Search Results

Search found 278 results on 12 pages for 'sad sheep'.

Page 8/12 | < Previous Page | 4 5 6 7 8 9 10 11 12  | Next Page >

  • Is current SATA 6 gb/s equipment simply unreliable?

    - by korkman
    I have a 45-disk array of Seagate Barracuda 3 TB ST3000DM001 (yes these are desktop drives I'm aware of that) in a Supermicro sc847 JBOD, connected via LSI 9285. I have found a solution for the problem description below by reducing speed via MegaCli -PhySetLinkSpeed -phy0 2 -a0; for i in $(seq 48); do MegaCli -PhySetLinkSpeed -phy${i} 2 -a0; done and rebooting. The question remains: Is this typical for current 6 gb/s equipment? Is this the sad state of SATA storage? Or is some of my equipment (the sff-8088 cables come to mind) bad? The Problem was: Synchronizing HW RAID-6, disks kept offlining. Fetching SMART values reveiled that those which offlined did not increase powered-on hours anymore. That is, their firmware (CC4C) seems to crash. Digging into the matter by switching to Software RAID-6, with the disks passed-through, I got tons of kernel messages scattered across all disks, with 6 gb/s: sd 0:0:9:0: [sdb] Sense Key : No Sense [current] Info fld=0x0 sd 0:0:9:0: [sdb] Add. Sense: No additional sense information And finally, when a disk offlines: megasas: [ 5]waiting for 160 commands to complete ... megasas: [35]waiting for 159 commands to complete ... megasas: [155]waiting for 156 commands to complete ... megaraid_sas: pending commands remain after waiting, will reset adapter. Ugly controller reset here, then minutes later: megaraid_sas: Reset successful. sd 0:0:28:0: Device offlined - not ready after error recovery ... sd 0:0:28:0: [sdu] Unhandled error code sd 0:0:28:0: [sdu] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK sd 0:0:28:0: [sdu] CDB: Read(10): 28 00 23 21 2f 40 00 00 70 00 sd 0:0:28:0: [sdu] killing request Reduced speed to 3 gb/s like written above, all problems vanished.

    Read the article

  • Windows 7 boot issues

    - by Michael
    Ok, I tried to install linux and dual boot my laptop with 7 ultimate. I messed up. When I tried to boot to 7 it said no. Something along the lines of device not found. So I being young and stupid I uninstalled linux which I could boot into, and I still could not boot to windows. Next step was to run the startup fixes from the boot cd. Swing and a miss, I also ran the fixmbr and fixboot. Which brings us up to my current place. I installed 7 again on my blank partition in hopes I could access my other partion. No dice. So my question to yall is how can I fix my original filesystem or at least get to the stuff on it. In the new 7 install the old partion does not even have a drive letter. That is my sad story any help would be apreciated.

    Read the article

  • Wireless connection drops when wired computer starts a game.

    - by Skadlig
    Starting this week I have had a strange problem on my network. Some background of my setup: Internet is provided by a adsl-modem. A D-link Dir-600 router is hooked up to to adsl-modem. My computer is hooked up to the router using a cat-5 cable. My wife's computer is hooked up using a wireless usb dongle, TP-Link TL-WN821N. Both computers use windows 7 64-bit home premium. Up until this week everything was normal, we could for instance play Dungeons & Dragons Online together without any network issues. Now every time I start DDO or any other network game, for instance L4D, the whole wireless network drops. I have confirmed that it's not just her computer using an Samsung Galaxy Spica android phone. Shutting down the game on my end restores the wireless connection automagicly. My wife can start DDO without the net dropping but if I plug in a wireless network card in my computer and start up the game the connection drops. So it seems like something my computer, and my computer only, does when starting a game makes the wireless connection write a sad note and kill it self but for the life of me I can't figure out what that might be. I could hook her computer up using cat-5 but I would prefer not to do that. Does anyone have any suggestions as to what the problem might be, what I can do to fix it or what I should do to get more data regarding what is happening?

    Read the article

  • 10GE network: Is it still deadly expensive? Any options?

    - by BarsMonster
    Hi! I am building home cluster where I going to have about 16 nodes which can live with 1G ports, but I really want to have 10GE on file server & central node. It's all local, so no need for cabels longer than 3-5m. And ofcourse I want to spend as little money as possible (not going to spend more than whole cluster costs) :-) What are my options? 1) Legacy solution is to take some 24-48 port 1GE switch, and connect to file/central nodes via 4-8 aggregated links. This will work I guess, cost is very acceptable, but I am not sure if it's ok to use that much aggregated links. And ofcourse it would be hard to double bandwidth when needed... :-D 2) Switch with several 10GE uplink 'ports'. As far as I see, they all require modules which costs about 1000$, so I will need 4 10G modules, and 2 10GE cards... Smells like way more than 5000$+... 3) Connect file & central node via 2 10G cards directly, and put 4 quadport 1GE NICs on fileserver. I am saving on 2 10G modules and a switch, fileserver will have to do packet routing, but it's still gonna have alot of CPU's left :-) 4) Any other options? Infiniband? 5) Are MyriNet adaptors works fine? I guess there are no cheaper options? 6) Hmm... Scrap fileserver, put it all on central node and provide dedicated 1GE port for each of the nodes... This is sad...

    Read the article

  • Installing Windows 7 over PXE, preferably with domain autojoin

    - by Ivan Vucica
    At an educational non-profit, I've inherited a previously set-up Windows domain that, after the first reinstall of the machines, we ended up not using by simply not joining machines back into the domain. Over last summer, before the annual reinstall for shipping machines to the summer school, I toyed with the idea of installing Windows 7 over network, instead of just imaging the machines. It took a bit longer than I expected to figure out the basics; honestly, I expected that Windows would be more friendly for PXE installation out of the box. What I'm interested in is best practices for installing Windows 7 over PXE with domain autojoin. I'd love it if the whole setup could optionally be hosted on a UNIX based system as well. I've had some success by preparing an ISO using Windows Deployment Kit, and loading the ISO into memory. This was needed since I wanted a menu, and I think I couldn't get PXELINUX to chainload into Windows' bootloader. Unfortunately, I couldn't figure out much about customization of the Windows setup in that timeframe nor could I get Samba to work properly; studying the stuff ended up being too lengthy, especially the portion where I edited a disk image on Windows and copied it outside. WDK didn't make things easier by mounting the disk image into RAM, and writing it in its entirety when done with it, making me a very sad boy. I've recently found a different approach, too, that appears to be closer to Microsoft's original idea for netboot deployment and does not involve ISOs. So my question boils down to the following. What exact approach do you use for netbooting Windows 7 setup? How can Windows 7 setup be best customized to be completely unattended, including installation on specific system partition and not destroying the data partition, creation of passworded admin and default user, choice of MAC-address-based hostname, and joining a domain? As much details as possible for everyone's future reference would be appreciated. WDS isn't a bad choice, but if a Linux-based install can be used, that'd be better.

    Read the article

  • Reliable backup software for windows network/samba shares.

    - by Eli
    Hi All, I have a Win2003 server that works as a pdc for a number of XP boxes, and a couple related FreeBSD boxes. I need to back up roaming profiles, non-roaming profiles via network shares, local hard drive data, and files on the FreeBSD boxes via samba shares. I have tried Genie Backup Manager and Backup4All pro, and both have excellent features, but both also begin to fail disastrously with more than a few days use. Mostly, the errors seem to have been from the backup catalog getting out of synch with itself. Whatever it is, there is no excuse for a backup software that says it backed up files when it really didn't, or the log saying it backed up exactly the same file 10,000 times in a single run, or flat-out crashing, or any of the other myriad problems I've run into with these. Really sad for products that fill such an important need. Anyway, does anyone know of a backup software that works reliably and can do the following? Scheduled backups for multiple jobs, without a user logged in. Backup from local hard drives or network shares. Incremental backups. Thanks! Edit: Selected solution: I've added my (hopefully final) solution as an answer.

    Read the article

  • Microphone doesn't work

    - by mandy
    I'm having a trouble with my built in microphone. Even if I use headphone with mic, it doesn't really work. The weird thing is, if I clap the green lines of the speaker icon jumps, but if I speak it doesn't. I have also tried some recordings, but I can not hear myself and adjusting the volume didn't help at all. I tried to restore it, still no change. I have updated it in the device manager, but it said there that it's up to date and the devices are working properly. Until I decided to recover the whole system (wherein I pressed zero and switch on button) to my surprise, the settings became different, most programs were deleted, even my files. It's like it was formatted and I'm so sad that the mic was not fixed. I really don't know what to do now. My laptop model is Toshiba satellite m840. I want to it return to its settings/set up just before I Recover the system and bring back all the programs that we're installed and of course, most of all, to fix my microphone so I can use Skype again and other video calling application.. I hope someone could help me. Thanks a lot!

    Read the article

  • Hibernate & Sleep broken after IE 9 RTM installation in Windows 7 x64.

    - by AKa
    I have a question about hibernation. I installed Internet Explorer 9 RTM x64 on my Windows 7 x64 SP1 desktop machine. After this, computer don't entry the hibernation or (hybrid) sleep state properly. After I hibernate the computer the monitor become blank screen and the keyboard and mouse are inactive. But the machine is still running and there isn't any possibility to switch them off as only with power button. But this is recognized on next start as ineligible because of log entry with message “The previous system shutdown at xx:xx:xx on ?xx.?xx.?x was unexpected“ and menu with safe mode option. I’m clearly not sure if it has something to do with Internet Explorer installation, but I’m definitely guaranteed that before of this I never had some problems with hibernation or (hybrid) sleep. In Windows logs isn’t something suspect. I switched the hibernation off and on, installed new drivers for mainboard, graphic and network card, checked the hard disk, nothing was helpful. This is really sad, beacuse I don't like to switch the computer completely off because it takes longer to boot. Any suggestions?

    Read the article

  • How to convince Out of state resume filtering?

    - by sanksjaya
    Hello folks! Personally I've applied to quiet a handful of IT admin jobs inside my state and to the ones that are way far away. The sad part is I never miss to get an interview with the jobs in my state, but get a call once in a blue moon from jobs out of my state. Note: All the jobs are of similar nature. Recently one of my friends told me that "Applicants with local addresses are the ones that are even looked upon". How true is this? Does filtering take place at address level before qualifications? Is using a PO box on resume acceptable [one for each state like CA, TX, VA]? Any other suggestions to get calls from out of state? Thank you :) [wiki] =================== EDIT: Ignore my previous questions. PO box is out of my mind. So changed the title. Here are my new questions: 1. How true is this? Does filtering take place at address level before qualifications? 2. I'm ready to relocate anywhere on my own (Time/Money). How do I convince out-of-state resume filtering HR's? Sanks

    Read the article

  • Removed Old Domain Trust. Now Progress (9.1D) can't open DB File

    - by RLH
    My company has an old server, running Progress 9.1D on a Windows 2000 VM, which was used by our company OS (Vantage 6 by Epicor.) Vantage was our primary OS for a very long time. About 2 years ago, we migrated to a larger, corporate OS and we cancelled our service contract with Epicor. Yesterday, we removed an AD trust between the corporate domain and our old AD domain we used in the days of Vantage. After restarting the virtual server, I have been able to start the ProService for 9.1D Windows service, however, I can not get Vantage to start back up. When I run the application, I get the error in the message listed below. Transcript: ** Could not connect to server for database [progress db file], errno 0. (1432) How can I fix this? FYI, I haven't had to work with Progress in years and even then I wouldn't have considered myself a "novice"-- I'm even less knowledgeable than that title would suggest. Vantage had a lot of internal tools and I recall that Epicor support managed to prevent .pf scripts from being executed. If there was a Progress specific patch that needed to be applied, you had to do it within the Vantage software OR they had to remote into the machine to fix this. I may not be able to run a .pf script but I do know that I can log into the console-based server application. (Yes, I can't even recall which utility that was called. It is sad.) It's been a long time and I never had to digg into Progress that much. Please help and feel free to ask questions. If you need more info, I'll update this post.

    Read the article

  • I really need help resolving a Window Vista BSOD (Blue Screen Crash) on my desktop

    - by anonymous
    Hi, thanks for taking the time to read this. I'll get straight to the details. My desktop is on the fritz; it keeps going to blue screen with the stop message of 0x0000007E immediately after the loading bar of vista, right before transitioning to the account selection screen. My desktop runs on a dual-core 32-bit processor with windows Vista Home(?) installed. I have 3 GB of ram as two separate modules, a 1GB acer module and a 2GB geil module. I have an ati video card, unfortunately I cannot recall the exact name but the chipset is ATI and the manufacturer is Sapphire and the card is on the lower end. My hard drive is 320GB (i think) partitioned into two. The C:\ partition is red lined, while the D:\ partition is still pretty empty. As per the advice of my friend, i tried restarting the system with the graphics card removed. Upon failure, i repeated the process removing one RAM module one at a time, but the system still failed to load. Vista would attempt to repair the system and it would initially report that the system was fixed, but vista really failed to fix the problem. After removing the memory modules, vista started to report it's inability to fix the problem. I tried running on safe mode and the driver listing would always stop at crcdisk.sys. I ran memory diagnostics using the windows memory diagnostic tool found in the screen after vista's failed attempt to fix the problem with no luck. the problem details are as such: Problem Event Name : StartupRepairV2 Problem Signature 01: AutoFailover 02: (vista's version number?) 03: 6 04: 720907 05: 0x7e 06: 0x7e 07: 0 08: 2 09: WrpRepair 10: 0 OS Version: 6.0.6000.2.0.0.256.1 Locale ID 1033 any correct advice would be appreciated as i really need my pc to work so i can work on my projects. kinda sad, but i'm college of computer science and i have no idea what to do :P

    Read the article

  • parallelizing code using openmp

    - by anubhav
    Hi, The function below contains nested for loops. There are 3 of them. I have given the whole function below for easy understanding. I want to parallelize the code in the innermost for loop as it takes maximum CPU time. Then i can think about outer 2 for loops. I can see dependencies and internal inline functions in the innermost for loop . Can the innermost for loop be rewritten to enable parallelization using openmp pragmas. Please tell how. I am writing just the loop which i am interested in first and then the full function where this loop exists for referance. Interested in parallelizing the loop mentioned below. //* LOOP WHICH I WANT TO PARALLELIZE *// for (y = 0; y < 4; y++) { refptr = PelYline_11 (ref_pic, abs_y++, abs_x, img_height, img_width); LineSadBlk0 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk0 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk0 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk0 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk1 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk1 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk1 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk1 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk2 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk2 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk2 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk2 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk3 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk3 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk3 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk3 += byte_abs [*refptr++ - *orgptr++]; } The full function where this loop exists is below for referance. /*! *********************************************************************** * \brief * Setup the fast search for an macroblock *********************************************************************** */ void SetupFastFullPelSearch (short ref, int list) // <-- reference frame parameter, list0 or 1 { short pmv[2]; pel_t orig_blocks[256], *orgptr=orig_blocks, *refptr, *tem; // created pointer tem int offset_x, offset_y, x, y, range_partly_outside, ref_x, ref_y, pos, abs_x, abs_y, bindex, blky; int LineSadBlk0, LineSadBlk1, LineSadBlk2, LineSadBlk3; int max_width, max_height; int img_width, img_height; StorablePicture *ref_picture; pel_t *ref_pic; int** block_sad = BlockSAD[list][ref][7]; int search_range = max_search_range[list][ref]; int max_pos = (2*search_range+1) * (2*search_range+1); int list_offset = ((img->MbaffFrameFlag)&&(img->mb_data[img->current_mb_nr].mb_field))? img->current_mb_nr%2 ? 4 : 2 : 0; int apply_weights = ( (active_pps->weighted_pred_flag && (img->type == P_SLICE || img->type == SP_SLICE)) || (active_pps->weighted_bipred_idc && (img->type == B_SLICE))); ref_picture = listX[list+list_offset][ref]; //===== Use weighted Reference for ME ==== if (apply_weights && input->UseWeightedReferenceME) ref_pic = ref_picture->imgY_11_w; else ref_pic = ref_picture->imgY_11; max_width = ref_picture->size_x - 17; max_height = ref_picture->size_y - 17; img_width = ref_picture->size_x; img_height = ref_picture->size_y; //===== get search center: predictor of 16x16 block ===== SetMotionVectorPredictor (pmv, enc_picture->ref_idx, enc_picture->mv, ref, list, 0, 0, 16, 16); search_center_x[list][ref] = pmv[0] / 4; search_center_y[list][ref] = pmv[1] / 4; if (!input->rdopt) { //--- correct center so that (0,0) vector is inside --- search_center_x[list][ref] = max(-search_range, min(search_range, search_center_x[list][ref])); search_center_y[list][ref] = max(-search_range, min(search_range, search_center_y[list][ref])); } search_center_x[list][ref] += img->opix_x; search_center_y[list][ref] += img->opix_y; offset_x = search_center_x[list][ref]; offset_y = search_center_y[list][ref]; //===== copy original block for fast access ===== for (y = img->opix_y; y < img->opix_y+16; y++) for (x = img->opix_x; x < img->opix_x+16; x++) *orgptr++ = imgY_org [y][x]; //===== check if whole search range is inside image ===== if (offset_x >= search_range && offset_x <= max_width - search_range && offset_y >= search_range && offset_y <= max_height - search_range ) { range_partly_outside = 0; PelYline_11 = FastLine16Y_11; } else { range_partly_outside = 1; } //===== determine position of (0,0)-vector ===== if (!input->rdopt) { ref_x = img->opix_x - offset_x; ref_y = img->opix_y - offset_y; for (pos = 0; pos < max_pos; pos++) { if (ref_x == spiral_search_x[pos] && ref_y == spiral_search_y[pos]) { pos_00[list][ref] = pos; break; } } } //===== loop over search range (spiral search): get blockwise SAD ===== **// =====THIS IS THE PART WHERE NESTED FOR STARTS=====** for (pos = 0; pos < max_pos; pos++) // OUTERMOST FOR LOOP { abs_y = offset_y + spiral_search_y[pos]; abs_x = offset_x + spiral_search_x[pos]; if (range_partly_outside) { if (abs_y >= 0 && abs_y <= max_height && abs_x >= 0 && abs_x <= max_width ) { PelYline_11 = FastLine16Y_11; } else { PelYline_11 = UMVLine16Y_11; } } orgptr = orig_blocks; bindex = 0; for (blky = 0; blky < 4; blky++) // SECOND FOR LOOP { LineSadBlk0 = LineSadBlk1 = LineSadBlk2 = LineSadBlk3 = 0; for (y = 0; y < 4; y++) //INNERMOST FOR LOOP WHICH I WANT TO PARALLELIZE { refptr = PelYline_11 (ref_pic, abs_y++, abs_x, img_height, img_width); LineSadBlk0 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk0 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk0 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk0 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk1 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk1 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk1 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk1 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk2 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk2 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk2 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk2 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk3 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk3 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk3 += byte_abs [*refptr++ - *orgptr++]; LineSadBlk3 += byte_abs [*refptr++ - *orgptr++]; } block_sad[bindex++][pos] = LineSadBlk0; block_sad[bindex++][pos] = LineSadBlk1; block_sad[bindex++][pos] = LineSadBlk2; block_sad[bindex++][pos] = LineSadBlk3; } } //===== combine SAD's for larger block types ===== SetupLargerBlocks (list, ref, max_pos); //===== set flag marking that search setup have been done ===== search_setup_done[list][ref] = 1; } #endif // _FAST_FULL_ME_

    Read the article

  • Life Technologies: Making Life Easier to Manage

    - by Michael Snow
    12.00 Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} When we’re thinking about customer engagement, we’re acutely aware of all the forces at play competing for our customer’s attention. Solutions that make life easier for our customers draw attention to themselves. We tend to engage more when there is a distinct benefit and we can take a deep breath and accept that there is hope in the world and everything isn’t designed to frustrate us and make our lives miserable. (sigh…) When products are designed to automate processes that were consuming hours of our time with no relief in sight, they deserve to be recognized. One of our recent Oracle Fusion Middleware Innovation Award Winners in the WebCenter category, Life Technologies, has recently posted a video promoting their “award winning” solution. The Oracle Innovation Awards are part of the overall Oracle Excellence awards given to customers for innovation with Oracle products. More info here. Their award nomination included this description: Life Technologies delivered the My Life Service Portal as part of a larger Digital Hub strategy. This Portal is the first of its kind in the biotechnology service providing industry. The Portal provides access to Life Technologies cloud based service monitoring system where all customer deployed instruments can be remotely monitored and proactively repaired. The portal provides alerts from these cloud based monitoring services directly to the customer and to Life Technologies Field Engineers. The Portal provides insight into the instruments and services customers purchased for the purpose of analyzing and anticipating future customer needs and creating targeted sales and service programs. This portal not only provides benefits for Life Technologies internal sales and service teams but provides customers a central place to track all pertinent instrument information including: instrument service history instrument status and previous activities instrument performance analytics planned service visits warranty/contract information discussion forums social networks for lab management and collaboration alerts and notifications on all of the above team scheduling for instrument usage promote optional reagents required to keep instruments performing From their website The Life Technologies Instruments & Services Portal Helps You Save Time and Gain Peace of Mind Introducing the new, award-winning, free online tool that enables easier management of your instrument use and care, faster response to requests for service or service quotes, and instant sharing of key instrument and service information with your colleagues. Now – this unto itself is obviously beneficial for their customers who were previously burdened with having to do all of these tasks separately, manually and inconsistently by nature. Now – all in one place and free to their customers – a portal that ties it all together. They now have built the platform to give their customers yet another reason to do business with them – Their headline on their product page says it all: “Life is now easier to manage - All your instrument use and care in one place – the no-cost, no-hassle Instruments and Services Portal.” Of course – it’s very convenient that the company name includes “Life” and now can also promote to their clients and prospects that doing business with them is easy and their sophisticated lab equipment is easy to manage. In an industry full of PhD’s – “Easy” isn’t usually the first word that comes to mind, but Life Technologies has now tied the word to their brand in a very eloquent way. Between our work lives and family or personal lives, getting any mono-focused minutes of dedicated attention has become such a rare occurrence in our current era of multi-tasking that those moments of focus are highly prized. So – when something is done really well – so well that it becomes captivating and urges sharing impulses – I take notice and dig deeper and most of the time I discover other gems not so hidden below the surface. And then I share with those I know would enjoy and understand. In the spirit of full disclosure, I must admit here that the first person I shared the videos below with was my daughter. She’s in her senior year of high school in the midst of her college search. She’s passionate about her academics and has already decided that she wants to study Neuroscience in college and like her mother will be in for the long haul to a PhD eventually. In a summer science program at Smith College 2 summers ago – she sent the family famous text to me – “I just dissected a sheep’s brain – wicked cool!” – This was followed by an equally memorable text this past summer in a research mentorship in Neuroscience at UConn – “Just sliced up some rat brain. Reminded me of a deli slicer at the supermarket… sorry I forgot to call last night…” So… needless to say – I knew I had an audience that would enjoy and understand these videos below and are now being shared among her science classmates and faculty. And evidently - so does Life Technologies! They’ve done a great job on these making them fun and something that will easily be shared among their customers social networks. They’ve created a neuro-archetypal character, “Ph.Diddy” and know that their world of clients in academics, research, and other institutions would understand and enjoy the “edutainment” value in this series of videos on their YouTube channel that pokes fun at the stereotypes while also promoting their products at the same time. They use their Facebook page for additional engagement with their clients and as another venue to promote these videos. Enjoy this one as well! More to be found here: http://www.youtube.com/lifetechnologies Stay tuned to this Oracle WebCenter blog channel. Tomorrow we'll be taking a look at another winner of the Innovation Awards, LADWP - helping to keep the citizens of Los Angeles engaged with their Water and Power provider.

    Read the article

  • Building Visual Studio Setup Projects with TFS 2010 Team Build

    - by Jakob Ehn
    One of the most common complaints from people starting to use Team Build is that is doesn’t support building Microsoft’s own Setup and Deployment project (*.vdproj). When creating a default build definition that compiles a solution containing a setup project, you’ll get the following warning: The project file "MyProject.vdproj" is not supported by MSBuild and cannot be built.   This is what the problem is all about. MSBuild, that is used for compiling your projects, does not understand the proprietary vdproj format defined by Microsoft quite some time ago. Unfortunately there is no sign that this will change in the near future, in fact the setup projects has barely changed at all since they were introduced. VS 2010 brings no new features or improvements hen it comes to the setup projects. VS 2010 does include a limited version of InstallShield which promises to be more MSBuild friendly and with more or less the same features as VS setup projects. I hope to get a closer look at this installer project type soon. But, how do we go about to build a Visual Studio setup project and produce an MSI as part of a Team Build process? Well, since only one application known to man understands the vdproj projects, we will have to installa copy of Visual Studio on the build server. Sad but true. After doing this, we use the Visual Studio command line interface (devenv) to perform the build. In this post I will show how to do this by using the InvokeProcess activity directly in a build workflow template. You’ll want to run build your setup projects after you have successfully compiled the projects.   Install Visual Studio 2010 on the build server(s)   Open your build process template /remember to branch or copy the xaml file before modifying it!)   Locate the Try to Compile the Project activity   Drop an instance of the InvokeProcess activity from the toolbox onto the designer, after the Run MSBuild for Project activity   Drop an instance of the WriteBuildMessage activity inside the Handle Standard Output section. Set the Importance property to Microsoft.TeamFoundation.Build.Client.BuildMessageImportance.High (NB: This is necessary if you want the output from devenv to show up in the build log when running the build with the default verbosity) Set the Message property to stdOutput   Drop an instance of the WriteBuildError activity to the Handle Error Output section Set the Message property to errOutput   Select the InvokeProcess activity and set the values of the parameters to:     The finished workflow should look like this:     This will generate the MSI files, but they won’t be copied to the drop location. This is because we are using devenv and not MSBuild, so we have to do this explicitly   Drop a Sequence activity somewhere after the Copy to Drop location activity.   Create a variable in the Sequence activity of type IEnumerable<String> and call it GeneratedInstallers   Drop a FindMatchingFiles activity in the sequence activity and set the properties to:     Drop a ForEach<String> activity after the FindMatchingFiles activity. Set the Value property to GeneratedInstallers   Drop an InvokeProcess activity inside the ForEach activity.  FileName: “xcopy.exe” Arguments: String.Format("""{0}"" ""{1}""", item, BuildDetail.DropLocation) The Sequence activity should look like this:     Save the build process template and check it in.   Run the build and verify that the MSI’s is built and copied to the drop location.   Note 1: One of the drawback of using devenv like this in a team build is that since all the output from the default compilations is placed in the Binaries folder, the outputs is not avaialable when devenv is invoked, which causes the whole solution to rebuild again. In TFS 2008, this was pretty simple to fix by using the CustomizableOutDir property. In TFS 2010, the same feature is not avaialble. Jim Lamb blogged about this recently, have a look at it if you have a problem with this: http://blogs.msdn.com/jimlamb/archive/2010/04/13/customizableoutdir-in-tfs-2010.aspx   Note 2: Although the above solution works, a better approach is to wrap this in a custom activity that you can use in your builds. I will come back to this in a future post.

    Read the article

  • Amazon Product Advertising API SOAP Namespace Changes

    - by Rick Strahl
    About two months ago (twowards the end of February 2012 I think) Amazon decided to change the namespace of the Product Advertising API. The error that would come up was: <ItemSearchResponse > was not expected. If you've used the Amazon Product Advertising API you probably know that Amazon has made it a habit to break the services every few years or so and I guess last month was about the time for another one. Basically the service namespace of the document has been changed and responses from the service just failed outright even though the rest of the schema looks fine. Now I looked around for a while trying to find a recent update to the Product Advertising API - something semi-official looking but everything is dated around 2009. Really??? And it's not just .NET - the newest thing on the sample/APIs is dated early 2011 and a handful of 2010 samples. There are newer full APIs for the 'cloud' offerings, but the Product Advertising API apparently isn't part of that. After searching for quite a bit trying to trace this down myself and trying some of the newer samples (which also failed) I found an obscure forum post that describes the solution of getting past the namespace issue. FWIW, I've been using an old version of the Product Advertising API using the old Microsoft WSE3 services (pre-WCF), which provides some of the WS* security features required by the Amazon service. The fix for this code is to explicitly override the namespace declaration on each of the imported service method signatures. The old service namespace (at least on my build) was: http://webservices.amazon.com/AWSECommerceService/2009-03-31 and it should be changed to: http://webservices.amazon.com/AWSECommerceService/2011-08-01 Change it on the class header:[Microsoft.Web.Services3.Messaging.SoapService("http://webservices.amazon.com/AWSECommerceService/2011-08-01")] [System.Xml.Serialization.XmlIncludeAttribute(typeof(Property[]))] [System.Xml.Serialization.XmlIncludeAttribute(typeof(BrowseNode[]))] [System.Xml.Serialization.XmlIncludeAttribute(typeof(TransactionItem[]))] public partial class AWSECommerceService : Microsoft.Web.Services3.Messaging.SoapClient { and on all method signatures:[Microsoft.Web.Services3.Messaging.SoapMethodAttribute("http://soap.amazon.com/ItemSearch")] [return: System.Xml.Serialization.XmlElementAttribute("ItemSearchResponse", Namespace="http://webservices.amazon.com/AWSECommerceService/2011-08-01")] public ItemSearchResponse ItemSearch(ItemSearch ItemSearch1) { Microsoft.Web.Services3.SoapEnvelope results = base.SendRequestResponse("ItemSearch", ItemSearch1); return ((ItemSearchResponse)(results.GetBodyObject(typeof(ItemSearchResponse), this.SoapServiceAttribute.TargetNamespace))); } It's easy to do with a Search and Replace on the above strings. Amazon Services <rant> FWIW, I've not been impressed by Amazon's service offerings. While the services work well, their documentation and tool support is absolutely horrendous. I was recently working with a customer on an old AWS application and their old API had been completely removed with a new API that wasn't even a close match. One old API call resulted in requiring three different APIs to perform the same functionality. We had to re-write the entire piece from scratch essentially. The documentation was downright wrong, and incomplete and so scattered it was next to impossible to follow. The examples weren't examples at all - they're mockups of real service calls with fake data that didn't even provide everything that was required to make same service calls work. Additionally there appears to be just about no public support from Amazon, only peer support which is sparse at best - and getting a hold of somebody at Amazon, even for pay seems to be mythical task. It's a terrible business model they have going. I can't see why anybody would put themselves through this sort of customer and development experience. Sad really, but an experience we see more and more these days. Nobody puts in the time to document anything anymore, leaving it to devs to figure this stuff out over and over again… </rant>© Rick Strahl, West Wind Technologies, 2005-2012Posted in CSharp  Web Services   Tweet !function(d,s,id){var js,fjs=d.getElementsByTagName(s)[0];if(!d.getElementById(id)){js=d.createElement(s);js.id=id;js.src="//platform.twitter.com/widgets.js";fjs.parentNode.insertBefore(js,fjs);}}(document,"script","twitter-wjs"); (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

    Read the article

  • How to make software development decisions based on facts

    - by Laila
    We love to hear stories about the many and varied ways our customers use the tools that we develop, but in our earnest search for stories and feedback, we'd rather forgotten that some of our keenest users are fellow RedGaters, in the same building. It was almost by chance that we discovered how the SQL Source Control team were using SmartAssembly. As it happens, there is a separate account (here on Simple-Talk) of how SmartAssembly was used to support the Early Access program; by providing answers to specific questions about how the SQL Source Control product was used. But what really got us all grinning was how valuable the SQL Source Control team found the reports that SmartAssembly was quickly and painlessly providing. So gather round, my friends, and I'll tell you the Tale Of The Framework Upgrade . <strange mirage effect to denote a flashback. A subtle background string of music starts playing in minor key> Kevin and his team were undecided. They weren't sure whether they could move their software product from .NET 2 to .NET 3.5 , let alone to .NET 4. You see, they were faced with having to guess what version of .NET was already installed on the average user's machine, which I'm sure you'll agree is no easy task. Upgrading their code to .NET 3.5 might put a barrier to people trying the tool, which was the last thing Kevin wanted: "what if our users have to download X, Y, and Z before being able to open the application?" he asked. That fear of users having to do half an hour of downloads (.followed by at least ten minutes of installation. followed by a five minute restart) meant that Kevin's team couldn't take advantage of WCF (Windows Communication Foundation). This made them sad, because WCF would have allowed them to write their code in a much simpler way, and in hours instead of days (as was the case with .NET 2). Oh sure, they had a gut feeling that this probably wasn't the case, 3.5 had been out for so many years, but they weren't sure. <background music switches to major key> SmartAssembly Feature Usage Reporting gave Kevin and his team exactly what they needed: hard data on their users' systems, both hardware and software. I was there, I saw it happen, and that's not the sort of thing a woman quickly forgets. I'll always remember his last words (before he went to lunch): "You get lots of free information by just checking a box in SmartAssembly" is what he said. For example, they could see how many CPU cores their customers were using, and found out that they should be making use of parallelism to take advantage of available cores. But crucially, (and this is the moral of my tale, dear reader), Kevin saw that 99% of SQL Source Control's users were on .NET 3.5 or above.   So he knew that they could make the switch and that is was safe to do so. With this reassurance, they could use WCF to not only make development easier, but to also give them a really nice way to do inter-process communication between the Source Control and the SQL Compare products. To have done that on .NET 2.0 was certainly possible <knowing chuckle>, but Microsoft have made it a lot easier with WCF. <strange mirage effect to denote end of flashback> So you see, with Feature Usage Reporting, they finally got the hard evidence they needed to safely make the switch to .NET 3.5, knowing it would not inconvenience their users. And that, my friends, is just the sort of thing we like to hear.

    Read the article

  • Love and Hate Outlook autocomplete, Outlook 2010/Exchange 2010

    - by Kay Sellenrode
    I think that almost every Exchange admin can concur with me that the Outlook autocomplete cache is one of those things you love but at the same time also hate. Users mostly love this function, except when it fails.Luckily since Outlook 2010 things got a little better and we got rid of the dreaded nk2 files.Outlook 2010 now includes a folder named "Suggested Contacts", all users you send an email to and that don't already have an contact object are saved in this suggested contacts folder.A lot of people thought this folder is also the source for the autocomplete cache, which would make it somewhat easy to manage, I wish the solution was that easy.Badly enough separate from the suggested contacts, outlook still maintains a cache for the autocomplete function. Let us say you run in to the following situation: John works for company A and is a popular contact for almost everyone in your organization.Now John quit his job at Company A and moved to Company B.Luckily John maintains your company as customer, but his email address is now changed from companyA.com to companyB.comSince you don't want to do any business with Company A anymore, you want to make sure none of your users accidentally mail to his old address.Now this is where the real fun starts, cause almost all of your 1000 users have mailed at least once with John.Resulting in the fact that every user has John most probably listed in their autocomplete cache.  I have run into sort like situations multiple times with several customers, which is always a pain.And of course this blog post is the result of one of those issues once again.I knew that with the Suggested contacts we could do more than previously, but still never spent time on it before.But today I thought lets nail this now and forever!!  Ok let's start of that things are different for every combination of outlook and exchange.I explain the procedure for Exchange 2010 SP1+ in combination with Outlook 2010.At first we want to get rid of all contact objects that contain [email protected] do this we need to be assigned to the RBAC role "Mailbox Import Export", which can be done through the Exchange Control panel.In my test environment I assigned this role to the Organization admins, but in real life you might want to add it to a custom role. Open the Exchange control panel by logging in to the ecp url, in my case https://ITFEX.itf.local/ECP, and make sure you selected your organization as management scope.Browse to Roles & Auditing, and open the properties for the organization management role group.click on the Add button to add a new role to the Organization Management role group, select the Mailbox Import Export role and click on add and OK to add it to the role.  Once you have assigned that role to your account you can open the Exchange Management Shell and execute the following command: Get-mailbox –resultsize unlimited | search-mailbox –targetmailbox "your.account" –targetfolder searchanddelete –loglevel full –logonly –searchquery "kind:contact AND [email protected]" This command will create a list with all mailboxes and any contacts that were found with an email address that contains [email protected], this list is then posted in the mailbox you specified at your.account in the folder searchanddelete.Now examine the report that was created and posted in the mailbox to see if it matches what you think it should match.My results looked like this:  When you're confident that the search includes all references and no false positives you can execute almost the same command, but this time with an delete action instead of the logonly. Get-mailbox –resultsize unlimited | search-mailbox –targetmailbox "your.account" –targetfolder searchanddelete –loglevel full –DeleteContent –searchquery "kind:contact AND [email protected]" Now most people would think this would remove the contact object from the suggested contacts, resulting in a removal from the autocomplete list.Sad but not true, to clean up the autocomplete list start Outlook with the command: "outlook /cleanautocompletecache" This will result in an empty cache, but luckily this is rebuild based on the suggested contacts, which now doesn't include the [email protected] contact anymore.

    Read the article

  • 5 Ways to Celebrate the Release of Internet Explorer 9

    - by David Wesst
    The day has finally come: Microsoft has released a web browser that is awesome. On Monday night, Microsoft officially introduced the world to the latest edition to its product family: Internet Explorer 9. That makes March 14, 2011 (also known as PI day) the official birthday of Microsoft’s rebirth in the world of web browsing. Just like any big event, you take some time to celebrate. Here are a few things that you can do to celebrate the return of Internet Explorer. 1. Download It If you’re not a big partier, that’s fine. The one thing you can do (and definitely should) is download it and give it a shot. Sure, IE may have disappointed you in the past, but believe me when I say they really put the effort in this time. The absolute least you can do is give it a shot to see how it stands up against your favourite browser. 2. Get yourself an HTML5 Shirt One of the coolest, if not best parts of IE9 being released is that it officially introduces HTML5 as a fully supported platform from Microsoft. IE9 supports a lot of what is already defined in the HTML5 technical spec, which really demonstrates Microsoft’s support of the new standard. Since HTML5 is cool on the web, it means that it is cool to wear it too. Head over to html5shirt.com and get yourself, or your staff, or your whole family, an HTML5 shirt to show the real world that you are ready for the future of the web. 3. HTML5-ify Something Okay, so maybe a shirt isn’t enough for you. Maybe you need start using HTML5 for real. If you have a blog, or a website, or anything out there on the web, celebrate IE9 adding some HTML5 to your site. Whether that is updating old code, adding something new, or just changing your WordPress theme, definitely take a look at what HTML5 can do for you. 4. Help Kill Old IE and Upgrade your Organization See this? This is sad. Upgrading web browsers in an large enterprise or organization is not a trivial task. A lot of companies will use the excuse of not having the resources to upgrade legacy web applications they were built for a specific version of IE and it doesn’t render correctly in legacy browsers. Well, it’s time to stop the excuses. IE9 allows you to define what version of Internet Explorer you would like it to emulate. It takes minimal effort for the developer, and will get rid of the excuses. Show your IT manager or software development team this link and show them how easy it is to make old code render right in the latest and greatest from the IE team. 5. Submit an Entry for DevUnplugged So, you’ve made it to number five eh? Well then, you must be pretty hardcore to make it this far down the list. Fine, let’s take it to the next level and build an HTML5 game. That’s right. A game. Like a video game. HTML5 introduces some amazing new features that can let you build working video games using HTML5, CSS3, and JavaScript. Plus, Microsoft is celebrating the launch of IE9 with a contest where you can submit an HTML5 game (or audio application) and have a chance to win a whack of cash and other prizes. Head here for the full scoop and rules for the DevUnplugged. This post also appears at http://david.wes.st

    Read the article

  • Head in the Clouds

    - by Tony Davis
    We're just past the second anniversary of the launch of Windows Azure. A couple of years' experience with Azure in the industry has provided some obvious success stories, but has deflated some of the initial marketing hyperbole. As a general principle, Azure seems to work well in providing a Service-Oriented Architecture for services in enterprises that suffer wide fluctuations in demand. Instead of being obliged to provide hardware sufficient for the occasional peaks in demand, one can hire capacity only when it is needed, and the cost of hosting an application is no longer a capital cost. It enables companies to avoid having to scale out hardware for peak periods only to see it underused for the rest of the time. A customer-facing application such as a concert ticketing system, which suffers high demand in short, predictable bursts of activity, is a great example of an application that would work well in Azure. However, moving existing applications to Azure isn't something to be done on impulse. Unless your application is .NET-based, and consists of 'stateless' components that communicate via queues, you are probably in for a lot of redevelopment work. It makes most sense for IT departments who are already deep in this .NET mindset, and who also want 'grown-up' methods of staging, testing, and deployment. Azure fits well with this culture and offers, as a bonus, good Visual Studio integration. The most-commonly stated barrier to porting these applications to Azure is the problem of reconciling the use of the cloud with legislation for data privacy and security. Putting databases in the cloud is a sticky issue for many and impossible for some due to compliance and security issues, the need for direct control over data, and so on. In the face of feedback from the early adopters of Azure, Microsoft has broadened the architectural choices to cater for a wide range of requirements. As well as SQL Azure Database (SAD) and Azure storage, the unstructured 'BLOB and Entity-Attribute-Value' NoSQL storage alternative (which equates more closely with folders and files than a database), Windows Azure offers a wide range of storage options including use of services such as oData: developers who are programming for Windows Azure can simply choose the one most appropriate for their needs. Secondly, and crucially, the Windows Azure architecture allows you the freedom to produce hybrid applications, where only those parts that need cloud-based hosting are deployed to Azure, whereas those parts that must unavoidably be hosted in a corporate datacenter can stay there. By using a hybrid architecture, it will seldom, if ever, be necessary to move an entire application to the cloud, along with personal and financial data. For example that we could port to Azure only put those parts of our ticketing application that capture and process tickets orders. Once an order is captured, the financial side can be processed in our own data center. In short, Windows Azure seems to be a very effective way of providing services that are subject to wide but predictable fluctuations in demand. Have you come to the same conclusions, or do you think I've got it wrong? If you've had experience with Azure, would you recommend it? It would be great to hear from you. Cheers, Tony.

    Read the article

  • Make the Time

    - by WonderOfItAll
    Took the little one to the pool tonight for swim lessons. Okay, Okay. They're not really lessons so much as they are "Hey, here's a few bucks, let me rent out a small section of your pool to swim around with my little one" Saw a dad at the pool. Bluetooth on, iPad in hand, and two year old somewhere around there. Saw a mom at the pool. Arguing with her five year old to NOT take a shower after swimming. Bluetooth on, iPad in hand, work laptop open on stadium seats. Her reasoning for not wanting the child to shower "Look, I have to get this stuff to the office by 6:30, we don't have time for you to shower. Let's go" Wait, isn't the whole point of this little experience called Mommy and Me (or, as in my case, Daddy and Me). Wherein Mommy/Daddy is supposed to spend time with little one. Not with the Bluetooth. Not with the work laptop. Dad (yeah, the same dad from earlier), in the pool. Bluetooth off (it's not waterproof or I'm sure he would've had it on), two year old in hand and iPad somewhere put away. Getting frustrated with kid because he won't 'perform' on command. Here's a little exchange Kid: "I don't wanna get in the water" Dad: "Well, we're here for 30 minutes, get in the water" Kid: "No, don't wanna" Dad: "Fine, I'm getting in" and, true to his word, in he goes, off to swim. Kid: Crying Dad: "Well, c'mon" Kid: Walking to stands Dad: Ignoring kid Kid: At stands Dad: Out of pool, drying off. Frustrated. Grabs bag, grabs kid, leaves How sad. It really seems like I am living in a generation of parents who view their children as one big scheduled distraction to another. It's almost like the dad was saying "Look, little 2 year old boy, I have a busy scheduled. Right now my Outlook Calendar tells me that I have 30 mins to spend with you, so, let's go kid: PERFORM because I have the time" Really? Can someone please tell me when the hell this happened? When did spending time with your kid, spending time with your family, spending time with your spouse, etc... become a distraction? I've seen people at work all day Tweeting throughout the day, checked in with Four Square, IM up and running constantly so they can 'stay in touch' only to see these same folks come home and be irritated because their kids or their spouse wants to connect with the. I've seen these very same people leave the house, go to the corner bar/store/you-name-the-place to be 'alone' only to find them there, plugged in, tweeting away, etc, etc, etc I LOVE technology. I love working with technology. But I also know that I am a human being. A person who, by very definition, is a social being. I needed social interactions and contact--and, no, I'm not talking about the Social Graph kind of connections, I'm talking about those interactions which, *GASP* involve eye to eye contact and human contact. A recent study found that the number one complaint of kids is that they feel they have to compete with technology for their parents time and attention. The number one wish from high school kids? That there parents would turn off the computer/tv/cell phone at dinner. This, coming from high school kids. Shouldn't that tell you a whole helluva lot? So, do yourself a favor tomorrow. Plug into technology all day. Throw yourself into it. Be passionate about what you do. When you walk through the door to your family, turn it all off for 30 mins and be there with your loved ones. If you can manage to play Angry Birds, I'm sure you can handle being disconnected for 30 minutes. Make the time

    Read the article

  • Why Apple’s New SDK Limitation is So Offensive

    - by TStewartDev
    I am not an Apple fanboy, nor have I ever been. However, I have owned a Mac, an iPod, and an iPhone in my lifetime, and for more than a decade, I have defended Apple against the untruths that the haters so enjoy spewing. I encouraged my wife to buy a MacBook when she needed a new laptop two years ago, and I often recommend them to my friends and relatives. I have proudly and happily used my first generation iPhone for nearly three years. Now, for the first time in well over ten years, I find myself ready to swear off Apple and encourage everyone I know to do the same. I was disappointed when Apple wouldn't allow native apps, but I still bought the iPhone. I've stomached their ambiguous app approval process even though it's apparent that Steve may just reject your app because he doesn't like you or feels threatened by you (I'm still lamenting the rejection of the Google Voice app). But, as a developer, I can no longer tolerate Apple's terms and the kind of totalitarian control they indicate Apple wants. In case you are not already familiar, Apple has dictated in their OS 4.0 SDK license agreement (the now infamous Section 3.3.1) that all apps developed for the iPhone must be coded in C, C++, or Objective C, and moreover, that using any cross-compiling platforms is a violation of the agreement. For those of you who aren't developers, let me try to illustrate why this angers those of us who are. Imagine you're a professional writer. You've had articles published in some journals and magazines, and you've got a couple popular books out there, too. You've got an idea for a new book, and so you take it to your publisher. Your publisher agrees that it's a good idea. "But," says the publisher, "we want to hold our books to a tighter standard so that our readers get the experience we want them to have. Therefore, from now on, all our writers may only use words from this list of the 10,000 most common English words. Furthermore, if you cite any other works or quote anyone, they must comply with that same list, or you'll have to rewrite the entire work as well in case our readers want to look up your citation." What do you do? If your work is a children's book, this probably isn't a big deal to you. If it's an autobiography, textbook, or even a novel, though, you're going to have a lot of trouble describing your content with only common words. It's going to take you longer to complete your book, too, since you'll be looking up less common words frequently to see if you can use them. You could always go to another publisher, but this one has the best ability to distribute your book. The next largest distributor can only do a quarter as much. You could abandon the project altogether, but then everyone loses. Isn't this a silly scenario? Who would put such a limitation on writers? Yet this is very much what Apple is doing. They are using their dominant position in the market to coerce developers to write their apps exclusively for the iPhone OS by making it too expensive to write for multiple platforms. It is at least a threefold attack, striking at Adobe who is set to release a compiler that lets Flash source be compiled to iPhone binaries; striking at Google whose Android platform stands the best chance at the moment of providing serious competition to the iPhone; and reinforcing their own strong position by keeping popular apps exclusively to iPhone. And while developers are already very upset about this, the sad fact is that most of us will cave and give in to Apple because consumers don't know any better. They will continue to buy Apple's toy forcing developers to play Apple's maniacal game in order to make any money, at least until Steve Jobs decides he doesn't like them or he intends to release a competing application (bye-bye OpenFeint). Apple has been kept in check on the desktop front by a very dominant Microsoft, but I'm afraid that their success with iPods, iTunes, and iPhones has created a monster that we may have to bear until it is slain by an anti-trust suit or dies with the retirement of Steve Jobs.

    Read the article

  • How do you deal with poor management [closed]

    - by Sybiam
    I come from a company where during a project, we saw the client 3 time during the whole project. We were never informed when did the client came in office in order to discuss with him about his requirements. I did setup redmine and told them that if they have any request they can post an issue there. But they never really used redmine to publish anything. They would instead: harass a team member on the phone at any time of the day or night hand us over sheets of paper with new requests or changes hand us over new design (graphical) They requested how much time it would take us to finish the project, I gave them a date and a week to test everything and deployment. I calculated that time taking into account the current features we had to do. And then blamed us that our deadline was wrong and that we lied. But the truth is that one week before that deadline they added a couple of monster feature from nowhere and that week were we were supposed to test and deploy, my friends spent all day in the office changing all little things. After that project, my friend got some kind of depression and got scared everytime his phone rang. They kind of used him as a communication proxy. After that project of hell, (every body got pissed off on that project) as far as I know the designer who was working with us left work after that project and she had some kind of issue too with managers. My team also started looking for work somewhere else. At first I tried to get things straight with management, I tried to make a meeting to discuss about the communication issues and so on.. What really pissed me off and made me leave that job for good is the following. Me: "We have to discuss about what went wrong on the last project. It's quite important" Him: "Lets talk about it in a week or two. Just make a list of all the things you did wrong" Me: "We already have a new project and we want to prevent what happened on the last project to happen again" Him: "Just do it and well have our meeting in a week, make a list of all the thing you did wrong." It kind of ended there then he organized a meeting at a moment I wasn't unable to come. My friend discussed with him and tried to explained him that we really had to discuss about organization issue on how to manage a project. And his answer was pretty much: "During the meeting I don't want to ear how you want to us to manage a project but I want to know what you guys did wrong" After that I felt it wasn't even worth it discussing anything since they weren't even ready listening to us. Found a new job and I'm pretty happy with my choice. I'd like to know how you'd handle such situation. Is there anything to do to solve communication problem? After that project my friend got a depression and some other employee had their down too as far as I know. I wonder what else we can do other than leave these place as soon as possible. Feel sad for the people that are still there and get screamed at just because they need money in order to eat and finding an other job like that isn't that easy. note I died a little when our boss asked us to make a list of things we (programmers) did wrong. This is probably the stupidest request I ever got. If everybody thinks they did everything right, it doesn't mean that there is no problems. Individual problem are rarely the big issue. Colleagues help each others and solve theses issues to prevent problems.

    Read the article

  • JavaFX Datagrid

    - by Chepech
    Hi All. Im in the verge of starting a new RIA development. We've been using Flex/Flash for the last 2 years but we were considering using a more OS approach so we though giving JavaFX a try since it seams the only solid option available. However after a couple of days of research we found out that there is not such thing as a datagrid for it, at least not in the core API. For those unfamiliar with Flex, a Datagrid is a component that allows you to display a collection of data in column-row layout (much like a HTML Table on steroids). The beauty of it is that you only need to worry about the data itself as the component does pretty much the rest (sorting, column dragging, etc). Im afraid to ask... but is there something slightly similar for JavaFX? We require nothing as fancy as Flex Datagrids/AdvancedDatagrids, we only require a easy, straight forward way to display grids of data that are able to have a little of interaction like clicking, sorting and that are able to display images, buttons, etc. without having to download a ton of different jars. If there isn´t something out there... This would be a shot in the back of the head to the idea of giving javaFx the chance to compete with flash on our project (which is sad). I really cant believe the SUN people didnt include something like this on the core API...

    Read the article

  • jQuery jqGrid TreeGrid not functionining properly

    - by Raul Agrait
    Hello. I am having trouble constructing a jqGrid TreeGrid using local data. This method works just fine as a regular grid if you comment out the treeGrid and ExpandColumn attributes, but once you add those to try to make it a tree grid, it doesn't create the tree grid, and it no longer sorts properly. jQuery(function(){ var gridOptions = { datatype: "local", height: 250, colNames: ['Name', 'Type', 'Last Modified On', 'Last Modified By'], colModel: [{name: 'name', index: 'name', width: 200, sorttype: 'text'}, {name: 'type', index: 'type', width: 200, sorttype: 'text'}, {name: 'modifiedon', index: 'modifiedon', width: 200, sorttype: 'date'}, {name: 'modifiedby', index: 'modifiedby', width: 200, sorttype: 'text'}], treeGrid: true, ExpandColumn: 'name', caption: "My Grid" }; jQuery("#treeGrid").jqGrid(gridOptions); var gridData = [ {name: "My File", type: "My File Type", modifiedon: "03/10/2010", modifiedby"Strong Sad", lft: "1", rgt: "8", level: "0"}, {name: "One of Everything", type: "Word Document", modifiedon: "02/12/2009", modifiedby: "Strong Bad", lft: "2", rgt: "5", level: "0"}, {name: "My Presentation", type: "PowerPoint", modifiedon: "01/23/2009", modifiedby: "The Cheat", lft: "3", rgt: "4", level: "0"} ]; for (var i = 0; i < gridData.length; i++) { jQuery("#treeGrid").jqGrid('addRowData', i + 1, gridData[i]); } });

    Read the article

  • Gmagick extension for php install -- how and where?

    - by Vivek Chandra
    Downloaded php-pear and tried installing gmagick extension by following the steps given in link "http://www.gerd-riesselmann.net/development/how-install-imagick-and-gmagick-ubuntu" The pecl gave an error -- gmagick-1.0.9b1$ pecl install gmagick Failed to download pecl/gmagick within preferred state "stable", latest release is version 1.0.9b1, stability "beta", use "channel://pecl.php.net/gmagick-1.0.9b1" to install install failed Tried adding the channel (no result)-- gmagick-1.0.9b1$ pecl channel-add http://pecl.php.net/package/gmagick/1.0.9b1 Error: No version number found in tag channel-add: invalid channel.xml file Found the link "http://pecl.php.net/package/gmagick" to download the php extension untar'd it to find the following files -- gmagick-1.0.9b1$ ls config.m4 gmagickdraw_methods.c gmagick_methods.c LICENSE php_gmagick_helpers.h README gmagick.c gmagick_helpers.c gmagickpixel_methods.c php_gmagick.h php_gmagick_macros.h Tried . / config.m4 only to find more errors gmagick-1.0.9b1$ . / config.m4 ./config.m4: line 1: syntax error near unexpected token `gmagick,' ./config.m4: line 1: `PHP_ARG_WITH(gmagick, whether to enable the gmagick extension,' Been at this since a day with no result.Read that gmagick is a swiss knife of image processing,sad that there isnt much documentation done on it or at least a proper how to install link anywhere. Badly need help. Thanks in advance.

    Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12  | Next Page >