Search Results

Search found 18303 results on 733 pages for 'network analyzation'.

Page 80/733 | < Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >

• Windows Server 2003 DC hangs after network drivers update

  - by tcv

  Earlier today, we attempted to update the Broadcom BCM5716C network drivers on a Windows Server 2003. (Dell PowerEdge T310, FWIW). Since then we have not been able to boot the server in any normal mode. Safe Mode works. Safe Mode with Networking and regular bootups hang at "Applying Network Settings." I haven't tried Last Known Good Configuration nor have I tried Directory Services Restore Mode. I should also mention that the longest I've allowed "Applying Network Settings" was perhaps 30 minutes. I spoke to Dell since the server is under a basic warranty. They sent me the original Broadcom drivers. The trouble seems to be, however, that since I can only boot in Safe Mode, I can't install the application package as given. In safe mode, I receive the error: "The system administrator has set policies to prohibit this installation." I can install the drivers independently, but that doesn't allow the NICs to work. The most I've been able to get are Code 10 errors on each NIC. I plan to get back to the site tomorrow to attempt installation of a different NIC. I'm wondering what else I can try.

  Read the article

• Internet Connection not working - USB LAN connection - from particular modem

  - by Paul

  I am trying to fix Internet connection on a friends Dell inspiron 1720 with XP service pack 3. It has an integrated network card that stopped working, after powering down/up the modem still didnt work I brought it back to my place to try a few things ie check cable, update driver etc... still didnt work. So I bought a USB LAN connector. It didnt work straight away but I went to configure the properties and changed the ConnectionType from AutoSense to 100 BaseT 10BaseT Full_Duplex, I basically just tried them all. From my place when connected to my desktop - 10 BaseT and 10BaseT Full_Duplex worked. From my place When connected to their laptop - 10 BaseT and 10BaseT Full_Duplex worked. Happy I went back to my friends house confident it would all work, and it didnt. Brought it back to mine and it did. While there, in Network Connections the connection is there recognized, enabled, 'working properly' it just says not connected. Also there is no led on the USB connector While at mine as above except there is an led on the USB connector and it says connected. Other difference I can think of is they have a cable modem, I'm plugged into the back of a Belkin wireless router - would this make a difference? Any other ideas what to try? (Would getting the model of the cable modem help anyone?) The USB connector is "DM9601 USB to Fast Ethernet"

  Read the article

• Static Network configuration with bridge in CentOS 6.2

  - by Kyle

  I have a server with CentOS 6.2 installed, I want to use it as a VM host to run some windows installations for development purposes. I wanted to be able to directly RDP and serve websites from IIS on these windows server installations, so I figured I would set it up as bridged networking. I have been struggling with this all morning, usually the result being that when I brought up the bridge interface all network connectivity to the CentOS would go away, however, I think I finally have that all figured out. However, here's what happens. The eth0 and br0 interfaces are defined in /etc/sysconfig/network-scripts with ifcfg-eth0 and ifcfg-br0. I DO NOT have ifup or ifdown or any other files for these interfaces, I have not found if they are needed. I can login and use firefox to browse the web, however, running ifconfig reveals that my eth0 does not have an IPAddress, but the br0 does. I can actually RDP into the Windows installation, and browse the internet from there as well, but I cannot directly connect(via putty, vnc, nor viewing web pages) to the CentOS box. Any idea what's up? ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none IPADDR=192.168.1.20 GATEWAY=192.168.1.1 NETMASK=255.255.255.0 NETWORK=192.168.1.0 ONBOOT=yes BRIDGE=br0 ifcfg-br0 DEVICE=br0 TYPE=Bridge BOOTPROTO=static DNS1=192.168.1.1 DNS2=8.8.8.8 GATEWAY=192.168.1.1 IPADDR=192.168.1.2 NETMAS=255.255.255.0 ONBOOT=yes I know some of the options are inconsistent (DNS and BOOTPROTO) because I tried changing those in the eth0 file to make it work, and the changes haven't adversly affected web browsing or the other functionality Thank you!

  Read the article

• Extending home network using multiple access point originating from another access point

  - by cyberjar09

  I have a home network with the current setup (RJ45 running from main router to access point) : +-------------+ +--------------+ | 192.168.2.1 | |192.168.2.2 | | router +--------------->access point 1| +-----^-------+ +--------------+ | | +-----+--------+ | 192.168.1.1 | | modem | +-----^--------+ | | | | +--+--+ | ISP | +-----+ However I would like to extend the network to two more floors in the house via the existing Access Point (router is too far and not reachable using a network cable, hence I need to extend using current access point). Please see diagram below : +-------------+ +--------------+ +----------------+ | 192.168.2.1 | |192.168.2.2 | | 192.168.2.3 | | router +--------------->access point 1+----------> access point 2 | +-----^-------+ +--------+-----+ +----------------+ | | | | +-----+--------+ | | 192.168.1.1 | | | modem | | +-----^--------+ | +----------------+ | +----------------> 192.168.2.4 | | | access point 3 | | +----------------+ | +--+--+ | ISP | +-----+ Q1 : is this setup possible? Q2 : if possible, will I have to do anything different from what I did to setup access point 1? edit 1 : I am trying to study the dd-wrt documentation to see which would be the correct mode of operation for me Linking Routers but Im confused because I dont see any info on how to use an existing Access point to extend the signal of the SSID. If anyone could point me to the correct wiki for how I should setup AP2 and AP3 based on AP1, it would be very helpful. For AP1, I did the following Use static IP and setup same SSID as primary wireless router use same security as primary wireless router make AP1 point to 192.168.2.1 (primary router) for DHCP Thanks in advance.

  Read the article

• Abysmal transfer speeds on gigabit network

  - by Vegard Larsen

  I am having trouble getting my Gigabit network to work properly between my desktop computer and my Windows Home Server. When copying files to my server (connected through my switch), I am seeing file transfer speeds of below 10MB/s, sometimes even below 1MB/s. The machine configurations are: Desktop Intel Core 2 Quad Q6600 Windows 7 Ultimate x64 2x WD Green 1TB drives in striped RAID 4GB RAM AB9 QuadGT motherboard Realtek RTL8810SC network adapter Windows Home Server AMD Athlon 64 X2 4GB RAM 6x WD Green 1,5TB drives in storage pool Gigabyte GA-MA78GM-S2H motherboard Realtek 8111C network adapter Switch dLink Green DGS-1008D 8-port Both machines report being connected at 1Gbps. The switch lights up with green lights for those two ports, indicating 1Gbps. When connecting the machines through the switch, I am seeing insanely low speeds from WHS to the desktop measured with iperf: 10Kbits/sec (WHS is running iperf -c, desktop is iperf -s). Using iperf the other way (WHS is iperf -s, desktop iperf -c) speeds are also bad (~20Mbits/sec). Connecting the machines directly with a patch cable, I see much higher speeds when connecting from desktop to WHS (~300 Mbits/sec), but still around 10Kbits/sec when connecting from WHS to the desktop. File transfer speeds are also much quicker (both directions). Log from desktop for iperf connection from WHS (through switch): C:\temp>iperf -s ------------------------------------------------------------ Server listening on TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [248] local 192.168.1.32 port 5001 connected with 192.168.1.20 port 3227 [ ID] Interval Transfer Bandwidth [248] 0.0-18.5 sec 24.0 KBytes 10.6 Kbits/sec Log from desktop for iperf connection to WHS (through switch): C:\temp>iperf -c 192.168.1.20 ------------------------------------------------------------ Client connecting to 192.168.1.20, TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [148] local 192.168.1.32 port 57012 connected with 192.168.1.20 port 5001 [ ID] Interval Transfer Bandwidth [148] 0.0-10.3 sec 28.5 MBytes 23.3 Mbits/sec What is going on here? Unfortunately I don't have any other gigabit-capable devices to try with.

  Read the article

• Hyper-V Virtual Machine won't respond over network

  - by Brad Gignac

  Recently, one of our Hyper-V virtual machines has periodically stopped responding over the network. It seems to be happening every few days, and it occasionally happens up to several times a day. I am by no means a sysadmin, so any direction you guys could provide would be very welcome. I've included everything I know to include below. If you need any additional information, I'll be glad to include it. I can connect through the Hyper-V console. I can't connect to network shares, IIS web apps, using RDP, or using ping. Memory usage seems to be normal (3 of 4 GB) Processor usage seems low. We don't know the exact time the server goes down, but the following error appears consistently around the time it goes down: Error 5719, NETLOGON This computer was not able to set up as secure session with a domain controller in domain *** due to the following: There are currently no logon servers available to service the logon request. This may lead to authentication problems. Make sure that this computer is connected to the network. If this problem persists, please contact your domain administrator.

  Read the article

• permanent NAS-mount in Ubuntu - wrong fs type, bad option, bad superblock

  - by Emil

  My network drive shows up in the file browser, just like my external usb-harddrive. Moving, running and editing files works. Hovering over it shows smb://lacie-2big/nasdisk . BUT, when I want to save a file, the drive doesn't come up as an option. All I can see is my other places, including my usb-harddrive. I am a complete newbie but I am GUESSING that it has something to do with the mount not being a "real" mount but just a shortcut to the smb location. So I ran the tutorial at https://wiki.ubuntu.com/MountWindowsSharesPermanently about how to "mount a network drive permanently". edited my fstab to //LaCie-2big/nasdisk /media/nasmount cifs guest,uid=1000,iocharset=utf8,codepage=unicode,unicode 0 0 and running sudo mount -a gave me the following error: mount: wrong fs type, bad option, bad superblock on //LaCie-2big/nasdisk, missing codepage or helper program, or other error (for several filesystems (e.g. nfs, cifs) you might need a /sbin/mount. helper program) In some cases useful info is found in syslog - try dmesg | tail or so Now thats a very helpful error message, BUT, before I go any further, I'd be really thankful if one of you could tell me if I'm even in the right ballpark, or if my actual need: to be able to download files (ie torrents) directly to the drive, can be possible as it is already. Question: How to fix "wrong fs type, bad option, bad superblock on //LaCie-2big/nasdisk, missing codepage or helper program" when running mount -a

  Read the article

• Unable to Access Certain Websites

  - by codejoust

  Through a local network, all computers except one ubuntu machine can access 1. Adobe.com 2. Icann.org 3. Apache.org 4. Example.com. The ubuntu machine returns (in firefox): "Though the site seems valid, the browser was unable to establish a connection." Furthermore, when I traceroute those websites using the ubuntu machine, they all return ubuntu.local, and it ends there: (traceroute to icann.org (192.0.32.7), 30 hops max, 40 byte packets 1 ubuntu.local (192.168.1.105) 3000.791 ms !H 3000.808 ms !H 3000.814 ms !H I've checked the hosts file, and there isn't anything in there, and I have an apache server there so if it was redirected to localhost, I'd probably see the localhost webroot page. Thanks in advance! user@ubuntu:~$ netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 192.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 The Ubuntu Machine is one of six on the network. I'm using opendns for dns, so I do think that should be a problem.

  Read the article

• Chrome browser completely messing with network?

  - by kiasecto

  I have a bizare problem with Google Chrome on a intel core i5 running windows 7 32bit. Whenever chrome is installed, access to other computers in the home group becomes really slow - such as opening shares. Its becomes really slow to resolve windows names. Something goes hay-wire with the local network - pining local machines which is usually 0mS pings I get random timeouts and random successes. Whenever I try to load a local address inside of chrome (including localhost, 192.168.0.1 etc) - it always says something in the status bar about resolving proxy and times out after about 5 seconds, then seems to work fine. If I go to settings inside of chrome, it just brings up the internet explorer connection settings, where I have not set any proxy settings. One I uninstall chrome, all these problems go away. Network shares and name resolvings work instantly, pings to any machines never have a problem. Localhost and other network IP address work fine in all other browsers. Anyone heard of this problem before and know what it might be? I even tried re-installing winodws 7 and the problem came straight back when chrome was loaded on again.

  Read the article

• Painfully slow login to AD bound Mac OS X Leopard machine when off home network

  - by GeeBee

  Dear all Just looking for a little help with this problem that seems to trip a lot of people up and is causing me no end of grief. I have a number of fully patched OS X Leopard machines that are bound to my AD (Server 2003). When on the home network, logging in seems swift and works as expected. When users take the machines off site, login can take 5 minutes or more. The user adds correct credentials but the desktop does not appear for a very long time. Outside the office, I have tried logging in using a local Admin account, switching off Airport and then logging in using an AD account. In this situation login is immediate again. It all seems as if Leopard is finding a suitable wireless network, spending far too long looking for the Domain before eventually giving up and using the cached credentials instead. I have read that disabling Bonjour on the machine will stop this problem (i have not yet tested) http://www.macwindows.com/leopardAD.html#111607z ...but I am reluctant to use this "Solution" as I would like to be able to use Bonjour on the local network as well as having AD-bound machines. However, is disabling Bonjour really the only answer? Is there not some time-out setting somewhere that could be amended to stop Leopard spending forever looking for home? Any help would be very gratefully received Thanks Gordon

  Read the article

• Two DHCP servers on the same network

  - by CesarGon

  We are setting up a routing link between the Windows Server 2008 networks of two different buildings in my organisation. Each network uses a different IP addressing scheme (one uses public addresses, the other one uses private), but the goal is having a single Windows Server domain across the gap between the buildings. The link is provided by a 100-Mbps point-to-point line. I have always understood that you should not have more than one DHCP server on a network. However, we are planning to put a domain controller on each building, and each domain controller will be a DNS server and a DHCP server as well. The intention is that a machine booting up in building A gets its IP address from the DHCP server closer to it, in building A, while a machine booting up in building B gets an address from the DHCP server in building B. Since the two buildings will be linked and the network will be only one, will this work? How can I avoid that a machine booting up in building A gets an address from the DHCP server in building B (or vice versa)? Thanks.

  Read the article

• Two DHCP servers on the same network

  - by CesarGon

  We are setting up a routing link between the Windows Server 2008 networks of two different buildings in my organisation. Each network uses a different IP addressing scheme (one uses public addresses, the other one uses private), but the goal is having a single Windows Server domain across the gap between the buildings. The link is provided by a 100-Mbps point-to-point line. I have always understood that you should not have more than one DHCP server on a network. However, we are planning to put a domain controller on each building, and each domain controller will be a DNS server and a DHCP server as well. The intention is that a machine booting up in building A gets its IP address from the DHCP server closer to it, in building A, while a machine booting up in building B gets an address from the DHCP server in building B. Since the two buildings will be linked and the network will be only one, will this work? How can I avoid that a machine booting up in building A gets an address from the DHCP server in building B (or vice versa)? Thanks.

  Read the article

• Is it possible to provide a wired ethernet connection to external devices with an extra LAN card?

  - by Ben McCormack

  I'm trying to provide a wired ethernet connection (wireless is not an option for this device) to a device (Samsung blu-ray player) without running Cat5 cable all over the home. I have a PC sitting next to this device and the PC is connected to the network via a wireless USB adapter. Is it possible to provide a wired connection from the PC to the wired device using the (currently unused) ethernet port in the back of the computer? Here's how I envision the device getting connected to the internet via my network: Linksys WRT54G v8 Wireless Router | ``--> Windows 7 PC connected via wireless | ``--> Blu-ray player connected via wired connection to the ethernet port on the PC. If so, how is this done? Will I need a crossover cable? What settings will I need to change in Windows 7 so that the device can connect? NOTE: I'm trying to avoid having to buy a wireless bridge and/or hacking a router with an open-source firmware to get this to work. See my previous question for more details.

  Read the article

• Network Misconfiguration when adding first host to new vSphere cluster

  - by dunxd

  I am building a new vSphere cluster from scratch. I have installed ESXi on the first host, and built a vCenter server on a VM residing on that host (storage is on the local hard drive, although we have iSCSI targets which I can reach from the host). The cluster is configured for HA. When I try and add the host to the cluster, I get an error at the point where HA is configured - Cannot complete the . I have stripped the network configuration of the host down to the most basic - a single NIC attached to a single vSwitch - this is running the VMKernel Port on VLAN 8 - that is our Management VLAN. The vCenter server will have a network address on this VLAN, so I also set the initial Virtual Machine Port Group to this VLAN, and connected the vCenter server NIC to this port group. I understand I can't connect the vCenter server to the VMkernel port group, but shouldn't I be able to connect the vCenter server to a Port Group in the same VLAN? If not, do I need to create a VLAN specifically for VMKernel Port Group? I plan to set up another port group for vMotion with a dedicated and isolated VLAN (i.e. VLAN isn't routed) so this wouldn't allow vCenter to communicate. Does anyone have any suggestions, or other ideas for what might be causing the problem. I've read through the documentation, but it isn't giving me any pointers, and the error message isn't helping me beyond telling me something is wrong with my network config.

  Read the article

• Network problems with Ubuntu on VMware

  - by svick

  I'm running Ubuntu 10.04 inside VMware Player running under Windows Vista and I can't connect to the internet or the host computer from the Ubuntu. I have set all the VMware services to “manual” (like VMware DHCP Service), but starting them manually doesn't help. In VMware, the network seems to work (there is a green dot beside the network icon) and I have tried both Bridged and NAT settings. ifconfig doesn't show the eth1 interface, unless I give it as a parameter (or use -a). I think this means that Ubuntu thinks that the network isn't connected at all. How do I fix this? ifconvadmin@ubu1004:~$ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:56 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4192 (4.1 KB) TX bytes:4192 (4.1 KB) vadmin@ubu1004:~$ ifconfig eth1 eth1 Link encap:Ethernet HWaddr 00:0c:29:2d:a0:6f BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:18 Base address:0x2000

  Read the article

• Single computer on network cannot connect to internet.

  - by user34630

  Hi All, I hope you can help me out! :) I have 3 computers and one device (Xbox) on my home network; 2 running XP and one on Vista. The computer that can't connect to the internet (XP) is old and failing, and shows no warning before it completely runs out of battery. Thus today, I started it up forgetting that I had unplugged it the night before, and it just ran out of battery entirely whilst I was using it and died. I think that before this I had been browsing the internet, but I can't remember for certain. (i.e. The problem I am having may or may not have been caused by this 'hard' power off). Anyway, now when I start the computer up it takes 5-10 minutes after logging on to display the start bar and icons. Also, I cannot browse the internet. The computer seems to connect to the network OK (I have tried both wired and wireless), but I can't visit sites and can't ping web addresses. Pinging the router fails, as does pinging another of my computers on the network. I have never encountered something like this before, and whilst I am no noob I am also not a sysadmin, haha. :( Any help is greatly appreciated, thank you for your time. P.S. I have tried a system restore (newbie move?).

  Read the article

• Is browser based wireless authentication secure?

  - by johnnyb10

  Our wireless network previously used a preshared WPA/WPA2 key for guest access, which allows them access to the Internet. (Our employee access uses 802.1x authentication). We just had a wireless consultant come in to fix various wireless issues we had; one of the things he wound up doing was changing our guest access to HTML-based instead of the preshared key. So now that guest SSID is open (instead of using WPA) and users are presented with a browser-based login screen before they can get on the Internet. My question is: Is this an acceptable method from a security standpoint? I would assume that having an open network is necessarily a bad idea, but the consultant said that the traffic is still using PEAP, so it's secure. I didn't get a chance to question him further on this because we ran late and a bunch of other things came up. Please let me know what you think about the advantages/disadvantages of using HTML-based wireless authentication as opposed to using a preshared WPA key. Thanks...

  Read the article

• Ubuntu second static IP, ifconfig, /etc/network/interfaces

  - by Schmoove

  I would like to add a second static IP to my local Ubuntu 11.10 desktop machine and have it automatically available after rebooting. So far I am successfully using ifconfig to to temporarily set up an alias for my primary network interface: # ifconfig eth1:0 192.168.178.3 up # ifconfig eth1 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.2 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:feef:a3d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:61929 errors:0 dropped:0 overruns:0 frame:0 TX packets:64034 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:45330863 (45.3 MB) TX bytes:28175192 (28.1 MB) Interrupt:42 Base address:0x4000 eth1:0 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.3 Bcast:192.168.178.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:42 Base address:0x4000 However, when I add the following to /etc/network/interfaces, the alias is not up and running as expected after a reboot: # vi /etc/network/interfaces auto eth1:0 iface eth1:0 inet static address 192.168.178.3 netmask 255.255.255.0 I would like to know what to configure to get this to work. As a side note, I am running gnome shell.

  Read the article

• Free tiered storage automation in linux?

  - by NginUS

  I have a couple virtualized fileservers running in QEMU/KVM on ProxmoxVE. The physical host has 4 storage tiers with significant performance variances. They're attached both locally and via NFS. These will be provided to the fileserver(s) as local disks, abstracted into pools, and handling multiple streams of data for the network. My aim is for this abstraction layer to intelligently pool the tiers. There's a similar post on the site here: Home-brew automatic tiered storage solutions with Linux? (Memory - SSD - HDD - remote storage) in which the accepted answer was a suggestion to abandon a linux solution for NexentaStor. I like the idea of running NexentaStor. It almost fits the bill. NexentaStor provides Hybrid Storage Pools, and I love the idea of checksumming. 16TB without incurring licensing fees is a huge plus as well. After the expense of the hardware, free is about all my budget can handle. I don't know if zfs pools are adaptive or dynamically allocated based on load, but it becomes irrelevant since NexentaStor doesn't support virtio network or block drivers, which is a must in my environment. Then I saw a commercial solution called SmartMove: http://www.enigmadata.com/smartmove.html And it looks like a step in the right direction, but I'm so broke I'd be wasting their time to even ask for a quote, so I'm looking for another option. I'm after a linux implementation that supports virtio drivers, and I'm at a loss as to which software is up to it.

  Read the article

• maximum number of connections Squid

  - by Isaac

  I have a Squid proxy server that controls all internet traffic for my network. I need a way to stop users from downloading big files (say 50MB) in my network. I banned some famous ports (e.g. torrent) but some downloads are possible by HTTP port. Obviously I cannot ban port 80! A simple solution is limiting maxmimum number of the simultaneous connections for each IP (e.g. 3 connections). It's possible in Squid with this config: acl ACCOUNTSDEPT 192.168.5.0/24 acl limitusercon maxconn 3 http_access deny ACCOUNTSDEPT limitusercon But this solution has really bad impact in web browsing, because any smart browser get different parts of a website by several connections simultaneously to speedup web browsing. But if we have a maximum number of connections, the browsers will fail to get some parts and the website will be shown partially and some parts/images/frames will not be shown. So, can we limit maximum number of persist connections? I think this policy will works: Specify Maximum number of connections that is alive for 10 seconds But Number of simultaneous connections for every IP is unlimited But how can we implement this policy when Squid? With which config? UPDATE: artifex and Tom Newton offered using a bandwidth-limiting approach to fight against downloaders. But bandwidth-limiting in Squid has a shortcoming: It's static and cannot dynamically change. So a person has a limited bandwidth not matter how many people are using internet (maybe nobody!) Also, this solution cannot help to stop people from downloading. They still can download but in a lower speed. But if we find a way to terminate persist connections (or any connection that is alive more than a specific time), downloading big files will be almost impossible (always there is some way!)

  Read the article

• Central Authentication For Windows, Linux, Network Devices

  - by mojah

  I'm trying to find a way to centralize user management & authentication for a large collection of Windows & Linux Servers, including network devices (Cisco, HP, Juniper). Options include RADIUS/LDAP/TACACS/... Idea is to keep track with staff changes, and access towards these devices. Preferably a system that is compatible with both Linux, Windows & those network devices. Seems like Windows is the most stubborn of them all, for Linux & Network equipment it's easier to implement a solution (using PAM.D for instance). Should we look for an Active Directory/Domain Controller solution for Windows? Fun sidenote; we also manage client systems, that are often already in a domain. Trust-relationships between Domain Controllers isn't always an option for us (due to client security restrictions). I'd love to hear fresh ideas on how to implement such a centralized authentication "portal" for those systems.

  Read the article

• Backup Exec 10 - Network connection to the remote agent has been lost

  - by jherlitz

  Okay, so I have 4 remote offices, all running off of a 3mb ethernet connection. Two sites are part of a WAN and 2 sites are using 3mb connections over a site to site tunnel. I am using Backup Exec 2010, I have the remote agent installed on all the remote servers. For the past few weeks now, on the two sites running over the site to site tunnel have been failing with the following error message now. "The network connection to the Backup Exec Remote Agent has been lost. Check for network errors" We used to be on a DSL connection site to site tunnel, now we changed to the 3mb ethernet connection using site to site tunnel. I have to find out, has it been failing ever since we changed, or just recently. Backup exec support is telling me it is a network issue. My communication or connection to the server is solid, we don't have any issues, or outages. So I am baffled on why this continues to fail. And why just those two sites.. Any advice?

  Read the article

• Windows : Map-a-network-drive to a remote Shared-Folder (on QNAP NAS) using OpenVPN

  - by spelltox

  Provided my lack of networking knowledge, I've been struggling with this issue for quite a few days now : I have a QNAP-TS212 NAS on which i've created a shared-folder (mostly excel files). All the computers in the local network (windows) are able to access it without any problem. Now, i want to access that shared-folder remotely (windows client), so : I enabled OpenVPN (and PPTP) in QNAP admin. Installed OpenVPN on the remote client. Applied the configuration file that the QNAP generated - Configuration (openvpn.ovpn) : client dev tun script-security 3 proto udp remote ***MY_WAN_IP*** 1194 resolv-retry infinite nobind ca ca.crt auth-user-pass reneg-sec 0 cipher AES-128-CBC comp-lzo OpenVPN connect successfully from the remote client. Now, here's my problem : I can ping the NAS (got IP 10.8.0.1) from the remote client, But when i try to map-a-network-drive, i don't see the shared folder or the NAS or any of the other computers in the network... I checked - all computers are in "WORKGROUP" workgroup. I'm probably missing some basic knowledge, So - any help would be greatly appreciated ! Many thanks.

  Read the article

• "Safe" personal router use on apartment-wide network

  - by noisetank

  I recently moved into an apartment with internet included in my rent. This was a boon at first, but now I'm feeling limited. To get devices connected (wired or wireless), I have to whitelist the MAC addresses on mycampusnet.com. This is annoying (considering I'm well over the 10 device limit including my roommate's stuff), but what's really driving me mad is that I don't seem to have any semblance of a "local" network. I've relied heavily on static IPs and port forwarding in the past (accessing NAS and remote desktop) and (as far as I can understand), that functionality is nonexistent without my router set up. Also, as my wired and wireless devices don't always seem to make it onto the same subnet, I'm unable to use any of my iDevices with my Apple TV (I can, however, mirror to no less than four strangers' Apple TVs at any moment, which is a whole other level of discomforting). I've talked to the head of the apartment complex and she told me that they personally don't have any issue with my using a router, but the provider (CampusConnect) does not currently allow it. Apparently, enough people have put in complaints/requests about the restriction (the apartments are for graduate students and University staff, many of which need to set up things like VPNs for work reasons) to open up some sort of ticket to get the functionality in place, but all the calls I've made to get status updates have been a waste of time. My question is: If I plugged my router into the apartment network, what would happen? I've been told already that personal routers would "interfere with the wireless" and that they would shut my port down if I used one, but is that a legitimate thing or just something made up that sounds real to keep the average Joe from pushing it further? I'm guessing there's some way of configuring my router to keep it from disrupting the rest of the network, but it's not something they want to tell me for obvious reasons. Am I right? And if so, what are the chances that they'd notice the difference in traffic or whatever and shut off my port?

  Read the article

• Arch Linux drops me on my school network

  - by Kravlin

  I'm running a Lenovo X61 which i carry around my college for getting on the internet at various points in the day. The network has always been finicky but recently it's gotten worse. I'll connect using iwconfig, get an ip from dhcpcd and log in using vpnc to their system. Sometimes I'll stay connected for hours but most of the time within 30 seconds my network traffic will drop to zero and i'll be unable to do anything. My computer still belives it's connected, however to try again i need to put my wireless interface down, put it back up and try again. It's gotten so bad that i've got a window on my computer pinging yahoo or google constantly in order to know if i'm still able to get online. I know other people who have used Arch Linux that don't have the same problems as well as people who use Ubuntu who haven't had any problems either. It seems like my computer is a special case. Does anyone have any suggestions on how to fix it? dmesg doesn't show anything out of the ordinary going on and i don't know where else to look for errors or other things to try. Edit: this doesn't happen on my home network. It's a problem that only happens at school.

  Read the article

< Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >