecQuery("Select * from Win32_Service") For Each objService in colRunningServices fileOutput.WriteLine " <TR><TD align='left' bgcolor='#f0f0f0'>" & objService.DisplayName & "</TD><td bgcolor=#f0f0f0 align=center><i>" & objService.State & "</i></td></tr>" wscript.echo " <TR><TD align='left' bgcolor='#f0f0f0'>" & objService.DisplayName & "</TD><td bgcolor=#f0f0f0 align=center><i>" & objService.State & "</i></td></tr>" Next fileOutput.WriteLine " </table>" fileOutput.WriteLine " </td></tr>" 'This section lists all the current running processes and some information. fileOutput.WriteLine " <TR><TD align='center' bgcolor='#d0d0d0' colspan='2'><b><h3>Current Process Information</h3></b></TD></TR>" fileOutput.WriteLine " <tr><td colspan='2' bgcolor='#f0f0f0'>" fileOutput.WriteLine " <TABLE width='100%' cellspacing='0' cellpadding='2' border='1' bordercolor='#c0c0c0' bordercolordark='#ffffff' bordercolorlight='#c0c0c0'>" fileOutput.WriteLine " <TR><TD width='10%' align='center' bgcolor='#e0e0e0'><b>PID</b></td><TD width='35%' align='center' bgcolor='#e0e0e0'><b>Process Name</b></td><TD width='40%' align='center' bgcolor='#e0e0e0'><b>Owner</b></td><TD width='15%' align='center' bgcolor='#e0e0e0'><b>Memory</b></td></tr>" Set colProcessList = objWMIService.ExecQuery("Select * from Win32_Process") For Each objProcess in colProcessList colProperties = objProcess.GetOwner(strNameOfUser,strUserDomain) fileOutput.WriteLine " <TR><TD align='center' bgcolor='#f0f0f0'>" & objProcess.Handle & "</td><TD align='center' bgcolor='#f0f0f0'>" & objProcess.Name & "</td><TD align='center' bgcolor='#f0f0f0'>" & strUserDomain & "\" & strNameOfUser & "</td><TD align='center' bgcolor='#f0f0f0'>" & objProcess.WorkingSetSize/1024 & " kb</td><tr>" Next fileOutput.WriteLine " </table>" fileOutput.WriteLine " </td></tr>" 'This section lists all the currently installed software on the machine. fileOutput.WriteLine " <TR><TD align='center' bgcolor='#d0d0d0' colspan='2'><b><i>Installed Software</i></b></TD></TR>" fileOutput.WriteLine " <tr><td colspan='2' bgcolor='#f0f0f0'>" Set colSoftware = objWMIService.ExecQuery ("Select * from Win32_Product") For Each objSoftware in colSoftware fileOutput.WriteLine" <TABLE width='100%' cellspacing='0' cellpadding='2' border='1' bordercolor='#c0c0c0' bordercolordark='#ffffff' bordercolorlight='#c0c0c0'>" fileOutput.WriteLine" <tr><td width=30% align=center bgcolor='#e0e0e0'><b>Name</b></td><td width=30% align=center bgcolor='#e0e0e0'><b>Vendor</b></td><td width=30% align=center bgcolor='#e0e0e0'><b>Version</b></td></tr>" fileOutput.WriteLine" <tr><td align=center bgcolor=#f0f0f0>" & objSoftware.Name & "</td><td align=center bgcolor=#f0f0f0>" & objSoftware.Vendor & "</td><td align=center bgcolor=#f0f0f0>" & objSoftware.Version & "</td></tr>" fileOutput.WriteLine" <tr height=2><td height=10 align=center bgcolor=midnightblue colspan=3></td></tr>" fileOutput.WriteLine" </table>" Next fileOutput.WriteLine " </td></tr>" fileOutput.WriteLine " </table>" fileOutput.WriteLine " </td></tr>" fileOutput.WriteLine " </table>" fileOutput.WriteLine " </td></tr>" fileOutput.WriteLine " </table>" fileOutput.WriteLine " </td></tr>" fileOutput.WriteLine " </table>" fileOutput.WriteLine " <p><small></small></p>" fileOutput.WriteLine " </center>" fileOutput.WriteLine " </body>" fileOutput.WriteLine "<html>" fileOutput.close WScript.Quit

  Read the article

< Previous Page | 4 5 6 7 8