Search Results

Search found 4296 results on 172 pages for 'serial ports'.

Page 85/172 | < Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >

• Un-failing over a Cisco PIX 515e

  - by ABrown

  We had a power outage at our data center last week and when our dual PIX 515E running IOS 7.0(8) (configured with a failover cable) came back, they were in a failed over state where the Secondary unit is active and the Primary unit is standby I have tried 'failover reset', 'failover active', and 'failover reload-standby' as well as executing reloads on both units in a variety of orders, and they don't come back Primary/Active Secondary/Standby. The only thing in my arsenal that I haven't tried is driving to the data center and performing a hard reboot, which I hate to do. I have read How Failover Works on the Cisco Secure Firewall and it seems like this should be wicked straight forward. output of show failover on Primary: Failover On Cable status: Normal Failover unit Primary Failover LAN Interface: N/A - Serial-based failover enabled Unit Poll frequency 15 seconds, holdtime 45 seconds Interface Poll frequency 15 seconds Interface Policy 1 Monitored Interfaces 2 of 250 maximum Version: Ours 7.0(8), Mate 7.0(8) Last Failover at: 02:52:05 UTC Mar 10 2010 This host: Primary - Standby Ready Active time: 0 (sec) Interface outside (x.x.x.165): Normal Interface inside (y.y.y.3): Normal Other host: Secondary - Active Active time: 897045 (sec) Interface outside (x.x.x.164): Normal Interface inside (y.y.y.4): Normal Stateful Failover Logical Update Statistics Link : Unconfigured. output of show failover on Secondary: Failover On Cable status: Normal Failover unit Secondary Failover LAN Interface: N/A - Serial-based failover enabled Unit Poll frequency 15 seconds, holdtime 45 seconds Interface Poll frequency 15 seconds Interface Policy 1 Monitored Interfaces 2 of 250 maximum Version: Ours 7.0(8), Mate 7.0(8) Last Failover at: 02:03:04 UTC Feb 28 2010 This host: Secondary - Active Active time: 896925 (sec) Interface outside (x.x.x.164): Normal Interface inside (y.y.y.4): Normal Other host: Primary - Standby Ready Active time: 0 (sec) Interface outside (x.x.x.165): Normal Interface inside (y.y.y.3): Normal Stateful Failover Logical Update Statistics Link : Unconfigured. I'm seeing the following in my syslog: Mar 10 03:05:00 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reset' command. Mar 10 03:05:09 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reload-standby' command. Mar 10 03:05:12 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=20,my=Active,peer=Failed. Mar 10 03:05:12 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Failed. Mar 10 03:06:09 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=0,my=Active,peer=Failed. Mar 10 03:06:09 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is down. Mar 10 03:06:09 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=1,my=Active,peer=Failed. Mar 10 03:06:10 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is up. Mar 10 03:06:10 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=411,op=2,my=Active,peer=Failed. Mar 10 03:06:23 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=80,my=Active,peer=Standby Ready. Mar 10 03:06:23 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Standby Ready. Mar 10 03:06:24 fw2 %PIX-6-720027: (VPN-Primary) HA status callback: My state Standby Ready. Mar 10 03:07:05 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reset' command. Mar 10 03:07:31 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover active' command. Mar 10 03:08:04 fw1 %PIX-5-611103: User logged out: Uname: enable_1 Mar 10 03:08:04 fw1 %PIX-6-315011: SSH session from admin1_int on interface inside for user "pix" terminated normally Mar 10 03:08:39 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=20,my=Active,peer=Failed. Mar 10 03:08:39 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Failed. Mar 10 03:09:10 fw1 %PIX-6-605005: Login permitted from admin1_int/36891 to inside:192.168.4.4/ssh for user "pix" Mar 10 03:09:23 fw1 %PIX-5-111008: User 'enable_15' executed the 'failover reset' command. Mar 10 03:09:38 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=0,my=Active,peer=Failed. Mar 10 03:09:39 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is down. Mar 10 03:09:39 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=401,op=1,my=Active,peer=Failed. Mar 10 03:09:39 fw1 %PIX-6-720024: (VPN-Secondary) HA status callback: Control channel is up. Mar 10 03:09:39 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=411,op=2,my=Active,peer=Failed. Mar 10 03:09:52 fw1 %PIX-6-720032: (VPN-Secondary) HA status callback: id=3,seq=200,grp=0,event=406,op=80,my=Active,peer=Standby Ready. Mar 10 03:09:52 fw1 %PIX-6-720028: (VPN-Secondary) HA status callback: Peer state Standby Ready. Mar 10 03:09:53 fw2 %PIX-6-720027: (VPN-Primary) HA status callback: My state Standby Ready. I'm not exactly sure how to interpret that syslog data. Primary doesn't seem to even try to become Active. When I reload the individual units separately, my connections are retained, so it doesn't seem like I have a real hardware failure. Is there something I can query (IOS or SNMP) to check for hardware issues? Any thoughts? My IOS-fu is weak. Thanks for any help you might provide, Aaron

  Read the article

• kernel panic with exitcode=0x00000004 and no call trace

  - by litmusconfig

  A bit of background first - I'm trying to configure a MicroBlaze Linux (big-endian version) system on a Xilinx ML506 eval board. The goal is to use the second partition of a CompactFlash card attached to the Xilinx SystemACE controller. So far, root in initramfs works and after boot, I can mount and use said partition, no problem. But if I try to use it right from the getgo with the "root=/dev/xsa2" kernel command line parameter, the system hangs with [...] Freeing unused kernel memory: 143k freed Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004 And that's it - no regdump, no call trace, no further nothing from the serial console, even though kernel has been configured with debugging enabled. Now, I'm pretty new at this, so is there something else I should be doing to see something more informative from the kernel?

  Read the article

• how to fix "BusyBox v1.17.1 (Ubuntu 1:1.17.1-10ubuntu1) built-in shell (ash) Enter 'help' for a list of built-in commands?"

  - by Joseph

  So I was using Ubuntu when suddenly the whole thing froze up and I had to reboot. And from that moment on, the system when it is starting up, prompts this little selection menu: GNU GRUB version 1.99~rc1-13ubuntu3 Ubuntu, with Linux 2.6.38-10-generic ubuntu, with Linux 2.6.38-10-generic (recovery mode) Previous Linux versions Memory test (memtest86+) Memory test (memtest86+, serial console 115200) I have chosen all of the available choices but all I get is another command line system that reads: BusyBox v1.17.1 (Ubuntu 1:1.17.1-10ubuntu1) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs): And honestly I can't do anything with it. Does anyone have any idea of what is going on and how I can get Ubuntu to work again?

  Read the article

• Configure a wireless network that accepts any WPA2-PSK network key

  - by Michel

  I recently bought a UART WiFi module ( this one ) and configured it with right SSID but wrong password( and I don't know what it is ). The problem is that I can't reset this module to its manufacture settings and I can't connect to this module via serial port to configure it with some wire or cable. But I'm sure that my module is trying to connect my access point but with wrong network key ( because in logs of my access point I can see my module that trying to connect but it can't ) So, I wonder to know is there any way to create or configure a network (using some access point or something else) based on WPA2 Personal security that accepts any WPA2-PSK passwords ? Or is there any other solution for this problem ? If no, is there anyway to see what password this module using to connect to that network ? ( If yes, then I can change password of my network to that password and access to this module's admin panel ) I tried create an open network ( without any security key ) but my module just searches for WPA2 based networks ( I think ).

  Read the article

• Recover a lost IBM DS4300 SAN password?

  - by Daniel

  I have a pair of IBM DS4300 SAN units that I need to perform a firmware upgrade on. Unfortunately the admin passwords on these units have been lost and now need to be reset. I had hoped the default password of 'infiniti' would work but it seems that it must have been changed. I know the method here is to contact IBM but the cost of that phone call is ludicrous if someone out here knows what they're going to tell me to do. These units are out of warranty and the cost of support is beyond what we have the budget for. Is there an interrupt I can enter during the boot process (similar to a cisco password recovery) or is there a hardware/software tool I require? Please, if anyone has ever gone through the process of an IBM password recovery I’m asking for a little help. EDIT: Just to clarify, the password I need to reset is the one used for serial cable access and not for storage manager. Sorry if I have caused more confusion.

  Read the article

• Assistance in setting up new APC Smart-UPS RT on a new VMware enviroment

  - by user38085

  I'm new to the realm of setting up a APC Smart-UPS RT 8000VA UPS with a management network card (AP9618). The project calls for the upgrade of the firmware for the network card to the newest and greatest. It also calls for the Powerchute Business Software to be installed with notifications setup per email for temperature, shutdown, and battery low. I know I'll have to use the serial cable to flash the firmware and install the software on one server 2003 box. Also on that server I'll have to install the software and setup the GUI (IP address) interface. Whats confusing the most is the whole process, and steps to use without taking down the network, which would be very bad. In flashing the firmware does it take down the UPS? Do i have to run BOOTP commands to setup the network card? Also no agents will be used on any of the VWware OS's and no SNMP trap will be used.

  Read the article

• ufw portforwarding to virtualbox guest

  - by user85116

  My goal is to be able to connect using remote desktop on my desktop machine, to windows xp running in virtualbox on my linux server. My setup: server = debian squeeze, 64 bit, with a public IP address (host) virtualbox-ose 3.2.10 (from debian repo) windows xp running inside VBox as a guest; bridged networking mode in VBox, ip = 192.168.1.100 ufw as the firewall on debian, 3 ports are opened: 22 / ssh, 80 / apache, and 3389 for remote desktop My problem: If I try to use remote desktop on my home computer, I am unable to connect to the windows guest. If I first "ssh -X -C" into the debian server, then run "rdesktop 192.168.1.100", I am able to connect without issue. The windows firewall was configured to allow remote desktop connections, and I've even turned it off (as it is redundant here) to see if that was the problem but it made no difference. Since I am able to connect from inside the local subnet, I suspect that I have not setup my debian firewall correctly to handle connections from outside the LAN. Here is what I've done... First my ufw status: ufw status Status: active To Action From -- ------ ---- 22 ALLOW Anywhere 80 ALLOW Anywhere 3389 ALLOW Anywhere I edited /etc/ufw/sysctl.conf and added: net/ipv4/ip_forward=1 Edited /etc/default/ufw and added: DEFAULT_FORWARD_POLICY="ACCEPT" Edited /etc/ufw/before.rules and added: # setup port forwarding to forward rdp to windows VM *nat :PREROUTING - [0:0] -A PREROUTING -i eth0 -p tcp --dport 3389 -j DNAT --to-destination 192.168.1.100 -A PREROUTING -i eth0 -p udp --dport 3389 -j DNAT --to-destination 192.168.1.100 COMMIT # Don't delete these required lines, otherwise there will be errors *filter <snip> Restarted the firewall etc., but no connection. My log files on the debian host show this (my public ip address was removed for this posting but it is correct in the actual log): Feb 6 11:11:21 localhost kernel: [171991.856941] [UFW AUDIT] IN=eth0 OUT=eth0 SRC=aaa.bbb.ccc.dd DST=192.168.1.100 LEN=60 TOS=0x00 PREC=0x00 TTL=45 ID=27518 DF PROTO=TCP SPT=54201 DPT=3389 WINDOW=5840 RES=0x00 SYN URGP=0 Feb 6 11:11:21 localhost kernel: [171991.856963] [UFW ALLOW] IN=eth0 OUT=eth0 SRC=aaa.bbb.ccc.dd DST=192.168.1.100 LEN=60 TOS=0x00 PREC=0x00 TTL=45 ID=27518 DF PROTO=TCP SPT=54201 DPT=3389 WINDOW=5840 RES=0x00 SYN URGP=0 Feb 6 11:11:24 localhost kernel: [171994.856701] [UFW AUDIT] IN=eth0 OUT=eth0 SRC=aaa.bbb.ccc.dd DST=192.168.1.100 LEN=60 TOS=0x00 PREC=0x00 TTL=45 ID=27519 DF PROTO=TCP SPT=54201 DPT=3389 WINDOW=5840 RES=0x00 SYN URGP=0 Feb 6 11:11:24 localhost kernel: [171994.856723] [UFW ALLOW] IN=eth0 OUT=eth0 SRC=aaa.bbb.ccc.dd DST=192.168.1.100 LEN=60 TOS=0x00 PREC=0x00 TTL=45 ID=27519 DF PROTO=TCP SPT=54201 DPT=3389 WINDOW=5840 RES=0x00 SYN URGP=0 Feb 6 11:11:30 localhost kernel: [172000.856656] [UFW AUDIT] IN=eth0 OUT=eth0 SRC=aaa.bbb.ccc.dd DST=192.168.1.100 LEN=60 TOS=0x00 PREC=0x00 TTL=45 ID=27520 DF PROTO=TCP SPT=54201 DPT=3389 WINDOW=5840 RES=0x00 SYN URGP=0 Feb 6 11:11:30 localhost kernel: [172000.856678] [UFW ALLOW] IN=eth0 OUT=eth0 SRC=aaa.bbb.ccc.dd DST=192.168.1.100 LEN=60 TOS=0x00 PREC=0x00 TTL=45 ID=27520 DF PROTO=TCP SPT=54201 DPT=3389 WINDOW=5840 RES=0x00 SYN URGP=0 Although this is the current setup / configuration, I've also tried several variations of this; I thought maybe the ISP would be blocking 3389 for some reason and tried using different ports, but again there was no connection. Any ideas...? Did I forget to modify some file somewhere?

  Read the article

• SD to PCI adapter

  - by vy32

  We are looking for a way to plug a SD card into a PCI slot without going through a USB interface. We want to read the SD card's serial number directly and issue SD commands. The Chumby and the Google Android G1 phones both have SD slots that you can read from Linux without going through USB, but the Chumby only has a single SD card that's used for booting, and the G1 doesn't have any other reasonable storage if you use the SD card for that purpose. I'd really like a desktop with a few SD slots that are directly accessible. Anybody know of anything??

  Read the article

• Can't start httpd 2.4.9 with self-signed SSL certificate

  - by Smollet

  I cannot start the httpd 2.4.9 (tried 2.4.x too) on CentOS 6.5 with the simplest SSL config possible. The openssl version installed on the machine is OpenSSL 1.0.1e-fips 11 Feb 2013 (I've upgraded it using 'yum update' to the latest patched version as well) I have compiled and installed the httpd 2.4.9 using the following commands: ./configure --enable-ssl --with-ssl=/usr/local/ssl/ --enable-proxy=shared --enable-proxy_wstunnel=shared --with-apr=apr-1.5.1/ --with-apr-util=apr-util-1.5.3/ make make install Now I'm generating the default self-signed certificate as described in the CentOS HowTo: openssl genrsa -out ca.key 2048 openssl req -new -key ca.key -out ca.csr openssl x509 -req -days 365 -in ca.csr -signkey ca.key -out ca.crt cp ca.crt /etc/pki/tls/certs cp ca.key /etc/pki/tls/private/ca.key cp ca.csr /etc/pki/tls/private/ca.csr Here is my httpd-ssl.conf file: Listen 443 SSLCipherSuite HIGH:MEDIUM:!aNULL:!MD5 SSLPassPhraseDialog builtin SSLSessionCache "shmcb:/usr/local/apache2/logs/ssl_scache(512000)" SSLSessionCacheTimeout 300 <VirtualHost *:443> SSLEngine on SSLCertificateFile /etc/pki/tls/certs/ca.crt SSLCertificateKeyFile /etc/pki/tls/private/ca.key <FilesMatch "\.(cgi|shtml|phtml|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory "/usr/local/apache2/cgi-bin"> SSLOptions +StdEnvVars </Directory> BrowserMatch "MSIE [2-5]" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 CustomLog "/usr/local/apache2/logs/ssl_request_log" \ "%t %h %{SSL_PROTOCOL}x %{SSL_CIPHER}x \"%r\" %b" </VirtualHost> when I start httpd using bin/apachectl -k start I get following errors in the error_log: Wed Jun 04 00:29:27.995654 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01887: Init: Initializing (virtual) servers for SSL [Wed Jun 04 00:29:27.995726 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:29:27.995863 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:29:27.996111 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_util_ssl.c(343): AH02412: [192.168.9.128:443] Cert matches for name '192.168.9.128' [subject: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / issuer: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / serial: AF04AF31799B7695 / notbefore: Jun 3 22:26:45 2014 GMT / notafter: Jun 3 22:26:45 2015 GMT] [Wed Jun 04 00:29:27.996122 2014] [ssl:info] [pid 24021:tid 139640404293376] AH02568: Certificate and private key 192.168.9.128:443:0 configured from /etc/pki/tls/certs/ca.crt and /etc/pki/tls/private/ca.key [Wed Jun 04 00:29:27.996209 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:29:27.996280 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:29:27.996295 2014] [ssl:emerg] [pid 24021:tid 139640404293376] AH02572: Failed to configure at least one certificate and key for 192.168.9.128:443 [Wed Jun 04 00:29:27.996303 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:0906D06C:PEM routines:PEM_read_bio:no start line (Expecting: DH PARAMETERS) -- Bad file contents or format - or even just a forgotten SSLCertificateKeyFile? [Wed Jun 04 00:29:27.996308 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:0906D06C:PEM routines:PEM_read_bio:no start line (Expecting: EC PARAMETERS) -- Bad file contents or format - or even just a forgotten SSLCertificateKeyFile? [Wed Jun 04 00:29:27.996318 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:140A80B1:SSL routines:SSL_CTX_check_private_key:no certificate assigned [Wed Jun 04 00:29:27.996321 2014] [ssl:emerg] [pid 24021:tid 139640404293376] AH02312: Fatal error initialising mod_ssl, exiting. AH00016: Configuration Failed I then try to generate missing DH PARAMETERS and EC PARAMETERS: openssl dhparam -outform PEM -out dhparam.pem 2048 openssl ecparam -out ec_param.pem -name prime256v1 cat dhparam.pem ec_param.pem >> /etc/pki/tls/certs/ca.crt And it mitigates the error but the next comes out: [Wed Jun 04 00:34:05.021438 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01887: Init: Initializing (virtual) servers for SSL [Wed Jun 04 00:34:05.021487 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:34:05.021874 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:34:05.022050 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_util_ssl.c(343): AH02412: [192.168.9.128:443] Cert matches for name '192.168.9.128' [subject: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / issuer: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / serial: AF04AF31799B7695 / notbefore: Jun 3 22:26:45 2014 GMT / notafter: Jun 3 22:26:45 2015 GMT] [Wed Jun 04 00:34:05.022066 2014] [ssl:info] [pid 24089:tid 140719371077376] AH02568: Certificate and private key 192.168.9.128:443:0 configured from /etc/pki/tls/certs/ca.crt and /etc/pki/tls/private/ca.key [Wed Jun 04 00:34:05.022285 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(1016): AH02540: Custom DH parameters (2048 bits) for 192.168.9.128:443 loaded from /etc/pki/tls/certs/ca.crt [Wed Jun 04 00:34:05.022389 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(1030): AH02541: ECDH curve prime256v1 for 192.168.9.128:443 specified in /etc/pki/tls/certs/ca.crt [Wed Jun 04 00:34:05.022397 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:34:05.022464 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:34:05.022478 2014] [ssl:emerg] [pid 24089:tid 140719371077376] AH02572: Failed to configure at least one certificate and key for 192.168.9.128:443 [Wed Jun 04 00:34:05.022488 2014] [ssl:emerg] [pid 24089:tid 140719371077376] SSL Library Error: error:140A80B1:SSL routines:SSL_CTX_check_private_key:no certificate assigned [Wed Jun 04 00:34:05.022491 2014] [ssl:emerg] [pid 24089:tid 140719371077376] AH02312: Fatal error initialising mod_ssl, exiting. AH00016: Configuration Failed I have tried to generate the simple certificate/key pair exactly as described in the httpd docs Unfortunately, I still get exact same errors as above. I've seen a bug report with the similar issue: https://issues.apache.org/bugzilla/show_bug.cgi?id=56410 But the openssl version I have is reported as working there. I've also tried to apply the patch from the report as well as build the latest 2.4.x branch with no success, I get the same errors as above. I have also tried to create a short chain of certificates and set the root CA certificate using SSLCertificateChainFile directive. That didn't help either, I get exact same errors as above. I'm not interested in setting up hardened security, etc. The only thing I need is to start httpd with the simplest SSL config possible to continue testing proxy config for the mod_proxy_wstunnel Had anybody encountered and solved this issue? Is my sequence for creating a self-signed certificate incorrect? I'd appreciate any help very much!

  Read the article

• Does likewise-open > version 5.4 contain CIFS support?

  - by Ben Andken

  I'm trying to get the CIFS server working in likewise-open. I've found this set of instructions and everything seems to work until I try to connect ([url]http://www.likewise.com/resources/documentation_library/manuals/cifs/likewise-cifs-smb-file-server-guide.html#id2765992):[/url] 1.6. Build and Configure a Standalone Likewise-CIFS Server This section demonstrates how to build and configure a standalone instance of Likewise-CIFS from the command line. The following procedure assumes that you want to set up Likewise-CIFS on a Linux server to share files with Windows computers in a network without Active Directory. This procedure also assumes you know how to build Linux applications from their source code and then install them. Download Likewise-CIFS from its open source git location: $ git clone git://git.likewiseopen.org/ Download, build, and install the following tools. The tools listed are known to work, but earlier or later versions might work as well. Also, instead of downloading the tools, you might be able to install them on your platform with apt-get or some other means. http://ftp.gnu.org/gnu/autoconf/autoconf-2.65.tar.gz http://ftp.gnu.org/gnu/automake/automake-1.9.6.tar.gz http://ftp.gnu.org/gnu/libtool/libtool-2.2.6a.tar.gz http://pkgconfig.freedesktop.org/releases/pkg-config-0.23.tar.gz gcc --version 3.x or greater Build Likewise-CIFS: $ cd likewise-open $ build/mkcomp --debug all Install Likewise-CIFS: $ sudo su $ cd staging/install-root $ tar cf - . | (cd / && tar xvf -) Make sure Samba is not running: $ /etc/init.d/smb stop Make sure SELinux is either disabled or set to permissive. Make sure the ports required by Likewise are open. For a list of ports that Likewise uses, see the Likewise Open Installation and Administration Guide. Configure Likewise Open: $ /etc/init.d/lwsmd start $ for i in /etc/likewise/*.reg; do /opt/likewise/bin/lwregshell upgrade $i; done $ /etc/init.d/lwsmd stop $ /etc/init.d/lwsmd start $ /opt/likewise/bin/lwsm start srvsvc $ /opt/likewise/bin/domainjoin-cli configure --enable nsswitch Add a user account to the local Likewise provider database. In the following example, substitute the account name that you want for newuser. $ /opt/likewise/bin/lw-add-user --home /home/newuser --shell /bin/bash newuser Successfully added user newuser Enable the user and set the password: $ /opt/likewise/bin/lw-mod-user --enable-user --set-password newuser New Password: ********** Successfully modified user newuser Look up new user's identity as follows. Substitute the value from the command hostname -s for the hostname. Keep in mind that Likewise truncates a hostname longer than 15 characters to the first 15 characters of the string. % id hostname\\newuser uid=2000(HOSTNAME\newuser) gid=1800(HOSTNAME\Likewise Users) groups=1800(HOSTNAME\Likewise Users) context=system_u:system_r:unconfined_t:s0 Make a CIFS directory for the user: mkdir /lwcifs/newuser chown 2000:1800 /lwcifs/newuser From a Windows computer, map the Likewise-CIFS drive share: Computer->Map Network Drive... Folder: \\IP_hostname\c$ Click "Finish" Username: hostname\newuser Password: user_password The last step fails when I try to connect. I've tried with Windows XP Pro and Windows 7 Pro. The rest of the directions only appear to work for version 5.4 (the one that shipped with 10.04). For 12.04, version 6.1 is the only one available and it doesn't appear to have the srvsvc module mentioned in these instructions. Is CIFS support dropped in the 6.1 version of likewise-open?

  Read the article

• Reset DRAC/MC password on Dell BladeCentre 1855

  - by Farseeker

  I have a Dell Blade Centre 1855, and nobody knows what the root password for the DRAC/MC card in the blade chassis is (I tried root/calvin). I do not have IP access to the DRAC/MC, nor do I have physical access to the back of the blade centre to access the DRAC/MC module. I do have serial access (and can see the login prompt in hyperterm). I do have physical access to the FRONT of the chassis (the back of the cabinet is locked and lo-and-behold the key cannot be found). Does anyone know how to reset the password? Every piece of literature I find on the internet tells me I need to log in, or run racadm on the host machine (which I can't, because it's inside a blade chassis). If someone does know how to do it with physical access to the back of the bladecentre, please post it anyway, as I'm sure I'll get access to the back of the cabinet one day)

  Read the article

• APCUPSD and Hyper V R2

  - by Jason Berg

  I'm about to deploy a Windows Server 2008 R2 machine with the Hyper V role. I'd like to get away from having to use a network management card with my APC UPS as I'm only shutting down 1 server (it just seems like an unneeded point of failure). I'd like to look into using apcupsd instead. Will this work properly if I use a serial connection? Have you got it working yourself? How is the SNMP monitoring? I really like being able to easily monitor my UPS with SNMP when powerchute is installed. Will I be sacrificing this completely? Is the network management card really the way to go with this? If so, why? Bonus question: Is there a better UPS out there that I should be recommending in the future?

  Read the article

• Original Windows 7 Home Premium on Acer Aspire 5740G

  - by elr

  Is it posible to get the original Windows 7 Home Premium 64bit for the Acer Aspire 5740G? I bought this notebook and the license for this Windows is in the package. There is an partition with the data for the recovery. But than, there are a lot of senseless application which I don't want to use. I'm searchin for the complete clear Windows 7 Home Premium. I tried to download the original Windows 7 Home Premium and entered the serial key of the bottom of the laptop but I can't activate my Windows with this key. Any ideas or experiens with this?

  Read the article

• How Do I Enable My Ubuntu Server To Host Various SSL-Enabled Websites?

  - by Andy Ibanez

  Actually, I Have looked around for a few hours now, but I can't get this to work. The main problem I'm having is that only one out of two sites works. I have my website which will mostly be used for an app. It's called atajosapp.com . atajosapp.com will have three main sites: www.atajosapp.com <- Homepage for the app. auth.atajosapp.com <- Login endpoint for my API (needs SSL) api.atajosapp.com <- Main endpoint for my API (needs SSL). If you attempt to access api.atajosapp.com it works. It will throw you a 403 error and a JSON output, but that's fully intentional. If you try to access auth.atajosapp.com however, the site simply doesn't load. Chrome complains with: The webpage at https://auth.atajosapp.com/ might be temporarily down or it may have moved permanently to a new web address. Error code: ERR_TUNNEL_CONNECTION_FAILED But the website IS there. If you try to access www.atajosapp.com or any other HTTP site, it connects fine. It just doesn't like dealing with more than one HTTPS websites, it seems. The VirtualHost for api.atajosapp.com looks like this: <VirtualHost *:443> DocumentRoot /var/www/api.atajosapp.com ServerName api.atajosapp.com SSLEngine on SSLCertificateFile /certificates/STAR_atajosapp_com.crt SSLCertificateKeyFile /certificates/star_atajosapp_com.key SSLCertificateChainFile /certificates/PositiveSSLCA2.crt </VirtualHost> auth.atajosapp.com Looks very similar: <VirtualHost *:443> DocumentRoot /var/www/auth.atajosapp.com ServerName auth.atajosapp.com SSLEngine on SSLCertificateFile /certificates/STAR_atajosapp_com.crt SSLCertificateKeyFile /certificates/star_atajosapp_com.key SSLCertificateChainFile /certificates/PositiveSSLCA2.crt </VirtualHost> Now I have found many websites that talk about possible solutions. At first, I was getting a message like this: _default_ VirtualHost overlap on port 443, the first has precedence But after googling for hours, I managed to solve it by editing both apache2.conf and ports.conf. This is the last thing I added to ports.conf: <IfModule mod_ssl.c> NameVirtualHost *:443 # SSL name based virtual hosts are not yet supported, therefore no # NameVirtualHost statement here NameVirtualHost *:443 Listen 443 </IfModule> Still, right now only api.atajosapp.com and www.atajosapp.com are working. I still can't access auth.atajosapp.com. When I check the error log, I see this: Init: Name-based SSL virtual hosts only work for clients with TLS server name indication support (RFC 4366) I don't know what else to do to make both sites work fine on this. I purchased a Wildcard SSL certificate from Comodo that supposedly secures *.atajosapp.com, so after hours trying and googling, I don't know what's wrong anymore. Any help will be really appreciated. EDIT: I just ran the apachectl -t -D DUMP_VHOSTS command and this is the output. Can't make much sense of it...: root@atajosapp:/# apachectl -t -D DUMP_VHOSTS apache2: Could not reliably determine the server's fully qualified domain name, using atajosapp.com for ServerName [Thu Nov 07 02:01:24 2013] [warn] NameVirtualHost *:443 has no VirtualHosts VirtualHost configuration: wildcard NameVirtualHosts and _default_ servers: *:443 is a NameVirtualHost default server api.atajosapp.com (/etc/apache2/sites-enabled/api.atajosapp.com:1) port 443 namevhost api.atajosapp.com (/etc/apache2/sites-enabled/api.atajosapp.com:1) port 443 namevhost auth.atajosapp.com (/etc/apache2/sites-enabled/auth.atajosapp.com:1) *:80 is a NameVirtualHost default server atajosapp.com (/etc/apache2/sites-enabled/000-default:1) port 80 namevhost atajosapp.com (/etc/apache2/sites-enabled/000-default:1)

  Read the article

• ifconfig return "unknown interface: no such device"

  - by xolstice

  I'm trying to install a Linux driver for my wireless network card (D-Link DWL-G510) on my Red Hat Linux 7.1 machine with a 2.4.37.9 kernel. I downloaded the serial monkey driver from the sourceforge site and was able to successfully compile the rt73 module and load it into the kernel. The problem now is that everytime I issue the command ifconfig wlan0 up it keeps returning with the following error message: wlan0: unknown interface: No such device. I'm at a loss as to what to do here. I specifed wlan0 as the alias for the rt73 module in the modules.conf and also tried to load the driver with the command modprobe rt73 ifname=wlan0 (this specifies the interface name according to the instructions packaged in the driver), but the error message still keeps coming up. Is there something else I need to do in Linux to configure the wlan0 part or is the module not recognizing the wireless network card? It would be quite strange if it is the later since all information from the Internet is indicating this is the linux driver I should be using for mentioned wireless card.

  Read the article

• Adobe Volume License for Indesign Digital Download Location?

  - by elistp

  We recently purchased a volume license for Adobe Indesign from Dell. We received an e-mail for the order that contains the serial #. However, there is no information on how to obtain Adobe Indesign from the Adobe licensing portal. This is our first time dealing with Adobe volume licensing so I'm a bit lost as to what we're suppose to do. I've googled around a little and found an Adobe License Portal but I do not have access to it. Does anyone with experience concerning Adobe volume licensing have any idea what we're suppose to do to get a download of our purchase?

  Read the article

• Logging to MySQL without empty rows/skipped records?

  - by Lee Ward

  I'm trying to figure out how to make Squid proxy log to MySQL. I know ACL order is pretty important but I'm not sure if I understand exactly what ACLs are or do, it's difficult to explain, but hopefully you'll see where I'm going with this as you read! I have created the lines to make Squid interact with a helper in squid.conf as follows: external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log The external ACL helper (mysql_lg.php) is a PHP script and is as follows: error_reporting(0); if (! defined(STDIN)) { define("STDIN", fopen("php://stdin", "r")); } $res = mysql_connect('localhost', 'squid', 'testsquidpw'); $dbres = mysql_select_db('squid', $res); while (!feof(STDIN)) { $line = trim(fgets(STDIN)); $fields = explode(' ', $line); $user = rawurldecode($fields[0]); $cli_ip = rawurldecode($fields[1]); $protocol = rawurldecode($fields[2]); $uri = rawurldecode($fields[3]); $q = "INSERT INTO logs (id, user, cli_ip, protocol, url) VALUES ('', '".$user."', '".$cli_ip."', '".$protocol."', '".$uri."');"; mysql_query($q) or die (mysql_error()); if ($fault) { fwrite(STDOUT, "ERR\n"); }; fwrite(STDOUT, "OK\n"); } The configuration I have right now looks like this: ## Authentication Handler auth_param ntlm program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-ntlmssp auth_param ntlm children 30 auth_param negotiate program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-basic auth_param negotiate children 5 # Allow squid to update log external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log acl localnet src 172.16.45.0/24 acl AuthorizedUsers proxy_auth REQUIRED acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl CONNECT method CONNECT acl blockeddomain url_regex "/etc/squid3/bl.acl" http_access deny blockeddomain deny_info ERR_BAD_GENERAL blockeddomain # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # Allow the internal network access to this proxy http_access allow localnet # Allow authorized users access to this proxy http_access allow AuthorizedUsers # FINAL RULE - Deny all other access to this proxy http_access deny all From testing, the closer to the bottom I place the logging lines the less it logs. Oftentimes, it even places empty rows in to the MySQL table. The file-based logs in /var/log/squid3/access.log are correct but many of the rows in the access logs are missing from the MySQL logs. I can't help but think it's down to the order I'm putting lines in because I want to log everything to MySQL, unauthenticated requests, blocked requests, which category blocked a specific request. The reason I want this in MySQL is because I'm trying to have everything managed via a custom web-based frontend and want to avoid using any shell commands and access to system log files if I can help it. The end result is to make it as easy as possible to maintain without keeping staff waiting on the phone whilst I add a new rule and reload the server! Hopefully someone can help me out here because this is very much a learning experience for me and I'm pretty stumped. Many thanks in advance for any help!

  Read the article

• My datacard goes online but doesn't gives internet access (Fedora 14).

  - by Harsh

  I am using MTS datacard. I have usb_modeswitch installed and have configured the wvdial.conf file. When I do sudo wvdial cdma, the IPs and DNS addresses are also allocated but I still cant access internet. The reply to dmesg | grep -e 'tty' -e 'modem' is: [ 0.000000] console [tty0] enabled [ 11.098238] USB Serial support registered for GSM modem (1-port) [ 11.098352] option 6-1:1.0: GSM modem (1-port) converter detected [ 11.102170] usb 6-1: GSM modem (1-port) converter now attached to ttyUSB0 [ 11.102207] option 6-1:1.1: GSM modem (1-port) converter detected [ 11.102334] usb 6-1: GSM modem (1-port) converter now attached to ttyUSB1 [ 11.102364] option 6-1:1.2: GSM modem (1-port) converter detected [ 11.102488] usb 6-1: GSM modem (1-port) converter now attached to ttyUSB2 [ 11.102522] option 6-1:1.3: GSM modem (1-port) converter detected [ 11.102643] usb 6-1: GSM modem (1-port) converter now attached to ttyUSB3 [ 11.102672] option 6-1:1.4: GSM modem (1-port) converter detected [ 11.102793] usb 6-1: GSM modem (1-port) converter now attached to ttyUSB4 [ 11.103074] option: v0.7.2:USB Driver for GSM modems Can anyone tell me what shall I do?

  Read the article

• Proper network configuration for a KVM guest to be on the same networks at the host

  - by Steve Madsen

  I am running a Debian Linux server on Lenny. Within it, I am running another Lenny instance using KVM. Both servers are externally available, with public IPs, as well as a second interface with private IPs for the LAN. Everything works fine, except the VM sees all network traffic as originating from the host server. I suspect this might have something to do with the iptables-based firewall I'm running on the host. What I'd like to figure out is: how to I properly configure the host's networking such that all of these requirements are met? Both host and VMs have 2 network interfaces (public and private). Both host and VMs can be independently firewalled. Ideally, VM traffic does not have to traverse the host firewall. VMs see real remote IP addresses, not the host's. Currently, the host's network interfaces are configured as bridges. eth0 and eth1 do not have IP addresses assigned to them, but br0 and br1 do. /etc/network/interfaces on the host: # The primary network interface auto br1 iface br1 inet static address 24.123.138.34 netmask 255.255.255.248 network 24.123.138.32 broadcast 24.123.138.39 gateway 24.123.138.33 bridge_ports eth1 bridge_stp off auto br1:0 iface br1:0 inet static address 24.123.138.36 netmask 255.255.255.248 network 24.123.138.32 broadcast 24.123.138.39 # Internal network auto br0 iface br0 inet static address 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 bridge_ports eth0 bridge_stp off This is the libvirt/qemu configuration file for the VM: <domain type='kvm'> <name>apps</name> <uuid>636b6620-0949-bc88-3197-37153b88772e</uuid> <memory>393216</memory> <currentMemory>393216</currentMemory> <vcpu>1</vcpu> <os> <type arch='i686' machine='pc'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='cdrom'> <target dev='hdc' bus='ide'/> <readonly/> </disk> <disk type='file' device='disk'> <source file='/raid/kvm-images/apps.qcow2'/> <target dev='vda' bus='virtio'/> </disk> <interface type='bridge'> <mac address='54:52:00:27:5e:02'/> <source bridge='br0'/> <model type='virtio'/> </interface> <interface type='bridge'> <mac address='54:52:00:40:cc:7f'/> <source bridge='br1'/> <model type='virtio'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target port='0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes' keymap='en-us'/> </devices> </domain> Along with the rest of my firewall rules, the firewalling script includes this command to pass packets destined for a KVM guest: # Allow bridged packets to pass (for KVM guests). iptables -A FORWARD -m physdev --physdev-is-bridged -j ACCEPT (Not applicable to this question, but a side-effect of my bridging configuration appears to be that I can't ever shut down cleanly. The kernel eventually tells me "unregister_netdevice: waiting for br1 to become free" and I have to hard reset the system. Maybe a sign I've done something dumb?)

  Read the article

• How to update grub with puppet?

  - by Tombart

  I would like to change a line in /etc/default/grub with puppet to this: GRUB_CMDLINE_LINUX="cgroup_enable=memory" I've tried to used augeas which seems to do this magic: exec { "update_grub": command => "update-grub", refreshonly => true, } augeas { "grub-serial": context => "/files/etc/default/grub", changes => [ "set /files/etc/default/grub/GRUB_CMDLINE_LINUX[last()] cgroup_enable=memory", ], notify => Exec['update_grub'], } It seems to work, but the result string is not in quotes and also I want to make sure that any other values will be separated by space. GRUB_CMDLINE_LINUX=cgroup_enable=memory Is there some mechanism how to append values and escape the whole thing? GRUB_CMDLINE_LINUX="quiet splash cgroup_enable=memory"

  Read the article

• Windows 8 Upgrade : From Windows 7 Trial

  - by Golmaal

  This is a bit complicated it seems. I own Windows Vista Ultimate 64-bit (Retail). It was okay, but around a couple of weeks ago I had some system crash and at that time I decided that I will install Windows 8 as soon as it comes out. However, because of some problems in Vista, at the time of crash, I installed Windows 7 trial. I had some urgent work to do which I accomplished and then I switched the PC off. Now I have purchased Windows 8 Pro Upgrade ($40 version). If I go for a clean install, will it be able to install Windows 8 on not-activated Windows 7? During activation, if it asks for Vista serial number, I can provide it. Or will I first have to install Vista and then only it will allow me to install Windows 8? Also, I used the Upgrade Assistant to download Windows 8 on my laptop (Windows 7 OEM). Will it work on my above mentioned desktop?

  Read the article

• Map /dev/bus/usb node to /sys node on Linux

  - by Cody Brocious

  I'm using libusb to find and access a USB device, but once I get the information I need from there, I need to map it to a /sys node. This could be to the actual USB bus it's on, the /sys/bus/usb-serial node (which is where I'm going to get eventually), or effectively anywhere else since I can walk the tree from there. I can get to a /dev/bus/usb node easily enough, but I'm a bit lost from there. What would be the best route to perform this mapping? Alternatively, a way to get the /dev/ttyUSB device node for a /dev/bus/usb node would work as well, since it gets me the same result.

  Read the article

• named-checkzone reports 'ns.example.com.ns' has no address records (A or AAAA)

  - by hydroparadise

  The first thing I see wrong is that its a recursion problem. But I'm not sure where the problems lie in my reverse lookup file. ns should report back as ns.example.com but instead getting ns.example.com.ns. Of course it wouldn't find any entries for that name because there isn't one, nor is it supposed to. Here's my reverse file: $TTL 86400 @ IN SOA ns.example.com root.example.com. ( 16071990 ; Serial 3600 ; Refresh 1800 ; Retry 604800 ; Expire 86400 ; Minimum TTL ) @ IN NS ns.example.com It's not extraordinarily complicated. What my question is, what other files affect the output for named-checkzone when checking a name against the revers file?

  Read the article

• SATA Backward compatibility? [closed]

  - by Fladur

  Possible Duplicate: Can I connect a SATA-II hard drive to a SATA-I connection? Hello everyone One of my system is really old, but I still use it, right now, the HDD is and old IDE drive that is starting to fail (I got to many damaged sectors) and I'm planing to replace it. The motherboard supports Serial ATA 1 and I have a real nice offer on a SATA 2 drive, can I use that drive on a SATA 1 interface (obviously with reduced speed) just like a USB 2.0 device on a 1.0 port? Thanks in advance.

  Read the article

• Help make sense of a KillDisk error/log

  - by user284194

  I have a hard drive that I've been trying to reformat. I tried reformatting it in the windows XP and 7 installers, and in an Ubuntu live cd with gparted. I tried using dd to 'zero' the drive as well with no success. Finally I ran across KillDisk after a search. I tried to zero the disk again with KillDisk and after 8 hours of zeroing I get the following errors in the log: ----------------------------------------Erase Session Begin--------------------------------------- 2010-03-23 19:35:54 Active@ KILLDISK for Windows Build 5.1.39 started Target: WDC WD2500KS-00MJB0 232.9 GB Located on: WDC WD2500KS-00MJB0 (Serial number: WD-WCANK9604799) Erase method: One Pass Zeros (1 pass) Passes: 1 Bad (unwritable) sectors detected from 1701 to 488397167 on Hard Disk 1. Error (the handle is invalid) refreshing device Hard Disk 1. Error (the handle is invalid) reading sector 0 on 81h. 2010-03-24 02:28:25 Total number of erased device(s): 0, partition(s): 0 -----------------------------------------Erase Session End---------------------------------------- Is the drive dead?

  Read the article

< Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >