Search Results

Search found 3276 results on 132 pages for 'luck'.

Page 87/132 | < Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >

• "cannot receive new filesystem stream: invalid backup stream" error when unpacking flash archive on solaris 10

  - by Bovril

  I've searched around but i'm having no luck with some peculiar behavior with a flash archive. I'm using HP Server Automation 9.14 to deploy the OS. I'm creating a Solaris 10 flash archive to create a snapshot default build in our environment. I create the flash archive with # flar create -c -S -n g8-solaris10-u10 g8-solaris10-u10.flar It seems to create the file without any problems (exit status 0). When deploying to a new system (same hardware), it extracts to a point and then bails. The last error in the log I can see is Extracted 2047.00 MB ( 82% of 2488.98 MB archive) ERROR: Could not read file (172.27.118.100:/media/opsware/sunos/flar/g8-solaris10-u10.flar ERROR: Errors occurred during the extraction of flash archive. The file /tmp/flash_errors contains the list of errors encountered ERROR: Could not extract Flash archive ERROR: Flash installation failed The error log contained the following message cannot receive new filesystem stream: invalid backup stream A previous version of this flash archive (1.8gb) worked ok, so I suspect size may be a factor. The source system (the one the flash archive is an image of) is an HP BL460C GEN8 some more info below. OS version Info # uname -a SunOS testhostname 5.10 Generic_147441-01 i86pc i386 i86pc # who -r . run-level 3 Oct 15 08:15 3 0 S disks # echo | format Searching for disks...done AVAILABLE DISK SELECTIONS: 0. c0t0d0 <DEFAULT cyl 17841 alt 2 hd 255 sec 63> /pci@0,0/pci8086,3c06@2,2/pci103c,3355@0/sd@0,0 Specify disk (enter its number): Specify disk (enter its number): zpools # zpool list NAME SIZE ALLOC FREE CAP HEALTH ALTROOT rpool 136G 24.6G 111G 18% ONLINE - Zones # zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / native shared The file size of 2047 seems suspiciously close to 2048, which is concerning. Any help would be greatly appreciated. Thanks

  Read the article

• connect server to server on secondary NIC

  - by microchasm

  Hi, I have a CentOS box with multiple NIC's running Apache. I also have another box running RHEL that will be the MySQL server. I'm trying to use the secondary NIC on the Apache box to connect directly to the MySQL server, but so far no luck. I want to isolate the MySQL box as much as possible which is why I'm going for a direct connection as opposed to running through a switch. I have a crossover cable running between them. IP configs: Apache box eth0 [to lan] ip addr: 192.168.200.100 netmask: 255.255.0.0 gateway: 192.168.111.1 eth1 [to mysql] ip addr: 192.168.200.101 netmask: 255.255.0.0 gateway: [blank] MySQL box eth0 [to apache] ip addr: 192.168.200.203 netmask: 255.255.0.0 gateway: 192.168.200.201 The rest of our network is on 192.168.111.0/24 subnet. Ping only returns Destination Host Unreachable. I've tried various variations of this setup (including straight through cable), and I can't seem to get them to talk to each other. Any help appreciated.

  Read the article

• Fix: Connections to SQL Server 2005 on Windows Vista suddenly stop working

  - by NTulip

  On my Vista machine at work, applications and the SQL Server Management Console work fine connecting to SQL Server 2005. Sometimes they are ok for weeks at a time, sometime for hours and then they stop connecting. I've tried everything to get it to work including the installation of SPII and running the user provisioning tool without any luck. The only way to fix it was to restart. The Error: Connections are refused with the standard error message: Cannot connect to SERVER_NAME\INSTANCE_NAME ------------------------------ ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=-1&LinkId=20476 The Fix: Stop and restart the Sql Server Browser, Sql Server integration, SQL Server Active Directory Helper services. Works like a charm.

  Read the article

• SQL Server Analysis Services, DNS, AD, Kerberos, Connection Issues

  - by ScaleOvenStove

  Running into a very weird issue. Converting servers to Windows 2008/SQL 2008. Have a server, SERVER_A, brand new, setup with Win2k8,Sql2k8 - works. Have a Server SERVER_B, running Windows2003/SQL2005. I want to migrate from SERVER_B to SERVER_A. I have all db's, cubes, etc setup on SERVER_A and it is mimicking functionality. Since users are using Excel to connect to SSAS, they connection string has SERVER_B in it. What I want to do, is, change DNS on the network to point SERVER_B (by name) at the ip of SERVER_A. I have successfully done this with another server, SERVER_C, but I need to do it with SERVER_B. What I have found is that with SERVER_C, after changing DNS, had to remove SERVER_C from AD and then it worked. I could connect to SERVER_C (DB), SERVER_C (SSAS Default Instance) and SERVER_C (SSAS Named instance) and it all was actually connecting to SERVER_A I tried to do the same with with SERVER_B, and no luck. Changed DNS, removed from AD, and it wouldn't connect. Found out that there were some SPN's in AD set up, so removed those and tried again. I then could connect to SERVER_B (DB), SERVER_B (SSAS Named Instance), but not SERVER_B (SSAS Default Instance). I could connect to SERVER_B (SSAS Default Intance WITH the Port #), but I need to be able to connect without the port number. I am at a loss to as why I can't connect to the default instance without a port #. Not sure if it is SPN's in AD, or another AD issue, or something else. Pretty sure it isnt something on the server (because SERVER_C works!) Any insight or suggestions would be greatly helpful!!

  Read the article

• Getting Grub2 to recognize a Raid 10 boot/root

  - by xenoterracide

  I've been trying to get my raid to boot from grub2 for about 2 days now and I don't seem to be getting closer. The problem appears to be that it doesn't recognize my raid at all. It doesn't see (md0) etc. I'm not sure Why or how to change this. I'm using mdadm, 2 device (essentially a raid1) raid10,f2, which is currently degraded. I have tried adding the raid and mdraid modules with grub install along with others. I've tried several variation on grub-install such as grub-install --debug --no-floppy --modules="biosdisk part_msdos chain raid mdraid ext2 linux search ata normal" /dev/md0 I've been searching the net for an answer to what I haven't done but no luck. On my other drive which I plan on removing the raid is initialized and mounted fine on boot, but it's not the boot/root for that setup. My grub.cfg isn't recognized by grub since it can't read the raid partition so I'm not posting that. md0 is not listed in my /boot/grub/device.map.

  Read the article

• "Unable to initialize module" fileinfo php-pecl-Fileinfo.x86_64

  - by Myers Network

  I have a brand new server server that I am trying to get setup up. This is a 64 bit machine that I can not install "fileinfo" or "memcache". I have uninstalled these and reinstalled them using yum and pecl with no luck. Yum install fine "no error" but then get error when running php. pecl from what I can tell is only installing 32bit. Does not put anything in the lib64 directory. Here is my output from php -v: PHP Warning: PHP Startup: fileinfo: Unable to initialize module Module compiled with module API=20050922, debug=0, thread-safety=0 PHP compiled with module API=20060613, debug=0, thread-safety=0 These options need to match in Unknown on line 0 PHP Warning: PHP Startup: memcache: Unable to initialize module Module compiled with module API=20050922, debug=0, thread-safety=0 PHP compiled with module API=20060613, debug=0, thread-safety=0 These options need to match in Unknown on line 0 PHP 5.2.14 (cli) (built: Aug 12 2010 16:03:48) Copyright (c) 1997-2010 The PHP Group Zend Engine v2.2.0, Copyright (c) 1998-2010 Zend Technologies Here is some other system info incase you need it uname: Linux server.actham.us 2.6.18-194.26.1.el5 #1 SMP Tue Nov 9 12:54:20 EST 2010 x86_64 x86_64 x86_64 GNU/Linux php -m: PHP Warning: PHP Startup: fileinfo: Unable to initialize module Module compiled with module API=20050922, debug=0, thread-safety=0 PHP compiled with module API=20060613, debug=0, thread-safety=0 These options need to match in Unknown on line 0 PHP Warning: PHP Startup: memcache: Unable to initialize module Module compiled with module API=20050922, debug=0, thread-safety=0 PHP compiled with module API=20060613, debug=0, thread-safety=0 These options need to match in Unknown on line 0 [PHP Modules] bz2 calendar ctype curl date dbase dom exif filter ftp gd gettext gmp hash iconv imap json ldap libxml mbstring mcrypt mysql mysqli openssl pcntl pcre PDO pdo_mysql pdo_sqlite readline Reflection session shmop SimpleXML sockets SPL standard tokenizer wddx xml xmlreader xmlrpc xmlwriter xsl zip zlib [Zend Modules] Any help would be greatly appreciated, thanks....

  Read the article

• Apache, suexec, PHP, suPHP

  - by Chris_K

  While I'm quite comfortable as a Linux user, my Linux Admin-fu is a bit weak. Thus, I'm here looking for guidance with a CentOS server I'm about to build. I need to setup an Apache2 web server for a few of our clients. I want each client's web content to be under their home directory (USERDIR in apache.conf, right?) for the static HTML sites. I want Apache to run as the client (suexec?). Some of their stuff will be PHP apps and I'm under the impression I'll want to look at suphp as well then. So basically I want to look like a small version of a shared web hosting company. Considering how common those are I thought I'd easily find a nice current How-To guide on setting this all up but so far I've had very little luck. I suspect my search words are off. So the questions (feel free to answer any or all): Anyone have some solid links to current/modern guides that would help me set this all up? No, the apache documentation site is not a guide ;-) Since I have a mix of static sites and PHP apps do I want/need both suexec and suphp installed? If so, does that introduce any challenges I should be aware of? Should I be looking at other options instead of suexec and suphp? I plan to give the end users SSH, SFTP or SCP access to their stuff (if that affects anything). Thanks in advance for your help.

  Read the article

• MySQL 5.6 won't start on OS X - ambiguous option

  - by MaticPetek

  I would like to try MySQL 5.6 on my machine, but I cannot start it. I always get an error : [ERROR] /usr/local/mysql-5.6.5-m8-osx10.6-x86/bin/mysqld: ambiguous option '--log=/var/log/mysqld.log' (log-bin, log_slave_updates) my.cnf: [mysqld]<br/> pid-file=/usr/local/mysql-5.6.5-m8-osx10.6-x86/mysql.pid<br/> log-error=/usr/local/mysql-5.6.5-m8-osx10.6-x86/data/mysql-error.log<br/> log-slow-queries=/usr/local/mysql-5.6.5-m8-osx10.6-x86/data/mysql-slowquery.log<br/> log-bin=/usr/local/mysql-5.6.5-m8-osx10.6-x86/data/mysql-bin.log<br/> general_log_file=/usr/local/mysql-5.6.5-m8-osx10.6-x86/data/mysql-general_log_file.log<br/> log=/usr/local/mysql-5.6.5-m8-osx10.6-x86/data/mysql.log<br/> I try to set "log" and "log-bin" paramether in my.cnf file and also as start parameters for mysqld, but with no luck. Any idea what I can do? Thank you. My environment: OS X 10.6.8 mysql-5.6.5-m8-osx10.6-x86 (not _x64 version) Note: I'm also running Mysql 5.5 on this machine (different port and socket). I also try to stop this instance but I get the some error.

  Read the article

• Mirror a Dropbox repository in Sharepoint and restrict access

  - by Dan Robson

  I'm looking for an elegant way to solve the following problem: My development team uses Dropbox for sharing documents amongst our immediate group. We'd like to put some of those documents into a SharePoint repository for the larger group to be able to access, as granting Dropbox access to the group at large is not ideal. However, we'd like to continue to be able to propagate changes to the SharePoint site simply by updating the files in Dropbox on our local client machines, and also vice versa - users granted access on SharePoint that update files in that workspace should be able to save their files and the changes should appear automatically on our client PC's. I've already done the organization of the folders so that in Dropbox, there exists a SharePoint folder that looks something like this: SharePoint ----Team --------Restricted Access Folders ----Organization --------Open Access Folders The Dropbox master account and the SharePoint master account are both set up on my file server. Unfortunately, Dropbox doesn't seem to allow syncing of folders anywhere above the \Dropbox\ part of the file system's hierarchy - or all I would have to do is find where the Sharepoint repository is maintained locally, and I'd be golden. So it seems I have to do some sort of 2-way synchronization between the Dropbox folder on the file server and the SharePoint folder on the file server. I messed around with Microsoft SyncToy, but it seems to be lacking in the area of real-time updating - and as much as I love rsync, I've had nothing but bad luck with it on Windows, and again, it has to be kicked off manually or through Task Scheduler - and I just have a feeling if I go down that route, it's only a matter of time before I get conflicts all over the place in either Dropbox, SharePoint, or both. I really want something that's going to watch both folders, and when one item changes, the other automatically updates in "real-time". It's quite possible I'm going down the entirely wrong route, which is why I'm asking the question. For simplicity's sake, I'll restate the goal: To be able to update Dropbox and have it viewable on the SharePoint site, or to update the SharePoint site and have it viewable in Dropbox. And since I'm a SharePoint noob, I'll also need help hiding the "Team" subfolder from everyone not in a specific group in AD.

  Read the article

• nginx not serving admin static files?

  - by toto_tico

  First, I want to clarify that this error is just for the admin static files. This means my problem is specific just to the static files that corresponds to the Django admin. The rest of the static files are working perfect. Basically my problem is that for some reason I cannot access those admin static files with the ngix server. It works perfect with the micro server of Django and the collect static is doing its job. This means it is putting the files on the expected place in the static folder. The urls are correct but I cannot even access the admin static files directly, but the others I can. So, for example, I am able to access this url (copying it in the browser): myserver.com:8080/static/css/base/base.css but i am not able to access this other url (copying it in the browser): myserver.com:8080/static/admin/css/admin.css I also tried to copy the admin/ directory structure into other_admin_directory_name/. Then I can access myserver.com:8080/static/other_admin_directory_name/css/admin.css Then, it works. So, I checked permissions and everything is fine. I tried to change ADMIN_MEDIA_PREFIX = '/static/admin/' to ADMIN_MEDIA_PREFIX = '/static/other_admin_directory_name/', it doesn't work. This a mistery in itself that I am exploring but still no luck. Finally, and it seems to be an important clue: I tried to copy the admin/ directory structure into admin_and_then_any_suffix/. Then I cannot access myserver.com:8080/static/admin_and_then_any_suffix//css/admin.css So, if the name of the directory starts with admin (for example administration or admin2) it doesn't work. * added thanks to sarnold observation ** the problem seems to be in the nginx configuration file /etc/nginx/sites-available/mysite location /static/admin { alias /home/vl3/.virtualenvs/vl3/lib/python2.7/site-packages/django/contrib/admin/media/; }

  Read the article

• Is something infecting my Google searches?

  - by hippietrail

  I starting doing some experimentation toward making a browser userscript for Google searches and when opening the JavaScript console noticed something that strikes me as very fishy: The page at https://www.google.com.au/search?oq=XYZ&sourceid=chrome&ie=UTF-8&q=XYZ displayed insecure content from http://50.116.62.47/js/chromeServerV45.js. The page at about:blank displayed insecure content from http://96.126.107.154/amz/google.php?callback=a&q=XYZ&country=US. (XYZ is a placeholder for whatever the search terms really was.) Is it likely that I've picked something like a drive-by browser infection? I've tried all kinds of searches for these URLs and other keywords but I've had no luck finding anything conclusive about whether they're malicious or what they are: 50.116.62.47 chromeServerV45.js 96.126.107.154 amz/google.php The only extensions I have installed are either widely used or written by myself. But something else is strange and I'm not sure if it's just a coincidence. I updated my Windows Chrome browser today to version 23.0.1271.64 m and now my Extensions tab as well as my settings tab are blank, so I can't try disabling my extesions. Here's some discussion I've been able to find so far but not really understand and make sense of: for 96.126.107.154 : "anomalous-javascript-pt2"

  Read the article

• How to set up QoS on ADSL router (terracom) for prioritizing browsing

  - by DBZ_A

  I want to configure the ADSL router which connects 10+ machines to the internet. I want to give maximum priority to browsing (ports 80,443) and set low priority for bittorrent etc.(port 42180) I have been experimenting with settings , but with no luck. There are three settings which confuse me, along with my understanding. 802.1 Priority - Related to LAN level, possible values 0-7 , higher numbers means higher priority. 'Mark traffic priority' - clueless about this. IPP/DS - IP Precedence - possible values 0-7 ; 6 & 7 are reserved, so set 5 for highest priority. Or when using DSCP - set 46 for highest priority. Please help me in getting this done... Similer question for another model of router here , but with less number of confusing options :) How to configure QoS on home router Update: from discussion on another thread, QoS can control only upstream traffic (from router to the internet) , while this may in turn affect downstream traffic rate, there is no direct control over data coming into the router.

  Read the article

• Why doesn't my symbolic link work?

  - by orokusaki

  I'm trying to better understand symbolic links... and not having very much luck. This is my actual shell output with username/host changed: username@host:~$ mkdir actual username@host:~$ mkdir proper username@host:~$ touch actual/file-1.txt username@host:~$ echo "file 1" > actual/file-1.txt username@host:~$ touch actual/file-2.txt username@host:~$ echo "file 2" > actual/file-2.txt username@host:~$ ln -s actual/file-1.txt actual/file-2.txt proper username@host:~$ # Now, try to use the files through their links username@host:~$ cat proper/file-1.txt cat: proper/file-1.txt: No such file or directory username@host:~$ cat proper/file-2.txt cat: proper/file-2.txt: No such file or directory username@host:~$ # Check that actual files do in fact exist username@host:~$ cat actual/file-1.txt file 1 username@host:~$ cat actual/file-2.txt file 2 username@host:~$ # Remove the links and go home :( username@host:~$ rm proper/file-1.txt username@host:~$ rm proper/file-2.txt I thought that a symbolic link was supposed to operate transparently, in the sense that you could operate on the file that it points to as if you were accessing the file directly (except of course in the case of rm where of course the link is simply removed).

  Read the article

• Strange ASP.NET Queue Performance Counters Behavior?

  - by LemurTech

  We have an ASP.NET 2.0 site running in classic mode. I am seeing very strange behavior in the performance counter values. Perhaps these are bugs (I've been all over Google trying to verify this, without much luck), or perhaps it is just my inexperience with monitoring these things. This PerfMon graph (http://imgur.com/Jv5io5J) represents a load test where I add up to 350 virtual users to the site, at a rate of about 1/sec, performing relatively simple page browsing. At the end of the test, I gradually taper off the number of users. This is a 4 CPU server. Machine.config settings for are at the defaults. The solid blue line is ASP.NET Apps v2.x\Requests Executing for the application in question. The profile makes perfect sense, with a quick ramp-up to 32 executing requests (minWorkerThreads x 4CPUs), followed by a slower ramp-up to 48 ((maxWorkerThreads - minWorkerThreads) x 4CPUs). The solid yellow line is ASP.NET v2.x\Requests Queued. Again, this makes sense: after the initial 32 request threads are activated, the queue begins to build as new thread initialization can't keep pace with incoming requests. But as executing requests reaches its highest possible value of 48, the counter for ASP.NET Apps v2.x\Requests Queued (green solid line) suddenly springs to life and maintains step with the yellow counter. As far as I can tell, and with no other apps running on the server, these two counters should have had the same values from the start. One other odd thing: The counter for ASP.NET v2.x\Request Wait Time (dotted yellow line) also does not spring to life until executing requests reaches 48. Shouldn't I be seeing values here from the moment ASP.NET v2.x\Requests Queued begins to build? And likewise, why would ASP.NET Apps v2.x\Request Execution Time (dotted blue) increase significantly only after that peak of 48 is reached? Shouldn't it ramp-up gradually along with queued requests?

  Read the article

• subdomains to different VMs on one IP address

  - by efbenson

  I have a setup at home with an ESXi server Freenas server and several win7 clients. I have a domain refactoringme.com I set the @ and WWW domain record to my (current) IP address. I then forwarded port 80 to my local win2k3 server on my Linksys router and used host name matching to run the 5 test sites I have. That all works. Now I want to use the turnkey machines and move to dedicated VM servers. One for a wiki one for SVN etc. So how do I get www.refactoringme.com to go to one internal IP address and wiki.refactoringme.com to different internal IP address, while they both use the same external IP address? I added the additional record for wiki to my domain and pointed it to @. I figured it had to be involving a real firewall. So I installed PFSense on a VM and set it on the DMZ on my Linksys. From this point I haven't had any luck. I thought that maybe it would be in the DNS Forwarder or maybe in the Rules sections but neither have worked. Am I doing it wrong or on the right track but am missing something. Thanks for all the help.

  Read the article

• New Computer won't boot up

  - by Reggie

  I brought new components and put a computer together. I installed win7(32bit) and everything was working as it should. However my case came with two USB3 front ports I could not connect because of motherboard did not support USB3, so I swapped out the board for a new motherboad with USB3 connection. Now I put everything back together but it won't bootup. "Memory Ok" light stay on. Motherboad LED is on. There is power, all fans are on but I got no display. There is no activity in back of the systems, none of the peripheral connection in the back are working. I have tried the following but to no avail. Reboot multiple times Unplug power and plug the power back Reset the CMOS battery..let it stays out for 10 minutes or more. Unplug all peripheral device but no luck Reset memory..... nothing happen The only thing I did not do was remove the cpu...but I unplug everything else. Please help, thank you.

  Read the article

• Http-Only cookies in WebLogic: what versions support them/how and why are they supported?

  - by John

  We want to make all cookies set by our webapp http-only. I only have a basic understanding of the benefits of doing this but I'm told by security people that it's a Good Thing (tm) Our app is running under JDK1.6.05 and WebLogic10.3.0 After way too much digging around Oracle's website for documentation, I've found good evidence that the first version of WebLogic to support http-only cookies is 10.3.1. By "support," I mean the cookie-http-only deployment-descriptor element. Before we go about upgrading, I'd be nice to have these questions answered: 1a) Is it accurate that WL10.3.1 is the first version to support http-only cookies and that we're out of luck with 10.3.0? 1b) If we do indeed need to upgrade, is there an easy to do so under Windows? I've heard people mention an "upgrade jar" that you just stick in the classpath but I can't find any mention of this by Oracle. Does an easy way exist, or do we need to do a full-install of the new version? 2) What does the cookie-http-only deployment-descriptor element do when enabled? Will it ensure all cookies set by the application have an http-only=true attribute? Will it do more or less? Is there anything I'll have to do programmatically? 3) Is there anything in general I should know about http-only cookies, getting my web app to take advantage of them, or other security concerns?

  Read the article

• corrupted, hidden, wireless network adapter from "Network Connections" in Windows 7

  - by srihari reddy

  The issue is that when I install a wireless network adapter on my Windows 7 Professional machine I have no connectivity, the system tray icon has a red X. First, I tried the obvious, install updated drivers from the manufacturer. When I did this, the Network Connections icon had gray bars and there was no connectivity. So I tried installling the network adapter on a different computer on the same network and I verified that it does work with no issues. Next, I ran scan disk with no issues. Next, I ran sfc as admin with no issues. At this point I turned to the router and turned SSID broadcast on but that didn't help. I turned MAC address filtering off at the router but that didn't help. Whenever I installed the original network adapter (a wireless N usb adapter with WPA2 TKIP+AES) it showed up as "Wireless Network Connection 2" with a grayed out icon and no connectivity. Lastly, I tried installing two different "verified working" usb wireless adapters on to the Windows 7 Pro machine. The results were the same "Wireless Network Connection 2" that had a green bar icon but no connectivity. I installed the manufacturers software and it indicated the NIC was not there even thought the driver installed successfully in Device Manager. I guess I should mention, I first tried (insanely in vain) to use the (worthless) Windows Network troubleshooter. The results were....drumroll please... There is a problem with the network adapter... well No Duh! Also, during all of this the network adapter is always showing as "Working Properly" in the properties dialogue of Device Manager for the wireless NIC. I checked for hidden devices in Device Manager but there were none. Here is my fundamental question that I've tried to find in the Windows 7 support center with no luck. How do I remove/delete/uninstall network adapters from the Windows 7 registry? in particular hidden, corrupted network adapters, that used to be working.

  Read the article

• Hostname and SSL (apache) issue on Debian

  - by user105566

  I have been trying to setup SSL virtual host ServerAdmin [email protected] ServerName moclm.tap.pt DocumentRoot /var/www/tapme/ <Directory /> Options FollowSymLinks AllowOverride All Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> <Directory /var/www/tapme/> Options -Indexes FollowSymLinks MultiViews AllowOverride All #Order allow,deny #allow from all </Directory> SSLEngine on SSLCertificateFile /etc/ssl/moclm.cer SSLCertificateKeyFile /etc/ssl/moclm.pem </VirtualHost> For some reason, the server automatically redirect to SSL (http:// to https://). The apache is not configured to redirect and application was working fine on port 80 only. I have no knowledge how the internal network works as i am working remotely. The SSL error logs show: [Tue Oct 02 22:40:32 2012] [error] Hostname linemnt01.tap.pt provided via SNI and hostname moclm.tap.pt provided via HTTP are different I thought may be the hostname has some issue and have changed the hostname of the server from "linemnt01.tap.pt" to "moclm.tap.pt" but the issue is still there. I am getting the following error on browser: Bad Request Your browser sent a request that this server could not understand. i have /etc/hosts: 127.0.0.1 localhost.localdomain localhost moclm.tap.pt moclm and openssl returns: openssl verify -CAfile cert-CA.cer moclm.cer moclm.tap.pt.cer: OK I have been trying to troubleshoot the issue but no luck. Need help Thanks

  Read the article

• Can't install SB750 RAID drivers in Windows 7 for two additional storage drives

  - by jf46

  Mobo: ASUS M4A79XTD, 790X/SB750 OS: Windows 7 x64 I currently have SATA 1-4 set to RAID and SATA 5-6 set to IDE. I have an SSD connected to SATA5 with Windows 7 installed on it, and that works fine. I also have configured a RAID 1 array of two 1TB HDDs, connected to SATA 1 and 2. These don't show up in Windows, and I'm having trouble getting the RAID driver installed. I even tried booting from the Windows DVD and repairing or installing Windows, but when I navigated to the relevant .sys files on my motherboard's driver CD, Windows setup told me that the files in question weren't relevant to my hardware. To be clear: I'm not trying to install Windows on a RAID. I have Windows installed on a separate disk on a separate SATA controller. I just want to get the SB750 RAID drivers installed so that the Windows disk utility can see my RAID 1 array, which is composed of two other disks. Do I need to wipe my SSD and reinstall Windows to get the RAID driver installed? That seems kind of ridiculous, and given what I described above, I'm not even sure it would work. Any help or guidance would be appreciated - thanks! Edit: Also, I've copied the driver files from the mobo CD into system32 and rebooted, no luck. Then I changed HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\iaStorV\Start from 3 to 0, and that didn't work either.

  Read the article

• SSL in IIS 7 on a subdomain in a web farm

  - by justjoshingyou

  I have been having one of the most frustrating days in my entire IT career. I am trying to install an SSL certificate on a subdomain in a web farm. http://shop.mydomain.com needs to ALWAYS be forced to https://shop.mydomain.com I have a temporary cert issued from verisign on shop.mydomain.com I have installed the cert on the server. The website for shop.mydomain.com is set as a host header in IIS with the DNS entry pointed to the same IP as mydomain.com - which is our load balancer. I actually have 2 load balancers (as needed by our ISP). One redirects all traffic on port 80 out to the different servers on port 80. The other pushes out port 443 to the servers on port 443. shop.mydomain.com is to be the only site protected by SSL at this time. When I add the binding and I navigate to https://shop.mydomain.com it pops up with a warning about the cert being invalid (assumed because this is a test cert), and then it sends the user to http. So, I checked the box "Require SSL and it redirects to http://shop.mydomain.com/default.aspx and displayes an ASP.NET 404 error message. (not the IIS 404 error) I tried removing the binding on the site to port 80 as well with no luck. I am nearly ready to crawl under my desk into the fetal position. How on earth do I make this work? I can't even get it to work on one machine, let alone in the load balanced environment.

  Read the article

• JBoss 5 on AIX 5.3

  - by jess

  I am a very newbie for AIX and system monitoring. Actually our application currently run production on jboss 5.1 in AIX 5.3. Please check below configuration & system settings. AIX system configuration OS Level 5.3.9.0 (oslevel -g) Physical Memory size 24GB (svmon -G) Page space 4GB (lsps -s) processors 3 cores, Processor Type: PowerPC_POWER6, Processor Clock Speed: 4704 MHz (prtconf | grep Processor) Java version JRE 1.6.0 IBM AIX build pap6460sr10fp1-20120321_01 (SR10 FP1) (java -fullversion) JBoss configuration JBoss 5.1/JBoss ESB 4.11 Hornetq messaging with consumer flow control java opts : -d64 -Xms2g -Xmx4g -XX:MaxPermSize=1024m Sometime we observe very strange behavior in the JBoss that freeze without any error logs. Also server log stop without any further trace. We also not able to get thread dump (kill -3) and its not generate at that point. (kill -3 xxxxx works in normal circumstances) Only option available for us was restart the jboss server and its seem all messages that were in queues during the freeze time process after restarting. We try tweak some of setting in JBoss hornetq, we though issue was there. Hornetq Stuck By Default. But we haven't any luck and also unable to isolate the issue in any point. We looking at tool like nmon for monitoring this but no clue is that good enough to do so. Please provide some point to investigate this issue. Thanks

  Read the article

• Computer causing WiFi interference?

  - by Mannimarco

  I came back from college and brought my desktop computer. Family recently switched to Verizon FIOS and got a new router because of it. Unfortunately, my connection to the new wifi network is awful, with the download speeds (tested through speedtest.net) fluctuating wildly and often dropping below 1.5 Mbps. A laptop in the same room gets 20 Mbps. I've tried a new wireless card, thinking that mine got damaged in the move home but no luck. Here's where it gets weird: if I place the laptop near the computer, the laptop's download speeds often suffer greatly. Pulling the laptop away always fixes this. So now I'm under the impression that there's something in the computer (which I built a year ago and has had 0 issues up to this point) is causing an insane amount of wireless interference. Also bizarre: the upload speeds seem unaffected by this problem. On the laptop and desktop, upload speeds are generally around 5 Mpbs. Any ideas as to what could be causing this and how to test said theories would be fantastic.

  Read the article

• java.lang.OutOfMemoryError: unable to create new native thread

  - by Brad

  I consistently get this exception when trying to run my Junit tests on my mac: java.lang.OutOfMemoryError: unable to create new native thread at java.lang.Thread.start0(Native Method) at java.lang.Thread.start(Thread.java:658) at java.util.concurrent.ThreadPoolExecutor.addIfUnderMaximumPoolSize(ThreadPoolExecutor.java:727) at java.util.concurrent.ThreadPoolExecutor.execute(ThreadPoolExecutor.java:657) at java.util.concurrent.AbstractExecutorService.submit(AbstractExecutorService.java:92) at com.google.appengine.tools.development.ApiProxyLocalImpl$PrivilegedApiAction.run(ApiProxyLocalImpl.java:197) at com.google.appengine.tools.development.ApiProxyLocalImpl$PrivilegedApiAction.run(ApiProxyLocalImpl.java:184) at java.security.AccessController.doPrivileged(Native Method) at com.google.appengine.tools.development.ApiProxyLocalImpl.doAsyncCall(ApiProxyLocalImpl.java:172) at com.google.appengine.tools.development.ApiProxyLocalImpl.makeAsyncCall(ApiProxyLocalImpl.java:138) The same set of unit tests pass perfectly fine on ubuntu and windows. Some information about my system resources on the mac: $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited file size (blocks, -f) unlimited max locked memory (kbytes, -l) unlimited max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 1 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) 266 virtual memory (kbytes, -v) unlimited $ java -version java version "1.6.0_24" Java(TM) SE Runtime Environment (build 1.6.0_24-b07-334-10M3326) Java HotSpot(TM) 64-Bit Server VM (build 19.1-b02-334, mixed mode) The reason I dont think this is an application issue is because the same tests pass in different environments. I have tried setting heap to 1024m, 512m and setting the stack to 64k and 128k (and each of these combinations) with no luck. My open files was originally 256 and I have bumped this to 1024. I have been googling around for a bit and all posts say to decrease heap size and increase stack size but that doesnt seem to help. Anyone have anymore ideas? EDIT: Here are is some environment information on my ubuntu box: $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 20 file size (blocks, -f) unlimited pending signals (-i) 16382 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) unlimited virtual memory (kbytes, -v) unlimited file locks (-x) unlimited $ java -version java version "1.6.0_24" Java(TM) SE Runtime Environment (build 1.6.0_24-b07) Java HotSpot(TM) 64-Bit Server VM (build 19.1-b02, mixed mode)

  Read the article

• No OS will boot, all freeze

  - by Gyan

  This is for a computer with the following configuration: Asus P5KPL-AM/PS motherboard Pentium D 820 (dual core 2.8 GHz) 1 x 2 GB DDR2-800 Transcend RAM 1 SATA2 Samsung 160 GB HDD 1 PATA LG CD/DVD Writer PS/2 generic Keyboard USB Razer mouse The computer was working fine till a month ago with a Hitachi HDD in place of the Samsung. But that drive died and I sent it in for warranty replacement. Since then and till last week, the computer had not been turned on. I then got hold of a spare but XPSP2-loaded Samsung drive from another computer and decided to get this computer temporarily running. However, when I tried to boot into XP, it didn't load. It got stuck at the first graphical screen. When trying Safe Mode, the file list would be updated up to diskio.sys and then freeze. If I tried to boot Kubuntu off a CD, I would get past the first menu, but then get stuck at the subsequent graphical interface in the loading process. A similar thing happend with a friend's Windows XP-on-a-pen-drive. I switched the RAM into the other slot, but no luck. Then I booted the Ultimate Boot CD and ran Memtest86+ and a couple of the bundled CPU stress tests but these detected no errors. Some searching on the Internet brought up the notion of the CPU failing to switch from "real" to "protected mode". I'm hoping to get a fix on what the problem is and what I can do about it. Edit: I've flashed to the latest BIOS, but that doesn't help. Also, Knoppix LiveCD also freezes. I notice that the LED in my mouse goes off at the time of freeze, but trying to boot without the mouse connected produces the same result.

  Read the article

< Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >