Search Results

Search found 23265 results on 931 pages for 'justin case'.

Page 831/931 | < Previous Page | 827 828 829 830 831 832 833 834 835 836 837 838  | Next Page >

  • Low FPS in some games, but hardware not fully used

    - by Mario De Schaepmeester
    I just did a little funny experiment in the game/sim "Train Simulator 2013". I normally have good FPS in it (around 30) at full settings. What I did was make a really, really long train so that the calculations the sim needed to make were enormous (the sim is quite realistic, it takes all things into account like speed/acceleration, G-forces, comfort levels, possible wheel slip and many more, and most of those things on each carriage seperately). This resulted in only 14FPS as reported by the game, but it felt more like 8FPS or so. I have a Logitech G15 keyboard which has an LCD, and it allows me to monitor CPU/RAM and video card load on it. The strange thing is, all CPU cores were busy, but the total load was only about 60% maximum at all times. The video card was only on 30% load (possibly an important note, the memory was full, which is however not unusual for the game in question). The RAM had plenty of room and there weren't many operations as it didn't grow or shrink much. I just have the feeling that the game would run smoother if it used more of my hardware power. Why is it not doing so? I had the same in another game, The Elder Scrolls: Morrowind when using more than 100 mods (that all use scripting) and a few high res texture mods, + a full-on graphics improvement program. The engine is very old (2003), and so I thought this might be the cause (not being optimised for multithreading). I had thought of possible causes, like: The operating system doesn't let the games use all the resources. It doesn't make use of multi-threading appropriately. To eliminate the former, I tried a CPU stress tool and that got 100% CPU juice as I let it run, so the OS is not the problem. I gave its thread the "higher" priority though. My actual question In both games, I did things the engine was not really built to do or support. Can those games' framerate be limited cause of their own engine not being able to cope? What is the real reason and more importantly, can I help it? And in any case, could something actually be wrong with my hardware? It's all reasonably new, a couple of months, and I (almost) never experience any other trouble. Modern and much more demanding games work absolutely fine. Specs CPU: AMD Phenom II 965 X4 @ 3.4gHz RAM: 8GB of DDR3 RAM Video: MSI GTX560 (nVidia chip) with 1GB of GDDR5 memory OS: Windows 7 Ultimate 64 bit Nothing overclocked.

    Read the article

  • ssh, "Last Login", `last` and OS X

    - by allentown
    I have hit the googles as much as I can on this, being specific to OS X, I am not finding an answer. Nothing is wrong, but curiosity levels are high. $ssh [email protected] Password: Last login: Wed Apr 7 21:28:03 2010 from my-laptop.local ^lonely tylenol^ Line 1 is my command line 2 is the shell asking for the password line 3 is where my question comes from line 4 comes out of /etc/motd I can find nothing in ~/ of an of the .bash* files that contains the string "Last Login", and would like to alter it. It performs some type of hostname lookup, which I can not determine. If I ssh to another host: $ssh [email protected] Last login: Wed Apr 7 21:14:51 2010 from 123-234-321-123-some.cal.isp.net.example hi there, you are on box 456 line 1 is my command line 2 is again, where my question comes from line 3 is from /etc/motd *The dash'd IP address is not reversed On this remote host, I have ~/.ssh and it's corresponding keys set up, so there was no password request Where is the "Last Login:" coming from, where does the date stamp come from, and most importantly, where does the hostname come from? While on [email protected] (box 456) $echo hostname remote.location.example456.com Or with dig, to make sure I have rDNS/PTR set up, for which I am not authoritative, but my ISP has correctly set... $dig -x 123.234.321.123 PTR remote.location.example456.com or $dig PTR 123.321.234.123.in-addr.arpa. +short remote.location.example456.com. my previous hostname used to be 123-234-321-123-some.cal.isp.net.example, which I set with hostname -s remote.location.example456.com, because it was obnoxious to see such a long name. That solves the value of $echo hostname which now returns remote.location.example456.com. Mac OS X, 10.6 is this case, does seem to honor: touch ~/.hushlogin If leave that file empty, I get nothing on the shell when I login. I want to know what controls the host resolution of the IP, and how it is all working. For example, running last reports a huge list of my logins, which have obtusely long hostnames, when they would be preferable to just be remote.location.example456.com. More confusing to me, reading the man page for wtmp and lastlog, it looks like lastlog is not used on OS X, /var/log/lastlog does not exist. Actually, none of these exist on 10.5 or 10.6: /var/run/utmp The utmp file. /var/log/wtmp The wtmp file. /var/log/lastlog The lastlog file. If I am to assume that the system is doing some kind of reverse lookup, I certainly do not know what it is, as it is not an accurate one.

    Read the article

  • What is the difference between running a Windows service vs. running through shell?

    - by Zack
    I am trying to troubleshoot an issue on a Windows 2008 server where running attempting to connect to a "Timberline Data Source" ODBC driver crashes if the call is in a "service" context, but succeeds if the call is initiated manually in a Remote Desktop session. I have set the service to run as my user. I'm wondering if, all else being equal (user, machine, etc), are there any fundamental security/environment differences between running a process as a service vs manually? --- Implementation Details --- In case it is helpful for anyone, I had a system that started as an attempt to connect to a Timberline Database using ODBC and a Python CGI script called via IIS 7. The script itself works fine, however, as soon as I attempt to perform the ODBC connect function, the script crashes without throwing an exception. The script was able to connect fine when executed via command line. The same thing happened when using a C#/.net service, attempting to run via Apache, Windows Scheduler or even a 3rd party scheduling tool. With the last option (the 3rd party scheduling tool, pycron) I set the service up log in as my user and had the same issue (I confirmed via Task Manager that the process running user was, in fact, me). It just doesn't make sense to me why a service, which should be running as my user, appears to still be operating in a different security context or environment. Also, if it's important, the Timberline database is referenced by computer name on the network ("\\timberline-server\Timberline Office\Accounts\AT" or something to that effect) I also realized that, as Joel pointed out, the server DOES have a mapped drive ("Y:" which is mapped to "\\timberline-server\Timberline Office") The DSN is set up at the "System DSN" level which, according to the ODBC Administration Tool, means that the DSN is available to users and services Since I'm not allowed to answer this question yet, I'll post the solution that I arrived on: As Joel Coel mentioned, there actually was a mapped drive scenario. I didn't realize this because the DSN specified a path using UNC. However, it seems as though the actual Timberline Driver referred to a mapped drive. Since services don't start with the mapped drive, I was forced to add the drive mapping code into my service. Since it was written in python, I used code from a Stackoverflow answer that was able to map the drive on the fly.

    Read the article

  • Troubleshooting Network Speeds -- The Age Old Inquiry

    - by John K
    I'm looking for help with what I'm sure is an age old question. I've found myself in a situation of yearning to understand network throughput more clearly, but I can't seem to find information that makes it "click" We have a few servers distributed geographically, running various versions of Windows. Assuming we always use one host (a desktop) as the source, when copying data from that host to other servers across the country, we see a high variance in speed. In some cases, we can copy data at 12MB/s consistently, in others, we're seeing 0.8 MB/s. It should be noted, after testing 8 destinations, we always seem to be at either 0.6-0.8MB/s or 11-12 MB/s. In the building we're primarily concerned with, we have an OC-3 connection to our ISP. I know there are a lot of variables at play, but I guess I was hoping the experts here could help answer a few basic questions to help bolster my understanding. 1.) For older machines, running Windows XP, server 2003, etc, with a 100Mbps Ethernet card and 72 ms typical latency, does 0.8 MB/s sound at all reasonable? Or do you think that slow enough to indicate a problem? 2.) The classic "mathematical fastest speed" of "throughput = TCP window / latency," is, in our case, calculated to 0.8 MB/s (64Kb / 72 ms). My understanding is that is an upper bounds; that you would never expect to reach (due to overhead) let alone surpass that speed. In some cases though, we're seeing speeds of 12.3 MB/s. There are Steelhead accelerators scattered around the network, could those account for such a higher transfer rate? 3.) It's been suggested that the use SMB vs. SMB2 could explain the differences in speed. Indeed, as expected, packet captures show both being used depending on the OS versions in play, as we would expect. I understand what determines SMB2 being used or not, but I'm curious to know what kind of performance gain you can expect with SMB2. My problem simply seems to be a lack of experience, and more importantly, perspective, in terms of what are and are not reasonable network speeds. Could anyone help impart come context/perspective?

    Read the article

  • Server to server replication and CPU and 32k\ corrupt doc

    - by nick wall
    Summary: if database contains a doc with 32K issue or corrupt, on server to server replication it causes marked increase in CPU in nserver.exe task, which effectively causes our server(s) to slow right down. We have a 5 server cluster (1 "hub" and 4 HTTP servers accessed via reverse proxy and SSO for load balancing and redundancy). All are physically located next to each other on network, they don't have dedicated network\ ports for cluster or replication. I realise IBM recommendation is dedicated port for cluster. Cluster queues are in tolerance and under heavy application user load, i.e. the maximum number of documents are being created, edited, deleted, the replication times between servers are negligible. Normally, all is well. Of the servers in the cluster, 1 is considered the "hub", and imitates a PUSH-PULL replication with it's cluster mates every 60mins, so that the replication load is taken by the hub and not cluster mates. The problem we have: every now and then we get a slow replication time from the hub to a cluster mate, sometimes up to 30mins. This maxes out the nserver.exe task on the "cluster mate" which causes it to respond to http requests very slowly. In the past, we have found that if a corrupt document is in the DB, it can have this affect, but on those occasions, the server log will show the corrupt doc noteId, we run fixup, all well. But we are not now seeing any record of corrupt docs. What we have noticed is if a doc with the 32K issue is present, the same thing can happen. Our only solution in that case is to run a : fixup mydb.nsf -V, which shows it is purging a 32K doc. Luckily we run a reverse proxy, so we can shut HTTP servers down without users noticing, but users do notice when a server has the problem! Has anyone else seen this occur? I have set up DDM event handlers for many of the replication events. I have set the replication time out limit to 5 mins (the max we usually see under full user load is 0.1min), to prevent it rep'ing for 30mins as before. This ia a temporary work around. Does anyone know of a DDM event to trap the 32K issue? we could at least then send alert. Regarding 32K issue: this prob needs another thread, but we are finding this relatively hard to find the source of the issue as the 32K event is fairly rare. Our app is fairly complex, interacting with various other external web services, with 2 way data transfer. But if we do encounter a 32K doc, we can't look at field properties, so we can't work out which field has issue which would give us a clue as to which process is culprit. As above, we run a fixup -V. Any help\ comments on this would be gratefully received.

    Read the article

  • Beginner server local installation

    - by joanjgm
    Here's the thing I own a small business and currently my emails are being managed by some regular hosting using cpanel and that I bought a small server and installed windows server and exchange Can you tell what I did wrong here Installed and configured my current existing domain Configured all email address Installed noip in case my public address change In the cpanel of the domain I've added an MX record to the noip domain of the server with priority 0 so now emails are being received by my own server Now whenever I send an email to anyone gmail hotmail etc I get a response that cannot be delivered since may be junk This didn't happen when I sent emails from the hosting What's missing what did I do wrong heres the code mx.google.com rejected your message to the following e-mail addresses: Joan J. Guerra Makaren ([email protected]) mx.google.com gave this error: [186.88.202.13 12] Our system has detected that this message is likely unsolicited mail. To reduce the amount of spam sent to Gmail, this message has been blocked. Please visit http://support.google.com/mail/bin/answer.py?hl=en&answer=188131 for more information. cn9si815432vcb.71 - gsmtp Your message wasn't delivered due to a permission or security issue. It may have been rejected by a moderator, the address may only accept e-mail from certain senders, or another restriction may be preventing delivery. Diagnostic information for administrators: Generating server: SERVERMEGA.megaconstrucciones.com.ve [email protected] mx.google.com #550-5.7.1 [186.88.202.13 12] Our system has detected that this message is 550-5.7.1 likely unsolicited mail. To reduce the amount of spam sent to Gmail, 550-5.7.1 this message has been blocked. Please visit 550-5.7.1 http://support.google.com/mail/bin/answer.py?hl=en&answer=188131 for 550 5.7.1 more information. cn9si815432vcb.71 - gsmtp ## Original message headers: Received: from SERVERMEGA.megaconstrucciones.com.ve ([fe80::9096:e9c2:405b:6112]) by SERVERMEGA.megaconstrucciones.com.ve ([fe80::9096:e9c2:405b:6112%10]) with mapi; Thu, 29 May 2014 11:32:19 -0430 From: prueba <[email protected]> To: "Joan J. Guerra Makaren" <[email protected]> Subject: Probando correos Thread-Topic: Probando correos Thread-Index: Ac97V1eW4OBFmoqJTRGoD7IPTC2azg== Date: Thu, 29 May 2014 16:04:35 +0000 Message-ID: <[email protected]> Accept-Language: en-US, es-VE Content-Language: en-US X-MS-Has-Attach: X-MS-TNEF-Correlator: Content-Type: multipart/alternative; boundary="_000_000f42494487966276f7b241megaconstruccionescomve_" MIME-Version: 1.0

    Read the article

  • netbook intel GMA 3150 external monitor 1920x1080 flicker problem

    - by seyenne
    Dear all, i recently purchased a acer netbook (apsire one d260). It runs flawlessly. Yesterday I bought a samsung 23" TFT with a native resolution of 1920x1080. According to the information found in the internet and my local computer dealer, the intel chipset can handle the native resolution of the monitor. However, this is only partly the case. I use the VGA cabel to connect, the monitor instantly switches to the native resolution and now the problem: Occasionaly, especially the first 2 hours after booting up, I have a flickering all over the screen, sometimes the entire screen is shaking and spinning around like crazy. I figured out, that lowering the resolution avoids the flicker but this helps only for some time. I can rule out that it's the monitor's problem since I found no issues with another notebook. Right now, I have no problems with the netbook, for about 30 minutes I didn't experience any issues... But I don't know for how long, it occurs without warning :-) I'm worried that if I would bring the netbook back to the dealer and explain my problem, after testing it on an external screen in the local shop, everything works just fine... And I won't get helped with the problem because I can't prove it. (I'm currently in Thailand and over here, customer service is nothing like back home in Germany) What can I do? Is this a driver related issue? (I installed the latest GPU driver) Is it because of the VGA cable? (But why does it work sometimes without any problems and with no issues on the other notebook) I monitored the GPU/CPU temperature, nothing changes really over time..Can it simply be a faulty GPU and is a replacement justifiable? I'm really stressed now because for the time I'm writing, the flickering didn't occur...but for sure, soon or later it will happen again.. I Forgot to mention, the problem also happens if the netbook runs on battery, unplugged. So the only hardware that is plugged is the TFT screen. ...........and here it comes again, flickering has just begun. NEED HELP! Thank you all for reading through this and giving any suggestions if possible. Cheers

    Read the article

  • how can I give openvpn clients access to a dns server (bind9) that is located on the same machine as the openvpn server

    - by lacrosse1991
    I currently have a debian server that is running an openvpn server. I also have a dns server (bind9) that I would like give allow access to by the connected openvpn clients, but I am unsure as of how to do this, I already known how to send dns options to the clients using push "dhcp-option DNS x.x.x.x" but I am just unsure how give the clients access to the dns server that is located on the same machine as the vpn server, so if anyone could point me in the right direction I would really appreciate it. Also in case this would have anything to do with adding rules to iptables, this is my current configuration for iptables # Generated by iptables-save v1.4.14 on Thu Oct 18 22:05:33 2012 *nat :PREROUTING ACCEPT [3831842:462225238] :INPUT ACCEPT [3820049:461550908] :OUTPUT ACCEPT [1885011:139487044] :POSTROUTING ACCEPT [1883834:139415168] -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE COMMIT # Completed on Thu Oct 18 22:05:33 2012 # Generated by iptables-save v1.4.14 on Thu Oct 18 22:05:33 2012 *filter :INPUT ACCEPT [45799:10669929] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [45747:10335026] :fail2ban-apache - [0:0] :fail2ban-apache-myadmin - [0:0] :fail2ban-apache-noscript - [0:0] :fail2ban-ssh - [0:0] :fail2ban-ssh-ddos - [0:0] :fail2ban-webserver-w00tw00t - [0:0] -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-apache-myadmin -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-webserver-w00tw00t -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-apache-noscript -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-apache -A INPUT -p tcp -m multiport --dports 22 -j fail2ban-ssh-ddos -A INPUT -p tcp -m multiport --dports 22 -j fail2ban-ssh -A INPUT -i tun+ -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 3306 -j ACCEPT -A FORWARD -i tun+ -j ACCEPT -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT -A fail2ban-apache -j RETURN -A fail2ban-apache-myadmin -s 211.154.213.122/32 -j DROP -A fail2ban-apache-myadmin -s 201.170.229.96/32 -j DROP -A fail2ban-apache-myadmin -j RETURN -A fail2ban-apache-noscript -j RETURN -A fail2ban-ssh -s 76.9.59.66/32 -j DROP -A fail2ban-ssh -s 64.13.220.73/32 -j DROP -A fail2ban-ssh -s 203.69.139.179/32 -j DROP -A fail2ban-ssh -s 173.10.11.146/32 -j DROP -A fail2ban-ssh -j RETURN -A fail2ban-ssh-ddos -j RETURN -A fail2ban-webserver-w00tw00t -s 217.70.51.154/32 -j DROP -A fail2ban-webserver-w00tw00t -s 86.35.242.58/32 -j DROP -A fail2ban-webserver-w00tw00t -j RETURN COMMIT # Completed on Thu Oct 18 22:05:33 2012 also here is my openvpn server configuration port 1194 proto udp dev tun ca ca.crt cert server.crt key server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt keepalive 10 120 comp-lzo user nobody group users persist-key persist-tun status /var/log/openvpn/openvpn-status.log verb 3 push "redirect-gateway def1" push "dhcp-option DNS 213.133.98.98" push "dhcp-option DNS 213.133.99.99" push "dhcp-option DNS 213.133.100.100" client-to-client

    Read the article

  • vmdk to live cd - VMware vmxnet virtual NIC driver Kernel panic

    - by ronalchn
    Task I am trying to convert a virtual machine to a live CD. Specifically, the virtual machine I am trying to convert is the IOI 2013 Competition Environment. In this task, I am aided by a guide Converting a virtual disk image: VDI or VMDK to an ISO you can distribute. Symptoms However, after getting through all the instructions, the live CD causes a kernel panic on boot on bare metal. In particular, the screen shows: [0.737348] cdrom: Uniform CD-ROM driver Revision: 3.20 [0.737503] sr 3:0:0:0: >Attached scsi CD-ROM sr0 [0.737638] sr 3:0:0:0: >Attached scsi generic sg2 type 5 [0.737771] Freeing unused kernel memory: 756k freed [0.738093] Write protecting the kernel text: 5960k [0.738155] Write protecting the kernel read-only data: 2424k [0.738224] NX-protecting the kernel data: 4280k Loading, please wait... [0.752252] udevd[100]: starting version 175 [0.768708] VMware vmxnet3 virtual NIC driver - version 1.1.29.0-k-NAPI [0.781204] VMware PVSCSI driver - version 1.0.2.0-k [0.789555] VMware vmxnet virtual NIC driver [0.799356] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200 [0.799356] [0.799472] Pid: 1, comm: init Tainted: G 0 3.5.0-17-generic #28-Ubuntu [0.799549] Call Trace: [0.799603] [<c15bf0ec>] panic+0x81/0x17b [0.799654] [<c104a6a5>] do_exit+0x745/0x7a0 [0.799707] [<c104a9a4>] do_group_exit+0x34/0xa0 [0.799760] [<c104aa28>] sys_exit_group+0x18/0x20 [0.799813] [<c15cff5f>] sysenter_do_call+0x12/0x28 Possible problem I suspect that the problem is the VMware vmxnet virtual NIC driver - however, I do not know how I can uninstall it, and possibly install one for a bare metal machine. If anyone knows which packages needs installing/uninstalling at the .rootfs/ chroot directory stage, please let me know. Details on procedure Do note that after importing the .ova file into Virtualbox, the virtual machine is stored as a .vmdk file already, and not a .vdi file. I would like to point out some results of the procedure followed in case of any questions. This is after extracting the filesystem from the .raw file to the .rootfs/ directory mentioned in the blog. I changed the filesystem table as mentioned in the blog, then looked at the possible "kernel optimized for virtualization". However, I found that linux-image-generic was already installed. Also, when running the command dpkg-query --showformat='${Package}\n' -W 'vmware-tools*' (or dpkg-query --showformat='${Package}\n' -W '*-virtual'), no packages were found. Thus, I did not find any virtualization specific packages. I proceeded to generate the iso following the steps in the blog, and burned it to a DVD.

    Read the article

  • Connection closed by remote host followed by Connection refused

    - by Khosrow
    All of a sudden my ssh connection to server has been damaged. Here is what's happened: $ ssh -vvv -p <PORT> -l <USER> <HOST> OpenSSH_5.3p1 Debian-3ubuntu7, OpenSSL 0.9.8k 25 Mar 2009 debug1: Reading configuration data /home/khosrow/.ssh/config debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to <HOST> [<IP>] port <PORT>. debug1: Connection established. debug1: identity file /home/khosrow/.ssh/identity type -1 debug1: identity file /home/khosrow/.ssh/id_rsa type -1 debug1: identity file /home/khosrow/.ssh/id_dsa type -1 ssh_exchange_identification: Connection closed by remote host I've recently updated the box with yum update and sshd got updated as well. I honestly don't know if this caused any damages or not. But it's prompted that /etc/ssh/sshd_config was stored as /etc/ssh/sshd_config.rpmnew which was quite normal. I've seen similar posts while googling, but almost all of them suggests that I should check /etc/hosts.allow and /etc/hosts.deny, which in my case, I can't. I can not connect to the box to see what's going on there. I rebooted the box, through web interface of server provider, and it even got worse. I'm now getting this: $ ssh -vvv -p <PORT> -l <USER> <HOST> OpenSSH_5.3p1 Debian-3ubuntu7, OpenSSL 0.9.8k 25 Mar 2009 debug1: Reading configuration data /home/khosrow/.ssh/config debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to <HOST> [<IP>] <PORT>. debug1: connect to address <IP> port <PORT>: Connection refused ssh: connect to host <HOST> port <PORT>: Connection refused with both <CUSTOM_PORT> and default 22 ports. I would really appreciate if anyone could help me on this.

    Read the article

  • Is the guideline: don't open email attachments or execute downloads or run plug-ins (Flash, Java) from untrusted sites enough to avert infection?

    - by therobyouknow
    I'd like to know if the following is enough to avert malware as I feel that the press and other advisory resources aren't always precisely clear on all the methods as to how PCs get infected. To my mind, the key step to getting infected is a conscious choice by the user to run an executable attachment from an email or download, but also viewing content that requires a plug-in (Flash, Java or something else). This conscious step breaks down into the following possibilities: don't open email attachments: certainly agree with this. But lets try to be clear: email comes in 2 parts -the text and the attachment. Just reading the email should not be risky, right? But opening (i.e. running) email attachments IS risky (malware can be present in the attachment) don't execute downloads (e.g. from sites linked from in suspect emails or otherwise): again certainly agree with this (malware can be present in the executable). Usually the user has to voluntary click to download, or at least click to run the executable. Question: has there ever been a case where a user has visited a site and a download has completed on its own and run on its own? don't run content requiring plug-ins: certainly agree: malware can be present in the executable. I vaguely recall cases with Flash but know of the Java-based vulnerabilities much better. Now, is the above enough? Note that I'm much more cautious than this. What I'm concerned about is that the media is not always very clear about how the malware infection occurs. They talk of "booby-trapped sites", "browser attacks" - HOW exactly? I'd presume the other threat would be malevolent use of Javascript to make an executable run on the user's machine. Would I be right and are there details I can read up on about this. Generally I like Javascript as a developer, please note. An accepted answer would fill in any holes I've missed here so we have a complete general view of what the threats are (even though the actual specific details of new threats vary, but the general vectors are known).

    Read the article

  • Incremental RPM package version "numbers" for x.y.z > x.y.z-beta (or alpha, rc, etc)

    - by Jonathan Clarke
    In order to publish RPM packages of several different versions of some software, I'm looking for a way to specify version "numbers" that are considered "upgrades", and include the differentiation of several pre-release versions, such as (in order): "2.4.0 alpha 1", "2.4.0 alpha 2", "2.4.0 alpha 3", "2.4.0 beta 1", "2.4.0 beta 2", "2.4.0 release candidate", "2.4.0 final", "2.4.1", "2.4.2", etc. The main issue I have with this is that RPM considers that "2.4.0" comes earlier than "2.4.0.alpha1", so I can't just add the suffix on the end of the final version number. I could try "2.4.0.alpha1", "2.4.0.beta1", "2.4.0.final", which would work, except for the "release candidate" that would be considered later than "2.4.0.final". An alternative I considered is using the "epoch:" section of the RPM version number (the epoch: prefix is considered before the main version number so that "1:2.4.0" is actually earlier than "2:1.0.0"). By putting a timestamp in the epoch: field, all the versions get ordered as expected by RPM, because their versions appear to increment in time. However, this fails when new releases are made on several major versions at the same time (for example, 2.3.2 is released after 2.4.0, but their version for RPM are "20121003:2.3.2" and "20120928:2.4.0" and systems on 2.3.2 can't get "upgraded" to 2.4.0, because rpm sees it as an older version). In this case, yum/zypper/etc refuse to upgrade to 2.4.0, thus my problem. What version numbers can I use to achieve this, and make sure that RPM always considers the version numbers to be in order. Or if not version numbers, other mechanism in RPM packaging? Note 1: I would like to keep the "Release:" field of the spec file for it's original purpose (several releases of packages, including packaging changes, for the same version of the packaged software). Note 2: This should work on current production versions of major distributions, such as RHEL/CentOS 6 and SLES 11. But I'm interested in solutions that don't, too, so long as they don't involve recompiling rpm! Note 3: On Debian-like systems, dpkg uses a special component in the version number which is the "~" (tilde) character. This causes dpkg to count the suffix as "negative" ordering, so that "2.4.0~anything" will come before "2.4.0". Then, normal ordering applies after the "~", so "2.4.0~alpha1" comes before "2.4.0~beta1" because "alpha" comes before "beta" alphabetically. I'm not necessarily looking to use the same scheme for RPM packages (I'm pretty sure no such equivalent exists), so this is just FYI.

    Read the article

  • Computer randomly reboots during "intensive activity".

    - by Reznor
    My friend has been playing games on his new build for some time now. However, lately, his computer will randomly reboot out of nowhere, so far only happening in game, and presumably only to happen in game as it happens nowhere else. This can happen in game during play or even in the options. Note, it isn't a crash or blue screen. It's just a normal reboot. This started today, I believe, and has only occured in two games: Dead Space and Stalker: Shadow of Chernobyl. He has played a handful of games before these, for about a week or so, without this problem. We theorized on two possibilities: Maybe something is overheating? Maybe the power supply is inadequate? These two were quickly dismissed, as all his components were operating at normal temperatures when he got back to his desktop from the reboot, and we all know these parts don't exactly cool down quickly, especially if they get hot enough to trigger a reboot. Besides, I know at-least my motherboard reports processor overheating at start-up, and requests I press f1 to continue into boot. The PSU one was dismissed too. He has an 850w power supply on a rig that was estimated to take only 720 some watts, that's with some overcompensating to be safe. He opened up his case to make sure nothing was seated wrong or in the way. All was fine, but he did notice a sticker on his video card. It had a giant barcode on it and some numbers. Now, I'm used to seeing these stickers, they're the warranty stickers, right, and removal voids the warranty? Yeah, well, we find it odd because this sticker is slapped right over the circuits of the video card, not on a block or anything. Is this normal? Should he remove it? Right now, I am concerned with the memory. Could that be at fault? Here are his specs: Windows 7 Home Premium, 64-Bit Intel i7 950 EVGA GeForce 570 GTX 4 GB DDR3 PC10666 dual-channel Corsair RAM Corsair 850w PSU Gigabyte GA-X58A-UD3R Western Digital 1 TB WD1001FALS

    Read the article

  • Other processes take over port 80 when restarting Apache - why, and how to solve?

    - by user72149
    I have a CentOS 5.5 server running Apache on port 80 as well as some other applications. All works fine until I for some reason need to restart the httpd process. Doing so returns: sudo /etc/init.d/httpd restart Stopping httpd: [ OK ] Starting httpd: (98)Address already in use: make_sock: could not bind to address [::]:80 (98)Address already in use: make_sock: could not bind to address 0.0.0.0:80 no listening sockets available, shutting down Unable to open logs First I thought perhaps httpd had frozen and was still running, but that was not the case. So I ran netstat to find out what was using port 80: sudo netstat -tlp Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 *:7203 *:* LISTEN 24012/java tcp 0 0 localhost.localdomain:smux *:* LISTEN 3547/snmpd tcp 0 0 *:mysql *:* LISTEN 21966/mysqld tcp 0 0 *:ssh *:* LISTEN 3562/sshd tcp 0 0 *:http *:* LISTEN 3780/python26 Turns out that my python process had taken over listening to http in the instant that httpd was restarting. So, I killed python and tried starting httpd again - but ran into the same error. Netstat again: sudo netstat -tlp Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 *:7203 *:* LISTEN 24012/java tcp 0 0 localhost.localdomain:smux *:* LISTEN 3547/snmpd tcp 0 0 *:mysql *:* LISTEN 21966/mysqld tcp 0 0 *:ssh *:* LISTEN 3562/sshd tcp 0 0 *:http *:* LISTEN 24012/java Now my java process had taken over listening to http. I killed that too and could then successfully restart httpd. But this is a terrible workaround. Why will these python and java processes start listening to port 80 as soon as httpd is restarted? How to solve? Two other comments. 1) Both java and python processes are started by apache from a php script. But when apache is restarted, they should not be affected. And 2) I have the same setup on two other machines running Ubuntu and there's no problem there. Any ideas? Edit: The Java process listens to port 7203 and the python process supposedly doesn't listen to any port. For some reason, they start listening to port 80 when apache is restarted. This hasn't happened before. On Ubuntu it runs fine. For some reason, on my current CentOS 5.5 machine, this problem arises.

    Read the article

  • 2 servers, high availability and faster response

    - by user17886
    I recently bought a second webserver because I worry about hardware failure of my old server. Now that I have that second server I wish to do a little more then just have one server standby and replicate all day. As long as it's there I might as well get some advantage our of it ! I have a website powered by ubuntu 12.04, nginx, php-fpm, apc, mysql (5.5) and couchdb. Im currently testing configurations where i can achieve failover AND make good use of the extra harware for faster responses / distributed load. The setup I am testing nowinvolves heartbeat for ip failover and two identical servers. Of the two servers only one has a public ip adress. If one server crashes the other server takes over the public ip adress. On an incoming request nginx forwards the request tot php-fpm to either server a of server b (50/50 if both servers are alive). Once the request has been send to php-fpm both servers look at localhost for the mysql server. I use master-master mysql replication for this. The file system is synced with lsyncd. This works pretty well but Im reading it's discouraged by the (mysql) community. Another option I could think of is to use one server as a mysql master and one server as a web/php server. The servers would still sync their filesystem, would still run the same duplicate software (nginx,mysql) but master slave mysql replication could be used. As long as bother servers are alive I could just prefer nginx to listen to ip a and mysql to ip b. If one server is down, the other server could take over the task of the other server, simply by ip switching. But im completely new at this so I would greatly value your expert advice. Is either of the two setups any good ? If you have any thoughts on this please let me know ! PS, virtualisation, hosting on different locations or active/passive setups are not solutions im looking for. I find virtual server either too slow or too expensive. I already have a passive failover on another location. But in case of a crash I found the site was still unreachable for too long due to dns caching.

    Read the article

  • Wrapping a point-to-point link

    - by user3712955
    I'm using a pair of IP radios (non-WiFi) to bridge my office engineering LAN (172.0.0.0/8) to a lab in another building. The radios work fine, but they expose a web management interface I'd like to hide, and they also generate traffic (ARP, STP, and more) that I need to keep off my (very, very clean) LAN segments. I have some ARM-Linux boards (similar to Beagle/Panda/RasPi) running Ubuntu, and I've put one at each end of the link, between the radio and the LAN. Each of the boards has 2 wired Ethernet interfaces, eth0 and eth1. The LAN segments are connected to eth0, and the radios are connected to eth1. I'd like to accomplish the following: Keep radio-originated traffic off my LAN segments! Hide all services provided by the radio (web, ssh, etc.) Transparently pass all traffic between the LAN segments (including things like ARP). The above also applies to the ARM-Linux boards: No stray traffic my LAN from them either! I'd like the system to look like a switch: LAN packets arriving at one eth0 appear at the other. And neither eth0 should have an IP address: The working system should behave like a CAT6 cable with some latency (instead of ARM boards and radios). Unfortunately, I'm confused about how to properly configure the ARM Ubuntu systems. What I'm guessing I need is a bridge on each board (br0?) and a VLAN (vlan0 or eth0.0?) to isolate the LAN traffic from everything else as it passes through the ARM boards and the radios. Then I need some kind of a firewall to block sending anything out eth0 that isn't from the other eth0 (via the VLAN). I've looked at the ip and ebtables commands (especially -t broute). While the concepts sorta-kinda make sense, I'm completely lost in the details. Edit: In the perverse case that a system on one of my LAN segments has the same IP address as one of the radios, or as eth1 on the ARM-Ubuntu boards, a VLAN won't work. Which I believe means I need to tunnel all traffic between the two eth0 interfaces to get that "like a wire" behavior. Help? Finally, I'd like to have a way to temporarily expose services on the ARM boards (ssh) and the radios (web) for maintenance purposes. Ideally, it would expose an IP address with ssh available on port 22. Once connected, I figure I'd start an X11 session and run a browser on the ARM board to access the radios. Or something. I could login via the console to enable/disable this, or perhaps could use a GPIO to trigger a script. I feel I've identified most of the pieces needed to make all this happen, but I have no idea how to combine them to make a working system. Thanks!

    Read the article

  • What server setup for a small web development company? [closed]

    - by Giordano
    I co-own a company with a friend of mine and we have decided to buy a new server to support our business (our current server is an Asus EEE Box, working great but too limited :) ). I should mention that we are web developers but occasionally we do small-office sys admin. Thus, 99% of time we work on GNU/Linux (mainly Ubuntu) but from time to time we need to setup a Windows environment to assist some customers (e.g. setup a temporary SQL Server 2008). Our requirements: Low budget: we don't want the cheapest solution out there but we can't afford to spend too much. Budget could be ~1000-1500€ (before VAT) Robustness: we would like to setup a RAID array and maybe have an external disk where we can store backups Virtualization: we need to be able to setup few servers for development. The scenario is something like this (~8 appliances running in parallel): Redmine + GIT server Bacula server FTP server 3-4 virtual appliances that could be set up on demand to test our applications or support a customer. The appliances could be: LAMP, Tomcat+PostgreSQL, SQL Server Support: if something breaks down it shouldn't be too difficult to find a replacement. Now, given the main requirements, there are some doubts we need to clarify: Do you suggest to buy a prepackaged solution (for example a customized Dell PowerEdge T110 or T310) or to assemble the server by ourselves (buy the separate components)? What RAID configuration do you suggest? I was thinking of RAID1 (probably cheaper) or RAID5. should we buy a hardware RAID controller or is it ok to use a software RAID (mdadm)? In case, which controller do you suggest? What processor do you suggest (Intel Xeon, i3, i5, i7, AMD)? How much RAM? (I was thinking at least 8GB, ~1GB per appliance) What virtualization software do you recommend? VMWare seems to be the best choice, but what about XEN or KVM? We don't want to buy licenses at the moment so we would like to consider only free options. What OS do you recommend? We know Ubuntu, Debian, Gentoo very well (we would like to use Ubuntu Server), however it seems a lot of people goes for CentOS. Thanks in advance if you can help us with this! It's our first "serious" server so many doubts popped up :) Please feel free to add further recommendations if you have some to share ;) Have a nice day

    Read the article

  • How To Switch Back to Outlook 2007 After the 2010 Beta Ends

    - by Matthew Guay
    Are you switching back to Outlook 2007 after trying out Office 2010 beta?  Here’s how you can restore your Outlook data and keep everything working fine after the switch. Whenever you install a newer version of Outlook, it will convert your profile and data files to the latest format.  This makes them work the best in the newer version of Outlook, but may cause problems if you decide to revert to an older version.  If you installed Outlook 2010 beta, it automatically imported and converted your profile from Outlook 2007.  When the beta expires, you will either have to reinstall Office 2007 or purchase a copy of Office 2010. If you choose to reinstall Office 2007, you may notice an error message each time you open Outlook. Outlook will still work fine and all of your data will be saved, but this error message can get annoying.  Here’s how you can create a new profile, import all of your old data, and get rid of this error message. Banish the Error Message with a New Profile To get rid of this error message, we need to create a new Outlook profile.  First, make sure your Outlook data files are backed up.  Your messages, contacts, calendar, and more are stored in a .pst file in your appdata folder.  Enter the following in the address bar of an Explorer window to open your Outlook data folder, and replace username with your user name: C:\Users\username\AppData\Local\Microsoft\Outlook Copy the Outlook Personal Folders (.pst) files that contain your data. Its name is usually your email address, though it may have a different name.  If in doubt, select all of the Outlook Personal Folders files, copy them, and save them in another safe place (such as your Documents folder). Now, let’s remove your old profile.  Open Control Panel, and select Mail.  In Windows Vista or 7, simply enter “Mail” in the search box and select the first entry. Click the “Show Profiles…” button. Now, select your Outlook profile, and click Remove.  This will not delete your data files, but will remove them from Outlook. Press Yes to confirm that you wish to remove this profile. Open Outlook, and you will be asked to create a new profile.  Enter a name for your new profile, and press Ok. Now enter your email account information to setup Outlook as normal. Outlook will attempt to automatically configure your account settings.  This usually works for accounts with popular email systems, but if it fails to find your information you can enter it manually.  Press finish when everything’s done. Outlook will now go ahead and download messages from your email account.  In our test, we used a Gmail account that still had all of our old messages online.  Those files are backed up in our old Outlook data files, so we can save time and not download them.  Click the Send/Receive button on the bottom of the window, and select “Cancel Send/Receive”. Restore Your Old Outlook Data Let’s add our old Outlook file back to Outlook 2007.  Exit Outlook, and then go back to Control Panel, and select Mail as above.  This time, click the Data Files button. Click the Add button on the top left. Select “Office Outlook Personal Folders File (.pst)”, and click Ok. Now, select your old Outlook data file.  It should be in the folder that opens by default; if not, browse to the backup copy we saved earlier, and select it. Press Ok at the next dialog to accept the default settings. Now, select the data file we just imported, and click “Set as Default”. Now, all of your old messages, appointments, contacts, and everything else will be right in Outlook ready for you.  Click Ok, and then open Outlook to see the change. All of the data that was in Outlook 2010 is now ready to use in Outlook 2007.  You won’t have to wait to re-download all of your emails from the server since everything’s still here ready to be used.  And when you open Outlook, you won’t see any error messages, either! Conclusion Migrating your Outlook profile back to Outlook 2007 is fairly easy, and with these steps, you can avoid seeing an error message every time you open Outlook.  With all your data in tact, you’re ready to get back to work instead of getting frustrated with Outlook.  Many of us use webmail and keep all of our messages in the cloud, but even on broadband connections it can take a long time to download several gigabytes of emails. Similar Articles Productive Geek Tips Opening Attachments in Outlook 2007 by KeyboardQuickly Create Appointments from Tasks with Outlook 2007’s To-Do BarFix For Outlook 2007 Constantly Asking for Password on VistaPin Microsoft Outlook to the Desktop BackgroundOur Look at the LinkedIn Social Connector for Outlook TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Download Free MP3s from Amazon Awe inspiring, inter-galactic theme (Win 7) Case Study – How to Optimize Popular Wordpress Sites Restore Hidden Updates in Windows 7 & Vista Iceland an Insurance Job? Find Downloads and Add-ins for Outlook

    Read the article

  • SQL SERVER – 2008 – Introduction to Snapshot Database – Restore From Snapshot

    - by pinaldave
    Snapshot database is one of the most interesting concepts that I have used at some places recently. Here is a quick definition of the subject from Book On Line: A Database Snapshot is a read-only, static view of a database (the source database). Multiple snapshots can exist on a source database and can always reside on the same server instance as the database. Each database snapshot is consistent, in terms of transactions, with the source database as of the moment of the snapshot’s creation. A snapshot persists until it is explicitly dropped by the database owner. If you do not know how Snapshot database work, here is a quick note on the subject. However, please refer to the official description on Book-on-Line for accuracy. Snapshot database is a read-only database created from an original database called the “source database”. This database operates at page level. When Snapshot database is created, it is produced on sparse files; in fact, it does not occupy any space (or occupies very little space) in the Operating System. When any data page is modified in the source database, that data page is copied to Snapshot database, making the sparse file size increases. When an unmodified data page is read in the Snapshot database, it actually reads the pages of the original database. In other words, the changes that happen in the source database are reflected in the Snapshot database. Let us see a simple example of Snapshot. In the following exercise, we will do a few operations. Please note that this script is for demo purposes only- there are a few considerations of CPU, DISK I/O and memory, which will be discussed in the future posts. Create Snapshot Delete Data from Original DB Restore Data from Snapshot First, let us create the first Snapshot database and observe the sparse file details. USE master GO -- Create Regular Database CREATE DATABASE RegularDB GO USE RegularDB GO -- Populate Regular Database with Sample Table CREATE TABLE FirstTable (ID INT, Value VARCHAR(10)) INSERT INTO FirstTable VALUES(1, 'First'); INSERT INTO FirstTable VALUES(2, 'Second'); INSERT INTO FirstTable VALUES(3, 'Third'); GO -- Create Snapshot Database CREATE DATABASE SnapshotDB ON (Name ='RegularDB', FileName='c:\SSDB.ss1') AS SNAPSHOT OF RegularDB; GO -- Select from Regular and Snapshot Database SELECT * FROM RegularDB.dbo.FirstTable; SELECT * FROM SnapshotDB.dbo.FirstTable; GO Now let us see the resultset for the same. Now let us do delete something from the Original DB and check the same details we checked before. -- Delete from Regular Database DELETE FROM RegularDB.dbo.FirstTable; GO -- Select from Regular and Snapshot Database SELECT * FROM RegularDB.dbo.FirstTable; SELECT * FROM SnapshotDB.dbo.FirstTable; GO When we check the details of sparse file created by Snapshot database, we will find some interesting details. The details of Regular DB remain the same. It clearly shows that when we delete data from Regular/Source DB, it copies the data pages to Snapshot database. This is the reason why the size of the snapshot DB is increased. Now let us take this small exercise to  the next level and restore our deleted data from Snapshot DB to Original Source DB. -- Restore Data from Snapshot Database USE master GO RESTORE DATABASE RegularDB FROM DATABASE_SNAPSHOT = 'SnapshotDB'; GO -- Select from Regular and Snapshot Database SELECT * FROM RegularDB.dbo.FirstTable; SELECT * FROM SnapshotDB.dbo.FirstTable; GO -- Clean up DROP DATABASE [SnapshotDB]; DROP DATABASE [RegularDB]; GO Now let us check the details of the select statement and we can see that we are successful able to restore the database from Snapshot Database. We can clearly see that this is a very useful feature in case you would encounter a good business that needs it. I would like to request the readers to suggest more details if they are using this feature in their business. Also, let me know if you think it can be potentially used to achieve any tasks. Complete Script of the afore- mentioned operation for easy reference is as follows: USE master GO -- Create Regular Database CREATE DATABASE RegularDB GO USE RegularDB GO -- Populate Regular Database with Sample Table CREATE TABLE FirstTable (ID INT, Value VARCHAR(10)) INSERT INTO FirstTable VALUES(1, 'First'); INSERT INTO FirstTable VALUES(2, 'Second'); INSERT INTO FirstTable VALUES(3, 'Third'); GO -- Create Snapshot Database CREATE DATABASE SnapshotDB ON (Name ='RegularDB', FileName='c:\SSDB.ss1') AS SNAPSHOT OF RegularDB; GO -- Select from Regular and Snapshot Database SELECT * FROM RegularDB.dbo.FirstTable; SELECT * FROM SnapshotDB.dbo.FirstTable; GO -- Delete from Regular Database DELETE FROM RegularDB.dbo.FirstTable; GO -- Select from Regular and Snapshot Database SELECT * FROM RegularDB.dbo.FirstTable; SELECT * FROM SnapshotDB.dbo.FirstTable; GO -- Restore Data from Snapshot Database USE master GO RESTORE DATABASE RegularDB FROM DATABASE_SNAPSHOT = 'SnapshotDB'; GO -- Select from Regular and Snapshot Database SELECT * FROM RegularDB.dbo.FirstTable; SELECT * FROM SnapshotDB.dbo.FirstTable; GO -- Clean up DROP DATABASE [SnapshotDB]; DROP DATABASE [RegularDB]; GO Reference : Pinal Dave (http://blog.SQLAuthority.com) Filed under: SQL, SQL Authority, SQL Backup and Restore, SQL Data Storage, SQL Query, SQL Server, SQL Tips and Tricks, SQLServer, T SQL, Technology

    Read the article

  • Complete Guide to Networking Windows 7 with XP and Vista

    - by Mysticgeek
    Since there are three versions of Windows out in the field these days, chances are you need to share data between them. Today we show how to get each version to be share files and printers with one another. In a perfect world, getting your computers with different Microsoft operating systems to network would be as easy as clicking a button. With the Windows 7 Homegroup feature, it’s almost that easy. However, getting all three of them to communicate with each other can be a bit of a challenge. Today we’ve put together a guide that will help you share files and printers in whatever scenario of the three versions you might encounter on your home network. Sharing Between Windows 7 and XP The most common scenario you’re probably going to run into is sharing between Windows 7 and XP.  Essentially you’ll want to make sure both machines are part of the same workgroup, set up the correct sharing settings, and making sure network discovery is enabled on Windows 7. The biggest problem you may run into is finding the correct printer drivers for both versions of Windows. Share Files and Printers Between Windows 7 & XP  Map a Network Drive Another method of sharing data between XP and Windows 7 is mapping a network drive. If you don’t need to share a printer and only want to share a drive, then you can just map an XP drive to Windows 7. Although it might sound complicated, the process is not bad. The trickiest part is making sure you add the appropriate local user. This will allow you to share the contents of an XP drive to your Windows 7 computer. Map a Network Drive from XP to Windows 7 Sharing between Vista and Windows 7 Another scenario you might run into is having to share files and printers between a Vista and Windows 7 machine. The process is a bit easier than sharing between XP and Windows 7, but takes a bit of work. The Homegroup feature isn’t compatible with Vista, so we need to go through a few different steps. Depending on what your printer is, sharing it should be easier as Vista and Windows 7 do a much better job of automatically locating the drivers. How to Share Files and Printers Between Windows 7 and Vista Sharing between Vista and XP When Windows Vista came out, hardware requirements were intensive, drivers weren’t ready, and sharing between them was complicated due to the new Vista structure. The sharing process is pretty straight-forward if you’re not using password protection…as you just need to drop what you want to share into the Vista Public folder. On the other hand, sharing with password protection becomes a bit more difficult. Basically you need to add a user and set up sharing on the XP machine. But once again, we have a complete tutorial for that situation. Share Files and Folders Between Vista and XP Machines Sharing Between Windows 7 with Homegroup If you have one or more Windows 7 machine, sharing files and devices becomes extremely easy with the Homegroup feature. It’s as simple as creating a Homegroup on on machine then joining the other to it. It allows you to stream media, control what data is shared, and can also be password protected. If you don’t want to make your Windows 7 machines part of the same Homegroup, you can still share files through the Public Folder, and setup a printer to be shared as well.   Use the Homegroup Feature in Windows 7 to Share Printers and Files Create a Homegroup & Join a New Computer To It Change which Files are Shared in a Homegroup Windows Home Server If you want an ultimate setup that creates a centralized location to share files between all systems on your home network, regardless of the operating system, then set up a Windows Home Server. It allows you to centralize your important documents and digital media files on one box and provides easy access to data and the ability to stream media to other machines on your network. Not only that, but it provides easy backup of all your machines to the server, in case disaster strikes. How to Install and Setup Windows Home Server How to Manage Shared Folders on Windows Home Server Conclusion The biggest annoyance is dealing with printers that have a different set of drivers for each OS. There is no real easy way to solve this problem. Our best advice is to try to connect it to one machine, and if the drivers won’t work, hook it up to the other computer and see if that works. Each printer manufacturer is different, and Windows doesn’t always automatically install the correct drivers for the device. We hope this guide helps you share your data between whichever Microsoft OS scenario you might run into! Here are some other articles that will help you accomplish your home networking needs: Share a Printer on a Home Network from Vista or XP to Windows 7 How to Share a Folder the XP Way in Windows Vista Similar Articles Productive Geek Tips Delete Wrong AutoComplete Entries in Windows Vista MailSvchost Viewer Shows Exactly What Each svchost.exe Instance is DoingFixing "BOOTMGR is missing" Error While Trying to Boot Windows VistaShow Hidden Files and Folders in Windows 7 or VistaAdd Color Coding to Windows 7 Media Center Program Guide TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Icelandic Volcano Webcams Open Multiple Links At One Go NachoFoto Searches Images in Real-time Office 2010 Product Guides Google Maps Place marks – Pizza, Guns or Strip Clubs Monitor Applications With Kiwi

    Read the article

  • Use ASP.NET 4 Browser Definitions with ASP.NET 3.5

    - by Stephen Walther
    We updated the browser definitions files included with ASP.NET 4 to include information on recent browsers and devices such as Google Chrome and the iPhone. You can use these browser definition files with earlier versions of ASP.NET such as ASP.NET 3.5. The updated browser definition files, and instructions for installing them, can be found here: http://aspnet.codeplex.com/releases/view/41420 The changes in the browser definition files can cause backwards compatibility issues when you upgrade an ASP.NET 3.5 web application to ASP.NET 4. If you encounter compatibility issues, you can install the old browser definition files in your ASP.NET 4 application. The old browser definition files are included in the download file referenced above. What’s New in the ASP.NET 4 Browser Definition Files The complete set of browsers supported by the new ASP.NET 4 browser definition files is represented by the following figure:     If you look carefully at the figure, you’ll notice that we added browser definitions for several types of recent browsers such as Internet Explorer 8, Firefox 3.5, Google Chrome, Opera 10, and Safari 4. Furthermore, notice that we now include browser definitions for several of the most popular mobile devices: BlackBerry, IPhone, IPod, and Windows Mobile (IEMobile). The mobile devices appear in the figure with a purple background color. To improve performance, we removed a whole lot of outdated browser definitions for old cell phones and mobile devices. We also cleaned up the information contained in the browser files. Here are some of the browser features that you can detect: Are you a mobile device? <%=Request.Browser.IsMobileDevice %> Are you an IPhone? <%=Request.Browser.MobileDeviceModel == "IPhone" %> What version of JavaScript do you support? <%=Request.Browser["javascriptversion"] %> What layout engine do you use? <%=Request.Browser["layoutEngine"] %>   Here’s what you would get if you displayed the value of these properties using Internet Explorer 8: Here’s what you get when you use Google Chrome: Testing Browser Settings When working with browser definition files, it is useful to have some way to test the capability information returned when you request a page with different browsers. You can use the following method to return the HttpBrowserCapabilities the corresponds to a particular user agent string and set of browser headers: public HttpBrowserCapabilities GetBrowserCapabilities(string userAgent, NameValueCollection headers) { HttpBrowserCapabilities browserCaps = new HttpBrowserCapabilities(); Hashtable hashtable = new Hashtable(180, StringComparer.OrdinalIgnoreCase); hashtable[string.Empty] = userAgent; // The actual method uses client target browserCaps.Capabilities = hashtable; var capsFactory = new System.Web.Configuration.BrowserCapabilitiesFactory(); capsFactory.ConfigureBrowserCapabilities(headers, browserCaps); capsFactory.ConfigureCustomCapabilities(headers, browserCaps); return browserCaps; } At the end of this blog entry, there is a link to download a simple Visual Studio 2008 project – named Browser Definition Test -- that uses this method to display capability information for arbitrary user agent strings. For example, if you enter the user agent string for an iPhone then you get the results in the following figure: The Browser Definition Test application enables you to submit a user-agent string and display a table of browser capabilities information. The browser definition files contain sample user-agent strings for each browser definition. I got the iPhone user-agent string from the comments in the iphone.browser file. Enumerating Browser Definitions Someone asked in the comments whether or not there is a way to enumerate all of the browser definitions. You can do this if you ware willing to use a little reflection and read a private property. The browser definition files in the config\browsers folder get parsed into a class named BrowserCapabilitesFactory. After you run the aspnet_regbrowsers tool, you can see the source for this class in the config\browser folder by opening a file named BrowserCapsFactory.cs. The BrowserCapabilitiesFactoryBase class has a protected property named BrowserElements that represents a Hashtable of all of the browser definitions. Here's how you can read this protected property and display the ID for all of the browser definitions: var propInfo = typeof(BrowserCapabilitiesFactory).GetProperty("BrowserElements", BindingFlags.NonPublic | BindingFlags.Instance); Hashtable browserDefinitions = (Hashtable)propInfo.GetValue(new BrowserCapabilitiesFactory(), null); foreach (var key in browserDefinitions.Keys) { Response.Write("" + key); } If you run this code using Visual Studio 2008 then you get the following results: You get a huge number of outdated browsers and devices. In all, 449 browser definitions are listed. If you run this code using Visual Studio 2010 then you get the following results: In the case of Visual Studio 2010, all the old browsers and devices have been removed and you get only 19 browser definitions. Conclusion The updated browser definition files included in ASP.NET 4 provide more accurate information for recent browsers and devices. If you would like to test the new browser definitions with different user-agent strings then I recommend that you download the Browser Definition Test project: Browser Definition Test Project

    Read the article

  • MEF CompositionInitializer for WPF

    - by Reed
    The Managed Extensibility Framework is an amazingly useful addition to the .NET Framework.  I was very excited to see System.ComponentModel.Composition added to the core framework.  Personally, I feel that MEF is one tool I’ve always been missing in my .NET development. Unfortunately, one perfect scenario for MEF tends to fall short of it’s full potential is in Windows Presentation Foundation development.  In particular, there are many times when the XAML parser constructs objects in WPF development, which makes composition of those parts difficult.  The current release of MEF (Preview Release 9) addresses this for Silverlight developers via System.ComponentModel.Composition.CompositionInitializer.  However, there is no equivalent class for WPF developers. The CompositionInitializer class provides the means for an object to compose itself.  This is very useful with WPF and Silverlight development, since it allows a View, such as a UserControl, to be generated via the standard XAML parser, and still automatically pull in the appropriate ViewModel in an extensible manner.  Glenn Block has demonstrated the usage for Silverlight in detail, but the same issues apply in WPF. As an example, let’s take a look at a very simple case.  Take the following XAML for a Window: <Window x:Class="WpfApplication1.MainView" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" Title="MainWindow" Height="220" Width="300"> <Grid> <TextBlock Text="{Binding TheText}" /> </Grid> </Window> This does nothing but create a Window, add a simple TextBlock control, and use it to display the value of our “TheText” property in our DataContext class.  Since this is our main window, WPF will automatically construct and display this Window, so we need to handle constructing the DataContext and setting it ourselves. We could do this in code or in XAML, but in order to do it directly, we would need to hard code the ViewModel type directly into our XAML code, or we would need to construct the ViewModel class and set it in the code behind.  Both have disadvantages, and the disadvantages grow if we’re using MEF to compose our ViewModel. Ideally, we’d like to be able to have MEF construct our ViewModel for us.  This way, it can provide any construction requirements for our ViewModel via [ImportingConstructor], and it can handle fully composing the imported properties on our ViewModel.  CompositionInitializer allows this to occur. We use CompositionInitializer within our View’s constructor, and use it for self-composition of our View.  Using CompositionInitializer, we can modify our code behind to: public partial class MainView : Window { public MainView() { InitializeComponent(); CompositionInitializer.SatisfyImports(this); } [Import("MainViewModel")] public object ViewModel { get { return this.DataContext; } set { this.DataContext = value; } } } We then can add an Export on our ViewModel class like so: [Export("MainViewModel")] public class MainViewModel { public string TheText { get { return "Hello World!"; } } } MEF will automatically compose our application, decoupling our ViewModel injection to the DataContext of our View until runtime.  When we run this, we’ll see: There are many other approaches for using MEF to wire up the extensible parts within your application, of course.  However, any time an object is going to be constructed by code outside of your control, CompositionInitializer allows us to continue to use MEF to satisfy the import requirements of that object. In order to use this from WPF, I’ve ported the code from MEF Preview 9 and Glenn Block’s (now obsolete) PartInitializer port to Windows Presentation Foundation.  There are some subtle changes from the Silverlight port, mainly to handle running in a desktop application context.  The default behavior of my port is to construct an AggregateCatalog containing a DirectoryCatalog set to the location of the entry assembly of the application.  In addition, if an “Extensions” folder exists under the entry assembly’s directory, a second DirectoryCatalog for that folder will be included.  This behavior can be overridden by specifying a CompositionContainer or one or more ComposablePartCatalogs to the System.ComponentModel.Composition.Hosting.CompositionHost static class prior to the first use of CompositionInitializer. Please download CompositionInitializer and CompositionHost for VS 2010 RC, and contact me with any feedback. Composition.Initialization.Desktop.zip Edit on 3/29: Glenn Block has since updated his version of CompositionInitializer (and ExportFactory<T>!), and made it available here: http://cid-f8b2fd72406fb218.skydrive.live.com/self.aspx/blog/Composition.Initialization.Desktop.zip This is a .NET 3.5 solution, and should soon be pushed to CodePlex, and made available on the main MEF site.

    Read the article

  • Blending the Sketchflow Action

    - by GeekAgilistMercenary
    Started a new Sketchflow Prototype in Expression Blend recently and documented each of the steps.  This blog entry covers some of those steps, which are the basic elements of any prototype.  I will have more information regarding design, prototype creation, and the process of the initial phases for development in the future.  For now, I hope you enjoy this short walk through.  Also, be sure to check out my last quick entry on Sketchflow. I started off with a Sketchflow Project, just like I did in my previous entry (more specifics in that entry about how to manipulate and build out the Sketchflow Map). Once I created the project I setup the following Sketchflow Map. The CoreNavigation is a ComponentScreen setup solely for the page navigation at the top of the screen.  The XAML markup in case you want to create a Component Screen with the same design is included below. <UserControl xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:d="http://schemas.microsoft.com/expression/blend/2008" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" mc:Ignorable="d" xmlns:i="clr-namespace:System.Windows.Interactivity;assembly=System.Windows.Interactivity" xmlns:pb="clr-namespace:Microsoft.Expression.Prototyping.Behavior;assembly=Microsoft.Expression.Prototyping.Interactivity" x:Class="RapidPrototypeSketchScreens.CoreNavigation" d:DesignWidth="624" d:DesignHeight="49" Height="49" Width="624">   <Grid x:Name="LayoutRoot"> <TextBlock HorizontalAlignment="Stretch" Margin="307,3,0,0" Style="{StaticResource TitleCenter-Sketch}" Text="Aütøchart Scorecards" TextWrapping="Wrap"> <i:Interaction.Triggers> <i:EventTrigger EventName="MouseLeftButtonDown"> <pb:NavigateToScreenAction TargetScreen="RapidPrototypeSketchScreens.Screen_1"/> </i:EventTrigger> </i:Interaction.Triggers> </TextBlock> <Button HorizontalAlignment="Left" Margin="164,8,0,11" Style="{StaticResource Button-Sketch}" Width="144" Content="Scorecard"> <i:Interaction.Triggers> <i:EventTrigger EventName="Click"> <pb:NavigateToScreenAction TargetScreen="RapidPrototypeSketchScreens.Screen_1_2"/> </i:EventTrigger> </i:Interaction.Triggers> </Button> <Button HorizontalAlignment="Left" Margin="8,8,0,11" Style="{StaticResource Button-Sketch}" Width="152" Content="Standard Reports"> <i:Interaction.Triggers> <i:EventTrigger EventName="Click"> <pb:NavigateToScreenAction TargetScreen="RapidPrototypeSketchScreens.Screen_1_1"/> </i:EventTrigger> </i:Interaction.Triggers> </Button> </Grid> </UserControl> Now that the CoreNavigation Component Screen is done I built out each of the others.  In each of those screens I included the CoreNavigation Screen (all those little green lines in the image) as the top navigation.  In order to do that, as I created each of the pages I would hover over the CoreNavigation Object in the Sketchflow Map.  When the utilities drawer (the small menu that pops down under a node when you hover over it) shows click on the third little icon and drag it onto the page node you want a navigation screen on. Once I created all the screens I setup the navigation by opening up each screen and right clicking on the objects that needed to point to somewhere else in the prototype. Once I was done with the main page, my Home Navigation Page, it looked something like this in the Expression Blend Designer. I fleshed out each of the additional screens.  Once I was done I wanted to try out the deployment package.  The way to deploy a Sketchflow Prototype is to merely click on File –> Package SketchFlow Project and a prompt will appear.  In the prompt enter what you want the package to be called. I like to see the files generated afterwards too, so I checked the box to see that.  When Expression Blend is done generating everything you’ll have a directory like the one shown below, with all the needed files for deployment. Now these files can be copied or moved to any location for viewing.  One can even copy them (such as via FTP) to a server location to share with others.  Once they are deployed and you run the "TestPage.html" the other features of the Sketchflow Package are available. In the image below I have tagged a few sections to show the Sketchflow Player Features.  To the top left is the navigation, which provides a clearly defined area of movement in a list.  To the center right is the actual prototype application.  I have placed lists of things and made edits.  On the left hand side is the highlight feature, which is available in the Feedback section of the lower left.  On the right hand list I underlined the Autochart with an orange marker, and marked out two list items with a red marker. In the lower left hand side in the Feedback section is also an area to type in your feedback.  This can be useful for time based feedback, when you post this somewhere and want people to provide subsequent follow up feedback. Overall lots of great features, that enable some fairly rapid prototyping with customers.  Once one is familiar with the steps and parts of this Sketchflow Prototype Capabilities it is easy to step through an application without even stopping.  It really is that easy.  So get hold of Expression Blend 3 and get ramped up on Sketchflow, it will pay off in the design phases to do so! Original Entry

    Read the article

  • How to Animate Text and Objects in PowerPoint 2010

    - by DigitalGeekery
    Are you looking for an eye catching way to keep your audience interested in your PowerPoint presentations? Today we’ll take a look at how to add animation effects to objects in PowerPoint 2010. Select the object you wish to animate and then click the More button in the Animation group of the Animation tab.   Animations are grouped into four categories. Entrance effects, Exit effects, Emphasis effects, and Motion Paths. You can get a Live Preview of how the animation will look by hovering your mouse over an animation effect.   When you select a Motion Path, your object will move along the dashed path line as shown on the screen. (This path is not displayed in the final output) Certain aspects of the Motion Path effects are editable. When you apply a Motion Path animation to an object, you can select the path and drag the end to change the length or size of the path. The green marker along the motion path marks the beginning of the  path and the red marks the end. The effects can be rotated by clicking and the bar near the center of the effect.   You can display additional effects by choosing one of the options at the bottom. This will pop up a Change Effect window. If you have Preview Effect checked at the lower left you can preview the effects by single clicking.   Apply Multiple Animations to an Object Select the object and then click the Add Animation button to display the animation effects. Just as we did with the first effect, you can hover over to get a live preview. Click to apply the effect. The animation effects will happen in the order they are applied. Animation Pane You can view a list of the animations applied to a slide by opening the Animation Pane. Select the Animation Pane button from the Advanced Animation group to display the Animation Pane on the right. You’ll see that each animation effect in the animation pane has an assigned number to the left.    Timing Animation Effects You can change when your animation starts to play. By default it is On Click. To change it, select the effect in the Animation Pane and then choose one of the options from the Start dropdown list. With Previous starts at the same time as the previous animation and After Previous starts after the last animation. You can also edit the duration that the animations plays and also set a delay.   You can change the order in which the animation effects are applied by selecting the effect in the animation pane and clicking Move Earlier or Move Later from the Timing group on the Animation tab. Effect Options If the Effect Options button is available when your animation is selected, then that particular animation has some additional effect settings that can be configured. You can access the Effect Option by right-clicking on the the animation in the Animation Pane, or by selecting Effect Options on the ribbon.   The available options will vary by effect and not all animation effects will have Effect Options settings. In the example below, you can change the amount of spinning and whether the object will spin clockwise or counterclockwise.   Under Enhancements, you can add sound effects to your animation. When you’re finished click OK.   Animating Text Animating Text works the same as animating an object. Simply select your text box and choose an animation. Text does have some different Effect Options. By selecting a sequence, you decide whether the text appears as one object, all at once, or by paragraph. As is the case with objects, there will be different available Effect Options depending on the animation you choose. Some animations, such as the Fly In animation, will have directional options.   Testing Your Animations Click on the Preview button at any time to test how your animations look. You can also select the Play button on the Animation Pane. Conclusion Animation effects are a great way to focus audience attention on important points and hold viewers interest in your PowerPoint presentations. Another cool way to spice up your PPT 2010 presentations is to add video from the web. What tips do you guys have for making your PowerPoint presentations more interesting? Similar Articles Productive Geek Tips Center Pictures and Other Objects in Office 2007 & 2010Preview Before You Paste with Live Preview in Office 2010Embed True Type Fonts in Word and PowerPoint 2007 DocumentsHow to Add Video from the Web in PowerPoint 2010Add Artistic Effects to Your Pictures in Office 2010 TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 24 Million Sites Windows Media Player Glass Icons (icons we like) How to Forecast Weather, without Gadgets Outlook Tools, one stop tweaking for any Outlook version Zoofs, find the most popular tweeted YouTube videos Video preview of new Windows Live Essentials

    Read the article

  • How to Assign a Static IP Address in XP, Vista, or Windows 7

    - by Mysticgeek
    When organizing your home network it’s easier to assign each computer it’s own IP address than using DHCP. Here we will take a look at doing it in XP, Vista, and Windows 7. If you have a home network with several computes and devices, it’s a good idea to assign each of them a specific address. If you use DHCP (Dynamic Host Configuration Protocol), each computer will request and be assigned an address every time it’s booted up. When you have to do troubleshooting on your network, it’s annoying going to each machine to figure out what IP they have. Using Static IPs prevents address conflicts between devices and allows you to manage them more easily. Assigning IPs to Windows is essentially the same process, but getting to where you need to be varies between each version. Windows 7 To change the computer’s IP address in Windows 7, type network and sharing into the Search box in the Start Menu and select Network and Sharing Center when it comes up.   Then when the Network and Sharing Center opens, click on Change adapter settings. Right-click on your local adapter and select Properties. In the Local Area Connection Properties window highlight Internet Protocol Version 4 (TCP/IPv4) then click the Properties button. Now select the radio button Use the following IP address and enter in the correct IP, Subnet mask, and Default gateway that corresponds with your network setup. Then enter your Preferred and Alternate DNS server addresses. Here we’re on a home network and using a simple Class C network configuration and Google DNS. Check Validate settings upon exit so Windows can find any problems with the addresses you entered. When you’re finished click OK. Now close out of the Local Area Connections Properties window. Windows 7 will run network diagnostics and verify the connection is good. Here we had no problems with it, but if you did, you could run the network troubleshooting wizard. Now you can open the command prompt and do an ipconfig  to see the network adapter settings have been successfully changed.   Windows Vista Changing your IP from DHCP to a Static address in Vista is similar to Windows 7, but getting to the correct location is a bit different. Open the Start Menu, right-click on Network, and select Properties. The Network and Sharing Center opens…click on Manage network connections. Right-click on the network adapter you want to assign an IP address and click Properties. Highlight Internet Protocol Version 4 (TCP/IPv4) then click the Properties button. Now change the IP, Subnet mask, Default Gateway, and DNS Server Addresses. When you’re finished click OK. You’ll need to close out of Local Area Connection Properties for the settings to go into effect. Open the Command Prompt and do an ipconfig to verify the changes were successful.   Windows XP In this example we’re using XP SP3 Media Center Edition and changing the IP address of the Wireless adapter. To set a Static IP in XP right-click on My Network Places and select Properties. Right-click on the adapter you want to set the IP for and select Properties. Highlight Internet Protocol (TCP/IP) and click the Properties button. Now change the IP, Subnet mask, Default Gateway, and DNS Server Addresses. When you’re finished click OK. You will need to close out of the Network Connection Properties screen before the changes go into effect.   Again you can verify the settings by doing an ipconfig in the command prompt. In case you’re not sure how to do this, click on Start then Run.   In the Run box type in cmd and click OK. Then at the prompt type in ipconfig and hit Enter. This will show the IP address for the network adapter you changed.   If you have a small office or home network, assigning each computer a specific IP address makes it a lot easier to manage and troubleshoot network connection problems. Similar Articles Productive Geek Tips Change Ubuntu Desktop from DHCP to a Static IP AddressChange Ubuntu Server from DHCP to a Static IP AddressVista Breadcrumbs for Windows XPCreate a Shortcut or Hotkey for the Safely Remove Hardware DialogCreate a Shortcut or Hotkey to Eject the CD/DVD Drive TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Nice Websites To Watch TV Shows Online 24 Million Sites Windows Media Player Glass Icons (icons we like) How to Forecast Weather, without Gadgets Outlook Tools, one stop tweaking for any Outlook version Zoofs, find the most popular tweeted YouTube videos

    Read the article

< Previous Page | 827 828 829 830 831 832 833 834 835 836 837 838  | Next Page >