Search Results

Search found 33247 results on 1330 pages for 'anonymous access'.

Page 87/1330 | < Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >

• Cisco ASA - Enable communication between same security level

  - by Conor

  I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

  Read the article

• HTTP/1.1 503 Service Unavailable Exchange 2003 OWA

  - by toups

  Receiving HTTP/1.1 503 Service Unavailable when trying to access exchange web access. Server 2003 & Exchange 2003 Have tried: Deleting virtual directories and rebuilding them in IIS Restarting Dismounting & mounting the public folder store & mailbox store It's not AppPoolQueueLength Restarting all services (all proper ones are running) Making it use ssl or not (regular http) -- same thing for both Installing IIS & exchange 2003 on a new 2003 box as a new FE server, OWA on that gets same error. Not sure why it's getting a 503... was working without an issue and randomly is stuck at this no matter what; ll users can still successfully connect and use via outlook, only the web access is having issues. Any suggestions would be appreciated.

  Read the article

• Using pscp and getting permission denied

  - by Espen

  I'm using pscp to transfer files to a virtual ubuntu server using this command: pscp test.php user@server:/var/www/test.php and I get the error permission denied. If I try to transfer to the folder /home/user/ I have no problems. I guess this has to do with that the user I'm using doesn't have access to the folder /var/www/. When I use SSH I have to use sudo to get access to the /var/www/ path - and I do. Is it possible to specify that pscp should "sudo" transfers to the server so I can get access to the /var/www/ path and actually be able to transfer files to this folder?

  Read the article

• Windows user cannot connect via application, but can via Remote Desktop

  - by C. Ross

  I have an application (ASG-Zena) giving an 1385 error (Logon failure: the user has not been granted the requested logon type at this computer) when trying to run a batch job. I have checked on "Access this computer from the network" includes Everyone and Administrators and many others. "Deny access to this computer from the network" make sure that Guest is not listed there. If you still have problems, then maybe make sure that nothing is listed there. Administrative tools...local security policy..security options "Network access sharing and security model for local accounts" there are 2 options either classic or 'guest only'. Mine is set to classic. (These diagnostics come from this post) The account in question is added to the Administrator group on this computer. I know the login is valid because I regularly login to the server via remote Desktop. What other settings should I check?

  Read the article

• Protect apache pages by URL

  - by Thomas

  Is it possible to allow access to specific URLs only to certain networks? Basically, I would like to restrict access to the admin area only to the local network This area's pages are prefixed by /admin Essentially, I would like all /admin/* to be forbidden from public access. Can apache handle such a case? Thanks UPDATE Using your suggestions I came up to <LocationMatch admin> Order allow,deny deny from all Allow From 192.168.11.0/255.255.255.0 </LocationMatch> However, I get 403 even though I am on the network. Additionally, if I put apache behind haproxy, is this going to work? Because the traffic will be coming from 127.0.0.1 to apache

  Read the article

• IIS HTTP Error 403.1 - Forbidden: Execute access is denied

  - by coxymla

  I have a ASP.NET 1.1 application running on IIS 6 / Windows Server 2003. It's our application, but we're trying to specifically replicate a customer's installation so the app folder has been copied entirely from their production server onto our test machine, and then we've created the Virtual Directory and Web Application for IIS manually. The problem I have is that when we access the app, we get the standard IIS security error message: The page cannot be displayed You have attempted to execute a CGI, ISAPI, or other executable program from a directory that does not allow programs to be executed. -------------------------------------------------------------------------------- Please try the following: •Contact the Web site administrator if you believe this directory should allow execute access. HTTP Error 403.1 - Forbidden: Execute access is denied. Internet Information Services (IIS) Now this is pretty standard, except as far as I can see it's not anything so simple. I have checked: IIS user has read access to the directory IIS user and Network Service users have read/write access to the Temporary ASP.NET Files folder Virtual directory is set to the correct version of ASP.NET ASP.NET 1.1 Web Service Extension is allowed Virtual directory has the correct mappings of file extensions and all verbs to the aspnet 1.1 DLL Virtual directory properties allow Scripts and Executables to be run Anonymous access is turned on and the username and password is correct What am I missing?

  Read the article

• Access SSAS cube from across domains without direct database connection

  - by SuperKing

  Hello, I'm working with SQL Server Analysis Services for the first time and have the dilemma of working on a project in which users must be able to access SSAS Cubes (via a custom web dashboard) that live across different servers and domains, but without having access to the other server's SSAS database connection strings. So Organization A and Organization B will have their own cubes on their own servers, but Organization A users must be able to view Organization B's cubes, and Organization B users must be able to view Organization A's cubes, but neither organization should have access to the connection string. I've read about allowing HTTP access to the SSAS server and cube from the link below, but that requires setting up users for authentication or allowing anonymous access to one organization's server for users of another organization, and I'm not sure this would be acceptable for this situation, or if this is the preferred way to do this. Is performance acceptable here? http://technet.microsoft.com/en-us/library/cc917711.aspx I also wonder if perhaps it makes sense to run a nightly/weekly process that accesses the other organization's SSAS database via a web service or something, and pull that data into a database on the organization's server, and then rebuild the cube. Then that cube would be queried without having to go and connect to the other organization server when viewing the cube. Has anyone else attempted to accomplish something similar? Is HTTP access the standard way to go for this? Or any other possible options? Thanks, and please let me know if you need more info, still unclear on how some of this works.

  Read the article

• Registry access error when Migrating ASP.NET application to IIS7

  - by fande455

  I'm running windows 7 64-bit and iis7. I'm trying to setup a web application that was previously in iis6 on XP. It's giving me the error below. I've added the network service user to the Performance Monitor Users group to no avail. Access to the registry key 'Global' is denied. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.UnauthorizedAccessException: Access to the registry key 'Global' is denied. ASP.NET is not authorized to access the requested resource. Consider granting access rights to the resource to the ASP.NET request identity. ASP.NET has a base process identity (typically {MACHINE}\ASPNET on IIS 5 or Network Service on IIS 6) that is used if the application is not impersonating. If the application is impersonating via , the identity will be the anonymous user (typically IUSR_MACHINENAME) or the authenticated request user. To grant ASP.NET access to a file, right-click the file in Explorer, choose "Properties" and select the Security tab. Click "Add" to add the appropriate user or group. Highlight the ASP.NET account, and check the boxes for the desired access.

  Read the article

• "Decompile" Javascript function? *ADVANCED*

  - by caesar2k

  [1] Ok, I don't even know how to call this, to be honest. So let me get some semi-pseudo code, to show what I'm trying to do. I'm using jquery to get an already existing script declared inside the page, inside a createDocument() element, from an AJAX call. GM_xmlhttprequest({ ... load:function(r){ var doc = document_from_string(r.responseText); script_content = $('body script:regex(html, local_xw_sig)', doc).html(); var scriptEl = document.createElement('script'); scriptEl.type = 'text/javascript'; scriptEl.innerHTML = script_content; // good till here (function(sc){ eval(sc.innerHTML); // not exactly like this, but you get the idea, errors alert('wont get here ' + local_xw_sig); // local_xw_sig is a global "var" inside the source })(scriptEl); } }); so far so good, the script indeed contains the source from the entire script block. Now, inside this "script_content", there are auto executing functions, like $(document).ready(function(){...}) that, everything I "eval" the innerHTML, it executes this code, halting my encapsulated script. like variables that doesn't exist, etc removing certain parts of the script using regex isn't really an option... what I really wanted is to "walk" inside the function. like do a (completely fictional): script = eval("function(){" + script_content + "};"); alert(script['local_xw_sig']); // a03ucc34095cw3495 is there any way to 'disassemble' the function, and be able to reach the "var"s inside of it? like this function: function hello(){ var message = "hello"; } alert(hello.message); // message = var inside the function is it possible at all? or I will have to hack my way using regex? ;P [2] also, is there any way I can access javascript inside a document created with "createDocument"?

  Read the article

• Trouble with LINQ databind to GridView and RowDataBound

  - by Michael

  Greetings all, I am working on redesigning my personal Web site using VS 2008 and have chosen to use LINQ to create by data-access layer. Part of my site will be a little app to help manage my budget better. My first LINQ query does successfully execute and display in a GridView, but when I try to use a RowDataBound event to work with the results and refine them a bit, I get the error: The type or namespace name 'var' could not be found (are you missing a using directive or an assembly reference?) This interesting part is, if I just try to put in a var s = "s"; anywhere else in the same file, I get the same error too. If I go to other files in the web project, var s = "s"; compiles fine. Here is the LINQ Query call: public static IQueryable pubGetRecentTransactions(int param_accountid) { clsDataContext db; db = new clsDataContext(); var query = from d in db.tblMoneyTransactions join p in db.tblMoneyTransactions on d.iParentTransID equals p.iTransID into dp from p in dp.DefaultIfEmpty() where d.iAccountID == param_accountid orderby d.dtTransDate descending, d.iTransID ascending select new { d.iTransID, d.dtTransDate, sTransDesc = p != null ? p.sTransDesc : d.sTransDesc, d.sTransMemo, d.mTransAmt, d.iCheckNum, d.iParentTransID, d.iReconciled, d.bIsTransfer }; return query; } protected void Page_Load(object sender, EventArgs e) { if (!this.IsPostBack) { this.prvLoadData(); } } internal void prvLoadData() { prvCtlGridTransactions.DataSource = clsMoneyTransactions.pubGetRecentTransactions(2); prvCtlGridTransactions.DataBind(); } protected void prvCtlGridTransactions_RowDataBound(object sender, GridViewRowEventArgs e) { if (e.Row.RowType == DataControlRowType.DataRow) { var datarow = e.Row.DataItem; var s = "s"; e.Row.Cells[0].Text = datarow.dtTransDate.ToShortDateString(); e.Row.Cells[1].Text = datarow.sTransDesc; e.Row.Cells[2].Text = datarow.mTransAmt.ToString("c"); e.Row.Cells[3].Text = datarow.iReconciled.ToString(); }//end if }//end RowDataBound My googling to date hasn't found a good answer, so I turn it over to this trusted community. I appreciate your time in assisting me.

  Read the article

• Google Data Api returning an invalid access token

  - by kingdavies

  I'm trying to pull a list of contacts from a google account. But Google returns a 401. The url used for requesting an authorization code: String codeUrl = 'https://accounts.google.com/o/oauth2/auth' + '?' + 'client_id=' + EncodingUtil.urlEncode(CLIENT_ID, 'UTF-8') + '&redirect_uri=' + EncodingUtil.urlEncode(MY_URL, 'UTF-8') + '&scope=' + EncodingUtil.urlEncode('https://www.google.com/m8/feeds/', 'UTF-8') + '&access_type=' + 'offline' + '&response_type=' + EncodingUtil.urlEncode('code', 'UTF-8') + '&approval_prompt=' + EncodingUtil.urlEncode('force', 'UTF-8'); Exchanging the returned authorization code for an access token (and refresh token): String params = 'code=' + EncodingUtil.urlEncode(authCode, 'UTF-8') + '&client_id=' + EncodingUtil.urlEncode(CLIENT_ID, 'UTF-8') + '&client_secret=' + EncodingUtil.urlEncode(CLIENT_SECRET, 'UTF-8') + '&redirect_uri=' + EncodingUtil.urlEncode(MY_URL, 'UTF-8') + '&grant_type=' + EncodingUtil.urlEncode('authorization_code', 'UTF-8'); Http con = new Http(); Httprequest req = new Httprequest(); req.setEndpoint('https://accounts.google.com/o/oauth2/token'); req.setHeader('Content-Type', 'application/x-www-form-urlencoded'); req.setBody(params); req.setMethod('POST'); Httpresponse reply = con.send(req); Which returns a JSON array with what looks like a valid access token: { "access_token" : "{access_token}", "token_type" : "Bearer", "expires_in" : 3600, "refresh_token" : "{refresh_token}" } However when I try and use the access token (either in code or curl) Google returns a 401: curl -H "Authorization: Bearer {access_token}" https://www.google.com/m8/feeds/contacts/default/full/ Incidentally the same curl command but with an access token acquired via https://code.google.com/oauthplayground/ works. Which leads me to believe there is something wrong with the exchanging authorization code for access token request as the returned access token does not work. I should add this is all within the expires_in time frame so its not that the access_token has expired

  Read the article

• Handshake violation when trying to access one website

  - by Miguel

  I have a TZ 190 Wireless Enhanced with SonicOS Enhanced 4.2.1.0-20e. Yesterday, people could access without any problems a bank website wich uses HTTPS. Today, it is imposible to access only that website, every other ones works without problems. When checking the log message filtering to my IP only, this is what appears and I suspect is the cause of this problem, because all other websites are working: Priority: Notice Category: Network Access Message: TCP handshake violation detected; TCP connection dropped Source: X.Y.Z.3, 51997, LAN (admin) Destination: 200.14.232.18, 443, WAN Notes: Handshake Timeout Where X.Y.Z.3 is my local IP. I've tried to change TCP Settings under Firewall option, and activated this options with no success: Enforce strict TCP compliance with RFC 793 and RFC 1122 and Enable TCP checksum enforcement I've also tried to find the MTU and at first I got: Packet needs to be fragmented but DF set But when I lower the value of ping -f -l to 1468 I got: Request timeout. Also I deactivate CFS in lan and wan zones. Nothing works. Can you please help me? Any Ideas?

  Read the article

• Subversion Apache Ubuntu - Remote Access?

  - by Hollowsteps

  Okay, a couple days ago I built a bare bones kit into a machine. I've been running through tutorials to get it to work and right now I've gotten as far as making it available in my lan, hooray! However, I cannot access the repositories remotely. Any machine on the lan can easily access it through the hostname or, using 'outbound ip/hostname' or 'outbound ip/machine ip'. The machine can be pinged from a remote, non-lan machine and responds. I just can't get anyone into it outside of my lan. I've been trying to figure it out but I'm lost. I'm breaking a few rules and if any of these would be my problem, please indicate. I don't think I have a static IP (However I check my outbound IP whenever I do testing, is that not enough? It has stayed the same for 5+ days) I have not discussed this set-up with my service provider (Does Optimum Online block port 80? If so, can I just switch apache to listen on a different port?) I am in the DMZ of my router. This is what allowed it to be pinged remotely. For security reasons the machine that is in that zone is turned off most of the time until I can get it locked down. Any help would be appreciated, even if it's just a couple of words I could google to understand what I'm doing wrong. Tortoise SVN does not allow access remotely, but it does within the LAN as well.

  Read the article

• Excel cannot access the file with IIS7&Windows Serer 2008 R2(64bit)

  - by user838204

  I have a web project(.Net4) that needs to access Excel file, but it ends up with the following error message: Error occured during file generation.Microsoft Excel cannot access the file 'D:\xx\xx\abc.xls'. There are several possible reasons: • The file name or path does not exist. (Actually it's there) • The file is being used by another program.(It cant happen) • The workbook you are trying to save has the same name as a currently open workbook. In IIS7, I use DefaultAppPool with the Identity "myservice" who's under the Group of Administrators. In the Authentication Page of my website under IIS, Anonymous Authentication was enabled and set to "Application pool identity" and ASP.NET Impersonation was disabled. After searching the solution for hours, I found the following but NONE of them work Create folder in C:\Windows\SysWOW64\config\systemprofile\Desktop. Plz refer:this Grant rights of "myservice" in Component Services. Plz refer:this One thing strange, there is nothing in the Group of IIS_IUSRS. Is that normal? Cause I remember at least two users (DefaultAppPool & Classic .Net AppPool). Plz tell me how to fix the access problem. I assume that's permission problem of IIS but I cant solve it. Thank you.

  Read the article

• How to scope access to a service to set of users, using OpenLDAP, and only OUs

  - by JDS

  Okay, here goes. Solving this will solve several problems for me (as I can reapply this knowledge to several extant, similar problems), but luckily I have a very specific, concise problem to describe. Enough preamble. Our hosting partner is setting up VPN access for us and is connecting it to our LDAP server. They are using Cisco VPN, the docs on setting this up are here: http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00808c3c45.shtml#maintask1 Specifically, note the screenshot in (5), under "ASDM" Now, I do NOT want to provide access to all of our users. I only want to provide access to our IT group. But I do not see a configuration option for LDAP groups on that web reference for the Cisco VPN. We are using: OpenLDAP 2.4 Static groups (i.e. "Group has the following members...") Single user OU, "ou=users,dc=mycompany,dc=com" Is it possible to provide an alias of some kind in OpenLDAP that creates another OU, "itusers", say, and lets me alias the members of that OU somehow? Something like: "cn=Jeff Silverman,ou=itusers,dc=mycompany,dc=com" is an alias for "cn=Jeff Silverman,ou=users,dc=mycompany,dc=com" And is NOT a separate, unique user account. Alternatively, should I just create a separate OU and manage it separately? It is a pain, but only 12-15 users will have to be managed that way, with two separate user accounts. But I hate this option - messy, unmanageable, unscalable. You know what I mean. I am open to any options. I've searched and read all over but I can't quite find an directly analagous example. I can't possibly be the only one who's had this problem! Thanks!

  Read the article

• Apache2 Enabling Includes module causes svn access to quit working

  - by Matthew Talbert

  I have dav_svn installed to provide http access to my svn repos. The url is directly under root, eg mywebsite.com/svn/individual-repo. This setup has been working great for some time. Now, I need SSI (server-side includes) for a project, so I enabled this module with a2enmod include. Now, tortoisesvn can't access the repo; it always returns a 301 permanent redirect. Some playing with it reveals I can access it in a browser if I'm sure to include the trailing / but it still doesn't work in TortoiseSVN. I've looked at all of the faq's for this problem with TortoiseSVN and apache, and none of them seem to apply to my problem. Anyone have any insight into this problem? I'm running Ubuntu 9.10 with Apache 2.2.12. The only change I've made to my configuration is to enable the includes mod. Here's my dav_svn conf: <Location /svn> DAV svn SVNParentPath /home/matthew/svn AuthType Basic AuthName "Subversion repository" AuthUserFile /etc/subversion/passwd Require valid-user </Location> and here's the relevant part of my virtual host conf: <Location /svn> SetHandler None Order allow,deny Allow from all </Location> Edit: OK, I've discovered that the real conflict is between the include module and basic authentication. That is, if I disable the include module, browse to the subversion repo, enter my user/pass for the basic authentication, I can browse it just fine. It even continues to work after I re-enable the include module. However, if I browse with another browser where I'm not already authenticated, then it no longer works.

  Read the article

• Citrix Access Gateway with Citrix Receiver

  - by vm370

  I'm currently using a Citrix Access Gateway with firmware 5.0.4 to provide access over an SSL-VPN to an isolated environment, which is connected to over the Citrix Access Gateway Client, which is delivered by the device by default. However we encountered different problems, e.g. that it's somehow not possible to get it out of the autostart (not registered as a service or in the autostart?!) and it killed the Cisco VPN Client, which is used in the company and unfortunately cannot be replaced. The Cisco client can also just be used again after a procedure with cleaning the registry from all CAG Client remains, which requires a lot of effort. Because of that, I'd like to check if there is an alternative to this client, since is this is a real pain... Unfortunately I couldn't find a way to use the Receiver with the CAG yet, but if you have any resources on how to build this workaround, I'd be very happy. Thanks a lot in advance UPDATE: If there are other alternatives I'd be even more happy, since using the Receiver would also mean that there is an issue with the ICA-Client, which is also used in our environments. From my experience, the Receiver and the ICA-Client are also no good friends...

  Read the article

• from svn to git (+ LDAP + password-less updates + passworded access control)

  - by Jayen

  We have an SVN setup and there are some things we dislike about it and some things we like about it. We want to move to git, but we're not sure exactly what setup will work for us. We're currently using SVN (w/ Authz) + Apache (w/ WebDAV & LDAP). Hook to update the live site [like] Live site update requires no additional interaction [like] Live site update uses stored password [dislike] Commits require centralized-password authentication [like] Commit from live site changes stored credentials [dislike] Access control (per repository) for commits [like] Point 5 above is the one that keeps stuffing us up. Someone makes a commit from the live site and then the hook breaks. We're thinking to use gitosis/gitolite to get access control, but as they use ssh keys, we won't be requiring passwords. We're also thinking to use git-http-backend, and use Apache for authentication, but then do we lose access control? Can the live site be automatically updated from a hook if Apache requires authentication? Can we combine git-http-backend and gitosis/gitolite somehow? Can we store http credentials with git?

  Read the article

• After update, suddenly lost ability to access Windows Server 2008 R2 shares from Windows XP clients

  - by Knute Knudsen

  Today I lost the ability to see my Windows Server 2008 R2 shares from any of my 3 Windows XP machines in my small office. The 5 Win7 machines haven't been affected (they are still able to browse/access the 2008 server), but none of my WinXP machines can access the 2008R2 server anymore. Yesterday (and for the previous year) everything was working fine. I do not have a domain setup. I can still access Win7 shares from WinXP clients. Browsing the server logs, I see that the following update was installed last night: > Installation Ready: The following updates are downloaded and ready for > installation. This computer is currently scheduled to install these > updates on ?Thursday, ?November ?15, ?2012 at 3:00 AM: > - Security Update for Windows Server 2008 R2 x64 Edition (KB2761226) > - Security Update for Microsoft .NET Framework 3.5.1 on Windows 7 and Windows Server 2008 R2 SP1 for x64-based Systems (KB2729452) > - Windows Malicious Software Removal Tool x64 - November 2012 (KB890830) > - Cumulative Security Update for Internet Explorer 9 for Windows Server 2008 R2 x64 Edition (KB2761451) It seems likely that something was changed in last night's update, but so far I haven't seen anything on microsoft.com to prove it. I did hear that XP is reaching the end of the road soon. Any ideas?

  Read the article

• Cannot access certain URL on my wireless

  - by dehmann

  Problem: On my wireless network at home, there is one URL that I just cannot access with my browser: http://research.microsoft.com/ I have no problems with the Internet connection otherwise. But on that address I just get The connection was reset The connection to the server was reset while the page was loading. from Firefox. I am using a DSL modem (Westell) and Linksys wireless router (using DHCP). When I use my neighbor's wireless connection I can access the microsoft site without a problem. Additional technical details: But with my connection, here is what I get from nslookup. It is weird: It first cannot find the address, but after I look up another address it can find it: $ nslookup research.microsoft.com ;; connection timed out; no servers could be reached $ nslookup google.com Non-authoritative answer: Name: google.com Address: 72.14.204.104 Name: google.com Address: 72.14.204.147 Name: google.com Address: 72.14.204.99 Name: google.com Address: 72.14.204.103 $ nslookup research.microsoft.com Non-authoritative answer: Name: research.microsoft.com Address: 131.107.65.14 But even after nslookup finds it Firefox still cannot access it. Here is what traceroute says: $ traceroute http://research.microsoft.com/ traceroute: Warning: http://research.microsoft.com/ has multiple addresses; using 8.15.7.117 traceroute to http://research.microsoft.com/ (8.15.7.117), 64 hops max, 40 byte packets 1 dslrouter.westell.com (1XX.XXX.X.X) 4.515 ms 2.760 ms 3.072 ms 2 * * * Traceroute just to the IP: $ traceroute 131.107.65.14 traceroute to 131.107.65.14 (131.107.65.14), 64 hops max, 40 byte packets 1 dslrouter.westell.com (1XX.XXX.X.X) 11.912 ms 2.684 ms 2.808 ms 2 * * * Comparison: Traceroute to google.com IP: $ traceroute 72.14.204.99 traceroute to 72.14.204.99 (72.14.204.99), 64 hops max, 40 byte packets 1 dslrouter.westell.com (1XX.XXX.X.X) 6.428 ms 6.981 ms 117.099 ms 2 * * * Any comments / help?

  Read the article

• Active Directory LDAP and user issues (using apache2 for svn access)

  - by CaCl

  I currently have a setup where I work that lets users use their active directory domain logins and passwords to authenticate and authorize access to Subversion. Currently I need to allow application accounts the same access. So our IT group creates application accounts in the active directory for us to use. But they want to be "secure" so they set the "Workstations Allowed" to be only a limited number of workstations. So when an application account hits the apache2 server for authentication they can't login for some reason and I'm having a heck of a time trying to debug. The error logs only show me: [Tue Apr 06 11:24:25 2010] [warn] [client 24.24.24.24] [3469] auth_ldap authenticate: user appuser13 authentication failed; URI /svn [ldap_simple_bind_s() to check user credentials failed][Invalid credentials] [Tue Apr 06 11:24:25 2010] [error] [client 24.24.24.24] user appuser13: authentication failure for "/svn": Password Mismatch I've checked the password numerous times and it appears to be correct but I can't seem to get the user to authenticate properly. Below is a snippet of the apache configuration for ldap: # Auth providers # Active Directory <AuthnProviderAlias ldap ldap1> AuthBasicProvider ldap AuthLDAPURL "ldap://dmain.company.com:389/dc=dmain,dc=company,dc=com?sAMAccountName?sub?(objectClass=*)" AuthLDAPBindDN "CN=svnuser13,OU=Application Accounts,dc=dmain,dc=teradata,dc=com" AuthLDAPBindPassword secret3 </AuthnProviderAlias> # Another set of users from a different group <AuthnProviderAlias ldap ldap2> AuthBasicProvider ldap AuthLDAPURL ldap://diffldapserver:389/dc=specialusers,dc=com?uid </AuthnProviderAlias> # Another set of users from a different group <AuthnProviderAlias file file1> AuthUserFile /var/svn/auth/htpasswd </AuthnProviderAlias> <Location /svn> DAV svn SVNPath /var/svn Satisfy Any Require valid-user AuthType Basic AuthName "SVN Repository" AuthBasicProvider ldap1 file1 ldap2 AuthzSVNAccessFile /var/svn/auth/access AuthzLDAPAuthoritative on Require valid-user </Location> Any help, like tips for debugging is appreciated!

  Read the article

• Samba Share - MS Excel when saved (can't access the file, there are several possible reasons)

  - by brain90

  Dear Fellow ServerFaulter, I have a weird problem in my samba share. I have one share definition for 3 client (A,B,C) This share contain some excel file which having a lot of formula and linked each other. Client A access the file with libre office (ubuntu), client B access with WinXP & MS Office 2003, The write and read process working successfuly on Both of them. The problem occur when client C accessing the same file with MS Excel 2003 (windows xp). This messagebox appear when he saving the file : Microsoft office excel cannot access the \\192.168.1.23\myshare\ There are several possible reasons: - The File ort path does not exist The file is being used by another program. - The workbook you are trying to save has the same name as a - Currently open workbooks. I was trying http://support.microsoft.com/kb/291204 but it didnt work. Below is my share definition : [brainshare] comment = brainshare path = /opt/brainshare/ valid users = @brainshare force group = brainshare read only = No create mask = 0775 veto files = /*.scr/*.eml/thumbs.com/ Help me please... Thanks in advance ! Server: Ubuntu 10.10, Samba version 3.5.4

  Read the article

• VMware Virtual Infrastructure Web Access not starting on Fedora 14

  - by FusionHammer

  I am running a Fedora 14 server with VMware Server 2. When I initially installed VMware Server, everything was working fine. This included accessing Web Access on port 8333 (https) and 8222 (http). I had to perform a server restart and afterwards, the Web Access is not starting when I run: /etc/init.d/vmware-mgmt start The VMware Server Host Agent starts [OK], but the Web Access has no [OK] or [Failed] next to it. I also checked ports 8333 and 8222 by running a netstat, but neither are showing up. In addition, I checked the proxy.log and client.log files in the following directory: /usr/lib/vmware/webAccess/tomcat/apache-tomcat-6.0.16/logs/ The proxy.log doesn't have entries in it past 9-18-2012, which is the date the server restart occurred. The client.log is empty. I not sure what is causing this issue or what log files will be helpful in narrowing down the cause. I could re-install VMware Server, but I would like to narrow down the cause as it could occur again with the new re-installed environment.

  Read the article

• Can't access my accelerated hard disk from msdos after installing linux on ssd cache

  - by Chibueze Opata

  I mistakenly installed Linux Mint on my ssd (forgot my PC actually came with one), when it detected a ~31GiB disk that it wanted to install to, I was a bit confused since I had brought out 30Gb in my primary disk for it, but I clicked continue. After installation, I tried to boot back into my Windows and it brought out some Intel Raid Disk Utility stuff saying I should disable acceleration on a disk something couldn't be found, I canceled it but whatever I tried, recovery tools, setups etc, I couldn't just access the drive which was apparently using the SSD as cache. Since then I've been stuck. I tried setting the 'raid' flag to the disk from 'gParted', still I couldn't. I tried the diskraid utility from windows recover disk, it said it couldn't detect any raid, diskpart sees the partition but doesn't see the volume, when I remove the raid flag, it sees the volume as one of raw type, and I can't access anything. I can however mount the drive from terminal in Mint and access my files, but I don't have any backup media at the moment so I can do a factory re-install. Please how do I go about solving the issue, precisely I would like to know how to boot into the drive again. Thanks!

  Read the article

• Sync Two Exchange accounts or Ready Only access to subfolders

  - by cpgascho

  This is two questions kind of. The situation is as follows. I am running SBS 2008 with Exchange 2007. There is a shared account which has subfolders to keep track of the process of jobs that are coming into the company (ie: sales) I need to give other people in the company read access to this mailbox not full control. When I give ready only access to the root other users can only see the Inbox and not subfolders. Permissions have to be applied to each folder. One solution I have considered is creating a secondary mailbox that everyone could have full access too which would have a one way sync from the sales mailbox to the secondary mailbox. Then people could see what was happening without messing up the main mailbox by accident (at worst they would mess up the secondary mailbox) Ideally I could find a way to propgate the READ ONLY Permissiosn to all the subfolders. I have tried using PFDavAdmin to do this but have not been able to get it to connect successfully from Windows 7 To Exchange 2007 Any idea on how to 1. Propogate permissions (get PFDavAdmin to work??!) 2. Sync mailboxes 3. Other solution? Thanks Chris

  Read the article

< Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >