Search Results

Search found 2817 results on 113 pages for 'wiki'.

Page 87/113 | < Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >

• OpenVZ with brdiged interfaces and VLAN

  - by Deimosfr

  Hi, I've got a problem with OpenVZ with brdiged VLAN. Here is my configuration : +------+ +-------+ +-----------+ +---------+ br0 |VE101 | | | | OpenBSD |----->| Debian |------->| | | WAN |--->| Router | | OpenVZ | +------+ | | | Firewall |----->| br0 br1 | br1 +------+ +-------+ +-----------+ +---------+------->|VE102 | |br0 | | |VLAN br0.110 +------+ v +---------+ |VE103.110| +---------+ I can't make VLAN working on br0 (br0.110) and I would like to understand why. I don't have any switch so no problem with unmanageable switch. I've configured a VLAN interface on OpenBSD in /etc/hostname.vlan110 : inet 192.168.110.254 255.255.255.0 NONE vlan 110 vlandev sis1 And it seams working fine. I've also adapted my PF configuration to work with VLAN but I don't see any incoming traffic. On my Debian lenny, here is my interfaces configuration : # The loopback network interface auto lo iface lo inet loopback # br0 auto br0 iface br0 inet static address 192.168.100.1 netmask 255.255.255.0 gateway 192.168.100.254 network 192.168.100.0 broadcast 192.168.100.255 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off # VLAN 110 auto br0.110 iface br0.110 inet static address 192.168.110.1 netmask 255.255.255.0 network 192.168.110.0 gateway 192.168.110.254 broadcast 192.168.110.255 pre-up vconfig add br0 110 post-down vconfig rem br0.110 It looks like ok, but when I start my VE, here is the message : ... Configure veth devices: veth103.0 Adding interface veth103.0 to bridge br0.110 on CT0 for VE103 can't add veth103.0 to bridge br0.110: Operation not supported VE start in progress... So I've got one error here. I've followed this documentation http://wiki.openvz.org/VLAN but it doesn't work. I've certainly missed something but I don't know why. Someone could help me please ? Thanks

  Read the article

• iptables-restore: line 1 failed

  - by Doug

  Hello, I am new to servers, and I was following this guide and it failed on the first command instructed. Could anyone give me a hand? http://wiki.debian.org/iptables ~ZORO~:/etc# iptables-restore < /etc/iptables.test.rules iptables-restore: line 1 failed Edit: iptables.test.rules ~ZORO~:/etc# cat /etc/iptables.test.rules *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT -i ! lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You could modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections for script kiddies # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE -A INPUT -p tcp -m state --state NEW --dport 30000 -j ACCEPT # Now you should read up on iptables rules and consider whether ssh access # for everyone is really desired. Most likely you will only allow access from certain IPs. # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls (access via 'dmesg' command) -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy: -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT

  Read the article

• Different approaches to share files over local network

  - by exTyn

  I know, that I can use Google to find methods to share files over local network [1]. But, I have never shared files over local network, and I want to do this in a good, professional way. Also, this could be a good community wiki, I think. Well, what I am asking for, is: what are pros and cons of different methods to sharing files ofver local network? In my case, I need to share files between Linux & Win 7, and I want it to be secure (= without access for anyone else but me & people in my room). Another question (connected with above topic) is about playing music over the local network. Let's say, I live with 2 other guys in a room, one of us have speakers and we want to collaborate in creating playlists (e.g. everyone is choosing 3 songs to be played). Is it possible? How to do this? I am asking this question on SuperUser, because it (question) is connected with hardware & software (network, connecting computers, software for managing playlists in network etc.). I think it is most accurate place for such question (I have considered SO and SF). [1] And I have already done this! But, I do not have an experience in this field (sharing files over local network), do I am asking about pros and cons.

  Read the article

• Munin graphing by CGI

  - by Vaughn Hawk

  I have Munin working just fine, but any time I try to do cgi graphing - it just stops graphing... no errors in the log, nothing. I've followed the instructions here: http://munin-monitoring.org/wiki/CgiHowto - and it should be working - here's my munin.conf setup, at least the parts that matter: dbdir /var/lib/munin htmldir /var/www/munin logdir /var/log/munin rundir /var/run/munin tmpldir /etc/munin/templates graph_strategy cgi cgiurl /usr/lib/cgi-bin cgiurl_graph /cgi-bin/munin-cgi-graph And then the host info yada yada - graph_strategy cgi and cgrurl are commented out in munin.conf - that's because if I uncomment them, graphing stops working. Again, I get no errors in logs, just blank images where the graphs used to be. Comment out cgi? As soon as munin html runs again, everything is back to normal. I'm running the latest version of munin and munin-node - I've tried fastcgi and regular cgi - permissions for all of the directories involved are munin:www-data - and my httpd.conf file looks like this: ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory /usr/lib/cgi-bin/> AllowOverride None SetHandler fastcgi-script Options ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> <Location /cgi-bin/munin-cgi-graph> SetHandler fastcgi-script </Location> Does anyone have any ideas? Without this working, at least from what I understand, Munin just graphs stuff, even if no one is looking at them - you add 100 servers to graph, and this starts to become a problem. Hope someone has ran into this and can help me out. Thanks!

  Read the article

• Why won't my service start, and why doesn't upstart output any errors?

  - by Alex Waters

  I am trying to 'start gunicorn' as a service via upstart as user ale. I'm using gunicorn/flask on ubuntu 12.04 w/ init (upstart 1.5) Here is my /etc/init/gunicorn.conf setuid btw setgid flask script export HOME=/home/btw export WORKON_HOME=$HOME/.virtualenvs . $HOME/.virtualenvs/default/bin/activate cd $HOME/flask workon default gunicorn -c gunicorn.py bw:app end script It doesn't output anything other than gunicorn start/running, process 12992. If i then do 'status gunicorn' I get stop/waiting. any ideas on how to debug this? I tried following http://upstart.ubuntu.com/wiki/Debugging but it didn't help. If I do the following as user ale in the app's directory: 1. workon default 2. gunicorn -c gunicorn.py bw:app then Gunicorn runs fine. Here is ~/flask/gunicorn.py: bind = "0.0.0.0:8080" workers = 3 backlog = 2048 worker_class = "gevent" debug = True daemon = False pidfile ="/tmp/gunicorn.pid" log_level = "debug" accesslog = "/var/log/gunicorn/access.log" errorlog = "/var/log/gunicorn/error.log" user = "btw" group = "flask" Also, /var/log/error.log doesn't show anything new when I try to start the Gunicorn service. If I start it manually, it shows that the workers have been loaded, etc. Thanks for any help / suggestions!

  Read the article

• OpenVZ Can't initialize containers after install

  - by Tonino Jankov

  I have installed OpenVZ on centos 6 on a dedicated server. I followed quick installation guide on openvz wiki. After installing thru yum, I don't know why, but grub.conf wasn't automatically updated to accomodate new kernel, so I had to do it manually. I edited grub.conf, added openvz kernel and rebooted - it went fine. Server went up into openvz kernel and it worked, it started openvz service byitself. But after I created a container, added IP to it and attempted to start it, I couldn't. Here is the output from the shell: [root@cloud2 ~]# vzctl start 86 Starting container ... Container is mounted Container start failed (try to check kernel messages, e.g. "dmesg | tail") Container is unmounted [root@cloud2 ~]# dmesg | tail [ 1973.401596] CT: 86: failed to start with err=-105 [ 2107.113850] Failed to initialize the ICMP6 control socket (err -105). [ 2107.155523] CT: 86: stopped [ 2107.155543] CT: 86: failed to start with err=-105 [ 6348.282184] Failed to initialize the ICMP6 control socket (err -105). [ 6348.330348] CT: 86: stopped [ 6348.330361] CT: 86: failed to start with err=-105 [45184.024002] Failed to initialize the ICMP6 control socket (err -105). [45184.072086] CT: 86: stopped [45184.072099] CT: 86: failed to start with err=-105 [root@cloud2 ~]# I don't know what is wrong. I tried different templates, debian 6, centos 6, i386, amd64, but the issue is the same. What is the problem?

  Read the article

• Windows Server NTFS volume list file name encodings and any illegal file names

  - by benbradley

  I'm having to deal with a Windows Server (NTFS) file server and our backup application appears to be failing with certain files. According to this https://en.wikipedia.org/wiki/NTFS#Internals NTFS apparently supports file names encoded in UTF-16 but according to their support team, our backup application only supports UTF-8. I'd like to confirm whether this is actually the problem by seeing the file name encoding for myself. The files that are failing appear to be using plain English A-Z letters and other ASCII characters. No accents or non-English letters etc. I suppose even though the letters appear to be plain A-Z the file name could still be encoded in UTF-16. Does anyone know of a utility or script that can recursively go through all files in a directory and show the encoding of the file name? Then I could try renaming to UTF-8 to see if the backup can proceed. I'm not a Windows developer so can't write this up myself. Presumably the encoding of the file name should be stored in the FS somewhere and therefore it should be possible to expose this.

  Read the article

• Which is more secure: Tomcat standalone or Tomcat behind Apache?

  - by NoozNooz42

  This question is not about performance, nor about load-balancing, etc. Which would be more secure: running Tomcat in standalone mode or running Tomcat behind apache? The thing is, Tomcat is written in Java and hence it is pretty much immune to buffer overrun/overflow (unless a buffer overrun in a C-written lib used by Tomcat can be triggered, but they're rare [the last I remember was in zlib, many many moons ago] and one heck of a hack to actually exploit), which gets rid of a lot of potential exploits. This page: http://wiki.apache.org/tomcat/FAQ/Security has this to say: There have been no public cases of damage done to a company, organization, or individual due to a Tomcat security issue... there have been only theoretical vulnerabilities found. All of those were addressed even though there were no documented cases of actual exploitation of these vulnerabilities. This, combined with the fact that buffer overrun/overflow are pretty much non-existent in Java, makes me believe that Tomcat in standalone mode is pretty secure. In addition to that, I can install both Java and Tomcat on Linux without needing to be root. The only moment I need to be root is to set up a transparent port 8080 to port 80 forwarding (and 8443 to 443). Two iptables line as root, that's all root is needed for. (I don't know for Apache). Apache is much more used than Tomcat and definitely does not have a security track record as good as Tomcat. What would make Tomcat + Apache more secure? What would make Tomcat + Apache less secure? In short: which is more secure, Tomcat standalone or Tomcat with Apache? (remembering that performance aren't an issue here)

  Read the article

• Unable to use OpenGL or install nVidia driver on openSUSE 12.2

  - by djechelon

  I have an ASUS N76VZ laptop with 12.2 openSUSE and GeForce GT650M card. I found that KDE doesn't allow me to use OpenGL rendering. I tried to install nVidia's driver from script but once it writes the xorg.conf file I'm unable to boot desktop. I have the following errors in system log Oct 30 08:28:13 RAYNOR kdm[2727]: X server died during startup Oct 30 08:28:13 RAYNOR kdm[2727]: X server for display :0 cannot be started, session disabled I noticed that the /etc/X11/xorg.conf backup file was empty, so I renamed the new xorg.conf and left none: the desktop booted!!! How can I fix OpenGL rendering with or without driver installation? [Update]: Xorg.0.log says [ 1434.207] compiled for 4.0.2, module version = 1.0.0 [ 1434.207] Module class: X.Org Server Extension [ 1434.207] (II) NVIDIA GLX Module 304.60 Sun Oct 14 20:44:54 PDT 2012 [ 1434.207] (II) Loading extension GLX [ 1434.207] (II) LoadModule: "record" [ 1434.207] (II) Loading /usr/lib64/xorg/modules/extensions/librecord.so [ 1434.207] (II) Module record: vendor="X.Org Foundation" [ 1434.207] compiled for 1.12.3, module version = 1.13.0 [ 1434.207] Module class: X.Org Server Extension [ 1434.207] ABI class: X.Org Server Extension, version 6.0 [ 1434.207] (II) Loading extension RECORD [ 1434.207] (II) LoadModule: "dri" [ 1434.207] (II) Loading /usr/lib64/xorg/modules/extensions/libdri.so [ 1434.207] (II) Module dri: vendor="X.Org Foundation" [ 1434.207] compiled for 1.12.3, module version = 1.0.0 [ 1434.207] ABI class: X.Org Server Extension, version 6.0 [ 1434.207] (II) Loading extension XFree86-DRI [ 1434.207] (II) LoadModule: "nvidia" [ 1434.208] (II) Loading /usr/lib64/xorg/modules/drivers/nvidia_drv.so [ 1434.208] (II) Module nvidia: vendor="NVIDIA Corporation" [ 1434.208] compiled for 4.0.2, module version = 1.0.0 [ 1434.208] Module class: X.Org Video Driver [ 1434.208] (II) NVIDIA dlloader X Driver 304.60 Sun Oct 14 20:24:42 PDT 2012 [ 1434.208] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs [ 1434.208] (++) using VT number 8 [ 1434.320] (EE) No devices detected. [ 1434.320] Fatal server error: [ 1434.320] no screens found [ 1434.320] Please consult the The X.Org Foundation support at http://wiki.x.org for help.

  Read the article

• Gvim on Windows 7: ALT codes not working

  - by John Sonderson

  I would like to be able to enter ALT codes in Gvim on Windows 7 as documented on the following site: Alt Codes On Windows (Windows 7 in my case), to generate a character via an ALT code you make sure that the NumLock key on your keypad is toggled on, hold down the ALT key, enter the keycode on the numeric keypad, and then release the ALT key. However this does not work in Gvim on Windows (which ignores the fact that I am pressing the ALT key and just prints to entered keypad key directly onto the screen). How can I get these keystroke combinations to work in Gvim as well? Thanks. EDIT: As the answer below points out, the way to insert non-ASCII characters for which you do not have entries on your keyboard without changing the keyboard layout is as follows: Make sure you are in insert mode, and then type CTRL-V followed by the Unicode character code of interest, for instance: CTRL-V u00E0 (generates à) CTRL-V u00C8 (generates È) CTRL-V u00E8 (generates è) CTRL-V u00E9 (generates é) CTRL-V u00EC (generates ì) CTRL-V u00F2 (generates ò) etc... See for instance http://unicode-table.com/ for a full list of Unicode character codes. The following list of Unicode characters by language may also be useful: http://en.wikipedia.org/wiki/List_of_Unicode_characters In some cases such as this one, though, there might be an easier way to enter special characters (see :help digraphs and :digraphs). For example, while in insert mode you may be able to type the following: CTRL-K E! (yields É) CTRL-K a' (yields á) Note that as the following page shows: http://code.google.com/p/vim/source/browse/runtime/doc/digraph.txt Gvim 7.4 contains an even wider set of default digraphs than Gvim 7.3, thus providing convenience to an even broader set of languages. Regards.

  Read the article

• Problem with deploying django application on mod_wsgi

  - by Shehzad009

  Hello, I seem to have a problem deploying django with mod_wsgi. In the past I've used mod_python but I want to make the change. I have been using Graham Dumpleton notes here http://code.google.com/p/modwsgi/wiki/IntegrationWithDjango1, but it still seem to not work. I get a Internal Server Error. django.wsgi file: import os import sys sys.path.append('/var/www/html') sys.path.append('/var/www/html/c2duo_crm') os.environ['DJANGO_SETTINGS_MODULE'] = 'c2duo_crm.settings' import django.core.handlers.wsgi application = django.core.handlers.wsgi.WSGIHandler() WSGIScriptAlias / /var/www/html/c2duo_crm/apache/django.wsgi Apache httpd file: <Directory /var/www/html/c2duo_crm/apache> Order allow,deny Allow from all </Directory> In my apache error log, it says I have this error This is not all of it, but I've got the most important part: [Errno 13] Permission denied: '/.python-eggs' [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] The Python egg cache directory is currently set to: [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] /.python-eggs [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] Perhaps your account does not have write access to this directory? You can [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] change the cache directory by setting the PYTHON_EGG_CACHE environment [Thu Mar 03 14:59:25 2011] [error] [client 127.0.0.1] variable to point to an accessible directory.

  Read the article

• Nginx and automatic updates

  - by Desmond Hume

  I'm on Ubuntu 12.04.1 with unattended-upgrades configured for automatic security updates, and I installed Nginx by first adding deb http://nginx.org/packages/ubuntu/ lucid nginx deb-src http://nginx.org/packages/ubuntu/ lucid nginx to /etc/apt/sources.list file, just as was suggested by the official wiki, and then by sudo apt-get update sudo apt-get install nginx which installed Nginx with all the standard modules. But now I think I could make good use of one or two of the Nginx optional modules, like the gzip precompression module or some security-related one. So far, I see two ways of adding an optional module to Nginx, one is compiling and installing from the source code and the other is described in this article. So, which of the ways should I choose so that automatic updates still run for and apply to Nginx and its optional modules? Or should I create a cron job with a command/script specific for Nginx instead of using unattended-upgrades utility? Can I choose between volume updates and security-only updates to be automatically applied to the standard and optional modules? And finally, is there a possibility to automatically update Nginx's modules on the fly (without any connections having been dropped), like the documentation suggests it's possible with sudo kill -USR2 $( cat /run/nginx.pid ) P.S. Actually I'm not certain if unattended-upgrades utility would automatically update the standard modules in the first place, not enough time has passed since Nginx was installed to say for sure.

  Read the article

• How is made sure magnetic or electric fields from devices like transformers or fans close nearby do

  - by matnagel

  Fans and transformers which are inside the server case create magnetic and electric fields. Electric fields can be easily shielded, but what about magnetic fields, they can only be shielded with high cost materials like mu metal http://en.wikipedia.org/wiki/Mu-metal If a hard drive is installed too close to an intense transformer field, how is the magnetically stored information on the ferromagnetic surfaces of the disk kept safe? Even if drives are shielded, where are the limits? Is there some technical investigation or recommendation from manufacturers about this? (I never heard about something and never had any problem but I am interested in some facts. This is much preferred over what you believe or a habit you developed. Please try to give some solid infromation.) I have built and repaired many servers and sometimes I did put the harddrive on top of the power supply. Edit: This question is not about frequencies that could affect the drive via the power or data connectors of the drive, those are electronically decoupled and that's another question. Edit 2: The wikipedia page states that the motor inside the drive is shielded with mu metal. It is obvious that manufactureres have to take care of this. This question is about such influences from outside the drive.

  Read the article

• Controlling clone access to multiple mercurial repos served via hgwebdir.cgi

  - by chrislawlor

  I'm trying to host multiple hg repositories to use for my clients. I need to control access to each repository individually - not just push access, but clone as well. I've got an .htaccess set which requires authentication globally: AuthUserFile /path/to/hgweb.passwd AuthGroupFile /dev/null AuthName "Chris Lawlor Client Mercurial Repositories" AuthType Basic <Limit GET POST PUT> Require valid-user </Limit> <FilesMatch "\.(htaccess|passwd|config|bak)$"> Order Allow,Deny Deny from all </FilesMatch> Then in each repository, I've got a .hg/hgrc file requiring a valid user [web] allow_push = <comma seperated user list> This almost does what I need. The problem is that I need to add ALL my clients to hgweb.passwd, which gives them clone access to ALL of the repositories. The only solution I can think of is to have another .htaccess and .passwd file in EACH repository. I don't really want to do that though, seems a little convoluted. I can already specify a list of authorized users for each repository in that repos' hgrc file with the allow_push setting. If only there were an allow_clone setting as well... All the documentation I've found for hgwebdir.cgi is incomplete. I've read: http://mercurial.selenic.com/wiki/HgWebDirStepByStep http://hgbook.red-bean.com/read/collaborating-with-other-people.html#sec:collab:cgi http://hgbook.red-bean.com/read/collaborating-with-other-people.html And others. I've yet to find a comprehensive list of hgrc settings. I guess this is as much an Apache question than a mercurial question. Unless I can find a better approach, I'll be going with a seperate .htaccess and .passwd file for each repo. This is a virtual host on Webfaction if it matters - set up roughly like this http://docs.webfaction.com/software/mercurial.html

  Read the article

• Use of backreferences in fail2ban filters possible?

  - by Izzy

  From time to time, I see collections of suspect "File not found" errors in my Apache logs, basically using the pattern File does not exist: /var/www/file, referer: http://my.server.com/file In human terms: The file was not found, though it referenced here itself. A clear hacking attempt, as that's hardly possible (and the REQUEST_URIs often enough suggest the same). In my eyes a clear case for fail2ban – if I could get backreferences to work here: failregex = ^%(_apache_error_client)s File does not exist: /var/www(.+), referer: http://.+\1$ (Justin Case: above examples assume the DIRECTORY_ROOT of that webserver being /var/www) I googled for hours, searched the fail2ban wiki up and down – but nowhere I could find a statement concerning backreferences in its filters. Are they not supported, or did I do it the wrong way? Any hints how to make it work (except from "dirty hacks" like first sending the request to another fake url using mod-rewrite, and then catching on that (if anyone is interested, I can elaborate on that approach in an answer), or doing something similar using mod-security)? as an entire log line was requested: [Fri Nov 08 14:57:28 2013] [error] [client 50.67.234.213] File does not exist: /var/www/text/files.htm++++++++++++++++++++++++++Result:+using+proxy+27.34.142.47:9090;+no+post+sending+forms+are+found;, referer: http://www.myserver.com/text/files.htm++++++++++++++++++++++++++Result:+using+proxy+27.34.142.47:9090;+no+post+sending+forms+are+found; (sorry, logs were just switched, so this long candidate was the only one left currently; minor adjustments were made for privacy reasons)

  Read the article

• OpenVZ with bridged interfaces and VLAN

  - by Deimosfr

  Hi, I've got a problem with OpenVZ with bridged VLAN. Here is my configuration: +------+ +-------+ +-----------+ +---------+ br0 |VE101 | | | | OpenBSD |----->| Debian |------->| | | WAN |--->| Router | | OpenVZ | +------+ | | | Firewall |----->| br0 br1 | br1 +------+ +-------+ +-----------+ +---------+------->|VE102 | |br0 | | |VLAN br0.110 +------+ v +---------+ |VE103.110| +---------+ I can't make VLAN work on br0 (br0.110) and I would like to understand why. I don't have any switch so no problem with unmanageable switch. I've configured a VLAN interface on OpenBSD in /etc/hostname.vlan110: inet 192.168.110.254 255.255.255.0 NONE vlan 110 vlandev sis1 And it seems to be working fine. I've also adapted my PF configuration to work with VLAN but I don't see any incoming traffic. On my Debian Lenny, here is my interfaces configuration : # The loopback network interface auto lo iface lo inet loopback # br0 auto br0 iface br0 inet static address 192.168.100.1 netmask 255.255.255.0 gateway 192.168.100.254 network 192.168.100.0 broadcast 192.168.100.255 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off # VLAN 110 auto br0.110 iface br0.110 inet static address 192.168.110.1 netmask 255.255.255.0 network 192.168.110.0 gateway 192.168.110.254 broadcast 192.168.110.255 pre-up vconfig add br0 110 post-down vconfig rem br0.110 It looks OK, but when I start my VE, here is the message: ... Configure veth devices: veth103.0 Adding interface veth103.0 to bridge br0.110 on CT0 for VE103 can't add veth103.0 to bridge br0.110: Operation not supported VE start in progress... So I've got one error here. I've followed this documentation http://wiki.openvz.org/VLAN but it doesn't work. I've certainly missed something but I don't know why. Someone could help me please? Thanks

  Read the article

• Backup Exec tape rotation guidelines

  - by HannesFostie

  Hi We use Backup Exec to take care of our backups for our data server, exchange server, and one more set of systems. Each of these 3 is being done on a separate "set" of tapes. Our goal is to be able to roll back a full 2 weeks, with 1 full backup each weekend and differential/incremental backups in between (the difference between the two in our case isn't very big, because the employees mostly use a very similar set of files throughout the week). While playing around with the settings on how to achieve this, we set the time for BE to keep the full backup to 14 days, but because we have too much data this would require manual intervention each time to erase a certain tape and use that. What I would like to know is what kind of guidelines, tricks, tips and general "stuff to think about" you keep in mind when designing your backup schedule. The type of backups (full/diff/incr) isn't of that much importance in our case as it's more or less set in stone. Made this community wiki as it's not a very specific question. Thanks in advance!

  Read the article

• Live Screencast under Linux

  - by OmnipotentEntity

  I was having some difficulty with running a Live Screencast under Linux. I've found jtvlc and tried using that, but whenever I use it the stream comes out either blank or lagged with extremely high latency. I have a fast internet connection and a fast computer, but am I perhaps taxing it too much? Any ideas on what I could possibly be doing wrong? # 1. Get an account on http://www.justin.tv/ # 2. Copy streaming key from: http://www.justin.tv/broadcast/adv_other # 2. Install VLC: http://www.videolan.org/vlc/ # 3. Get Win/Mac/Lin Stream Client: \ # http://apiwiki.justin.tv/mediawiki/index.php/Linux_Broadcasting_API # 4. Adjust the vlc parameters to your liking and run VLC like this #!/bin/bash cvlc screen:// --input-slave=pulse:// \ --screen-width 1920 \ --screen-height 1080 \ --screen-fps 5 \ -v input_stream \ --sout='#duplicate{ dst="transcode{ scale=1, venc=x264{ keyint=60 }, vcodec=h264, vb=600, acodec=mp4a, ab=32, channels=2, samplerate=22050 } :rtp{dst=127.0.0.1,port=1234,sdp=file:///tmp/vlc.sdp} "}' \ --sout-transcode-threads=4 & sleep 2 # 5. Run JTVLC to stream like this: ./jtvlc/jtvlc omnipotententity censored /tmp/vlc.sdp # Notes: #- If you want to see what you're about to stream add 'dst=display, ' # before 'dst="transcode[' # More about the VLC parameters: http://wiki.videolan.org/Documentation:Modules/screen

  Read the article

• KeePass lost password and/or corruption due to Dropbox/KeePassX

  - by GummiV

  I started using Keepass about a month ago to hold my passwords and online accounts info. Everything was stored in a single .kdb file, only protected with a password. I'm using Windows 7. Now Keepass can't open my .kdb file with the error "Invalid/wrong key". I'm fairly confident I have the right password. Altough I might have mixed up a few letters I've tried about two dozen different combinations to minimize that possibility - but can't rule it out though. My guess is however that the .kdb file got corrupted, either due to Dropbox syncing (only using it on one computer though) or because I edited the file using KeePassX on Ubuntu (dual boot on the same computer, accessing a mounted Win7 NTFS partition), or possibly a combination of both. I have tried restoring older versions(even the original one) from Dropbox and trying out all possible passwords without any luck. (which does seem to rule out KeePassX as the culprit, since oldest copies are before I edited the file from Ubuntu) I have tried opening the file with the "Repair KeePass Database file" which always gives the "0xA Invalid/corrupt file structure" (the same error for when a wrong password is typed). I was wondering if there was any way for me to salvage my hard-gathered data. I know generally that brute force cracking is not feasible, but since I can remember probably more than half of the usernames/passwords, any maybe the fact that one of them does come up fairly often (my go-to pass for trivial stuff), that might simplify the brute force process to a doable time frame. Maybe the brute-force thing might incorporate the fact that I know the password length and what characters it's made from. (If we assume corruption, not a password-blackout on my part) I could do some programming if there are any libraries or routines that I could use. Other people seem to have had a similar probem http://forums.dropbox.com/topic.php?id=6199 http://forums.dropbox.com/topic.php?id=9139 http://www.keepassx.org/forum/viewtopic.php?t=1967&f=1 So hopefully this question will become a suitible resource for people when searching the web. Feel free to tell me if you think this should rather be a community wiki.

  Read the article

• Configuring wsgi for a simple Python based site

  - by jbbarnes

  I have an Ubuntu 10.04 server that already has apache and wsgi working. I also have a python script that works just fine using the make_server command: if __name__ == '__main__': from wsgiref.simple_server import make_server srv = make_server('', 8080, display_status) srv.serve_forever() Now I would like to have the page always active without having to run the script manually. I looked at what Moin is doing. I found these lines in apache2.conf: WSGIScriptAlias /wiki /usr/local/share/moin/moin.wsgi WSGIDaemonProcess moin user=www-data group=www-data processes=5 threads=10 maximum-requests=1000 umask=0007 WSGIProcessGroup moin And moin.wsgi is as listed: import sys, os sys.path.insert(0, '/usr/local/share/moin') from MoinMoin.web.serving import make_application application = make_application(shared=True) QUESTION: Can I create a similar section in apache2.conf pointing to another wsgi file? Like this: WSGIScriptAlias /status /mypath/status.wsgi WSGIDaemonProcess status user=www-data group=www-data processes=5 threads=10 maximum-requests=1000 umask=0007 WSGIProcessGroup status And if so, what is required to convert my simple_server script into a daemonized process? Most of the information I find about wsgi is related to using it with frameworks like Django. I haven't found a simple howto detailing how to make this work. Thanks.

  Read the article

• Nginx map module 301 redirecting

  - by Reinier Korth

  I've rebuild my website in Ruby on Rails and now I want to 301 redirect a lot of old urls using Nginx's http://wiki.nginx.org/HttpMapModule For some reason I can't get it to work. It works fine without the rewrite ^ $new permanent; line. Does anyone see what I'm missing? This my nginx.conf: server { server_name example.com; return 301 $scheme://www.example.com$request_uri; } # 301 redirect list map $uri $new { /test123 http://www.example.com/test123; /bla http://www.example.com/bladiebla; } server { server_name www.example.com; rewrite ^ $new permanent; root example/public; location ^~ /assets/ { gzip_static on; expires max; add_header Cache-Control public; } try_files $uri/index.html $uri @unicorn; location @unicorn { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; proxy_pass http://unicorn-<%= application %>; } error_page 500 502 503 504 /500.html; client_max_body_size 4G; keepalive_timeout 10; }

  Read the article

• Graphite not running

  - by River

  I'm currently trying to install graphite 0.9.9 on a gentoo box using these instructions from the graphite wiki. Essentially, it fronts graphite using apache and mod_wsgi. Everything seems to have gone well, except that apache / the graphite webapp never seem to return a response to the web browser (the browser continuously waits to load the page). I've turned on the graphite debug info, but the only message in the log files is this, repeated over and over again in info.log (with the pid always changing): Thu Feb 23 01:59:38 2012 :: graphite.wsgi - pid 4810 - reloading search index These instructions have worked for me before to set up graphite on an Ubuntu machine. I suspect that mod_wsgi is dying, but I have confirmed that mod_wsgi works fine when not serving the graphite webapp. This is what my graphite.conf vhost file looks like: WSGISocketPrefix /etc/httpd/wsgi/ <VirtualHost *:80> ServerName # Server name DocumentRoot "/opt/graphite/webapp" ErrorLog /opt/graphite/storage/log/webapp/error.log CustomLog /opt/graphite/storage/log/webapp/access.log common # I've found that an equal number of processes & threads tends # to show the best performance for Graphite (ymmv). WSGIDaemonProcess graphite processes=5 threads=5 display-name='%{GROUP}' inactivity-timeout=120 WSGIProcessGroup graphite WSGIApplicationGroup %{GLOBAL} WSGIImportScript /opt/graphite/conf/graphite.wsgi process-group=graphite application-group=%{GLOBAL} WSGIScriptAlias / /opt/graphite/conf/graphite.wsgi Alias /content/ /opt/graphite/webapp/content/ <Location "/content/"> SetHandler None </Location> # XXX In order for the django admin site media to work you # must change @DJANGO_ROOT@ to be the path to your django # installation, which is probably something like: # /usr/lib/python2.6/site-packages/django Alias /media/ "/usr/lib64/python2.6/site-packages/django/contrib/admin/media/" <Location "/media/"> SetHandler None </Location> # The graphite.wsgi file has to be accessible by apache. It won't # be visible to clients because of the DocumentRoot though. <Directory /opt/graphite/conf/> Order deny,allow Allow from all </Directory> </VirtualHost>

  Read the article

• How can i export a folder of Firefox Bookmarks into a text file

  - by Memor-X

  I want to clean up my bookmark folders by getting rid of duplicated/links. i have created a program which will import 2 text files which contains a URL like this File 1: http://www.google/com http://anime.stackexchange.com/ https://www.fanfiction.net/guidelines/ https://www.fanfiction.net/anime/Magical-Girl-Lyrical-Nanoha/?&srt=1&g1=2&lan=1&r=103&s=2 File 2: http://scifi.stackexchange.com/ http://scifi.stackexchange.com/questions/56142/why-didnt-dumbledore-just-hunt-voldemort-down http://anime.stackexchange.com/ http://scifi.stackexchange.com/questions/5650/how-can-the-doctor-be-poisoned the program compares the 2 lists and creates a single master list with duplicate URLs removed. Now i have a few Backup bookmark folders in Firefox which on occasion i'll bookmark all tabs into a new folder with the date of the backup before i close off tabs or do reset my PC. each folder can have between 1000-2000 bookmarks, sometimes there are a bunch of pages which keep getting bookmarked, ie, i have ~50 pages on the Magical Girl Lyrical Nanoha Wiki on different spells, character and terminology which i commonly look back on. I'd like to know how i can export a bookmark folder so i have a list of URLs similar to what i use in my program

  Read the article

• Running Flash on a headless Solaris box

  - by Marty Pitt

  Our build server is a Solaris box, and I'm trying to run a suite of FlexUnit tests as part of the automated build process. This works by compiling a swf movie with a suite of automated unit tests. The build script launches this movie, which automatically begins running the tests. Results of each test are sent back to the launching script across a port, and written out to a local xml file. Once the tests are completed, the movie closes down, and the build script interrogates the results to see if all the tests passed. The FlexUnit wiki provides information about how to to acheive this on a Unix server, by using Xvnc to provide a virtual space for the flash movie to run its tests in. I've provided this information through to our sys admin team, (along with the link to the article), and I've been told that because this is a Solaris box, we can't use that approach - Xvnc isn't supported on Solaris. Unfortunately, I know very little about servers, *nix vs Solaris, or Xvnc. Can someone please provide some advice about how we can achieve the same outcome on a Solaris box?

  Read the article

• Run GUI application via cronjob in Ubuntu?

  - by Christoffer

  Hi, I have a remote server running "Ubuntu 10.04 Desktop". From it I want to run a script that walks through a list of websites and captures screenshots of them. The script is working and thoroughly tested. When I SSH to the server with ssh -X user@ip-adress I can run my script by calling ./myscript.py and everything will work OK. I then modifed my crontab file and added... 59 17 * * * env DISPLAY=:0 /path/to/myscript.py ...as recommended by the Ubuntu WIKI. I can see in the /var/log/syslog that my cron job is started, but it doesn't capture any screenshots. When running env DISPLAY=:0 /path/to/myscript.py from the shell I get No protocol specified myscript.py: cannot connect to X server :0 If I ssh to the server without the -X option I only get the second row of the error: myscript.py: cannot connect to X server :0 What can I try now? More details I have run xhost +local: and checked the output of xhost to see that the option was set correctly. If I run ls /tmp/.X11-unix/ the output is X0 The server only has one screen. Thank you in advance!

  Read the article

< Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >