Search Results

Search found 25551 results on 1023 pages for 'linux validated rpm oracl'.

Page 84/1023 | < Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >

• Autodetect/mount SDCards and run script for them on Linux

  - by Brendan

  Hey Everyone, I'm currently running SME Server, and need to have a script run upon the attachment of SD Cards to my server. The script itself works fine (it copies the contents of the cards), but the automounting and execution of the script is where I'm having issues. The I have a USB hub consisting of 10 USB ports; that shows up as: [root@server ~]# lsusb Bus 004 Device 002: ID 0000:0000 Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 001 Device 055: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 051: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 050: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 001: ID 0000:0000 (The hub is the TERMINUS TECHNOLOGY INC entries) As I cannot plug SD Cards directly into the server; I use a USB to SD card attachement (10 of them) plugged into the hub to read the cards. Upon pluggig the 10 attachments (without cards) into the hub; lsusb yields the following: [root@server ~]# lsusb Bus 004 Device 002: ID 0000:0000 Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 001 Device 073: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 072: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 071: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 070: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 069: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 068: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 067: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 066: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 065: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 064: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 055: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 051: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 050: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 001: ID 0000:0000 As you can see, the readers are the "Gensys Logic, Inc" entries. Plugging in an SD card to a reader doesn't affect lsusb (it reads exactly as above), however my system recognises the cards fine; as indicated by dmesg: Attached scsi generic sg11 at scsi54, channel 0, id 0, lun 0, type 0 USB Mass Storage device found at 73 SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through sdd: sdd1 SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through sdd: sdd1 SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through sdd: sdd1 If I manually mount sdd1 (mount /dev/sdd1 /somedirectory/) this works fine. What I'm really after is a solution that automounts each of the cards as they are inputted into the reader; and executes a script for them (this will involve copying their contents to another directory). My problem is that I don't know how to do this; I don't think udev will work as the USB devices don't change; if I could somehow get udev working with /dev/disk/by-path/ however I think this is doable (it seems to keep constant entries). ls /dev/disk returns: pci-0000:00:1d.7-usb-0:4.1.1.1:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.1.2:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.1.3:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.1.4:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.2:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.3:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.4:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.2:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.3:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.4:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.4:1.0-scsi-0:0:0:0-part1 pci-0000:0b:01.0-scsi-0:0:1:0 pci-0000:0b:01.0-scsi-0:0:1:0-part1 pci-0000:0b:01.0-scsi-0:0:1:0-part2 From above, we can see I have only one card plugged into the reader (pci-0000:00:1d.7-usb-0:4.4:1.0-scsi-0:0:0:0-part1). Going mount /dev/disk/by-path/pci-0000\:00\:1d.7-usb-0\:4.4\:1.0-scsi-0\:0\:0\:0-part1 Works and places the card under /media/usbdisk/, however: mount /dev/disk/by-path/pci-0000\:00\:1d.7-usb-0\:4.4\:1.0-scsi-0\:0\:0\:0-part1 slot1/ doesn't work, and returns "mount: can't get address for /dev/disk/by-path/pci-0000" Any ideas and solutions would be great, I've seen the knowledge of a lot of the guys on here before so I'm hopeful someone can help me out. Thanks

  Read the article

• What are some "must have" Ubuntu/Linux programs?

  - by wag2639

  Inspired by link text, what are some programs thats must have for a developer, general desktop user, etc?

  Read the article

• Recover backup copy of a ubuntu linux installation on a usb stick using dd

  - by user10826

  Hi, I installed Ubuntu 10.04 on a usb stick in persistent install mode. So I could boot the laptop or my desktop computer with the stick, at boot time. Once I needed the 8GB stick for another purposes so I thought about coyping it to my desktop doing from mac os x: dd if=/dev/disks3s of=/Users/jack/Desktop/usb_copy Now I am trying to do the opposite, after having used the stick, which was formatted to NTFS, just doing dd if=/Users/jack/Desktop/usb_copy of=/dev/disks3s but although I can see that almost of the files are there, I can not boot again. IT is also strange the the file permissions are kind of strange, something like _user What can I do ? Thanks

  Read the article

• Linux 'compose' key sequence extensions

  - by o_O Tync

  Compose key is a great way way to write all these ©–®—… stuff. It's really MUCH more handy than the windows "alt+0169" method. Is there a way to define additional sequences? E.g. I'd like to have "Compose+--" result in "?"

  Read the article

• Does Moonlight work on linux in Google Chrome?

  - by Matthew

  I'm trying to install Moonlight, but I can only find instructions for setting it up in Firefox. And in the Ubuntu 10.04 repositories, I found a "moonlight-plugin-mozilla" package, but not "moonlight-plugin-chrome" (or similar). Is there any way to do this, or does Moonlight not yet run in Chrome?

  Read the article

• What's the best self-tracking software for Linux?

  - by trench

  I'm looking for a way to track myself and receive quality data upon which I can write future scripts/programs. For example, I use Google Reader a lot. I'd like to track the hrefs that garner my clicks. Further, I'd like to drop all of the words of each href into a database where they can be stacked in a hierarchical manner. At the end of the week I want to know that "Ubuntu" garnered 448 clicks and "Cheetos" garnered 2. :) That's just one example... I'd like this tracking and data-collecting to extend beyond my browser. I know writing something to do this myself wouldn't be too awfully difficult but if something already exists I'd happily use it. Thanks in advance. Primary OS: Ubuntu 10.04

  Read the article

• Linux WD30EZRX WD Green HDD & Blacx Duet 5G Usb

  - by Adam

  I have connected up an WD30EZRX WD Green HDD to a Thermaltake Blacx Duet 5G USB dock in Ubuntu 12.04. Every thing seems fine except when the HDD idles it seems to have error ls: reading directory .: Input/output error after a while and is only fixed by unmounting and remounting the drive as root. I have the following line in /etc/fstab UUID=AAF670E9F670B6E3 /media/3TB ntfs defaults,user,auto 0 0 I have noticed that it seems to go between /dev/sdc2 and /dev/sdd2 devices on remount. I did copy 1TB last night without issue in 1 sitting. But after x mins of idle it has remount issue. Any tips/suggestions on how to proceed would be appreciated. Spent most of the night googling and all its done is made me sad. Edit (tried as suggested): root@mediaserver:/media/3TB# sudo hdparm -B 255 -S 253 /dev/sdd2 /dev/sdd2: setting Advanced Power Management level to disabled HDIO_DRIVE_CMD failed: Input/output error setting standby to 253 (vendor-specific) APM_level = not supported Seems as if that didn't help with this particular drive.

  Read the article

• How can I diff two Redhat Linux servers?

  - by Stuart Woodward

  I have two servers that have should have the same setup except for known differences. By running: find / \( -path /proc -o -path /sys -o -path /dev \) -prune -o -print | sort > allfiles.txt I can find a list of all the files on one server and compare it against the list of files on the the other server. This will show me the differences in the names of the files that reside on the servers. What I really want to do is run a checksum on all the files on both of the servers and compare them to also find where the contents are different. e.g find / \( -path /proc -o -path /sys -o -path /dev \) -prune -o -print | xargs /usr/bin/sha1sum Is this a sensible way to do this? I was thinking that rysnc already has most of this functionality but can it be used to provide the list of differences?

  Read the article

• Font configuration on Linux dual-head configuration with DPI's at 90 and 150:

  - by Jason Tholstrup

  I have a laptop with a 15" screen and a resolution of 1920 X 1200 and a 22" external monitor running at 1680 X 1050. This means the laptop runs with a dpi of 150 and the monitor runs at a dpi of 90. Is there anyway to get the fonts on the laptop to be readable while keeping the fonts on the monitor from being gigantic?

