Search Results

Search found 7154 results on 287 pages for 'networking'.

Page 86/287 | < Previous Page | 82 83 84 85 86 87 88 89 90 91 92 93  | Next Page >

  • Why can I not access the internet when Windows 7 finds no issue with the ethernet connection and the network can see my device?

    - by WannabeCoder
    So I just moved from a house to an apartment. In the house and the apartment I had Uverse set up - and in both I had my desktop connected via a ~40 foot long cat5 cable. However, upon moving to the apartment I found that my ethernet connection no longer provides internet. This would seem like a mundane problem if not for: The router can see the computer on the network Windows 7 (the desktop's OS) detects no problems with the ethernet connection. Connections over the internet (i.e. browser windows, Pandora, etc.) do not immediately fail. Instead they load for 2 minutes and then finally give up. Devices connected over the Wifi (PS4, Laptop) access the internet just fine While removing the cat5 cable from my house, I accidentally damaged the locking tab but managed to bend it back into the appropriate position. I would suspect that a bad cat5 cable might be to blame if not for the above issues (thought I've heard bad cat5 cables cause the most nonsensical problems) and the fact that I tested the cat5 cable by having it share internet between my laptop (working internet) to my desktop and it functioned just fine and provided the desktop with internet. My ipconfig /all successfully finds a default gateway, DHCP server, and DNS server. What could possibly be causing the problem?

    Read the article

  • Wi-Fi performance in Windows 8 RP on a MacBook Air (mid 2011)

    - by Steven Lu
    I was able to install the Boot Camp Windows software using the executable that it provided, and there are no unrecognized or unknown devices in Device Manager. Wi-Fi works but it seems to be limited to an extremely slow 1.5Mbits. Network Center reports an 802.11n connection (at 65Mbps usually) but transfers never reach above about 200kB/s. Being limited to 1/20th of the connection speed of my internet service is quite frustrating. Does anybody experience the same issue? I have been trying to identify the Broadcom Wi-Fi chipset and a driver that I could try to upgrade to but I have made very little progress on Google on this front.

    Read the article

  • Connecting to Aerohive APs from Laptops running Win. 7 using authentication from a Windows 2008 domain server

    - by user264116
    I have deployed a wireless network using Aerohive access points. 2 of them are set up as radius servers. I want my users to be able to use the same user name and password they use when they log onto our domain. They are able to do this from android devices or computers running Windows 8. It will not work on Windows 7 machines. How do I remedy this situation, keeping in mind that the machines are personal machines not company owned and I will have no way to change their hardware or software.

    Read the article

  • Mac OS X: network disabled because security breach

    - by fireeyedboy
    Dear all, I just recieved a message on my Mac OS X system telling me (loosely translated from Dutch): "The network has been temporarily disabled because the network's security was breached." (It's a wireless WPA2-PSK secured network BTW) I looked in the logs of my router (a Zyxel P-2602HW-D1A) only to see a few (outbound) "syn flood TCP ATTACK" logs, but those were from like a week ago, other than that nothing. What tools on Mac OS X do I have to analyse this security breach occurence? Are there some security logs on Mac OS X that I can inspect? What other measurements should I take? And how serious should I take this warning from Mac OS X? System: Macbook Pro Intel Core 2 Duo 2.2 Ghz OS: Mac OS X 10.5.8 Network: wireless WPA2-PSK Relevant software: Parallels Desktop with Windows XP (was open, but stopped at the time) Other systems on my network: Windows XP SP3 desktop (was running at the time) If you need any more info, don't hestitate to ask. Thanks in advance.

    Read the article

  • how I can Specifying tcpreplay speed

    - by herzl shemuelian
    I am tring to Specify tcpreplay speed but I can't do it this is my detail of test: $tcpreplay -V tcpreplay version: 3.4.4 (build 2450) 1)$ tcpreplay -i %0 -p 100 -L 500 _udp_only.pcap Actual: 500 packets (42247 bytes) sent in 5.05 seconds.Rated: 8365.7 bps, 0.06 Mbps, 99.01 pps s 2)$ tcpreplay -i %0 -p 1000 -L 5000 _udp_only.pcap Actual: 5000 packets (427710 bytes) sent in 5.19 seconds. Rated: 82410.4 bps, 0.63 Mbps, 963.39 pps //here is problem I stay in 966.00 pps 3)$ tcpreplay -i %0 -p 10000 -L 50000 _udp_only.pcap Actual: 50000 packets (4322559 bytes) sent in 51.76 seconds.Rated: 83511.6 bps, 0.64 Mbps, 966.00 pps I have same problem when I try to Specify --mbps for 8600 packets 86 byte avg for each packet -M0.086 -L 860 ---- Rated: 10812.9 bps, 0.08 Mbps, 127.22 pps -M0.86 -L 860 ---- Rated: 83062.5 bps, 0.63 Mbps, 977.27 pps -M0.86 -L 8600 ---- Rated: 82554.9 bps, 0.63 Mbps, 965.21 pps why and how I can to Specify speed? I use OS windows7

    Read the article

  • Is there any reason to subnet a home network?

    - by Will
    For networks I understand we set a netmask on each computer to let it know what IPs it can talk to without going through the router - IPs on the same subnet can talk directly to each other and do not have to go through a router/switch. However, in today's home networks (and I suspect corporate networks as well) every computer is connected to a router/switch (at the low cost of today's hardware I doubt there it much of a market for wired repeaters/hubs). This seems to obviate the need for a subnet mask and subnetting. Considering that in most modern home architectures every computer goes through the router, even to talk to computers on the same network, is there any reason for me to subnet a home network?

    Read the article

  • Windows 7 - system error 5 problem

    - by Ian
    My wife has just had a new computer for Christmas (with an upgrade from VISTA to Windows 7), and has joined the home network. We are using a mix of WindowsXP and Ubuntu boxes linked via a switch. We are all in the same workgroup. (No domain). Internet access, DHCP, and DNS server is an SME server that thinks it is domain controller (although we are not using a domain). I need to run a script to back up my wife's machine (venus). In the past the script creates a share on a machine with lots of space (leda), and then executes the line. PSEXEC \\venus -u admin -p adminpassword -c -f d:\Progs\snapshot.exe C: \\leda\Venus\C-drive.SNA With the wife's old XP machine, this would run the sysinternals utility, copy shapshot,exe to her machine and run it, which would then back up her C: drive to the share on leda. I cannot get this to work with Windows 7, nor can I link through to the C$ share on her machine. This gives me a permissions error (system error 5). The admin account is a full admin account. And yes - I do know the password. The ordinary shares on her machine work fine! I guess I'm missing something that Microsoft have built into Windows 7 - but what? The machine is running Windows 7 business, with windows firewall, AVG anti virus, and all the crap-ware you get with a new PC removed. Thanks

    Read the article

  • Using Juniper EX3300 as a router

    - by Richard Whitman
    So I have a Juniper EX3300 Switch. One of its uplink ports (ge-0/1/0) is connected to my ISP's router. ISP router's port address is xx.xx.xx.109. My switch's IP address is xx.xx.xx.110. From the switch, I can ping to xx.xx.xx.109 and any other IP in the world. I mean its connected to the Internet. I connected the port eth0 of a computer (running Ubuntu) to the port ge-0/0/0 of the switch (which in the same VLAN as ge-0/1/0). I configured the port eth0 as follows: iface eth0 inet static address yy.yy.yy.208 netmask 255.255.255.240 gateway xx.xx.xx.110 yy.yy.yy.208 is assigned to me by the ISP. So, now I can ping to the switch (xx.xx.xx.110) from this computer. But I can not ping to either xx.xx.xx.109 (ISP router) or any other IP. I want this computer to be connected to the Internet. What am I doing wrong? Here are some of the configurations on my switch: interfaces { ge-0/0/0 { unit 0 { family ethernet-switching; } } . . . ge-0/1/0 { ether-options { no-auto-negotiation; link-mode full-duplex; speed { 1g; } } unit 0 { family ethernet-switching { port-mode access; } } } . . . vlan { unit 0 { family inet { address 10.0.1.1/24; } } unit 1 { family inet { address xx.xx.xx.110/30; } } } } . . . routing-options { static { route 0.0.0.0/0 { next-hop xx.xx.xx.109; retain; } } } vlans { Cogent { vlan-id 3; interface { ge-0/1/0.0; ge-0/0/0.0; ge-0/0/1.0; ge-0/0/2.0; ge-0/0/3.0; } l3-interface vlan.1; } TFLan { vlan-id 2; interface { ge-0/0/5.0; ge-0/0/6.0; ge-0/0/7.0; ge-0/0/8.0; ge-0/0/9.0; ge-0/0/10.0; ge-0/0/11.0; ge-0/0/12.0; ge-0/0/13.0; ge-0/0/14.0; ge-0/0/15.0; ge-0/0/16.0; ge-0/0/17.0; ge-0/0/18.0; ge-0/0/19.0; ge-0/0/20.0; ge-0/0/21.0; ge-0/0/22.0; ge-0/0/23.0; ge-0/0/4.0; } l3-interface vlan.0; } }

    Read the article

  • internet disconnects

    - by Smokezzaj
    Internet disconnects and reconnects, computer is in a peer to peer workstation with two other computers XP o/s. Only one computer has this problem the other two don't disconnect. Computer's connect to switch no router is being used. Ipconfig shows a DHCP connection, local area connection status shows packets being sent out but packets are not being received or being received at a extremely slow rate. Tried Winstock tool, reinstalling network card driver, restored to previous date, checked ethernet cable and release/renew IP.

    Read the article

  • NIC interface names in /proc/interrupts

    - by Gallus
    When I look at /proc/interrupts: $ cat /proc/interrupts CPU0 CPU1 (...) 12: 4 0 IO-APIC-edge i8042 14: 145 65310875 IO-APIC-edge ide0 50: 0 0 IO-APIC-level uhci_hcd:usb5, Intel ICH7 58: 5388 7983508 IO-APIC-level libata 169: 812427252 1236572641 IO-APIC-level skge, eth1 217: 6 0 IO-APIC-level ehci_hcd:usb1, uhci_hcd:usb2 225: 0 0 IO-APIC-level uhci_hcd:usb3 233: 60 3108720778 IO-APIC-level uhci_hcd:usb4, skge I can see two skge and one eth1 entries. All of them are the network cards. Because of the general name "skge" (which is the name of the network driver of the card) I can't easily reocognize, which NIC occupies which interrupt. How to make linux use more descriptive names in the entries? Or: Is there any alternative way to obtain INT information instead of /proc/interrupt? My final goal is to manipulate smp_affinities of the NICs.

    Read the article

  • DrayTek Vigor 2920(n): VPN with VLAN restrictions?

    - by Dirk
    Hi, I'm currently installing a DrayTek Vigor 2920n router in a new office. This router is to be used for 2 seperate companies. For one of these companies, the router has a LAN-2-LAN (VPN) connection to a datacenter configured. The other company should not be able to access this other (VPN-)network. I'm aware of the capability of this router to have VLAN's, but I cannot figure out how to configure the VPN-connection to only be accessible for VLAN0 and not for VLAN1. I know I can also add another router to physically split both networks, but we bought the DrayTek with the idea that it could easily have the VPN-connection available for VLAN0 and not for VLAN1. VLAN1 can easily be in another subnet, that's fine, although, I don't know how to configure that on this DrayTek. Can anyone point me in the right direction? Thanks in advance, Dirk

    Read the article

  • Default route not on LAN

    - by jarmund
    I have a network that in principle looks like this: H1---\ /----Inet1 H2---->---GW1---< H3---/ \----GW2-----Inet2 H1 and H2 = Hosts that need access to internet with GW1 Inet1 = Internet link over 3G connection Inet2 = 5GHz link to Internet (not always up) GW1 = Works as a router, automatically picking the "best" connection between Inet1 and Inet2 (the latter via GW2). GW2 = 5GHz wifi router And here's the problem: H3 only needs internet access when Inet2 is up. What i was thinking of doing was a routing table that looks like this: route to GW2 via GW1 default route is via GW2 I first set the route to GW2 via GW1 without a problem. But when i try route add default gw 1.2.3.4 (1.2.3.4 being the IP of GW2), it complains "SIOCADDRT: No such device" Is the problem that the default gw i'm trying to set is not reachable directly? Is there a different approach that would allow me to achieve this? An alternative (and hypothetical) approach: Since H3 will be using a static IP, is it possible to do some magic with iptables on GW1 to forward any packets from H3 to GW3, thereby "tricking" H3 into using GW2 as its default router?

    Read the article

  • How can I connect DLNA devices through NAT?

    - by Bob
    I have a Windows 7 PC running Serviio as a DLNA server. I have a Samsung I9100G running Skifta as a DLNA renderer (client). My network topology: At the moment, I can connect and watch my videos fine if the phone is on router #2. The server is on a wired network with #2. Router #1 is 192.168.1.1, router #2 is 192.168.2.1 (192.168.1.2) and router #3 is 192.168.3.1 (192.168.1.3). In other words, each router has its own subnet, using NAT - their "modem" port is connected with a "LAN" port on the modem/router 1. What I want to do is be able to connect to the DLNA server if the renderer is connected to router #1/#3 - #1 is on the WAN side of #2, while #3 is even further separated. I'll settle for just #1 working, though. Normally, I would just forward the appropriate ports, and everything would work fine. However, (apparently) DLNA uses UPnP, which I am unfamiliar with. I tried enabling UPnP on router #2, but that did not seem not change anything. It's a Belkin F5D7230-4 6000 - there's reported issues with UPnP on F5D7230-4 7000. UPnP is already enabled on router #1 - a Billion BiPAC 7700N. I've also tried the built in DLNA renderer/server/controller on my phone, Samsung AllShare. It can see the server on router #2 and browse files, but has issues playing or downloading them. It also can't see the server on the other two networks. I'm currently using Skifta/s "local" mode. "Remote" mode requires an account, which I don't really want to create if not necessary. Is it possible too do what I'm trying to do? If no, are there workarounds? If yes, how do I do it? Is my server the issue? The renderer (client)? The router(s)? My method? I can change just about anything except the routers.

    Read the article

  • ADSL with RFC 2684 Bridging

    - by Axel Isouard
    My new ADSL line is now enabled, I can finally use my Netgear DM111Pv2 to use to the Internet. My ISP has told me a big surprise : I don't need to use a login and a password to connect to the Internet, then I must use the RFC 2684 bridging mode. It works pretty fine on the ADSL modem's side, but I've spent one night trying to figure out how to connect to the Internet through this modem. I only have a Fonera 2.0n and a computer running Gentoo Linux. I've been trying to use the br2684ctl utility with brctl on my Gentoo, first I've configured my kernel in that way : CONFIG_PPP=y CONFIG_PPP_BSDCOMP=y CONFIG_PPP_DEFLATE=y # CONFIG_PPP_FILTER is not set CONFIG_PPP_MPPE=y # CONFIG_PPP_MULTILINK is not set CONFIG_PPPOATM=y CONFIG_PPPOE=y CONFIG_PPP_ASYNC=y CONFIG_PPP_SYNC_TTY=y [...] CONFIG_ATM=y CONFIG_ATM_CLIP=y CONFIG_ATM_CLIP_NO_ICMP=y CONFIG_ATM_LANE=y CONFIG_ATM_MPOA=y CONFIG_ATM_BR2684=y # CONFIG_ATM_BR2684_IPFILTER is not set And I still get these messages : cirus nais # br2684ctl -b -c 0 -e 0 -a 8.35 br2684ctl[8041]: Interface "nas0" created sucessfully br2684ctl[8041]: Communicating over ATM 0.8.35, encapsulation: LLC br2684ctl[8041]: Fatal: failed to connect on socket; No such device The brctl utility keeps telling me "Invalid argument" each time I try to add the nas0 interface into my bridge, I'm honestly hoping I'm doing wrong. I've been following this README carefully and this tutorial on setting up a PPPoE connection with Gentoo, but the PPPoE interface just tries to start, and nothing special related to PPP happens, I can't see the interface when I do ifconfig. So, I'm asking you if there's something huge I've been missing since the beginning ! Maybe I should wait to buy a new router fully supporting the RFC2684 bridging mode, but I'm more interested in setting up this mode on my Fonera 2.0n and even my Raspberry Pi !

    Read the article

  • setting up a WGR614v7 behind a linux box

    - by commodore fancypants
    Here's the setup, I have an openSUSE box with 2 NICs, one goes to my home network router, the other has DHCP running and it attached to a wireless router. I'm trying to get this setup to work before I switch to the linux box as my home network router. My DHCP will offer the wireless router (a WGR614v7) an address, but anything that connects to the wireless router ends up with a APIPA address. I have all the firewalls on the wireless network turned off as well as the wireless router's own DHCP. The linux box isn't offering addresses to anything past the wireless router. Is this a problem with the router or my DHCP setup? For testing purposes, I have both NICs set in the internal zone and I've tried wireless and wired connections to the WGR614v7 both to no avail.

    Read the article

  • Route packets from one VPN to another

    - by Mike
    I have two OpenVPN servers (10.8.0.0 and 10.9.0.0) set up on my OpenSUSE server. Within one network, each computer is visible to any other one, but I'd like to make it so that computers are visible across networks. I'd like to route the packets like this: when a user (say 10.8.0.6) pings an address on the other VPN (10.9.0.6), the packets are routed to the 10.9.0.1 and then to the appropriate computer in this VPN. How do I achieve this using iptables or a different tool? I tried the commands at the end of this section with no avail.

    Read the article

  • Can't access server on LAN new Router

    - by RMDan
    Earlier this week my roommates decided to change the router we are using for our home network. On the old router I had no problems accessing a laptop running Mint Linux over the network(SSH, FTP, and Shared Folders). However I am now not able to connect. I have verified the IP address of my Linux machine has not changed and I have no problems connecting to our NAS(WDMYCLOUD). The new router is a D-Link DIR-868L. PuTTY is giving me a Timed Out error(was giving me a EHOSTUNREACH before). Running Windows 8.1 the connecting laptop, but tried connecting using my phone via SSH did not work either. More information: Can ping the Linux machine from the router but not my computer. Pinging 192.168.0.111 with 32 bytes of data: Reply from 192.168.0.102: Destination host unreachable. Reply from 192.168.0.102: Destination host unreachable. Reply from 192.168.0.102: Destination host unreachable. Reply from 192.168.0.102: Destination host unreachable. Ping statistics for 192.168.0.111: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

    Read the article

  • Remotely push DNS server to client via OpenVPN

    - by wishi
    Hi! When I try to push a DNS server via the OpenVPN server-config I don't get that server to be the first DNS server on the connected client system. It ends up being specified as an alternative DNS server. push "dhcp-option DNS 89.238.75.146" # DNS-Server 1 (local djbdns) To overcome certain network restrictions, if they're at place, I use 443 TCP. - That means that my DNS queries are sent via TCP (if I manually reconfigure the DNS server), which doesn't scale very well from a performance perspective. Are there any kewl solutions for that? Marius

    Read the article

  • What's the likely culprit in email delay?

    - by Kiki
    If anyone can shed light or point me to a tutorial, I'd appreciate it. We are a tiny company and have experienced occasional delays in receiving email sent between staff members. We are in separate cities but all in the same state; our webhost/email ISP is across the country from us. If it matters, we're on Macs and most of use Entourage. Our email configurations are POP server: companyname.com and SMTP: smtp.companyname.com (When we used our DSL providers for SMTP we had unreliable service) Our ISP says they're not seeing delays related to their equipment and the problem is elsewhere in the network. A co-worker believes that the delays are with the ISP. Is there a good way to figure this out?

    Read the article

  • Windows 7 and Vista Home Networked-Unable to login from Vista to Windows 7

    - by Lynn
    I set up both Vista and Windows 7 on the same workgroup. I can view Windows 7 from Vista and vice versa. I can login into Vista from Windows 7. I am unable to login to Windows 7 from Vista. When I enter the Windows 7 User name and Password on Vista, the following information appears: Logon unsuccessful: Windows is unable to log you on. Be sure that your user name and password are correct. Both are correct. Do you have any idea how I can resolve this logon issue? Thank you, Lynn

    Read the article

  • Rename a Network Printer win Win 7

    - by Alex
    Seems this is a common question but the answers regularly miss the point. I have a server. Server has some printers connected. Server has all drivers for x32 & x64 OS PLUS ALL DEFAULTS set. Server also manages print queue. I have many workstations, all need to use the printers. All NEED to have drivers print queue and DEFAULTS propagated from server. Now.... When I add the printers on the workstations, I get: "ABC Printer on SERVER123" I need something less long - just "ABC Printer" So how? Tip: Please don't show me how to change the name of your locally installed printer. I know how to do this - I am particularly interested in shared printers that look like "ABC Printer on SERVER123" Tip: Installing the driver with a local port wont cut it because then I loose the server propagated defaults, the driver updates and I need to run around with driver disks/confuse trembling users with hard things like choosing drivers. I am happy for a hack if there is no official way to do this in the group policy.... I tried looking in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Printers on the workstation machines but those are only local printers :( I can see the network printer details on the workstations here: HKEY_USERS[Some GUID]\Printers\Connections But there is nothing obvious like a description string... Can anyone help with this?

    Read the article

  • Cannot establish a network connect to VMWare Fusion VM

    - by twolfe18
    I am running Snow Leopard 10.6.2 (not the server edition) with VMWare Fusion 3.0.0 and I trying to get my Ubuntu 9.10 x86_64 VM working. I am using a bridged connection, and I have an internet connection FROM the Ubuntu VM (I can download updates, ping websites, etc), but I cannot connect TO the Ubuntu box from any other device on my network. I am trying to get Mongrel up on the Ubuntu VM for some Rails stuff, but it's not working. I know Mongrel/Rails is not the problem because if I start the server on the Ubuntu VM, background the process, and then wget the index page, it works. I just cannot connect to the site from another IP. I have tried using a static IP and a DHCP IP configuration on the Ubuntu VM, neither work (for incoming connections, both work for outwards). I have port scanned the Ubuntu VM, and it appears that all ports are closed. However, the Ubuntu VM does respond to pings. I noticed a similar question here: http://serverfault.com/questions/99757/setting-up-a-bridged-network-with-vmware-fusion, but no answer. Any ideas?

    Read the article

  • Should I remove all unmanged switches from my network?

    - by IMAbev
    I have a office network with approx 150 devices (computers/printers/ip phones). Almost all of the end point devices have straight run Cat5e from my Hp switches directly to the device. IP phones for each end user sit between the hp switch and computer. (hp switch - in to phone out of phone in to computer) While I have gotten rid of most of them, I still have a couple linksys unmanaged switches that split off to 2 or more devices. I have heard various reasons for removing these switches but not entirely sure if it actually degrades the network. I agree that eliminating these switches certainly cleans up the network from a management standpoint. Are these unmanaged switches bad for my network? Is there a clear advantage to having 'home run' cable runs to each of my end point devices?

    Read the article

  • Wicd not playing well with networks that utilize network access control

    - by Sion
    Starting a couple months ago (might be able to find exact date if necessary) my installation of Wicd stopped being able to see wireless networks that use NAC (Network Access Control) such as Aruba networks. But if I shut down Wicd and start NetworkManager I can connect to said networks and log in to them depending on what the NAC requires. This is the current wicd package installed: net-misc/wicd-1.7.1_pre20111210-r1 This is how I manipulate the network manager running: su -c'/etc/init.d/wicd stop; /etc/init.d/NetworkManager start' What would cause this specific of a problem to occur?

    Read the article

< Previous Page | 82 83 84 85 86 87 88 89 90 91 92 93  | Next Page >