Search Results

Search found 2590 results on 104 pages for 'robert morning'.

Page 86/104 | < Previous Page | 82 83 84 85 86 87 88 89 90 91 92 93  | Next Page >

  • Why isn't my phone charging with some micro usb cables?

    - by Jacxel
    I ordered 3 microUSB cables over ebay. My phone was at about 50% battery and I wanted to use it as a hot spot for some browsing on my laptop, so I plugged it in, a charging icon appeared on the phone, my laptop showed it as a connected usb device and so I went about my business. About 30 minutes later I checked the phone and to my dismay saw 45% battery. But ahh, I thought, I have been putting the poor little thing under too much pressure, acting as a WiFi hotspot must drain the battery quicker than it can charge via usb, perhaps even using my laptops usb port wouldn't output enough power. Unscathed I continued on and when I was going to bed I plugged the usb cable into a mains adapter and switched everything battery consuming off and content, went to sleep. The next morning I was awoken by my phones alarm which got cut off unexpectedly. I attempted to unlock my phone which showed no more signs of life. Why isn't my phone charging with these new USB cables? For clarity: They transfer data with no problems The phone appears to be charging, showing all the signs and lights it normally would, the cable that came with the phone works as you would expect, so its not a fault with the phone, I think they slow the discharging of the phone, but I could be wrong. Are these just bad quality cables? Is there a way to fix this issue?

    Read the article

  • IP6 seems to be enabled - How do I configure it without interfering with IP4?

    - by Mister IT Guru
    I noticed that some of my Centos boxes have IP6 enabled, and seem to have addresses. I have no problem with this, but I would like to get a handle on it, and even connect to them using IP6. This would really help if for any reason DHCP has a hiccup. But I'm a bit lost as to where the configuration on my CentOS box is. (I am also on google researching this, but I like server fault! :) ) I am hoping that I would be able to log into this via the VPN because every now and then that DHCP device has a bad morning, and needs to be restarted. (I'm also looking into this issue, but someone else handles that, management separation gone mad!) It's a remote client, so it would be a lot easier for me to connect to these systems which seem to self configure, to use that as a pivot via ssh tunnels to get to other remote devices to continue to manage them, while out main route is fixed. I guess, my questions are How can I configure IP6 without interfering with IP4, and On CentOS, can I influence this auto configuration I seem to be seeing?

    Read the article

  • Why does Windows Firewall want to block Google Chrome today?

    - by hippietrail
    I've been using the same public Wi-Fi (staying in a guesthouse) for over a week now. But this morning for the first time I got this puzzling warning from Windows Firewall: Why does Windows Firewall want to block one of the world's most popular web browsers today after being fine with it for years, and being fine with it on this connection for a week? Could it hinge on the words, some features? If so could it be something like a rare or new feature of Chrome that uses a different HTTP port? And if so why doesn't the security alert tell me any more about it? Or could it be a known bug in Windows Firewall? Or perhaps a known virus etc attaching itself to Google Chrome? Or is there a chance it's related to "Other browser makers follow Google's lead, revoke rogue certificates"? I haven't restarted Chrome for days and have downloaded but not installed a Windows update from a few days ago. So I'm not sure what may have managed to change on my machine since yesterday.

    Read the article

  • Debian Server wont reboot from script

    - by Littlejon
    I have a script that is run to backup a server via Rsync, after that script is run I want the server to reboot. My script is run as root from the Crontab at 3am in the morning. #!/bin/bash HOST="email" RSYNC_OPTS="-a -v -v --progress --stats --delete" RSYNC_DEST="10.0.0.10::$HOST" BACKUP_LIST="/etc /home /root" TIMESTAMP="/timestamp-bkup-start.chk" TIMESTAMP2="/timestamp-bkup-stop.chk" touch $TIMESTAMP rsync $RSYNC_OPTS $TIMESTAMP $RSYNC_DEST for BACKUP_ITEM in $BACKUP_LIST; do rsync $RSYNC_OPTS $BACKUP_ITEM $RSYNC_DEST done /etc/init.d/zimbra stop sleep 60s rsync $RSYNC_OPTS /opt $RSYNC_DEST touch $TIMESTAMP2 rsync $RSYNC_OPTS $TIMESTAMP2 $RSYNC_DEST echo `date +%Y%m%d%H%M` >> /var/log/reset reboot # $# shows number of args passed # $1 to access first variable #if [ $# -eq 1 ]; then # if [ $1 = "withreboot" ]; then # echo "rebooting..."; # echo `date +%Y%m%d%H%M` >> /var/log/reset # /sbin/reboot # fi #fi I have tried using init 6 rather then reboot. I have tried /sbin/reboot. I also have another basic script that just echos to the reset log and runs reboot without issue. It is just with the script above the server wont restart. If anyone has any theories that would be great as I have run out of idea. Thanks, Jon

    Read the article

  • Time Machine is getting stuck at "Preparing to Back Up" and my Trash isn't emptying

    - by zarose
    I have encountered two separate problems, but I am putting them in the same question in case they are related. First, my Trash would not empty. It seems to be getting stuck on certain files, because I will reset my Macbook and some of the files will be deleted, and then if I remove a file or two at random, more can be deleted. Some of these files had strange characters in their names. I tried changing the names to single characters, but this did not help. Next, I attempted to backup my Macbook using Time Machine. I plugged in the HDD I've been using for this, but every time I try to start the backup, Time Machine gets stuck at "Preparing to Back Up". I definitely need to know how to fix the Time Machine problem, but I am curious how to solve the trash problem as well, and whether or not these problems are related. EDIT: Console.app logged the following this morning before I left on a trip. I did not bring the HDD with me. 6/5/12 7:41:28.312 AM com.apple.backupd: Starting standard backup 6/5/12 7:41:46.877 AM com.apple.backupd: Error -35 while resolving alias to backup target 6/5/12 7:41:58.368 AM com.apple.backupd: Backup failed with error: 19 6/5/12 7:59:08.999 AM com.apple.backupd: Starting standard backup 6/5/12 7:59:10.187 AM com.apple.backupd: Backing up to: /Volumes/Seagate 3TB Mac/Backups.backupdb 6/5/12 7:59:13.308 AM com.apple.backupd: Event store UUIDs don't match for volume: Macintosh HD 6/5/12 7:59:13.331 AM com.apple.backupd: Event store UUIDs don't match for volume: Blank 6/5/12 7:59:13.683 AM com.apple.backupd: Deep event scan at path:/ reason:must scan subdirs|new event db| 6/5/12 8:23:31.807 AM com.apple.backupd: Backup canceled. 6/5/12 8:23:33.373 AM com.apple.backupd: Stopping backup to allow backup destination disk to be unmounted or ejected. 6/5/12 9:51:21.572 PM com.apple.backupd: Starting standard backup 6/5/12 9:51:22.515 PM com.apple.backupd: Error -35 while resolving alias to backup target 6/5/12 9:51:32.741 PM com.apple.backupd: Backup failed with error: 19

    Read the article

  • Method to integrate Powershell scripts with non-Windows workflow?

    - by Matt Simmons
    I love the smell of new machines in the morning. I'm automating a machine creation workflow that involves several separate systems across my infrastructure, some of which involve 15 year old perl scripts on Solaris hosts, PXE Booting Linux systems, and Powershell on Windows Server 2008. I can script each of the individual parts, and integrating the Linux and Unix automation is fairly straightforward, but I'm at a loss as to how to reliably tie together the Powershell scripts to the rest of the processes. I would prefer if the process began on a Linux host, since I imagine that it will end up as a web application living on an Apache server, but if it needs to begin on Windows, I am hesitantly okay with that. I would ideally like something along the lines of psexec for Linux to run against Windows, but the answer in that direction appears to by Cygwin, and as much as I appreciate all of the hard work that they put in, it has never felt right, if you know what I mean. It's great for a desktop and gives a lot of functionality, but I feel like Windows servers should be treated like Windows servers and not bastardized Unix machines (which, incidentally, is my argument against OSX servers, too, and they're actually Unix). Anyway, I don't want to go with Cygwin unless that's the last and only option. So I guess what I'm asking is if there is a way to execute jobs on Windows machines from Linux. Without Cygwin. I'm open to ideas and suggestions, including "Look idiot, everyone uses Cygwin, so suck it up and deal with it". Thanks in advance!

    Read the article

  • Help trying to figure out why IIS7 is crashing / locking up / denying connections

    - by Pure.Krome
    Hi folks, I've got a pretty busy website that is running on a single web front end machine, on W2K8 + IIS7. Every now and then - eg. maybe monday at 3am or something, then a few days later .. some early morning time .. then nothing for 2 weeks ... etc - the website fails to respond to any client connections. ie. no one can connect to the website. I can remote desktop to the machine, etc no probs. I restart the app pool (the website is running in intergrated mode), still nothing. I try and get a crash dump of the process (it's around 600 mb maybe even more) ... that fails after about a min of trying (and i have plenty of HD space). The only way to fix this issue, is to manually stop the www service and then start it again. The stopping takes a while (a minute?) while starting is nearly instant. I'm at a loss to figure out what part of my code is causing this. At first, I thought it might be a stack overflow because of some error that might be going to the error page, which in turn errors .. rinse repeat boom. But i've had a look at the error page and it feels ok. So, I'm hoping someone might be able to help and say how I can correctly get a proper dump of the IIS process so i can then do some more autopsy on it. I would email Tess Ferrandez (the goddess of crash debuging) but I thought I'd try here before I spam her. Can anyone have any suggestions to how I can figure out how to start to debug this issue?

    Read the article

  • Three server processes consume no more than 50% of Dual Core CPU

    - by thor
    I have three processes running on Intel Core 2 Duo CPU. From watching output of 'top' and graphs of CPU load (drawn by MRTG, data collection via SNMP) I can see that CPU load is never more than 50%, and, most of the day, when those processes are busy CPU load has a ceiling at 50 %. I mean, CPU load grows up to 50% in the morning and stays there until late evening. My first thought was that only one core was used at 100% thus giving 50% of both CPUs. But, as there are three processes running and from 'top' I see that both cores are being loaded, so this is not the case. schedtool shows that CPU affinity for those three processes is at default, 0x03, allowing them to use both cores. If I force one process to one core (schedtool -a 0x01), and two others to second (schedtool -a 0x02), cumulative usage grows beyond 50%. Why three processes seem to consume only 50% of two cores? Why forcing them to different CPUs allows usage to grow higher? Any hints? P.S. Processes in question are Counter-Strike servers.

    Read the article

  • Emails not sending from outlook / OWA - Not even hitting the mail queue in exchange

    - by webnoob
    We are having an issue this morning where we can receive external emails but cannot send internal or external ones from Outlook or OWA. If I use: Send-MailMessage –From <[email protected]> –To <[email protected]> –Subject “Test #01”-Body “Just a test message.” –SMTPServer <Server-Name> –Credential <domain\user> the email is sent correctly which makes me think there is a connection issue with OWA and Outlook. However, outlook is reporting as Connected with exchange. I have checked the message tracking in exchange tools and emails sent via outlook and OWA do not appear. Nothing has changed on the server on the weekend so I don't really know where to start debugging this issue. We are using Windows SBS 2011. We only have one send connector which isn't using Smart Hosts and is set to use DNS MX records. Use external DNS is not checked and I can ping google.com etc so doesn't appear to be a DNS issue (plus the email sends from the console anyway). EDIT It appears that users using IMAP can send emails correctly, its only ones that rely on the normal exchange connection type that don't work. EDIT Emails from IMAP are hitting the email queue's where as emails from the normal exchange accounts aren't. EDIT It seems that some of the emails we tried to send yesterday sent at about 1am but now it won't work again..

    Read the article

  • Dell Vostro Desktop error

    - by goldenmean
    Faced a strange situation at work today. We have people sitting at a table on opposite sides, with power cables underneath the table. This morning when the person sitting opposite to me banged his feet on ground, it disturbed the power cable to my PC and it turned-off. So when I turned it on, it says, "No boot device found" Press F1 to setup or F5 to perform test... There was no physical impact/crash/fall of the desktop cabinet, which could have crashed/damaged the hard disk physically. EDIT: The OS is Windows 7 So I tried to recognize it in the Bios setup, but even there it could not find the SATA disk that is connected to this machine. So then I opened the cabinet, removed the power supply and plugged it back again. Tried to reboot, same error, "Boot device not found" It is not recognizing the hard disk. Any ideas about what might be wrong? Hard-disk crash, OS Crash(But it doesn't even go to the point of loading the disk after the initial Bios execution, so doubt this...) Any pointers about how I should proceed to troubleshoot/solve this error are welcome.

    Read the article

  • Offline productivity

    - by Frank Meulenaar
    On some days I'm commuting 2hs (oneway) in the train. I don't have any mobile internet nor is there always WiFi service in the train. Because of security reasons I can't do any work in the train so I'm trying to work on my geek time. I'm looking for general solutions on how to do this (I'm on FireFox/Windows but I don't think it matters) Email works perfectly with gmail offline. It syncs directly when online and remembers complicated stuff. So far I used the ScrapBook plugin to store an website. It works good, but I have to download my favorite news page every day again - I want it to sync as soon as possible. It would even be more awesome if I could click a page on my desktop and my laptop would sync as soon as it has the chance. (edit: maybe the autosave plugin for scrapbook can do this) Similarily, I use the Downloadhelper plugin to download youtube vids, but I'd like something that automatically downloads videos from a given channel. Any tips are welcome. So far my early morning schedule is: wake up, power on laptop, make coffee, power off laptop and leave within 10 minutes (enough time for GMail to sync) but I can imagine a system where my laptop stays on during the night (or boots before I wake (and makes me coffee :])).

    Read the article

  • Possible disk IO issue

    - by Tim Meers
    I've been trying to really figure out what my IOPS are on my DB server array and see if it's just too much. The array is four 72.6gb 15k rpm drives in RAID 5. To calculate IOPS for RAID 5 the following formula is used: (reads + (4 * Writes)) / Number of disks = total IOPS. The formula is from MSDN. I also want to calculate the Avg Queue Length but I'm not sure where they are getting the formula from, but i think it reads on that page as avg que length/number of disks = actual queue. To populate that formula I used the perfmon to gather the needed information. I came up with this, under normal production load: (873.982 + (4 * 28.999)) / 4 = 247.495. Also the disk queue lengh of 14.454/4 = 3.614. So to the question, am I wrong in thinking this array has a very high disk IO? Edit I got the chance to review it again this morning under normal/high load. This time with even bigger numbers and IOPS in excess of 600 for about 5 minutes then it died down again. But I also took a look at the Avg sec/Transfer, %Disk Time, and %Idle Time. These number were taken when the reads/writes per sec were only 332.997/17.999 respectively. %Disk Time: 219.436 %Idle Time: 0.300 Avg Disk Queue Length: 2.194 Avg Disk sec/Transfer: 0.006 Pages/sec: 2927.802 % Processor Time: 21.877 Edit (again) Looks like I have that issue solved. Thanks for the help. Also for a pretty slick parser I found this: http://pal.codeplex.com/ It works pretty well for breaking down the data into something usable.

    Read the article

  • SBS2011 Standard DNS suddenly not resolving some domains

    - by Matt
    Suddenly today I am unable to resolve common domains like serverfault.com, facebook.com; but other domains like google.com, cnn.com work fine. This is on a client machine (Win7 Pro) connected to an SBS2011 Standard domain. The only DNS server is the SBS2011 server. The same domains work fine on all client PCs I have tried, and the same ones do not work. Using nslookup, I get 'no such domain' errors for facebook.com, and the correct DNS entries for the ones that do work. When I add Google's Public DNS to my client PC as a backup (primary = local SBS server, secondary = 8.8.8.8), everything works fine for my client PC, but querying from the SBS server directly or from other client PCs are broken (so I don't believe it's a firewall issue). My main question is how can I see what servers the SBS2011 server queries if it doesn't know about a domain? There is nothing in our firewall logs that say it blocked any DNS-based packets, but I also wanted to query based on the IP/FQDN on the servers that the SBS server was likely to contact to find out about facebook.com for example. Update 23/05/2012: It appears DNS is working again this morning for the affected websites. Both the DC on its own and all client PCs can once again access the websites that were not loading last night, as well as the websites that were working. I haven't changed anything overnight, so it appears that there was some kind of temporary glitch, but I can't understand what would have caused it on the network.

    Read the article

  • Dell Vostro Desktop error.

    - by goldenmean
    Faced a strange situation at work today. We have people sitting at a table on opposite sides, with power cables underneath the table. This morning when the person sitting opposite to me banged his feet on ground, it disturbed the power cable to my PC and it turned-off. So when I turned it on, it says, "No boot device found" Press F1 to setup or F5 to perform test... There was no physical impact/crash/fall of the desktop cabinet, which could have crashed/damaged the hard disk physically. EDIT: The OS is Windows 7 So I tried to recognize it in the Bios setup, but even there it could not find the SATA disk that is connected to this machine. So then I opened the cabinet, removed the power supply and plugged it back again. Tried to reboot, same error, "Boot device not found" It is not recognizing the hard disk. Any ideas about what might be wrong? Hard-disk crash, OS Crash(But it doesn't even go to the point of loading the disk after the initial Bios execution, so doubt this...) Any pointers about how I should proceed to troubleshoot/solve this error are welcome.

    Read the article

  • Are these three brand new sticks of RAM really dead?

    - by David Brown
    I'm working on a Dell Dimension 4700 desktop for a friend. It came with 512MB of DDR2 RAM (two sticks of 256MB). One morning, it started blue screening on startup with no helpful error messages. It refused to boot into any form of Windows installation, including Safe Mode, original recovery disk, and my custom Windows PE disk. It did boot into the Ultimate Boot CD, so I ran memtest86, which reported errors everywhere. I removed one stick of RAM and the system booted up just fine. I moved the remaining stick into each slot and the system continued to operate normally, so I came to the conclusion that the stick that I removed was dead. I ordered an exact replacement, along with 2 more sticks of 256MB DDR2 (again, exactly the same as the original), bringing the total system memory to 1GB. Upon installing the three brand new sticks, the system blue screened again, this time stating that win32k.sys attempted to write to read-only memory. I inserted my custom Windows PE disk in order to get a better look at the memory dump with BlueScreenView, but it refused to boot and produced another blue screen, but without an error message. I removed each new stick one-by-one, restarting each time. It continued to blue screen until I was left with only the original stick. I then tried inserting the new sticks in various different orders, but this only produced more blue screens. I reinserted all three sticks (along with the original) and ran memtest86 again, which reported errors all over the place. So, now I'm right back where I started. I don't think it could be the slots themselves, because I can plug the original stick into any slot and it works just fine. System setup reports each stick correctly and shows the total as 1GB, however. It just seems strange to me that all three brand new sticks of RAM could be dead on arrival. Is there something I missed? Or should I just go ahead and RMA them?

    Read the article

  • Can't get php+sqlite working

    - by facha
    Hi, everyone I'm struggling all morning to make php work with an sqlite database. Here is a piece of php code that I try to execute: #less /var/www/html/test.php <?php $db=new PDO("sqlite:/var/www/test.sql"); $sql = "insert into test (login,pass) values ('login','pass');"; $db->exec($sql); ?> Here is how I've done tests: # sqlite3 /var/www/test.sql sqlite> create table test (login varchar,pass varchar); #chown apache:apache /var/www/test.sql #chmod 644 /var/www/test.sql Here is the stuff that drives me mad: When I execute from command line: #php test.php everything goes well. Sql is being executed and I can see a new row appear in the database. When I execute the same script from a browser - sql is not being executed. I don't get a new row in the database. There are no errors in the apache log file. Please, help

    Read the article

  • How to keep subtree removal (`rm -rf`) from starving other processes for Disk I/O?

    - by David Eyk
    We have a very large (multi-GB) Nginx cache directory for a busy site, which we occasionally need to clear all at once. I've solved this in the past by moving the cache folder to a new path, making a new cache folder at the old path, and then rm -rfing the old cache folder. Lately, however, when I need to clear the cache on a busy morning, the I/O from rm -rf is starving my server processes of disk access, as both Nginx and the server it fronts for are read-intensive. I can watch the load average climb while the CPUs sit idle and rm -rf takes 98-99% of Disk IO in iotop. I've tried ionice -c 3 when invoking rm, but it seems to have no appreciable effect on the observed behavior. Is there any way to tame rm -rf to share the disk more? Do I need to use a different technique that will take its cues from ionice? Update: The filesystem in question is an AWS EC2 instance store (the primary disk is EBS). The /etc/fstab entry looks like this: /dev/xvdb /mnt auto defaults,nobootwait,comment=cloudconfig 0 2

    Read the article

  • Inbox not updating in Exchange 2010, all users affected

    - by TuxMeister
    I'm battling against this darn issue this morning. We have the following setup: Big Hyper-V machine hosting the servers as VM's VM for CAS: WEB.XXX.local VM for Mailbox: EXC.XXX.local Servers are running Server 2008 R2 with Exchange 2010 SP1 Clients are all running Windows 7 Pro x64 with Outlook 2010 x64 The problem we're having is that nobody is able to see any emails received today (16th of October), but they are able to send externally. When I reply back to the email received externally, I don't get an NDR, yet the user cannot see my email. This is what I found and tried thus far: If we create a subfolder in Outlook 2010 and move any email from the inbox into that folder, changes will be immediately reflected in OWA We've been sending test emails to other users internaly and external email addresses and the sent items folder contains all those tests, synced properly to OWA as well Have tried crating a new profile, new emails are still missing Tried disabling Cache Mode, still no luck Also disabled "Download shared folders", still no luck Tried to setup a brand new Exchange mailbox and configured it on a VM that never had Outlook on it, still the same issue Tried restarting Exchange services on both CAS and Mailbox servers, no luck Tried rebooting both CAS and Mailbox servers, still no luck Performed a Mailbox Discovery on my admin account, emails from today are being found in the Discovery results, so the stuff is there, just not updating the user inboxes Any idea about what this hellish thing can be? I've done everything I can think of and also everything I could find out there. Let me know if you need any more details and thanks for reading this!

    Read the article

  • Ubuntu 10.10 forgets desktop theme.

    - by Marcelo Cantos
    I am running Ubuntu in VirtualBox (on a Windows 7 host). Several times now, the top-level menu bar, the task bar — and seemingly every system dialog — have forgotten the out-of-the-box "Ambiance" theme they conform to when I first installed the system. Window captions still preserve the theme, but pretty much nothing else does. I have searched high and low on Google for assistance with this problem. Everything I've found suggests either running some gconf reset or deleting .gconf* .gnome* and other similar directories. I have followed all this advice and nothing works. I still get a boring Windows-95-style gray 3D look and feel. On previous occasions, after much messing around I've given up and rebooted the VM instance, and been pleasantly suprised to see the original "Ambience" theme restored throughout the UI, but invariably it disappears again some time later, usually after a reboot, so I can never figure out what I did that broke it. Here's a sample from Ubuntu's site of what I want it to look like. And here's a screenshot of my system as it currently looks. Also note that my GNOME Terminals normally have a nice purple semi-translucent look, and as can be seen from the screenshot, they are now just a solid matt white. This last time (just this morning), trying numerous combinations all the usual tricks and rebooting several times hasn't fixed it, so here I am on SU wondering: How do I recover the out-of-the-box theme for my Gnome/Ubuntu desktop, noting that blowing away all config files — as suggested in many places online — fails to achieve this? EDIT: It might help to know that it seems to fail either after I resize the VM instance, forcing the Ubuntu desktop to resize itself, or after I play around with Compiz settings. I haven't been able to figure out which of these it is, and it could be neither. Given the amount of pain I have had to go through to get things back to normal (and given that I am at a loss as to how to do so), it has proven difficult to definitively isolate the cause.

    Read the article

  • Boot drive not found issue after cloning using Apricorn EZgig

    - by TomWilsonFL
    A couple days ago I cloned a drive for someone using the EZgig software. Usually this goes without a hitch, but this particular drive I was cloning is quite old. When I restarted with the new drive I received the typical bootable disk not found message, so I turned it off, messed with the BIOS, restarted and it came up fine. That night I was working remotely on the computer and had to restart it. It didn't come back up; not a good sign. When the user came to the computer in the morning it was giving the same message. I have found that to make the computer boot, all I have to do is go into the BIOS and "Load Defaults", then restart. It will boot and runs great. Any thoughts on what is causing this situation? Is it MBR corruption? Are some settings being saved in the CMOS? A couple points of mention: I have already attempted looking for a BIOS update for the computer, but the newest is already installed (from 2003). When the computer reboots it either shows "None" for Primary Master, or sometimes it will just not show anything. Thanks, Tom

    Read the article

  • Users getting 'flooded' with not read notifications (NRNs) for old emails and meeting requests

    - by Exile
    I'm being placed under quite a lot of pressure from senior management over a relatively trivial issue. Basically the vast majority of users are complaining that they receive not read notifications (NRNs) for old emails and meeting requests in large numbers multiple times a day. I know something strange is happening because some are delivered at silly times in the morning (i.e 3AM or 4AM). The problem I have is that these some of these NRNs are from meeting requests and messages that are 120 days old, so some users have deleted the original message so I don’t actually know if the NRN is from an email or meeting request. This is typical of what users receive as a NRN: From: Sender Sent: 23 March 2012 04:16 To: Recepient Subject: Not read: Accepted: Status update Your message To: Sender Subject: Accepted: Status update Sent: Wednesday, November 23, 2011 8:59:00 AM (UTC) Dublin, Edinburgh, Lisbon, London was deleted without being read on Friday, March 23, 2012 4:15:32 AM (UTC) Dublin, Edinburgh, Lisbon, London. ... From: Sender Sent: 18 March 2012 01:13 To: Recepient Subject: Not read: Gold delivery - Sourcing module Your message To: Sender Subject: Gold delivery - Sourcing module Sent: Friday, November 18, 2011 9:37:58 AM (UTC) Dublin, Edinburgh, Lisbon, London was deleted without being read on Sunday, March 18, 2012 1:12:37 AM (UTC) Dublin, Edinburgh, Lisbon, London. I have done a search and found the following: http://support.microsoft.com/kb/2544246 http://support.microsoft.com/kb/2471964 But we already installed 'Update Rollup 6 for Exchange Server 2010 Service Pack 1' back in December, so I am not sure what we can do to fix this?

    Read the article

  • Why does Windows/Microsoft Updates always take such a long time to detect available updates?

    - by RLH
    It's a common task for many of us who work in any form of IT position using Windows. Eventually you have to install/re-install a version of Windows and what follows is a very long OS updating process. For a long time I have accepted the fact that this is a slow process and that's all there is to it. There is a lot to download, and some updates require restarts followed by further updates... Ugh! This morning I had to go through the process of installing Windows XP with SP3. I'm installing the OS on a VM on an SSD and I've been working on this thing for over 6 hours. Although, think there are many ways to knit-pick this process for improvements, there is one step that is always particularly slow and I can not figure out a good reason why. That step is the detection step on a manual update. Specifically, when navigate to the Windows (or Microsoft) Updates page, and then click the 'Custom' button to detect your updates. It appears that your PC just sits there for a painful amount of time. Check your Task Manager and it looks like your PC is, in fact, locked because your CPU isn't cooking but that's certainly not the case. Somethings happening but I have no clue what's going on? What is the updating software doing? If the registry was being searched, shouldn't my CPU usage peak? Does anybody know what's happening? I can loosely justify why some of the steps in the update process take so long. However, this one doesn't seem to have any reasoning.

    Read the article

  • Firefox v15.0 about:newtab inaccessible via the back button

    - by Willem
    As of this morning I upgraded my Firefox to version 15.0. Or well, it did it for me. That's when my issue began. I've configured Firefox so that when I open up a new tab via Ctrl-T that it loads the about:newtab page which was released in version 14.x(?). I use this functionality extensively. I visit a page from the about:newtab page, read it, press the back button and pick another frequent website from the display I want to visit. However as of v15.0 the latter part is no longer functioning, after visiting a website from the about:newtab page the back button will not let me go back to the about:newtab page. Firefox acts as if that history entry was never there. I've tried searching the release notes to see if this change was intentional or a reported bug, but I have not found anything related so far. Is there anyway to (re)configure the new Firefox v15.0 to let me access the about:newtab page via a tab's history? EDIT: It appears that this only affects the initial 'visit' to the about:newtab page when opening a new tab, manually visiting about:newtab will register it as a history entry and allow it to be navigated to via the back and forward buttons. So I guess this changes my question to 'How can I make Firefox 15.0 treat the inital page from a newtab as a history entry'.

    Read the article

  • Windows 7 Update freezes - what to do?

    - by Tom Tom
    Hi, Yesterday I shutdown my notebook, and Windows 7 Ultimate started to install automatic updates. After one hour, I noticed that the update was still running. I thought OK, I shall go to sleep and let it run. In the morning it was still running. Thus, I thought it had crashed, forced a shutdown of the notebook and then restarted it. With the same effect that the notebook is "freezing" at "Install Update 1 of 5". It does not look like it has crashed. The progress wheel is still moving. But it does not make any progress... Would appreciate any help! Edit: OK, I was able to log-in into safe mode. This way I passed the install update screen. I do not want to generally disable updates, what can I do to not install the last update, which is creating troube. Or how can I find out whats the problem with the last update?

    Read the article

  • Ubuntu 8.04 wont reboot from script

    - by Littlejon
    I have a script that is run to backup a server via Rsync, after that script is run I want the server to reboot. My script is run as root from the Crontab at 3am in the morning. #!/bin/bash HOST="email" RSYNC_OPTS="-a -v -v --progress --stats --delete" RSYNC_DEST="10.0.0.10::$HOST" BACKUP_LIST="/etc /home /root" TIMESTAMP="/timestamp-bkup-start.chk" TIMESTAMP2="/timestamp-bkup-stop.chk" touch $TIMESTAMP rsync $RSYNC_OPTS $TIMESTAMP $RSYNC_DEST for BACKUP_ITEM in $BACKUP_LIST; do rsync $RSYNC_OPTS $BACKUP_ITEM $RSYNC_DEST done /etc/init.d/zimbra stop sleep 60s rsync $RSYNC_OPTS /opt $RSYNC_DEST touch $TIMESTAMP2 rsync $RSYNC_OPTS $TIMESTAMP2 $RSYNC_DEST echo `date +%Y%m%d%H%M` >> /var/log/reset reboot # $# shows number of args passed # $1 to access first variable #if [ $# -eq 1 ]; then # if [ $1 = "withreboot" ]; then # echo "rebooting..."; # echo `date +%Y%m%d%H%M` >> /var/log/reset # /sbin/reboot # fi #fi I have tried using init 6 rather then reboot. I have tried /sbin/reboot. I also have another basic script that just echos to the reset log and runs reboot without issue. It is just with the script above the server wont restart. If anyone has any theories that would be great as I have run out of idea. Thanks, Jon

    Read the article

< Previous Page | 82 83 84 85 86 87 88 89 90 91 92 93  | Next Page >