Search Results

Search found 3103 results on 125 pages for '01'.

Page 83/125 | < Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >

• Nvidia GT218 repository drivers don't work

  - by user1042840

  I upgraded all packages with sudo apt-get upgrade command on my Ubuntu 10.04 box and I have Ubuntu 12.04 3.2.0-29-generic-pae now. I have two monitors and the following GPU: 01:00.0 VGA compatible controller: NVIDIA Corporation GT218 [NVS 300] (rev a2) After upgrading to 12.04, I somehow lost my previous setup with one common workspace stretched across two monitors. When Ubuntu starts only one monitor is on. I can see the message on the active monitor: Not optimum mode. Recommended mode: 1680x1050 60Hz I used Nvidia proprietary drivers on 10.04 but now jockey-text --list shows: xorg:nvidia_current - NVIDIA accelerated graphics driver (Proprietary, Disabled, Not in use) xorg:nvidia_current_updates - NVIDIA accelerated graphics driver (post-release updates) (Proprietary, Enabled, Not in use) When I run sudo nvidia-settings it says You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run `nvidia-xconfig` as root), and restart the X server.' I typed nvidia-xconfig and rebooted, but jockey-text --list says the same after the reboot: Not in use. The same with nvidia-current - Enabled but Not in use. I also tried nvidia-173 but I ended up in tty immediately at startup so I removed it. I used to have some problems with Nvidia proprietary drivers on 10.04, I had to put paths to EDID files in /etc/X11/xorg.conf explicitly, but the resolution was as recommended and both monitors were working. If I understand correctly, nouveau drivers are used now by default because the resolution is still quite high, definitely not 800x600, xrandr showed: xrandr: Failed to get size of gamma for output default Screen 0: minimum 320 x 400, current 1600 x 1200, maximum 1600 x 1200 default connected 1600x1200+0+0 0mm x 0mm 1600x1200 66.0* 1280x1024 76.0 1024x768 76.0 800x600 73.0 640x480 73.0 640x400 0.0 320x400 0.0 1680x1050_60.00 (0x4f) 146.2MHz h: width 1680 start 1784 end 1960 total 2240 skew 0 clock 65.3KHz v: height 1050 start 1053 end 1059 total 1089 clock 60.0Hz However, colors seem a bit faded and blurry with nouveau drivers. Mouse cursor is invisible if it's placed inside Firefox window, and only one monitor is working. I like open source and if it's possible I'd prefer to use nouveau drivers but a few things should be fixed. I'm curious why nvidia-current drivers from the repository don't work now. I read it has something to do with the new X11 server in Ubuntu 12.04, is it true? How can I get it back to work?

  Read the article

• algorithm for project euler problem no 18

  - by Valentino Ru

  Problem number 18 from Project Euler's site is as follows: By starting at the top of the triangle below and moving to adjacent numbers on the row below, the maximum total from top to bottom is 23. 3 7 4 2 4 6 8 5 9 3 That is, 3 + 7 + 4 + 9 = 23. Find the maximum total from top to bottom of the triangle below: 75 95 64 17 47 82 18 35 87 10 20 04 82 47 65 19 01 23 75 03 34 88 02 77 73 07 63 67 99 65 04 28 06 16 70 92 41 41 26 56 83 40 80 70 33 41 48 72 33 47 32 37 16 94 29 53 71 44 65 25 43 91 52 97 51 14 70 11 33 28 77 73 17 78 39 68 17 57 91 71 52 38 17 14 91 43 58 50 27 29 48 63 66 04 68 89 53 67 30 73 16 69 87 40 31 04 62 98 27 23 09 70 98 73 93 38 53 60 04 23 NOTE: As there are only 16384 routes, it is possible to solve this problem by trying every route. However, Problem 67, is the same challenge with a triangle containing one-hundred rows; it cannot be solved by brute force, and requires a clever method! ;o) The formulation of this problems does not make clear if the "Traversor" is greedy, meaning that he always choosed the child with be higher value the maximum of every single walkthrough is asked The NOTE says, that it is possible to solve this problem by trying every route. This means to me, that is is also possible without! This leads to my actual question: Assumed that not the greedy one is the max, is there any algorithm that finds the max walkthrough value without trying every route and that doesn't act like the greedy algorithm? I implemented an algorithm in Java, putting the values first in a node structure, then applying the greedy algorithm. The result, however, is cosidered as wrong by Project Euler. sum = 0; void findWay(Node node){ sum += node.value; if(node.nodeLeft != null && node.nodeRight != null){ if(node.nodeLeft.value > node.nodeRight.value){ findWay(node.nodeLeft); }else{ findWay(node.nodeRight); } } }

  Read the article

• What are these errors when I try to "make" the driver of my wireless network?

  - by Tom Brito

  I got got a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme file say to use the "make" command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g

  Read the article

• Small hiccup with VMware Player after upgrading to Ubuntu 12.04

  The upgrade process Finally, it was time to upgrade to a new LTS version of Ubuntu - 12.04 aka Precise Pangolin. I scheduled the weekend for this task and despite the nickname of Mauritius (Cyber Island) it took roughly 6 hours to download nearly 2.400 packages. No problem in general, as I have spare machines to work on, and it was weekend anyway. All went very smooth and only a few packages required manual attention due to local modifications in the configuration. With the new kernel 3.2.0-24 it was necessary to reboot the system and compared to the last upgrade, I got my graphical login as expected. Compilation of VMware Player 4.x fails A quick test on the installed applications, Firefox, Thunderbird, Chromium, Skype, CrossOver, etc. reveils that everything is fine in general. Firing up VMware Player displays the known kernel mod dialog that requires to compile the modules for the newly booted kernel. Usually, this isn't a big issue but this time I was confronted with the situation that vmnet didn't compile as expected ("Failed to compile module vmnet"). Luckily, this issue is already well-known, even though with "Failed to compile module vmmon" as general reason but nevertheless it was very easy and quick to find the solution to this problem. In VMware Communities there are several forum threads related to this topic and VMware provides the necessary patch file for Workstation 8.0.2 and Player 4.0.2. In case that you are still on Workstation 7.x or Player 3.x there is another patch file available. After download extract the file like so: tar -xzvf vmware802fixlinux320.tar.gz and run the patch script as super-user: sudo ./patch-modules_3.2.0.sh This will alter the existing installation and source files of VMware Player on your machine. As last step, which isn't described in many other resources, you have to restart the vmware service, or for the heart-fainted, just reboot your system: sudo service vmware restart This will load the newly created kernel modules into your userspace, and after that VMware Player will start as usual. Summary Upgrading any derivate of Ubuntu, in my case Xubuntu, is quick and easy done but it might hold some surprises from time to time. Nonetheless, it is absolutely worthy to go for it. Currently, this patch for VMware is the only obstacle I had to face so far and my system feels and looks better than before. Happy upgrade! Resources I used the following links based on Google search results: http://communities.vmware.com/message/1902218#1902218http://weltall.heliohost.org/wordpress/2012/01/26/vmware-workstation-8-0-2-player-4-0-2-fix-for-linux-kernel-3-2-and-3-3/ Update on VMware Player 4.0.3 Please continue to read on my follow-up article in case that you upgraded either VMware Workstation 8.0.3 or VMware Player 4.0.3.

  Read the article

• Windows Azure Debugging: Matching an Instance in the DevFabric to its Process

  - by kaleidoscope

  Sometimes there may arise a need to match an instance one is watching in the Development Fabric UI back to its process. The following blog post explains the process to do the same: http://blogs.msdn.com/jnak/archive/2010/01/26/windows-azure-debugging-matching-an-instance-in-the-devfabric-to-its-process.aspx

  Read the article

• sony vaio WLAN problem using 12.04

  - by Fredrik

  I'm unable to get my WLAN to work for my Sony Vaio model VPCF23C5E No problem connecting from windows, smartphones etc. $ sudo lshw -C network; lsb_release -a; uname -a; sudo rfkill list; dmesg | grep -i firm *-network description: Wireless interface product: AR9485 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 64:27:37:92:99:0f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-29-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:16 memory:f7000000-f707ffff memory:f7080000-f708ffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 06 serial: f0:bf:97:dd:b2:bd size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-1.fw ip=192.168.1.4 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:50 ioport:9000(size=256) memory:e2104000-e2104fff memory:e2100000-e2103fff LSB Version: core-2.0-amd64:core-2.0-noarch:core-3.0-amd64:core-3.0-noarch:core-3.1-amd64:core-3.1-noarch:core-3.2-amd64:core-3.2-noarch:core-4.0-amd64:core-4.0-noarch Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise Linux siriedit 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no [ 1.287449] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 18.273582] [Firmware Bug]: ACPI(NGFX) defines _DOD but not _DOS Seen some proposed solution e.g. Wireless network cannot be enabled for Sony VAIO E series but answers there don't solve my problem... I'm out of ideas :-( What else can I check? update $ ifconfig -a eth0 Link encap:Ethernet HWaddr f0:bf:97:dd:b2:bd inet addr:192.168.1.4 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::f2bf:97ff:fedd:b2bd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5072 errors:0 dropped:0 overruns:0 frame:0 TX packets:4444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4568435 (4.5 MB) TX bytes:610624 (610.6 KB) Interrupt:50 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1498 errors:0 dropped:0 overruns:0 frame:0 TX packets:1498 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:114156 (114.1 KB) TX bytes:114156 (114.1 KB) wlan0 Link encap:Ethernet HWaddr 64:27:37:92:99:0f inet addr:192.168.1.5 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6627:37ff:fe92:990f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1277 errors:0 dropped:0 overruns:0 frame:0 TX packets:472 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:483155 (483.1 KB) TX bytes:61031 (61.0 KB)

  Read the article

• Fuji camera "mounts" but folder not in Dolphin After Kubuntu 13.10 upgrade

  - by user207207

  Fuji camera mount reported in attached devices but not visible in Dolphin After Kubuntu 13.10 upgrade Have reinstalled the driver, and a few other suggestions, for other cameras mounts failing on previous Ubuntu upgrades. I have already spent a couple of hours trying to get my photo's off the camera, very annoying. Worked perfectly in 11.04, 11.10, 12.04, 12.10 and 13.04. dmesg | tail; lsusb; lsb_release -a [ 6181.858786] CPUM: APIC 03 at 00000000fee00000 (mapped at ffffc90009400000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [17261.396236] CPUM: APIC 00 at 00000000fee00000 (mapped at ffffc90000c6a000) - ver 0x80050010, lint0=0x10700 lint1=0x00400 pc=0x00400 thmr=0x10000 [17261.396239] CPUM: APIC 03 at 00000000fee00000 (mapped at ffffc90000c72000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [17261.396241] CPUM: APIC 02 at 00000000fee00000 (mapped at ffffc90000c70000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [17261.396255] CPUM: APIC 01 at 00000000fee00000 (mapped at ffffc90000c6e000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [32456.884907] usb 2-5: new high-speed USB device number 2 using ehci-pci [32457.654046] usb 2-5: New USB device found, idVendor=04cb, idProduct=01e8 [32457.654050] usb 2-5: New USB device strings: Mfr=0, Product=2, SerialNumber=3 [32457.654052] usb 2-5: Product: Digital Camera [32457.654053] usb 2-5: SerialNumber: 4C3230302020091117CAA59WP18548 Bus 002 Device 002: ID 04cb:01e8 Fuji Photo Film Co., Ltd Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 2013:024f PCTV Systems nanoStick T2 290e Bus 001 Device 002: ID 046d:082d Logitech, Inc. HD Pro Webcam C920 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub No LSB modules are available. Distributor ID: Ubuntu vissibleDescription: Ubuntu 13.10 Release: 13.10 Codename: saucy sudo apt-get install gvfs-bin gvfs-mount gphoto2://[usb:002,002] Error mounting location: Error initializing camera: -108: No such file or directory ...... I have reported a bug in Dolphin, which has been transferred to Solid. Further information : I ran solid-hardware list details udi = '/org/kde/solid/udev/sys/devices/pci0000:00/0000:00:04.1/usb2/2-5' parent = '/org/kde/solid/udev' (string) vendor = '04cb' (string) product = 'Digital Camera' (string) description = 'Camera' (string) Block.major = 189 (0xbd) (int) Block.minor = 137 (0x89) (int) Block.device = '/dev/bus/usb/002/010' (string) Camera.supportedProtocols = {'ptp'} (string list) Camera.supportedDrivers = {'gphoto'} (string list) I still can't get my photo's off, I can see the folders using the Gimp menu. If anyone has got any ideas, I'm willing to try them.

  Read the article

• Second Monitor stays black/in power save mode

  - by Rob

  I'm using two Monitors, a Belinea o.display 1 (Recognized as a Rogen Tech Distribution Inc 20" by Ubuntu, but working fine) on the DVI-Output (connected via DVI-to-VGA-adapter) as my primary Monitor and a Dell 19" (Recognized correctly) on the HDMI-output (via HDMI-to-DVI adapter) as secondary monitor. The graphics controller is a GeForce 9500 GS. I'm running a fully updated Ubuntu 13.04 with nouveau 1:1.0.7-0ubuntu1. The problem is that the second monitor (Dell) never seems to come out of standby during boot: the screen stays black and the status led on the monitor stays orange (it's green when it's on). It is correctly recognized an the size of the desktop is set accordingly, it just stays black. Changing any setting via xrandr/arandr/etc. does nothing. The on-screen-menu of the monitor reports it to be in power save mode. When using the proprietary NVIDIA-Drivers, the second monitor works just find. But these drivers cause a lot of other problems on my system, so i would really like to avoid them. On Ubuntu 12.10 i had found a workaround: When moving the relative position of the second monitor slightly down and the up again, it would turn on and function normally: xrandr --output DVI-I-1 --mode 1680x1050 --pos 1280x0 --rotate normal --output HDMI-1 --mode 1280x1024 --pos 0x88 --rotate normal sleep 2 xrandr --output DVI-I-1 --mode 1680x1050 --pos 1280x0 --rotate normal --output HDMI-1 --mode 1280x1024 --pos 0x0 --rotate normal This workaround stop working after the update to 13.04, and now i'm looking for a new solution. Has anyone experienced something similarity? xrandr output: Screen 0: minimum 320 x 200, current 2960 x 1050, maximum 8192 x 8192 DVI-I-1 connected 1680x1050+0+0 (normal left inverted right x axis y axis) 433mm x 270mm 1680x1050 60.0*+ 1280x1024 75.0 60.0 1280x960 60.0 1152x864 75.0 1024x768 75.1 72.0 70.1 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 640x480 72.8 75.0 66.7 60.0 720x400 70.1 HDMI-1 connected 1280x1024+1680+0 (normal left inverted right x axis y axis) 376mm x 301mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 lshw -c video: *-display Beschreibung: VGA compatible controller Produkt: G96 [GeForce 9500 GS] Hersteller: NVIDIA Corporation Physische ID: 0 Bus-Informationen: pci@0000:01:00.0 Version: a1 Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress vga_controller bus_master cap_list rom Konfiguration: driver=nouveau latency=0 Ressourcen: irq:16 memory:fa000000-faffffff memory:d0000000-dfffffff memory:f8000000-f9ffffff ioport:df00(Größe=128) memory:fb000000-fb07ffff Thanks for your help!

  Read the article

• Wireless connection by using command screen

  - by Amadeus

  I installed Ubuntu 12.04 armhf to my beagleboard-xm and now trying to connect to a wireless network. First, I checked if I can search for available networks: ubuntu@arm:~$ iwlist scan lo Interface doesn't support scanning. usb0 Interface doesn't support scanning. wlan0 Scan completed : Cell 01 - Address: EA:7D:EF:60:C9:0B Channel:1 Frequency:2.412 GHz (Channel 1) Quality=70/70 Signal level=-23 dBm Encryption key:on ESSID:"ghostrider" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Ad-Hoc Extra:tsf=000000005a1ab50e Extra: Last beacon: 6242ms ago IE: Unknown: 000A67686F73747269646572 IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 06020000 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: Unknown: 32040C121860 IE: Unknown: 2D1A2C181BFF00000000000000000000000000000000000000000000 IE: Unknown: 3D16010800000000FF000000000000000000000000000000 IE: Unknown: DD09001018020000000000 Then I edited /etc/network/interfaces file to the following: root@arm:/etc/wpa_supplicant# cat /etc/network/interfaces auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # Example to keep MAC address between reboots #hwaddress ether DE:AD:BE:EF:CA:FE # WiFi Example auto wlan0 iface wlan0 inet dhcp wpa-ssid "ghostrider" wpa-psk "b34d373eb2fb836a43b0afffe783c7d0af694724506c9e77b06d1021302905bf" But I cannot still connect to the wireless network: root@arm:/etc/wpa_supplicant# iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Asociated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on eth0 no wireless extensions. root@arm:/etc/network# ifup wlan0 Failed to bring up wlan0. What is wrong? Should I change any other files also? But I think it was enough. By the way if you are curious about where that wpa-psk came from: zero@ghostrider:~$ wpa_passphrase ghostrider 34bddf67c2 network={ ssid="ghostrider" #psk="34bddf67c2" psk=b34d373eb2fb836a43b0afffe783c7d0af694724506c9e77b06d1021302905bf } I will appreciate any effort to help. Regards, Amadeus ps: Also I tried to connect manually: root@arm:/etc/network# iwconfig wlan0 essid ghostrider key s:34bddf67c2 But this did not solve my problem also.

  Read the article

• Cannot boot normally, without restarting lightdm (or gdm)

  - by leventov

  I had a problem precisely described here: http://www.webupd8.org/2013/01/ubuntu-lightdm-black-screen-when-using.html, black screen with blinking cursor instead of login screen. I've switched to gdm using sudo dpkg-reconfigure gdm -- but faced the same problem, now loading process stops on "red-white Ubuntu dots" (without activity under this splash). And to login, I still need to restart display manager: Ctrl+Alt+F1 and sudo service gdm restart. How to make Ubuntu to boot normally?

  Read the article

• Toshiba wireless is blocked

  - by zorrillo

  I have the same problem, a 32 bits toshiba nb255, it first had the windows 7 bu next I installed the ubuntu 11.04. The wifi does not turn on. I used the following issues the commands rfkill unblock wlan0, sudo ifconfig wlan0 down; they were not able. by setting up the bios in advanced menu, the wireless communication sw in ON, but it did not work also. neither the utilities toshiba nor utilities of ubuntu (wicd, wifi radar). by using gedit to file group, nothing. by installing madwifi packet, nothing. by exporting the wifi driver from windows to ubuntu, by means of the NDISwrapper packet, neither. I put the current scripts of the ouput of the cli root@zorrillo:~# rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes root@zorrillo:~# sudo lspci | grep Atheros 07:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) root@zorrillo:~# root@zorrillo:~# ifconfig -a eth0 Link encap:Ethernet direcciónHW 88:ae:1d:47:df:e1 ACTIVO DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) Interrupción:43 Dirección base: 0xe000 lo Link encap:Bucle local Direc. inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:16436 Métrica:1 Paquetes RX:8 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:8 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:480 (480.0 B) TX bytes:480 (480.0 B) ppp0 Link encap:Protocolo punto a punto Direc. inet:189.203.115.236 P-t-P:192.168.226.1 Másc:255.255.255.255 ACTIVO PUNTO A PUNTO FUNCIONANDO NOARP MULTICAST MTU:1500 Métrica:1 Paquetes RX:6384 errores:30 perdidos:0 overruns:0 frame:0 Paquetes TX:6893 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:3 Bytes RX:5473081 (5.4 MB) TX bytes:974316 (974.3 KB) wlan0 Link encap:Ethernet direcciónHW 00:26:4d:c3:d0:44 DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) note.-it is logical all the counters are cero if the wireless device is down root@zorrillo:/home/zorrillo/Descargas/802BGA# ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill root@zorrillo:/home/zorrillo/Descargas/802BGA# It would seem the wireless switching does not react with whichever ubuntu 11.04 command (I hope to be wrong). The target remains the same, in order of the scripts above. I am worried, I have tried to find any answer for days and nights. Toshiba does not supply drivers or soft support for linux, marketing of course. I only see the device is up by protocols and down phisically, My question is, is it possible to enable or not shutdown physically the device?, because in the toshiba model nb255 the wifi is not set up/down bye means of a physical switch, but by means a combination of Fn + F8 (only for windows 7, no one more), Is there one possibility to configure the hot keys in ubuntu?

  Read the article

• After startup, display reverts to one desktop duplicated on both screens

  - by Skilldrick

  I have a Samsung R530 laptop. I'm actually running Linux Mint, which is based on Ubuntu (which is why I thought it would be OK to post this here). I'm now getting exactly the same problem on Ubuntu 10.10. I've got it setup with a secondary LCD monitor, and I've changed the display settings so the laptop screen and monitor are at optimal resolution, with the desktop shared between them. After startup though (typically around 10-30 seconds) the display reverts to 1024 x 768 on both screens, and the display is duplicated (i.e. both screens show the same thing). I think this is something to do with my video card, as I had the same problem when I was running Arch Linux. Any ideas? Edit: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 09) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 09) 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller It seems it's Intel, not Nvidia. I have a current work around, which is to have a launcher to a script containing xrandr --output LVDS1 --mode 1366x768 --output HDMI1 --mode 1280x1024 --left-of LVDS1 on my desktop, and to run it after the displays revert, but it's not ideal.

  Read the article

• Can my machine run Ubuntu( kubuntu | xubuntu | mint ) 12.04 WELL?

  - by Steve

  I have a 9 year old computer packing the hardware listed below. My question is, can I run 12.04 ( Ubuntu, Kubuntu, MINT or Xubuntu ) WELL? I was running Ubuntu 10.10 and I upgraded to 12.04 by going through each release via the update manager: 11.04 - 11.10 -12.04 During the installation process for 12.04 I saw an error message that there was an error installing and setting up part of the kernel. Later, when I tried installing a package in synaptic, I got another error message mentioning the kernel. When I rebooted, I got told somehting about my video and graphics was not configured properly and that I would have to do it manually ( like I know ). It gave me the option to enter the system in low graphics mode, but it just hanged. I had an old livecd of Xubuntu 10.10 around so I used that to get into my computer and copy data over to an external hard drive. I think tried to install Xubuntu 10.10 from the livecd, with the option "download updates" checked. The install process moved along a bit, then halted for about 5 hours. I rebooted my machine and tried the Xubuntu 10.10 installer WITHOUT the option to "download updates". The install completed in about 15 minutes. So, all of that is making me wonder if there is someting about 12.04 that does not like my hardware. I'm willing to try again, but only if I know I will not have to spend hours just to get to an error message and a hosed up system like I did last night. I also think I have a lot more RAM than is being reported in the output below. I had extra ram installed last year. I'm not good with the command line readouts, but there seems like there should be a lot more. I wasn't thrilled with Unity. I am willing to try Kubuntu 12.04. Will I run into the same problems? What is the highest version of a *ubuntu can I upgrade to? Thanks CPU Model: Intel(R) Pentium(R) 4 CPU 2.53GHz Frequency: 2533.223 MHz L2 Cache: 512 KB Bogomips: 5066.44 Numbering: family(15) model(2) stepping(7) Flags: fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe up pebs bts cid RAM ~$ free -mt total used free shared buffers cached Mem: 1506 891 615 0 91 521 -/+ buffers/cache: 278 1227 Swap: 1609 0 1609 Total: 3116 891 2225 Video Card 01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev a2) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. V9180 Magic Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 16 Memory at fd000000 (32-bit, non-prefetchable) [size=16M] Memory at f0000000 (32-bit, prefetchable) [size=64M] Expansion ROM at fe9e0000 [disabled] [size=128K] Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb Motherboard Intel 845PE ATX 533FSB DDR333 USB2

  Read the article

• Ubuntu 14.04 and Android, can't see phone on my computer

  - by user3527983

  I have installed gMTP and tried to follow this tutorial to solve this problem: http://www.webupd8.org/2013/01/upgrade-to-gvfs-with-mtp-support-in.html But neither worked. I tried to connect both my phone (Nexus 4) and my dad's phone (Galaxy Note 2), and neither is being detected by Ubuntu. They don't show up on my files and on gMTP. Is there another fix? or something more specific for Android 4.3 and Ubuntu 14.04

  Read the article

• Data Compare is Finally Back in VS 2012

  - by Aligned

  Originally posted on: http://geekswithblogs.net/Aligned/archive/2013/07/01/data-compare-is-finally-back-in-vs-2012.aspxI’ve been missing the data compare tool this since moving from VS 2010. I’ve install the VS 2013 v3 update and then the SQL Server Data Tools - June 2013 update. I don’t think v3 is required, but it’s a good upgrade to do anyways. http://blogs.msdn.com/b/ssdt/archive/2013/06/24/announcing-sql-server-data-tools-june-2013.aspx

  Read the article

• ???? ????? ????? ?????? ????? 10.2.0.4

  - by gadi.chen

  Normal 0 false false false EN-US X-NONE HE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif";} DBA's ?????? ?????? ???? ??? ????? ??? ?????? ???? ????? ????? ??? ?????. ??? ????? ???? ????? ???? ??????? 30-Apr-2011  ???? ???? ?????? ????? ???? ??????? 10.2.0.4. ?????? ????? EBS ?? ????? ????? ????? ????? ??? ??? ???? ????? ?????? extended support, ???? ???? 11.5.10.2 ??? ???? ? 01-Dec-2011 . ) ????? ?????? ????  Minimum Baseline For Extended Support ????? ?????: 883202.1) ???? ????? ????? ?????? ?????? ?? ????? ????? ????? ????????? ???? ?? :   # ATG.RUP6 # Forms6i Patchset 19 # JRE 1.6.0_03       ???? ???? ?????? EBS ?? ????? ?????? ?????? ????? ???? ?????? ?? ,?? ??? ????? ?? ???? ??????.   ????? ???? 10.2.0.4 ?? ???? ?patches ????? ????  30-Apr-2011 . ???? ????  patches ????? ?? ????? ????? 10.2.0.5   .   ???? ????? EBS ????? 3 ?????? ?????? ?? ???: 1.      ????? ????? 11.2.0.2 - ??? ???? ????? ??????? ?????? ??? EBS ??????? 11i   ? R12 2.      ????? ????? 11.1.0.7 -  ??? ???? ????? ?????? ????? ????? 11.1 ??? ?????. 3.      ?????/????? patch 10.2.0.5 -   ???? ????? ?????? ????? ?????? ????? 10gR2 . v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 false false false false EN-US X-NONE HE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif";}   ?????? ??????? ???? ??????:     http://blogs.oracle.com/stevenChan/2011/01/ecs_10gr2_10204.html On Database Patching and Support: A Primer for E-Business Suite Users Oracle Database 10.2 End of Premier Support -- Frequently Asked Questions (Note 1130327.1)        

  Read the article

• SQL Server 2008 R2 Quiet Installation Failure

  - by pk

  I've downloaded the SQL Server 2008 R2 software from Microsoft and am working on scripting a silent installation. I'm getting the following errors (and the duplicate paste job is not an accident, that's how it shows up for me) The following error occurred: Exception has been thrown by the target of an invocation. Error result: 1152035024 Result facility code: 1194 Result error code: 43216 Please review the summary.txt log for further details The following error occurred: Exception has been thrown by the target of an invocation. Error result: 1152035024 Result facility code: 1194 Result error code: 43216 Please review the summary.txt log for further details Microsoft (R) SQL Server 2008 R2 Setup 10.50.1600.01 This is what shows up in the detailed SQL install log. 2011-02-23 09:53:13 Slp: Running Action: ExecuteInitWorkflow 2011-02-23 09:53:13 Slp: Workflow to execute: 'INITIALIZATION' 2011-02-23 09:53:13 Slp: Error: Action "Microsoft.SqlServer.Configuration.BootstrapExtension.ExecuteWorkflowAction" threw an exception during execution. 2011-02-23 09:53:13 Slp: Microsoft.SqlServer.Setup.Chainer.Workflow.ActionExecutionException: Exception has been thrown by the target of an invocation. ---> System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> System.ArgumentNullException: Value cannot be null. 2011-02-23 09:53:13 Slp: Parameter name: InstallMediaPath Hopefully someone can help me work through this. Here is a simple version of my PowerShell code. $arguments = @() $arguments += "/q" $arguments += "/ACTION=Install" $arguments += "/FEATURES=SQL,Tools" $arguments += "/INSTANCENAME=MSSQLSERVER" $arguments += "/SQLSVCACCOUNT=`"$NetBIOSDomainName\$SQLServerServiceAccount`"" $arguments += "/SQLSVCPASSWORD=`"$SQLServerServiceAccountPassword`"" $arguments += "/SQLSYSADMINACCOUNTS=`"$NetBIOSDomainName\$SQLSysAdminAccount`"" $arguments += "/AGTSVCACCOUNT=`"$NetBIOSDomainName\$SQLServerAgentAccount`"" $arguments += "/IACCEPTSQLSERVERLICENSETERMS" Start-Process "$SQLServerSetupLocation\setup.exe" -Wait -ArgumentList $arguments -RedirectStandardOutput error.txt

  Read the article

• Windows Server 2008 R2 Server Manager not working -> mmc.exe crashes with System.IO.FileNotFoundException

  - by Aleja_Vigo

  Since some days ago I can't run the Server Manager, it fails like this: Descripción: Stopped working Firma con problemas: Nombre del evento de problema: CLR20r3 Firma del problema 01: mmc.exe Firma del problema 02: 6.1.7600.16385 Firma del problema 03: 4a5bc808 Firma del problema 04: System.Management Firma del problema 05: 2.0.0.0 Firma del problema 06: 4ca2baf0 Firma del problema 07: 32f Firma del problema 08: 12b Firma del problema 09: System.IO.FileNotFoundException Versión del sistema operativo: 6.1.7601.2.1.0.272.7 There are other strange syntoms in the SO: Hyper-V stopped working as well, fails to load any VM information The desktop icons rearrange themselves all the time, and always on boot, after I move them. I use now an app that remembers their position to restore it... Windows Update service dissapeared, along with BITS service, I managed to recover them and installed all updates availables today I'm going nuts looking for information about these errors. Solutions that didn't work: sfc /scannow Doesn't complain about anything All windows updates applied (after recovering missing Windows Update) ServerManager.log: Only one error all the time: Error (Id=0) System.Runtime.InteropServices.COMException (0x800706D9): No hay más extremos disponibles desde el asignador de extremos. (Excepción de HRESULT: 0x800706D9) en Microsoft.Windows.ServerManager.NativeMethods.INetFwPolicy2.IsRuleGroupCurrentlyEnabled(String group) en Microsoft.Windows.ServerManager.DirectResult.GetRemoteManagementEnabled() In english : "There are no more endpoints available from the endpoint mapper" Where could I see which is the infamous file that mmc.exe is looking for in that System.IO.FileNotFoundException?? Please, any light on this would be much appreciated...

  Read the article

• Unable to Install SQL Server on Server 2012

  - by Jeff

  The problem I have been trying to install SQL Server 2012 on Windows Server 2012. I continually get the same error: Managed SQL Server Installer has stopped working Problem signature: Problem Event Name: CLR20r3 Problem Signature 01: scenarioengine.exe Problem Signature 02: 11.0.3000.0 Problem Signature 03: 5081b97a Problem Signature 04: Microsoft.SqlServer.Chainer.Setup Problem Signature 05: 11.0.3000.0 Problem Signature 06: 5081b97a Problem Signature 07: 18 Problem Signature 08: 0 Problem Signature 09: System.IO.FileLoadException OS Version: 6.2.9200.2.0.0.272.79 Locale ID: 1033 Additional Information 1: c319 Additional Information 2: c3196e5863e32e0baf269d62f56cbc70 Additional Information 3: 422d Additional Information 4: 422d950c58f4efd1ef1d8394fee5d263 What I've tried After initial googling, I've tried the following things: Go through the list of hardware and software pre-reqs. All the software seems to be there by default on Server 2012 and my hardware meets the reqs. Copy the installation media to the local drive and try to install from that (rather than a DVD). This produced the same error. Based on another error message, I installed .NET 4.0 (which apparently is not on Server 2012 out of the box). Same error. Install from command line. This didn't work either, but it gave me a different error: Error: Unhandled Exception: System.IO.FileLoadException: Could not load file or assembl y 'Microsoft.SqlServer.Configuration.Sco, Version=11.0.0.0, Culture=neutral, Pub licKeyToken=89845dcd8080cc91' or one of its dependencies. Strong name validation failed. (Exception from HRESULT: 0x8013141A) ---> System.Security.SecurityExcep tion: Strong name validation failed. (Exception from HRESULT: 0x8013141A) --- End of inner exception stack trace --- at Microsoft.SqlServer.Chainer.Infrastructure.InputSettingService.CheckForBoo leanInputSettingExistenceFromCommandLine(ServiceContainer context, String settin gName) at Microsoft.SqlServer.Chainer.Setup.Setup.DebugBreak(ServiceContainer contex t) at Microsoft.SqlServer.Chainer.Setup.Setup.Main() Any ideas what I am missing?

  Read the article

• Intermittent Windows Server 2008 BSOD and restart

  - by Timka

  Our EC2 Instance (Windows Server 2008) crashed multiple times for the past 3 months (last time was today at 1:05 EST). Upon reviewing MEMORY.DMP file we noticed that possible cause of the crashes is rhelnet.sys (RedHat PV NIC Driver). Server's Event Viewer has the following records right after the crash: Critical - Kernel Power: The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. BugCheck: The computer has rebooted from a bugcheck. The bugcheck was: 0x000000d1 (0x000000000000002d, 0x0000000000000002, 0x0000000000000000, 0xfffff88001402d14). A dump was saved in: C:\Windows\MEMORY.DMP. Report Id: 100113-35849-01. Could this be a hardware issue? Would it help if we stop and start the instance? Or is this more likely that this is caused by the software running on the system? [Update 10.01.2013] Amazon Rep suggested to update RH drivers to Citrix PV drivers on our instance: Upgrading PV Drivers [Update 10.08.2013] We performed a drivers upgrade on the cloned instance. Right after the upgrade we noticed the following errors in our Event viewer: Xennet6 errors in Event Viewer (Event ID# 5001) After digging a bit more I found this article suggesting to install the latest Citrix drivers. Unfortunately, this didn't help us at all and our cloned instance became unresponsive. [Update 10.08.2013 2] I recreated an instance and updated PV drivers again. After searching on Internet I found this article where Amazon Rep explains that: "Event ID 5001 from source Xennet6 cannot be found" message does not indicate anything wrong, just that the PV driver is looking for a feature that we have not implemented in our version of Xen. I will keep my test system running for a while to see if there any issues with it.

  Read the article

• vCenter appliance won't use mail relay server

  - by Safado

  tl;dr: - sendmail is configured to use a relay server but still insists on using 127.0.01 as the relay, which results in mail not being sent. We have the open source vCenter appliance (v 5.0) managing our ESXi cluster. When connected to it via vSphere Client, you can configure the SMTP relay server to use by going to Administration > vCenter Server Settings > MAIL. There you can set the SMTP Server value. I looked through their documentation and also confirmed on the phone with support that all you have to do to configure mail is to put in the relay IP or fqdn in that box and hit OK. Well, I had done that and mail still wasn't sending. So I SSH into the server (which is SuSE) and look at /var/log/mail and it looks like it's trying to relay the email through 127.0.0.1 and it's rejecting it. So looking through the config files, I see there's /etc/sendmail.cf and /etc/mail/submit.cf. You can configure items in /etc/sysconfig/sendmail and run SuSEconfig --module sendmail to generate those to .cf files based on what's in /etc/sysconfig/sendmail. So playing around, I see that when you set the SMTP Server value in the vCenter gui, all that it does is change the "DS" line in /etc/mail/submit.cf to have DS[myrelayserver.com]. Looking on the internet, it would appear that the DS line is really the only thing you need to change in order to use a relay server. I got on the phone with VMWare support and spent 2 hours trying to modify ANY setting that had anything to do with relays and we couldn't get it to NOT use 127.0.0.1 as the relay. Just to note, any time we made any sort of configuration change, we restarted the sendmail service. Does anyone know whats going on? Have any ideas on how I can fix this?

  Read the article

• IIS 7 returns 304 instead of 200

  - by Ola Herrdahl

  I have a strange issue with IIS 7. Sometimes it seems to return a 304 instead of a 200. Here is a sample request captured with Fiddler: (Note that the file requested is not located in my browsers cache yet.) GET https://[mysite]/Content/js/jquery.form.js HTTP/1.1 Accept: */* Referer: https://[mysite]/Welcome/News Accept-Language: sv-SE User-Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; WOW64; Trident/4.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; InfoPath.2; OfficeLiveConnector.1.4; OfficeLivePatch.1.3; .NET4.0C; .NET4.0E) Accept-Encoding: gzip, deflate Host: [mysite] Connection: Keep-Alive Cache-Control: no-cache Cookie: ... Note that there is no If-Modified-Since or If-None-Match in the request. But still the response is: HTTP/1.1 304 Not Modified Cache-Control: public Expires: Tue, 02 Mar 2010 06:26:08 GMT Last-Modified: Mon, 22 Feb 2010 21:58:44 GMT ETag: "1CAB40A337D4200" Server: Microsoft-IIS/7.5 X-Powered-By: ASP.NET Date: Mon, 01 Mar 2010 17:06:34 GMT Does anyone have a clue of what could be wrong here? I'm running IIS 7 on Windows Web Server 2008 R2.

  Read the article

• How to resolve Windows Update Error 8024402F on Windows 7 Home Premium 64bit?

  - by Day

  I have been having the same problem with Windows Updates on 2 of my machines at home, both running Windows 7 Home Premium 64-bit. One of the 2 machines is a brand new install, the other has run Windows Update in the past, but is also not working now. When I manually check for updates using the Control Panel, I get error code 8024402F: I followed the link to "Get help with this error", which brings up several articles in Windows Help and Support, none of which are for this specific error code. From the help and general googling I've tried: Checking internet connectivity. Most of the help suggests that this error is caused by a general internet connectivity problem. But if you're reading this, my connection is definitely working fine. Disabling antivirus temporarily and trying to run Windows Update. This didn't help (I run AVG free) Running Control Panel - Troubleshooting - Security Systems - Fix Problems with Windows Update. This said it detected and resolved problems, but didn't help. Update using IE (as I used to in XP). Go to http://windowsupdate.microsoft.com/ redirects me to http://test.update.microsoft.com/windowsupdate/v6/vistadefault.aspx for which IE displays a "connection problem" (i.e. site unreachable) I've had the same problem for 24 hours now, so surely the Windows Update servers haven't been down this whole time? A quick check on twitter shows no worldwide outcry about Windows Update being unavailable, so is it just me? I'm based in the UK, but I notice that the http://test.update.microsoft.com/windowsupdate/v6/vistadefault.aspx URL is also unavailable using ''wget'' from my webserver in Chicago. day@ord1:~$ wget http://test.update.microsoft.com/windowsupdate/v6/vistadefault.aspx --2011-03-17 00:01:27-- http://test.update.microsoft.com/windowsupdate/v6/vistadefault.aspx Resolving test.update.microsoft.com... failed: Name or service not known. wget: unable to resolve host address `test.update.microsoft.com' day@ord1:~$ host test.update.microsoft.com Host test.update.microsoft.com not found: 3(NXDOMAIN)

  Read the article

• Linux e1000e (Intel networking driver) problems galore, where do I start?

  - by Evan Carroll

  I'm currently having a major problem with e1000e (not working at all) in Ubuntu Maverick (1.0.2-k4), after resume I'm getting a lot of stuff in dmesg: [ 9085.820197] e1000e 0000:02:00.0: PCI INT A disabled [ 9089.907756] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k4 [ 9089.907762] e1000e: Copyright (c) 1999 - 2009 Intel Corporation. [ 9089.907797] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9089.907827] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9089.907857] e1000e 0000:02:00.0: setting latency timer to 64 [ 9089.908529] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9089.908922] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9089.908954] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9090.024625] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9090.024630] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9090.024712] e1000e 0000:02:00.0: eth0: MAC: 2, PHY: 2, PBA No: 005302-003 [ 9090.109492] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9090.164219] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X and, a bunch of [ 2128.005447] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang: [ 2128.005452] TDH <89> [ 2128.005454] TDT <27> [ 2128.005456] next_to_use <27> [ 2128.005458] next_to_clean <88> [ 2128.005460] buffer_info[next_to_clean]: [ 2128.005463] time_stamp <6e608> [ 2128.005465] next_to_watch <8a> [ 2128.005467] jiffies <6f929> [ 2128.005469] next_to_watch.status <0> [ 2128.005471] MAC Status <80080703> [ 2128.005473] PHY Status <796d> [ 2128.005475] PHY 1000BASE-T Status <4000> [ 2128.005477] PHY Extended Status <3000> [ 2128.005480] PCI Status <10> I decided to compile the latest stable e1000e to 1.2.17, now I'm getting: [ 9895.678050] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.17-NAPI [ 9895.678055] e1000e: Copyright(c) 1999 - 2010 Intel Corporation. [ 9895.678098] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9895.678129] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9895.678162] e1000e 0000:02:00.0: setting latency timer to 64 [ 9895.679136] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.679160] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9895.679192] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9895.791758] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9895.791766] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9895.791850] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 2, PBA No: 005302-003 [ 9895.892464] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.948175] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.949111] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9895.954694] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: RX/TX [ 9895.954703] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO [ 9895.955157] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9906.832056] eth0: no IPv6 routers present With 1.2.20 I get: [ 9711.525465] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.20-NAPI [ 9711.525472] e1000e: Copyright(c) 1999 - 2010 Intel Corporation. [ 9711.525521] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9711.525554] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9711.525586] e1000e 0000:02:00.0: setting latency timer to 64 [ 9711.526460] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9711.526487] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9711.526523] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9711.639763] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9711.639771] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9711.639854] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 2, PBA No: 005302-003 [ 9712.060770] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9712.116195] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9712.117098] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9712.122684] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX [ 9712.122693] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO [ 9712.123142] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9722.920014] eth0: no IPv6 routers present But, I'm still getting these [ 9982.992851] PCI Status <10> [ 9984.993602] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang: [ 9984.993606] TDH <5d> [ 9984.993608] TDT <6b> [ 9984.993611] next_to_use <6b> [ 9984.993613] next_to_clean <5b> [ 9984.993615] buffer_info[next_to_clean]: [ 9984.993617] time_stamp <24da80> [ 9984.993619] next_to_watch <5d> [ 9984.993621] jiffies <24f200> [ 9984.993624] next_to_watch.status <0> [ 9984.993626] MAC Status <80080703> [ 9984.993628] PHY Status <796d> [ 9984.993630] PHY 1000BASE-T Status <4000> [ 9984.993632] PHY Extended Status <3000> [ 9984.993635] PCI Status <10> [ 9986.001047] e1000e 0000:02:00.0: eth0: Reset adapter [ 9986.176202] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: RX/TX [ 9986.176211] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO I'm not sure where to start troubleshooting this. Any ideas? Here is the result of ethtool -d eth0 MAC Registers ------------- 0x00000: CTRL (Device control register) 0x18100248 Endian mode (buffers): little Link reset: reset Set link up: 1 Invert Loss-Of-Signal: no Receive flow control: enabled Transmit flow control: enabled VLAN mode: disabled Auto speed detect: disabled Speed select: 1000Mb/s Force speed: no Force duplex: no 0x00008: STATUS (Device status register) 0x80080703 Duplex: full Link up: link config TBI mode: disabled Link speed: 10Mb/s Bus type: PCI Express Port number: 0 0x00100: RCTL (Receive control register) 0x04048002 Receiver: enabled Store bad packets: disabled Unicast promiscuous: disabled Multicast promiscuous: disabled Long packet: disabled Descriptor minimum threshold size: 1/2 Broadcast accept mode: accept VLAN filter: enabled Canonical form indicator: disabled Discard pause frames: filtered Pass MAC control frames: don't pass Receive buffer size: 2048 0x02808: RDLEN (Receive desc length) 0x00001000 0x02810: RDH (Receive desc head) 0x00000001 0x02818: RDT (Receive desc tail) 0x000000F0 0x02820: RDTR (Receive delay timer) 0x00000000 0x00400: TCTL (Transmit ctrl register) 0x3103F0FA Transmitter: enabled Pad short packets: enabled Software XOFF Transmission: disabled Re-transmit on late collision: enabled 0x03808: TDLEN (Transmit desc length) 0x00001000 0x03810: TDH (Transmit desc head) 0x00000000 0x03818: TDT (Transmit desc tail) 0x00000000 0x03820: TIDV (Transmit delay timer) 0x00000008 PHY type: IGP2 and ethtool -c eth0 Coalesce parameters for eth0: Adaptive RX: off TX: off stats-block-usecs: 0 sample-interval: 0 pkt-rate-low: 0 pkt-rate-high: 0 rx-usecs: 3 rx-frames: 0 rx-usecs-irq: 0 rx-frames-irq: 0 tx-usecs: 0 tx-frames: 0 tx-usecs-irq: 0 tx-frames-irq: 0 rx-usecs-low: 0 rx-frame-low: 0 tx-usecs-low: 0 tx-frame-low: 0 rx-usecs-high: 0 rx-frame-high: 0 tx-usecs-high: 0 tx-frame-high: 0 Here is also the lspci -vvv for this controller 02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller Subsystem: Lenovo ThinkPad X60s Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 45 Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 2000 [size=32] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0300c Data: 415a Capabilities: [e0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [140 v1] Device Serial Number 00-0a-e4-ff-ff-3e-ce-74 Kernel driver in use: e1000e Kernel modules: e1000e I filed a bug on this upstream, still no idea how to get more useful information. Here is a the result of the running that script EEPROM FIX UPDATE $ sudo bash fixeep-82573-dspd.sh eth0 eth0: is a "82573L Gigabit Ethernet Controller" This fixup is applicable to your hardware Your eeprom is up to date, no changes were made Do I still need to do anything? Also here is my EEPROM dump $ sudo ethtool -e eth0 Offset Values ------ ------ 0x0000 00 0a e4 3e ce 74 30 0b b2 ff 51 00 ff ff ff ff 0x0010 53 00 03 02 6b 02 7e 20 aa 17 9a 10 86 80 df 80 0x0020 00 00 00 20 54 7e 00 00 14 00 da 00 04 00 00 27 0x0030 c9 6c 50 31 3e 07 0b 04 8b 29 00 00 00 f0 02 0f 0x0040 08 10 00 00 04 0f ff 7f 01 4d ff ff ff ff ff ff 0x0050 14 00 1d 00 14 00 1d 00 af aa 1e 00 00 00 1d 00 0x0060 00 01 00 40 1f 12 07 40 ff ff ff ff ff ff ff ff 0x0070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff 4a e0 I'd also like to note that I used eth0 every day for years and until recently never had an issue.

  Read the article

• Windows Backup failed as another backup or recovery is in progress.

  - by remunda

  Hi, i have set up backup schedule on our server. SQL Server 2008 to 01:00am on windows server 2008 R2 to 4:00am. Sql backup runs well, but system backup ends sometimes with error. The error is : http://technet.microsoft.com/en-us/library/dd364768%28WS.10%29.aspx I mean, that is caused by SQL Server, because it unexpectedly runs backup. this is from sql server log (it runs for every database): Date 4.2.2010 4:00:21 Log SQL Server (Current - 29.1.2010 23:25:00) Source spid72 Message I/O is frozen on database master. No user action is required. However, if I/O is not resumed promptly, you could cancel the backup. and Date 4.2.2010 4:00:24 Log SQL Server (Current - 29.1.2010 23:25:00) Source Backup Message Database backed up. Database: master, creation date(time): 2010/01/29(23:25:32), pages dumped: 370, first LSN: 859:56:37, last LSN: 859:80:1, number of dump devices: 1, device information: (FILE=1, TYPE=VIRTUAL_DEVICE: {'{17B91D5C-9968-4D11-A7F1-1A31523D32F0}25'}). This is an informational message only. No user action is required. My questions is: Why runs sql backup with windows backup? How can i dissolve this that errors? Thank you a lot.

  Read the article

< Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >