Search Results

Search found 13652 results on 547 pages for 'full'.

Page 86/547 | < Previous Page | 82 83 84 85 86 87 88 89 90 91 92 93  | Next Page >

  • Low FPS in some games, but hardware not fully used

    - by Mario De Schaepmeester
    I just did a little funny experiment in the game/sim "Train Simulator 2013". I normally have good FPS in it (around 30) at full settings. What I did was make a really, really long train so that the calculations the sim needed to make were enormous (the sim is quite realistic, it takes all things into account like speed/acceleration, G-forces, comfort levels, possible wheel slip and many more, and most of those things on each carriage seperately). This resulted in only 14FPS as reported by the game, but it felt more like 8FPS or so. I have a Logitech G15 keyboard which has an LCD, and it allows me to monitor CPU/RAM and video card load on it. The strange thing is, all CPU cores were busy, but the total load was only about 60% maximum at all times. The video card was only on 30% load (possibly an important note, the memory was full, which is however not unusual for the game in question). The RAM had plenty of room and there weren't many operations as it didn't grow or shrink much. I just have the feeling that the game would run smoother if it used more of my hardware power. Why is it not doing so? I had the same in another game, The Elder Scrolls: Morrowind when using more than 100 mods (that all use scripting) and a few high res texture mods, + a full-on graphics improvement program. The engine is very old (2003), and so I thought this might be the cause (not being optimised for multithreading). I had thought of possible causes, like: The operating system doesn't let the games use all the resources. It doesn't make use of multi-threading appropriately. To eliminate the former, I tried a CPU stress tool and that got 100% CPU juice as I let it run, so the OS is not the problem. I gave its thread the "higher" priority though. My actual question In both games, I did things the engine was not really built to do or support. Can those games' framerate be limited cause of their own engine not being able to cope? What is the real reason and more importantly, can I help it? And in any case, could something actually be wrong with my hardware? It's all reasonably new, a couple of months, and I (almost) never experience any other trouble. Modern and much more demanding games work absolutely fine. Specs CPU: AMD Phenom II 965 X4 @ 3.4gHz RAM: 8GB of DDR3 RAM Video: MSI GTX560 (nVidia chip) with 1GB of GDDR5 memory OS: Windows 7 Ultimate 64 bit Nothing overclocked.

    Read the article

  • JavaOne Content Available for Free

    - by Tori Wieldt
    JavaOne content is available in video in three sizes, depending on if you want to have a sip, have a drink, or go to the proverbial firehose. Tall (Keynote Highlights) Go to the JavaOne playlist on the YouTube Java channel for highlights of the JavaOne Keynotes.  Grande (Keynotes in Full) Go to the Oracle Media Network JavaOne 2012 channel to view the keynotes in full (Community Keynote coming soon). Venti (All Sessions, BOFs and Tutorials) To view slides paired with audio of each session, go to the JavaOne content catalog (JavaOne homepage, click on JavaOne Technical Sessions) and select a session. If a video is available, you'll see "Media" in the right column. Look under "Presentation Download" to get the slides. Sessions are being made available as quickly as possible. "It's exciting to see Oracle take community stewardship so seriously," said Sharat Chander, Group Director for Java Technology Outreach. "Making all JavaOne sessions on video available online for free will helps make the future Java for everyone." Thanks to Oracle for funding this and providing to it to the Java Community for free.

    Read the article

  • Software for defining rules for folder permissions and monitoring deviations

    - by Kjensen
    Let's say a company has a large number of users, and each user has a home area. On each share used for home area folders, I would like to define some rules saying who is supposed to have which permissions on the folder. Then I would like to audit automatically, that this is actually the case and get some sort of report on deviations. So a rule for \MegaServer\Home01 could be defined something like: Domain Admins - Full Control Backup Agent - Read [Home folder owner] - Full Control I am talking about Windows platform and Windows servers, although I think it would most likely also work for *nix machines that expose Windows shares. Does software like this exist? I could roll my own basic version, but if something already exists, that is usually a better option. I am aware of tools to make displaying permissions easier (AccessEnum, DumpSec), but that is not what I am looking for.

    Read the article

  • Export to excel - COMMA issue

    - by 6242Y
    I want to put a string in an excel sheet from my Export to excel function. However my string is as follows: string : Red, red wine Go to my head Make me forget that I Still need and on my excel I get unexpected results , column change after comma and also column change when there is no full stop in front of an UPPER CASE alphabet. The Upper case alphabets (without a full stop before them) are also causing this (Go , Make . Still) How can I solve this issue ? I tried removing the spaces after the comma as var desc = ""; if (o.Description.Contains(',')) { var trimmedSplits = new List<string>(); var splits = o.Description.Split(','); foreach (var stringBits in splits) { desc = desc + stringBits.Trim() + ","; } desc = desc.Remove(desc.Length - 1); } dtRow[(int)ProductRangeExportToExcel.Description] = desc;

    Read the article

  • PS2 Eyetoy Recording Quality

    - by Fire
    I have Ubuntu 12.04 LTS and a PS2 eyetoy "Namtai". Don't worry - this is not the sterotypical " how do I get my eyetoy working" question. My eyetoy works fine on Cheese, gucview and various other media software like VLC. However, It seems like I am capped by 25fps. If I recall, the eyetoy is much better than this (~60fps) but cannot find any way to fix this. The best program that I have have found is VLC because its advanced options allow you to change many settings but the framerate setting appears to have no effect. What software or settings can I use to take full advantage of my eyetoy? To give you the full information I wish to attach multiple eyetoys to the system and record from all of them. (Security software like motion and zoneminder, I couldn't get installed correctly on my system- so I haven't tried those yet). edit - I tried the same camera on a Windows system and the frame rate is much better in VLC compared to the Ubuntu system. Mind you with default settings in Windows VLC, the resolution isn't great. However, in Skype for example the resolution is amazing and the framerate is good. It seems there must be some settings I am missing somewhere because it doesn't appear to be a hardware problem...

    Read the article

  • HTML5 - Does it have the power to handle a large 2D game with a huge world?

    - by user15858
    I have been using XNA game studio, but due to private reasons (as well as the ability to publish anywhere & my heavy interest in isogenic engine), I would like to switch to HTML5. However, I have very high 2D graphic demands for my game. The game itself will have a HDD size of anywhere between 6GB (min) to 12GB (max) which would be a full game deployed offline. The size of the images aren't significantly large, so streaming would be entirely possible if only those assets required were streamed as needed. The game has a massive file size because of the sheer amount of content. For some images or spritesheets, they would be quite massive. (ex. a very large Dragon, which if animated in a spritesheet would be split into two 4096x4096 sheets or one 8192x8192 sheet). Most assets would be very small, and about 7MB for a full character with 15 animations in every direction (all animations not required immediately) so in the size of a few hundred KB to download before the game loads. My question, however, is if the graphical power of HTML5 is enough to animate several characters on screen at once, when it flips through frames quite rapidly. All my sprites have about 25 frames per animation, 5 directions (a spritesheet for each direction & animation), and run at 30fps. Upon changing direction, animation, or a new character entering, spritesheets would change and be constantly loading/unloading. If I pack all directions in a single sheet, it would be about 2048x2048 per sheet. Most frameworks have no problem with this, but I am afraid from what I read that HTML5's graphical capabilities will limit me. Since it takes significant time simply to animate characters in any language, I'd like a quick answer.

    Read the article

  • Change AccountName/LoginName for a SharePoint User (SPUser)

    - by Rohit Gupta
    Consider the following: We have an account named MYDOMAIN\eholz. This accounts Active Directory Login Name changes to MYDOMAIN\eburrell Now this user was a active user in a Sharepoint 2010 team Site, and had a userProfile using the Account name MYDOMAIN\eholz. Since the AD LoginName changed to eburrell hence we need to update the Sharepoint User (SPUser object) as well update the userprofile to reflect the new account name. To update the Sharepoint User LoginName we can run the following stsadm command on the Server: STSADM –o migrateuser –oldlogin MYDOMAIN\eholz –newlogin MYDOMAIN\eburrell –ignoresidhistory However to update the Sharepoint 2010 UserProfile, i first tried running a Incremental/Full Synchronization using the User Profile Synchronization service… this did not work. To enable me to update the AccountName field (which is a read only field) of the UserProfile, I had to first delete the User Profile for MYDOMAIN\eholz and then run a FULL Synchronization using the User Profile Synchronization service which synchronizes the Sharepoint User Profiles with the AD profiles. Update: if you just run the STSADM –o migrateuser command… the profile also gets updated automatically. so all you need is to run the stsadm –o migrate user command and you dont need to delete and recreate the User Profile

    Read the article

  • Share folder with active directory group permissions

    - by Hihui
    I have a Debian as a member of our AD (which is a 2k3). I want to share 2 folders from our Debian. 1 with full access for everyone, the second only readable by group "ADM", and "PROD". Part of smb.conf: [global] workgroup = MYDOMAIN realm = MYDOMAIN.LOCAL netbios name = SERV-FTP wins server = "IP serv 2k3" security = domain [JUKEBOX] // full access path = /media/JUKEBOX/JUKEBOX comment = sharing writable = yes browsable = yes public = yes read only = no valid users = @ASYLUM\prod_std admin users = @ASYLUM\ADM [SOFTWARE] comment = Software path = /media/JUKEBOX/SOFTWARE valid users = @ASYLUM\prod_adv, @ASYLUM\ADM writable = yes read only = no My log : [2013/10/25 09:24:37.316643, 0] smbd/service.c:1055(make_connection_snum) canonicalize_connect_path failed for service SOFTWARE, path /media/JUKEBOX/SOFTWARE And, from my Windows's client, if i want to access on that folder : Windows can't access to \serv-ftp\software Where is the problem ... ? Thx !

    Read the article

  • New Nokia SDK 2.0 for Java (beta)

    - by Tori Wieldt
    Nokia recently launched the Asha 305, 306, and 311, which are full touch devices with smartphone-like functionality at a low price. This makes them particularly attractive to consumers in the developing and developed world who may not be able to afford a smartphone but have a strong demand for apps and the smartphone experience. The Asha phones are the latest addition to Nokia's Series 40 platform, all of which support Java ME. The SDK includes new Full Touch API's (e.g. supporting pinch zoom) and Sensor support delivering an enhanced App experience. It also adds improved Maps API support for creating socio-local apps. There are a number of improvements in the tools including the Nokia IDE for Java ME with in-build Device-SDK Manager. Many code examples, training videos, webinars and sample code will help get you started. Porting guides and sample code show you how to port your android app to Java ME. If you don't have access to the hardware you can use Remote Device Access to test on real hardware that's remotely hosted for free. You can also find Light Weight UI Toolkit (LWUIT) support, which can speed development significantly. Both In-App Advertising and In-App Purchase (beta) is supported. Here's a great revenue-making opportunity for developers and a great way of reaching a new app-hungry mass-market audience. Download the new Nokia SDK 2.0 for Java (Beta) and get developing! 

    Read the article

  • Shaping with shorewall complex shaper not work (or I don't understand principle of operation)

    - by strangeman
    I have router (Debian 6) with 2 network interfaces (and 1 virtual tun interface): eth0 - localnet, 192.168.1.0/24, router ip is 192.168.1.1 eth1 - internet tun0 - openvpn to central office. openvpn network - 10.1.0.0/24, central office network - 192.168.0.0/24 I need shape all traffic, which moves 192.168.1.0/24-192.168.0.1:6666 and 192.168.1.0/24<-192.168.0.1:6666, and restrict its speed to 200kbit. Now, I have this configuration, but its not work: tcdevices (set up interface parameters) #INTERFACE IN-BANDWITH OUT-BANDWIDTH eth0 100mbit 100mbit #LAST LINE -- ADD YOUR ENTRIES BEFORE THIS ONE -- DO NOT REMOVE tcrules (mark all traffic, which move on 6666 port) #MARK SOURCE DEST PROTO PORT(S) 1 0.0.0.0/0 0.0.0.0/0 tcp 6666 #LAST LINE -- ADD YOUR ENTRIES BEFORE THIS ONE -- DO NOT REMOVE tcclasses (shape all marked traffic) #INTERFACE MARK RATE CEIL PRIORITY OPTIONS eth0 1 200kbit 200kbit 2 eth0 255 9*full/10 full 1 default #LAST LINE -- ADD YOUR ENTRIES BEFORE THIS ONE -- DO NOT REMOVE Where is my mistake?

    Read the article

  • TrueCrypt - "Warning! Password locked: Fixed disk0" error message on boot

    - by Tibi
    TrueCrypt - "Warning! Password locked: Fixed disk0" error message on boot. When i start my laptop (Acer TravelMate 2410). after the starting memory check, the screen goes full black, and a message appears for about 3 seconds: Warning! Password locked: Fixed disk0 and after that, disappears, and next message comes out: Operating System Not Found and all stops here. Windows Xp was installed on it, before this came. TrueCrypt cd (witch was made during the process of full encryption) is not working, not in restoring MBR, no even in decrypting my drive - completely useless. Note: I detected some short of boot sector errors (i dont know the amount) on my drive before this happened. Please, i would greatfully thank every comment, or suggestion, because my computer is unusable now. The HDD is a Samsung HDD, 160Gb. Other preferences: Acer TravelMate 2410 Notebook, 2 Gb RAM, 1500 Mhz Intel Celeron M processor. Regards

    Read the article

  • Raid1+0: create stripe over two /dev/mdx on partition or not?

    - by Chris
    Given that I haven't found a way to define how a Raid10 is created with mdadm, i went the Raid1+0 solution. How to display/define Mirror/Stripping pairs with mdadm mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/sda1 /dev/sdf1 mdadm --create /dev/md1 --level=1 --raid-devices=2 /dev/sdg1 /dev/sdh1 mdadm --create /dev/md10 --level=0 --raid-devices=2 /dev/md0 /dev/md1 My question is about the stripe. For the mirror I create a primary partition over the full HD and set partition type to FD. So, should I do the same for the Stripe? Create partition on /dev/md0 and /dev/md1 (primary over full 'HDD', set partition type correctly) and then do the stripe on the partition? Is there a correct way here or are there any advantages/disadvantages to a solution? Thank you

    Read the article

  • Access Control issue

    - by user160605
    Ok this is stumping me mainly because of the lack of experience I have with access control. I have two folders I need to keep away from users. Payroll and Banking. I went into security and took away all the users. I made a new group called access granted and added it to both folders. I then gave full control to the group. I then added a few days to this group. I tested with partial success. I can only get into some folders and subfolders/files. I made sure I clicked on the option for all subfolders. This is my layout C:(folder) -- permissions granted to admin,access (full control) when I look at the problem files/folders no one has any permissions I don't even see the group or admin. what am I doing wrong. Thanks

    Read the article

  • A Myriad of Options

    - by Mark Hesse
    I am currently working with a customer that is close to outgrowing their Exadata X2-2 half rack in both compute and storage capacity.  The platform is used for one of their larger data warehouse applications and the move to Exadata almost two years ago has been a resounding success, forcing them to grow the platform sooner than anticipated. At a recent planning meeting, we started looking at the options for expansion and have developed five alternatives, all of which meet or exceed their growth requirements, yet have different pros and cons in terms of the impact to their production and test environments. The options include an in-rack upgrade to a full rack of Exadata using the recently released X3-2 platform (an option that even applies to an older V2 rack), multi-rack cabling the existing X2-2 to another full rack or half rack X2-2 (and utilizing both compute and storage capacity in the other rack), or simply adding a new X3-2 half rack (and taking advantage of the added compute and flash performance in the X3-2). While the decision is yet to be made, it had me thinking that one of the benefits of Exadata over a traditional database deployment is that when the time comes to expand the platform, there are a myriad of options.

    Read the article

  • how to publish c# project online

    - by hero
    i have done a simple c# website that have a lot of pics (3000+). i want to publish the full website online. all i know is that i have to first buy a domain name, and then buy some space on a webhosting server. could anybody guide me? how much does a domain name usually cost? and also how should i upload the website on a hosting server? i mean should i upload the full code?

    Read the article

  • How to makesure VM is in Para virtualization mode on XEN?

    - by ananthan
    I am having a server running XEN,with ubuntu 12.04 as Domain 0. Intel VT is turned on by default and i dont want to run any Windows OS as VM. So 1. how can i makesure that all the created VM will be in paravirtualized mode even with VT enabled? I have heard that in Full Virtualization hypervisor needs to work hard for emulating all the underlying hardware,which may reduce performance for too much i/o specific applications when compared to para mode. 2.Since i am running only Linux VMs do i really need to enable VT support? 3.Can i be able to run Linux VM in para mode with VT enabled? 4.Will simply turning on VT support changes virtualization from para to full virtualization?? 5.Will there be any performance improvement for VM running Linux OS if VT is enabled?

    Read the article

  • Thunderbird: "Could not initialize the application's security component" [closed]

    - by user unknown
    In Thunderbird, on startup, I get the error message: "Could not initialize the application's security component" The message continues to check permissions of the profile, and free disk space. df -h shows, that I have 19G free disk space. find . -not -perm -644 -not -perm -600 -ls shows: No file without rw-permissions for me. Before the error occured, thunderbird worked well. But I changed my main mail-account. I had two, let's call them A and B, and used mainly A, but now I wanted to deaktivate it, and receive and send automatically via the second. I Had problems moving the filters from inbox A to inbox B (missing copy-functionality). In the web, I found (mollazine) hints, to move key3.db, cert8.db and secmode.db out of the way, but it didn't work for me. Another hint was to uninstall Quickcam(?. sic!), but I don't have Quickcam. A third to recreate the profile, but I have subdirectories, filters, addressbook, groups - mails back to the year 2003. I don't want to risk the loss of data. The whole errormessage is: Could not initialize the application's security component. The most likely cause is problems with files in your application's profile directory. Please check that this directory has no read/write restrictions and your hard disk is not full or close to full. It is recommended that you exit the application and fix the problem. If you continue to use this session, you might see incorrect application behaviour when accessing security features. When I open the error-console, it is empty.

    Read the article

  • Separate 2 networks with 1 Windows Server

    - by SamuGG
    The situation is: I have 1 router 192.168.1.1, 1 switch, 1 windows server and a basic LAN of devices accessing it. I need to split into 2 separate LANs with full Internet access each, but isolated from each other. Given that, the server is a Windows Server 2008 R2 with 2 NICs: NIC1: 192.168.1.2 NIC2: 192.168.2.2 The router has no dhcp configuration. Please, can anyone explain gracefully, step by step, what do I need to do? What would be the 2 NICs full configuration? What services do I need to install? I don't want devices on either network to see devices on the other network, they must be completely separate. I guess I'm missing the routing procedure step, but I have no idea how is that done. For example: tell the server that devices with gateway 192.168.2.2 must send traffic for internet to 192.168.1.1 router. Thanks in advance.

    Read the article

  • Why do I see different TCP behaviour between IIS and FTP server applications on Windows 2003?

    - by rupello
    I am comparing Wireshark traces of a 10MB file download file from: the FileZilla FTP server and IIS (using HTTP) on the same Windows 2003 server. The FTP download performs faster and the trace shows the server behaving as expected, sending more data to the client with every ACK received: Link to full-size image The HTTP server trace shows a more bursty pattern. The timing of the send bursts are sometimes unrelated to any ACKs received from the client (circled in red): Link to full-size image Anyone have a suggestion as to why IIS traffic is having like this? Update: We have tried modifying the http.sys registry settings (setting MaxBytesPerSend to 256k and MaxBufferedSendBytes to 64k as recommended). Changing MaxBytesPerSend does seem to improve performance by increasing the amount of in-flight data , but we still see the same bursty pattern.

    Read the article

  • Good resources for learning modern OpenGL (3.0 or later)?

    - by MatterGoal
    I stumble upon the search of a good resource to start with OpenGL (3.0 or later) . Well, I found a lot of books but none of them can be considered a good resource! Here two examples: OpenGL Programming Guide (7th edition) http://www.amazon.com/exec/obidos/ASIN/0321552628/khongrou-20 This is FULL of deprecated material! Almost every chapters begin with a note about that. OpenGL Superbible (5th Edition) http://www.amazon.com/exec/obidos/ASIN/0321712617/khongrou-20 This book uses a library created by the author to explain the main arguments, hiding what you want to learn! I don't want to learn how to use your library! I want to learn OpenGL! I hope that you understand this is not the same question like "hey I'm not able to use Google... tell me how to learn OpenGL". I've just finished a full and deep search but I can't find a good and complete resource to learn the "new" OpenGL avoiding deprecated topics. Can someone heading me in the right direction? I know C++ and I have 10 years of experience in development... where I can find a good resource?! I want to spend time on it and I want to learn deeply. (please feel free to edit my question, my English is terrible!)

    Read the article

  • OS X Leopard (10.5) Server -- Unwanted Emails

    - by David
    Our OS X Leopard (10.5) server is sending out an email EVERY DAY for a Disk Full Notification on an external HDD we use for Time Machine backups (which manages it's own disk space, so the disk full notifications are useless). In the Server Admin app, under Settings Notifications, there's this: which is clearly disabled. The email header and message: http://pastebin.com/V5PZ3Phk I've been told to check the mail.log, but it's mostly empty (except for a few logs in 2011 saying "Postfix mail system is not running". I've also been told to check the crontabs, but I'm not sure how to do that on OS X (or any OS for that matter). Can someone explain how to do this? Also, if there's any other suggestions on places/things/etc to look at/for, my ears are all open!

    Read the article

  • Managing multiple ssh keys

    - by Mathijs Kwik
    I have a lot of ssh keys, they are all passphrase protected and managed by ssh-agent. As a result of this, I am now getting "Too many authentication failures" on some connections. As has been explained on this site before, this is because ssh will try all keys the agent throws at it. The proposed solution is to use IdentitiesOnly in the config, together with an IdentityFile. While this indeed stops offering wrong keys, it seems it completely disables the agent in full, so now I have to type the passphrase on every connection. I could not find clear info about this. Does IdentitiesOnly just disable getting keys from ssh-agent in full? Or should it just block out the keys that aren't mentioned? Thanks, Mathijs # here's my config ~% cat .ssh/config Host bluemote HostName some.host.com IdentitiesOnly yes IdentityFile /home/mathijs/.ssh/keys/bluebook_ecdsa # I had the key loaded into the agent, shown here ~% ssh-add -L ecdsa-sha2-nistp521 SOME_LONG_BASE64_NUMBER== /home/mathijs/.ssh/keys/bluebook_ecdsa # but it doesn't seem to get used ~% ssh bluemote Enter passphrase for key '/home/mathijs/.ssh/keys/bluebook_ecdsa':

    Read the article

  • Virtualise Excel in a browser

    - by Macros
    Is it possible to give users access to a virtualised instance of Excel - I don't want to give them access to a full OS (although this will clearly be running in the background, all they can access is Excel - they don't even see any other screens)? Secondly, if it is possible, is it possible to do within a browser? Edit I am building a system which is designed to test candidates skills in Excel and for this reason needs to use the full desktop version and not a web app. I don't want to have to ensure Excel is installed on the client machine as there will be issues around differing versions and security as the workbook(s) that are used in the test use VBA extensively to customise and mark the exercises. Ideally my web app would be able to open a session to the server which then just puts the user into an instance of Excel without ever seeing a desktop. I would also need to be able to pass in command line parameters in order to define which workbook to open and also pass in a unique token to identify the user

    Read the article

  • Shortcut with arguments in Debian

    - by Duncan
    I have a volume on a debian server which contains a large number of images at full resolution in various folders. What I'd like to do is have a separate sort of browse proxy folder which contains lower quality browse copies of these to enable users to access them for viewing over lower speed dial in accounts. I'd ideally like these to be created on the fly using ImageMagick so there isnt the need to store the large number of browse copies full time and worry about keeping them up to date etc The way I'd invisaged this happening is the browse proxy folder containing a duplicate file and folder structure but with symlinks pointing to a script to transform them with the file path as an argument. Except I know this isnt possible with symlinks so am wondering if there's another way of doing this on linux. On windows shortcuts can take arguments and I'm wondering how to do the same on a Linux platform? (or perhaps I'm going about this the wrong way?)

    Read the article

  • Backup restore issue

    - by rrahman_bd
    I have a windows server 2008 with exchange database full backup. Now for testing purpose i want to restore that full server to a VM. I have copied the whole backup to VM01 and took it to Private Network. And now i want to take backup from VM01 and restore it to VM02. Both are at private network. I was able to find VM02 test backup by searching in VM1. But the copyed restore file is not showing in the window !!! Is there any policy so that i can not restore except from the original location?

    Read the article

< Previous Page | 82 83 84 85 86 87 88 89 90 91 92 93  | Next Page >