Search Results

Search found 11003 results on 441 pages for 'usb storage'.

Page 8/441 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >

  • Laptop stopped recognizing USB hard drive

    - by vahokif
    Hi, My Packard Bell EasyNote TX86 laptop stopped recognizing my 1 TB Toshiba Store Art hard drive. It worked fine until now, and it still works on other computers. Other USB devices (including storage) work, and I've tried plugging it in every port, to no avail. When I plug it in it spins up, but Windows doesn't react at all (it's not in disk management), Linux doesn't write anything in dmesg and I can't see it in BIOS setup. I didn't use it at all today, apart from plugging it into a freshly-installed Windows 7 machine once (where it worked). What can I do? Which device is to blame here? EDIT: One more thing. I unplugged the drive while the laptop was hibernated. Google says this might be the problem and it might have something to do with resetting the USB Host Controller.

    Read the article

  • Can't mount Linux usb disk. It just create /dev/sg device but no /dev/sd

    - by MTilsted
    I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata). Added: I did try to mount /dev/sg3 but mount say that its not a block device. (File say Its a character special device). Added output from dmesg: [ 97.454073] usb 7-1: USB disconnect, address 2 [ 105.913055] hub 2-0:1.0: unable to enumerate USB device on port 3 [ 107.048054] usb 2-3: new high speed USB device using ehci_hcd and address 5 [ 107.162900] usb 2-3: New USB device found, idVendor=1b1c, idProduct=1ab8 [ 107.162903] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=5 [ 107.162906] usb 2-3: Product: CSSD-R60GB2 [ 107.162908] usb 2-3: Manufacturer: Corsair [ 107.162910] usb 2-3: SerialNumber: 10111441000000990069 [ 107.167651] scsi7 : usb-storage 2-3:1.0 [ 108.195543] scsi 7:0:0:0: Direct-Access Corsair CSSD-R60GB2 PQ: 1 ANSI: 0 [ 108.197732] scsi 7:0:0:0: Attached scsi generic sg3 type 0

    Read the article

  • Alfa AWUS036H USB wireless adapter not recognized

    - by GFiasco
    The Alfa AWUS036H USB wireless adapter will not be recognized by my netbook (Ubuntu 14.04, Asus X201E). As I understand it, the drivers should already be built in to this version of Linux, but I tried a make/make install of the latest Realtek drivers (as mentioned on How do I install drivers for the Alfa AWUS036H USB wireless adapter?) and it didn't work. I then followed the advice of this thread (ALFA AWUS036NH driver) and did a make/make install of the most up-to-date backport of the drivers, but that didn't work. At this point I tried a series of commands from this thread (http://ubuntuforums.org/showthread.php?t=2187780) in an attempt to identify the problem, but at no point could I get the laptop to ever recognize the USB adapter. I have also troubleshot the USB cable itself, tried both the USB 2.0 and 3.0 ports on the laptop, have never received an error message regarding a need to update the firmware, and have seemingly successfully installed all manner of variation of Realtek drivers which were supposed to make the adapter work. (I also tried to delete/clean up after each install, in the hope I wasn't making things worse.) Not sure what I should do next. Please let me know if I need to post any more information. Thanks very much for your help. EDIT: Before inserting Alpha USB adapter: :~$ lsusb Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:570c Realtek Semiconductor Corp. Bus 001 Device 026: ID 13d3:3393 IMC Networks Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 002: ID 03f0:3112 Hewlett-Packard Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub After inserting Alpha USB adapter (USB 3.0 port, no change): :~$ lsusb Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:570c Realtek Semiconductor Corp. Bus 001 Device 026: ID 13d3:3393 IMC Networks Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 002: ID 03f0:3112 Hewlett-Packard Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Ran tail -f /var/log/syslog, inserted device, no recognition (last entry is dated 16:17:01, so an hour ago). Going to check on an Ubuntu 14.04 laptop and Windows XP desktop. I'll update after. Thanks for your help to this point.

    Read the article

  • Can't install alternate CD from USB?

    - by mattias
    Hi im trying to install ubuntu 12.04 with full hard disk encryption. After downloading and installing the Ubuntu live CD, I learned that truecrypt doesnt support full disk encryption on linux. I also learned that the best way to get "nearly full disk encryption" on ubuntu is by installing it from the alternate install CD. I tried that, but something is wrong with my CD reader/burner so it doesnt boot up when i insert the cd. My thought here was to take the .iso that I downloaded on my unencrypted Ubuntu system, use Unetbootin to make the usb drive. The usb drive used for this is exactly the same brand as one that I know has worked with a previous ubuntu live system on the same computer. I also used unetbootin for that usb, but I created it from windows that time. The usb stick boots up fine and i get through the first couple of steps in the installation process. However, After a while I get a "box" with the following error message "Load Installer components from CD" There was a problem reading data from the CD-ROM. Please make sure it is in the drive. If retrying does not work, you should check the integrity of your CD-ROM. "Failed to copy file from CD-ROM. Retry? " Then I cant get any further. I googled a lot and found this page which seems to tackle this very problem: http://www.dotkam.com/2010/11/29/ins...mage-from-usb/ I tried to do what it said. After pressing TAB, I wrote : cdrom-detect/try-usb=true without quotes because that's what i think is right. When I press TAB, there already is a text saying : /ubnkern initrd=/ubninit vga=788 -- quiet which can be removed. I have tried to both delete the text before the "--" and just inserting cdrom-detect/try-usb=true before it. Any idea of what can be wrong? I would like to do a full system encryption, or as full as it is possible. I dont want to just encrypt my /home folder. Maybe this isn't the easiest way. I use SanDisk usb sticks. I know there is a problem with U3 launcher on some SanDisks, but I never had to remove U3 before from similar disks, and the alternate install does boot up, so I dont think using U3 removal would help me. Any help or indication to an easier way to do this would be appreciated

    Read the article

  • Save and Run Programs From USB

    - by UbuntuRob
    At the moment I am running Ubuntu 12.10 from a USB memory stick, and I wondered whether it would be possible to save and run any programs I have downloaded from another USB stick instead of the one with the operating system on. I'd like to be able to set the download location in Ubuntu Software Center to the second memory drive, but i don't know how to do this. I can keep the operating system on the one USB and the programs on the other USB, which makes everything much more easier. Any ideas?

    Read the article

  • Online Storage and security concerns

    - by Megge
    I plan to set up a small fileserver. I already own a small server at HostEurope (VirtualServer L, 250GB space), but they don't offer enough space (there is the HostEurope Cloud, but paying for bandwidth isn't an option here, video-streaming should be possible) Requirements summarized: Storage: 2TB, Users: ~15, Filesizes: < 100GB, should be easily reachable (Mount as a networkdrive or at least have solid "communication" software) My first question would be: Where can I get halfway affordable online storages? And how should I connect them to my server? Getting an additional server is a bit overkill, as I know no hoster which allows 2 TB on a small 2 Ghz Dual Core 2 GB RAM thingy (that would be enough by far, I just need much space), and connecting it via NFS or FTP over Internet seems a bit strange and cripples performance. Do you have any advice where I could get that storage service from? (I sent HostEurope a custom request today, but they didn't answer till now. If they can provide me with that space, this question will be irrelevant, but the 2nd one is the more important one anway, don't do much more than recommend me some based on experience, you don't have to crawl hours through hosting services) livedrive for example offers 5 TB for 17€ / month, I'd be happy with 2 TB for 20 €, the caveat is: It doesn't allow multiple users, which leads me to my second question: Where are the security problems? Which protocol is sufficient (I want private and "public" folders etc. the usual "every user has its own and a public space"-thing), secure and fast? (I'd tend to (S)FTP, problem with FTP is: Most of those hosting services don't even allow FTP with mutliple users and single users lead me into "hacking" a solution (you could map the basic folder structure on the main server and just mount every subfolder from the storage, things get difficult with a public folder with 644 permissions though) Is useing something like PKI or 802.1X overkill for private uses?

    Read the article

  • Cannot re-install Ubuntu 12.04 via USB (USB booting issue)

    - by Mohd Arafat Hossain
    I've read the previous questions related to my same problem regarding the USB not booting issue and have tried everything from what was replied in those post's but still no luck. I will tell you everything I have done so far (If it helps in any way...) 1) Previously I had Windows 7 running on my laptop, where I downloaded the official torrent ISO (i386 desktop) and using Unetbootin I made a bootable USB 2) Restarted the laptop with the USB connected and IT BOOTED, then I installed it on my HDD(Internal) replacing my Windows 7 3) After installing it restarted and I took some time to explore Ubuntu after the log in, then went online and followed some website for the things to do after installing Ubuntu 12.04.....and then there were errors while installing some softwares and plug-ins. The error asked me to check if i was connected to the Internet properly....while I was surfing facebook good as always on an open Firefox. The same error comes when installing Ubuntu one. 4) so I decided to re-install Ubuntu thinking I had done something wrong during the installation (I'm installing from the same USB)...and it didn't boot. I checked the boot priority and it was/is set in USB first (as always). To say in detail what happens is when I restart the USB light flashes at start, later on stops and in the screen the installed Ubuntu 12.04 loads up for me to log in (meaning it's not booting from the USB). By reading you can see that I haven't done much and I honestly didn't even touch the system settings to mess things up. As I have mentioned above I've tried everything in the previous post's in this related topic and it didn't work so I'm hoping for a new solution as a reply. Thanks in advance :) Edited: I wanted to add this I want to clean install instead of solving errors so please give a step by step guide. thanks for any help :)

    Read the article

  • Enterprise Manager 12c ? ZFS Storage Appliance

    - by user13138569
    ?????????????? Enterprise Manager 12c ??? Sun ZFS Storage Appliance ????????????????????? ???Enterprise Manager ?? Sun ZFS Storage Appliance ?????????????? Enterprise Manager ????????????????? 3??? Sun ZFS Stoarage Appliance ??????????????????? My Oracle Support ???Oracle Technology Network ???????????????????????????? ?????????????????????????? Oracle ZFS Storage Appliance Plugin Downloads Sun ZFS Storage Appliance ????????????????????????????? P.3 ???????????Appliance ???????????? Workflow ?????????? Enterprise Manager ???????????? P.10 ???????????????????????????????????????????Enterprise Manager 11g ??????????????????????? ??????????????????????????? ??????????????????????Sun ZFS Storage Appliance ??????????Database ???????????????????????????????Enterprise Manager ???????????????????????

    Read the article

  • Kingston SD reader not working for USB3

    - by user1146334
    I have a Kingston 4-in-1 Multimedia reader. When my PC was formatted with Win7 it worked fine. I decided to change to Ubuntu 14.04 and now it doesn't work. If I plug it into one of the USB2 ports it works fine, but whenever I plug it into one of the USB3 ports, it thinks about it for a minute and then dies. Here's the output of dmesg when it dies [110262.148656] usb 4-1: new SuperSpeed USB device number 3 using xhci_hcd [110262.170330] usb 4-1: Parent hub missing LPM exit latency info. Power management will be impacted. [110262.266379] usb 4-1: New USB device found, idVendor=11b0, idProduct=6348 [110262.266386] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [110262.266390] usb 4-1: Product: USB3.0 Media Reader [110262.266394] usb 4-1: Manufacturer: Kingston [110262.266398] usb 4-1: SerialNumber: 08735314400198 [110262.272929] usb-storage 4-1:1.0: USB Mass Storage device detected [110262.273239] scsi15 : usb-storage 4-1:1.0 [110263.290056] scsi 15:0:0:0: Direct-Access FCR-HS3 -0 1.00 PQ: 0 ANSI: 4 [110263.306622] scsi 15:0:0:1: Direct-Access FCR-HS3 -1 1.00 PQ: 0 ANSI: 4 [110263.323292] scsi 15:0:0:2: Direct-Access FCR-HS3 -2 1.00 PQ: 0 ANSI: 4 [110263.339858] scsi 15:0:0:3: Direct-Access FCR-HS3 -3 1.00 PQ: 0 ANSI: 4 [110263.340332] sd 15:0:0:0: Attached scsi generic sg3 type 0 [110263.340706] sd 15:0:0:1: Attached scsi generic sg4 type 0 [110263.340850] sd 15:0:0:2: Attached scsi generic sg5 type 0 [110263.340975] sd 15:0:0:3: Attached scsi generic sg6 type 0 [110264.651847] sd 15:0:0:1: [sde] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB) [110264.667049] sd 15:0:0:1: [sde] Write Protect is off [110264.667055] sd 15:0:0:1: [sde] Mode Sense: 2f 00 00 00 [110264.682767] sd 15:0:0:1: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [110264.694975] sd 15:0:0:2: [sdf] Attached SCSI removable disk [110264.697933] sd 15:0:0:3: [sdg] Attached SCSI removable disk [110264.729918] sd 15:0:0:0: [sdd] Attached SCSI removable disk [110264.754189] sde: sde1 [110264.760114] sd 15:0:0:1: [sde] Attached SCSI removable disk [110275.377368] usb 4-1: reset SuperSpeed USB device number 3 using xhci_hcd [110275.398453] usb 4-1: Parent hub missing LPM exit latency info. Power management will be impacted. [110275.436592] xhci_hcd 0000:05:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8802e4fb9980 [110275.436600] xhci_hcd 0000:05:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8802e4fb99c0 [110277.263444] usb 4-1: USB disconnect, device number 3

    Read the article

  • Auto backup a user folder to a usb when usb is plugged in

    - by Azztech Computers
    I'm a computer technician and help customers everyday with their computers and smartphones and have a really basic (i think) request but dont know how to go about it. Customer always come in with broken phones, water damage, needing updates, or just want me to backup their information. I currently have a program that i use when i backup their computers it backups their iOS folder C:\Users\USER\AppData\Roaming\Apple Computer\MobileSync\Backup but what i want is a quick easy way to do this in customers houses. What i require is a way when i plug in a USB drive it AUTOMATICALLY searches for the folder and starts transferring the folder to a predefined folder on the USB drive. This was I can just plug it in and begin work on their computer or phone without the risk of losing their information. I'm sure there is a .bat/.ini file i could use but wondering if someone has already done this or something similar as I would need it to search all the USER folders not just the one I'm logged into. Thanks in advance

    Read the article

  • Using UDF on a USB flash drive

    - by CesarB
    After failing to copy a file bigger than 4G to my 8G USB flash drive, I formatted it as ext3. While this is working fine for me so far, it will cause problems if I want to use it to copy files to someone which does not use Linux. I am thinking of formatting it as UDF instead, which I hope would allow it to be read (and possibly even written) on the three most popular operating systems (Windows, MacOS, and Linux), without having to install any extra drivers. However, from what I found on the web already, there seem to be several small gotchas related to which parameters are used to create the filesystem, which can reduce the compability (but most of the pages I found are about optical media, not USB flash drives). I would like to know: Which utility should I use to create the filesystem? (So far I have found mkudffs and genisoimage, and mkudffs seems the best option.) Which parameters should I use with the chosen utility for maximum compability? How compatible with the most common versions of these three operating systems UDF actually is? Is using UDF actually the best idea? Is there another filesystem which would have better compatibility, with no problematic restrictions like the FAT32 4G file size limit, and without having to install special drivers in every single computer which touches it?

    Read the article

  • Hard Reset USB in Ubuntu 10.04

    - by Cory
    I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: $ sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: $ sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on serverfault as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

    Read the article

  • Hard Reset USB in Ubuntu 10.04

    - by Cory
    I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: $ sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: $ sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on serverfault as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

    Read the article

  • bootable USB / installation requirements

    - by Chris Wilson
    Originally asked on One Hundred Paper Cuts Answers thread On the official site: http://www.ubuntu.com/netbook/get-ubuntu/download The instructions for creating a bootable USB key for installing Ubuntu Netbook Remix include a line saying: "Insert a USB stick with at least 2GB of free space" I recently installed UNR on a netbook -- in fact, the one I'm using right now -- and I went ahead despite only having a 1GB USB key on hand. Everything went smoothly and installed 100% correctly. If I had waited to go out and buy a 2GB USB key I would have spent that money unnecessarily and wouldn't have been able to use the computer in the meantime. I was wondering if there's a specific rationale for requiring a 2GB USB key, or if the instructions could be changed to indicate that it can be done with only 1GB. Thanks!

    Read the article

  • Unable to enumerate USB device

    - by takeshin
    Hello, My syslog is constantly filled with messages like this: Oct 16 11:48:35 my-laptop kernel: [61470.980078] hub 1-0:1.0: unable to enumerate USB device on port 2 Oct 16 11:48:35 my-laptop kernel: [61471.192079] hub 3-0:1.0: unable to enumerate USB device on port 2 The only USB device I use is Microsoft Natural Wireless Laser Mouse 7000. The laptop model is HP dv9500, Ubuntu 10.10, but the same was in the versions before. How can I fix this? Edit: Here's the output of sudo lsusb: Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 003: ID 045e:071d Microsoft Corp. Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub All USB devices seems to be working fine. I have some problems with DVD-R and sound card, but they are not USB.

    Read the article

  • USB gets disabled when i boot in linux (ubuntu 3.5.7)

    - by Gaurav Vyas
    I have connected USB keyboard & mouse to core i7 intel processor.When i boot my system in ubuntu with kernel 3.2.21 it runs properly i.e usb keyboard & usb mouse works satisfactorily. ISSUE When i boot my system in linux(ubuntu 3.5.7) USB keyboard & usb Mouse stops working.i have to boot my system by pressing "e" and then "Enter" i.e it directly links with the hardware.Mouse doesnt get power i.e LED under my optical mouse doesnt glow. kindly help me.

    Read the article

  • 'Invalid or corrupt kernel image' error while booting from USB stick

    - by steve
    I got the Ubuntu 11.10 32-bit edition and i used Unetbootin to write the ISO to a usb stick.After that i tried to boot from the stick,having changed the BIOS boot settings,and when the first interface shows up with the choices of istallation,whatever choice i select i got the message"invalid or corrupt kernel image".I use a netbook with windows 7 on it.I tried different usb sticks but same again.I also tried Universal USB installer instead of Unetbootin but same again.Any idea of what happens?I am using ASUS 1000H.The USB doesn't work in one more PC i tried to,but i also tried a second USB to both of the two computers and same again. I downloaded the ISO image once again and follow the same procedure but same again

    Read the article

  • Save to Hard Drive instead of bootable USB

    - by WAM
    I followed the instructions on the Ubuntu website on how to put Ubuntu 12.04 on a USB and make it a bootable USB stick for windows. It worked fine and I can boot up and run Ubuntu, but every time I try to download software or change settings it tries to save it to the USB rather than the hard drive built into the computer. The USB doesn't have enough space so the download fails and in addition it doesn't retain setting changes so when I restart my computer all the settings return to default and anything I saved is gone. Is there any way to change things so that when I download software or change settings Ubuntu will save it to my hard drive instead of the USB?

    Read the article

  • Unable to enumerate USB device on port 2 when connecting Android phone

    - by ProfessionalAmateur
    I'm running Ubuntu 11.10 (64-bit) as a VirtualBox guest on a Win7 64-bit host. When I plug in my Android Epic4g (Galaxy S) both the host and guest see the device properly, however lsusb does not. When I run dmesg I get the following: [ 361.664219] usb 1-2: new full speed USB device number 79 using ohci_hcd [ 362.428798] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 363.313782] hub 1-0:1.0: unable to enumerate USB device on port 2 I get the same type of dmesg message with the USB 2.0 (ECHI) Controller enabled and disabled for the guest OS. I'm stuck with this one, can anyone help?

    Read the article

  • After making boot disk using rufus in usb 3.0 port, it doesn't work in another ports.

    - by sin
    I have a big problem! After making boot disk using rufus in usb 3.0 port, it doesn't work in another ports. I have to install windows in other PC which has usb 2.0port only! so I made usb booting disk using usb 3.0 in 3.0 port. but after that it never worked except in 3.0 ... and I could't restore my usb. I alredy fomated in cmd and others in usb3.0 port! but there is no change. and I couldn't find it in usb 2.0 port. plz help me.

    Read the article

  • Any large USB sticks with integrated card readers?

    - by Al
    I have one of Kingston's DataTraveller Micro Reader USB sticks, a fantastic memory stick with an integrated micro SD and M2 card reader. However, I've gradually filled it to the brim and am looking for a larger stick. Unfortunately, Kingston don't make them any bigger than the 4GB one that I currently have and I was hoping to go to 16GB now that they've come down in price. Does anyone know if any manufacturers make something similar: a 16GB stick with a micro SD card reader integrated (I'm not bothered about the M2 reader).

    Read the article

  • Putty can't connect to USB modem on Windows 7

    - by IanM
    I'm trying to configure caller id on a USB modem connected to a Windows 7 x32 machine. Hyperterminal isn't available so I downloaded the latest version of Putty and am using the Serial option. I'm using the modem's COM port details from Device Manager (COM5, 115200 baud), but when I open the putty session it just hangs with the cursor at the top left hand corner. Hitting the Enter key does nothing. Any ideas??

    Read the article

  • Recognition of USB drive

    - by lamcro
    I have a Motorola phone, with a MicroSD slot, which my Ubuntu machine does not recognize as a USB drive. It does know there is something there since It automatically charges my phone whenever I connect it. using the command lsusb shows it as "Motorola PCS" Is there a way to tell Ubuntu/Linux that the connected hardware is a disk drive?

    Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >