Search Results

Search found 18775 results on 751 pages for 'old hardware'.

Page 8/751 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >

  • Choosing hardware for Flash Media Server

    - by minaev
    Having read the answers in this discussion, I still would like to come up with the same question: What should I buy to run Flash Media Interactive Server 3.5? I just have slightly different boundary conditions. We plan to serve video to ca. 1,000 users simultaneously. It will be live stream, so the server will receive the stream in HD (1280x720), cache it, reformat to various other resolutions and send it to users. OS of choice is Linux, but if you say it should MS-DOS, so it will be... What would be a decent server for this task?

    Read the article

  • Suppliers for revision-controlled hardware, long-life motherboards?

    - by jacobsee
    Has anyone had good experience with suppliers of industrial computers, specifically 'long-life, revision-controlled' motherboards? I'm found a couple of likely candidates including ITOX, BCM, and DuroPC but haven't been able to find much in the way of independent review. I'm currently using off the shelf motherboards for an industrial data-acquisition system and am trying to eliminate the problem of rapid turnover/obsolescence of motherboards.

    Read the article

  • Laptop does not charge old or new battery with Old and New AC adapters.

    - by Jeff
    My Sager computer has been having a strange issue with the charging. For a long time it would be working perfectly as long as I was active on it. After I'd leave idle for a while it would suddenly decide it didn't want to use AC power anymore and would just discharge the battery until it shutdown because of low battery levels. Was not a huge deal to me since I just sent it to standby when done with it and it worked fine. Recently, however, it would not detect AC power while the battery was in. It ran from the battery just fine but until you powered it down, unplugged the battery, then plugged in the AC adapter it would not be on AC. In addition if I plug the battery back in after it's on AC power, it will see it but the battery won't charge though it can still discharge it. This is OS independent. I tried both a replacement battery and a replacement AC adapter. Neither solved my issue. I'm fairly comfortable opening and servicing a laptop but I don't know where to start. I'd like to avoid replacing my system board if possible. Any Ideas?

    Read the article

  • Minecraft server hosting hardware specifications [on hold]

    - by Andrew Wright
    I am planning on purchasing a server to rent off Minecraft game servers, largely to friends. I am planning on purchasing a 128GB RAM server to save on colocation costs (as I am likely to need more than 32GB and would have to rent 2U of space...) I am hoping for some advice about the processing power needed to deal with this level of RAM. The servers will be run in a shared environment on linux in a VM to make backups easier. The server I have in mind is dual CPU. I have been considering at the low end dual Xeon E5-2609V2 Quad-Core 2.5Ghz, and at the high end dual Xeon E5-2650V2 Eight-Core 2.6Ghz. The difference between these is 6.4 GT/s and 8 GT/s and £3000 for the lower spec server, £4300 for the higher spec. I was hoping I could get advice about whether it is worth paying for the extra/higher speed processor or if I would be wasting my money? Thank you for any help - I appreciate that this is not directly related to professional system administration.

    Read the article

  • Second video card (PCI) under Windows 7

    - by dbkk101
    I'm trying to get an old PCI video card (Diamond Stealth 2500) along with a normal PCI-E video card. In BIOS, there is a setting to switch between PEG/PCI or PCI/PEG on startup (PEG is PCI-E Graphics). When I use PCI/PEG only the old PCI card works, when I use the other one, only the new PEG card works. In PEG/PCI mode, Windows 7 recognizes the card and shows it in Device Manager as Standard VGA adapter, but it shows a warning for the device ("This device cannot start. (Code 10)").

    Read the article

  • Get Hardware Information for HWs that is not installed

    - by Isaac
    I am pretty sure how to retrieve hardware information with WMI classes. but WMIs have a big limitation: They Just can get information for installed hardwares. I need to retrieve information about CPU (model,speed,etc..),Video Card, Sound Card, USB Ports, etc. I found a really good software (HWiNFO) that can do this even the drivers for hardware parts is not installed. It seems that HWiNFO uses a internal database to give a name for each hardware part. So is there any free library/DLL/component that can do this in Windows XP or higher Note: Although HWiNFO SDK seems good, it's not free. So it doesn't exist! ;) I need a free library.

    Read the article

  • Is this possible to re-duplicate the hardware signal on Linux?

    - by Ted Wong
    Since that every things is a file on the UNIX system. If I have a hardware, for example, a mouse, move from left corner to right corner, it should produce some kinds of file to communicate with the system. So, if my assumption is correct, is this possible to do following things: Capture the raw data, which is about moving mouse cursor from left corner to right corner? Reduplicate the raw data, using a program, same producing speed, and data, in order to "redo" moving mouse cursor from left corner to right corner

    Read the article

  • How do I toggle the wifi hardware switch for a Dell XPS 17 L702X?

    - by Sparhawk
    Every now and then, I disable my wireless via the menu icon in Ubuntu. Then, when I try to enable the wifi, it tells me that "wireless is disabled" or "wireless is disabled by hardware switch". There is a red icon on the F2 key that looks like a wireless icon, and in Windows, pressing the (red) Fn key and F2 toggles the wifi. This does not work in Ubuntu, leaving me no clear way to turn wifi back on. How can I restart wifi in Ubuntu?

    Read the article

  • HFT strategy coding on hardware

    - by bsobaid
    Hardware accelaration and embedded programming has mostly been used so far to parse datafeed and/or to route orders to exchange. Have there been attempts to write simpler HFT strategies such as equity market-making in hardware? Have they been successful? Which companies are doing this and what kind of programming model is used?

    Read the article

  • How To Go About Updating Old C Code

    - by Ben313
    Hello: I have been working on some 10 year old C code at my job this week, and after implementing a few changes, I went to the boss and asked if he needed anything else done. Thats when he dropped the bomb. My next task was to go through the 7000 or so lines and understand more of the code, AND, to modularize the code somewhat. I asked him how he would like the source code modularized, and he said to start putting the old C code into c++ classes. Being a good worker, I nodded my head yes, and went back to my desk, where I sit now, wondering how in the world to take this code, and "modularize" it. Its already in 20 source files, each with its own purpose and function. in addition, there are three "main" structs. each of these stuctures has 30 plus fields, many of them being other, smaller sturcts. Its a complete mess to try to understand, but almost every single function in the program is passed a pointer to one of the structs, and uses the struct heavily. Is there any clean way for me to shoehorn this into classes? I am resolved to do it if it can be done, I just have no idea how to begin.

    Read the article

  • Sun Ray Hardware Last Order Dates & Extension of Premier Support for Desktop Virtualization Software

    - by Adam Hawley
    In light of the recent announcement  to end new feature development for Oracle Virtual Desktop Infrastructure Software (VDI), Oracle Sun Ray Software (SRS), Oracle Virtual Desktop Client (OVDC) Software, and Oracle Sun Ray Client hardware (3, 3i, and 3 Plus), there have been questions and concerns regarding what this means in terms of customers with new or existing deployments.  The following updates clarify some of these commonly asked questions. Extension of Premier Support for Software Though there will be no new feature additions to these products, customers will have access to maintenance update releases for Oracle Virtual Desktop Infrastructure and Sun Ray Software, including Oracle Virtual Desktop Client and Sun Ray Operating Software (SROS) until Premier Support Ends.  To ensure that customer investments for these products are protected, Oracle  Premier Support for these products has been extended by 3 years to following dates: Sun Ray Software - November 2017 Oracle Virtual Desktop Infrastructure - March 2017 Note that OVDC support is also extended to the above dates since OVDC is licensed by default as part the SRS and VDI products.   As a reminder, this only affects the products listed above.  Oracle Secure Global Desktop and Oracle VM VirtualBox will continue to be enhanced with new features from time-to-time and, as a result, they are not affected by the changes detailed in this message. The extension of support means that customers under a support contract will still be able to file service requests through Oracle Support, and Oracle will continue to provide the utmost level of support to our customers as expected,  until the published Premier Support end date.  Following the end of Premier Support, Sustaining Support remains an 'indefinite' period of time.   Sun Ray 3 Series Clients - Last Order Dates For Sun Ray Client hardware, customers can continue to purchase Sun Ray Client devices until the following last order dates: Product Marketing Part Number Last Order Date Last Ship Date Sun Ray 3 Plus TC3-P0Z-00, TC3-PTZ-00 (TAA) September 13, 2013 February 28, 2014 Sun Ray 3 Client TC3-00Z-00 February 28, 2014 August 31, 2014 Sun Ray 3i Client TC3-I0Z-00 February 28, 2014 August 31, 2014 Payflex Smart Cards X1403A-N, X1404A-N February 28, 2014 August 31, 2014 Note the difference in the Last Order Date for the Sun Ray 3 Plus (September 13, 2013) compared to the other products that have a Last Order Date of February 28, 2014. The rapidly approaching date for Sun Ray 3 Plus is due to a supplier phasing-out production of a key component of the 3 Plus.   Given September 13 is unfortunately quite soon, we strongly encourage you to place your last time buy as soon as possible to maximize Oracle's ability fulfill your order. Keep in mind you can schedule shipments to be delivered as late as the end of February 2014, but the last day to order is September 13, 2013. Customers wishing to purchase other models - Sun Ray 3 Clients and/or Sun Ray 3i Clients - have additional time (until February 28, 2014) to assess their needs and to allow fulfillment of last time orders.  Please note that availability of supply cannot be absolutely guaranteed up to the last order dates and we strongly recommend placing last time buys as early as possible.  Warranty replacements for Sun Ray Client hardware for customers covered by Oracle Hardware Systems Support contracts will be available beyond last order dates, per Oracle's policy found on Oracle.com here.  Per that policy, Oracle intends to provide replacement hardware for up to 5 years beyond the last ship date, but hardware may not be available beyond the 5 year period after the last ship date for reasons beyond Oracle's control. In any case, by design, Sun Ray Clients have an extremely long lifespan  and mean time between failures (MTBF) - much longer than PCs, and over the years we have continued to see first- and second generations of Sun Rays still in daily use.  This is no different for the Sun Ray 3, 3i, and 3 Plus.   Because of this, and in addition to Oracle's continued support for SRS, VDI, and SROS, Sun Ray and Oracle VDI deployments can continue to expand and exist as a viable solution for some time in the future. Continued Availability of Product Licenses and Support Oracle will continue to offer all existing software licenses, and software and hardware support including: Product licenses and Premier Support for Sun Ray Software and Oracle Virtual Desktop Infrastructure Premier Support for Operating Systems (for Sun Ray Operating Software maintenance upgrades/support)  Premier Support for Systems (for Sun Ray Operating Software maintenance upgrades/support and hardware warranty) Support renewals For More Information For more information, please refer to the following documents for specific dates and policies associated with the support of these products: Document 1478170.1 - Oracle Desktop Virtualization Software and Hardware Lifetime Support Schedule Document 1450710.1 - Sun Ray Client Hardware Lifetime schedule Document 1568808.1 - Document Support Policies for Discontinued Oracle Virtual Desktop Infrastructure, Sun Ray Software and Hardware and Oracle Virtual Desktop Client Development For Sales Orders and Questions Please contact your Oracle Sales Representative or Saurabh Vijay ([email protected])

    Read the article

  • Bad disks in ancient server

    - by Joel Coel
    I have a 1998-era Netware 3.12 server that runs everything on our campus: general ledger, purchasing, payroll, student information, grades, you name it. The server has an Adaptec RAID controller with two volumes: RAID 1, 2 17GB scsi disks, Seagate ST318417W RAID 5, 3 4GB scsi disks, 2 Seagate ST34573W and 1 ST34572W. We are currently in the early stages of a project to replace this system, but you don't just jump into a new system like that and so I need to keep this server running until at least November 2011. This week we had not one but two hard drives fail. Thankfully they are from different volumes and we're able to keep running for the moment, but given the close nature of these failures I have serious doubts that I'll be able to avoid catastrophic failure from this server through the November target as is without restoring the RAID redundancy — it'll only take one more drive failure anywhere and I'm completely hosed. We are fortunate enough to have exact match "spares" lying around for both drives, but the spares are in unknown condition. I tried swapping just them in, but the RAID controller isn't smart enough to handle this and it renders the system unbootable. As for the RAID controller itself, there is utility I can get into during POST via a Ctrl-A shortcut, but I can't do much useful from there. To actually manage volumes I must first boot in to Netware, at which point I can use CI/O Array Management Software Version 2.0 to actually look at volume information. I suspect that the normal way to manage things is to boot from a special floppy with the controller software on it, but that floppy is long gone. Going through the options in the RAID software, I think the only supported way to replace a disk in an existing RAID volume is to physically add the disk, boot up and configure it as a "spare" for a volume, force the volume to use the spare to replace an existing down disk (and at this point I'm only guessing) so that the down disk becomes the spare, repair the volume, remove the spare from the volume, and then shut down and remove the disk. Then start all over for the other failed disk. All this amounts to a lot of downtime, assuming I can even make it work and that my spares are any good. As for finding reliable spares, I have no clue where to even begin looking to find a new 4GB scsi drive, or even which exact scsi system I'm looking for, as it's gone through a few different iterations over time. Another option is to migrate this to a virtual machine (hyper-v), but all previous attempts we've made in this area have failed to get very far. When this machine was installed I was just graduating from high school, and so it requires lower level knowledge of netware and dos than I ever developed, or if I did have since forgotten (I'm not exactly a dos neophyte, either). Part of my problem is this is a high-use server, and taking it down for a few days to figure things out isn't gonna fly very well. As for the question, I'm looking for anything that might be helpful in this situation: a recommendation on a place to find good spares from this era, personal experience repairing RAID volumes using a similar controller or building a hyper-v vm from an old netware server, a line on a floppy with better software for the RAID controller, recommendation on a good Novell consultant in Nebraska that would be able to put things right, a whole other option I haven't considered yet, etc. Update: For backups, we have good (recently verified via restore) backups of the data only -- nothing for the software that actually runs things. Update 2: Just a progress report that I currently have a working Netware 3.12 install in VMWare Virtual Server 2.0, thanks largely to the guide I found here: http://cerbulescubogdan.blogspot.com/2010/11/novell-netware-312-on-vmware.html The next steps are preparing empty netware volumes to match the additional volumes on my existing server, taking a dump of everything on the C:\ drive and netware volumes on my existing server, and figuring out from that information what modules need added to netware, installing my licenses (we do still have that disk, if it's any good), and moving data over. I have approval to bring the server down for a week after the first of the year (sadly not before), so, aside from creating empty volumes, the rest of the work will have to wait until then. Final Update (Jan 5, 2011): I was able to get spares working in both raid arrays without data loss this week. Both are now listed by the controller as "FAULT TOLLERANT" (yay!). I was also able to build on the progress from my last update and now have a functional "spare" server in VMWare Server 2.0. The spare can run and use our erp software, but I can't put it into production because I can't (yet) print from that box (and I have no idea why). Even so, this VM will do in a pinch if I have no other choice, and between it and the repaired RAID arrays I'm comfortable pushing on until I can junk the machine in November.

    Read the article

  • is there anyway to clean up old svn directories and files from old source code tree

    - by oo
    i have been sent a directory tree of source code that i want to import into my subversion repository. The issue is that at some point this code was in a different subversion repository. There are a huge number of directories and subdirectories and i basically want to clean up all of the subversion .svn folders before i attempt to import to a new repository and i dont want svn to get confused. is there anyway to clean out a directory structure to remove all svn references?

    Read the article

  • Archive old files

    - by Victor
    I am new to SVN. I have a lot of old, unused files that I want to archive or copy to a different repository or directory. How can I archive these files and keep the history of their revisions?

    Read the article

  • Old files on computer not visible after upgrade

    - by Srinivasan
    I recently upgraded Ubuntu OS to 12.04.01 version by selecting the option to upgrade and preserve old files. After installation, I am not able to view my old files on the computer. Can anyone help to retrieve all the old files and make it available with the new installation? The computer hard disk shows that it still has the capacity nearly full with all my old files. Netbook Acer AOA150 model. Thanks in advance. Srinivasan

    Read the article

  • What features of old computers helped you learn to be a better programmer?

    - by David Cary
    What features of old computers helped you learn to be a better programmer -- but don't seem to be available on new computers? I imagine that, while educational, you are really glad some features are gone, such as programs ran so slowly that I could almost see each pixel being plotted, so I got a visceral feel for the effect of various optimizations. I imagine other features you may be a little nostalgic for, such as I could turn on the computer, and write a short program that printed "Hello, World" on the printer, before ever "booting" a "disk". (I'm hoping that this is constructive enough to avoid the fate of the " What have we lost from computers 20 years ago ?" question).

    Read the article

  • Is U.P.S necessary to have for PC?

    - by Jitendra vyas
    otherwise can my PC component ( Monitor, Motherboard, RAM, HDD, CPU, SMPS) get damage dues to suddenly power gone and come and due to power fluctuation. or it's only needed to shut down windows Properly. Can i face both Hardware and Software problems without UPS?

    Read the article

  • Problems with the colors on my screen. How can I check if it's a hardware problem?

    - by Ingo Gerth
    On my EEE PC netbook some colors are not displayed properly. Specifically, dark gradients such as in the window title do not look very smooth, but rather look like a sequence of a couple of different colors. This is especially visible when opening a menu, for example the "File" menu in Firefox. As you know this one is black, and it looks terrible on my screen. It is not just black, but the colors look really graded and far from a smooth gradient or anything. Now I am wondering: Is this a hardware or software issue? And how can I check this? If it should be a fixable problem I think it would be worth another question. Note that I am using Natty. If my problem description is not good enough I can try to take a photo.

    Read the article

  • Reliable way of generating unique hardware ID

    - by mr.b
    Question: what's the best way to accomplish following. I have to come up with unique ID for each networked client, such that: it (ID) should persist once client software is installed on target computer, and should continue to persist if software is re-installed on same computer and same OS installment, it should not change if hardware configuration is modified in most ways (except changing the motherboard) When hard drive with client software installed is cloned to another computer with identical hardware configuration (or, as similar as possible), client software should be aware of that change. A little bit of explanation and some back-story: This question is basically age old question that also touches topic of software copy-protection, as some of mechanisms used in that area are mentioned here. I should be clear at this point that I'm not looking for a copy-protection scheme. Please, read on. :) I'm working on a client-server software that is supposed to work in local network. One of problems I have to solve is to identify each unique client in network (not so much of a problem), so that I can apply certain attributes to every specific client, retain and enforce those attributes during deployment lifetime of a specific client. While I was looking for a solution, I was aware of following: Windows activation system uses some kind of heavy fingerprinting mechanism, that is extremely sensitive to hardware modifications, Disk imaging software copies along all Volume IDs (tied to each partition when formatted), and custom, uniquely generated IDs during installation process, during first run, or in any other way, that is strictly software in its nature, and stored in registry or on hard drive, so it's very easy to confuse two Obvious choice for this kind of problem would be to find out BIOS identifiers (not 100% sure if this is unique through identical motherboard models, though), as that's the only thing I can rely on, that isn't duplicated, transferred by cloning, and that can't be changed (at least not by using some user-space program). Everything else fails as either being not reliable (MAC cloning, anyone?), or too demanding (in terms that it's too sensitive to configuration changes). Am I missing something obvious here? Sub-question that I'd like to ask is, am I doing it correctly, architecture-wise? Perhaps there is a better tool for task that I have to accomplish... Another approach I had in mind is something similar to handshake mechanism, where server maintains internal lookup table of connected client IDs (which can be even completely software-based and non-unique at any given moment), and tells client to come up with different ID during handshake, if duplicate ID is provided upon connection. That approach, unfortunately, doesn't play nicely with one of requirements to tie attributes to specific client during lifetime.

    Read the article

  • What is a hardware-id?

    - by Rob
    Some forums that I regularly visit sell premium programs, and to prevent them from being leaked they use hardware-id authentication. That is, first they send you a program to run to grab your HWID, you tell them your HWID, they store it in a database, then they send you the actual program. If your HWID isn't in the database, the program won't run. So what is Hardware-ID, and how is it generated? Why is it that my HWID is different depending on the programmer that sends me a HWID-grabber?

    Read the article

  • Simple hardware RNG

    - by roygbiv
    I made a tongue-in-cheek comment to this question about making a hardware RNG. Does anyone know of any simple plans or can anyone descibe a simple hardware based RNG and the software to drive it? Go to Radio Shack. Buy a diode, an NTR resistor, a capacitor and serial cable. Cut off the end of the serial cable that does not fit on your computer. Solder the diode and resistor in series between pins DTR and DSR of the cable. Solder the capacitor between DSR and TXD pins. Write a small C program to do the following: Set DTR to 1. Start Timer. Monitor DSR until it goes to 1. Stop Timer. Calculate resistance from elapsed time. Retreive serveral bits from that value to use as part of random number. Repeat until enough bits have accumulated.

    Read the article

  • Page Rendering occurs blank page because of Old Cookie

    - by user333177
    Hi! I am developing application using J2EE (JSF,RichFaces, Jetty/Glashfish). Sometimes when I click on some link I get nothing returned to the browser at all (blank page). But when i refresh the page all contents appears in page. After some trail and error i found that it is cookies problem: It happens bez some old cookie not deleted by browser so this problem occurs. We also change web.xml file: but it creates more problem it doesn't maintain the session in application. Please friends if you have any suggestion on this problem help us.

    Read the article

  • Flex Datagrid File Download old value

    - by Vish
    Hi, We use a AIR client and WAMP server. Got a weird issue with Flex datagrid. When I download an image by double clicking on a datagrid row, the file gets downloaded correctly. But when I go on to select another row for download, even though the correct parameters are being passed, it again prompts download of old file. Upon cancelling that and trying again, it picks up the selected row. Not sure how to fix this issue, below is the datagrid code I am using, <mx:DataGrid x="10" y="10" id="ourDataGrid" visible="true" enabled="true" dataProvider="{fileList}" verticalScrollPolicy="on" selectionColor="#B7C6E7" itemClick="downloadFile(event)"> <mx:columns> <mx:DataGridColumn headerText="Name" dataField="@name" /> <mx:DataGridColumn headerText="LastName" dataField="@lastname" /> <mx:DataGridColumn headerText="FirstName" dataField="@firstname" /> </mx:columns> </mx:DataGrid>

    Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >