Search Results

Search found 32610 results on 1305 pages for 'internet options'.

Page 81/1305 | < Previous Page | 77 78 79 80 81 82 83 84 85 86 87 88 | Next Page >

wireless detected but Can't connect to network, Wifi card intel pro wireless N100 BGN

- by Alexandre777

Thanks in advance, I installed Linux Mint kernel 3.0.0-12 x64 ,wireless is detected and I configure it in network manager but can't coonect, there are the results of command line: $ iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off $ sudo lshw -C network** *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:51:c9:d6 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:48 memory:d7400000-d7401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: c0 serial: 48:5b:39:99:8f:16 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.2 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:51 memory:d3800000-d383ffff ioport:8000(size=128 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Thank you.

Read the article
Save chromium browser's session

- by Anwar Shah

How to manually save session in chromium-brower. I have a Notebook with damaged battery (only gives 5~6 minutes of backup, planning to buy a new one), and in our country "Load Shedding" (power outages) is quite common. So, I had to close my session before shutting down my laptop. When I re-open chromium, there is no tab with previous session. The question is: How can i manually save my session before closing the laptop?

Read the article
Why do browsers leak memory?

- by Dane Balia

A colleague and I were speaking about browsers (using a browser control object in a project), and it appears as plain as day that all browsers (Firefox, Chrome, IE, Opera) display the same characteristic or side-effect from their usage and that being 'Leaking Memory'. Can someone explain why that is the case? Surely as with any form of code, there should be proper garbage collection? PS. I've read about some defensive patterns on why this can happen from a developer's perspective. I am aware of an article Crockford wrote on IE; but why is the problem symptomatic of every browser? Thanks

Read the article
How to future-proof my touch-enabled web application?

- by Rice Flour Cookies

I recently went out and purchased a touch-screen monitor with the intention of learning how to program touch-enabled web applications. I had reviewed the MDN documentation about touch events, as well as the W3C specification. To get started, I wrote a very short test page with two event handlers: one for the mousedown event and one for the touchstart event. I fired up the web page in IE and touched the document and found that only the mousedown event fired. I saw the same behavior with Firefox, only to find out later that Firefox can be set to enable the touchstart event using about:config. When touch events are enabled, the touchstart event fires, but not mousedown. Chrome was even stranger: it fired both events when I touched the document: touchstart and mousedown, in that order. Only on my Android phone does it appear to be the case that only the touchstart event fires when I touch the document. I did a a Google search and ended up on two interesting pages. First, I found the page on CanIUse for touch events: http://caniuse.com/#feat=touch Can I Use clearly indicates that IE does not support touch events as of this writing, and Firefox only supports touch events if they are manually enabled. Furthermore, all four browsers I mentioned treat the touch in a completely different way. It boils down to this: IE: simulated mouse click Firefox with touch disabled: simulated mouse click Firefox with touch enabled: touch event Chrome: touch event and simulated mouse click Android: touch event What is more frustrating is that Google also found a Microsoft page called RethinkIE. RethinkIE brags about touch support in IE; as a matter of fact, one of their slogans is "Touch the Web". It links to a number of touch-based application. I followed some of these links, and as best I can tell, it's just like CanIUse described; no proper touch support; just simulated mouse clicks. The MDN (https://developer.mozilla.org/en-US/docs/Web/API/Touch) and W3C (http://www.w3.org/TR/touch-events/) documentation describe a far richer interface; an interface that doesn't just simulate mouse clicks, but keeps track of multiple touches at once, the contact area, rotation, and force of each touch, and unique identifiers for each touch so that they can be tracked individually. I don't see how simulated mouse clicks can ever touch the above described functionality, which, once again, is part of the W3C specification, although it is listed as "non-normative", meaning that a browser can claim to be standards-compliant without implementing it. (Why bother making it part of the standard, then?) What motivated my research is that I've written an HTML5 application that doesn't work on Android because Android doesn't fire mouse events. I'm now afraid to try to implement touch for my application because the browsers all behave so differently. I imagine that at some time in the future, the browsers might start handling touch similarly, but how can I tell how they might be handled in the future short of writing code to handle the behavior of each individual browser? Is it possible to write code today that will work with touch-enabled browsers for years to come? If so, how?

Read the article
http, https and ftp is not working but smtp and imap is working

- by Unicron

hi all, yesterday on a computer of a friend a strange thing happened. after booting the ports fo http, https and ftp are closed but e-mail is still working. in the control panel the windows firewall seems active even if he tries to deactivate it. i have a suspision that it is the faul of norton internet security 2010, we have tried to uninstall it, but the uninstallation did not work. when using the removal tool from symantec it just goes to 23% and then it crashes. the process ccSvcHst.exe is still running. how can i safeley remove the rest of norton internet security? thanks in advance [edit] norton internet security 2010 is sucesfully removed, but still no connectivity

Read the article
What would be the total expenses of running an in-home web server?

- by techaddict

I have several hosting accounts with companies, and plan to keep them. However, I would like to try my hand at creating my own home web-server, both for fun and for the learning experience. I would like to know the expenses involved, including: electricity costs (greater than light bulb?) internet costs (will I have to upgrade my internet? Or is 3-5Mbps upload speed fine for a web server with medium amount of traffic? Would I have to get a separate internet connection?) other unknown expenses Consider that I will configure the web server myself, so that is not an expense. Also consider that I already have a computer (year-old Dell laptop, 15R) to use to be dedicated as the web server.

Read the article
wired connection not working in ubuntu 12.04 on lenovo G580 laptop

- by shravankumar

I found solution in http://www.zyxware.com/articles/2680/solved-wired-connection-eth0-not-detected-in-ubuntu-12-04 I downloaded compact-wireless-2012-07-03-p.tar.bz2 Here the steps i followed along with output 1. shravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ scripts/driver-select alx Output: Processing new driver-select request... Backup exists: Makefile.bk Backup exists: Makefile.bk Backup exists: drivers/net/ethernet/broadcom/Makefile.bk Backup exists: drivers/net/ethernet/atheros/Makefile.bk Backup exists: Makefile.bk Backup exists: Makefile.bk Backup exists: drivers/net/ethernet/broadcom/Makefile.bk 2.shravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ make output: make -C /lib/modules/3.2.0-23-generic/build M=/home/shravankumar/Desktop/compat-wireless-2012-07-03-p modules make[1]: Entering directory `/usr/src/linux-headers-3.2.0-23-generic' scripts/Makefile.build:44: /home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros/alx/Makefile: No such file or directory make[4]: *** No rule to make target `/home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros/alx/Makefile'. Stop. make[3]: *** [/home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros/alx] Error 2 make[2]: *** [/home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros] Error 2 make[1]: *** [_module_/home/shravankumar/Desktop/compat-wireless-2012-07-03-p] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.2.0-23-generic' make: *** [modules] Error 2 3. hravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ make install output: FATAL: Could not open /lib/modules/3.2.0-23-generic/modules.dep.temp for writing: Permission denied make: *** [uninstall] Error 1 4. shravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ modeprobe alx output: No command 'modeprobe' found, did you mean: Command 'modprobe' from package 'module-init-tools' (main) modeprobe: command not found I am new to Ubuntu ,Please help me. Thanks in advance

Read the article
Awesome Bookmarklet Collection Ready to Select from and Add to Your Browser

- by Asian Angel

Bookmarklets are extremely useful additions to have for your everyday browsing needs without the hassle (or slowdown effect) of extensions. With that in mind tech blog Guiding Tech has put together a terrific collection of 21 bookmarklets that are ready to add to your favorite browser. Just scroll down and select/install the bookmarklets you like from the blog post and enjoy the enhanced browsing! You can see the beginning and end results from our sample use of the Search Site Bookmarklet in the screenshots above and below… Note: We altered the bookmarklet slightly to focus the search results through Google Singapore. How to Stress Test the Hard Drives in Your PC or Server How To Customize Your Android Lock Screen with WidgetLocker The Best Free Portable Apps for Your Flash Drive Toolkit

Read the article
Web standards or risk avoidance?

- by Junior Dev

My company is building an App Engine application. The app encounters a bug (possibly due to an issue with App Engine itself, as per our research) on IE9, but it cannot be reliably reproduced and is experienced by a small percentage of users. The workaround is to force IE9 to use IE8 mode. As a lazy front end developer (who doesn't like CSS hacks, shims and polyfills) I think it's OK to at least try going back to IE9 mode and see what happens, while we're still in private beta. The senior engineer (being more pragmatic) would rather that we continue forcing IE9 users to use the older IE8 mode. Who is right?

Read the article
What should we tell our unsupported IE6 users?

- by Dan Fabulich

In the upcoming version of our web app, we've broken IE6, and we don't intend to fix it. We've had a clear warning posted for IE6 users for some months; we've decided it's time not to support it. My question is: how should we communicate this to our users? Some people here feel that we should block IE6 users who would try to access the web app, because it's not going to work for them. Others feel that we should just leave up a warning, saying "This doesn't work in IE6," but not block them; instead, if they click to dismiss the warning, just let them in to the broken site to see for themselves that it doesn't work. Who is right? Is there a better way?

Read the article
Wired Network not working on Ubuntu 11.10 + Strange Behavior with Manual Conf

- by Mauricio Cruz

I'm new to Ubuntu - to be honest this is my very first day trying it... and I've already spent hours trying to make my wired connection work. I've been using this wired network with Windows and OSX, and in both systems I also had some trouble trying to connect in the past (and the troubleshooters did their magic and helped me get connected). Today, this is what I got: I'm running Ubuntu 11.10; ifconfig: eth0 Link encap:Ethernet HWaddr 78:2b:cb:c3:bf:8f UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1 errors:0 dropped:0 overruns:0 frame:0 TX packets:343 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:70 (70.0 B) TX bytes:63273 (63.2 KB) Interrupt:20 Memory:e2e00000-e2e20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1859 errors:0 dropped:0 overruns:0 frame:0 TX packets:1859 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:149368 (149.3 KB) TX bytes:149368 (149.3 KB) wlan0 Link encap:Ethernet HWaddr 10:0b:a9:82:55:c0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:15484 errors:0 dropped:0 overruns:0 frame:0 TX packets:16871 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:12048377 (12.0 MB) TX bytes:2677679 (2.6 MB) I also have some information from Windows ipconfig /all that I ran at my friend's machine Ipv6 Address: <address> preferential Ipv4 Address: 172.26.65.23 <preferential> Netmask: 255.255.254.0 Default Gateway: 172.26.64.1 DHCP Server : <address> DNS Servers : <address> DNS Suffix : <suffix> The weird thing is that I've tried to configure everything manually, using "Network Connections". When I add everything inside IPv4 Settings, the connection is finally successful, but only for 4~5 seconds before getting disconnected again... Update:I just changed the Connection Method to "Local-Link Only", and the same described above happens: At first, it says "Connection Stablished", but after a few seconds, the wired network gets disconnected. I hope someone can help me get connected! Thanks!

Read the article
Equivalent to Freedom and/or Anti-Social?

- by mummey

Freedom: http://macfreedom.com/ Anti-Social: http://anti-social.cc/ Simply put: Where can I find a equivalent to either-or/both these apps? Note: Part of the appeal of these apps is allowing the user to explicitly make it extra difficult to re-enable these services. Unplugging the network cable might seem to achieve the same results from an glance, but the added difficulty in re-enabling those services is what makes these apps valuable.

Read the article
ASP.NET developers build rich management system using the VWG extension

- by Visual WebGui

When The Center for Organ Recovery & Education (CORE) decided they needed a web application to allow easy access to the expenses management system they initially went to ASP.NET web forms combined with CSS. The outcome, however, was not satisfying enough as it appeared bland and lacked in richness. So in order to enrich the UI and give the web application some glitz, Visual WebGui was selected. Visual WebGui provided the needed richness and the familiar Windows look and feel also made the transition...(read more)

Read the article
Firefox clones for Ubuntu

- by cipricus

In Windows I use, beside the main Firefox installation, one or even two "Firefox clones" for different purposes (specifically oriented addons and configurations, light configuration without addons, configuration for a different user, etc). A clone of Firefox is a browser that is identical to Firefox except the name. (It may have more - but not less - features than FF and it must be installable beside Firefox, not on top/instead of it. So, a clone is not a replacement/exclusive alternative of FF: in the way Swiftfox is, taking all previous Firefox extensions and configuration.) For example, in Windows, Pale Moon, Cometbird and Wyzo are FF clones (but they do not have Linux support). Basically, Flock browser would also qualify, and it had support for Linux: but it was discontinued. What remains as closest to being a full clone is Seamonkey, has support for Linux, but it is not a complete clone (although it can use a lot of FF extensions): themes are not working, the interface is in general different and rather primitive. It has the merit of keeping the pace with FF 4+ (in contrast with Swiftweasel, for example.) Are such more browsers available in Ubuntu? (As for comments asking why I "really" need these clones, I am just used to doing that, I like two separate Firefox-like browsers: why pleasure, just like curiosity, would not be enough??)

Read the article
How to protect a peer-to-peer network from inappropriate content?

- by Mike

I’m developing a simple peer-to-peer app in .Net which should enable users to share specific content (text and picture files). As I've learned with my last question, inappropriate content can “relatively” easily be identified / controlled in a centralized environment. But what about a peer-to-peer network, what are the best methods to protect a decentralized system from unwanted (illegal) content? At the moment I only see the following two methods: A protocol (a set of rules) defines what kind of data (e.g. only .txt and jpg-files, not bigger than 20KB etc.) can be shared over the p2p-network and all clients (peers) must implement this protocol. If a peer doesn’t, it gets blocked by other peers. Pro: easy to implement. Con: It’s not possible to define the perfect protocol (I think eMail-Spam filters have the same problem) Some kind of rating/reputation system must be implemented (similar to stackoverflow), so “bad guys” and inappropriate content can be identified / blocked by other users. Pro: Would be very accurate. Con: Would be slow and in my view technically very hard to implement. Are there other/better solutions? Any answer or comment is highly appreciated.

Read the article
IE9 Loses Some CSS After Particular Form Submit [migrated]

- by Asherion

The site I am editing has a search form. For the record, there are several other forms on the site, contact and the like. This is the only one with an issue. Upon submission of the form, SOME of the styling is lost in IE9 (possibly other versions of IE, haven't tested that yet). Primarily, the margins and colors set in html and body appear to have been lost. Menus, banner, text, etc all appear to retain styles. All styles are on one sheet, that are used here... Any helpful advice? Here is the contents of the search page and the php used to check for the form, if that helps, and the css that I think is lost. THE HTML: <div id="search"> <br /> <div style="float:right;font-size:.8em;"> <form name="form_sidesearch" action="search.html" method="post"> <input type="hidden" name="action" value="search" /> <input type="text" name="search_value" value="<?php echo $systems_primary->search_value ?>" /> <input type="submit" name="submit_search" value="Search Website" /> </form> <br /> </div> </div> <?php echo stripslashes($search_results); THE PHP: <?php // -- Begin Search -------------------------------------------------------------------------------------- if($_REQUEST["action"] === "search") { if(strlen($_REQUEST["pg"]) <= 0) { $_REQUEST["pg"] = 1; } $search_results = $systems_primary->search_website("index",urldecode($_REQUEST["search_value"]),"<div class=\"listing ui-corner-all\"><a href=\"{ENTRY_URL}\" title=\"{ENTRY_TITLE}\" class=\"listing_title\">{ENTRY_TITLE}</a>{ENTRY_CONTENT} <a href=\"{ENTRY_URL}\" title=\"{ENTRY_TITLE}\" style=\"font-size:.8em;\">...read more</a></div><br /><br />",345,"all",10,$_REQUEST["pg"]); } // -- End Search ---------------------------------------------------------------------------------------- ?> THE LOST CSS (could be more): html { background-color:#F6E6C8; font-size:16px; font:Helvetica; } body { width:1027px; margin:0 auto; background-color:#ffffff; font: arial, times new roman, sans-serif; }

Read the article
Missing Wireless access point

- by nvcnvn

I have an: Ubuntu 12.04 with proprietary Boardcom STA Wireless driver installed BCM43224 802.11a/b/g/n wireless card TP-LINK TD-W8101G 54Mbps Wireless ADSL2+ Modem Router Yesterday before I went to sleep, I still connect to my wireless access point, this morning when I start my laptop I don't see it in the list - there are some neighbors listed but not mine. The WLAN is green, with my old Nokia E72, I still see my access point with 100% signal. I have tried to restart my laptop and turn the firmware off/on by the switch but no help. I have read the WirelessTroubleShootingGuide but I can do anything. Here is some of my card info: *-network description: Wireless interface product: BCM43224 802.11a/b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: c0:cb:38:06:5d:53 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11abgn resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 03 serial: f0:4d:a2:42:ab:e4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168d-1.fw ip=192.168.1.3 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:5000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff memory:f0420000-f043ffff

Read the article
10.10 - No wired connection (cable plugged)

- by Roland Burda

So, my problem is that I have a recently bought laptop (Dell Inspiron M5040) with Ubuntu 10.10 installed on it, and the wired connection isn't working. The wireless connection is ok, it works. But the LAN isn't being recognized when the cable is plugged in. I've found an article, but I'm not sure whether it is a good approach for my case: http://www.zyxware.com/articles/2680/solved-wired-connection-eth0-not-detected-in-ubuntu-12-04

Read the article
Needs free/ opensource network monitoring tool for office LAN

- by Amit Ranjan

I know there must be a lot similar questions on SU. Let me explain my setup first. I have 4-5 PC, Laptops and Few Android Phones in my office. To get them on a network , I have a UTStarCom, WA3002G1 ADSL2+ router with a landline broadband connection which has nothing to do with any PC except the configuration settings. Broadband channel is always on, we need to switch on the router and the internet is ready for us. No Internet Connection sharing is done via any PC. I have a limited 20GB monthly plan, which is consumed in 10-20 days, depending upon the download requirements. So in the above case, i need some suggestions from you: How do I monitor my Internet Bandwidth along-with the connected systems, realtime? Any free opensource tool available? Tweaks / Changes in PC to save bandwidth as my ISP do not have any Unlimited plan. PC and Laptops are Windows XP and/Or windows 7. Either of the platform tools are welcome.

Read the article
Slow DNS Resolution

- by user4541

After a clean install of 10.10 I'm finding DNS resolution takes quite a long time. Hitting any url takes a good few seconds (10 - 30) before the site is displayed. I'm thinking this is a DNS resolution issue due to the 'waiting' or 'looking up' text being displayed in Firefox and Chrome. I do not get this issue with Slackware Linux or Windows 7 so it is not network or DNS server specific issue. It's something on the client side. Looking around on Google I see there are a few other people with this issue. The ones that have reported a workaround by switching to openDNS are disabling IPV6 or dealing with another issue. Any help would be appreciated. My network card is wired: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express Thanks

Read the article
IE6 Support - When to drop it? [closed]

- by Scott Brown

Possible Duplicate: Should I bother supporting IE6? I'm thinking about IE6 support and when to give up on it. Do you have a percentage of total visitors figure in mind for when to drop support? Would you let a trend develop past this figure or are you just going take the first opportunity? I've seen a 44% drop in IE6 visitors in the past 12 months from 23%(ish) of visitors down to 13%(ish). Even if it was 5% it still seems too early to drop support to me (it's still 1 in every 20 users). What are people's thoughts on this?

Read the article
How to setup a Wireless Access-Point using my laptop's WiFi card?

- by Abdul Karim Memon

want to share my Laptops (running Ubuntu 10.10) Broadband with my Android (Galaxy Mini) running 2.2.1. Since Androids currently do not support ad-hoc networks so the "Create new wireless network.." won't help. Q1) How do i setup a Wireless Access Point using my Laptops WiFi card? Q2) What is the difference between an "ad-hoc" network and an "access point"? **abdulkarim@aK-laptop**:~$ lspci | grep ireless 03:00.0 Network controller: Atheros Communications Inc. AR9287 Wireless Network Adapter (PCI-Express) (rev 01) iw list Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 7935 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-15 Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (20.0 dBm) (passive scanning) * 2472 MHz [13] (20.0 dBm) (passive scanning) * 2484 MHz [14] (disabled) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 Supported interface modes: * IBSS * managed * ** AP * AP/VLAN** * monitor * mesh point Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * Unknown command (55) * Unknown command (57) * Unknown command (59) * set_wiphy_netns * Unknown command (65) * connect * disconnect

Read the article
LinkSys router suddenly cannot get an IP address

- by user43208

I have a linksys router WRT54G2 connected to a cable broadband. Just last week, everything was working perfectly - I would be able to connect my laptop to the internet using WiFi. However, starting last week, I suddenly lost my internet connection. At first I thought something was wrong with my ISP. However, when I tried connecting the cable directly to my laptop, I found out that there was no problem with the internet connection after all. It appears that it is only my router that cannot get IP address. I have already tried cloning my MAC address and reconfiguring my router using the setup CD, but nothing worked. What could be the problem here? Thank you. Regards, Erwin

Read the article
Maximum file size for iFrame in IE7

- by Peter Turner

I've got a "super secure" javascript downloader* that I wrote, and it usually works alright. But I noticed, while trying to download a 90 meg file with it on a client's machine that on IE7, it's getting hung up about 1/3rd of the way through. I've never tried to send a file that large through the iFrame and it works fine in other browsers. Is there a size restriction on files that IE7 can read in an iFrame? * It's really just a PHP line that sets header("location: http://someplace/downloadbigthing.exe"); after it does some logging and verification.

Read the article
router cannot get ip address

- by user43208

Hi guys, I have a linksys router WRT54G2 connected to a cable broadband. Just last week, everything was working perfectly - I would be able to connect my laptop to the internet using WiFi. However, starting last week, I suddenly lost my internet connection. At first I thought something was wrong with my ISP. However, when I tried connecting the cable directly to my laptop, I found out that there was no problem with the internet connection after all. It appears that it is only my router that cannot get IP address. I have already tried cloning my MAC address and reconfiguring my router using the setup CD, but nothing worked. What could be the problem here? Thank you. Regards, Erwin

Read the article

< Previous Page | 77 78 79 80 81 82 83 84 85 86 87 88 | Next Page >