Search Results

Search found 346 results on 14 pages for 'standby'.

Page 8/14 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14  | Next Page >

• What would be the optimal disk config for SQL Server 2008 R2?

  - by Kev

  We have a new Dell R710 server that came with the following storage configuration: 8 x 146GB SAS 10k 6Gbps disks 1 x Perc H700 Integrated Controller (2 x 4 disks - 2 ports each supporting 4 disks) What would be the optimal configuration if we were just after performance? What would be the optimal configuration if we were after performance but wanted data resilience. As per 2 above but with a hot standby disk? We plan to run Windows 2008 R2 and SQL Server 2008 R2. Maximising storage capacity isn't a prime concern.

  Read the article

• why does chkdsk always report errors on a bad shutdown

  - by rep_movsd

  Once in a while, Windows XP hangs on my laptop (usually when going into standby or hibernate and occasionally on startup) and I have to forcefully poweroff. Ususally chkdsk never runs automatically (I thought it should know that the partitions have nit been unmounted and do that). I religiously run chkdsk without /F after bad shutdowns like this, and invariably it reports that the drive has unfixed errors and must be checked with /F and I do that, and more often than not, the chdsk that runs on startup does not report fixing anything. I have had times in the past (and not only just on this system) when not running chkdsk leads to some strange errors like files not opening even though they exist and inability to save certain files, so I make it a point to always chkdsk after bad shutdown. I never understood why this is : Isnt the whole point of a journalling filesystem like NTFS to avoid file system corruption and endless chkdsks? I even tried once disabling write caching to see if it made any difference, but to no avail....

  Read the article

• What is this jumper for on my new motherboard?

  - by jasondavis

  I am building a new PC, I just got my motherboard in the mail today. It is a ASRock X58 Extreme 3. I am reading over the manual for it and one of the jumpers says this. There is a 3 pin jumper labeled 1 2 3, with pins 1 and 2 shorted by default it is "+5v" If I manually change it to short jumper pins 2 and 3 instead of 1 and 2 then it will be "+5vSB (standby) for PS/2 or USB wake up events. So I am confused as to exactly what this is for. Can someone explain what it means, why I would want one other the other?

  Read the article

• schedule a task to run every day within a time range?

  - by barlop

  How do I schedule a task to run once any time within a time range? and also, just once in a day without specifying a time? can windows task scheduler do it? and specifically, if my computer is off or on standby or hibernation at the time I want it to run it when it is on if it hasn't been run that day and the time has passed. I see an option to wake it to run the task , but could I then put it back to sleep? And i'd like to be able to as mentioned.. let it run when the computer is back on.

  Read the article

• Outlook 2007 VBA/Macro

  - by user27538

  Hi, I am a very basic user new to macros and vba. My problem is that I recive online orders to which i need to click an auto generated unique order hyperlink to confirm receipt of the order within a specified time period. This is a mundane task having to be on 'standby' and was wondering if there was a way to have this link automatically clicked when the email arrives. Just to reiterate the link has a unique reference and is different on each email. Please bare in mind that I am a very basic user and would probably require step by step instructions. Many thanks in advance

  Read the article

• Applications don't see mapped network drive after waking from sleep

  - by Chris

  I have a network share mapped as a drive letter on a Windows 7 PC that's part of a simple home network. When I wake the PC from sleep, Explorer sometimes says the drive is disconnected. Doubleclicking the drive connects it instantly, as far as Explorer is concerned. But some other applications don't see the drive unless I take additional steps (e.g., navigate to the drive in an "Open..." dialog). Is there any way to get the drive to be connected for all purposes immediately when resuming from standby? I've found the "Always wait for the network at computer startup and logon" item in Group Policy, but I'm not sure what the setting does or whether it would fix this problem. I have network discovery enabled and un-firewalled.

  Read the article

• Shrink Partition on Production Server

  - by Campo

  SO our production server was only setup with one large partition. I have setup a standby server and properly partitioned it. Now the boss wants the production environment's partition shrunk. It is an HP DL380 G5 We have 4 hot swap drives in a raid 5. How best should I go about doing this. Seems like a bad idea to me. Should I use windows or HP to do the partitioning? What should I be aware of in a production environment? The idea is to put the site (Inetpub) on a separate partition instead of the C: drive. How much downtime should I expect? Is this a terrible idea? Anything else I have missed?

  Read the article

• Computer wont POST after power outage

  - by aaron

  I had just turned my computer on and windows was loading when the power in my neighborhood went out. Normally, when I turn my computer on, the video card fan spins up, then slows down, POST and windows boots. Now, after the blackout, the video card fan spins fast and wont stop. Nothing is displayed on the monitor. The monitor does not detect that the video card is sending it signals, it just stays on standby. No POST or beep codes. This is what I have tried so far: My motherboard has 2 PCI express slots and I tried plugging the video card into both of them but that didn't fix anything. I have replaced the power supply, that didn't fix anything. I cleared the CMOS, that didn't fix anything. Does anyone have any idea of what could be wrong? Thanks!

  Read the article

• Touchpad button assignments don't persist with Lenovo T400 on WinXP

  - by Nathan Fellman

  I have a Lenovo T400 notebook with Windows XP on it. I usually use the TrackPoint, and almost never use the TouchPad. I do a look of work on Linux over VNC, in my setup the middle mouse button is mapped to "paste". Considering that the notebook doesn't really have a middle button (it's only a scrolling button) I mapped the unused left button of the TouchPad to be a middle button. However, when I send the computer to Standby and bring it out, the left button reverts to being a left button, not a middle one. How can I make sure that the mapping persists?

  Read the article

• Internal LTO tape drive becomes hot

  - by claasz

  We use an internal LTO3 tape drive (HP Ultrium 920) in a PC (no particular server hardware) running Linux. The tape drive becomes quite hot - I don't have the exact temperature, but you may touch it for a second or two, then it hurts ;-) This happens when the tape has nothing to do (during reading/writing, it might become even hotter, I haven't checked that). Besides that, the system is working fine. Now I'm wondering Why does the tape becomes so hot? Is this something I need to care about? Is there something like a 'standby' mode for the tape? (I think it should not consume that much energy when it is not used)

  Read the article

• Linux WD30EZRX WD Green HDD & Blacx Duet 5G Usb

  - by Adam

  I have connected up an WD30EZRX WD Green HDD to a Thermaltake Blacx Duet 5G USB dock in Ubuntu 12.04. Every thing seems fine except when the HDD idles it seems to have error ls: reading directory .: Input/output error after a while and is only fixed by unmounting and remounting the drive as root. I have the following line in /etc/fstab UUID=AAF670E9F670B6E3 /media/3TB ntfs defaults,user,auto 0 0 I have noticed that it seems to go between /dev/sdc2 and /dev/sdd2 devices on remount. I did copy 1TB last night without issue in 1 sitting. But after x mins of idle it has remount issue. Any tips/suggestions on how to proceed would be appreciated. Spent most of the night googling and all its done is made me sad. Edit (tried as suggested): root@mediaserver:/media/3TB# sudo hdparm -B 255 -S 253 /dev/sdd2 /dev/sdd2: setting Advanced Power Management level to disabled HDIO_DRIVE_CMD failed: Input/output error setting standby to 253 (vendor-specific) APM_level = not supported Seems as if that didn't help with this particular drive.

  Read the article

• What is Mobsync.exe? Assuming I don't need it, can I disable it in Windows 7 without ill side effect

  - by Chris W. Rea

  I'm running Windows 7. Occasionally when I resume my computer from standby, it seems to wait 20-30 seconds or so before giving me full control back. In an attempt to diagnose why, I've been watching what's going on using the awesome Process Explorer. One of the processes I've noticed being started during that hiccup time is Mobsync.exe, described as "Microsoft Sync Center". Sync? Sync what? So, what is Mobsync.exe used for, exactly? Assuming I don't need its functionality, can I disable it in Windows 7 without ill side effect? If so, what's the best way to disable Mobsync.exe?

  Read the article

• what kind of memory can be categorized as Modified Memory in Resource Monitor

  - by Kavin

  In Windows 7 and Windows 2008 R2, there is a new Resource Monitor that is very useful and powerful to monitor the system. In the Memory section, I see a section called Modified (orange) The official description is: Memory whose contents must be to disk before it can be used for another purpose. But I am still confused. What kinds of memory is Modified? In which case can we say that this number of memory is Modified? Can anyone give me a specific example? Is the following guess correct? When a program want to write something into disk, it actually write the content to an IO buffer, which is in the memory. After OS flush this area of memory into disk, the memory is modified or standby?

  Read the article

• Dell U271 monitor DisplayPort suddenly not working

  - by Amir Latif

  My new(ish) Dell U271 took a bit of a knock and it now suddenly doesn't recognise the Macbook plugged into it via DisplayPort - this had been working great for several months up until now. When I "Scan Sources", it doesn't find anything on DisplayPort. However, one suspicious behaviour leads me to think all might not be lost. When the Mac is woken from sleep, this used to kick the monitor in (as an monitor would) and while it no longer does that, the light on the monitor does go from standby orange to blue briefly, then the monitor says it's going into "power save" mode. It seems like it gets some kinda signal. Any ideas on how I can diagnose the problem? I'm trying to find another mac but no one near me has one ...

  Read the article

• Install latest kernel to Ubuntu and have grub acknowledge the new installed kernel

  - by Phuong Nguyen

  I have an installed Ubuntu Distro (Karmic 9.10) already. However, due to some problems with xorg ati driver, I cannot standby my computer. Some guy have suggested me to try the latest version of xorg driver which in turn requires a newer version of Linux kernel than the newest release available from Ubuntu Central Repository (2.6.33). I have searched though several articles on how to install a custom Linux kernel. However, these articles are so 2004/2005 and they were talking about lilo (???). Since then, I'm afraid that I cannot make the Grub Boot recognize the new Linux kernel properly (I'm just a newbie to Linux). I would love to know how to install the kernel into Ubuntu and have grub acknowledge the new installed kernel.

  Read the article

• What settings to use for fastest reloading of a MySQL backup?

  - by Alex R

  I have a MySQL database which dumps to a 3.5 GB backup (mysqldump) in about 10 minutes. But reloading this backup on a standby / test server takes upwards of 12 hours. What are some settings that would maximize reloading performance? The most promising appear to be innodb_buffer_pool_size, innodb_additional_mem_pool_size, and innodb_log_buffer_size... but I'm reaching the limits of my trial-and-error approach. Which of these settings "should" be the most important? Through trial-and-error I was not able to get more than 70% CPU utilization and 63% memory utilization. I'd like both at 100% during a reload. All tables are InnoDB.

  Read the article

• EMC CX3-10c Fault Condition won;t clear

  - by ITGuy24

  We have an old CX3-10c from Dell that had both Standby Power Supplies (SPS) fail. This obviously caused a fault on the system and disabled the cache. We have replaced the SPS's and they test fine as do all other components. Problem is there is still a fault on the "Enclosure SPE [SPE3]" despite all the component in the enclosure showing as good. I was on the line with Dell Gold support for 3 hours yesterday, they have had me restart the SPs multiple times, as well as reseat the power supplies, even shutdown the system completely and power it back on. All to no avail. Fault remains and cache cannot be re-enabled so long as the Fault is present. Any suggestions on clearing this erroneous fault?

  Read the article

• Why is hibernation still used?

  - by Moses

  I've never quite understood the original purpose of the Hibernation power state in Windows. I understand how it works, what processes take place, and what happens when you boot back up from Hibernate, but I've never truly understood why it's used. With today's technology, most notably with SSDs, RAM and CPUs becoming faster and faster, a cold boot on a clean/efficient Windows installation can be pretty fast (for some people, mere seconds from pushing the power button). Standby is even faster, sometimes instantaneous. Even SATA drives from 5-6 years ago can accomplish these fast boot times. Hibernation seems pointless to me when modern technology is considered, but perhaps there are applications that I'm not considering. What was the original purpose behind hibernation, and why do people still use it? Edit: I rescind my comment about hibernation being obsolete, as it obviously has very practical applications to laptops and mobile PCs, considering the power restrictions. I was mostly referring to hibernation being used on a desktop.

  Read the article

• Media center consumes all available memory when attempting to play music off of a server

  - by RCIX

  I have Windows 7 Ultimate, and recently, when i try to play a song off of my Twonky Media Server/Windows Media Connect (based on an HP WHS with an Atom), it plays choppily. When i open Resource Monitor, it shows that after ordering the music to play, memory usage rapidly spikes to consume most, if not all, of the available memory on my system (excluding a couple hundred megabytes in standby). Why does it do this and is there anything i can do to stop it? Edit: it happens when I attempt to browse the server's music, not just when i play music. Edit 2: the "ehshell" process is what consumes the memory, appears to me something specific to media center. Moreover, the ehshell process doesn't die in this case. Edit 3: It only happens when browsing my Twonky library, and not my Windows Media Connect.

  Read the article

• Can I ping via an arbitrary interface of a DD-WRT system?

  - by bytebuster

  There's a Linksys WRT54GL router with DD-WRT firmware (v23SP2). The network has a simple dual-WAN configuration (standby mode, switching by a script): ~ # ip route 192.168.3.0/24 dev br0 proto kernel scope link src 192.168.3.1 192.168.2.0/24 dev vlan2 proto kernel scope link src 192.168.2.2 192.168.1.0/24 dev vlan1 proto kernel scope link src 192.168.1.67 127.0.0.0/8 dev lo scope link default via 192.168.2.1 dev vlan2 I'm trying to ping a certain server arbitrary via vlan1 or vlan2. What I tried, as suggested here: ping -I vlan2 <address> ping 192.168.2.1 <address> In both cases ping simply exits with no error messages. Also, ping ignores many other parameters, again, by exiting silently. I failed to find any references that DD-WRT has a limited version of ping whatsoever. I also don't think it can be a permissions issue as mentioned here since the only user with DD-WRT is root. What's wrong?

  Read the article

• ldirectord ipvsadm not show reals ip and not work wtih pacemaker and corosync

  - by miguer27

  first thanks for your time. I'm having a problem with ldirectord that I can not solve, I comment my situation: I have two nodes with pace maker and corosync and configure somes resources: root@ldap1:/home/mamartin# crm status Last updated: Tue Jun 3 12:58:30 2014 Last change: Tue Jun 3 12:23:47 2014 via cibadmin on ldap1 Stack: openais Current DC: ldap2 - partition with quorum Version: 1.1.7-ee0730e13d124c3d58f00016c3376a1de5323cff 2 Nodes configured, 2 expected votes 7 Resources configured. Online: [ ldap1 ldap2 ] Resource Group: IPV_LVS IPV_4 (ocf::heartbeat:IPaddr2): Started ldap1 IPV_6 (ocf::heartbeat:IPv6addr): Started ldap1 lvs (ocf::heartbeat:ldirectord): Started ldap1 Clone Set: clon_IPV_lo [IPV_lo] Started: [ ldap2 ] Stopped: [ IPV_lo:1 ] root@ldap1:/home/mamartin# crm configure show node ldap2 \ attributes standby="off" node ldap1 \ attributes standby="off" primitive IPV-lo_4 ocf:heartbeat:IPaddr \ params ip="192.168.1.10" cidr_netmask="32" nic="lo" \ op monitor interval="5s" primitive IPV-lo_6 ocf:heartbeat:IPv6addrLO \ params ipv6addr="[fc00:1::3]" cidr_netmask="64" \ op monitor interval="5s" primitive IPV_4 ocf:heartbeat:IPaddr2 \ params ip="192.168.1.10" nic="eth0" cidr_netmask="25" lvs_support="true" \ op monitor interval="5s" primitive IPV_6 ocf:heartbeat:IPv6addr \ params ipv6addr="[fc00:1::3]" nic="eth0" cidr_netmask="64" \ op monitor interval="5s" primitive lvs ocf:heartbeat:ldirectord \ params configfile="/etc/ldirectord.cf" \ op monitor interval="20" timeout="10" \ meta target-role="Started" group IPV_LVS IPV_4 IPV_6 lvs group IPV_lo IPV-lo_6 IPV-lo_4 clone clon_IPV_lo IPV_lo \ meta interleave="true" target-role="Started" location cli-prefer-IPV_LVS IPV_LVS \ rule $id="cli-prefer-rule-IPV_LVS" inf: #uname eq ldap1 colocation LVS_no_IPV_lo -inf: clon_IPV_lo IPV_LVS property $id="cib-bootstrap-options" \ dc-version="1.1.7-ee0730e13d124c3d58f00016c3376a1de5323cff" \ cluster-infrastructure="openais" \ expected-quorum-votes="2" \ no-quorum-policy="ignore" \ stonith-enabled="false" \ last-lrm-refresh="1401264327" rsc_defaults $id="rsc-options" \ resource-stickiness="1000" The problem is in the ipvsadm only show a one real IP, when i configured two now, show the ldirector.cf: root@ldap1:/home/mamartin# ipvsadm IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags - RemoteAddress:Port Forward Weight ActiveConn InActConn TCP ldap-maqueta.cica.es:ldap wrr - ldap2.cica.es:ldap Route 4 0 0 TCP [[fc00:1::3]]:ldap wrr - [[fc00:1::2]]:ldap Route 4 0 0 root@ldap1:/home/mamartin# cat /etc/ldirectord.cf checktimeout=10 checkinterval=2 autoreload=yes logfile="/var/log/ldirectord.log" quiescent=yes #ipv4 virtual=192.168.1.10:389 real=192.168.1.11:389 gate 4 real=192.168.1.12:389 gate 4 scheduler=wrr protocol=tcp checktype=on #ipv6 virtual6=[[fc00:1::3]]:389 real6=[[fc00:1::1]]:389 gate 4 real6=[[fc00:1::2]]:389 gate 4 scheduler=wrr protocol=tcp checkport=389 checktype=on and in the logs I see nothing clear: root@ldap1:/home/mamartin# ldirectord -d /etc/ldirectord.cf start DEBUG2: Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.11:389 -g -w 0) Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.11:389 -g -w 0) DEBUG2: Quiescent real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 0) Quiescent real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 0) DEBUG2: Disabled real server=on:tcp:192.168.1.11:389:::4:gate:\/: (virtual=tcp:192.168.1.10:389) DEBUG2: Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 0) Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 0) DEBUG2: Quiescent real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 0) Quiescent real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 0) DEBUG2: Disabled real server=on:tcp:192.168.1.12:389:::4:gate:\/: (virtual=tcp:192.168.1.10:389) DEBUG2: Checking on: Real servers are added without any checks DEBUG2: Resetting soft failure count: 192.168.1.12:389 (tcp:192.168.1.10:389) Resetting soft failure count: 192.168.1.12:389 (tcp:192.168.1.10:389) DEBUG2: Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 4) Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 4) Destination already exists root@ldap1:/home/mamartin# cat /var/log/ldirectord.log [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Quiescent real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 0) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Quiescent real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 0) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: 192.168.1.12:389 (tcp:192.168.1.10:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 4) failed: [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Added real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 4) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: 192.168.1.11:389 (tcp:192.168.1.10:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Restored real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 4) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: [[fc00:1::2]]:389 (tcp:[[fc00:1::3]]:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] system(/sbin/ipvsadm -a -t [[fc00:1::3]]:389 -r [[fc00:1::2]]:389 -g -w 4) failed: [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Added real server: [[fc00:1::2]]:389 ([[fc00:1::3]]:389) (Weight set to 4) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: [[fc00:1::1]]:389 (tcp:[[fc00:1::3]]:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Restored real server: [[fc00:1::1]]:389 ([[fc00:1::3]]:389) (Weight set to 4) do not know if this is a bug or a configuration error, can anyone help? Regards.

  Read the article

• Time Machine/iMac loses all trace of external hard drive after a few days

  - by Bill

  First time posting, also a Mac newbie (recent windows convert) so I'm hoping I can get some help here :) I have a Hitachi Deskstar drive in an external casing that I got from ebuyer. (its one of those unknown fairly cheapish enclosures) connected via firewire. I hook it up and it works fine, but then at some point over the next week or so I'll realise that my last update was 3 days ago or so. At this point the Mac will not recognise the drive as existing and the only thing to do is switch off and on the external enclosure. It then works fine for a while. If I had to guess I'm assuming its powering down or something when the Mac goes into standby? Is there anyway to solve this?

  Read the article

• Why can't I reconnect to my Philips SHB9000 bluetooth headset?

  - by Thomas Eyde

  When I connected my Philips SHB9000 bluetooth to my Windows 7 (64 bit) for the very first time, it worked well. I had to manually change the default playback device, but otherwise it worked. Then, when I start up my computer from standby, it's nearly random when I can reconnect or not. My last option is to remove the bluetooth device and reconnect it. But now, even that doesn't work. The sad thing is, this used to work better on Windows 7 beta. Windows Update has a new driver which fails to install. Searching for this driver yields nothing. I thought all vendors had an official site for their drivers? Well, Philips seems to have none. If there is no answer to this problem, my advice is to NOT buy this headset. It's good looking, the sound is nice, but what need do we have from that if we can't use the bloody device?

  Read the article

• Host hijacks USB printer from VirtualBox machine

  - by jackhab

  I have Ubuntu 9.1 running Windows XP in VirtualBox. Windows XP is a print server (there is no Linux driver for our printer). The printer is connected via USB and its USB filter is added to virtual machine settings. The problem is that every several hours Ubuntu tries to access the printer (trying to install it) and disconnects it from the virtual machine. The printer remains disconnected until I connect it again manually. I thought it is a problem with Windows power management but disabling sleep/standby in Windows didn't help. Please, advise.

  Read the article

• DVI to VGA adapter only working in one output

  - by Tom Jenkinson

  I have a AMD Radeon HD 6800 Series graphics card which has 2 DVI outputs. I tried to set it up with 2 monitors which both have vga connectors on the end and used 2 dvi to vga adapters like these. http://www.tvcables.co.uk/images/items/vga-to-dvi.jpg For some reason nothing would reach the monitor, it would remain in standby, if it was plugged into the second output. I tried all the different combinations of cables, adapters and the 2 monitors but whichever monitor that was plugged into the second output wouldn't work. I then randomly decided to plug a different monitor into the second output which has a dvi connector on the end so there was no need for an adapter and plugged it in and it worked! Does anyone know why the second output on the graphics card won't work with a dvi to vga adapter (and the first output will)? I'm really confused! Thanks

  Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14  | Next Page >