Search Results

Search found 2603 results on 105 pages for 'daily'.

Page 88/105 | < Previous Page | 84 85 86 87 88 89 90 91 92 93 94 95  | Next Page >

• Router startup problems

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the power off and on again it all works. I also have to restart my PC too in order for everything to work. How can I solve this problem? Just leave the router turned on all time? I prefer a daily IP switch, though. May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• Router startup problems

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the power off and on again it all works. I also have to restart my PC too in order for everything to work. How can I solve this problem? Just leave the router turned on all time? I prefer a daily IP switch, though. May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• SQL Server Offsite Backups

  - by Eric Maibach

  We have about !TB of SQL Server databases, and these databases generate about 200GB of data changes each day. Up to this point we have been doing Weekly full backups, daily diff backups, and hourly transaction log backups. The full and diff backups are backed up to tape and taken offsite each day. We have been trying to move away from tapes, and our IT department purchased a Barracuda Backup device that backups up data and then sends it offsite using our internet connection. I have been trying to get this to work for our SQL Server backups, and have ran into a number of problems. I normally like to just use SQL Server to perform backups instead of trying to use a agent, so that is what I tried first. However the Barracuda device was not able to dedup these files very well, so it ended up being to much data to try to send offsite and to archive. I then tried installing the Barracuda agent and using it to backup the SQL Server databases. However the problem I am having there is that on some of the database servers I also have files that need backed up, and I cannot find a way to create seperate backup schedules for the file backups and the SQL Server backups. Barracuda only does full or transaction log backups. So if I want to do hourly transaction log backups I end up doing a file system backup every hour (which is not good), or if I only schedule the backups to run once a night I either have to do a full backup every night, or only do a transaction backup once a day. None of these scenarios are good options. My question is, how is everyone else getting their large SQL Server database backups offsite. Are you just using tape, or have you found a offsite backup device that works well? Is anybody else using Barracuda to backup their SQL Server databases? If you do, then how do you have it setup?

  Read the article

• VPN Client solution

  - by realtek

  I have several VPN's that I need to establish on a daily basis but from multiple workstations. What I would like to do it have either a server or vpn router that can perform this connection itself and that I can then route traffic through this device or server depending on the subnet I am trying to reach. The issue is that I only use VPN Clients to connect, so I am basically trying to achieve almost a site to site VPN but by using basically a VPN Client type connection from my network. The main VPN Client I use is the Sonicwall Global VPN Client where I initially use a Preshared Key and then it always prompts me for a username and password (not RSA key). My question is, is there any type of linux distro or even a hardware vpn router that can do this and connect to a Sonicwall device as if it were a client? I have tried pfSense which is very good but it fails to connect, probably due to a mismatch of settings. I have tried many others. Even dd-wrt on my router but it does not support whatever protocol Sonicwall uses. (I thought L2TP/IPSec) but it appears it may not be that. Any advice would be great! The other other thing I have thought of that I have not tried yet is Windows Server Routing and Remote Access but I have a feeling that won't work either. Thanks

  Read the article

• I want my logs sent to my mail with logrotate

  - by lericson

  Not strictly a question about programming as such, more of a log handling question. Anyway. My company has multiple clients, and each of these clients have a set of logs that I'd rather much want to get sent to by e-mail to me. Now, another prerequisite is that they're hilighted by simple HTML. All that is very well, I've managed to make a hilighter for the given log types. So, what I do is I use logrotate's prerotate stuff to send the logs as an e-mail message. Example: /var/log/a.log /var/log/b.log { daily missingok copytruncate prerotate /usr/bin/python /home/foo/hilight_logs /var/log/{a,b}.log | /usr/sbin/sendmail -FLog\ mailer [email protected] [email protected] endscript } The problem with this approach is basically that logrotate sucks: it'll run the command for every log file specified in the specifier, and to my knowledge there's no way to know which of the log files is being handled. (Which wouldn't really help anyway.) Short of repeating the exact same logrotate up to 10 times on different machines, the only thing I can do is just to get bogged down with log spam every night. And I grew tired of it today, so I ask.

  Read the article

• Why does this rsnapshot exclude not work?

  - by bstpierre

  Rsnapshot passes excludes directly to rsync, but rsync's behavior appears inconsistent. I've simplified my rsnapshot backup test to the following directory tree (this tree will be backed up): gorilla:~# find /tmp/snaptest -exec file {} \; /tmp/snaptest: directory /tmp/snaptest/SKIPTHIS: directory /tmp/snaptest/SKIPTHIS/xyz: directory /tmp/snaptest/SKIPTHIS/xyz/testing: ASCII text /tmp/snaptest/SKIPTHIS/bar: ASCII text /tmp/snaptest/SKIPTHIS/foo: ASCII text /tmp/snaptest/SKIPTHIS.txt: ASCII text My config file: config_version 1.2 snapshot_root /tmp/backup-media no_create_root 1 cmd_cp /bin/cp cmd_rm /bin/rm cmd_rsync /usr/bin/rsync cmd_ssh /usr/bin/ssh cmd_logger /usr/bin/logger cmd_du /usr/bin/du interval hourly 6 interval daily 7 interval weekly 4 interval monthly 3 verbose 3 loglevel 3 logfile /media/maxtor-one-touch/rsnapshot.log lockfile /media/maxtor-one-touch/backups/.rsnapshot.pid rsync_short_args -a rsync_long_args --delete --numeric-ids --relative --delete-excluded exclude "SKIPTHIS/**" link_dest 1 backup /tmp/snaptest snaptest The result: gorilla:~# rsnapshot -c /tmp/snaptest.conf hourly echo 12638 > /media/maxtor-one-touch/backups/.rsnapshot.pid mkdir -m 0755 -p /tmp/backup-media/hourly.0/ /usr/bin/rsync -a --delete --numeric-ids --relative --delete-excluded \ --exclude="SKIPTHIS/**" /tmp/snaptest \ /tmp/backup-media/hourly.0/snaptest touch /tmp/backup-media/hourly.0/ rm -f /media/maxtor-one-touch/backups/.rsnapshot.pid gorilla:~# find /tmp/backup-media/ -exec file {} \; /tmp/backup-media/: directory /tmp/backup-media/hourly.0: directory /tmp/backup-media/hourly.0/snaptest: directory /tmp/backup-media/hourly.0/snaptest/tmp: sticky directory /tmp/backup-media/hourly.0/snaptest/tmp/snaptest: directory /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS: directory /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS/xyz: directory /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS/xyz/testing: ASCII text /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS/bar: ASCII text /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS/foo: ASCII text /tmp/backup-media/hourly.0/snaptest/tmp/snaptest/SKIPTHIS.txt: ASCII text My confusion stems from the fact that if I copy-paste the rsync command echoed by rsnapshot, the SKIPTHIS directory is excluded! (I've tested with various other SKIPTHIS patterns with the same results.) Any idea what's going on?

  Read the article

• RAID6 mdraid -> LVM -> EXT4 root with GRUB2?

  - by Rotonen

  2012-03-31 Debian Wheezy daily build in VirtualBox 4.1.2, 6 disk devices. My steps to reproduce so far: Setup one partition, using the entire disk, as a physical volume for RAID, per disk Setup a single RAID6 mdraid array out of all of those Use the resulting md0 as the only physical volume for the volume group Setup your logical volumes, filesystems and mount points as you wish Install your system Both / and /boot will be in this stack. I've chosen EXT4 as my filesystem for this setup. I can get as far as GRUB2 rescue console, which can see the mdraid, the volume group and the LVM logical volumes (all named appropriately on all levels) on it, but I cannot ls the filesystem contents of any of those and I cannot boot from them. As far as I can see from the documentation the version of GRUB2 shipped there should handle all of this gracefully. http://packages.debian.org/wheezy/grub-pc (1.99-17 at the time of writing.) It is loading the ext2, raid, raid6rec, dosmbr (this one is in the list of modules once per disk) and lvm modules according to the generated grub.cfg file. Also it is defining the list of modules to be loaded twice in the generated grub.cfg file and according to quick Googling around this seems to be the norm and OK for GRUB2. How to get further by getting GRUB2 to actually be able to read the content of the filesystems and boot the system? What am I wrong about in my assumptions of functionality here? EDIT (2012-04-01) My generated grub.cfg: http://pastie.org/3708436 It seems it first makes my /usr logical volume the root and that might be source of the failure? A grub-mkconfig bug? Or is it supposed to get access to stuff from /usr before / and /boot? /boot is on / for me - no separate boot logical volume.

  Read the article

• Backing up large network (~200 clients) -- Enough Bandwidth?

  - by mtkoan

  My company wants to institute a backup plan for all of the clients on our network, which is about 200. We back up our servers and SQL databases regularly, but its been our policy to not backup individuals. What is most critical for people is their Documents and PST files in Outlook. PST files can be very large, and most people's are ~1-1.5 GB around here. So with PST files alone that is 200-300 GB of data needing to be transferred daily to a sever for backup. Or compressing first, then transferring, but many of the machines are VERY old and such a task would grind their computer to a halt. Isn't this the reason networks use things like VMware -- to reduce network traffic and streamline backups? Or is this only to reduce hardware costs? Would this much network traffic everyday drastically slow down our network? Enough to the point we'd have to mandate it to be done at night only? Or could we stagger then through out the day? Really appreciate any input, thank you.

  Read the article

• Emptying Windows temp folder is a good idea?

  - by Siva Charan

  Am using DELL Inspiron with Windows 7. As far as I know emptying the windows temp folder would be good. But I faced a strange behaviour around 8 months back, when I clear my windows temp folder. The next day onwards, my laptop starting displaying daily one or other errors and one day OS got crashed. Till now I am not sure whether OS got crashed due to clearing the windows temp folder or something else is problem. Here Windows temp folder mean "C:\Windows\Temp" This is the behind the story. Today, this temp folder "C:\Windows\Temp" contains 102 GB Most of the space occupied by the files starts with etilqs_*.*. I came to know that these files are generated due to WD SmartWare. Now my problem is:- Actually I want clean up this folder, since it occupies lot of space. If I clean up "C:\Windows\Temp" folder, will my laptop face the same kind of problem which I faced earlier OR Any new problems will occur? Please suggest me a good solution.

  Read the article

• BIND returns serverfail when querying for its authoriative domain

  - by estol

  Hi there Serverfault folks! First of all: sorry about the title, I had some problem coming up with the proper title. I have a little home server set up, for internet sharing, samba, basic http, dlna mediaserver and what not, and I happend to have a domain at hand, so I thought why not direct it to this computer? I have a BIND 9.8.0 installed, and - afaik - configured it properly. For a few days, the public view did not worked, and I really did not cared, since the local view worked. But now suddenly, even the local view fails. If I try to query the nameserver for anything in my domain, it returns the following error: $ nslookup andromeda.dafaces.com ;; Got SERVFAIL reply from ::1, trying next server ;; Got SERVFAIL reply from ::1, trying next server Server: 127.0.0.1 Address: 127.0.0.1#53 ** server can't find andromeda.dafaces.com.dafaces.com: SERVFAIL Also, the public view points to the old ip address of the domain, probably because of the same error. Some information about the system: $ uname -a Linux tressis 2.6.37-ARCH #1 SMP PREEMPT Tue Mar 15 09:21:17 CET 2011 x86_64 AMD Athlon(tm) 64 X2 Dual Core Processor 5000+ AuthenticAMD GNU/Linux $ named -v BIND 9.8.0 And the named.conf file: # cat /etc/named.conf // // /etc/named.conf // include "/etc/rndc.key"; #controls { # inet 127.0.0.1 allow {localhost; } keys { "dnskulcs"; }; #}; options { directory "/var/named"; pid-file "/var/run/named/named.pid"; auth-nxdomain yes; datasize default; // Uncomment these to enable IPv6 connections support // IPv4 will still work: listen-on-v6 { any; }; listen-on { any; }; // Add this for no IPv4: // listen-on { none; }; // Default security settings. // allow-recursion { 127.0.0.1; ::1; 192.168.1.0/24; }; // allow-recursion { any; }; allow-query { any; }; allow-transfer { 127.0.0.1; ::1; 92.243.14.172; 87.98.164.164; 88.191.64.64; }; allow-update { key "dnskulcs"; }; version none; hostname none; server-id none; zone-statistics yes; forwarders { 213.46.246.53; 213.26.246.54; 8.8.8.8; 8.8.4.4; 192.188.242.65; 193.227.196.3; 2001:470:20::2; }; }; view "local" { match-clients { 192.168.1.0/24; 127.0.0.1; ::1; fec0:0:0:ffff::/64; }; recursion yes; zone "localhost" IN { type master; file "localhost.zone"; allow-transfer { any; }; }; zone "0.0.127.in-addr.arpa" IN { type master; file "127.0.0.zone"; allow-transfer { any; }; }; zone "." IN { type hint; file "root.hint"; }; zone "dafaces.com" IN { type master; file "internal/dafaces.com.fw"; allow-update { key "dnskulcs"; }; }; zone "1.168.192.in-addr.arpa" IN { type master; file "internal/dafaces.com.rev"; allow-update { key "dnskulcs"; }; }; }; view "public" { match-clients { any;}; recursion no; zone "dafaces.com" IN { type master; file "external/dafaces.com.fw"; allow-transfer { 87.98.164.164; 195.234.42.1; 88.191.64.64; }; }; }; //zone "example.org" IN { // type slave; // file "example.zone"; // masters { // 192.168.1.100; // }; // allow-query { any; }; // allow-transfer { any; }; //}; logging { channel xfer-log { file "/var/log/named.log"; print-category yes; print-severity yes; print-time yes; severity info; }; category xfer-in { xfer-log; }; category xfer-out { xfer-log; }; category notify { xfer-log; }; }; All help would be highly appreciated! EDIT: Zone files: # cat /var/named/internal/dafaces.com.fw $ORIGIN . $TTL 3600 ; 1 hour dafaces.com IN SOA tressis.dafaces.com. postmaster.dafaces.com. ( 2011032201 ; serial 28800 ; refresh (8 hours) 7200 ; retry (2 hours) 2419200 ; expire (4 weeks) 3600 ; minimum (1 hour) ) NS tressis.dafaces.com. A 192.168.1.1 MX 10 mail.dafaces.com. $ORIGIN _tcp.dafaces.com. _http SRV 0 5 80 www.dafaces.com. _ssh SRV 0 5 22 tressis.dafaces.com. $ORIGIN dafaces.com. acrisius A 192.168.1.230 andromeda A 192.168.1.7 andromeda-win7 CNAME andromeda aspasia A 192.168.1.233 athena A 192.168.1.232 callisto A 192.168.1.102 db A 192.168.1.1 management A 192.168.1.1 ; web management for the router functions haley A 192.168.1.5 hoth A 192.168.1.101 mail A 192.168.1.1 satelite A 192.168.1.20 sony-player A 192.168.1.103 TXT "310f16de2d2712dfc4ae6e5c54f60f828e" torrent A 192.168.1.1 tracker A 192.168.1.1 tressis A 192.168.1.1 www A 192.168.1.1 zeus A 192.168.1.231 and # cat /var/named/external/dafaces.com.fw $ORIGIN . $TTL 3600 dafaces.com IN SOA ns.dafaces.com. postmaster.dafaces.com. ( 2011032405; serial 28800; refresh 7200; retry 2419200; expire 3600; minimum ) NS ns.dafaces.com. NS ns0.xname.org. NS ns1.xname.org. NS ns2.xname.org. A 89.135.129.37 MX 10 mail.dafaces.com. $ORIGIN dafaces.com. ;Szolgaltatasok _ssh._tcp SRV 0 5 22 tressis _http._tcp SRV 0 5 80 www ns A 89.135.129.37 hoth A 89.135.129.37 www A 89.135.129.37 mail A 89.135.129.37 db A 89.135.129.37 torrent A 89.135.129.37 tracker A 89.135.129.37 Edit: Ohh, hell I almost forgot. Since the node is connected to the internet via a residential connection, there is a possibility, that the public ipv4 address will change(but thank god, it is a very rare case), so I daily update the external IP address in the zone file with a shellscript: # cat /etc/cron.daily/dnsupdate #!/bin/sh FILE="/var/named/external/dafaces.com.fw" SERIAL=$(date +%Y%m%d05) PUBLIC_IP=$(ifconfig internet |sed -n "/inet addr:.*255.255.255.255/{s/.*inet addr://; s/ .*//; p}") cat $FILE | sed --posix 's/^.* serial$/\t\t\t\t\t'$SERIAL'; serial/' | sed --posix 's/[0-9]*\.[0-9]*\.[0-9]*\.[0-9]*/'$PUBLIC_IP'/' > /tmp/ujzona mv /tmp/ujzona $FILE /etc/rc.d/named reload

  Read the article

• System State Backup Retention Policies

  - by isoscelestriangle

  I was wondering if there was a general consensus on how long to keep system state backups. I am trying to reevaluate our current backup process, and trying to get a good handle on our current storage requirements. Our current setup involves tapes and sending backups offsite with Barracuda Networks. We have been doing our system state backups with Barracuda now, which does full backups daily, leaving our storage requirements growing quite quickly. My boss is a little too gung-ho with backups and wants our system states saved for quite a while. We currently have 5 days of nightlies, 5 weeklies, 3 monthlies, and so on. I think this is quite overkill for system state backups. My boss wants the ability to go back in time to find when an issue appeared, but I don't think that is practical. Many things change in the course of several months. I also think it would be hard not to notice problems with our DCs and other servers for several months. I would think that a previous week's snapshot and the current week's dailies would suffice. Any advice or reading you can point me to? Thanks!

  Read the article

• Symantec Backup Exec 12 Tape Alert.

  - by Adam

  Every day, I run 5 backups using 6 tapes. Each day, when I run the inventory, I get a tape alert Error. This occurs every day, on the same job. The error is: Job 'Inventory Daily ********' has reported Multiple Tape Alerts on server '******' Please refer to job log *****.xml for more information. When i look at the Job log, the Utility Job Information says: The device has reported the following TapeAlert diagnostic information Information- The library has been manually turned offline and is unavailable for use. Robotic library for device: PV132T 500 Warning - Library security has been compromised. Robotic Library for device: PV132T 500. Critical - The library has detected a inconsistency in its inventory. 1.Redo the library inventory to correct the inconsistency. 2. Restart the operation. Check the applications users manual or hardware users manual for specific instructions on redoing the library inventory. Roboric Library for Device PV132T 500. When I run the same inventory for a second time, the job completes successfully. I am using Symantec Backup Exec 12 running on Windows Server 2008. I am using a Dell Powervault 132T 500 tape drive. If anyone can help me on how to resolve this problem, it would be very much appreciated.

  Read the article

• Setting up MySQL Linux slave with a Windows master

  - by philwilks

  I'm running a MySQL 5.0 database server on Windows Server 2008. The total size of the database is about 1Gb. I make daily backups, but I'd like to step up to having a slave server for extra protection. My thinking was that I wouldn't need the expense of a Windows machine to do this, and a Linux "cloud server" from RackSpace would do the job well for quite a low cost. However I have little experience with Linux, so I have a few questions... Does this sound like a good idea? Is there anything wrong with linking Windows and Linux MySQL servers? Does Linux have the equivalent of Remote Desktop Connection? If so can I use this from a Windows machine? Would a particular Linux distro be well suited to this task? RackSpace offer ArchLinux, CentOS, Debian, Fedora and Ubuntu. My immediate thinking is to go with Ubuntu as I've heard it's more friendly for people coming from a Windows background. Any comments you have would be very appreciated! Phil

  Read the article

• checksecurity / setuid changes, is this a bug or did somebody break in?

  - by Fabian Zeindl

  I received a mail by checksecurity from my ubuntu 12.04 server with the following content: --- setuid.today 2012-06-03 06:48:09.892436281 +0200 +++ /var/log/setuid/setuid.new.tmp 2012-06-17 06:47:51.376597730 +0200 @@ -30,2 +30,2 @@ - 131904 4755 2 root root 71280 Wed May 16 07:23:08.0000000000 2012 ./usr/bin/sudo - 131904 4755 2 root root 71280 Wed May 16 07:23:08.0000000000 2012 ./usr/bin/sudoedit + 143967 4755 2 root root 71288 Fri Jun 1 05:53:44.0000000000 2012 ./usr/bin/sudo + 143967 4755 2 root root 71288 Fri Jun 1 05:53:44.0000000000 2012 ./usr/bin/sudoedit @@ -42 +42 @@ - 130507 666 1 root root 0 Sat Jun 2 18:04:57.0752979385 2012 ./var/spool/postfix/dev/urandom + 130507 666 1 root root 0 Mon Jun 11 08:47:16.0919802556 2012 ./var/spool/postfix/dev/urandom First i was worried, then i realized that the change was actually 2 weeks ago, i think there was a sudo-update back then. Since checksecurity runs in /etc/cron.daily i wondered why i only get that email now. I looked into /var/log/setuid/ and found the following files: total 32 -rw-r----- 1 root adm 816 Jun 17 06:47 setuid.changes -rw-r----- 1 root adm 228 Jun 3 06:48 setuid.changes.1.gz -rw-r----- 1 root adm 328 May 27 06:47 setuid.changes.2.gz -rw-r----- 1 root root 1248 May 20 06:47 setuid.changes.3.gz -rw-r----- 1 root adm 4473 Jun 17 06:47 setuid.today -rw-r----- 1 root adm 4473 Jun 3 06:48 setuid.yesterday The obvious thing that confuses me is that the file setuid.yesterday is not from yesterday = Jun/16. Is this a bug?

  Read the article

• Application for time and project management

  - by user10826

  I want to improve the way I organize my projects/tasks/schedule What I do now is: keep an excel sheet with the name of the most important tasks/projects, I look at it at the beginning of each day and decide the ones I will focus on on iCal I write down events for each day, or for a concrete time (13 to 14 hours). I set up each day the tasks I want to accomlish, and allocate them hours I use Things (culture code) to keep info about tasks and projects not very important and which are not time allocated yet (GTD name = someday) I use Mail on Mac and create folders for the mails I want to process with the name of the different projects I save the main info for each project on freemind maps My system works well at the moment but it is pretty complicated to use. I want to make it better and I am looking for something with these requirements: must be 100% offline accessable it should use as less programs/resources as possible, ideally just one program should be able to manage all my info I can use the GTD methodology mixed with priorities and I can allocate each task converted to event on my calendar I can have different daily/weekly, etc views on a calendar to see the "big picture" must run on mac os x leopard price does not matter, I will pay for this So, according to your experience, can you recommend me something like this? Thanks

  Read the article

• Router startup problem

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the pow*emphasized text*er off and on again it all works. The problem is regarding startup only, when I get it to work everything runs as smooth as a 1980-s text-based C++ game on a 3ghz machine. I also have to restart my PC too in order for everything to work. - How can I solve this problem? - Just leave the router turned on all time? I prefer a daily IP switch, though. - May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• Symantec NetBackup restore - Incremental backup

  - by w0051977

  We are using Net Backup as a corporate solution. Incremental backups are taken daily during the week and then a weekly backup is done at the weekend (Saturday). My colleague has restored a folder to how it stood at 14:00 on a Tuesday. The problem is that the restore is taking files from the weekend backup if they did not exist at that point in time of the restore. For example, the folder we are restoring should look like this (this is how it looked on Tuesday at 14:00): Folder1 (folder name) Test.txt Test1.txt Test2.txt The folder looked like this at the weekend when the full restore was done (even though it did exist at the weekend when the full backup ran): Folder1 (folder name) Test.txt Test1.txt Test2.txt Test3.txt The actual folder restored looks like this: Folder1 (folder name) Test.txt Test1.txt Test2.txt Test3.txt Test3.txt should not be restored because it did not exist at the point of the restore. Is there a setting somewhere that we are missing. The folder in question is 200GB - the example above is for simplification. I realise this is a basic question.

  Read the article

• Windows 7 scheduled task returns 0x2

  - by demmith

  I have identical scheduled tasks running in Windows XP Pro and Windows 7. The XP Pro one runs fine, the Windows 7 one always returns 0x2 (which means, "The system cannot find the file specified"; however, executing from the command line is no problem) in the Last Run Result column of the Task Scheduler UI. The scheduled task executes a .bat file daily. The .bat file contains a call to execute a Perl script. As I stated in the previous paragraph, it executes under XP without any trouble but under Windows 7, no dice. The task under Windows 7 is set to "run whether the user is logged on or not." In this case it is me, I am the only user of the system. It is also set to "Run with highest privileges." And it is not hidden. The .bat file executes perfectly well from the command line - it calls the Perl script as expected and the Perl script does its thing. I have searched far and wide looking for an appropriate answer to this issue. So far I have found nothing. What the devil is going on with this Win7 scheduled task? I am ready to pull my hair out.

  Read the article

• How to access previous VHD versions of system backup?

  - by feklee

  Quote from the 31 Oct 2009 TechNet article "Learn more about system image backup": During the first backup, the backup engine scans the source drive and copies only blocks that contain data into a .vhd file stored on the target, creating a compact view of the source drive. The next time a system image is created, only new and changed data is written to the .vhd file, and old data on the same block is moved out of the VHD and into the shadow copy storage area. Volume Shadow Copy Service is used to compute the changed data between backups, as well as to handle the process of moving the old data out to the shadow copy area on the target. This approach makes the backup fast (since only changed blocks are backed up) and efficient (since data is stored in a compact manner). When restoring the image, blocks will be restored to their original locations on the source disk. If you want to restore from an older backup, the engine reads from the shadow copy area and restores the appropriate blocks. For the last days, a daily system backup of drive C: to drive E: has been scheduled and run by Windows 7 Backup and Restore. Drive C: currently holds 233 GB of data, which fits comfortably on drive E:, a 1 TB drive, with 727 GB of free space remaining. How do I access the previous version of a VHD? I right clicked on files and folders in E:\WindowsImageBackup, and I looked for Previous Versions but always: There are no previous versions available

  Read the article

• College network - can I point non-domain student computers to our SUS server?

  - by Joel Coel

  Since I started here 3 months ago, one of the things that's really bothered me about the way this network is setup is something that shows up on the daily bandwidth consumption report. I get a list of top-visited sites by hits and by size, and invariably the top site (to the point that it's bigger than all the other top sites combined) is au.download.windowsupdate.com. We're pulling in ~30GB/day in windows updates. This is every day, not just after a patch Tuesday. After a patch day, it jumps closer to 40GB for a couple days. The key here is that almost none if it is by machines that I'm responsible for. My machines are for the most part fully patched, and when they're not they'll pull from a SUS server, so new updates are downloaded only once. It used to be closer to 50GB/day because most of the machines in our computer labs use DeepFreeze and weren't applying updates correctly, but that's fixed now. So the problem is definitely student-owned machines in the dorms, some of which are re-downloading the same updates in background each day, over and over. I'd love to have these machines start pulling from our SUS server. Then, if they don't ever actually install them at least they're not leeching bandwidth from our public internet connection. Any ideas on how to resolve the situation?

  Read the article

• Syncing two sheets, while being able to hide different data

  - by Joshua

  I'm pretty new to excel- so please bear with me. I have created a spreadsheet to organize gear by serial numbers and by who has it. This list is getting updated multiple times daily as gear shuffles regularly. I have gear that is assigned and unassigned. On the main sheet I have all the data, the way I want it to be organized. What I'm trying to do is duplicate this sheet, so that both sheets automatically keep the same data at all times, but on the first sheet I can hide all the unassigned gear, and view only the assigned gear, and then be able to narrow it down in groups using the hide function heavily. On the second sheet I want to be able to hide all of the assigned gear, and all the columns of gear that have no unassigned gear. End result will be that as gear is moved between individuals or is unassigned entirely, I make that adjustment on one sheet and the data stays the same on both, but the way I view that same sheet is different on both. If I'm making no sense just let me know and I'll try to explain again more clearly. Thanks

  Read the article

• vSphere - datastore falling off a host

  - by Chadddada

  Recently we have been running the vCheck powershell script daily in order to help in monitoring our vSphere ESX 4.0 environment. One of the oddities that we have been seeing is that some of the datastores on the SAN don't always show up on every host. Our hosts are connected redundantly, via FC, to some brocade FC switches, which then connect via fiber to our EMC Ax4 SAN. While all the datastores are presented to each host we have, and they see them initially, they sometimes seem to fall off and are no longer visible. It easy enough to rescan for datastores and add them back to the hosts the hosts but this seems to be an error. Has anyone else seen this or know why it may be happening? Responses to questions: 1. Is it always the same ESX servers that lose their connection? – Scott Warren No this happens randomly on random hosts. If a VM is running on a particular host, of which the VM's disks are on a SAN datastore, then that datastore won't disappear. It seems to happen if a host doesn't touch a datastore for a bit and it just forgets about it.

  Read the article

• should i and how do i backup my database for a webapp that is hosted on amazon ec2 server?

  - by user8184

  I set up an amazon ec2 instance using ubuntu server edition. I install LAMP stack on it. I did up a php web app running on mysql. I have not officially launched, but I need to know this before launching. Should I backup my database data? If so, how should I do it as cost effective as possible? Previously for another web app, i wrote a perl or bash script (cannot remember) that will be executed by cron on a daily basis. The script will then backup the database into a single .sql file and send as email attachment to my gmail account. That web app was on shared hosting hence, I was quite sure i needed to do backup of my database. My files are on git repo so I am not worried about that. Please advise. I am totally unfamiliar with AWS. Only know as much as setting up an account. That is all. Thank you.

  Read the article

• Best Asp.net Hosting

  - by dotnetguts

  There are many asp.net web hosting companies which spends lot on advertisement and also gives you very cheaper rate, as low as $5, but when it comes to support they are simply hopeless. Everyone can you please pass your experience with your past hosting companies and suggest any good asp.net hosting company? Please consider following requirement factors 1) Asp.net 3.5 or 4.0 supported. 2) Url Rewriter support 3) GZip support (Dynamic through code) 4) Initial Setup support (If required) 5) SQL Server 2005 or 2008 6) Allow to access SQL Server DB using SQL Mgmt Studio 7) Environment supporting Backup and Restore of DB on my own, without involving tech support team 8) Full Text Search support 9) FTP support 10) I can able to send atleast 500 Emails daily. 11) 99.9% Up Time (No matter all web hosting say they have 99.9% Up Time, but its not true). 12) Alert Email to be sent when they do any maintenance or during downtime. 13) Hosting Price should be reasonable. Incase you feel i am missing something please add to the list. Can anyone suggest good webhosting company based on above factors?

  Read the article

• How can I create a simple Exchange 2010 backup solution?

  - by bduncanj

  I'm sure this question's been asked a dozen times in one form or another, however after much searching, there doesn't appear to be an obvious simple recovery solution for a single Exchange box. We're using Exchange 2010 on a single server, the server hosts the AD and nothing else on the network uses the AD. The intent is to run this server as you would an externally hosted Exchange server - access only via HTTP (RPC mode or OWA) - all other ports blocked. I've a daily backup running, using Windows Server 2008 volume shadow service to backup the Exchange data to an external hard disk. My question is, how do I perform a bare metal recovery of this server? 1) Do I need to be explicitly including the active directory information in this nightly backup, or will it be there by virtue of the fact that this system is the primary AD server and the Windows backup service knows this? 2) I understand I can re-install Server 2008 onto my new hardware (in the case of hardware failure) and then run Exchange 2010 setup.exe with a /recover argument, referencing the backup volume. 3) It is acceptable to have some downtime during this recovery process. But is there anything else I should be aware of? Thanks! Duncan

  Read the article

< Previous Page | 84 85 86 87 88 89 90 91 92 93 94 95  | Next Page >