Search Results

Search found 22447 results on 898 pages for 'message bus'.

Page 80/898 | < Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >

• Video memory buswidth vs video memory Bandwidth

  - by Mixxiphoid

  My current video card (9600GT) is dying and I'm searching for a new video card. Between acquiring my current one and now, I got a lot more knowledge about hardware and I want to use that to pick my new card. So I decided to not just buy some popular card blindly, but to search for a card able to handle my hardware requirements. I searched the specs at the NVidia site for the GT640 and was confused by the memory section and some questions raised. My current card's memory bus width is 256bit and has 1GB of memory. I checked Google about the importance of bus width. And all the links basically said the same 'The higher the number the more potential simultaneously traffic can be transferred'. This was already clear to me, yet there are currently a lot of new cards which are considered better than my current one with a lower bus width. To go in more detail about my question I copied the memory info from the NVidia site: GT 640 GT640 GDDR5 Memory Specs: Memory Clock 1.8 Gbps 5.0 Gbps Standard Memory Config 2048 MB 1024 MB Memory Interface DDR3 GDDR5 Memory Interface Width 128-bit 64-bit Memory Bandwidth (GB/sec) 28.5 40.0 What puzzled me is that the Memory Bandwidth seems to me the most important part, yet the lower bus width has the higher 'performance'. Is this due to the fact the memory interface is GDDR5 and is therefore able to have a higher memory clock speed (5Gbps)? If I am to buy a new video card, should I check the bus width? Memory clock? Bandwith? Amount of memory? My current card ahs 1GB memory, so I was searching for a 2GB memory card, but now I'm not so sure any more whether that is really 'better'. My main question: To me it seems that memory performance is made up by the combination of bus width and frequency. Is this true? If yes, why are there so many sites telling me I need to get a card with a high bus width? If no, then what IS important when it goes about memory performance on a video card. NOTE: The memory bandwidth is (almost) never displayed on vendor sites. How can I determine which card is better without knowing the bandwith?

  Read the article

• usb_modeswitch not switching

  - by deniz

  After I upgraded from kernel 2.6.18 to 3.5.3 modeswitch started not to work for me. Although lsusb shows my usb modem, usb_modeswitch does not switch it. My system information is like below. I ran lsusb, dmesg, usb-devices and usb_modeswitch their output is like below. usb_modeswitch instead of switching my modem it says "No devices in default mode found. Nothing to do. Bye.". Can you offer a solution? Kernel: Linux 3.5.3 usb_modeswitch: 1.2.3-1 usb_modeswitch-data: 20120120-1 usbutils: 006-1 libusb: 1.0.8-0.1 root@localhost$ lsusb Bus 002 Device 029: ID 12d1:1446 Huawei Technologies Co., Ltd. root@localhost$ dmesg [70112.477080] usb 2-1.4: new high-speed USB device number 30 using ehci_hcd [70112.567757] scsi49 : usb-storage 2-1.4:1.0 [70112.567842] scsi50 : usb-storage 2-1.4:1.1 [70113.571433] scsi 49:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 [70113.572304] scsi 50:0:0:0: Direct-Access HUAWEI TF CARD Storage PQ: 0 ANSI: 2 [70113.574169] sr0: scsi-1 drive [70113.574223] sr 49:0:0:0: Attached scsi CD-ROM sr0 [70113.574250] sr 49:0:0:0: Attached scsi generic sg1 type 5 [70113.574350] sd 50:0:0:0: Attached scsi generic sg2 type 0 [70113.577173] sd 50:0:0:0: [sdb] Attached SCSI removable disk root@localhost$ usb-devices T: Bus=02 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#= 30 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=12d1 ProdID=1446 Rev=00.00 S: Manufacturer=Huawei Technologies S: Product=HUAWEI Mobile C: #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage root@localhost$ cat /etc/usb_modeswitch.d/12d1\:1446 # Huawei, newer modems TargetVendor= 0x12d1 TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" MessageContent="55534243123456780000000000000011062000000100000000000000000000" root@localhost$ usb_modeswitch -c /etc/usb_modeswitch.d/12d1:1446 -v 12d1 -p 1446 -W * usb_modeswitch: handle USB devices with multiple modes * Version 1.2.3 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above) ! PLEASE REPORT NEW CONFIGURATIONS ! DefaultVendor= 0x12d1 DefaultProduct= 0x1446 TargetVendor= 0x12d1 TargetProduct= not set TargetClass= not set TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243123456780000000000000011062000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set InquireDevice enabled (default) Success check disabled System integration mode disabled usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Skipping non bus directory devices usb_os_find_busses: Skipping non bus directory drivers usb_os_find_busses: Skipping non bus directory uevent usb_os_find_busses: Skipping non bus directory drivers_probe usb_os_find_busses: Skipping non bus directory drivers_autoprobe Looking for target devices ... No devices in target mode or class found Looking for default devices ... No devices in default mode found. Nothing to do. Bye. Thanks in advance.

  Read the article

• can I disable the "(Type e to repeat macro)" message in emacs?

  - by lindes

  Hi there, So, I've finally made the plunge, and have gotten to the state where I'm quite happy to have switched from vi and vim to emacs... I've been putting stuff in my .emacs file, learning how to evaluate things (not to mention becoming familiar with movement commands), etc. etc. etc. And now I have a problem with a require line in my .emacs file (a require statement*), which bombs out when I launch emacs (and generally fails to work). So, this lead me to the following situation: In the process of trying to debug the above situation, one of the steps I did was to open the file I was trying to require, and evaluate it bit by bit, using C-M-f and C-x C-e (and later just M-x eval-buffer), which all worked fine. But along the way of the section-by-section, I got tired of typing all those, and so I recorded a keyboard macro... C-x ( C-M-f C-x C-e C-x ) and then C-x e... which gave me a message in the minibuffer (I think I'm using the right name), saying (Type e to repeat macro). Which meant I could no longer see the resultant value of the evaluation of each section of code... which, while not critical in this case, I was liking having. Which leads me to the actual question: Is there a way to disable that message, and/or to cause the minibuffer to show multiple lines at once? I know about the *Messages* buffer, and that could have helped, I'm just wondering if there's a way to either disable that message, or otherwise make it coexist with other messages. Any suggestions? Thanks! lindes * - the problem at hand, which is not really my question, is that (require 'ruby-mode/ruby-mode) fails, even though emacs is definitely and successfully (per system call tracing) opening and reading the ruby-mode.el file. I presume this is because the provide line says just 'ruby-mode. I've found a solution for this, but if anyone can point me to any "best practices", I'd appreciate it.

  Read the article

• php fuel 42000 error

  - by ryanc1256

  I don't get whats wrong. So this is the full error I get... Fuel\Core\Database_Exception [ 42000 ]: SQLSTATE[42000]: Syntax error or access violation: 1064 You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near 'to, from, message, checked) VALUES ('1', 'freddy', 'bob', 'message', '1')' at line 1 with query: "INSERT INTO chatmes (id, to, from, message, checked) VALUES ('1', 'freddy', 'bob', 'message', '1')" and this my php code which is supposably giving me the error <?php define('DOCROOT', __DIR__.DIRECTORY_SEPARATOR); define('APPPATH', realpath('/var/www/vhosts/grubber.co.nz/httpdocs/fuel/app/').DIRECTORY_SEPARATOR); define('PKGPATH', realpath('/var/www/vhosts/grubber.co.nz/httpdocs/fuel/packages/').DIRECTORY_SEPARATOR); define('COREPATH', realpath('/var/www/vhosts/grubber.co.nz/httpdocs/fuel/core/').DIRECTORY_SEPARATOR); require APPPATH.'bootstrap.php'; error_reporting(-1); ini_set('display_errors', 1); $to = $_GET['to']; $from = $_GET['from']; $message = $_GET['message']; $dquotes = '"'; $squotes = "'"; $message = str_replace($dquotes, "&quot", $message); $message = str_replace($squotes, "&#039", $message); DB::insert('chatmes')->set(array('id' => '1', 'to' => 'freddy', 'from' => 'bob', 'message' => 'message', 'checked' => '1'))->execute(); ?> I dont know what I am doing wrong?? Also the connection im using is PDO At the moment the only line thats giving me a error is, the db update query

  Read the article

• how to edit a text message ( sms ) as it arrives in windows mobile 6 using managed code

  - by x86shadow

  I want to make an application to be installed on two pocket PCs and send Encrypted text messages and receive and decrypt them on the other device. I already made an application that gets special text messages ( starting with !farenc! ) and I know how to Encrypt/Decrypt the messages as well but I don't know how to edit a text message as it's arrive ( for decryption ). please help. thanks in advance and sorry for my bad English using System; using System.Linq; using System.Collections.Generic; using System.ComponentModel; using System.Data; using System.Drawing; using System.Text; using System.Windows.Forms; using Microsoft.WindowsMobile; using Microsoft.WindowsMobile.PocketOutlook; using Microsoft.WindowsMobile.PocketOutlook.MessageInterception; namespace SMSDECRYPT { public partial class Form1 : Form { MessageInterceptor _SMSCatcher = new MessageInterceptor(InterceptionAction.Notify, true); MessageCondition _SMSFilter = new MessageCondition(); public Form1() { InitializeComponent(); _SMSFilter.Property = MessageProperty.Body; _SMSFilter.ComparisonType = MessagePropertyComparisonType.StartsWith; _SMSFilter.CaseSensitive = true; _SMSFilter.ComparisonValue = "!farenc!"; _SMSCatcher.MessageCondition = _SMSFilter; _SMSCatcher.MessageReceived += new MessageInterceptorEventHandler(_SMSCatcher_MessageReceived); } private void Form1_Load(object sender, EventArgs e) { //... } void _SMSCatcher_MessageReceived(object sender, MessageInterceptorEventArgs e) { SmsMessage mySMS = (SmsMessage)e.Message; string sms = mySMS.Body.ToString(); sms = sms.Substring(8); //Decryption //... //Update the received message and replace it with the decrypted text //!!!HELP!!! } } }

  Read the article

• google chrome extension update text after response callback

  - by Jerome

  I am writing a Google Chrome extension. I have reached the stage where I can pass messages back and forth readily but I am running into trouble with using the response callback. My background page opens a message page and then the message page requests more information from background. When the message page receives the response I want to replace some of the standard text on the message page with custom text based on the response. Here is the code: chrome.extension.sendRequest({cmd: "sendKeyWords"}, function(response) { keyWordList=response.keyWordsFound; var keyWords=""; for (var i = 0; i FIRST QUESTION: This all seems to work fine but the text on the page doesn't change. I am almost certainly because the callback completes after the page is finished loading and the rest of the code finishes before the callback completes, too. How do I update the page with the new text? Can I listen for the callback to complete or something like that? SECOND QUESTION: The procedure I am pursuing first opens the message page and then the message page requests the keyword list from background. Since I always want the keyword list, it makes more sense to just send it when I create the tab. Can I do that? Here is the code from background that opens the message page: //when request from detail page to open message page chrome.extension.onRequest.addListener(function(request, sender, sendResponse) { if(request.cmd == "openMessage") { console.log("Received Request to Open Message, Profile Score: "+request.keyWordsFound.length); keyWordList=request.keyWordsFound; chrome.tabs.create({url: request.url}, function(tab){ msgTabId=tab.id; //needed to determine if message tab has later been closed chrome.tabs.executeScript(tab.id, {file: "message.js"}); }); console.log("Opening Message"); } });

  Read the article

• How can I edit an incoming text message (sms) as it arrives in windows mobile 6 using managed code

  - by x86shadow

  I want to make an application for pocket PCs to send and receive Encrypted text messages. I have already made an application that gets special text messages ( starting with !farenc! ) and I know how to Encrypt/Decrypt the messages as well. The problem is that I don't know how to edit a text message after it's arrived (for decryption). See code below for more info. using System; using System.Linq; using System.Collections.Generic; using System.ComponentModel; using System.Data; using System.Drawing; using System.Text; using System.Windows.Forms; using Microsoft.WindowsMobile; using Microsoft.WindowsMobile.PocketOutlook; using Microsoft.WindowsMobile.PocketOutlook.MessageInterception; namespace SMSDECRYPT { public partial class Form1 : Form { MessageInterceptor _SMSCatcher = new MessageInterceptor(InterceptionAction.Notify, true); MessageCondition _SMSFilter = new MessageCondition(); public Form1() { InitializeComponent(); _SMSFilter.Property = MessageProperty.Body; _SMSFilter.ComparisonType = MessagePropertyComparisonType.StartsWith; _SMSFilter.CaseSensitive = true; _SMSFilter.ComparisonValue = "!farenc!"; _SMSCatcher.MessageCondition = _SMSFilter; _SMSCatcher.MessageReceived += new MessageInterceptorEventHandler(_SMSCatcher_MessageReceived); } private void Form1_Load(object sender, EventArgs e) { //... } void _SMSCatcher_MessageReceived(object sender, MessageInterceptorEventArgs e) { SmsMessage mySMS = (SmsMessage)e.Message; string sms = mySMS.Body.ToString(); sms = sms.Substring(8); //Decryption //... //Update the received message and replace it with the decrypted text //!!!HELP!!! } } }

  Read the article

• What is the best practice for including jQuery ext functions?

  - by Metropolis

  Hey everyone, Currently I have a file that I named JQuery.ext.js which I am including in all of my pages. Inside this file I have numerous functions that do things like the following, (function($) { /** * Checks to see is the value inside ele is blank * @param message string The message that needs to be displayed if the element is blank * @return bool */ $.fn.isEmpty = function(message) { var b_IsEmpty = false; //Loop through all elements this.each(function() { //Check to see if an empty value is found if($(this).val().length <= 0) { //If message is not blank if(message) { alert(message); $(this).focus().select(); } b_IsEmpty = true; return false; } return true; }); //Return false if the evaluation failed, otherwise return the jquery object so we can reuse it return (b_IsEmpty) ? true : false; }; /** * Checks to see if the value inside ele is numbers only * @param message string The message that needs to be displayed if the element is not numeric * @return bool */ $.fn.isNumeric = function(message) { var expression = /^[0-9]+$/; var b_IsNumeric = true; //Loop through elements checking each one this.each( function() { //Check to see if this value is not numeric if(!$(this).val().match(expression) && $(this).val().length > 0) { //If message is not blank if(message) { alert(message); $(this).focus().select(); } b_IsNumeric = false; } return b_IsNumeric; }); return b_IsNumeric; }; })(jQuery); Is there another way to do this? or is this the way most people do it? Thanks for any help, Metropolis

  Read the article

• Ruby On Rails - Contact form not sending email via localhost

  - by anonymousxxx

  similar problem Rails contact form not working guides: https://github.com/thomasklemm/email_form_rails rails 3.2.x app\models\message.rb class Message include ActiveAttr::Model include ActiveModel::Validations attribute :name attribute :email attribute :subject attribute :body attr_accessible :name, :email, :subject, :body validates_presence_of :name validates_presence_of :email validates :email, email_format: { message: "is not looking like a valid email address"} validates_presence_of :subject validates_length_of :body, maximum: 500 end app\mailers\contact_form.rb class ContactForm < ActionMailer::Base default from: "[email protected]" default to: "[email protected]" def email_form(message) @message = message mail subject: "#{message.subject} #{message.name}" mail body: "#{message.body}" end end development.rb config.action_mailer.delivery_method = :smtp config.action_mailer.perform_deliveries = true config.action_mailer.smtp_settings = { :address => "smtp.gmail.com", :port => 587, :domain => "mydomain.com", :user_name => "[email protected]", :password => "mypassword", :authentication => :plain, :enable_starttls_auto => true } config.action_mailer.default_url_options = { :host => "localhost:3000" } output in command Started POST "/email" for 127.0.0.1 at 2012-09-04 22:10:40 +0700 Processing by HomeController#send_email_form as HTML Parameters: {"utf8"="v", "authenticity_token"="w39BLqCrjTMm4RRi/Sm5hZoEpcw46 npyRy/RS0h48x0=", "message"={"name"="anonymousxxx", "email"="[email protected]", "subject"="Test", "body"="send email"}, "commit"="Create Message"} Redirected to localhost:3000/home/contact Completed 302 Found in 1ms (ActiveRecord: 0.0ms) but email (message) no receive my email,..

  Read the article

• What is the WORST commit message you have ever authored?

  - by rpkelly

  I mean, we've all done it, making some changes and the checking them in with messages such "as made some changes" or "fixed a bug." Messages so inane, so pointless, you might as well have written "magical fun bus" in their place (of this, I am guilty), as it would be, perhaps, more descriptive. I ask you then, what is the most pointless, most off topic, strangest, or just WORST commit message you have ever authored?

  Read the article

• Delphi: EReadError with message ‘Property PageNr does Not Exist’.

  - by lyborko

  Hi, I get SOMETIMES error message: EReadError with message 'Property PageNr does Not exist', when I try to run my own project. I am really desperate, because I see simply nothing what is the cause. The devilish is that it comes up sometimes but often. It concerns of my own component TPage. Here is declaration TPage = class(TCustomControl) // private FPaperHeight, FPaperWidth:Integer; FPaperBrush:TBrush; FPaperSize:TPaperSize; FPaperOrientation:TPaperOrientation; FPDFDocument: TPDFDocument; FPageNr:integer; procedure PaintBasicLayout; procedure PaintInterior; procedure SetPapersize(Value: TPapersize); procedure SetPaperHeight(Value: Integer); procedure SetPaperWidth(Value: Integer); procedure SetPaperOrientation(value:TPaperOrientation); procedure SetPaperBrush(Value:TBrush); procedure SetPageNr(Value:Integer); protected procedure CreateParams(var Params:TCreateParams); override; procedure AdjustClientRect(var Rect: TRect); override; public constructor Create(AOwner: TComponent);override; destructor Destroy;override; // function GetChildOwner:TComponent; override; procedure DrawControl(X,Y :integer; Dx,Dy:Double; Ctrl:TControl;NewCanvas:TCanvas); // procedure GetChildren(Proc:TGetChildProc; Root:TComponent); override; procedure Loaded; override; procedure MouseDown(Button: TMouseButton; Shift: TShiftState; X, Y: Integer); override; procedure Paint; override; procedure PrintOnCanvas(X,Y:integer; rX,rY:Double; ACanvas:TCanvas); procedure PrintOnPDFCanvas(X,Y:integer); procedure PrintOnPrinterCanvas(X,Y:integer); procedure Resize; override; procedure SetPrintKind(APrintKind:TPrintKind; APrintGroupindex:Integer); published property PageNr:integer read FPageNr write SetPageNr; property PaperBrush: TBrush read FPaperBrush write SetPaperBrush; property PaperHeight: integer read FPaperHeight write SetPaperHeight; property PaperWidth: integer read FPaperWidth write SetPaperWidth; property PaperSize: TPaperSize read FPaperSize write SetPaperSize; property PaperOrientation:TPaperOrientation read FPaperOrientation write SetPaperOrientation; property PDFDocument:TPDFDocument read FPDFDocument write FPDFDocument; property TabOrder; end; I thoroughly read the similar topic depicted here: Delphi: EReadError with message 'Property Persistence does Not exist' But here it is my own source code. No third party. Interesting: when I delete PageNr property in my dfm file (unit1.dfm), then pops up : EReadError with message 'Property PaperHeight does Not exist'. when I delete PaperHeight then it will claim PaperWidth and so on... Here is piece of dfm file: object pg1: TPage Left = 128 Top = 144 Width = 798 Height = 1127 PageNr = 0 PaperHeight = 1123 PaperWidth = 794 PaperSize = psA4 PaperOrientation = poPortrait TabOrder = 0 object bscshp4: TBasicShape Left = 112 Top = 64 Width = 105 Height = 105 PrintKind = pkNormal PrintGroupIndex = 0 Zooming = 100 Transparent = False Repeating = False PageRepeatOffset = 1 ShapeStyle = ssVertical LinePosition = 2 end object bscshp5: TBasicShape Left = 288 Top = 24 Width = 105 Height = 105 PrintKind = pkNormal PrintGroupIndex = 0 Zooming = 100 Transparent = False What the hell happens ??????? I have never seen that. I compiled the unit several times... Encoutered no problem. Maybe the cause is beyond this. I feel completely powerless.

  Read the article

• Exchange 2010: Receiving "You can't send a message on behalf of this user..." error when trying to configure delegate access

  - by Beaming Mel-Bin

  I am trying to give someone (John Doe) delegate access to another account (Jane Doe) in our test environment. However, I receive the following error from Exchange: *Subject:* Undeliverable: You have been designated as a delegate for Jane Dow *To:* Jane Dow Delivery has failed to these recipients or groups: John Doe You can't send a message on behalf of this user unless you have permission to do so. Please make sure you're sending on behalf of the correct sender, or request the necessary permission. If the problem continues, please contact your helpdesk. Diagnostic information for administrators: Generating server: /O=UNIONCO/OU=EXCHANGE ADMINISTRATIVE GROUP (FYD132341234)/CN=RECIPIENTS/CN=jdoe #MSEXCH:MSExchangeIS:/DC=local/DC=unionco:MAILBOX-1[578:0x000004DC:0x0000001D] #EX# Can someone help me troubleshoot this?

  Read the article

• What's the largest message size modern email systems generally support?

  - by Phil Hollenback

  I know that Yahoo and Google mail support 25MB email attachments. I have an idea from somewhere that 10MB email messages are generally supported by modern email systems. So if I'm sending an email between two arbitrary users on the internet, what's the safe upper bound on message size? 1MB? 10MB? 25MB? I know that one answer is 'don't send big emails, use some sort of drop box'. I'm looking for a guideline if you are limited to only using regular smtp email.

  Read the article

• How to tell httpd to preserve the proxied error message?

  - by ZNK - M

  I have an httpd server proxying the requests to 2 different tomcat servers. One of my server handles the authentication and returns a specific http error code 521 when the user already have a running session. My issue is httpd automatically maps this 521 error code to a 500 (internal server error) and then my client can not handle it properly. I have tried to disable ProxyErrorOverride, to remove the /error/HTTP_INTERNAL_SERVER_ERROR.html.var but it does not changes anything. How can I ask httpd to not change anything to the proxied message? <IfModule proxy_module> ProxyPass /context1 http://127.0.0.1:8001/context1 ProxyPass /context2 http://127.0.0.1:8002/context2 ProxyPreserveHost Off ProxyErrorOverride Off </IfModule> Thanks in advance httpd 2.2.22 (Win32) mod_ssl tomcat 7.25 windows 7 64-bits

  Read the article

• Is there a way to set up message moderation in Exchange 2007?

  - by Nate Pinchot

  Is there a way to get a feature in Exchange 2007 similar to message moderation in Exchange 2010 through the use of third party tools or otherwise? I've Googled things like "exchange 2007 outbound email approval" to no avail. We are working on getting Exchange 2010 implemented but I need an interim solution if at all possible. The reason for this is from a customer service perspective. I am willing to use a small process to be a smart host if needed. I would appreciate any suggestions or advice. Edit: My apologies, I should have been more clear that I am trying to moderate/approve outgoing email from certain users, not moderate/approve email sent to a distribution group.

  Read the article

• How do I get rid of the Cisco CP one-time user message on a Cisco 2901 router?

  - by user65712

  I get this message on a new 2901 Cisco router: Cisco Configuration Professional (Cisco CP) is installed on this device and it provides the default username "cisco" for one-time use. If you have already used the username "cisco" to login to the router and your IOS image supports the "one-time" user option, then this username has already expired. You will not be able to login to the router with this username after you exit this session. It is strongly suggested that you create a new username with a privilege level of 15 using the following command. username <myuser> privilege 15 secret 0 <mypassword> Replace and with the username and password you want to use. It appears every time I login and everytime I show run. I already set up my username. How do I turn it off?

  Read the article

• I tried installing Ubuntu 10.04 and I got this message - any ideas on what to do?

  - by vette982

  No root file system defined. Please correct this from the partition menu. This message shows up when I first boot into Ubuntu after the installation. I installed it by mounting the ISO with Daemon Tools, and I just did the default Wubi installation. I keep reading everywhere that I need to choose my installation directory, but I don't get any option to do that. These are all the options I get for installation directory. I have a C and D partition on my drive, and I tried installing it on both and no luck either way. Any ideas?

  Read the article

• I tried installing Ubuntu 10.04 and I got this message - any ideas on what to do?

  - by user41926

  No root file system defined. Please correct this from the partition menu. This message shows up when I first boot into Ubuntu after the installation. I installed it by mounting the ISO with Daemon Tools, and I just did the default Wubi installation. I keep reading everywhere that I need to choose my installation directory, but I don't get any option to do that. These are all the options I get for installation directory. I have a C and D partition on my drive, and I tried installing it on both and no luck either way. Any ideas?

  Read the article

• putty 0.61 : why do I see "Access Denied" message after I enter my login id?

  - by anjanbacchu

  I use putty to login to my RHEL 5.3 server. I'm prompted to enter my login as "login as " and I enter my login Id. as soon as I press ENTER, I see a "Access Denied" message following which I'm prompted with password. I successfully enter password and I'm through -- no problems. I tried the same with putty 0.60(as opposed to above putty 0.61) but in this version, I don't get any "access denied" error. What should I make of this ? Is putty 0.61 version buggy ? P.S : If I login using ssh.exe(from cygwin), then I'm fine -- I don't get any "access denied" errors. Thank you,

  Read the article

• Outlook or OWA: How can I convert an e-mail message to a draft?

  - by Beaming Mel-Bin

  There's an option in Thunderbird called Edit as new... which converts a message to a draft. I am looking for something similar in Exchange. Reasoning: We migrated old e-mail of a user from an IMAP server to Exchange. The user had many drafts saved. According to exchange though, the messages are not drafts anymore. My hunch is that, if we find a similar procedure as Thunderbird's Edit as new..., that should do the trick.

  Read the article

• Mulitple lines in make

  - by Navi

  I am trying to store a multiline string in a variable in make var=$(shell cat <<End-of-message \ -------------------------------------\ This is line 1 of the message.\ This is line 2 of the message.\ This is line 3 of the message.\ This is line 4 of the message.\ This is the last line of the message.\ -------------------------------------\ End-of-message) printit: @echo ${var} This doesn't work, so I am wondering if this is possible at all. I need to preserve the newlines here and shell is converting them in spaces. Any suggestions?

  Read the article

• closing MQ connection

  - by OakvilleWork

  Good afternoon, I wrote a project to Get Park Queue Info from the IBM MQ, it has producing an error when attempting to close the connection though. It is written in java. Under application in Event Viewer on the MQ machine it displays two errors. They are: “Channel program ended abnormally. Channel program ‘system.def.surconn’ ended abnormally. Look at previous error messages for channel program ‘system.def.surconn’ in the error files to determine the cause of the failure. The other message states: “Error on receive from host rnanaj (10.10.12.34) An error occurred receiving data from rnanaj (10.10.12.34) over tcp/ip. This may be due to a communications failure. The return code from tcp/ip recv() call was 10054 (X’2746’). Record these values.” This must be something how I try to connect or close the connection, below I have my code to connect and close, any ideas?? Connect: _logger.info("Start"); File outputFile = new File(System.getProperty("PROJECT_HOME"), "run/" + this.getClass().getSimpleName() + "." + System.getProperty("qmgr") + ".txt"); FileUtils.mkdirs(outputFile.getParentFile()); Connection jmsConn = null; Session jmsSession = null; QueueBrowser queueBrowser = null; BufferedWriter commandsBw = null; try { // get queue connection MQConnectionFactory MQConn = new MQConnectionFactory(); MQConn.setHostName(System.getProperty("host")); MQConn.setPort(Integer.valueOf(System.getProperty("port"))); MQConn.setQueueManager(System.getProperty("qmgr")); MQConn.setChannel("SYSTEM.DEF.SVRCONN"); MQConn.setTransportType(JMSC.MQJMS_TP_CLIENT_MQ_TCPIP); jmsConn = (Connection) MQConn.createConnection(); jmsSession = jmsConn.createSession(false, Session.AUTO_ACKNOWLEDGE); Queue jmsQueue = jmsSession.createQueue("PARK"); // browse thru messages queueBrowser = jmsSession.createBrowser(jmsQueue); Enumeration msgEnum = queueBrowser.getEnumeration(); commandsBw = new BufferedWriter(new FileWriter(outputFile)); // String line = "DateTime\tMsgID\tOrigMsgID\tCorrelationID\tComputerName\tSubsystem\tDispatcherName\tProcessor\tJobID\tErrorMsg"; commandsBw.write(line); commandsBw.newLine(); while (msgEnum.hasMoreElements()) { Message message = (Message) msgEnum.nextElement(); line = dateFormatter.format(new Date(message.getJMSTimestamp())) + "\t" + message.getJMSMessageID() + "\t" + message.getStringProperty("pkd_orig_jms_msg_id") + "\t" + message.getJMSCorrelationID() + "\t" + message.getStringProperty("pkd_computer_name") + "\t" + message.getStringProperty("pkd_subsystem") + "\t" + message.getStringProperty("pkd_dispatcher_name") + "\t" + message.getStringProperty("pkd_processor") + "\t" + message.getStringProperty("pkd_job_id") + "\t" + message.getStringProperty("pkd_sysex_msg"); _logger.info(line); commandsBw.write(line); commandsBw.newLine(); } } Close: finally { IO.close(commandsBw); if (queueBrowser != null) { try { queueBrowser.close();} catch (Exception ignore) {}} if (jmsSession != null) { try { jmsSession.close();} catch (Exception ignore) {}} if (jmsConn != null) { try { jmsConn.stop();} catch (Exception ignore) {}} }

  Read the article

• Having trouble understanding some code (Ruby on Rails)

  - by user284194

  I posted a question awhile ago asking how I could limit the rate at which a form could be submitted from a rails application. I was helped by a very patient user and their solution works great. The code was for my comments controller, and now I find myself wanting to add this functionality to another controller, my Messages controller. I immediately tried reusing the working code from the comments controller but I couldn't get it to work. Instead of asking for the working code, could someone please help me understand my working comment controller code? class CommentsController < ApplicationController #... before_filter :post_check def record_post_time cookies[:last_post_at] = Time.now.to_i end def last_post_time Time.at((cookies[:last_post_at].to_i rescue 0)) end MIN_POST_TIME = 2.minutes def post_check return true if (Time.now - last_post_time) > MIN_POST_TIME flash[:warning] = "You are trying to reply too fast." @message = Message.find(params[:message_id]) redirect_to(@message) return false end #... def create @message = Message.find(params[:message_id]) @comment = @message.comments.build(params[:comment]) if @comment.save record_post_time flash[:notice] = "Replied to \"#{@message.title}\"" redirect_to(@message) else render :action => "new" end end def update @message = Message.find(params[:message_id]) @comment = Comment.find(params[:id]) if @comment.update_attributes(params[:comment]) record_post_time redirect_to post_comment_url(@message, @comment) else render :action => "edit" end end #... end My Messages controller is pretty much a standard rails generated controller with a few before filters and associated private methods for DRYing up the code and a redirect for non existent pages. I'll explain how much of the code I understand. When a comment is created, a cookie is created with a last_post_time value. If they try to post another comment, the cookie is checked if the last one was made in the last two minutes. If it was a flash warning is displayed and no comment is recorded. What I don't really understand is how the post_check method works and how I can adapt it for my simpler posts controller. I thought I could reuse all the code in the message controller with the exception of the line: @message = Message.find(params[:message_id]) # (don't need the redirect code) in the post_check method. But it trips up on the "record_post_time" in the create action/method. I really want to understand this. Can someone explain why this doesn't work? I greatly appreciate you reading my lengthy question.

  Read the article

• BizTalk host throttling &ndash; Singleton pattern and High database size

  - by S.E.R.

  Originally posted on: http://geekswithblogs.net/SERivas/archive/2013/06/30/biztalk-host-throttling-ndash-singleton-pattern-and-high-database-size.aspxI have worked for some days around the singleton pattern (for those unfamiliar with it, read this post by Victor Fehlberg) and have come across a few very interesting posts, among which one dealt with performance issues (here, also by Victor Fehlberg). Simply put: if you have an orchestration which implements the singleton pattern, then performances will continuously decrease as the orchestration receives and consumes messages, and that behavior is more obvious when the orchestration never ends (ie : it keeps looping and never terminates or completes). As I experienced the same kind of problem (actually I was alerted by SCOM, which told me that the host was being throttled because of High database size), I thought it would be a good idea to dig a little bit a see what happens deep inside BizTalk and thus understand the reasons for this behavior. NOTE: in this article, I will focus on this High database size throttling condition. I will try and work on the other conditions in some not too distant future… Test conditions The singleton orchestration For the purpose of this study, I have created the following orchestration, which is a very basic implementation of a singleton that piles up incoming messages, then does something else when a certain timeout has been reached without receiving another message: Throttling settings I have two distinct hosts : one that hosts the receive port (basic FILE port) : Ports_ReceiveHostone that hosts the orchestration : ProcessingHost In order to emphasize the throttling mechanism, I have modified the throttling settings for each of these hosts are as follows (all other parameters are set to the default value): [Throttling thresholds] Message count in database: 500 (default value : 50000) Evolution of performance counters when submitting messages Since we are investigating the High database size throttling condition, here are the performance counter that we should take a look at (all of them are in the BizTalk:Message Agent performance object): Database sizeHigh database sizeMessage delivery throttling stateMessage publishing throttling stateMessage delivery delay (ms)Message publishing delay (ms)Message delivery throttling state durationMessage publishing throttling state duration (If you are not used to Perfmon, I strongly recommend that you start using it right now: it is a wonderful tool that allows you to open the hood and see what is going on inside BizTalk – and other systems) Database size It is quite obvious that we will start by watching the database size and high database size counters, just to see when the first reaches the configured threshold (500) and when the second rings the alarm. NOTE : During this test I submitted 600 messages, one message at a time every 10ms to see the evolution of the counters we have previously selected. It might not show very well on this screenshot, but here is what happened: From 15:46:50 to 15:47:50, the database size for the Ports_ReceiveHost host (blue line) kept growing until it reached a maximum of 504.At 15:47:50, the high database size alert fires At first I was surprised by this result: why is it the database size of the receiving host that keeps growing since it is the processing host that piles up messages? Actually, it makes total sense. This counter measures the size of the database queue that is being filled by the host, not consumed. Therefore, the high database size alert is raised on the host that fills the queue: Ports_ReceiveHost. More information is available on the Public MPWiki page. Now, looking at the Message publishing throttling state for the receiving host (green line), we can see that a throttling condition has been reached at 15:47:50: We can also see that the Message publishing delay(ms) (blue line) has begun growing slowly from this point. All of this explains why performances keep decreasing when a singleton keeps processing new messages: the database size grows and when it has exceeded the Message count in database threshold, the host is throttled and the publishing delay keeps increasing. Digging further So, what happens to the database queue then? Is it flushed some day or does it keep growing and growing indefinitely? The real question being: will the host be throttled forever because of this singleton? To answer this question, I set the Message count in database threshold to 20 (this value is very low in order not to wait for too long, otherwise I certainly would have fallen asleep in front of my screen) and I submitted 30 messages. The test was started at 18:26. At 18:56 (ie : exactly 30min later) the throttling was stopped and the database size was divided by 2. 30 min later again, the database size had dropped to almost zero: I guess I’ll have to find some documentation and do some more testing before I sort this out! My guess is that some maintenance job is at work here, though I cannot tell which one Digging even further If we take a look at the Message delivery throttling state counter for the processing host, we can see that this host was also throttled during the submission of the 600 documents: The value for the counter was 1, meaning that Message delivery incoming rate for the host instance exceeds the Message delivery outgoing rate * the specified Rate overdrive factor (percent) value. We will see this another day… :) A last word Let’s end this article with a warning: DO NOT CHANGE THE THROTTLING SETTINGS LIGHTLY! The temptation can be great to just bypass throttling by setting very high values for each parameter (or zero in some cases, which simply disables throttling). Nevertheless, always keep in mind that this mechanism is here for a very good reason: prevent your BizTalk infrastructure from exploding!! So whatever you do with those settings, do a lot of testing and benchmarking!

  Read the article

• Wireless card power management

  - by penner

  I have noticed that when my computer in plugged in, the wireless strength increases. I'm assuming this is to do with power management. Is there a way to disable Wireless Power Management? I have found a few blog posts that show hacks to disable this but what is best practice here? Should there not be an option via the power menu that lets you toggle this? EDIT -- FILES AND LOGS AS REQUESTED /var/log/kern.log Jul 11 11:45:27 CoolBreeze kernel: [ 6.528052] postgres (1308): /proc/1308/oom_adj is deprecated, please use /proc/1308/oom_score_adj instead. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532080] [fglrx] Gart USWC size:1280 M. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532084] [fglrx] Gart cacheable size:508 M. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532091] [fglrx] Reserved FB block: Shared offset:0, size:1000000 Jul 11 11:45:27 CoolBreeze kernel: [ 6.532094] [fglrx] Reserved FB block: Unshared offset:f8fd000, size:403000 Jul 11 11:45:27 CoolBreeze kernel: [ 6.532098] [fglrx] Reserved FB block: Unshared offset:3fff4000, size:c000 Jul 11 11:45:38 CoolBreeze kernel: [ 17.423743] eth1: no IPv6 routers present Jul 11 11:46:37 CoolBreeze kernel: [ 75.836426] warning: `proftpd' uses 32-bit capabilities (legacy support in use) Jul 11 11:46:37 CoolBreeze kernel: [ 75.884215] init: plymouth-stop pre-start process (2922) terminated with status 1 Jul 11 11:54:25 CoolBreeze kernel: [ 543.679614] eth1: no IPv6 routers present dmesg [ 1.411959] ACPI: Power Button [PWRB] [ 1.412046] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 [ 1.412054] ACPI: Sleep Button [SLPB] [ 1.412150] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2 [ 1.412765] ACPI: Lid Switch [LID0] [ 1.412866] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 1.412874] ACPI: Power Button [PWRF] [ 1.412996] ACPI: Fan [FAN0] (off) [ 1.413068] ACPI: Fan [FAN1] (off) [ 1.419493] thermal LNXTHERM:00: registered as thermal_zone0 [ 1.419498] ACPI: Thermal Zone [TZ00] (27 C) [ 1.421913] thermal LNXTHERM:01: registered as thermal_zone1 [ 1.421918] ACPI: Thermal Zone [TZ01] (61 C) [ 1.421971] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 1.421986] ACPI: Battery Slot [BAT0] (battery present) [ 1.422062] ERST: Table is not found! [ 1.422067] GHES: HEST is not enabled! [ 1.422158] isapnp: Scanning for PnP cards... [ 1.422242] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 1.434620] ACPI: Battery Slot [BAT0] (battery present) [ 1.736355] Freeing initrd memory: 14352k freed [ 1.777846] isapnp: No Plug & Play device found [ 1.963650] Linux agpgart interface v0.103 [ 1.967148] brd: module loaded [ 1.968866] loop: module loaded [ 1.969134] ahci 0000:00:1f.2: version 3.0 [ 1.969154] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.969226] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X [ 1.969277] ahci: SSS flag set, parallel bus scan disabled [ 1.969320] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x23 impl SATA mode [ 1.969329] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems sxs apst [ 1.969338] ahci 0000:00:1f.2: setting latency timer to 64 [ 1.983340] scsi0 : ahci [ 1.983515] scsi1 : ahci [ 1.983670] scsi2 : ahci [ 1.983829] scsi3 : ahci [ 1.983985] scsi4 : ahci [ 1.984145] scsi5 : ahci [ 1.984270] ata1: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005100 irq 45 [ 1.984277] ata2: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005180 irq 45 [ 1.984282] ata3: DUMMY [ 1.984285] ata4: DUMMY [ 1.984288] ata5: DUMMY [ 1.984292] ata6: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005380 irq 45 [ 1.985150] Fixed MDIO Bus: probed [ 1.985192] tun: Universal TUN/TAP device driver, 1.6 [ 1.985196] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 1.985285] PPP generic driver version 2.4.2 [ 1.985472] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.985507] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.985534] ehci_hcd 0000:00:1a.0: setting latency timer to 64 [ 1.985541] ehci_hcd 0000:00:1a.0: EHCI Host Controller [ 1.985626] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 [ 1.985666] ehci_hcd 0000:00:1a.0: debug port 2 [ 1.989663] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported [ 1.989690] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xf1005800 [ 2.002183] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00 [ 2.002447] hub 1-0:1.0: USB hub found [ 2.002455] hub 1-0:1.0: 3 ports detected [ 2.002607] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 2.002633] ehci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.002639] ehci_hcd 0000:00:1d.0: EHCI Host Controller [ 2.002737] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.002775] ehci_hcd 0000:00:1d.0: debug port 2 [ 2.006780] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported [ 2.006806] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xf1005c00 [ 2.022161] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00 [ 2.022401] hub 2-0:1.0: USB hub found [ 2.022409] hub 2-0:1.0: 3 ports detected [ 2.022567] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.022599] uhci_hcd: USB Universal Host Controller Interface driver [ 2.022720] usbcore: registered new interface driver libusual [ 2.022813] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 2.035831] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.035844] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.036096] mousedev: PS/2 mouse device common for all mice [ 2.036710] rtc_cmos 00:07: RTC can wake from S4 [ 2.036881] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0 [ 2.037143] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 2.037503] device-mapper: uevent: version 1.0.3 [ 2.037656] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 2.037725] EISA: Probing bus 0 at eisa.0 [ 2.037729] EISA: Cannot allocate resource for mainboard [ 2.037734] Cannot allocate resource for EISA slot 1 [ 2.037738] Cannot allocate resource for EISA slot 2 [ 2.037741] Cannot allocate resource for EISA slot 3 [ 2.037745] Cannot allocate resource for EISA slot 4 [ 2.037749] Cannot allocate resource for EISA slot 5 [ 2.037753] Cannot allocate resource for EISA slot 6 [ 2.037756] Cannot allocate resource for EISA slot 7 [ 2.037760] Cannot allocate resource for EISA slot 8 [ 2.037764] EISA: Detected 0 cards. [ 2.037782] cpufreq-nforce2: No nForce2 chipset. [ 2.038264] cpuidle: using governor ladder [ 2.039015] cpuidle: using governor menu [ 2.039019] EFI Variables Facility v0.08 2004-May-17 [ 2.040061] TCP cubic registered [ 2.041438] NET: Registered protocol family 10 [ 2.043814] NET: Registered protocol family 17 [ 2.043823] Registering the dns_resolver key type [ 2.044290] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4 [ 2.044336] Using IPI No-Shortcut mode [ 2.045620] PM: Hibernation image not present or could not be loaded. [ 2.045644] registered taskstats version 1 [ 2.073070] Magic number: 4:976:796 [ 2.073415] rtc_cmos 00:07: setting system clock to 2012-07-11 18:45:23 UTC (1342032323) [ 2.076654] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 2.076658] EDD information not available. [ 2.302111] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.302587] ata1.00: ATA-9: M4-CT128M4SSD2, 000F, max UDMA/100 [ 2.302595] ata1.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 2.303143] ata1.00: configured for UDMA/100 [ 2.303453] scsi 0:0:0:0: Direct-Access ATA M4-CT128M4SSD2 000F PQ: 0 ANSI: 5 [ 2.303746] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.303920] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB) [ 2.304213] sd 0:0:0:0: [sda] Write Protect is off [ 2.304225] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.304471] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.306818] sda: sda1 sda2 < sda5 > [ 2.308780] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.318162] Refined TSC clocksource calibration: 1595.999 MHz. [ 2.318169] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 2.318178] Switching to clocksource tsc [ 2.450939] hub 1-1:1.0: USB hub found [ 2.451121] hub 1-1:1.0: 6 ports detected [ 2.561786] usb 2-1: new high-speed USB device number 2 using ehci_hcd [ 2.621757] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.636143] ata2.00: ATAPI: TSSTcorp DVD+/-RW TS-T633C, D800, max UDMA/100 [ 2.636152] ata2.00: applying bridge limits [ 2.649711] ata2.00: configured for UDMA/100 [ 2.653762] scsi 1:0:0:0: CD-ROM TSSTcorp DVD+-RW TS-T633C D800 PQ: 0 ANSI: 5 [ 2.661486] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.661494] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.661890] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 2.662156] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 2.694649] hub 2-1:1.0: USB hub found [ 2.694840] hub 2-1:1.0: 8 ports detected [ 2.765823] usb 1-1.4: new high-speed USB device number 3 using ehci_hcd [ 2.981454] ata6: SATA link down (SStatus 0 SControl 300) [ 2.982597] Freeing unused kernel memory: 740k freed [ 2.983523] Write protecting the kernel text: 5816k [ 2.983808] Write protecting the kernel read-only data: 2376k [ 2.983811] NX-protecting the kernel data: 4424k [ 3.014594] udevd[127]: starting version 175 [ 3.068925] sdhci: Secure Digital Host Controller Interface driver [ 3.068932] sdhci: Copyright(c) Pierre Ossman [ 3.069714] sdhci-pci 0000:09:00.0: SDHCI controller found [1180:e822] (rev 1) [ 3.069742] sdhci-pci 0000:09:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.069786] sdhci-pci 0000:09:00.0: Will use DMA mode even though HW doesn't fully claim to support it. [ 3.069798] sdhci-pci 0000:09:00.0: setting latency timer to 64 [ 3.069816] mmc0: no vmmc regulator found [ 3.069877] Registered led device: mmc0:: [ 3.070946] mmc0: SDHCI controller on PCI [0000:09:00.0] using DMA [ 3.071078] tg3.c:v3.121 (November 2, 2011) [ 3.071252] tg3 0000:0b:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 3.071269] tg3 0000:0b:00.0: setting latency timer to 64 [ 3.071403] firewire_ohci 0000:09:00.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 3.071417] firewire_ohci 0000:09:00.3: setting latency timer to 64 [ 3.078509] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 3.078517] EXT4-fs (sda1): write access will be enabled during recovery [ 3.110417] tg3 0000:0b:00.0: eth0: Tigon3 [partno(BCM95784M) rev 5784100] (PCI Express) MAC address b8:ac:6f:71:02:a6 [ 3.110425] tg3 0000:0b:00.0: eth0: attached PHY is 5784 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0]) [ 3.110431] tg3 0000:0b:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 3.110436] tg3 0000:0b:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit] [ 3.125492] firewire_ohci: Added fw-ohci device 0000:09:00.3, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x11 [ 3.390124] EXT4-fs (sda1): orphan cleanup on readonly fs [ 3.390135] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078710 [ 3.390232] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2363071 [ 3.390327] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078711 [ 3.390350] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078709 [ 3.390367] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078708 [ 3.390384] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078707 [ 3.390401] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078706 [ 3.390417] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078705 [ 3.390435] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078551 [ 3.390452] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078523 [ 3.390470] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078520 [ 3.390487] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7077901 [ 3.390551] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063272 [ 3.390562] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063266 [ 3.390572] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063261 [ 3.390582] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063256 [ 3.390592] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063255 [ 3.390602] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2363072 [ 3.390620] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2360050 [ 3.390698] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 5250064 [ 3.390710] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2365394 [ 3.390728] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2365390 [ 3.390745] EXT4-fs (sda1): 22 orphan inodes deleted [ 3.390748] EXT4-fs (sda1): recovery complete [ 3.397636] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 3.624910] firewire_core: created device fw0: GUID 464fc000110e2661, S400 [ 3.927467] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 3.929965] udevd[400]: starting version 175 [ 3.933581] Adding 6278140k swap on /dev/sda5. Priority:-1 extents:1 across:6278140k SS [ 3.945183] lp: driver loaded but no devices found [ 3.999389] wmi: Mapper loaded [ 4.016696] ite_cir: Auto-detected model: ITE8708 CIR transceiver [ 4.016702] ite_cir: Using model: ITE8708 CIR transceiver [ 4.016706] ite_cir: TX-capable: 1 [ 4.016710] ite_cir: Sample period (ns): 8680 [ 4.016713] ite_cir: TX carrier frequency (Hz): 38000 [ 4.016716] ite_cir: TX duty cycle (%): 33 [ 4.016719] ite_cir: RX low carrier frequency (Hz): 0 [ 4.016722] ite_cir: RX high carrier frequency (Hz): 0 [ 4.025684] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 4.025691] Disabling lock debugging due to kernel taint [ 4.027410] IR NEC protocol handler initialized [ 4.030250] lib80211: common routines for IEEE802.11 drivers [ 4.030257] lib80211_crypt: registered algorithm 'NULL' [ 4.036024] IR RC5(x) protocol handler initialized [ 4.036092] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 4.036188] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X [ 4.036307] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 4.036361] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness [ 4.039006] acpi device:03: registered as cooling_device10 [ 4.039164] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input5 [ 4.039261] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 4.049753] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 4.050201] wl 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 4.050215] wl 0000:05:00.0: setting latency timer to 64 [ 4.052252] Registered IR keymap rc-rc6-mce [ 4.052432] input: ITE8708 CIR transceiver as /devices/virtual/rc/rc0/input6 [ 4.054614] IR RC6 protocol handler initialized [ 4.054787] rc0: ITE8708 CIR transceiver as /devices/virtual/rc/rc0 [ 4.054839] ite_cir: driver has been successfully loaded [ 4.057338] IR JVC protocol handler initialized [ 4.061553] IR Sony protocol handler initialized [ 4.066578] input: MCE IR Keyboard/Mouse (ite-cir) as /devices/virtual/input/input7 [ 4.066724] IR MCE Keyboard/mouse protocol handler initialized [ 4.072580] lirc_dev: IR Remote Control driver registered, major 250 [ 4.073280] rc rc0: lirc_dev: driver ir-lirc-codec (ite-cir) registered at minor = 0 [ 4.073286] IR LIRC bridge handler initialized [ 4.077849] Linux video capture interface: v2.00 [ 4.079402] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:640f) [ 4.085492] EDAC MC: Ver: 2.1.0 [ 4.087138] lib80211_crypt: registered algorithm 'TKIP' [ 4.091027] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [ 4.091733] snd_hda_intel 0000:02:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 4.091826] snd_hda_intel 0000:02:00.1: irq 47 for MSI/MSI-X [ 4.091861] snd_hda_intel 0000:02:00.1: setting latency timer to 64 [ 4.093115] EDAC i7core: Device not found: dev 00.0 PCI ID 8086:2c50 [ 4.112448] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 4.112612] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/0000:02:00.1/sound/card1/input9 [ 4.113311] type=1400 audit(1342032325.540:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=658 comm="apparmor_parser" [ 4.114501] type=1400 audit(1342032325.540:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=658 comm="apparmor_parser" [ 4.115253] type=1400 audit(1342032325.540:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=658 comm="apparmor_parser" [ 4.121870] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input10 [ 4.122096] usbcore: registered new interface driver uvcvideo [ 4.122100] USB Video Class driver (1.1.1) [ 4.128729] [fglrx] Maximum main memory to use for locked dma buffers: 5840 MBytes. [ 4.129678] [fglrx] vendor: 1002 device: 68c0 count: 1 [ 4.131991] [fglrx] ioport: bar 4, base 0x2000, size: 0x100 [ 4.132015] pci 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.132024] pci 0000:02:00.0: setting latency timer to 64 [ 4.133712] [fglrx] Kernel PAT support is enabled [ 4.133747] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 4.162666] eth1: Broadcom BCM4727 802.11 Hybrid Wireless Controller 5.100.82.38 [ 4.184133] device-mapper: multipath: version 1.3.0 loaded [ 4.196660] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 4.279897] input: Dell WMI hotkeys as /devices/virtual/input/input11 [ 4.292402] Bluetooth: Core ver 2.16 [ 4.292449] NET: Registered protocol family 31 [ 4.292454] Bluetooth: HCI device and connection manager initialized [ 4.292459] Bluetooth: HCI socket layer initialized [ 4.292463] Bluetooth: L2CAP socket layer initialized [ 4.292473] Bluetooth: SCO socket layer initialized [ 4.296333] Bluetooth: RFCOMM TTY layer initialized [ 4.296342] Bluetooth: RFCOMM socket layer initialized [ 4.296345] Bluetooth: RFCOMM ver 1.11 [ 4.313586] ppdev: user-space parallel port driver [ 4.316619] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 4.316625] Bluetooth: BNEP filters: protocol multicast [ 4.383980] type=1400 audit(1342032325.812:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=938 comm="apparmor_parser" [ 4.385173] type=1400 audit(1342032325.812:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=938 comm="apparmor_parser" [ 4.425757] init: failsafe main process (898) killed by TERM signal [ 4.477052] type=1400 audit(1342032325.904:7): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1011 comm="apparmor_parser" [ 4.477592] type=1400 audit(1342032325.904:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1010 comm="apparmor_parser" [ 4.478099] type=1400 audit(1342032325.904:9): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=1017 comm="apparmor_parser" [ 4.479233] type=1400 audit(1342032325.904:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1014 comm="apparmor_parser" [ 4.510060] vesafb: mode is 1152x864x32, linelength=4608, pages=0 [ 4.510065] vesafb: scrolling: redraw [ 4.510071] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 4.510084] mtrr: no more MTRRs available [ 4.513081] vesafb: framebuffer at 0xd0000000, mapped to 0xf9400000, using 3904k, total 3904k [ 4.515203] Console: switching to colour frame buffer device 144x54 [ 4.515278] fb0: VESA VGA frame buffer device [ 4.590743] tg3 0000:0b:00.0: irq 48 for MSI/MSI-X [ 4.702009] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.704409] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.978379] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 5.030104] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input12 [ 5.045782] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly. Using workaround [ 5.519573] [fglrx] ATIF platform detected with notification ID: 0x81 [ 6.391466] fglrx_pci 0000:02:00.0: irq 49 for MSI/MSI-X [ 6.393137] [fglrx] Firegl kernel thread PID: 1305 [ 6.393306] [fglrx] Firegl kernel thread PID: 1306 [ 6.393472] [fglrx] Firegl kernel thread PID: 1307 [ 6.393726] [fglrx] IRQ 49 Enabled [ 6.528052] postgres (1308): /proc/1308/oom_adj is deprecated, please use /proc/1308/oom_score_adj instead. [ 6.532080] [fglrx] Gart USWC size:1280 M. [ 6.532084] [fglrx] Gart cacheable size:508 M. [ 6.532091] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 6.532094] [fglrx] Reserved FB block: Unshared offset:f8fd000, size:403000 [ 6.532098] [fglrx] Reserved FB block: Unshared offset:3fff4000, size:c000 [ 17.423743] eth1: no IPv6 routers present [ 75.836426] warning: `proftpd' uses 32-bit capabilities (legacy support in use) [ 75.884215] init: plymouth-stop pre-start process (2922) terminated with status 1 [ 543.679614] eth1: no IPv6 routers present lsmod Module Size Used by kvm_intel 127560 0 kvm 359456 1 kvm_intel joydev 17393 0 vesafb 13516 1 parport_pc 32114 0 bnep 17830 2 ppdev 12849 0 rfcomm 38139 0 bluetooth 158438 10 bnep,rfcomm dell_wmi 12601 0 sparse_keymap 13658 1 dell_wmi binfmt_misc 17292 1 dell_laptop 17767 0 dcdbas 14098 1 dell_laptop dm_multipath 22710 0 fglrx 2909855 143 snd_hda_codec_hdmi 31775 1 psmouse 72919 0 serio_raw 13027 0 i7core_edac 23382 0 lib80211_crypt_tkip 17275 0 edac_core 46858 1 i7core_edac uvcvideo 67203 0 snd_hda_codec_idt 60251 1 videodev 86588 1 uvcvideo ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec ir_mce_kbd_decoder 12681 0 snd_seq_midi 13132 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 snd_rawmidi 25424 1 snd_seq_midi ir_rc6_decoder 12459 0 wl 2646601 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event ir_rc5_decoder 12459 0 video 19068 0 snd_hda_intel 32765 5 snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq snd_hda_codec 109562 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel rc_rc6_mce 12454 0 lib80211 14040 2 lib80211_crypt_tkip,wl snd_hwdep 13276 1 snd_hda_codec ir_nec_decoder 12459 0 snd_pcm 80845 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec ite_cir 24743 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ite_cir snd_timer 28931 2 snd_seq,snd_pcm wmi 18744 1 dell_wmi snd 62064 20 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_rawmidi,snd_seq,snd_seq_device,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer mac_hid 13077 0 soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm coretemp 13269 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141369 0 firewire_ohci 40172 0 sdhci_pci 18324 0 firewire_core 56906 1 firewire_ohci sdhci 28241 1 sdhci_pci crc_itu_t 12627 1 firewire_core lshw *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: 01 serial: 70:f1:a1:a9:54:31 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 ip=192.168.0.117 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0900000-f0903fff *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0b:00.0 logical name: eth0 version: 10 serial: b8:ac:6f:71:02:a6 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 firmware=sb v2.19 latency=0 link=no multicast=yes port=twisted pair resources: irq:48 memory:f0d00000-f0d0ffff

  Read the article

< Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >