duplex printing - Page 83

Ubuntu in failed state after upgrade from 10.04 to 10.10 - How to recover?

- by Harvey

I was running Ubuntu 10.04 and attempted to upgrade to 10.10. I have a really slow connection (DSL 128kbits/sec) and copying the upgrade files took about 26 hours. I of course let it run unattended. When I came back, I notice the following 3 dlgs: 1. Could not install the upgrades The upgrade has aborted. Your system could be in an unusable state. A recovery will run now (dpkg -- configure -a). 2. gpk-update-icon Distribution upgrades available maverick 10.10 (stable) [more information] [Do no show this again] [Cancel] [Ok] 3. gpk-update-icon Security updates available The following important updates are available for your computer: libwebkit-1.0-2-dbg - Web content engine library for Gtk+ - Debugging symbols libcupsimage2 - Common UNIX Printing System(tm) - Raster image library ... What is the best response to all of this? I went through something similar in an attempted network upgrade from 8.04 to 10.04 and had to reload the unbootable machine fresh from distribution media (all data was lost). I'd like to avoid that here. I have not yet responded to the dialogs, and want to make sure the system is still bootable and not lose my data this time.

Read the article

RHEL 5.3 Kickstart - How specify location of individual package in Workstation folder?

- by Ed

I keep getting "package does not exist" errors during the install. I made a kickstart ISO to create an unattended install of a RHEL 5.3 build machine for C++ software releases. It pulls the kickstart config file from our internal web server. This is handy; it makes it easy to test and modify without having to make a new ISO. And I plan to check it in to version control if I can get it working. Anyway, the rpm packages are located in two folders on the disk; Client and Workstation. The packages install fine for the ones that are physically located under the Client folder. It cannot find those under the Workstation folder such as as doxygen and subversion complaining that packages do not exist. Is there a way to specify the individual package location? # ----------------------------------------------------------------------------- # P A C K A G E S # ----------------------------------------------------------------------------- %packages @gnome-desktop @core @base @base-x @printing @development-tools emacs kexec-tools fipscheck xorg-x11-server-Xnest xorg-x11-server-Xvfb #Packages Located in Workstation Folder *** Install can not find any of these ?? bison doxygen gcc-c++ subversion zlib-devel freetype-devel libxml2-devel Thanks in advance, -Ed

Read the article

On clients use generic driver for printer shared by CUPS

- by Daniel

I know this worked really easy with a recent CUPS version some years ago. Unfortunately I fail to do the following with latest CUPS nowadays. How to share a printer without using printer specific drivers on the clients with CUPS? The printer is a Samsung ML-2010. The important fact is that it needs a quite specific library for printing called splix. That is installed on the server and prints well. What makes trouble is using that printer over the network. I found out how to use Avahi under Linux to make use of DNSSD to advertise and discover printers. But as far as I understand the new CUPS offers the internal driver interface on the network. This has 2 major issues: anybody can fiddle with the driver and I don't trust any uncommon printer library to be "network secure" anyone who wants to use my printer including guests needs to install the specific drivers first I remember the old days when I could enable "Share this printer" on the CUPS server and all clients would magically detect the printer and just send their job data to the server and have it do the driver stuff. After everything a read I guess this is related to the changes Apple introduced with CUPS including dropping of the integrated network discovery protocol. If it helps: Server: Ubuntu LTS 12.04 Server with CUPS 1.5.3 Client: Arch Linux with current CUPS 1.6.1 On another box with Ubuntu the printer was setup automatically at least but the mechanism used the Splix library for that.

Read the article

How to turn off Windows Azure's "This copy of Windows is not genuine" message?

- by Sid

Is there any setting/configuration item to avoid Windows Azure from printing that error on the screen or detecting it? I've put a screenshot below that shows the message when you RDP into the web role. My web role runs on Windows Azure Guest OS 1.17 (variant of Windows Server 2008 SP2) Background: I was explaining our architecture to some outside engineers (NDA'd and all) and had to demystify the webrole as they were unfamiliar with Azure. I RDP'd into the VMs running the Web Role when one of their engineers gasped "are you guys running pirated copies of Windows in the cloud?" I also noticed that within the RDP screen, the Azure machines had "This copy of Windows is not genuine" on the bottom left corner. Now obviously, Microsoft is running their own OS in their own datacenter with no influence from me. So no 'piracy' here, despite that obvious warning. However, they seemed so distracted by this ("how can it be? really? hmmm?") that we wasted more time talking about it than the actual matter at work. Like I said, they have little exposure to Azure but have value add elsewhere. I want to get rid of this so I don't have to explain this in the future. PS Microsoft: If you're going to modify Windows Server <XYZ> into Windows Azure <A.B> , you should also modify the code that verifies product integrity.

Read the article

"Document in ADF" on Canon MX340

- by Michael Donohue

I have a Canon MX340 multifunction printer. Recently, it keeps saying "Document in ADF" when I turn on the printer. I've tried clearing this multiple times, but as soon as the feeder wheels stop turning, in an attempt to clear the document feeder, it just pops up the same error again. This is particularly annoying, as it blocks all functions on the device - I cannot print, even though printing has no interaction with the document feeder. I've opened up the feeder device, as much as can be done with fingers alone. There just doesn't seem to be anything in there. I ran a sheet of paper through about six times, just to see if some dust might be getting in the way, and I've blown out the feeder with air. Still nothing. At this point, I don't care too much about the ADF working, I just want to disable whatever sensor is tripping this error message. Any ideas? I found this thread online, where a user has the same problem. But no resolution was reached there.

Read the article

amazon ec2-medium apache requests per second terrible

- by TheDayIsDone

EDITED -- test running from localhost now to rule out network... i have a c1.medium using EBS. when i do an apache benchmark and i'm just printing a "hello" for the test from localhost - no database hits, it's very slow. i can repeat this test many times with the same results. any thoughts? thanks in advance. ab -n 1000 -c 100 http://localhost/home/test/ Benchmarking localhost (be patient) Completed 100 requests Completed 200 requests Completed 300 requests Completed 400 requests Completed 500 requests Completed 600 requests Completed 700 requests Completed 800 requests Completed 900 requests Completed 1000 requests Finished 1000 requests Server Software: Apache/2.2.23 Server Hostname: localhost Server Port: 80 Document Path: /home/test/ Document Length: 5 bytes Concurrency Level: 100 Time taken for tests: 25.300 seconds Complete requests: 1000 Failed requests: 0 Write errors: 0 Total transferred: 816000 bytes HTML transferred: 5000 bytes Requests per second: 39.53 [#/sec] (mean) Time per request: 2530.037 [ms] (mean) Time per request: 25.300 [ms] (mean, across all concurrent requests) Transfer rate: 31.50 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 0 7 21.0 0 73 Processing: 81 2489 665.7 2500 4057 Waiting: 80 2443 654.0 2445 4057 Total: 85 2496 653.5 2500 4057 Percentage of the requests served within a certain time (ms) 50% 2500 66% 2651 75% 2842 80% 2932 90% 3301 95% 3506 98% 3762 99% 3838 100% 4057 (longest request)

Read the article

Printer spools but doesn't print

- by DKNUCKLES

I am having a bizarre issue with an end user who is unable to print to a USB attached printer. The environment is as Windows 7 machine with a Canon Pixma iP90 printer. The driver is installed (and has been re-installed several times), but whenever a print job is sent the printer spools but no printing ever occurs. The following is some relevant information I can confirm that the printer is spooling as the spool folder fills up, and the job "releases" and the spool folder empties I have turned off print spooling with no luck None of the features from the Canon utilities (ie Turn Printer Off) features work Computer recognizes the printer as being installed. When the cable is unplugged the printer icon grey's out in Devices and Printers Printer and cable are confirmed working as they work with other PC's in the office I have deleted the USB Root Hub devices and rebooted the machine with no luck No error messages are displayed or logged in the event viewer. The Canon diagnostics utility doesn't detect any problem and states the printer is functioning properly Printer is not shared User is able to print to other shared printers in the office Any help with this issue would be greatly appreciated.

Read the article

HP LaserJet 1515: Disable "refill" warning

- by Pekka

I have a HP LaserJet 1515 connected to a Windows 7 PC. The Magenta cartridge is empty; the printer shows a warning to that effect, and won't let me print even black-and-white documents any more. I can't turn the warning off manually using the printer's small console: When I try to enter any menu, the display says "Menu access disabled". I have no idea why. There is a setting to override the warning, but it can't be changed using the Network interface in the browser (Although it is there on the status page) According to the manual,the HP printing tool is supposed to offer a switch for this, but it won't install on my Windows 7. It just rumbles about for half an hour, to magnificently exit with an "unknown error" requiring a reboot. On second look, the problem seems to be that Windows 7 just isn't supported. There is no download link for the tool when you specify Windows 7 as your OS. I just want to print a black-and-white-document on a printer whose black cartridge is still 65% full. Is this indeed impossible? On second thought, I'm cross-posting this on the HP support forum. I'll update here if anything comes up.

Read the article

WINDOWS 7: Make the contents of two folders appear in one

- by big_smile

In Windows 7, I have three folders: "Images", "assets" and "all". I want the contents of "Images " and "assets" to appear in "all" automatically without copying those files into that folder (e.g. I don't want to duplicate the files). I also only want the contents to be copied over and not the folders themslves (The reason for this is that if the folders are copied over, they will become sub-directories. I am using a printing hot folder that access "all" but it can't see any subdirectories in "all"). When Images and Assets are updated (e.g. with files being added or deleted), "all" should automatically update as well. How can I do this? This is what I have tried: Libraries: This is a feature built into Windows. It works exactly as I want. However, the print hot folder cannot recognise the library as a folder. Sym Link Extension: I can use this to make the "images" and "assets" folders appear as a sub directories of "all". However, I want the contents of "images"/"assets" to appear in the "all" folder (I don't want the directories to appear as sub directories, because as stated, the print hot folder cannot access sub directories).

Read the article

I have a problem with a AE1200 Cisco/Linksys Wireless-N USB adapter having stopped working after I ran the update manager in Ubuntu 12.04

- by user69670

Here is the problem, I use a Cisco/Linksys AE1200 wireless network adapter to connect my desktop to a public wifi internet connection. I use ndiswrapper to use the windows driver and it had been working fine for me untill I ran the update manager overnight a few days ago. When I woke up it was asking for the normal computer restart to implement the changes but after rebooting the computer, the wireless adapter did not work, the status light on the adapter did not light up even though ubuntu recognizes it is there and according to ndiswrapper the drivers are loaded and the hardware is present. the grep command is being a bitch for some unknown reason today so this will be long sorry Output from "lspci": 00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI Radeon Xpress 200 Host Bridge (rev 01) 00:01.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:12.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI0) 00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI1) 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI2) 00:13.3 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI3) 00:13.4 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI4) 00:13.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB Controller (EHCI) 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 13) 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB600 IDE 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB600 PCI to LPC Bridge 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RC410 [Radeon Xpress 200] 02:02.0 Communication controller: Conexant Systems, Inc. HSF 56k Data/Fax Modem 02:03.0 Multimedia audio controller: Creative Labs CA0106 Soundblaster 02:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Output from "lsusb": Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 009: ID 13b1:0039 Linksys AE1200 802.11bgn Wireless Adapter [Broadcom BCM43235] Bus 003 Device 002: ID 045e:0053 Microsoft Corp. Optical Mouse Bus 004 Device 002: ID 1043:8006 iCreate Technologies Corp. Flash Disk 32-256 MB Output from "ifconfig": eth0 Link encap:Ethernet HWaddr 00:19:21:b6:af:7c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:20 Base address:0xb400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:13232 errors:0 dropped:0 overruns:0 frame:0 TX packets:13232 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1084624 (1.0 MB) TX bytes:1084624 (1.0 MB) Output from "iwconfig": lo no wireless extensions. eth0 no wireless extensions. Output from "lsmod": Module Size Used by nls_iso8859_1 12617 1 nls_cp437 12751 1 vfat 17308 1 fat 55605 1 vfat uas 17828 0 usb_storage 39646 1 nls_utf8 12493 1 udf 84366 1 crc_itu_t 12627 1 udf snd_ca0106 39279 2 snd_ac97_codec 106082 1 snd_ca0106 ac97_bus 12642 1 snd_ac97_codec snd_pcm 80845 2 snd_ca0106,snd_ac97_codec rfcomm 38139 0 snd_seq_midi 13132 0 snd_rawmidi 25424 2 snd_ca0106,snd_seq_midi bnep 17830 2 parport_pc 32114 0 bluetooth 158438 10 rfcomm,bnep ppdev 12849 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq snd 62064 11 snd_ca0106, snd_ac97_codec,snd_pcm,snd_rawj9fe snd_ca0106,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_ca0106,snd_pcm sp5100_tco 13495 0 i2c_piix4 13093 0 radeon 733693 3 ttm 65344 1 radeon drm_kms_helper 45466 1 radeon drm 197692 5 radeon,ttm,drm_kms_helper i2c_algo_bit 13199 1 radeon mac_hid 13077 0 shpchp 32325 0 ati_agp 13242 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp usbhid 41906 0 hid 77367 1 usbhid 8139too 23283 0 8139cp 26759 0 pata_atiixp 12999 1 Output from "sudo lshw -C network": *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 5 bus info: pci@0000:02:05.0 logical name: eth0 version: 10 serial: 00:19:21:b6:af:7c size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 10 0bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=64 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:20 ioport:b400(size=256) memory:ff5fdc00-ff5fdcff Output from "iwlist scan": lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. Output from "lsb_release -d": Ubuntu 12.04 LTS Output from "uname -mr": 3.2.0-24-generic-pae i686 Output from "sudo /etc/init.d/networking restart": * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... [ OK ]

Read the article

Can't connect to Wired Network after installing 12.04

- by ezz9

I have installed 12.04 into a used HP Compaq DC 7100 CMT. Plugged in LAN cable into the computer and it says network disconnected. from what I understand on the things I've read, it's not getting the address right, maybe it's just a guess (hardware address 00:16:35:78:47:bb). I know the LAN cable is working I can get on the net with the old computer. (Old computer is using device MAC address; Auto eth0 00:11:11:E6:4F:FE). I have put this address into the newer HP and it shows last used (minutes ago) but no Internet sever not found. I tried the hardware address it says never. I feel and think this should be easy to fix. But I just don't know. Here is the info everyone has asked for, but they never say what I should do. sudo lshw -C network; rfkill list; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; uname -a; ifconfig; route -n *-network description: ethernet interface product; NetXtreme BCM5751 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:40:00.0 logical name: eth0 verson: 01 serial: 00:16:35:78:47:bb size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000-fd configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion= 3.121 duplex=full firmware=5751-v3.29a latency=0 link=yes multicast=yes port=twi sted pair speed=100Mbit/s resources: irq:17 memory:f0400000-f040ffff auto lo iface lo inet loopback DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION= "Ubuntu 12.04 LTS" 00:00.0 host bridge [0600]: Inter Corporation 82915G/P/GV/GL/PL/910GL Memory Con troller Hub [8086:2580] (rev 04) 00.02.0 VGA compatible controller [0300]: Intel Corporation 82915G/GV/910GL inte grated Graphics Controller [8086:2582] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 [8086:2660] (rev 03) 00:1c.1 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 [8086:2662] (rev 03) 00:1d.0 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #1 [8086:2658] (rev 03) 00:1d.1 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #2 [8086:2659] (rev 03) 00:1d.2 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #3 [8086:265a] (rev 03) 00:1d.3 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #4 [8086:265b] (rev 03) 00:1d.7 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB2 UHCI Controller [8086:265c] (rev 03) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI bridge [8086:244e] (rev d 3) 00:1e.2 Multimedia audio controller [0401]: Intel Corporation 82801FB/FBM/FR/FW/ FRW (ICH6 Family) AC'97 Autio conrtroller [8086:266e] (rev 03) 00:1f.0 ISA bridge [0601]: Intel Corporation 82801FB/RF (ICH6/ICH6R) LPC Interfa ce Bridge [8086:2640] (rev 03) 00:1f.1 IDE interface [0101]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 fami ly) IDE Controller [8086:266f] (rev 03) 00:1f.2 IDE interface [0101]: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Con troller [8086:2651] (rev 03) 40:00.0 Ethernet controller [0200]: Broadcom Corporation NetXreme BCM5751 Gigab it Ethernet PCI Express [14e4:1677} (rev 01) Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Linux bob-desktop 3.2.0-23-generic-pae #36-Ubuntu SMP Tpr 10 22:19:09 UTC 20 12 i686 i686 i386 GNU/Linux eth0 Link encap:Ethernet HWaddr 00:16:35:78:47:bb inet6 addr: fe80::216:35ff:47bb/64 Scope:link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2517 errors:0 dropped:0 overruns:0 frame:0 TX packets:164 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:164508 (164.5 KB) TX bytes: 40884 (40.0 KB) Interrupt:17 lo Link encap:Local loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3290 errors:0 dropped:0 overruns:0 frame:0 TX packets:3290 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen: 0 RX bytes:267212 (267.2 KB) TX bytes: 267212 (267.2 KB) Kernel Ip routing table Destination Gateway Genmask Flags Metric Ref Use Iface ran this sudo dhclient eth0 no reply ran this ip addr 1: lo <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST ,MULTICAST ,UP ,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000 link/enter 00:16:35:78:47:BB brd ff:ff:ff:ff:ff:ff inet 169.254.7.172/16 brd 169.254.255.255 scope link eth0:avahi inet6 fe80::216:35ff:fe78:47bb/64 scope link valid_lft forever preferred_lft forever Help please.

Read the article

Cannot connect to secure wireless with Netgear wna3100 USB

- by Vince Radice

I have installed Ubuntu 11.10. I used a wired connection to download and install all of the updates. When I tried to use a Netgear WNA3100 wireless USB network adapter, it failed. Much searching and trying things I was finally able to get it working by disabling security on my router. I have verified this by disabling security and I was able to connect. When I enabled security (WPA2 PSK), the connection failed. What is necessary to enable security (WPA2 PSK) and still use the Netgear USB interface? Here is the output from the commands most requested lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0846:9020 NetGear, Inc. WNA3100(v1) Wireless-N 300 [Broadcom BCM43231] lshw -C network *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:40:ca:44:e6:3e size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=32 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:c800(size=256) memory:ee011000-ee0110ff memory:40000000-4000ffff *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: e0:91:f5:56:e1:0d capabilities: ethernet physical wireless configuration: broadcast=yes driver=ndiswrapper+bcmn43xx32 driverversion=1.56+,08/26/2009, 5.10.79.30 ip=192.168.1.104 link=yes multicast=yes wireless=IEEE 802.11g iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11g ESSID:"vincecarolradice" Mode:Managed Frequency:2.422 GHz Access Point: A0:21:B7:9F:E5:EE Bit Rate=121.5 Mb/s Tx-Power:32 dBm RTS thr:2347 B Fragment thr:2346 B Encryption key:off Power Management:off Link Quality:76/100 Signal level:-47 dBm Noise level:-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ndiswrapper -l bcmn43xx32 : driver installed device (0846:9020) present lsmod | grep ndis ndiswrapper 193669 0 dmesg | grep -e ndis -e wlan [ 907.466392] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 907.838507] ndiswrapper (import:233): unknown symbol: ntoskrnl.exe:'IoUnregisterPlugPlayNotification' [ 907.838955] ndiswrapper: driver bcmwlhigh5 (Netgear,11/05/2009, 5.60.180.11) loaded [ 908.137940] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmwlhigh5, version: 0x53cb40b, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 908.141879] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 908.143048] usbcore: registered new interface driver ndiswrapper [ 908.178826] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 994.015088] usbcore: deregistering interface driver ndiswrapper [ 994.028892] ndiswrapper: device wlan0 removed [ 994.080558] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 994.374929] ndiswrapper: driver bcmn43xx32 (,08/26/2009, 5.10.79.30) loaded [ 994.404366] ndiswrapper (mp_init:219): couldn't initialize device: C0000001 [ 994.404384] ndiswrapper (pnp_start_device:435): Windows driver couldn't initialize the device (C0000001) [ 994.404666] ndiswrapper (mp_halt:262): device e05b6480 is not initialized - not halting [ 994.404671] ndiswrapper: device eth%d removed [ 994.404709] ndiswrapper: probe of 1-5:1.0 failed with error -22 [ 994.406318] usbcore: registered new interface driver ndiswrapper [ 2302.058692] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmn43xx32, version: 0x50a4f1e, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 2302.060882] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 2302.113838] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2354.611318] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2355.268902] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2365.400023] wlan0: no IPv6 routers present [ 2779.226096] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2779.422343] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2797.574474] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2802.607937] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2803.261315] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2813.952028] wlan0: no IPv6 routers present [ 3135.738431] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3139.180963] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3139.816561] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.229872] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.444542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.758297] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.860684] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.118732] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.139553] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.300542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3353.341402] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3363.266399] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.505475] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.506619] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3363.717203] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.779206] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.206152] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.248624] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.577664] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3438.852457] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3438.908573] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.282995] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.325237] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.460716] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.461763] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.809776] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.880641] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.122848] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.148328] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.324502] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3636.088798] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3636.712186] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 3647.600040] wlan0: no IPv6 routers present I am using the system now with the router security turned off. When I submit this, I will turn security back on.

Read the article

Wireless not working on Dell XPS 17 after installing 12.04

- by user60622

I (linux newbie) have a Dell XPS 17 and tried to install Ubuntu 12.04. After installation all WLAN accesspoints near are detected. But I can not connect (but I am able to connect with other computers as well as with Dell XPS 17 under windows). Outputs: iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:"LerchenPoint" Mode:Managed Frequency:2.412 GHz Access Point: 58:6D:8F:A0:2D:58 Bit Rate=1 Mb/s Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-37 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:19 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:99:98:28 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-24-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:50 memory:f0400000-f0401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:0a:00.0 logical name: eth0 version: 06 serial: f0:4d:a2:56:e3:94 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.123 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:47 ioport:6000(size=256) memory:f0a04000-f0a04fff memory:f0a00000-f0a03fff dmesg | grep iwl [ 10.157531] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 10.157561] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 10.157598] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 10.157599] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 10.157601] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 10.157731] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 10.157834] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 10.157976] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 10.179772] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 10.179775] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 10.179777] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 10.179796] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 10.574728] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 10.726409] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 19.714132] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 19.777862] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2251.603089] iwlwifi 0000:04:00.0: PCI INT A disabled [ 2266.578350] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 2266.578399] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 2266.578435] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 2266.578437] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 2266.578439] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 2266.578704] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 2266.578808] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 2266.578916] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.600709] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 2266.600712] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 2266.600713] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 2266.600727] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 2266.605978] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 2266.606331] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 2266.614179] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.681541] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S Solutions I tried: rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. rmmod /lib/modules/3.2.0-24-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/wireless/cfg80211.ko sudo modprobe iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. replacing iwlwifi-1000-5.ucode (current driver) against iwlwifi-1000-3.ucode sudo jockey-gtk: (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed nothing is listet in "Additional drivers" (german: "Zusätzliche Treiber"). gksudo gedit /etc/modprobe.d/blacklist.conf add "blacklist acer_wmi" Any help would be appreciated very much. Thanks!!

Read the article

External USB 3 drive not recognized

- by ilan123

Ubuntu 12.10 64 bit seems not to recognize my external hard disk. It is a Vantec NST-310S3 external disk enclosure with a WD 3TB drive. The disk has two NTFS partitions. My PC is a dual boot system. Under Windows 7 the hard disk works fine but I can't make it work with Ubuntu. When the drive is connected to the PC then the command sudo fdisk -l seems to hang forever. Below are the output of lsusb and cat /proc/partitions without the external drive and then with it connected. I added also the last lines of the dmesg command at the end. First without the drive: ilan@linux:~$ lsusb Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 13ba:0017 Unknown PS/2 Keyboard+Mouse Adapter Bus 001 Device 004: ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver Bus 001 Device 005: ID 0ac8:3420 Z-Star Microelectronics Corp. Venus USB2.0 Camera ilan@linux:~$ cat /proc/partitions major minor #blocks name 8 0 1953514584 sda 8 1 102400 sda1 8 2 629043200 sda2 8 3 367001600 sda3 8 4 1 sda4 8 5 471859200 sda5 8 6 157286400 sda6 8 7 324115456 sda7 8 8 4101120 sda8 11 0 1048575 sr0 Second with the USB 3 drive: ilan@linux:~$ lsusb Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 004 Device 002: ID 174c:55aa ASMedia Technology Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 13ba:0017 Unknown PS/2 Keyboard+Mouse Adapter Bus 001 Device 004: ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver Bus 001 Device 005: ID 0ac8:3420 Z-Star Microelectronics Corp. Venus USB2.0 Camera ilan@linux:~$ cat /proc/partitions major minor #blocks name 8 0 1953514584 sda 8 1 102400 sda1 8 2 629043200 sda2 8 3 367001600 sda3 8 4 1 sda4 8 5 471859200 sda5 8 6 157286400 sda6 8 7 324115456 sda7 8 8 4101120 sda8 11 0 1048575 sr0 8 16 2930266584 sdb ilan@linux:~$ lsusb -v -s 004:002 Bus 004 Device 002: ID 174c:55aa ASMedia Technology Inc. Couldn't open device, some information will be missing Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 9 idVendor 0x174c ASMedia Technology Inc. idProduct 0x55aa bcdDevice 1.00 iManufacturer 2 iProduct 3 iSerial 1 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 44 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk-Only iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0400 1x 1024 bytes bInterval 0 bMaxBurst 15 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0400 1x 1024 bytes bInterval 0 bMaxBurst 15 ilan@linux:~$ sudo fdisk -l [sudo] password for ilan: Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf1b4f1ee Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 1258293247 629043200 7 HPFS/NTFS/exFAT /dev/sda3 1258293248 1992296447 367001600 7 HPFS/NTFS/exFAT /dev/sda4 1992298494 3907028991 957365249 f W95 Ext'd (LBA) /dev/sda5 1992298496 2936016895 471859200 7 HPFS/NTFS/exFAT /dev/sda6 2936018944 3250591743 157286400 7 HPFS/NTFS/exFAT /dev/sda7 3250593792 3898824703 324115456 83 Linux /dev/sda8 3898826752 3907028991 4101120 82 Linux swap / Solaris dmesg output after connecting the external drive: [ 23.740567] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 23.740786] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 49.144673] usb 4-1: >new SuperSpeed USB device number 2 using xhci_hcd [ 49.163039] usb 4-1: >Parent hub missing LPM exit latency info. Power management will be impacted. [ 49.166789] usb 4-1: >New USB device found, idVendor=174c, idProduct=55aa [ 49.166793] usb 4-1: >New USB device strings: Mfr=2, Product=3, SerialNumber=1 [ 49.166796] usb 4-1: >Product: AS2105 [ 49.166799] usb 4-1: >Manufacturer: ASMedia [ 49.166801] usb 4-1: >SerialNumber: 0123456789ABCDEF [ 49.206372] usbcore: registered new interface driver uas [ 49.228891] Initializing USB Mass Storage driver... [ 49.229042] scsi6 : usb-storage 4-1:1.0 [ 49.229115] usbcore: registered new interface driver usb-storage [ 49.229116] USB Mass Storage support registered. [ 64.045528] scsi 6:0:0:0: >Direct-Access WDC WD30 EZRX-00MMMB0 80.0 PQ: 0 ANSI: 0 [ 64.046224] sd 6:0:0:0: >Attached scsi generic sg2 type 0 [ 64.046881] sd 6:0:0:0: >[sdb] Very big device. Trying to use READ CAPACITY(16). [ 64.047610] sd 6:0:0:0: >[sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) [ 64.048368] sd 6:0:0:0: >[sdb] Write Protect is off [ 64.048373] sd 6:0:0:0: >[sdb] Mode Sense: 23 00 00 00 [ 64.048984] sd 6:0:0:0: >[sdb] No Caching mode page present [ 64.048987] sd 6:0:0:0: >[sdb] Assuming drive cache: write through [ 64.049297] sd 6:0:0:0: >[sdb] Very big device. Trying to use READ CAPACITY(16). [ 64.050942] sd 6:0:0:0: >[sdb] No Caching mode page present [ 64.050944] sd 6:0:0:0: >[sdb] Assuming drive cache: write through [ 94.245006] usb 4-1: >reset SuperSpeed USB device number 2 using xhci_hcd [ 94.262553] usb 4-1: >Parent hub missing LPM exit latency info. Power management will be impacted. [ 94.263805] xhci_hcd 0000:03:00.0: >xHCI xhci_drop_endpoint called with disabled ep ffff8800d37d1c00 [ 94.263808] xhci_hcd 0000:03:00.0: >xHCI xhci_drop_endpoint called with disabled ep ffff8800d37d1c40 [ 125.262722] usb 4-1: >reset SuperSpeed USB device number 2 using xhci_hcd [ 125.280304] usb 4-1: >Parent hub missing LPM exit latency info. Power management will be impacted. [ 125.281511] xhci_hcd 0000:03:00.0: >xHCI xhci_drop_endpoint called with disabled ep ffff8800d37d1c00 [ 125.281516] xhci_hcd 0000:03:00.0: >xHCI xhci_drop_endpoint called with disabled ep ffff8800d37d1c40

Read the article

Computer Networks UNISA - Chap 8 – Wireless Networking

- by MarkPearl

After reading this section you should be able to Explain how nodes exchange wireless signals Identify potential obstacles to successful transmission and their repercussions, such as interference and reflection Understand WLAN architecture Specify the characteristics of popular WLAN transmission methods including 802.11 a/b/g/n Install and configure wireless access points and their clients Describe wireless MAN and WAN technologies, including 802.16 and satellite communications The Wireless Spectrum All wireless signals are carried through the air by electromagnetic waves. The wireless spectrum is a continuum of the electromagnetic waves used for data and voice communication. The wireless spectrum falls between 9KHZ and 300 GHZ. Characteristics of Wireless Transmission Antennas Each type of wireless service requires an antenna specifically designed for that service. The service’s specification determine the antenna’s power output, frequency, and radiation pattern. A directional antenna issues wireless signals along a single direction. An omnidirectional antenna issues and receives wireless signals with equal strength and clarity in all directions The geographical area that an antenna or wireless system can reach is known as its range Signal Propagation LOS (line of sight) uses the least amount of energy and results in the reception of the clearest possible signal. When there is an obstacle in the way, the signal may… pass through the object or be obsrobed by the object or may be subject to reflection, diffraction or scattering. Reflection – waves encounter an object and bounces off it. Diffraction – signal splits into secondary waves when it encounters an obstruction Scattering – is the diffusion or the reflection in multiple different directions of a signal Signal Degradation Fading occurs as a signal hits various objects. Because of fading, the strength of the signal that reaches the receiver is lower than the transmitted signal strength. The further a signal moves from its source, the weaker it gets (this is called attenuation) Signals are also affected by noise – the electromagnetic interference) Interference can distort and weaken a wireless signal in the same way that noise distorts and weakens a wired signal. Frequency Ranges Older wireless devices used the 2.4 GHZ band to send and receive signals. This had 11 communication channels that are unlicensed. Newer wireless devices can also use the 5 GHZ band which has 24 unlicensed bands Narrowband, Broadband, and Spread Spectrum Signals Narrowband – a transmitter concentrates the signal energy at a single frequency or in a very small range of frequencies Broadband – uses a relatively wide band of the wireless spectrum and offers higher throughputs than narrowband technologies The use of multiple frequencies to transmit a signal is known as spread-spectrum technology. In other words a signal never stays continuously within one frequency range during its transmission. One specific implementation of spread spectrum is FHSS (frequency hoping spread spectrum). Another type is known as DSS (direct sequence spread spectrum) Fixed vs. Mobile Each type of wireless communication falls into one of two categories Fixed – the location of the transmitted and receiver do not move (results in energy saved because weaker signal strength is possible with directional antennas) Mobile – the location can change WLAN (Wireless LAN) Architecture There are two main types of arrangements Adhoc – data is sent directly between devices – good for small local devices Infrastructure mode – a wireless access point is placed centrally, that all devices connect with 802.11 WLANs The most popular wireless standards used on contemporary LANs are those developed by IEEE’s 802.11 committee. Over the years several distinct standards related to wireless networking have been released. Four of the best known standards are also referred to as Wi-Fi. They are…. 802.11b 802.11a 802.11g 802.11n These four standards share many characteristics. i.e. All 4 use half duplex signalling Follow the same access method Access Method 802.11 standards specify the use of CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) to access a shared medium. Using CSMA/CA before a station begins to send data on an 802.11 network, it checks for existing wireless transmissions. If the source node detects no transmission activity on the network, it waits a brief period of time and then sends its transmission. If the source does detect activity, it waits a brief period of time before checking again. The destination node receives the transmission and, after verifying its accuracy, issues an acknowledgement (ACT) packet to the source. If the source receives the ACK it assumes the transmission was successful, – if it does not receive an ACK it assumes the transmission failed and sends it again. Association Two types of scanning… Active – station transmits a special frame, known as a prove, on all available channels within its frequency range. When an access point finds the probe frame, it issues a probe response. Passive – wireless station listens on all channels within its frequency range for a special signal, known as a beacon frame, issued from an access point – the beacon frame contains information necessary to connect to the point. Re-association occurs when a mobile user moves out of one access point’s range and into the range of another. Frames Read page 378 – 381 about frames and specific 802.11 protocols Bluetooth Networks Sony Ericson originally invented the Bluetooth technology in the early 1990s. In 1998 other manufacturers joined Ericsson in the Special Interest Group (SIG) whose aim was to refine and standardize the technology. Bluetooth was designed to be used on small networks composed of personal communications devices. It has become popular wireless technology for communicating among cellular telephones, phone headsets, etc. Wireless WANs and Internet Access Refer to pages 396 – 402 of the textbook for details.

Read the article

Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to get it to work?

- by zewone

I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686 ![Schizophrenic Ubuntu](http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) Any help much appreciated... Thanks, Philippe 31-10-2012 ... I have some more updates. When I do the following command it does see my Wifi router... So even if it is still disabled... the card seems to work and see the router (ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E") See below: sudo iwlist wlan1 scanning wlan1 Scan completed : Cell 01 - Address: 00:19:70:8F:B0:EA Channel:10 Frequency:2.457 GHz (Channel 10) Quality=51/70 Signal level=-59 dBm Encryption key:on ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000025dbf2188 Extra: Last beacon: 108ms ago IE: Unknown: 002035373931424332362D434539432D313144312D393742462D3030303046383145 IE: Unknown: 010882848B960C121824 IE: Unknown: 03010A IE: Unknown: 0706424520010D14 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101030003A4000027A4000042435E0062322F00 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000

Read the article

Intel Centrino Wireless-N 1000 Again ! Ubuntu 13.04 x64

- by vafa

First I have to say that I tried everything written about this concept. The problem is that it stops working randomly in 3 main forms : 1 - sometimes it disconnect from wireless network and reconnect automatically 2 - sometimes it disconnect and wont connect no matter what (needs reboot) 3 - some times it's still connected but cannot ping or surf or whatever. I already tried disabling N mod using these commands : sudo modprobe -r iwlwifi modprobe iwlwifi 11n_disable=1 (or 0, whatever) it didn't help . these are the results of lspci, sudo lshw -C network, ifconfig, iwconfig, rfkill list when it disconnected and didn't connect till reboot : ifconfig : eth0 Link encap:Ethernet HWaddr c8:0a:a9:34:65:77 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1563213476557380 errors:9379306629148050 dropped:3126435543049350 overruns:1563217771524675 frame:7816088857623375 TX packets:1563217771524675 errors:6252871086098700 dropped:0 overruns:1563217771524675 carrier:3126435543049350 collisions:7816088857623375 txqueuelen:1000 RX bytes:1563217771524675 (1.5 PB) TX bytes:1563217771524675 (1.5 PB) ham0 Link encap:Ethernet HWaddr 7a:79:19:a5:e4:93 inet addr:25.165.228.147 Bcast:25.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:19ff:fea5:e493/64 Scope:Link inet6 addr: 2620:9b::19a5:e493/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:7743 errors:0 dropped:0 overruns:0 frame:0 TX packets:1250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:665642 (665.6 KB) TX bytes:204056 (204.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:41138 errors:0 dropped:0 overruns:0 frame:0 TX packets:41138 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6420962 (6.4 MB) TX bytes:6420962 (6.4 MB) wlan0 Link encap:Ethernet HWaddr 00:1e:64:45:fb:70 inet6 addr: fe80::21e:64ff:fe45:fb70/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:286999 errors:0 dropped:0 overruns:0 frame:0 TX packets:226966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:324386887 (324.3 MB) TX bytes:30674804 (30.6 MB) iwconfig : ham0 no wireless extensions. eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off sudo lshw -C network: *-network description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:45:fb:70 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-30-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:46 memory:c0400000-c0401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: c0 serial: c8:0a:a9:34:65:77 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:c0900000-c093ffff ioport:5000(size=128) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:19:a5:e4:93 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full ip=25.165.228.147 link=yes multicast=yes port=twisted pair speed=10Mbit/s lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: NVIDIA Corporation G98M [GeForce G 105M] (rev a1) 07:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak] 09:00.0 Ethernet controller: Qualcomm Atheros AR8131 Gigabit Ethernet (rev c0) rfkill list : 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 9: phy0: Wireless LAN Soft blocked: no Hard blocked: no any help will be REALLLYYYY appreciated

Read the article

Multiple Audio Issues

- by Lerp

I am having issues with my audio on Ubuntu 12.04, I will try and give as much detail as possible so sorry if there's too much detail. The Problem Audio plays from both speakers and headphone regardless of what connector I choose and regardless of the profile I use. The microphone is constantly being played through headphones & speakers. The headphone audio is extremely quiet but plays from both ears when I select "Headphones" for the connector in Sound Settings. The headphone audio only plays from one ear and is quiet (but not as quiet as above) when I select "Analogue Output" for the connector in Sound Settings. I can only select "Headphones" as the connector in Sound Settings if I set the profile to either "Analogue Stereo Output/Duplex", all others only allow me to choose "Analogue Output" for the connector. Despite the headphone sound issues, the speaker sound is fine apart from the fact that I am not able to select which output is used, they just both play. My headphone and microphone are plugged into the front and my speakers are plugged into the back. What I have tried I have put everything in alsamixer to 100 apart from "Front Mic Boost" which I have set to 0. Command Output aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: AD198x Analog [AD198x Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: AD198x Digital [AD198x Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 2: AD198x Headphone [AD198x Headphone] Subdevices: 1/1 Subdevice #0: subdevice #0 arecord -l **** List of CAPTURE Hardware Devices **** card 0: Intel [HDA Intel], device 0: AD198x Analog [AD198x Analog] Subdevices: 2/3 Subdevice #0: subdevice #0 Subdevice #1: subdevice #1 Subdevice #2: subdevice #2 cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xf7ff8000 irq 70 cat /proc/asound/modules 0 snd_hda_intel cat /proc/asound/card*/codec* | grep "Codec" Codec: Analog Devices AD1989B cat /etc/modprobe.d/alsa-base.conf # autoloader aliases install sound-slot-0 /sbin/modprobe snd-card-0 install sound-slot-1 /sbin/modprobe snd-card-1 install sound-slot-2 /sbin/modprobe snd-card-2 install sound-slot-3 /sbin/modprobe snd-card-3 install sound-slot-4 /sbin/modprobe snd-card-4 install sound-slot-5 /sbin/modprobe snd-card-5 install sound-slot-6 /sbin/modprobe snd-card-6 install sound-slot-7 /sbin/modprobe snd-card-7 # Cause optional modules to be loaded above generic modules install snd /sbin/modprobe --ignore-install snd $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-ioctl32 ; /sbin/modprobe --quiet --use-blacklist snd-seq ; } # # Workaround at bug #499695 (reverted in Ubuntu see LP #319505) install snd-pcm /sbin/modprobe --ignore-install snd-pcm $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-pcm-oss ; : ; } install snd-mixer /sbin/modprobe --ignore-install snd-mixer $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-mixer-oss ; : ; } install snd-seq /sbin/modprobe --ignore-install snd-seq $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; /sbin/modprobe --quiet --use-blacklist snd-seq-oss ; : ; } # install snd-rawmidi /sbin/modprobe --ignore-install snd-rawmidi $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; : ; } # Cause optional modules to be loaded above sound card driver modules install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-emu10k1-synth ; } install snd-via82xx /sbin/modprobe --ignore-install snd-via82xx $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq ; } # Load saa7134-alsa instead of saa7134 (which gets dragged in by it anyway) install saa7134 /sbin/modprobe --ignore-install saa7134 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist saa7134-alsa ; : ; } # Prevent abnormal drivers from grabbing index 0 options bt87x index=-2 options cx88_alsa index=-2 options saa7134-alsa index=-2 options snd-atiixp-modem index=-2 options snd-intel8x0m index=-2 options snd-via82xx-modem index=-2 options snd-usb-audio index=-2 options snd-usb-caiaq index=-2 options snd-usb-ua101 index=-2 options snd-usb-us122l index=-2 options snd-usb-usx2y index=-2 # Ubuntu #62691, enable MPU for snd-cmipci options snd-cmipci mpu_port=0x330 fm_port=0x388 # Keep snd-pcsp from being loaded as first soundcard options snd-pcsp index=-2 # Keep snd-usb-audio from beeing loaded as first soundcard options snd-usb-audio index=-2 Hopefully I have provided enough information, I will happily provide anymore information needed. Thank you. Update Reinstalling alsa-base and pulseaudio fixed the headphone issues I was having.

Read the article

Processing Text and Binary (Blob, ArrayBuffer, ArrayBufferView) Payload in WebSocket - (TOTD #185)

- by arungupta

The WebSocket API defines different send(xxx) methods that can be used to send text and binary data. This Tip Of The Day (TOTD) will show how to send and receive text and binary data using WebSocket. TOTD #183 explains how to get started with a WebSocket endpoint using GlassFish 4. A simple endpoint from that blog looks like: @WebSocketEndpoint("/endpoint") public class MyEndpoint { public void receiveTextMessage(String message) { . . . } } A message with the first parameter of the type String is invoked when a text payload is received. The payload of the incoming WebSocket frame is mapped to this first parameter. An optional second parameter, Session, can be specified to map to the "other end" of this conversation. For example: public void receiveTextMessage(String message, Session session) { . . . } The return type is void and that means no response is returned to the client that invoked this endpoint. A response may be returned to the client in two different ways. First, set the return type to the expected type, such as: public String receiveTextMessage(String message) { String response = . . . . . . return response; } In this case a text payload is returned back to the invoking endpoint. The second way to send a response back is to use the mapped session to send response using one of the sendXXX methods in Session, when and if needed. public void receiveTextMessage(String message, Session session) { . . . RemoteEndpoint remote = session.getRemote(); remote.sendString(...); . . . remote.sendString(...); . . . remote.sendString(...); } This shows how duplex and asynchronous communication between the two endpoints can be achieved. This can be used to define different message exchange patterns between the client and server. The WebSocket client can send the message as: websocket.send(myTextField.value); where myTextField is a text field in the web page. Binary payload in the incoming WebSocket frame can be received if ByteBuffer is used as the first parameter of the method signature. The endpoint method signature in that case would look like: public void receiveBinaryMessage(ByteBuffer message) { . . . } From the client side, the binary data can be sent using Blob, ArrayBuffer, and ArrayBufferView. Blob is a just raw data and the actual interpretation is left to the application. ArrayBuffer and ArrayBufferView are defined in the TypedArray specification and are designed to send binary data using WebSocket. In short, ArrayBuffer is a fixed-length binary buffer with no format and no mechanism for accessing its contents. These buffers are manipulated using one of the views defined by one of the subclasses of ArrayBufferView listed below: Int8Array (signed 8-bit integer or char) Uint8Array (unsigned 8-bit integer or unsigned char) Int16Array (signed 16-bit integer or short) Uint16Array (unsigned 16-bit integer or unsigned short) Int32Array (signed 32-bit integer or int) Uint32Array (unsigned 16-bit integer or unsigned int) Float32Array (signed 32-bit float or float) Float64Array (signed 64-bit float or double) WebSocket can send binary data using ArrayBuffer with a view defined by a subclass of ArrayBufferView or a subclass of ArrayBufferView itself. The WebSocket client can send the message using Blob as: blob = new Blob([myField2.value]);websocket.send(blob); where myField2 is a text field in the web page. The WebSocket client can send the message using ArrayBuffer as: var buffer = new ArrayBuffer(10);var bytes = new Uint8Array(buffer);for (var i=0; i<bytes.length; i++) { bytes[i] = i;}websocket.send(buffer); A concrete implementation of receiving the binary message may look like: @WebSocketMessagepublic void echoBinary(ByteBuffer data, Session session) throws IOException { System.out.println("echoBinary: " + data); for (byte b : data.array()) { System.out.print(b); } session.getRemote().sendBytes(data);} This method is just printing the binary data for verification but you may actually be storing it in a database or converting to an image or something more meaningful. Be aware of TYRUS-51 if you are trying to send binary data from server to client using method return type. Here are some references for you: JSR 356: Java API for WebSocket - Specification (Early Draft) and Implementation (already integrated in GlassFish 4 promoted builds) TOTD #183 - Getting Started with WebSocket in GlassFish TOTD #184 - Logging WebSocket Frames using Chrome Developer Tools, Net-internals and Wireshark Subsequent blogs will discuss the following topics (not necessary in that order) ... Error handling Custom payloads using encoder/decoder Interface-driven WebSocket endpoint Java client API Client and Server configuration Security Subprotocols Extensions Other topics from the API

Read the article

How to send messages between c++ .dll and C# app using named pipe?

- by Gal

I'm making an injected .dll written in C++, and I want to communicate with a C# app using named pipes. Now, I am using the built in System.IO.Pipe .net classes in the C# app, and I'm using the regular functions in C++. I don't have much experience in C++ (Read: This is my first C++ code..), tho I'm experienced in C#. It seems that the connection with the server and the client is working, the only problem is the messaged aren't being send. I tried making the .dll the server, the C# app the server, making the pipe direction InOut (duplex) but none seems to work. When I tried to make the .dll the server, which sends messages to the C# app, the code I used was like this: DWORD ServerCreate() // function to create the server and wait till it successfully creates it to return. { hPipe = CreateNamedPipe(pipename,//The unique pipe name. This string must have the following form: \\.\pipe\pipename PIPE_ACCESS_DUPLEX, PIPE_TYPE_MESSAGE | PIPE_READMODE_MESSAGE | PIPE_NOWAIT, //write and read and return right away PIPE_UNLIMITED_INSTANCES,//The maximum number of instances that can be created for this pipe 4096 , // output time-out 4096 , // input time-out 0,//client time-out NULL); if(hPipe== INVALID_HANDLE_VALUE) { return 1;//failed } else return 0;//success } void SendMsg(string msg) { DWORD cbWritten; WriteFile(hPipe,msg.c_str(), msg.length()+1, &cbWritten,NULL); } void ProccesingPipeInstance() { while(ServerCreate() == 1)//if failed { Sleep(1000); } //if created success, wait to connect ConnectNamedPipe(hPipe, NULL); for(;;) { SendMsg("HI!"); if( ConnectNamedPipe(hPipe, NULL)==0) if(GetLastError()==ERROR_NO_DATA) { DebugPrintA("previous closed,ERROR_NO_DATA"); DisconnectNamedPipe(hPipe); ConnectNamedPipe(hPipe, NULL); } Sleep(1000); } And the C# cliend like this: static void Main(string[] args) { Console.WriteLine("Hello!"); using (var pipe = new NamedPipeClientStream(".", "HyprPipe", PipeDirection.In)) { Console.WriteLine("Created Client!"); Console.Write("Connecting to pipe server in the .dll ..."); pipe.Connect(); Console.WriteLine("DONE!"); using (var pr = new StreamReader(pipe)) { string t; while ((t = pr.ReadLine()) != null) { Console.WriteLine("Message: {0}",t); } } } } I see that the C# client connected to the .dll, but it won't receive any message.. I tried doing it the other way around, as I said before, and trying to make the C# send messages to the .dll, which would show them in a message box. The .dll was injected and connected to the C# server, but when It received a message it just crashed the application it was injected to. Please help me, or guide me on how to use named pipes between C++ and C# app

Read the article

Speed Problem with Wireless Connectivity on Cisco 877w

- by Carl Crawley

Having a bit of a weird one with my local LAN setup. I recently installed a Cisco 877W router on my DSL2+ connection and all is working really well.. Upgraded the IOS to 12.4 and my wired clients are streaming connectivity superfast at 1.3mb/s. However, there seems to be an issue with my wireless clients - I can't seem to stream any data across the local wireless connection (LAN) and using the Internet, whilst responsive enough isn't really comparable with the wired connection speed. For example, all devices are connected to an 8 Port Gb switch on FE0 from the Router with a NAS disk and on my wired clients, I can transfer/stream etc absolutely fine - however, transferring a local 700Mb file on my local LAN estimates 7-8 hours to transfer :( The Wireless config is as follows : interface Dot11Radio0 description WIRELESS INTERFACE no ip address ! encryption mode ciphers tkip ! ssid [MySSID] ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 channel 2462 station-role root rts threshold 2312 world-mode dot11d country GB indoor bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding All devices are connected to the Gb Switch which is connected to FE0 with the following: Hardware is Fast Ethernet, address is 0021.a03e.6519 (bia 0021.a03e.6519) Description: Uplink to Switch MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 14000 bits/sec, 19 packets/sec 5 minute output rate 167000 bits/sec, 23 packets/sec 177365 packets input, 52089562 bytes, 0 no buffer Received 919 broadcasts, 0 runts, 0 giants, 0 throttles 260 input errors, 260 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with dribble condition detected 156673 packets output, 106218222 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Not sure why I'm having problems on the wireless and I've reached the end of my Cisco knowledge... Thanks for any pointers! Carl

Read the article

WCF Service with callbacks coming from background thread?

- by Mark Struzinski

Here is my situation. I have written a WCF service which calls into one of our vendor's code bases to perform operations, such as Login, Logout, etc. A requirement of this operation is that we have a background thread to receive events as a result of that action. For example, the Login action is sent on the main thread. Then, several events are received back from the vendor service as a result of the login. There can be 1, 2, or several events received. The background thread, which runs on a timer, receives these events and fires an event in the wcf service to notify that a new event has arrived. I have implemented the WCF service in Duplex mode, and planned to use callbacks to notify the UI that events have arrived. Here is my question: How do I send new events from the background thread to the thread which is executing the service? Right now, when I call OperationContext.Current.GetCallbackChannel<IMyCallback>(), the OperationContext is null. Is there a standard pattern to get around this? I am using PerSession as my SessionMode on the ServiceContract. UPDATE: I thought I'd make my exact scenario clearer by demonstrating how I'm receiving events from the vendor code. My library receives each event, determines what the event is, and fires off an event for that particular occurrence. I have another project which is a class library specifically for connecting to the vendor service. I'll post the entire implementation of the service to give a clearer picture: [ServiceBehavior( InstanceContextMode = InstanceContextMode.PerSession )] public class VendorServer:IVendorServer { private IVendorService _vendorService; // This is the reference to my class library public VendorServer() { _vendorServer = new VendorServer(); _vendorServer.AgentManager.AgentLoggedIn += AgentManager_AgentLoggedIn; // This is the eventhandler for the event which arrives from a background thread } public void Login(string userName, string password, string stationId) { _vendorService.Login(userName, password, stationId); // This is a direct call from the main thread to the vendor service to log in } private void AgentManager_AgentLoggedIn(object sender, EventArgs e) { var agentEvent = new AgentEvent { AgentEventType = AgentEventType.Login, EventArgs = e }; } } The AgentEvent object contains the callback as one of its properties, and I was thinking I'd perform the callback like this: agentEvent.Callback = OperationContext.Current.GetCallbackChannel<ICallback>(); How would I pass the OperationContext.Current instance from the main thread into the background thread?

Read the article

Microsoft silverlight 5.0 features for developers

- by Jalpesh P. Vadgama

Recently on Silverlight 5.0 firestarter event ScottGu has announced road map for Silverlight 5.0. There will be lots of features that will be there in silverlight 5.0 but here are few glimpses of Silverlight 5.0 Features. Improved Data binding support and Better support for MVVM: One of the greatest strength of Silverlight is its data binding. Microsoft is going to enhanced data binding by providing more ability to debug it. Developer will able to debug the binding expression and other stuff in Siverlight 5.0. Its also going to provide Ancestor Relative source binding which will allow property to bind with container control. MVVM pattern support will also be enhanced. Performance and Speed Enhancement: Now silverlight 5.0 will have support for 64bit browser support. So now you can use that silverlight application on 64 bit platform also. There is no need to take extra care for it.It will also have faster startup time and greater support for hardware acceleration. It will also provide end to end support for hard acceleration features of IE 9. More support for Out Of Browser Application: With Siverlight 4.0 Microsoft has announced new features called out of browser application and it has amazed lots of developer because now possibilities are unlimited with it. Now in silverlight 5.0 Out Of Browser application will have ability to Create Manage child windows just like windows forms or WPF Application. So you can fill power of desktop application with your out of browser application. Testing Support with Visual Studio 2010: Microsoft is going to add automated UI Testing support with Visual Studio 2010 with silverlight 5.0. So now we can test UI of Silverlight much faster. Better Support for RIA Services: RIA Services allows us to create N-tier application with silverlight via creating proxy classes on client and server both side. Now it will more features like complex type support, Custom type support for MVVM(Model View View Model) pattern. WCF Enhancements: There are lots of enhancement with WCF but key enhancement will WSTrust support. Text and Printing Support: Silverlight 5.0 will support vector base graphics. It will also support multicolumn text flow and linked text containers. It will full open type support,Postscript vector enhancement. Improved Power Enhancement: This will prevent screensaver from activating while you are watching videos on silverlight. Silverlight 5.0 is going add that smartness so it can determine while you are going to watch video and while you are not going watch videos. Better support for graphics: Silverlight 5.0 will provide in-depth support for 3D API. Now 3D rendering support is more enhancement in silverlight and 3D graphics can be rendered easily. You can find more details on following links and also don’t forgot to view silverlight firestarter keynot video of scottgu. http://www.silverlight.net/news/events/firestarter-labs/ http://blogs.msdn.com/b/katriend/archive/2010/12/06/silverlight-5-features-firestarter-keynote-and-sessions-resources.aspx http://weblogs.asp.net/scottgu/archive/2010/12/02/announcing-silverlight-5.aspx http://www.silverlight.net/news/events/firestarter/ http://www.microsoft.com/silverlight/future/ Hope this will help you. Stay tuned!!!.

Read the article

default xna 4.0 gametime don´t works well for 2D physics

- by EusKoder

I am developing a game using Visual Studio 2010 and XNA 4.0, after advancing to some extent with the project (a platform based 2d platformer msdn starter kit) I got to test it on different computers with different hardware (CPU, graphics, etc.) and I found that the speed of movement object of the game is quite different, I implemented the PSK physics msdn that are based on time, /// <summary> /// Updates the player's velocity and position based on input, gravity, etc. /// </summary> public void ApplyPhysics(GameTime gameTime) { float elapsed = (float)gameTime.ElapsedGameTime.TotalSeconds; Vector2 previousPosition = Position; // Base velocity is a combination of horizontal movement control and // acceleration downward due to gravity. velocity.X += movement * MoveAcceleration * elapsed; velocity.Y = MathHelper.Clamp(velocity.Y + GravityAcceleration * elapsed, -MaxFallSpeed, MaxFallSpeed); velocity.Y = DoJump(velocity.Y, gameTime); // Apply pseudo-drag horizontally. if (IsOnGround) velocity.X *= GroundDragFactor; else velocity.X *= GroundDragFactor; //velocity.X *= AirDragFactor; // Prevent the player from running faster than his top speed. velocity.X = MathHelper.Clamp(velocity.X, -MaxMoveSpeed, MaxMoveSpeed); // Apply velocity. Position += velocity *elapsed; Position = new Vector2((float)Math.Round(Position.X), (float)Math.Round(Position.Y)); // If the player is now colliding with the level, separate them. HandleCollisions(gameTime); // If the collision stopped us from moving, reset the velocity to zero. if (Position.X == previousPosition.X) velocity.X = 0; if (Position.Y == previousPosition.Y) { velocity.Y = 0; jumpTime = 0.0f; } } tested eg with a PC (PC1) 2.13GHz Intel Core 2 6400 / ATI Radeon HD 4670 and another one: (pc2) 3.00GHz Intel Pentium D / Intel 82945G Express Chipset Family by displacement difference (moving x axis at supossed (position = velocity * gametime.ElapsedGameTime.TotalSeconds) constant velocity, for example) is 3 seconds in a total of 20 (example: moving pc1 player sprite 6000 pixels in the x-axis at 20 seconds and pc 2 runs the same distance in 17 ). Tested on a 3rd PC: i72700k / Gigabyte GTX 560 TI the results are even worse, after some time after starting the game gets like 3 times slower and showing the number of pixels in each frame moved in a debug window in the game (counting updatespersecond with counter variable for updates cuantity and gametime for counting a second show 63fps), it appears as if the number is always constant ( refreshments lose the Update method?). In this pc if I put the game in fullscreen during the course of the game, the effect of "go slow" is immediate and restore window mode sometimes yield returns to "normal" and sometimes not. Eventually I began to try a new project to test whether the movement is constant in different pc loading only one sprite and its position value in screen printing. Occur The same. I even tried moving a constant amount of pixels explicitly (position + = 5) and different speeds in different pc quantities of pixels moved in x time. I have the game loop as the default (fixedTimeStep=true;SynchronizeWithVerticalRetrace=true;). I've also tried turning off and creating another timestep as discussed in different post (eg http://gafferongames.com/game-physics/fix-your-timestep/ but i can´t achieve the desired result, move the same number of pixels in X seconds on different computers with windows. All pc used for tests use windows 7 enterprise pc1 == x86 the others are x64. The weirdest thing is that I find information about people describing the same problem and that I wear long nights of searches. Thanks for your help.

Read the article

Add a Hovering Image Toolbar to Firefox

- by Asian Angel

When you work with webpage images in Firefox you normally have to use the Context Menu to do anything with them. The Image Toolbar extension provides an extra toolbar to use when you hover your mouse over webpage images. Note: This extension will not function if you have the NoScript extension installed/enabled unless JavaScript has permission to be active on that page. Before You can see the available “Context Menu” options for working with images here. Not bad but it would be nice if some other convenient options were available as well. Image Toolbar in Action Once you have installed the extension you will be able to view the toolbar whenever you hover your mouse over an image. All of the commands are active by default but you can choose what is available in the options. The toolbar will also appear in the upper left region of the image but can be set to appear relative to the cursor. Note: The default minimum image size for the toolbar to appear over is “260 x 260 pixels” so you will probably want to change it to a much smaller size (see options below). Here is what is available in the Image Toolbar: Save – Choose between being prompted when saving or automatically saving to a specified location Copy – Copies image and image URL so that you can paste the image or URL depending on the app pasted into Print – Provides print preview and printing capabilities Info – Opens a window with “properties information” about the image Folder – Opens browser’s download folder in Windows Explorer The “Save, Copy, Print, & Folder Commands” are all pretty clear in what you can expect from them but what about the “Info Command”? This is what you will see if you use the “Info Command” and expand the window out all the way. Very nice… Options There are quite a few options available for what appears to be such a small toolbar. The first “Tab Area” lets you set up the “Save Scheme” that best suits your personal needs. You can choose which commands are available in the toolbar, decide if you would like text labels visible, and enable small icons if desired. As mentioned above the default image size for the toolbar to appear is “260 x 260 pixels”…we set ours for “10 x 10 pixels”. If you would like the toolbar to appear relative to your mouse cursor as opposed to the upper left corner of the image then you can select for that here. Conclusion If you have been wanting more options for working with webpage images in Firefox then this will make a very useful and convenient addition to your browser. Links Download the Image Toolbar extension (Mozilla Add-ons) Similar Articles Productive Geek Tips Conserve Space in Firefox by Combining ToolbarsShow Alexa Ranking in FirefoxLightweight Extension to Show PageRank in FirefoxSwitch Windows by Hovering the Mouse Over a Window in Windows 7 or VistaQuick Tip: Show PageRank in Firefox while Google Toolbar is Hidden TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Roadkill’s Scan Port scans for open ports Out of 100 Tweeters Out of band Security Update for Internet Explorer 7 Cool Looking Screensavers for Windows SyncToy syncs Files and Folders across Computers on a Network (or partitions on the same drive) If it were only this easy

Search Results

Search found 2519 results on 101 pages for 'duplex printing'.

Page 83/101 | < Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90 | Next Page >

- by Harvey

- by Ed

- by Daniel

- by Sid

- by Michael Donohue

- by TheDayIsDone

- by DKNUCKLES

- by Pekka

- by big_smile

- by user69670

- by ezz9

- by Vince Radice

- by user60622

- by ilan123

- by MarkPearl

- by zewone

- by vafa

- by Lerp

- by arungupta

- by Gal

- by Carl Crawley

- by Mark Struzinski

- by Jalpesh P. Vadgama

- by EusKoder

- by Asian Angel

< Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90 | Next Page >