  Read the article

• How to use WPA2 client mode in the Linux-based Cisco WAP4410N access point

  - by joechip

  I have a Cisco WAP4410N access point that I want to use as a client to connect to a WPA2 wireless network (for WLAN service monitoring purposes). Supposedly this access point supports a "Wireless Client/Repeater" mode that allows to do this. The Repeater function is optional (I have that box unchecked so that nobody can connect to this access point wirelessly). I have verified through SSH that the access point gets configured as a client and not as a Master. But it never associates to the SSID I ask it to. This is what iwconfig shows: ath04 IEEE 802.11ng ESSID:"myownssid" Mode:Managed Channel:0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:14 dBm Sensitivity=1/3 Retry:off RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/94 Signal level=161/162 Noise level=161/161 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Although I've never done this from the command line, I suppose I could use wpa_supplicant or wpa_client to associate it, but I don't know how to do that without editing configuration files and the filesystem is readonly. Besides, I would have to run those commands manually after every reboot. I'd like to know how to do this the Cisco way, if possible. If not, any trick to make this work would be useful. Edit: This is with the latest firmware, 2.0.4.2. And I found that not all of the filesystem is readonly, since /var and /tmp are mounted with type ramfs.

  Read the article

• Linux route add between static LAN and Wifi Gateway

  - by Hamza

  I have two local machines connected to each other via wired ethernet and one of those machines is also connected to a wifi network which provides internet access. A pseudo-graphical representation of the topology is as follows: (PC2)----------(PC1)---------(Wifi Gateway) 192.168.2.x 10.0.0.x The configuration on PC2 is: iface eth0 inet static address 192.168.2.2 network 192.168.2.0 netmask 255.255.255.0 gateway 192.168.2.1 ...and the configuration on PC1 is: iface eth0 inet static address 192.168.2.1 network 192.168.2.0 netmask 255.255.255.0 gateway 192.168.2.1 On PC1, I've added a default route for wlan0 as I couldn't access the internet otherwise: route add default gw 10.0.0.1 wlan0 And also tried setting the gateway for the 192.168.2.x network using: route add -net 192.168.2.0 netmask 255.255.255.0 gw 10.0.0.1 But I still can't access internet from PC2. Edit I don't have access to the wifi gateway.

  Read the article

• How to rename a file by replacing specific letters in the file in linux

  - by Emmanuel

  I used a script that renamed my file eg 'echo webutil.olb | tr [A-Z] [a-z]' i wanted to rename it back to webutil.olb. How do i do this for many other files that i have

  Read the article

• NVRAM for journals on Linux?

  - by symcbean

  I've been thinking about ways of speeding up disk I/O, and one of the bottlenecks I keep coming back to is the journal. There's an obvious benefit to using an SSD for the journal - over and above just write caching unless of course I just disable the journal with the write cache (after all devicemapper doesn't seem to support barriers). In order to get the benefits from using a BB write cache on the controller, then I'd need to disable journalling - but then the OS should try to fsck the system after an outage. Of course if the OS knows what's in the batter-backed memory then it could use it as the journal - but that means it must be exposed as a block device and only be under the control of the operating system. However I've not been able to find a suitable low-cost device (no, write-levelling for Flash is not adequate for a journal, at least one which uses Smartmedia). While there's no end of flash devices, disk/array controllers with BB write caches, so far I've not found anything which just gives me non-volatile memory addressable as a block storage device.

  Read the article

• Unable to mount device on Linux (XFS)

  - by gunnx

  I am unable to mount a device on my server due to error when mounting, the device is type XFS. The mount command returns message: "mount: structure needs cleaning" I've tried using xfs_check and it just returns a message saying that there are entries in the log that need relaying and that you need to run xfs_repair -L where "-L" option deletes the log file but might/will result in data loss/corruption. Does anyone know if you can access/mount the drive without repairing, or anyway to minimise data loss?

  Read the article

• Any beat detection software for Linux?

  - by o_O Tync

  Amarok 2 can search through music collection using ID3v2 tag's 'bpm' field. That would be very nice to retag the entire music collection so I can find the 'mood' of the track I like. However I've not found any beat-detection software that could have helped me. Have you ever used one? CLI, preferably. Also I'm interested if there's anything alike for tagging FLACs with the same 'bpm' field. Thanks! :) P.S. I'm aware there's a nice moodbar feature, however it's useless for searching.

  Read the article

• hard drive forensics tool for linux

  - by Jack

  I am looking for an application I used in 2001. It was a curses application that displayed devices or files in hexadecimal format, and allowed searching through them and other functionality. I can't find anything remotely like this, does anyone have an idea?

  Read the article

• Correct way of bringing network interface down in linux

  - by Karolis T.

  For example: $ ifconfig dummy0 up $ ifconfig dummy0 "192.168.1.190 netmask 255.255.255.0" Calling ifconfig with no parameters shows the interface dummy0 Link encap:Ethernet HWaddr b6:1f:f3:92:6d:20 inet addr:192.168.1.190 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::b41f:f3ff:fe92:6d20/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:1050 (1.0 KiB) How can I bring the interface down so that it doesn't show up in ifconfig ifconfig -a ifconfig dummy0 without rmmod dummy because dummy is used just for example purposes. If there is no way to do that, what "throw-away" IP could I set to it and be safe from any trouble? like $ ifconfig dummy0 down $ ifconfig dummy0 0.0.0.0

  Read the article

• IP-dependent local port-forwarding on Linux

  - by chronos

  I have configured my server's sshd to listen on a non-standard port 42. However, at work I am behind a firewall/proxy, which only allow outgoing connections to ports 21, 22, 80 and 443. Consequently, I cannot ssh to my server from work, which is bad. I do not want to return sshd to port 22. The idea is this: on my server, locally forward port 22 to port 42 if source IP is matching the external IP of my work's network. For clarity, let us assume that my server's IP is 169.1.1.1 (on eth1), and my work external IP is 169.250.250.250. For all IPs different from 169.250.250.250, my server should respond with an expected 'connection refused', as it does for a non-listening port. I'm very new to iptables. I have briefly looked through the long iptables manual and these related / relevant questions: http://serverfault.com/questions/57872/iptables-question-forwarding-port-x-to-an-ssh-port-of-different-machine-on-the-n http://serverfault.com/questions/140622/how-can-i-port-forward-with-iptables However, those questions deal with more complicated several-host scenarios, and it is not clear to me which tables and chains I should use for local port-forwarding, and if I should have 2 rules (for "question" and "answer" packets), or only 1 rule for "question" packets. So far I have only enabled forwarding via sysctl. I will start testing solutions tomorrow, and will appreciate pointers or maybe case-specific examples for implementing my simple scenario. Is the draft solution below correct? iptables -A INPUT [-m state] [-i eth1] --source 169.250.250.250 -p tcp --destination 169.1.1.1:42 --dport 22 --state NEW,ESTABLISHED,RELATED -j ACCEPT Should I use the mangle table instead of filter? And/or FORWARD chain instead of INPUT?

  Read the article

• Linux: Setting primary display (nvidia) form command line

  - by Joernsn

  Is this possible? Normally I use disper to enable my external monitor, but I don't think I can force the 2nd monitor to be primary. http://willem.engen.nl/projects/disper/ I've played around with nv-control-dpy included in the nvidia-control source, but I haven't figured out how to do it yet. How to get: http://ubuntuforums.org/showthread.php?t=922956

  Read the article

• Problem in listening to multicast in multihomed Linux server

  - by Lior

  I am trying to write a multicast client on a machine with two NICs, and I can't make it work. I can see with a sniffer that once I start the program the NIC (eth4) start receiving the multicast datagrams: y.y.y.y. (some ip) - z.z.z.z (multicast ip, not my eth4 NIC IP) UDP Source port: kkk (some other port) Destination port: xxx (multicast port) However, I can't get those packets using my program (listening to port xxx on eth4). I also added: route add 224.0.0.0 netmask 240.0.0.0 dev eth4 Searched the web for some examples/explanations, but it seems like I do what everybody else does. Any help will be appreciated. is there anything else to do with route/iptables?

  Read the article

• /etc/security/limits.conf for setting program limits in Linux

  - by Flavius Akerele

  I have the following inside /etc/security/limits.conf (I have specified root separately because * will not include it.) user2 - core unlimited * - core 0 root - core 0 * - rss 512000 root - rss 512000 * - nproc 100 root - nproc 100 * - maxlogins 1 root - maxlogins 1 I run a program as user2 (./programname) but /proc/3498/limits says cores are disabled: Limit Soft Limit Hard Limit Units Max cpu time unlimited unlimited seconds Max file size unlimited unlimited bytes Max data size unlimited unlimited bytes Max stack size 8388608 unlimited bytes Max core file size 0 0 bytes Max resident set 524288000 524288000 bytes Max processes 100 100 processes Max open files 1024 1024 files Max locked memory 65536 65536 bytes Max address space unlimited unlimited bytes Max file locks unlimited unlimited locks Max pending signals 14001 14001 signals Max msgqueue size 819200 819200 bytes Max nice priority 0 0 Max realtime priority 0 0 Max realtime timeout unlimited unlimited us Both ulimit -Sa and ulimit -Ha output that cores are disabled: core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 14001 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) 512000 open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) unlimited cpu time (seconds, -t) unlimited max user processes (-u) 100 virtual memory (kbytes, -v) unlimited file locks (-x) unlimited Why are cores disabled ?

  Read the article

• Unexplained cache RAM drops on Linux machine

  - by FunkyChicken

  I run a CentOS 5.7 64 machine with 24gb ram and running kernel 2.6.18-274.12.1.el5. This machine runs only Nginx, php-fpm and Xcache as extra applications. Since about 3 weeks my memory behavior on this machine has changed and I cannot explain why. There are no crons running which flush anything like this. There are also no large numbers of files being deleted/changed during these drops. The 'cached' memory gets dropped about every few hours, but it's never a set gap between flushes, this indicates to me that some bottleneck gets reached instead. It also always seems to be when total memory usages gets to about 18GB, but again, not always exactly 18GB. This is a graph of my memory usage: As you can see in the graph the 'buffers' always stay more or less the same, it is mainly the 'cache' that gets dropped. Running vmstat -m I have outputted the memory usage just before and just after a memory drop. The output is here: http://pastebin.com/diff.php?i=hJqZqztm 'old version' being before, 'new version' being after a drop. About 3 weeks ago my server crashed during a heavy DDOS attack, after I rebooted the machine this odd behavior started. I have checked a bunch of logs, restarted the machine again, and cannot find any indication what changed. During these 'cache' memory drops, my iNode usage drops at the same time. Does anyone have any idea what might be causing this behavior? Clearly my RAM isn't full, so I am curious why this could be happening.

  Read the article

• How do I compare binary files in Linux?

  - by frustratedCmpNoLongerUser

  I need to compare two binary files and get the output in the form <fileoffset-hex <file1-byte-hex <file2-byte-hex for every different byte. So if file1.bin is 00 90 00 11 in binary form and file2.bin is 00 91 00 10 I want to get something like 00000001 90 91 00000003 11 10 What is the easiest way to accomplish the goal? Standard tool? Some third-party tool? (Note: cmp -l should be killed with fire, it uses a decimal system for offsets and octal for bytes.)

  Read the article

• Security issue on Linux with Netbeans

  - by WebDevHobo

  In order to edit some files in Netbeans, I had to do a chmod 777 on the parent-folder. Reason being that anything else would result in Netbeans not wanting to accept the folder, as it could not be written. Is there an other way to do this besides doing a chmod 777? I'm on Ubuntu 9.10, using Netbeans 6.7.1 And after that, I manually have to give each file the needed rights. There should be an easier way, I just don't know it. EDIT: I am running XAMPP and the files I'm trying to edit are in the htdocs folder. I'm running Netbeans as my local user account, which is how it starts if I have it run from the applications-menu.

  Read the article

• SSH into Ubuntu Linux on a box without a static IP address

  - by Steven Xu

  Basically, how do I do it? I'd like to connect to my home computer from work, but my internet is routed through my apartment building's network, so I don't have the static IP address I'm accustomed to having. How do I go about accessing my home computer through SSH (I'll be using Putty at work if it matters) if my home computer doesn't have a static IP address?

  Read the article

< Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >