Search Results

Search found 439 results on 18 pages for 'thinkpad x200'.

Page 8/18 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >

• Wireless is detected, but not connecting. Ethernet works. How to correct the wireless address?

  - by Lucas

  I am running Ubuntu 14.04 with cable internet, and my wireless is detected and connected, but I cannot connect to the internet. I know the problem is with my machine because other machines are connecting to the same router just fine. I can connect via ethernet just fine as well. Here are some notable tests: ping 192.168.0.105 works with 0% packet loss, but ping 192.168.0.1 has 100% packet loss. When I plug in my ethernet, ping 192.168.0.1 works with 0% packet loss. My wireless name is tg, and the router ip is 192.168.0.1 (where I can enter username and password). I suspect that I need to change my wireless address from 192.168.0.105 to 192.168.0.1. Any suggestions on how to proceed? extra info: [lucas@lucas-ThinkPad-W520]/home/lucas$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"tg" Mode:Managed Frequency:2.462 GHz Access Point: 00:02:6F:83:F8:F4 Bit Rate=1 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:52 Invalid misc:166 Missed beacon:0 [lucas@lucas-ThinkPad-W520]/home/lucas$ ifconfig eth0 Link encap:Ethernet HWaddr f0:de:f1:b2:53:53 inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f2de:f1ff:feb2:5353/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:980003 errors:0 dropped:0 overruns:0 frame:0 TX packets:498384 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1320506168 (1.3 GB) TX bytes:59780591 (59.7 MB) Interrupt:20 Memory:f3a00000-f3a20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:21927 errors:0 dropped:0 overruns:0 frame:0 TX packets:21927 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1781719 (1.7 MB) TX bytes:1781719 (1.7 MB) wlan0 Link encap:Ethernet HWaddr 24:77:03:29:8f:dc inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2677:3ff:fe29:8fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11828 errors:0 dropped:0 overruns:0 frame:0 TX packets:15444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4855662 (4.8 MB) TX bytes:2250585 (2.2 MB) [lucas@lucas-ThinkPad-W520]/home/lucas$ lspci -nn | grep 0280 03:00.0 Network controller [0280]: Intel Corporation Centrino Ultimate-N 6300 [8086:4238] (rev 3e) [lucas@lucas-ThinkPad-W520]/home/lucas$ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no with ethernet unplugged: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 wlan0 with ethernet plugged in: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 [lucas@lucas-ThinkPad-W520]/home/lucas$ nm-tool NetworkManager Tool State: connected (global) - Device: wlan0 [tg] ---------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: no HW Address: 24:77:03:29:8F:DC Capabilities: Speed: 52 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) tatum: Infra, 40:8B:07:D8:A5:04, Freq 2437 MHz, Rate 54 Mb/s, Strength 42 W PA WPA2 ums: Infra, 00:20:A6:72:52:BF, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 Alpha 40: Infra, 28:CF:E9:86:59:5D, Freq 5260 MHz, Rate 54 Mb/s, Strength 30 W PA WPA2 thepromiselan: Infra, 58:6D:8F:51:E5:54, Freq 2452 MHz, Rate 54 Mb/s, Strength 34 $ PA WPA2 xfinitywifi: Infra, 06:1D:D5:84:27:A0, Freq 2437 MHz, Rate 54 Mb/s, Strength 52 *tg: Infra, 00:02:6F:83:F8:F4, Freq 2462 MHz, Rate 54 Mb/s, Strength 73 W PA2 ums: Infra, 00:20:A6:A1:9F:25, Freq 2452 MHz, Rate 54 Mb/s, Strength 44 BRIAN-PC_Network:Infra, 20:AA:4B:DD:93:D6, Freq 2462 MHz, Rate 54 Mb/s, Strength 35 W PA2 HOME-C0F8: Infra, 44:32:C8:D2:C0:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 40 W PA WPA2 abcsexy: Infra, 28:28:5D:27:5D:85, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 W PA WPA2 IPv4 Settings: Address: 192.168.0.105 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: e1000e State: connected Default: yes HW Address: F0:DE:F1:B2:53:53 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1

  Read the article

• How to restore infrared support in Windows XP?

  - by Emil Rasmussen

  My infrared port is not working on my Windows XP SP 3 (Thinkpad X60). I can see it Device Manager, and it's status is, that it is working probably. The problem manifests in several ways. Originally I was trying to transfer data from my Polar RS800CX watch, and the Polar ProTrainer 5 software gave me the this error message: "Communication port couldn't be opened". Then I tried to connect the watch to another computer, and the infrared connection was established immediately. I then tried to connect the other computer to my Thinkpad X60. The other computer again immediately showed the Wireless Link icon "'computername' is in range" in the notification area. But nothing is shown on the Thinkpad, and a file transfer to the Thinkpad is unsuccessful with an error message that reports that "the target machine actively refused it [the connection]". This brings me to conclude that the infrared support in Windows on the Thinkpad is somehow broken. This is further supported by the fact that I can't find the "Wireless Link" icon in the Control Panel and when I try to run the irprops.cpl nothing happens. So the question is, how to reinstall the infrared support? Some of the solutions that I have explored is: I have tried to disable/enable the infrared in the BIOS - to trick a re-installation. The IR modules settings on the other computer that can get a successful IR connection is an exact match to the ThinkPad that can't get a connection. The was a problem in Windows XP SP 2 with the Wireless Link icon - MS KB article - but that hotfix can't be applied on SP 3 installation. I also guess that the hotfix is included in SP 3. Any other suggestions?

  Read the article

• How to get used of trackpoint on a thinkpad?

  - by AZ

  Recently my shoulder hurts due to frequently arm movement switching between keyboard and mouse. Then I start using trackpoint. The problem is, while everyone saying the trackpoint is more accurate than touchpad, I find it very hard to accurately move the cursor using trackpoint. Large movements are ok, but when it comes to fine movements, such as click a close button or check a checkbox, it takes longer time. Should I just practice more, or are there any good tips or tutorials around?

  Read the article

• IBM Thinkpad 240 - Best way to boot from floppy to USB - Best Linux for 300 MHz 128 MB RAM 800x600 s

  - by zillion

  Mostly I still have that old 'ultraportable' laptop that is mostly like a pre-netbook era laptop and a friend and programmer needs a computer because the one he was using just broke and he has to wait until the new one arrive in 4-6 weeks ... This laptop has no LAN connection and CD-ROM so be prepared for a real challenge! All hardware is well supported on Windows XP (included drivers on the Windows XP CD) and on Linux out-of-the-box (but the screen need a special configuration.) Mostly any Linux that will work well with Skype (USB or regular headset), any MSN client and a text writer for code will do. What I have tested so far: Slitaz 2 don't boot because the floppy of GRUB4DOS don't see the USB drive (fully working and tested on my regular laptop), Damn Small Linux was working but was needing a special screen configuration that I don't remember (in the boot options of the floppy) and now I'm thinking about Puppy Linux that is seen to work totally out of the box with it but I will need an old Puppy version (1 or 2 I think) and the Wakepup floppy ... If you got some ideas to help or to try I'm open!

  Read the article

• Possible to remap the Fn+C/V to Ctrl+C/V key combinations on a Thinkpad?

  - by yegor

  I know remapping the Fn key alone seems like its impossible, but what about the actual combination? FN + c, FN + V and FN + a to be remapped to the ctrl + C, V, A. Doable?

  Read the article

• T400: How do you disable the green brightness meter on a Thinkpad T400?

  - by vilmosz

  I find the green brightness meter that pops up when I am on battery to be annoying. Is there a setting where I can disable this?

  Read the article

• Live CD / Live USB much faster than full install

  - by user29347

  I've observed it on both laptops I own! HP Compaq nx6125 and Ubuntu 11.04 x64 - somewhat solved Lenovo Thinkpad T500 and Ubuntu 11.10 x64 - help needed! I'm still struggling with the Thinkpad to get performance level similar to that of 10 y.o. laptops... All in all a really serious issue with multiple versions of Ubuntu that renders computers with perfectly compatible hardware unusable, as far as out of the box experience is concerned. Troubleshooting resultant issues seems to be a hard case even for users with some experience with installing graphics drivers. EDIT: I can't really post additional details. Two different ubuntu versions, two laptops, two different set of graph. drivers (OS vs ATI prop.) - all with the same symptoms. Also I can't stress enough how massive the performance degradation is compared to a healthy system. For that reason I ask for input from people who may know roughly what are we dealing with here. I can post more details if we were to focus on my current Thinkpad T500. In that case my current system details: Lenovo Thinkpad T500 Ubuntu 11.10 x64 ATI Mobility Radeon HD 3650 (also see the "What I have already tried" section about Intel graphics tested) ATI Catalyst 11.10 drivers OCZ Agility 3 SSD but! same with the default driver for ATI the card same with the prop. driver for the ATI card from Jockey (Additional drivers applet) What I have already tried: 0. Switching to Intel integrated card (Intel GMA 4500M HD) with the default driver - same effects = may indicate not driver related problem but a problem with something of global influence like e.g. nomodeset or other I don't even know about. (What you can read above) ATI Catalyst 11.10 and radeon.modeset=0 boot parameter + disabled Wait for VBlank. Unity 2D Ubuntu 10.04 LTS tested (ubuntu-10.04.3-desktop-i386.iso): Both live USB and installed version blazing fast! (on the default drivers - without even installing the proprietary fglrx drivers). re2 a) seems to give me the only significant results (still poor) - perfect Unity elements performance with the same crawling stuttering/lagging when dragging windows around. re2 b) this happens often http://i17.photobucket.com/albums/b68/Bucic/ubuntuforumsorg/Screenshotat2011-10-28083140.png re2 c) Sometimes I am able to witness a normal performance when dragging a window around but only for a second or two. When I try to shake it longer it starts to lag and it will keep lagging like that with an increased probability of what you see in the sshot in point re2 b). re2 d) I can't establish the radeon.modeset=0 influence though. Once it seems to work be smooth with it, the other time - without it. Really can't tell.

  Read the article

• How to setup a wired local area network in Windows 7?

  - by user883434

  I am using a Lenovo ThinkPad X200 and want to se tup a wired local area network. How could I achieve this? Actually, my question is very simple. I just want to connect to the internet and I have a cable connection at home. So, I just want to plug the cable line to my notebook (x200) so that I can access the internet via the cable. But I dont know how to setup a local area connection in notebook. Since it automatically appear in my desktop, but not in my notebook. Thanks!

  Read the article

• T60 Screen/LCD gets black after some minutes with a highpitched sound rising and fading

  - by Edward De Leau

  Just now my T60 screen got "black" (so no display). On my second monitor: no problems so the vga output works. symptom: Screen blanks / no display but works on second monitor steps to reproduce: - boot - wait (it does not matter what you do you do not have to login or anything) - (now the monitor of the laptop slowly begins to make a ssssssssHHHHHHHHHHHHHHHHHWOEOEssssssss noice of about 10 seconds) - right after the sounds ends the monitor gets black times seem to be the same each time. software: installed no new software before/after, running zone alarm and antivirus. other: it does not feel hot in any place, there dont seem to be running processes with strange behaviour. warranty: out of warranty what was i doing: typing text on a website and doing some php coding in a text editor. Anyone any idea what I can do here other than buy a new laptop? / does it sound familiar to known cases? update: * exactly the same problem: http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-Screen-Blackout/m-p/288772 and the second poster (garyj) here: http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/Black-Screen-on-T60/m-p/235053#M48627 and here: "i have that same problem. i replaced the CCRL on mine and it works fine when the screen is not screwed in. once the frame of the LCD screen (metal portion) touches the metal on the laptop which holds the screen the screen goes black. If the metal is touching the screen when you boot up it boots up with it being very dimmly lit. " from http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-screen-problems/m-p/205047#M44995 (it seems replacing the lcd is no use, he tried it 3 times). same problem: http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-black-screen/m-p/80604#M25914 Hmmm... not handy 3 or 4 months ago I ordered and installed a new fan. Now the LCD. Which does not seem the core isse but some electric issue so it seems replacing the LCD is not the thing todo here. I have the following question: If it is not the LCD that needs to be replaced (see other threads) which parts can I order to fix this? Has anyone got any information which could lead me to identify the issue? I have read replacing the "inverter" AND the "backlightning" would that make sense?

  Read the article

• How do you disable the back button on a lenovo T60?

  - by bobobobo

  There is an awful stupid button on this lenovo T60 i'm using which sends the browser back a page. I really need to disable it. I can't find it anywhere in the Keyboard settings in control panel or the special Lenovo setup utility ("Thinkpad configuration"). Thinkpad Config has everything but keyboard. Its got mouse, trackpoint..

  Read the article

• Windows 7 laptop with problems shutting down

  - by Seth Sticco

  This is a thinkpad convertible tablet with Windows 7. When you try to shut down, it seizes at a screen with a gradient background and a Think/Thinkpad logo (forgot which). If you close it at that point, wait for the moon led to light up (meaning it's sleeping), then open it back up, it immediately continues and shuts down successfully. Any ideas on how to troubleshoot this?

  Read the article

• Would it be possible to swap system restore points on different brands of computers?

  - by P'sao

  So I have a ThinkPad computer that I've installed a program called "Deep Freeze" which restores your computer to the "Frozen" state. I also have a Toshiba computer with no Deep Freeze on it. My question is that would it be possible to creat a system restore point on my Toshiba and then replace the system volume information folder with the one on the ThinkPad so I could restore to a point with no Deep Freeze? Would this work?

  Read the article

• 64-bit 13.10 shows 1GB less RAM than 64-bit 13.04 did

  - by kiloseven

  Multiple 64-bit versions (Kubuntu, Lubuntu and Xubuntu) once installed on my ThinkPad R60 show 3GB of RAM, not the correct 4GB of RAM. Last week with 13.04, I had 4GB of RAM (which matches the BIOS) and this week I have 3GB available. Inquiring minds want to know. Details follow: Linux R60 3.11.0-12-generic #19-Ubuntu SMP Wed Oct 9 16:20:46 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux r60 free -m reports: _ total used free shared buffers cached Mem: 3001 854 2146 0 22 486 -/+ buffers/cache: 346 2655 Swap: 0 0 0 . . . . . . lshw shows: description: Notebook product: 9459AT8 () vendor: LENOVO version: ThinkPad R60/R60i serial: redacted width: 64 bits capabilities: smbios-2.4 dmi-2.4 vsyscall32 configuration: administrator_password=disabled boot=normal chassis=notebook family=ThinkPad R60/R60i frontpanel_password=unknown keyboard_password=disabled power-on_password=disabled uuid=126E4001-48CA-11CB-9D53-B982AE0D1ABB *-core description: Motherboard product: 9459AT8 vendor: LENOVO physical id: 0 version: Not Available *-firmware description: BIOS vendor: LENOVO physical id: 0 version: 7CETC1WW (2.11 ) date: 01/09/2007 size: 144KiB capacity: 1984KiB capabilities: pci pcmcia pnp upgrade shadowing escd cdboot bootselect socketedrom edd acpi usb biosbootspecification {snip} *-memory description: System Memory physical id: 29 slot: System board or motherboard size: 4GiB *-bank:0 description: SODIMM DDR2 Synchronous physical id: 0 slot: DIMM 1 size: 2GiB width: 64 bits *-bank:1 description: SODIMM DDR2 Synchronous physical id: 1 slot: DIMM 2 size: 2GiB width: 64 bits dpkg -l linux-* returns: Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Conf-files/Unpacked/halF-conf/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad) ||/ Name Version Description +++-======================================-=======================================-========================================================================== un linux-doc-3.2.0 (no description available) ii linux-firmware 1.79.6 Firmware for Linux kernel drivers ii linux-generic 3.2.0.52.62 Complete Generic Linux kernel un linux-headers (no description available) un linux-headers-3 (no description available) un linux-headers-3.0 (no description available) un linux-headers-3.2.0-23 (no description available) un linux-headers-3.2.0-23-generic (no description available) ii linux-headers-3.2.0-52 3.2.0-52.78 Header files related to Linux kernel version 3.2.0 ii linux-headers-3.2.0-52-generic 3.2.0-52.78 Linux kernel headers for version 3.2.0 on 64 bit x86 SMP ii linux-headers-generic 3.2.0.52.62 Generic Linux kernel headers un linux-image (no description available) un linux-image-3.0 (no description available) ii linux-image-3.2.0-52-generic 3.2.0-52.78 Linux kernel image for version 3.2.0 on 64 bit x86 SMP ii linux-image-generic 3.2.0.52.62 Generic Linux kernel image un linux-initramfs-tool (no description available) un linux-kernel-headers (no description available) un linux-kernel-log-daemon (no description available) ii linux-libc-dev 3.2.0-52.78 Linux Kernel Headers for development un linux-restricted-common (no description available) ii linux-sound-base 1.0.25+dfsg-0ubuntu1.1 base package for ALSA and OSS sound systems un linux-source-3.2.0 (no description available) un linux-tools (no description available)

  Read the article

• Supertuxkart not able to start

  - by subeh.sharma

  Was working fine before i played around with NVIDIA drivers and ended up with this problem. I tried running it through the terminal and i see these messages: subsharm@subsharm-ThinkPad-T61:~$ supertuxkart Irrlicht Engine version 1.7.2 Linux 3.0.0-15-generic #25-Ubuntu SMP Mon Jan 2 17:44:42 UTC 2012 x86_64 [FileManager] Data files will be fetched from: '/usr/share/games/supertuxkart/' [IrrDriver] Creating NULL device Irrlicht Engine version 1.7.2 Linux 3.0.0-15-generic #25-Ubuntu SMP Mon Jan 2 17:44:42 UTC 2012 x86_64 [IrrDriver] Trying OpenGL rendering. [IrrDriver] Tring to create device with 32 bits Xlib: extension "GLX" missing on display ":0.0". [IrrDriver Temp Logger] Level 1: No GLX support available. OpenGL driver will not work. [IrrDriver Temp Logger] Level 2: Fatal error, could not get visual. Segmentation fault subsharm@subsharm-ThinkPad-T61:~$ sudo Xorg -configure [sudo] password for subsharm: Fatal server error: Server is already active for display 0 If this server is no longer running, remove /tmp/.X0-lock and start again.

  Read the article

• How do I turn off WLAN automatically when LAN is connected?

  - by derroman

  I use my Thinkpad laptop with a docking station. The docking station is connected to my router via LAN. When I walk around the house I use my laptop with WLAN. Is it possible (and how) to manage these devices with a script or something to work like this: If a LAN-Connection is up, the OS should turn off Wifi and if LAN-Connection gets lost (undocking) Wifi should turn on automatically. I use Ubuntu 11.04 64bit with Gnome 2. The system works on an Lenovo ThinkPad R500 with. WLAN-Device: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] LAN-Device: Broadcom Corporation NetLink BCM5787M Gigabit Ethernet PCI Express (rev 02) Any help would be appreciated. Thanks.

  Read the article

• Laptop GPU apparently blew up, motherboard doesn't even turn on its power LED. [But..]

  - by leladax

  EDIT: (Was: Laptop automatic shutdown after 2 seconds) If I take out the GPU, the motherboard LED turns on but then [if it attempts to power up and boot] it turns off after 2 seconds [fans turn on normally in that short period]. [Without the GPUs out there's not even an attempt to boot.] It's an SLI motherboard for a toshiba (model X200-219). If I take out one of the GPUs (they are on top of each other) it surprisingly lets the motherboard turn on too (as it is if both are out) but it still turns off after 2-3 seconds, same behavior. I wonder if it's the GPU that produces the 'turn off after being on' behavior and not something else. [Has anyone seen this behavior with blown up GPUs or could it be something else?] Previous question (before EDIT. Sorry, but someone thought it productive to lock the other one as duplicate): I'm trying to insvestigate which component produces this behavior. Other indications show it may be the GPU but I wonder if anyone knows more. It's a Toshiba Satellite X200 description: AC power shows the power being fed normally, when turned on the fan works and it appears to be starting up but after 2 seconds it shuts down with only the 'AC power connected" led on. -- seconds are about up to 4,maybe not 2 exactly.

  Read the article

• Recommendations on laptops - long battery life, slim, Windows 7

  - by molecule

  Hi, I have been looking at a couple of laptops... The most important requirement is long battery life, slim & light, and runs Windows 7. One that seems to fit the bill is the Sony Vaio Z series laptops. They claim to have long battery life, have some really impressive specs (on paper) and a very nice design. They are not on sale where I am yet but has seen/used them? Second would be the Lenovo Thinkpad IBM x301 For business users, Thinkpad seems to be the way to go. I have also considered Dell Alienware M11x but may not be completely appropriate for business use? What would you recommend with a budget of USD1500-2000?

  Read the article

• Monitor-Specific Color Profile Results In Yellow Grayscale Images

  - by Zian Choy

  I recently purchased a new Acer S201hl monitor. Many lay reviews compliment its color accuracy with people noting only a bit of a blueish tinge. After a little time, Windows found, and I installed, the Acer drivers via Microsoft Update. During the installation process, the software installed an ICC profile for the monitor from Acer. I recently noticed that when I view photos using Windows Live Photo Gallery, the colors are wrong. For example, grayscale document scans appear with yellow backgrounds instead of white backgrounds. This happens with both my external monitors and my ThinkPad's built-in screen. When I removed the monitor-specific profile from the list of profiles associated with a monitor (for example, removing the Acer profile from the Acer monitor), the problem went away for that screen. I checked with Microsoft KB939395 and though it says "an incorrect color profile [...] is used for the monitor," the profile associated with my ThinkPad's screen seemed to be correct, based on its name.

  Read the article

• Why ping another innet machine from MacBook get netgate's ip address?

  - by Xinwang

  I have three machine in my home network connected by a wireless router. One is server installed linux at 192.168.1.1, another is Thinkpad with MS Windows XP at 192.168.1.2, last one is MacBook Pro with Mac OS X 10.6.3 at 192.168.1.3. When I ping the Linux Server from Thinkpad (MS Windows XP) I can get the correct ip address, but when I ping it from Mac I get the global address of my router, like 61.135.181.175. Could you tell me why this happen? And how do I get same ping result on Mac and Windows. Thanks

  Read the article

• Taking over and Moving a PHP site

  - by KCavon

  I have a internal use PHP site at my new position. It only runs a few days a year off site so we keep it on laptops. The hardware it has been on, a 8 year IBM Thinkpad running Fedora, is dying. I have new Lenovo Thinkpad's running latest and greatest Ubuntu. I have copied the contents of var to a shared drive, renamed the old www folder in var on the new machine and copied over the old www folder. I can get to the login page and into the site, but when I look something up it returns Cannot Open. I know I cannot get to the MySQL in the new machine because users and passwords dont match. The version of the PHP from the old machine is before the setup script was included. I know very little about PHP. I am looking for input on the proper way to link the old PHP files to my mysql instance. Any help, much appreciated.

  Read the article

• Why ping another inet machine from MacBook get netgate's ip address?

  - by Xinwang

  I have three machine in my home network connected by a wireless router. One is server installed linux at 192.168.1.1, another is Thinkpad with MS Windows XP at 192.168.1.2, last one is MacBook Pro with Mac OS X 10.6.3 at 192.168.1.3. When I ping the Linux Server from Thinkpad (MS Windows XP) I can get the correct ip address, but when I ping it from Mac I get the global address of my router, like 61.135.181.175. Could you tell me why this happen? And how do I get same ping result on Mac and Windows. Thanks

  Read the article

• T60 Screen/LCD gets black after some minutes with a highpitched sound rising and fading

  - by edelwater

  Just now my T60 screen got "black" (so no display). On my second monitor: no problems so the VGA output works. Symptom: Screen blanks / no display, but it works on the second monitor Steps to reproduce: - boot - wait (it does not matter what you do you do not have to login or anything) - (now the monitor of the laptop slowly begins to make a ssssssssHHHHHHHHHHHHHHHHHWOEOEssssssss noise of about 10 seconds) - right after the sounds ends, the monitor gets black. Sometimes it seems to be the same each time. Software: Installed no new software before/after, running ZoneAlarm and antivirus. Other: It does not feel hot in any place, there don't seem to be running processes with strange behaviour. Warranty: Out of warranty What was I doing: Typing text on a website and doing some PHP coding in a text editor. What can I do here other than buy a new laptop? Does it sound familiar to known cases? Update 1: Exactly the same problem: http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-Screen-Blackout/m-p/288772 and the second poster (garyj), http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/Black-Screen-on-T60/m-p/235053#M48627 And here: "I have that same problem. I replaced the CCRL on mine and it works fine when the screen is not screwed in. Once the frame of the LCD screen (metal portion) touches the metal on the laptop which holds the screen the screen goes black. If the metal is touching the screen when you boot up it boots up with it being very dimmly lit. " from http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-screen-problems/m-p/205047#M44995 (it seems replacing the LCD display is no use, he tried it three times). Same problem: http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-black-screen/m-p/80604#M25914 Hmmm... not handy 3 or 4 months ago I ordered and installed a new fan. Now the LCD. Which does not seem the core issue but some electric issue so it seems replacing the LCD is not the thing to do here. If it is not the LCD that needs to be replaced (see other threads), which parts can I order to fix this? Is there any information which could lead me to identify the issue? I have read replacing the "inverter" AND the "backlightning" would that make sense? Update 2: I replaced the inverter with another inverter, but IO have the same problem. I DID notice that the inverter is the component that makes the sssssssssssssHHHHHHHHHH sound AND it becomes very hot in a few seconds. (So both the old and the test one) The problem is hmmm wat is then the thing that makes the inverter hot by (assumption) after which it shuts itself down. Is it either the input or the output? The output seems to me not, because the screen seems to function so it must be the electricity coming in. But what causes it to become so hot would it be the VGA card outputting some unusual high voltage seems unlikely? I am looking for the component to order / replace update 3: Great news. Ewendish gave me the hint to look in the BIOS. While I was in the BIOS I noticed that the screen did not switch off and there was not a high pitched sound. So I lowered some settings in the BIOS. I then noticed that with brightness turned to 0 (via FN End), it does not make a high pitched sound and does not turn off, with brightness turned up just three "stripes" it starts making the sound. So I could from now on work under lowest brightness modus or... see where the problem lies. So as stated below with either power management or display drivers / ATI Catalyst settings / Windows display settings. I'm trying to see where it lies, but I will google some first. Update 4: I wiped clean the Windows XP installation and installed Windows 7 on it. Unfortunately the problem remains: as soon as the brightness goes up the screen starts hissing. This means... back to original thought: it probably IS a hardware problem. Although ... again... if it is NOT the inverter, what is it? Could it be the backlightning component? I could try to switch that with a another T60... but this is quite tricky.

  Read the article

• Can DVI look different?

  - by queueoverflow

  I have a desktop with an nVidia GT 9500 which has two DVI slots. I have a 24" TN-Panel TFT on that and it looks pretty good. Then I hooked it onto the DisplayPort of my ThinkPad with the Intel HD 3000 card with an DP-DVI adapter and I think that the fonts look even clearer. Both computers run Kubuntu 12.04, although the ThinkPad is freshly set up, while the desktop is migrated from the previous release. Is this a hardware thing or is it just some setting in the anti-aliasing or sub-pixel-hinting?

  Read the article

• Wireless option grayed out in Windows Mobility Center

  - by thomasvdb

  We currently have a Lenovo ThinkPad L512 which can't connect to wireless networks. He simply indicates he can't find any networks. Other notebooks (also ThinkPad L512-notebooks) in the company do find the network so nothings wrong with the configuration of the wireless router. As indicated on answer.microsoft.com, I should check Windows Mobility Center and enable the entry "Turn Wireless On". Unfortunately this option has been grayed out. How can I enable this option? There isn't a physical switch on the laptop to turn on the wireless.

  Read the article

• Error when I try to installth desktop integration features for Openoffice

  - by PENG TENG

  peng@peng-ThinkPad-SL410:~$ cd '/home/peng/Downloads/en-US/DEBS/desktop-integration' peng@peng-ThinkPad-SL410:~/Downloads/en-US/DEBS/desktop-integration$ sudo dpkg -i *.deb (Reading database ... 357248 files and directories currently installed.) Unpacking openoffice.org-debian-menus (from openoffice.org3.4-debian-menus_3.4-9593_all.deb) ... dpkg: error processing openoffice.org3.4-debian-menus_3.4-9593_all.deb (--install): trying to overwrite '/usr/bin/soffice', which is also in package libreoffice-common 1:3.6.2~rc2-0ubuntu3 /usr/bin/gtk-update-icon-cache gtk-update-icon-cache: Cache file created successfully. /usr/bin/gtk-update-icon-cache gtk-update-icon-cache: Cache file created successfully. Processing triggers for menu ... Processing triggers for hicolor-icon-theme ... Processing triggers for gnome-icon-theme ... Processing triggers for shared-mime-info ... Unknown media type in type 'all/all' Unknown media type in type 'all/allfiles' Unknown media type in type 'uri/mms' Unknown media type in type 'uri/mmst' Unknown media type in type 'uri/mmsu' Unknown media type in type 'uri/pnm' Unknown media type in type 'uri/rtspt' Unknown media type in type 'uri/rtspu' Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for desktop-file-utils ... Processing triggers for gnome-menus ... Errors were encountered while processing: openoffice.org3.4-debian-menus_3.4-9593_all.deb Can anyone solve the problem?

  Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >