Search Results

Search found 7216 results on 289 pages for 'low cost'.

Page 80/289 | < Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >

• Hardware Requirements & Tuning - Flash Media Server 3.5 Interactive

  - by Anthony Kanago

  I am trying to spec out a server to purchase (physically, not rented from someone like softlayer.com) to run an intranet instace of Flash Media Server 3.5 Interactive. In general, the server will likely be fielding somewhere on the order of 400 connections at a time at the upper limit. Of course, should this increase, we don't want to be stuck. While the decision is not final, we will likely be running the server on Red Hat rather than Windows. The server will be run on gigabit ethernet. I have two related questions: What sort of hardware would I need realistically to support this? What advice can you offer for settings in tuning FMS/the OS to be performant to this level? We are looking for a bare minimum that will run this effectively to save on costs. Realistically, the average number of connections will be fairly low (50-150) by comparison with that upper limit estimate. To reiterate: we just want to be cautious in not getting caught when we need more power, but we also need a low-cost solution (doesn't everyone?) and that may take priority. Windows and RedHat are the two officially supported operating systems. Since FMS is stated to be 32-bit only, I'm sticking with a 32-bit OS. The hardware requirements listed by Adobe on their website are: 3.2GHz Intel® Pentium® 4 processor (dual Intel Xeon® or faster recommended) 2GB of RAM (4GB recommended) 1Gb Ethernet card So what realistically do I need for those sorts of connection numbers, and what can I due to tune things up to get more out of less hardware? Thanks!

  Read the article

• SSL on local sub-domain and sub-sub-domain

  - by Eduard Luca

  I have both local.domain.com and lmarket.local.domain.com pointing to my localhost from etc/hosts. The problem is that I am using XAMPP on Windows 7, and have 2 SSL VirtualHosts in my apache config, but no matter which one I access, I am taken to local.domain.com. On non-HTTPS requests all works fine, and the vhosts are basically the same. Here is the relevant part of my vhosts: <VirtualHost local.domain.com:443> DocumentRoot "C:/xampp/htdocs/local" ServerName local.domain.com ServerAdmin webmaster@localhost ErrorLog "logs/error.log" <IfModule log_config_module> CustomLog "logs/access.log" combined </IfModule> SSLEngine on SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL SSLCertificateFile "conf/ssl.crt/server.crt" SSLCertificateKeyFile "conf/ssl.key/server.key" <FilesMatch "\.(cgi|shtml|pl|asp|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory "C:/xampp/cgi-bin"> SSLOptions +StdEnvVars </Directory> BrowserMatch ".*MSIE.*" nokeepalive ssl-unclean-shutdown downgrade-1.0 force-response-1.0 CustomLog "logs/ssl_request.log" "%t %h %{SSL_PROTOCOL}x %{SSL_CIPHER}x \"%r\" %b" </VirtualHost> <VirtualHost lmarket.local.domain.com:443> DocumentRoot "C:/xampp/htdocs/lmarket.local" ServerName lmarket.local.domain.com ServerAdmin webmaster@localhost ErrorLog "logs/error.log" <IfModule log_config_module> CustomLog "logs/access.log" combined </IfModule> SSLEngine on SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL SSLCertificateFile "conf/ssl.crt/server.crt" SSLCertificateKeyFile "conf/ssl.key/server.key" <FilesMatch "\.(cgi|shtml|pl|asp|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory "C:/xampp/cgi-bin"> SSLOptions +StdEnvVars </Directory> BrowserMatch ".*MSIE.*" nokeepalive ssl-unclean-shutdown downgrade-1.0 force-response-1.0 CustomLog "logs/ssl_request.log" "%t %h %{SSL_PROTOCOL}x %{SSL_CIPHER}x \"%r\" %b" </VirtualHost> If I invert these blocks, then the opposite happens: local.domain.com goes to lmarket.local.domain.com. Any help would be appreciated.

  Read the article

• Cannot upload files bigger than 8GB to Amazon S3 by multi-part upload due to broken pipe

  - by spencerho

  I implemented S3 multi-part upload, both high level and low level version, based on the sample code from http://docs.amazonwebservices.com/AmazonS3/latest/dev/index.html?HLuploadFileJava.html and http://docs.amazonwebservices.com/AmazonS3/latest/dev/index.html?llJavaUploadFile.html When I uploaded files of size less than 4 GB, the upload processes completed without any problem. When I uploaded a file of size 13 GB, the code started to show IO exception, broken pipes. After retries, it still failed. Here is the way to repeat the scenario. Take 1.1.7.1 release, create a new bucket in US standard region create a large EC2 instance as the client to upload file create a file of 13GB in size on the EC2 instance. run the sample code on either one of the high-level or low-level API S3 documentation pages from the EC2 instance test either one of the three part size: default part size (5 MB) or set the part size to 100,000,000 or 200,000,000 bytes. So far the problem shows up consistently. I attached here a tcpdump file for you to compare. In there, the host on the S3 side kept resetting the socket.

  Read the article

• E-mail hosting provider that can set up aliases with wildcards

  - by Richard Downer

  I am looking for an e-mail hosting provider that allow e-mail aliases containing wildcards. In more detail: I own my own domain. I want an e-mail hosting provider to manager e-mail for my domain. Now, to help deal with spam, I often give different e-mail addresses to different organisations. These e-mail addresses always start with the same prefix, but then differ. So, for example, I might give out these e-mail addresses: [email protected] [email protected] [email protected] I want to be able to go to the e-mail provider's control panel and set up an e-mail alias like this: [email protected] -- bounce/discard (because this address has been sold to spammers) joe-*@sample.com -- redirect to [email protected] What's I don't want to do is either have to set up every single e-mail address individually (because I make them up whenever I need them), nor do I want to have a general catch-all for any unrecognised address in my domain (because I don't want to be carpet-bombed with spam when a spammer runs a dictionary attack against my domain name.) Although this seems like a useful feature to have, it seems to be a little-known feature and I've not seen anybody advertise this feature. My current hosting provider offer this but I want to move away from them, so I need another provider that will continue to work with all the e-mail addresses I've been using for years. Alternatively, I could use mail server software that runs on Windows - I have seen some commercial packages offering this feature but they cost more than I can afford - are there any suggestions for low-cost software packages?

  Read the article

• How to increase wifi speed for laptops

  - by sagar

  Now, Let me explain the situation. I am having a query regarding Wi-Fi network. I am having PC & laptop. I requested my Wi-Fi providers that I want connection in my PC. So that - Wi-Fi provider set up an Antenna on my building Terrace - They joined a cable to pc & that Antenna. ( I think using RJ45 connector ) - The reason behind this - my does not have a built in Wi-Fi adapter. Now - almost laptops have built in Wi-Fi. Now - On terrace there is Wi-Fi with superb speed. But on my flat - Wi-fi comes with low speed. So, when ever I use internet on my pc - it has great speed - but my laptop works with low speed. The reason behind this - PC is catching wifi from terrace & laptop is catching the wifi from it's own place. Now, My question is something like this. Can we place an antenna or something like that & connect it to laptop for better wifi speed? ( I am not technical person - Please add comment for down vote - if any ) ( Please add comment for more explanation of my Problem ) Thanks in advance for sharing your knowledge. Sagar

  Read the article

• Alternatives to Splunk?

  - by MichaelGG

  I'm pretty impressed with Splunk, especially version 4. Pretty graphs, alerting (Enterprise only), and fast, accurate, searching. It's a great product. However, the cost just way too high to consider for full production use for our company. All we really need is to be able to index different logs in a central place, and have reasonable searching on that. Having alerts based on a saved search is also really nice. We don't really go beyond that. In fact, our biggest usage has been in deploying new applications. Everything gets logged via log4net to either the Event log on Windows or a text file on Linux. Splunk makes it pretty easy to quickly search across those to make sure all the parts of the app are working ok -- that's saved us tons of time versus hunting down individual logging sources. What alternatives exist in this market? I have a sinking feeling Splunk's pricing is so high because they have the best product by far, and they know it. We want the server to run on Windows. I'd be open to a split model, using one product for general logs (collect via syslog/Snare), and a dedicated product for our custom apps (like Log4Net Dashboard). Would using a simple syslog server such as Kiwi, sent to SQL Server (perhaps with fulltext enabled) work? I'd hope the cost should be well under 5 figures, USD. (And yes, I know, we're cheap. We're a startup with little money, and BizSpark takes care of all our MS licensing.) Edit: I should add, we have about 10 physical servers, 20 VMs, and a couple firewalls and switches. 90% is Windows.

  Read the article

• Bridged network on OS X only gets UDP broadcast traffic

  - by a paid nerd

  I've created a bridged network Mac OS X 10.8.5 using ifconfig and TUNTAP for OS X to bridge my wireless connection, en0, with a virtual interface, tap0, which I can use for guest VMs: $ sudo sysctl -w net.inet.ip.forwarding=1 $ sudo sysctl -w net.link.ether.inet.proxyall=1 $ sudo sysctl -w net.inet.ip.fw.enable=1 $ sudo ifconfig bridge0 create $ sudo ifconfig bridge0 addm en0 addm tap0 $ sudo ifconfig bridge0 up $ ifconfig en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 28:cf:xx:xx:xx:xx inet6 xxxx::xxxx:xxxx:xxxx:xxxx%en0 prefixlen 64 scopeid 0x4 inet 192.168.100.64 netmask 0xffffff00 broadcast 192.168.100.1 media: autoselect status: active bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether ac:de:xx:xx:xx:xx Configuration: priority 0 hellotime 0 fwddelay 0 maxage 0 ipfilter disabled flags 0x2 member: en0 flags=3<LEARNING,DISCOVER> port 4 priority 0 path cost 0 member: tap0 flags=3<LEARNING,DISCOVER> port 8 priority 0 path cost 0 tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether ca:3d:xx:xx:xx:xx open (pid 88244) However, if I tcpdump -i tap0, I only see broadcast traffic. Shouldn't I see a mirror of everything on en0? (192.168.100.33, the host doing the broadcasting, is another unrelate, noisy server on my LAN.) (I asked a similar question here and will probably close it.)

  Read the article

• Cheapest iSCSI SAN for Windows 2008/SQL Server clustering?

  - by MichaelGG

  Are there any production-quality iSCSI SANs suitable for use with Windows Server 2008/SQL Server for failover clustering? So far, I've only seen Dell's MD3000i, and HP's MSA 2000 (2012i), which both are around $6K with a minimal disk configuration. Buffalo (yea, I know), has a $1000 device with iSCSI support, but they say it will not work for 2008 failover clustering. I'm interested in seeing something suitable for failover in a production environment, but with very low IO requirements. (Clustering, say, a 30GB DB.) As for using software: On Windows, StarWind seems to have a great solution. But it's actually more money than buying a hardware SAN. (As I understand, only the enterprise edition supports having replicas, and that's $3000 a license.) I was thinking I could use Linux, something like DRBD + an iSCSI target would be fine. However, I haven't seen any free or low-cost iSCSI software that supports SCSI-3 persistent reservations, which Windows 2008 needs for failover clustering. I know $6K isn't much at all, just curious to see if there are practical cheaper solutions out there. And finally, yes, the software is expensive, but many small business get MS BizSpark, so the Windows 2008 Enterprise / SQL 2008 licenses are completely free.

  Read the article

• Better way to design a database

  - by cMinor

  I have a conceptual problem and I would like to get your ideas on how I'll be able to do what I am aiming. My goal is to create a database with information of persons who work at a place depending on their profession and skills,and keep control of salary and projects (how much would cost summing all the hours of work) I have 3 categories which can have subcategories: Outsourcing Technician welder turner assistant Administrative supervisor manager So each person has its information and the projects they are working on, also one person may do several jobs... I was thinking about having 5 tables (EMPLOYEE, SKILLS, PROYECTS, SALARY, PROFESSION) but I guess there is a better way of doing this. create table Employee ( PRIMARY KEY [Person_ID] int(10), [Name] varchar(30), [sex] varchar(10), [address] varchar(10), [profession] varchar(10), [Skills_ID] int(10), [Proyect_ID] int(10), [Salary_ID] int(10), [Salary] float ) create table Skills ( PRIMARY KEY [Skills_ID] int(10), FOREIGN KEY [Skills_name] varchar(10) REFERENCES Employee(Person_ID), [Skills_pay] float(10), [Comments] varchar(50) ) create table Proyects ( PRIMARY KEY [Proyect_ID] int(10), FOREIGN KEY [Skills_name] varchar(10) REFERENCES Employee(Person_ID) [Proyect_name] varchar(10), [working_Hours] float(10), [Comments] varchar(50) ) create table Salary ( PRIMARY KEY [Salary_ID] int(10), FOREIGN KEY [Skills_name] varchar(10) REFERENCES Employee(Person_ID) [Proyect_name] varchar(10), [working_Hours] float(10), [Comments] varchar(50) ) So to get the total amount of the cost of a project I would just sum the working hours of each employee envolved and sum some extra costs in an aggregate query. Is there a way to do this in a more efficient way? What to add or delete of this small model? I guess I am missing something in the salary - maybe I need another table for that?

  Read the article

• LSI 9260-8i w/ 6 256gb SSDs - RAID 5, 6, 10, or bad idea overall?

  - by Michael Pearson

  We're provisioning a new production server for our reasonably busy website. Our choice of host have available a 6 drive configuration with a LSI 9260-8i card. My initial thought was to fill all six bays with SSDs (Intel 520 256gb) and set them up in RAID. Good, bad, or terrible idea? Can the card handle it? Should we be using RAID 5, 6 or 10? This would be the first time the provider have filled all six slots for this rackmount with SSDs, so they're a bit hesitant. I'm wondering if somebody else with this card has done something similar in a production environment. We do about 43gb of writes per day and currently use about 300gb of storage. The server acts as webserver, database, and image store for approx 1 million files. The plan is to underprovision the SSDs by approximately 10% to 20% to increase their overall lifespan & performance. The fallback option is 2x480gb SSDs in RAID 1 and another 2x1TB HDDs in RAID 1. The motivation behind this is that the server rental cost difference between 2xSSDs and 6xSSDs is minimal (compared to the overall cost of the rental). We do not have any special high-IOPs requirements. However, if the configuration is known to work, I don't see a good reason to not use it and not have to worry about having separate 'fast and small' and 'slow and large' disks.

  Read the article

• How to let MSN or Yahoo Messenger set you to be Invisible or Offline when you are idle for an hour?

  - by Jian Lin

  The short question is: How do we let MSN or Yahoo Messenger set us to be Invisible or Offline when we are idle for half an hour or an hour? The reason is: if I am on 24 hours a day, some people see me as weird. Some people see my value as low, because I am always there. There are ways to set me to "Away" or "Busy" after 10 minutes, but there seems to be no way to set myself to invisible or offline after 1 hour. As I am a software developer, I am very used to turning the computer on 24 hours a day. (for example, for checking email for urgent fixes, and fix issue and push to web server). We don't turn off computer usually even when we sleep, because we may sometimes can't sleep yet and come check on the computer, or wake up in the morning and immediately need to check if everything is ok. But, my MSN and Yahoo Messenger is always on for 24 hours a day, and I found that some girls start to ask me why I am always there 24 hours a day (even though they see me as away or busy, their feeling is that I am always there). What's more, I found that since I am always there, my value actually drop in their eyes, because hard to get = high value, and always there = low value. Some people feel me as having nothing much to do, always in front of computer, or what is he doing in front of computer so much? Now since it is my job, and I need to read emails once in a while, I am in fact in front of the computer more than some other people. I am in front of the computer maybe 10 hours a day, far from 24 hours a day. Is there an easy and automatic solution to this?

  Read the article

• cPanel web server redundancy advice?

  - by crgnz

  At present I operate a (reasonably low volume) web-hosting service with a Centos 5.3 server running cPanel/WHM. I would like to implement a level of redundancy such that in the event of server failure, I can restore service with a minimum of effort in less than 60 minutes. I also want to setup a secondary DNS that cPanel will replicate with. My current idea is to kill two birds with one stone by: My current server is called "www1" Purchase an identical server (HP DL360 G4) with mirrored disks. Call this server "www2" Install Centos 5.4 (or perhaps I should install 5.3 to be identical with www1) Install cPanel/WHM on this server and fully license it Setup www1 and www2 cPanel to replicate DNS with each other Setup a nightly replication script that does the following: a) rsync's the /home directory from www1 to www2 b) dumps all MySQL databases on www1 and copies them to a temp folder (with root access only) on www2 c) triggers a script to run on www2 that restores the MySQL dumps Thus each night a fully working copy of all the websites and MySQL databases is copied to www2. I do not have enough knowledge of MySQL replication to understand if it works safely and transparently with cPanel. Thus I propose the mysql dump/copy/restore due to not knowing any better! In the event that www1 dies a horrible death, I envisage that I could login to www2, change the IP addresses to those that www1 had, and presto, the websites are available again. The advantage of this idea is that it is fairly simple and "low tech" and thus does not require an expert sysadmin to setup and monitor (I am NOT an expert sysadmin) The disadvantage of this idea is that up to a full days worth of data changes would be lost. I think this would be acceptable to the sorts of customers I host at the moment. The other disadvantage would be having to pay for a full cPanel license, but I am comfortable with that cost, so for now all I want to discuss are technical considerations. Is this a sound scheme?

  Read the article

• On Windows and Windows 7's Task Manager, why Memory is 1118MB Available but only 62MB Free? [closed]

  - by Jian Lin

  Possible Duplicate: Windows 7 memory usage What are the "Cached", "Available", and "Free" memory in the following picture (From Windows 7's Task Manager). If it is 1118MB Available, then why isn't it Free (to use)? As I understand it, if a bowl of noodle is available, that doesn't mean it is free... it may still cost $7. But what about in the Task Manager, when it is Available, it is also not Free? Does it cost $2 per MB? What about the "Cached"... What exactly is the Cached Memory? We may put some hard disk data in RAM and so we cache the data in RAM, for faster access (that's the operating system's job). So the Total Physical RAM is 6GB, what is the 1106 Cached? Cached in where? Caching physical RAM in ... some where? It is also strange that the Cached value is sometimes higher and sometimes lower than the Available value. Can somebody who is knowledgeable about this shred some light on these meanings?

  Read the article

• How do I configure nVidia drivers on a Portable Ubuntu setup?

  - by Nicholas Flynt

  I've been pulling my hair out over this one for a couple of days now, google is no help. I've created a wonderful (until this issue) portable copy of Ubuntu linux that will boot on mostly anything by using a USB enclosure for my laptop's 80GB SATA drive. So far so good, it boots and runs on everything, and on non-nVidia card setups was even detecting the drivers, or letting me install the required drivers for hardware acceleration and compiz. Because you know, the wobble windows are the most awesome thing ever. Anyway, my desktop machine had an nVidia card, so I'm thinking, sure, I'll just install the nVidia drivers like before and everything will work happily. Not so-- now the desktop and any other nVidia cards work great, but it seems to have completely disabled any other graphics cards. When the kernel module detects that an nVidia card isn't present, it shoots up this nasty little dialog box giving me the option to boot into "low graphics" mode, which doesn't even allow me to use the correct screen resolution, much less see the installed graphics card and try to configure a driver for it. Is there any way to configure Ubuntu (with the dreaded nVidia kernel module) so that it can use nVidia's drivers when an nVidia card is present, and default to the normal (not low-graphics) setup in other cases, so that it has a fair chance of using what's actually present? I'm not afraid to much with config files, I just don't know the underlying system well enough to feel comfortable diving in without a push in the right direction. Thanks guys!

  Read the article

• online backup plan for a home office with servers

  - by TiernanO

  So, i am in the process of tweaking my spending and i need to change my backup plan... I am currently using a mix of JungleDisk and ZManda ZCB to backup files on my MacBook Pro, Main Windows Server Wrokstation, a dedicated Windows Server in a datacenter, and various other machines and file sources. The problem is the cost: this month, it has cost me about $90 to backup a little over 500Gb... This amount of data will increese over time too, since i am backing up Photos (24Mb RAW images + 4-8MB JPEGs), Videos (various cameras shooting 720p and 1080p), Music, Movies, TV shows and Apps from iTunes (though with iTunes cloud, this might not need to be backed up again) and source code... I have looked at the likes of Mozy, CrashPlan+ and Pro, Backblaze and Carbonite, but each have their problems: Mozy seems overly expenvice per gig at 50C Crashplan wont sell to me since i am outside the US (they hide it on their site... hidden in the FAQ section!) Backblaze dont support Windows Server Carbonite business pricing is $600 up front for 500Gb of storage... Fro $229, they will not backup Windows Servers. So, other than those, Jungle Disk (at 15c per Gig) or ZManda (also at 15c per Gig) what other options are there? what are other people using?

  Read the article

• High latency issue for web service call from amazon aws ec2 to local server

  - by SibzTer

  We have a legacy web application that is running in our data center on premises located in Houston. We have a developed a new .net 4 based web application in order to provide new features to customers. The new web application is hosted in amazon aws ec2 environment (N. Virginia region us-east-1b zone). In order to get seamlessly integrate with the legacy application the new web application makes web service calls to retrieve data. We are seeing an unusually high latency time in the order of 5+ seconds for these web service calls. The exact same web service call returns in less than a second on our local PCs (which makes sense given physical proximity to the actual server). The weird part is that we have developers in California who also have the same milliseconds response time. We are testing the web service response using third party tools such as SoapUI, Google Chrome extensions such as Advanced REST Client, Postman REST Client, etc. As if this wasnt weird enough, we have noticed the same low latency from certain other ec2 instances while testing which are in the same region and availability zone as well. If we experienced the high latency consistently from all the ec2 instances I could understand. But there is something else going on. Comparing the various stats and results between the low latency and high latency ec2 servers do not show any significant differences: ping (constant 40ms), tracert, winmtr, etc. We have instances that are in the VPC as well. So I tried both the public and private IP address of the web service host server and that didnt make a difference either for the above results. We need to resolve this latency issue as this is causing the resulting web pages to load very slowly (almost 15+ seconds which is simply unacceptable). The ec2 instances have Windows Server Datacenter 64 bit. Let me know if there is any other infor I can provide to help diagnose this.

  Read the article

• What's the state of the art in image upscaling?

  - by monov

  I like to collect cool pics and use them as wallpapers or for other things. Often, artists publish only low-res versions, probably for fear of theft. Example: Gabriel Pulecio's BIRDS Now, if I want to use that as a wallpaper, I'd have to upscale it, and obviously that'd make it look blurry because of the bicubic interpolation. I realize there's no real way to get a high-res version from a low-res pic, because the information is not simply there. That said, I'm wondering if heuristics have been developed for upscaling with less apparent loss of quality. Those would probably be optimized for specific image types. For photorealistic pictures, for cartoons with large flat areas, for pixel art... One algorithm I'm aware of is Seam Carving. It works for some kinds of pics, especially ones with a plain, undetailed or uninteresting background, and a subject that strongly stands out. But it's far from being general-purpose. Applying it to the above pic produces this. It looks quite sharp, but the proportions are horribly distorted because the algorithm is not designed for this kind of pic. Another is Pixel art scaling algorithms. Those are completely unfit for anything other than actual pixel art that's pixelized to begin with. For example, I tried the scale2x windows binary on my pic, but its output was nearly indistinguishable from nearest-neighbour scaling because the algorithm didn't detect any isolated pixely fragments to work from. Something else I tried was: I enlarged the image in Photoshop with bicubic interpolation, then I applied unsharp mask. The result looks pretty bad. The red blotch is actually resized reasonably well, but the dove is far from it. What I'm looking for is some app that makes a best-effort attempt at upscaling any input image while minimizing blurriness. If you know of any, I'll be thankful. Note that the subjective prettiness and sharpness of the result is what matters... the result doesn't need to be completely faithful to the original small image.

  Read the article

• Win 2008 R2 - copying TO disk is very slow, copying FROM is more or less okay

  - by avs099

  I have Windows 2008 R2 SP1 with 4 identical SATA disks (Seagate Barracude 7200) in RAID 5 array. It has 4Gb of memory; all recent updates are installed. Problem: when I copy large file from one folder to another, I get about 10MB/s average speed. When I read this file from network share via 1Gbps connection - I get about 25-30 MB/s. Both numbers seems to be low for me - but specifically I'm very frustrated with low write speed. there is no antivirus, no hyper-v, it's just a fileserver - i when i do my tests nobody else reads/write from it (we have only 4 people in a team, so I'm sure). Not sure if that matters, but there is only 1 logic disk "C" with all available space (1400 GB). I'm not an admin at all, so I have no idea where to look and what other information to provide. I did run performance monitor with "% idle time", "avg bytes read", "avg byte write" - here is the screenshot: I'm not sure why there are such obvious spikes. Any idea? Please let me know if you need me to provide more information - what counters should I check, etc. I'm very eager to get this solved. Thank you. UPDATE: we have another Windows 2008 R2 SP1 server with 2 RAID1 arrays - one is disk C (where windows is installed, another one is disk E). It is running Hyper-V and does not have antivirus. I noticed the following behavior when I copy large file (few GBs): C - C: about 50MB/sec C - E: about 55MB/sec E - E: 8MB/sec!!! E - C: 8MB/sec!!! what could cause this?? E drive is RAID1 array from same Seagate Barracuda 1TB drives..

  Read the article

• linux Firewall question

  - by bcrawl

  I have few generic questions about firewalls and I thought the community up here could help me out. 1) So I recently installed Ubuntu server barebones. I checked for open ports, none were open which was great. Is that because there was a firewall installed or was it because there were no applications installed? 2) I installed some applications, (Apache, postgres,ssh, Java app and some few). Between these, I ended up opening a few ports (~10). Now I have a list of all the ports I would need open. So, how do I go about protecting them? [Is this the right question to ask? does the process go like this, Install Firewall - Allow Said needed ports - deny rest using IPtables rules] This is going to be open to the internet. Hosting low traffic ecommerce sites. 3) What do you think is the easiest way for me to quasi-secure the server, [low maintenance overhead/simplicity. Any open source "software" which can make my life easier?] 4) Finally, of the said open ports [2], I have 2 ports I need to close because they are telnet ports. Can I close these ports without installing a "firewall" Thanks all for the help and Merry Christmas!!!!!!!

  Read the article

• How do I create a wifi network bridge with qemu on OS X?

  - by a paid nerd

  I grabbed a small FreeBSD live CD and QEMU, and I'm trying to bridge my Mac OS X 10.8 wifi connection so that the guest OS is available on my LAN. However, the guest OS never gets a DHCP lease. This works perfectly with VirtualBox in their "bridged" network mode, so I know it can be done. I need to get it working with QEMU because VirtualBox doesn't support the architecture that I need for this project. Here's what I've done so far based on hours of googling: Installed TUNTAP for OS X Told OS X to supposedly forward all packets, even ARP: (NOTE: This doesn't appear to work.) $ sudo sysctl -w net.inet.ip.forwarding=1 $ sudo sysctl -w net.link.ether.inet.proxyall=1 $ sudo sysctl -w net.inet.ip.fw.enable=1 Created a bridge: $ sudo ifconfig bridge0 create $ sudo ifconfig bridge0 addm en0 addm tap0 $ sudo ifconfig bridge0 up $ ifconfig bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether ac:de:xx:xx:xx:xx Configuration: priority 0 hellotime 0 fwddelay 0 maxage 0 ipfilter disabled flags 0x2 member: en0 flags=3<LEARNING,DISCOVER> port 4 priority 0 path cost 0 member: tap0 flags=3<LEARNING,DISCOVER> port 8 priority 0 path cost 0 tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether ca:3d:xx:xx:xx:xx open (pid 88244) Started tcpdump with -I in the hopes that it enables promiscuous mode on the wifi device: $ sudo tcpdump -In -i en0 Run QEMU using the bridged network instructions: $ qemu-system-x86_64 -cdrom mfsbsd-9.2-RELEASE-amd64.iso -m 1024 \ -boot d -net nic -net tap,ifname=tap0,script=no,downscript=no But the guest system never gets a DHCP lease: If I tcpdump -ni tap0, I see lots of traffic from the wireless network. But if I tcpdump -ni en0, I don't see any DHCP traffic from the QEMU guest OS. Any ideas? Update 1: I tried sudo defaults write "/Library/Preferences/SystemConfiguration/com.apple.Boot" "Kernel Flags" "net.inet.ip.scopedroute=0" and rebooting per this mailing list suggestion, but this didn't help. In fact, it made VirtualBox bridged mode stop working.

  Read the article

• How to set minimum SQL Server resource allocation for a database?

  - by Jeff Widmer

  Over the past Christmas holiday week, when the website I work on was experiencing very low traffic, we saw several Request timed out exceptions (one on each day 12/26, 12/28, 12/29, and 12/30) on several pages that require user authentication. We rarely saw Request timed out exceptions prior to this very low traffic week. We believe the timeouts were due to the database that it uses being "spun down" on the SQL Server and taking longer to spin up when a request came in. There are 2 databases on the SQL Server (SQL Server 2005), one which is specifically for this application and the other for the public facing website and for authentication; so in the case where users were not logged into the application (which definitely could have been for several hours at a time over Christmas week) the application database probably received no requests. We think at this point SQL Server reallocated resources to the other database and then when a request came in, extra time was needed to spin up the application database and the timeout occurred. Is there a way to tell SQL Server to give a minimum amount of resources to a database at all times?

  Read the article

• How do hdparm's -S and -B options interact?

  - by user697683

  These two options seem confusing. For example: according to the man page -B 254 "does not permit spin-down". However, testing with -B 254 -S 1 the drive does spin down after 5 seconds. -B Query/set Advanced Power Management feature, if the drive supports it. A low value means aggressive power management and a high value means better performance. Possible settings range from values 1 through 127 (which permit spin-down), and values 128 through 254 (which do not permit spin-down). The highest degree of power management is attained with a setting of 1, and the highest I/O performance with a setting of 254. A value of 255 tells hdparm to disable Advanced Power Management altogether on the drive (not all drives support disabling it, but most do). -S Put the drive into idle (low-power) mode, and also set the standby (spindown) timeout for the drive. This timeout value is used by the drive to determine how long to wait (with no disk activity) before turning off the spindle motor to save power. Under such circumstances, the drive may take as long as 30 seconds to respond to a subsequent disk access, though most drives are much quicker. The encoding of the timeout value is somewhat peculiar. A value of zero means "timeouts are disabled": the device will not automatically enter standby mode. Values from 1 to 240 specify multiples of 5 seconds, yielding timeouts from 5 seconds to 20 minutes. Values from 241 to 251 specify from 1 to 11 units of 30 minutes, yielding timeouts from 30 minutes to 5.5 hours. A value of 252 signifies a timeout of 21 minutes. A value of 253 sets a vendor-defined timeout period between 8 and 12 hours, and the value 254 is reserved. 255 is interpreted as 21 minutes plus 15 seconds. Note that some older drives may have very different interpretations of these values.

  Read the article

• Triple-monitor set-up (2 unique, 1 cloned): Can a VGA splitter be used on one output of a dual-head

  - by stakx

  Background: I'm currently researching hardware components for some kind of information terminal we're building. This application of ours makes use of three output screens: (1) A touch screen where all user input is made; (2) A regular LCD monitor where the requested information is being displayed; and (3) A projector which displays exactly the same signal as screen (2) does. (All screens will run at the same resolution of 1024x768 btw.) Now I figured that using a dual-head video card would be sufficient, let's say a Matrox P690 low-profile PCI card. This would involve having a Y cable connected to the graphics card itself, then two DVI-to-VGA adapters at each end of the Y cable, and then having a VGA splitter on one of the VGA outputs. The following shows the setup in question: 0--1---------2-> VGA (DSUB-15) \ \ ----2-3---------> VGA (DSUB-15) \ \ -----------------> VGA (DSUB-15) 0: graphics card (LFH60 jack) 1: LFH60 to DVI-I dual monitor Y cable 2: DVI-to-VGA adapters 3: VGA splitter cable Question(s): Will this work? I'm particularly concerned about the following points: Can a low-profile PCI video card output a signal which is strong enough for three monitors (even if it's a dual-head card)? Does the combination of so many adapters and splitter cables work? (The LFH-to-DVI cable comes with the video card) Will the VGA splitter cable degrade the signal on the output screen & projector significantly? (If so, would a USB-powered splitter cable remedy this problem?) I can't possibly expect anyone to answer all those questions, but any input is appreciated.

  Read the article

• Looking for suitable backup solution Mac OS X to offsite Centos 6 server 1TB of working data

  - by Brady

  I'll start by saying what we have in place currently: On site file server (Mac OS X Server) that is used by GFX designers and they have a working 1TB of data. Offsite server with 2TB available storage (Centos 6) Mac OS X server rsync data to offsite server every 6 hours (rsync -avz --delete --progress -e ssh ...) Mac OS X server does full data backup to LTO 4 tape on a 10 day recycle (Mon-Fri for 2 weeks) rsync pushes about 60GB of file changes a day. The problem: The onsite tape backup is failing as 1TB of graphics files don't compress well to fit onto a 800GB LTO4 tape. Backup is incredibly slow doing a full backup. Pain in the backside getting people to remember to change the tape. Often gets forgotten etc The quick solution: Buy LTO5 Drive and tapes. However this has been turned down because of the cost... What I would like: Something that works in the same way rysnc works. Only changed data is sent over the wire and can be scheduled to run multiple times during the day. Data that is sent is compressed and sent over SSH. Something that keeps a 14day retention but doesn't keep duplicate data So as an example if I have 1TB of working data and 60GB of changes are made each day then I expect around 1.84TB of data to be stored on the offsite server. To work with the Mac OS X server and Centos 6 server. Not cost an arm and a leg. Must be a cheaper solution than buying an LTO5 drive with tapes (around £1500). Be able to be setup to run autonomously. Have some sort of control panel that will allow an admin to easily restore a file/folder. Any recommendations?

  Read the article

• Excel chart with year-to-year comparison

  - by Craig

  Given this data: Date Year Month Usage (Kw-h) Cost/Month 02/19/08 2008 2 501 59.13 03/18/08 2008 3 404 48.49 04/16/08 2008 4 387 45.67 05/22/08 2008 5 319 37.85 06/23/08 2008 6 363 43.81 07/23/08 2008 7 372 48.86 08/21/08 2008 8 435 59.74 09/23/08 2008 9 358 49.9 10/16/08 2008 10 313 42.01 11/20/08 2008 11 328 39.99 12/16/08 2008 12 374 44.7 01/20/09 2009 1 474 55.35 02/19/09 2009 2 444 52.85 03/19/09 2009 3 398 49.25 04/17/09 2009 4 403 51.05 05/19/09 2009 5 405 49.61 06/18/09 2009 6 373 45.18 07/20/09 2009 7 337 44.67 08/18/09 2009 8 369 50.73 09/17/09 2009 9 377 52.36 10/16/09 2009 10 309 43.4 11/17/09 2009 11 249 34.14 12/16/09 2009 12 327 41.79 01/20/10 2010 1 356 45.66 I would like to produce a report that displays a Usage (Kw-h) line for each year. Features: Y axis: Usage (Kw-h) X axis: Month Line 0..n: lines representing each year's monthly Usage (Kw-h) Bonus points: instead of a line for each year, each month would have a high-low-close (HLC) bar; 'close' would be replaced by the average second Y axis and HLC bar that represents cost/month Questions: Can this be done without a Pivot table? Do I need to have the Year and Month column or can Excel automatically determine this? Current chart:

  Read the article

< Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >