Search Results

Search found 2370 results on 95 pages for 'av cable'.

Page 87/95 | < Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >

  • Setting a subdomain to access home machine with windows remote desktop

    - by ianhales
    I'm trying to remotely connect to home machine through Windows Remote Desktop (amongst other things, but this is currently my primary focus). I can do this fine using my home WAN's static IP (thank god for cable!) with port-forwarding, but I would like to access it from a subdomain of my web-site (e.g. home.mydomain.co.uk). In the cPanel for my hosting account, I've gone into DNS zones and altered the A-record to point to my WAN's IP, which I thought should do the job, but I still cannot connect. When I ping the subdomain, I get my web-host's IP, which I guess is to be expected as I believe the DNS of the host domain is used first, then my server handles the redirection of traffic to the IP in the A-record. Is this the correct idea? Do A-record changes suffer from the same propagation delays as DNS record changes, as I suppose that could explain it? (by the way, this thread confirms my thoughts that setting the A-record should be enough: Hostmonster Subdomain redirected to home server IP: How to ssh into home server using subdomain)

    Read the article

  • Hard drive write speed - finding a lighter antivirus?

    - by Shingetsu
    I recently have been getting a lot of system lag here (for example, the mouse and the display in general take about 15 seconds to react in the worst cases). After a lot of monitoring the resources, I found that the problem mainly happens when too much Disk I/O is being done. Three culprits have been identified: My browser had the highest write I/O with 35,000,000 I/O Write Bytes. Steam had the highest read I/O (when IDLE!!!) with 106,000,000 I/O Read Bytes. My antivirus (in both cases I will soon mention) was the runner up in both cases with: 30,000,000ish write and 80,000,000ish read. The first AV I had was Avast! which I had liked on my previous system. After noticing it taking so much I/O I switched to Panda (supposing it wouldn't use TOO much during idle phase). However it only used a bit less I/O. Just a lot less memory and cpu and somewhat more network. My browser at the moment is Maxthon 3 (which I like a lot). Before this I was running chrome which had similar data and much higher cpu when running in the background was enabled. I'm not going to be running steam all the time and there aren't many alternatives to it. I like my browser very much, but I AM willing to switch if there's an obvious problem (I'm in programming, however I'm not a very good sysadmin, especially not when it comes to windows). Finally, my system almost stops lagging when I turn off the antivirus (and preferably steam) (some remains but once in every 5-6 hours for a few seconds so it isn't a big problem). My question (has a few parts): Is it possible to configure steam to lower it's I/O usage? (and maybe network while we're at it?) Which antivirus (very preferably free) uses lowest I/O while idle (I leave PC alone during active scans so that isn't a problem). Is there an obvious problem with my current browser and, if so, is there a way to fix it or should I switch and, if so, to what? (P.S. I've been on FFox for some time too). Info on system: Windows 7 (32 bit T_T, I am getting a new one in a few months but I want to keep using system during that time though). Hard Drive (main) is a Raid0. (Also have an external 1TB one which contains steam (and steam alone). As such it doesn't get used by much anything other than steam and isn't a very large problem. However steam still uses some I/O of registry) CPU: Intel(R) Core(TM)2 CPU [email protected] RAM: 6GB (3.25GB usable) (this and CPU have little effect as shown in next section) Additional info: Memory usage during problematic times: 44% CPU usage during problematic times: 35% Page File: main drive: system managed. 1TB drive: none. The current system I'm using is about 6 years old and is mainly a place holder while I await the new one in a few months. Final words: this is my 1st post on Super User (this question wouldn't feel right on Stack Overflow where I usually stay). If it doesn't have it's place here please tell me. If anything is wrong with it, same. Edit Technically I'm looking for a live thread detection program with minimal IO usage. I already have good active scan capability: Kaspersky (the free scanner uses the paid database) and MalwareBytes. Edit 2 Noticed another one, it seems that windows media player has been using stuff even when off! Turning it off and restarting now. If the problem is fixed I'll tell you guys. The reason I didn't notice it before was because I didn't have resource manager in front of me at the MOMENT of the problem. Now I did and it was at the very top of the list!

    Read the article

  • Windows 7 does not detect my new hard drive?

    - by jasondavis
    I just built a really nice new PC. Some specs... Intel i7-930 CPU ASRock Extreme X58 motherboard with sata 3 and USB 3.0 12gb of G-Skill DDR3 RAM 80gb Intel G2 Solid state drive for Windows 7 and other programs to run on Windows 7 Pro 64bit OS 2 1gb grapghic cards for 4 monitor support Thats the main components. Well today my new 1tb western digital hard drive came which I plan to use for data to preserve the life of my SSD (hopefully). I hooked up it's sata power input and then hooked up it's sata data cable to a sata 2 port on my motherboard, I boot windows 7 and go into my computer and the drive is not showing up with my other drives. I then re-boot again and check again, no luck. I then shut down the PC and open the case back up, I then check my connections and they all look good. I then boot up and I can see the new HD is on and spinning. I then go into my BIOS settings to see if it registers there and it DOES! It shows I have a WD 1tb hard drvie on sata 2 port 6. So I am at a loss of why it is not showing up as an option in windows? Windows acts as if the drive is not there. Please help

    Read the article

  • Graphics artifacts/distortion with Win7 and nVidia

    - by Gepard
    Problem I encounter is rather hard to describe, so I provide a screenshot: http://dl.dropbox.com/u/1732760/video-distortion.png As you can see there are some horizontal stripes in random colors. These stripes appear sometimes in all windowed apps, games and on the desktop too. They tend to stay in place until I refresh window (or force it to to redraw by for example minimizing and maximizing again). They also tend to appear in the same place and shape multiple times, even if they disappear, it's very likely they will be again in the same place after a while. These artifacts do not blink or change if computer is idling. If I don't touch anything, do not use mouse, they will stay in place forever (unless some app redraws its window on its own). I first encountered this problem some weeks ago. Back then I thought it might be cooling problem, so I took out the graphics card, removed dust from the radiator and fan and put it into PC back. I also ran some stress test using Furmark (peak tempearature was ~65C) to see if the problem becomes more intense if the card gets hotter, but suprisingly no artifacts whatsoever appear during the stress test. Graphic card is Galaxy GeForce 7300 GT with DDR3 memory, was never overclocked. Drivers are the latest, from Nvidia site. OS is Windows 7 64-bit, updated. AMD64 3000+, 2GB RAM. I'm running a dual monitor setup with 2 19'' Samsung LCDs and problem is on both, so I assume it's not a monitor or cable issue.

    Read the article

  • windows 7 clock jumps back about every hour + internet disconnects

    - by IlyaD
    I have the weirdest problem, for the last few days every hour or so (not exact) the clock jumps about back in jumps of 15 to 60 minutes and after some time the internet disconnects. i can reconnect the internet by unplugging and plugging back the network cable. This is the second time this problem happens to me, the first time was when I installed VirtualBox. whaen I removed it the problem was gone. This time I have no idea what triggered it, the only thing I installed about the time the problem started was iTunes update (10.5.1) I tried removing it but the problem remained. (also tried to remove other programs i installed day or 2 before and it also didn't help) also, this is not a VM and currently I don't have any VM software. any ideas..? UPDATE since the solution is in the comments i'll write it here - apparently the windows time service got broken, this is the fix: http://technet.microsoft.com/en-us/library/cc738995(WS.10).aspx (run "fix it" from IE browser only) UPDATE 2 The fix didn't work, about 2 hours passed and first the internet disconnected and then the clock jumped back... This probably means that the problem is not only in the clock

    Read the article

  • 2 routers at home- how to connect with VNC?

    - by Charles Leviton
    I have two routers at home. First router is upstairs and is connected to the cable modem. 2nd router is downstairs and acts as "signal booster" for the 1st router. Devices connected to the upstairs router have IP addresses of the form 192.168.1.n Devices connected to the upstairs router have IP addresses of the form 192.168.2.n. I blindly followed instructions from a website to do this set up, just glad it works! Upstairs I have a PC running Win 7 64 bit. Its assigned IP is 192.168.1.7. I have a VNC viewer running on this. Downstairs I have a 2nd PC running Vista 32 Home edition bit that is connected to the 2nd router and has IP Address 192.168.2.114. VNC server is running on this. It's listening on 5900. There is no firewall. When I try to connect to this downstairs PC from upstairs it fails with message "Failed to connect to server". I cannot ping to this either. If I try to connect to this downstairs PC using VNC Viewer from another computer that's connected to the same downstairs router then it works like a charm. So what's the work around if the viewer is on a different "network"? I don't have any problems doing remote desktop connection from the downstairs PC to the upstairs PC even if they are connected to different routers. Router information- Upstairs- ASUS RTN13U, downstairs- DD-WRT v24 RC-5 Thanks! P.S. I posted this on the Ultra VNC forum as well but that doesn't seem to have a lot of activity, so taking the liberty to multipost.

    Read the article

  • ASA 5505 VPN setup. VPN works but still unable to reach devices in the inside network.

    - by chickenloop
    I've setup a Remote Access VPN on my Cisco ASA 5505. I'm able to connect to my ASA via my phone or the Cisco client, but I'm unable to reach devices in my inside LAN when connected via VPN. The setup is the following: Inside Network : 10.0.0.0/24 VPN_POOL: 172.16.0.0/24 Outside Network: 192.168.1.0/24 ASA is not the perimeter router, there is another device on the 192.168.1.0/24 network which is connected to my cable provider. Obviously UDP port 500 and 4500 are forwarded to the ASA's outside interface. Everything works perfectly, besides the VPN stuff. Config: interface Vlan1 nameif inside security-level 100 ip address 10.0.0.254 255.255.255.0 interface Vlan2 description Outside Interface nameif outside security-level 0 address 192.168.1.254 255.255.255.0 object network VPNPOOL subnet 172.16.0.0 255.255.255.0 object network INSIDE_LAN subnet 10.0.0.0 255.255.255.0 Then the exempt NAT rule. nat (inside,outside) source static INSIDE_LAN INSIDE_LAN destination static VPNPOOL VPNPOOL I don't think that the problem is with the VPN config, as I can successfully establish the VPN connection, but just in case I post it here: group-policy ZSOCA_ASA internal group-policy ZSOCA_ASA attributes vpn-tunnel-protocol ikev1 split-tunnel-policy tunnelspecified split-tunnel-network-list value Split-Tunnel default-domain value default.domain.invalid tunnel-group ZSOCA_ASA type remote-access tunnel-group ZSOCA_ASA general-attributes address-pool VPNPOOL default-group-policy ZSOCA_ASA tunnel-group ZSOCA_ASA ipsec-attributes ikev1 pre-shared-key ***** Any ideas are welcome. Regards.

    Read the article

  • Windows 7 explorer crashing trying to read external hard disk

    - by Mario De Schaepmeester
    I have a 1TB Western Digital hard drive which is almost full and last time I tried to plug it into my laptop, I got a Windows dialog saying "this hard drive needs to be formatted". I did not panic because I have experienced things like this before and I know it's often solved by simply re-inserting the drive. Now however, whenever I plug it in and try to browse it in explorer by going to "computer", the explorer process crashes after a while. I simply close explorer since it takes ages trying to read the disk and nothing happens. After searching on the internet, the best thing to do would be a chkdsk. I tried it via properties in explorer (which also took a good 5 minutes to open up), locks up as well, after waiting a couple of minutes it says there's no access to the disk so a chkdsk is not possible... I want to make clear that I always use safe removal before pulling out the USB cable. Last time however, safe removal just would not work and when trying to shut down Windows, the logoff screen just would not disappear (I've waited at least 10 minutes or so) and I powered off the PC by force. This may be the cause of the problems but the disk was still recognised immediately after that. I really don't want to format this thing because it contains C: clones of 3 computers and a lot of other stuff that I don't want to re-copy. What would be the best course of action? Update I got chkdsk working via the command line. I used the /F and /R options. I already got a bunch of lines saying "file record segment X is unreadable" or whatever it is in English, my OS is Dutch. It looks bad... Will chdsk repair these errors?

    Read the article

  • Custom PCI bracket with support, for custom PCB?

    - by newbiez
    I am considering to put a custom PCB card that I made, into my computer. It won't go on any PCI connector, it plugs in on a USB connector on the motherboard, via a ribbon cable. I need thou to plug a device to it; which means that either I leave the PCB outside the case, hanging by the ribbon (bad idea), or I could put it in a PCI slot, using a bracket. The issue is that the brackets that I have, do not have tabs, so I have no way to screw the PCB on them. I was hoping to find something that would allow me to put the PCB on it, and then just fit it in the PCI bracket opening, like this: http://www.idotpc.com/TheStore/pc/viewPrd.asp?idproduct=1203&idcategory=0 This one won't fit the bill since the holes are too close apart, compared to the one that I have already on the PCB (and can't make more holes). Do you know if there is a place where they make universal PCI bracket mounting systems for custom PCB? I just need one, so can't even order a custom one (they ask me 120 dollars for one). Thanks in advance!

    Read the article

  • Input/output error reading USB backup drive on CentOS 6.4

    - by Kev
    I'm suddenly seeing some strange behaviour on our USB backup drive that doesn't make sense to me: (2013-10-21 14:58:23 [root@newdc /]$ cd /mnt/backup/ (2013-10-21 14:59:03 [root@newdc backup]$ ls -la ls: reading directory .: Input/output error total 0 (2013-10-21 14:59:05 [root@newdc backup]$ df -h /mnt/backup Filesystem Size Used Avail Use% Mounted on /dev/sda1 917G 843G 28G 97% /mnt/backup How is it possible for the OS to know how much is in use, but I can't ls any of it as root? Or more to the point, what problem does this indicate? /var/log/messages said this: Oct 21 14:57:54 g5 kernel: EXT4-fs error (device sda1): ext4_journal_start_sb: Detected aborted journal Oct 21 14:57:54 g5 kernel: EXT4-fs (sda1): Remounting filesystem read-only But...read-only is something different than 'throw an io error'... After unmounting to try fsck on it, I had someone on-site look at it, and the drive was not spun up, and had a slow-flashing light, which I believe means it was in a power-suspend mode. So I had them unplug and replug the USB cable, and now (before remounting) it says: fsck from util-linux-ng 2.17.2 e2fsck 1.41.12 (17-May-2010) /dev/sda1: clean, 2805106/61046784 files, 181934167/244182016 blocks I then mount it and now ls works and df reports: Filesystem Size Used Avail Use% Mounted on /dev/sda1 917G 680G 191G 79% /mnt/backup What would cause it to go into such a state without being asked to? Why all the weird behaviour, and now it appears to not be corrupt?

    Read the article

  • My scanner isn't responding. It is connected to a SCSI interface using Windows XP

    - by Bob
    I have a Microtek ScanMaker 9600XL scanner. The best part about it is that it is 12x17 inches. Wowza! The worst part about it is that I've had it working at one point, with the same cable, same card, same computer, but have since re-installed Windows XP on it. Currently it will turn on, and blink the Power and Ready lights. They should be solid. I've done my best to find documentation for this, but all I've really gotten is the content on the Microtek site. I've tried turning the scanner on, then the PC. Turning the PC on, then the scanner. When I try launching the software it pops up a dialog saying "ScanWizard Pro can't find any scanners! Use SCSI Check to find a scanner." I know the scanner has a pair of little buttons on the back. These cycle up/down a counter. I think it goes 0-7. Any thoughts on what that does, or how to proceed troubleshooting? I think my next step is to try each of those numbers, and do both pc booted first, and scanner booted first for each of those numbers...

    Read the article

  • GA-P55A-UD4 SYSFAN 2 problem....

    - by Vit
    Hi, I have some strange problems with the mobo in title. I have two fans connected to SYSFAN 1 and 2. Both are the same temp regulated Arctic Cooling F12. They are regulated thru temp sensor which is in different cable from fan. It connects to the 3 pin. So, I connected them to SYSFAN 1 and 2 MB ports. The problem is, when PC starts, the fan connected to SYSFAN 1 spins nice and is reporting speed to BIOS. But second fan connected to SYSFAN 2 starts to spin, than stops. I tried to warm the sensor with no help. Also, in BIOS I found no feature about SYSFAN 2 mode or something. I tried the fan itself by connecting it to PWR fan connector and it works fine. But obviously I want it to operate in SYSFAN 2. Please if you have any advice, help. Thanks.

    Read the article

  • Router as primary DNS server, Server as alternate? (or vice versa)

    - by Jakobud
    We have a very small business network, with a typical cable modem hooked into a DD-WRT router. We also run a basic CentOS server that does a variety of things, including acting as the primary DNS server for the office. The reason we need an internal DNS server is because we do a lot of internal web development and use the DNS server to add/remove various local network URLs for internal website testing (like www.testsite.com.local). It's very important for us to be able to add/remove URL aliases easily to the DNS. The problem with this setup is that if we ever need to restart the CentOS server or take it offline for upgrades or whatever, then internet access for all computers on the network is lost. That's because each computer relies on that DNS server to access the Internet I guess? The router is online all the time and very very rarely has to be restarted. It would be nice if we could setup my router to be the primary DNS server but still be running DNS on my server. So we could still add my local testing website URLs to the DNS server in CentOS, but be able to also take down the CentOS server without loosing Internet access on the network. How would this be setup? Would I simply need to add both router + server IP addresses to each computer's IP settings? Is the router primary DNS and server secondary DNS server? Or vice versa? Or can one of the two serve as a fallback for the other? What (if anything) needs to be configured on both the router and server in order for them to recognize that the other DNS server exists on the network? Does anyone have any newb-friendly resources for setting up something like this?

    Read the article

  • Run 3 monitors on two different video cards?

    - by hullot
    Can I run 3 monitors on two different video cards? I have an ATI and Nvidia brand card. The ATI has 2 HDMI connections. They both work. Both cards are also picked up in Windows, one being the ATI and the other one as the Nvidia, but it says VGA Controller, although the card only takes 2 DVi. So, one DVI cable goes into that Nvidia card. 3 Monitors, but only 2 the HDMI ones from the ATI pick up, not the third one which is connected to the Nvidia via DVI. How can I run three monitors then? I suppose I can't install both drivers, so I'm unsure what to do. Is this possible? I just want the Nvidia card to power the third screen, no gaming on it, nothing. Also the ATI is picked up as primary card as well, so no hurdle there. EDIT: Hm, just installed the Nvidia drivers and it picked up the third screen no problem. Hope there aren't any major conflicts. Will post this as an answer as correct when I'm able. Can't as a new user.

    Read the article

  • Best way to patch (8) RJ45 ports from one room to another.

    - by zimmer62
    I have a 48 port patch panel in my basement, which I've wired almost all of them to various rooms around the house. Many are not actually being used at the moment, but pretty much all of them are wired to somewhere. As of recent, I've put in an HTPC in my media closet (different room), and I'm finding I need a lot more RJ45 plugs to this area. I have 4 drops here, and adding a switch will not solve my problems. I'm using the cabling for other things such as IR and Serial devices, not just Ethernet. What I'm hoping to do is add an 8 port panel in that media closet, and tie those into an 8 port panel on my rack next to the 48 port... What I don't want to do is pull 8 separate cables one by one from one area to the other unless someone has a technique that will allow me to do that quickly, and painlessly. Do they make cables with more conductors specifically for this purpose? Or patch panels that are designed for a special cable essentially just extending ports from one room to another?

    Read the article

  • How do I get to the bottom of network latency and bandwidth issues

    - by three_cups_of_java
    I recently moved two blocks south. That move moved me from Comcast to Broadstripe (high-speed internet cable providers). Comcast was pretty good. Broadstripe sucks. I called them on the phone, and they basically brushed me off (politely). I want to come to them with some numbers, so I can say more than just "it's really slow". I still have access to my old Comcast service, so I can run the tests using both providers. Here's what I'm seeing with my new Broadstripe service: 1) When I browse to most sites, there is a long delay (5-10 seconds) before the page starts loading in my browser 2) The speed test tell me I have 12 megs down (bullshit) 3) I have a server at my office. I just downloaded some files (using scp on the command line). It said I'm getting 3.5 KB/s I'm an experienced programmer and spend most of my days on the command line and in vim. Networking, however is not a strong point. I've played around with traceroute, but I'm not sure if that's the right tool to use. I have access to servers all over the country (I would just use Amazon EC2 to set up a test server), and I prefer to use Ubuntu for my testing. How can I come up with some hard numbers to show Broadstripe how crappy their service is?

    Read the article

  • Two cisco gigabit switches refuse to link to each other. Any idea why?

    - by Prody
    I have 3 Linksys SR2024 switches which are basically non-managed 24 port Gbit + 2 miniGBIC. I now had to add another switch to the network, and my provider didn't have the SR2024 switch anymore, so I got the Cisco SLM2024 which was a bit more expensive. It's pretty much the same thing but with management (that I don't need). So I've connected the SLM2024 to a SR2024 via Cat6 cable, and for some strange reason, I get no link. If I connect any machine with a Gbit NIC to both switches, it links with 1Gbit autonegotiated. If I connect the SLM2024 to a non-Gbit switch (I have a cheap 4port ASUS switch), it will link just fine on 100Mbit full duplex. Since the SLM2024 has management, I've tried to see if something is misconfigured on it's side, but it's not, it advertises 1Gbit and lower. (hence the machines connecting succesfully at 1Gbit). Since the SR2024 that I'm trying to connect it to also connects successfully with another SR2024 and other Gbit machines, it means that it advertises Gbit too. But for some reason when I link the SR2024 to the SLM2024 I get no link. Please note that I've properly tested the wire. Does anyone have any idea what's wrong?

    Read the article

  • Which Cardbus/PCMCIA -> USB card works with external hard drive?

    - by Carl
    I have an HT-Link Cardbus/PCMCIA USB 2.0 2-port card (NEC / 32-bit). My external hard drive w/USB adapter won't work with it, and it will work plugged directly into a USB port on a different laptop. (My USB ports got fried.) I got the card off E-Bay. My MP3 player works plugged into that card. The drivers for the card say "Known limitations: High Speed Isochronus, USB Composite Devices." (No other details provided.) I don't know if the hard drive adapter is "isochronous" or "composite." I've read there are problems with too little power being supplied to the drive. The cable to the drive has two USB plugs on one end, and it doesn't make any difference if I plug both of them into the Cardbus card. What card should I get? I see many different brands on E-Bay. I need one that supplies sufficient power for an external hard drive, and doesn't have any "known limitations" in the way.

    Read the article

  • How to fix missing RAID1 drive

    - by Sodved
    I had to do some fiddling about with my cables inside thebox and now I am getting a "Critical Error" about the RAID disks during startup. I have a gigabyte GA-MA770T-UD3 motherboard. Aparently the RAID controller is an AMD SB710 chip. I'm pretty sure I know what happenned. The first time I rebooted I had forgotten the power cable on one of the disks in the RAID1 (mirror) and let it boot up. So I shut down and put the power back in. So now when it boots up I go into the RAID admin interface (between the BIOS screen and the OS loading): it shows the RAID1 as in error the logical device has one disk and says the other is disconnected or missing the other physical disk shows up as a single disk If I boot to the OS (Windows 7 32 bit) the data all seems to be there. If I go into computer management it says my partition is on a disk and working OK. But the other disk is offline because: "The disk is offline because it has a signature collision with another disk that is online" So I am guessing because I STUPIDLY booted up with only one of the disks powered on, the other disk fell out of synch with the mirror and so now cannot rejoin the mirror. How do I fix this? I want to get the RAID1 mirror working again. There does not appear to be any "Repair" option in the basic RAID admin tool which I get into during startup before the OS boots. I have not made any explicit changes to the online one (but I guess the OS has probably written some admin data).

    Read the article

  • how to build network across buildings ?

    - by Omie
    Hi ! I need some help in building a network between hundreds of computers spread across multiple buildings of my college. Yes, I'll be doing this as a part of my college project. Please see this image, it will give you enough idea of what I'm trying to achieve. http://i.imgur.com/rOohx.png All the computers in all buildings should be able to connect server. Once network is up, there will be a set of services over intranet and network use will be moderate. well, say there will be an email server and a http server. My point is, I cannot afford much of performance loss. It feels easy to connect computers inside 1 building to each other, however, I'm clueless as to how to connect all of them to server. I mean, just 1 cable won't be enough to connect 1 building to server, right ? How should I go with it ? I am not expecting detailed configuration. Just heads up will do :) Thanks

    Read the article

  • Hard Drive problem: is it the SATA controller or the HDD itself?

    - by Drooling_Sheep
    I have a Samsung 1.5TB hard drive hooked up to an ECS H55H-I mini-ITX motherboard. I have XBMC 10 (modified Ubuntu 10.04) installed for use as an HTPC. The hard drive encounters occasional errors during normal use which cause it to be remounted read-only. I have updated the BIOS on the motherboard, changed the SATA cable and moved it to different ports on the motherboard, installed and re-installed the OS (including different versions of XBMC and generic ubuntu), all to no avail. I recently ran tests both with badblocks -sv and smartctl -t long. Both reported no errors. This makes me think the motherboard or SATA controller is probably the issue. Does anyone know of any further tests I can do to help narrow this down? The processor is a Core i3. I forget the model number but it's one of the 32nm ones with on-package graphics. There's no discrete video card or optical drive. The power supply is a 150W Rosewill (pretty sure) that came with the case.

    Read the article

  • Need recommendation: which USB card (PCMCIA) works with external hard drive?

    - by Carl
    I have an HT-Link Cardbus/PCMCIA USB 2.0 2-port card (NEC / 32-bit). My external hard drive w/USB adapter won't work with it, and it will work plugged directly into a USB port on a different laptop. (My USB ports got fried.) I got the card off E-Bay. My MP3 player works plugged into that card. The drivers for the card say "Known limitations: High Speed Isochronus, USB Composite Devices." (No other details provided.) I don't know if the hard drive adapter is "isochronous" or "composite." I've read there are problems with too little power being supplied to the drive. The cable to the drive has two USB plugs on one end, and it doesn't make any difference if I plug both of them into the Cardbus card. What card should I get? I see many different brands on E-Bay. I need one that supplies sufficient power for an external hard drive, and doesn't have any "known limitations" in the way.

    Read the article

  • Cannot access Domain Controller through VPN

    - by Markus
    In our small network there is a Windows 2008 R2 Domain Controller that also serves as Remote Access Server. For years, we could access this server and the resources in the network over a VPN connection without any problem. Since some time however, I am able to connect to the VPN, but my Windows 8 client (and another one I used for testing purposes) is not able to connect the domain controller afterwards. I can access any other server in the network, but there seems to be a problem regarding the trust between the client(s) and the server. If I connect the client to the network directly over a LAN cable, everything works as expected. Also I can connect to another server over VPN and open a RDP prompt to the DC without a problem. On the client, whenever I try to access the DC, I get an access denied message. I've tried to update the group policies both over VPN and LAN. Also, I've removed the client from the domain and re-added it. The client shows a message that Windows requires valid login information when connected to the VPN - but my credentials are valid. They work when I logon to the client when not connected to the VPN and also when connected to the LAN. Turning off the firewall on the client and the server did not change anything. DNS resolution works both on the server and the client. What else can I do to diagnose and solve the problem?

    Read the article

  • Linux can dual display but windows can't?

    - by Mr_CryptoPrime
    I have two monitors, one that is hdmi-to-dvi and the other vga-to-dvi. I have an AMD HD Radeon 6900 series graphics card installed. I got Ubuntu to display dual monitors, but then I restarted for an update and then Ubuntu wouldn't even boot in recovery mode, it just kept cycling forever...displaying something about "timeout: killing [filepath] [hexadecimal]. So I tried booting into windows (7-professional) and it crashed and displayed this after rebooting: IRQL_NOT_LESS_OR_EQUAL, PAGE_FAULT-IN-NONPAGED-AREA. I went into Bios and reverted to the system defaults and ran system restore and it booted ok, but the dvi-to-dvi monitor would not display. I made sure my drivers were updated and catalyst was updated. Also through research discovered only one is for vga and the other is digital only, so I put the vga-to-dvi in the vga slot and so on. Neither windows or catalyst will detect the dvi-to-dvi montior. Any suggestions? Thanks. EDIT: Found out that booting into Ubuntu with only one monitor (using either monitor with either cable) worked perfectly fine. I could then add another monitor and it displays ok. However, it will, out of the blue, suddenly distort the display. At first I thought the computer crashed, but it is something with the video output from the GPU to the monitor because I pushed the power button and it would refresh every 5secs or so and I could see the "Ubuntu will power down in X seconds", even though it was horribly distorted. Any ideas what's causing this?

    Read the article

  • Windows 7, network transmit (send) not working

    - by user326287
    My Win 7 works 2 years without problem. But now, I can't transmit (send) big data on LAN/Internet. I can: - Ping anything - Browse Internet, download files at full speed - Send e-mails with very small attachments. - Testing download speed on Speedtest.net, measure stable full speed. I can't: - Testing upload speed on Speedtest.net. Upload stuck.. - Save/send email messages with big (128k) attachment, independent from e-mail provider or e-mail box. THIS IS NOT A HARDWARE/CABLE/CARD OR OTHER NETWORK DEVICES PROBLEM! When I boot from a Linux Live CD, without ANY hardware change, all data sending, testing works correctly, at full speed. I have tried already in Win 7: - Disable Windows/3rd party Firewall completely - Reset IP stack parameters (netsh int ip reset c:\resetlog.txt) - Computer restore - Reinstall LAN driver When I inspect the packets in Wireshark in Windows, I see lot's of (maybe 60% of sent packets) "TCP Retransmission". Sometimes receive "TCP Dup Ack" or "TCP Out-of-Order". Linux don't do this. Thank you for the help.

    Read the article

< Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >