Search Results

Search found 2503 results on 101 pages for 'destination'.

Page 88/101 | < Previous Page | 84 85 86 87 88 89 90 91 92 93 94 95  | Next Page >

• Networking issues with Linux server (CentOS 5.3)

  - by sxanness

  I have a Linux server hosting our bug tracking software (CentOS 5.2 Kernel 2.6.18-128.4.1.el5) that I have having some strange network problems with. The machine is configured with two NICS, one for the public interface and the other for our server back end network. The problem is that after doing a service network restart I can ping the public interface and it sends anywhere from 200-500 ICMP packets and then all of a sudden I start getting a request timed out error. Strange but as soon as I connect to the private interface the ping starts working again to the public interface. I clearly have a routing issue somewhere. I have a Juniper Router with the following configuration. Interface 0/0 -- Connect subnet to the ISP at our co-location Interface 0/2 -- For our DRAC network Interface 0/3 -- The Server-backend network (plugs directly into a switch that feeds to all the NICs that are on the 10.3.20.x network. Interface 0/4 -- Plugs directly into another switch that feeds our public interfaces, that interface as all the gateways from our public ip rangs as secondary IP addresses. I hope that someone can ask the right questions that can lead me to check things and figure out what is going on. Has anyone had similar problems and what kind of things should I be checking? Routing issue or something even more complicated? [root@fogbugz ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 # Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ DEVICE=eth0 BOOTPROTO=static IPADDR=72.249.134.98 NETMASK=255.255.255.248 BROADCAST=72.249.134.103 HWADDR=00:16:3E:AA:BB:EE ONBOOT=yes [root@fogbugz ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth1 # Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ DEVICE=eth1 BOOTPROTO=static BROADCAST=10.3.20.255 HWADDR=00:17:3E:AA:BB:EE IPADDR=10.3.20.25 NETMASK=255.255.255.0 NETWORK=10.3.20.0 ONBOOT=yes [root@fogbugz ~]# cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=no HOSTNAME=fogbugz.dfw.hisg-it.net GATEWAY=72.249.134.97 [root@fogbugz ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 72.249.134.96 0.0.0.0 255.255.255.248 U 0 0 0 eth0 10.3.20.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 10.0.0.0 10.3.20.1 255.0.0.0 UG 0 0 0 eth1 0.0.0.0 72.249.134.97 0.0.0.0 UG 0 0 0 eth0

  Read the article

• Networking issues with Linux server (CentOS 5.3)

  - by sxanness

  I have a Linux server hosting our bug tracking software (CentOS 5.2 Kernel 2.6.18-128.4.1.el5) that I have having some strange network problems with. The machine is configured with two NICS, one for the public interface and the other for our server back end network. The problem is that after doing a service network restart I can ping the public interface and it sends anywhere from 200-500 ICMP packets and then all of a sudden I start getting a request timed out error. Strange but as soon as I connect to the private interface the ping starts working again to the public interface. I clearly have a routing issue somewhere. I have a Juniper Router with the following configuration. Interface 0/0 -- Connect subnet to the ISP at our co-location Interface 0/2 -- For our DRAC network Interface 0/3 -- The Server-backend network (plugs directly into a switch that feeds to all the NICs that are on the 10.3.20.x network. Interface 0/4 -- Plugs directly into another switch that feeds our public interfaces, that interface as all the gateways from our public ip rangs as secondary IP addresses. I hope that someone can ask the right questions that can lead me to check things and figure out what is going on. Has anyone had similar problems and what kind of things should I be checking? Routing issue or something even more complicated? [root@fogbugz ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 # Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ DEVICE=eth0 BOOTPROTO=static IPADDR=72.249.134.98 NETMASK=255.255.255.248 BROADCAST=72.249.134.103 HWADDR=00:16:3E:AA:BB:EE ONBOOT=yes [root@fogbugz ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth1 # Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ DEVICE=eth1 BOOTPROTO=static BROADCAST=10.3.20.255 HWADDR=00:17:3E:AA:BB:EE IPADDR=10.3.20.25 NETMASK=255.255.255.0 NETWORK=10.3.20.0 ONBOOT=yes [root@fogbugz ~]# cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=no HOSTNAME=fogbugz.dfw.hisg-it.net GATEWAY=72.249.134.97 [root@fogbugz ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 72.249.134.96 0.0.0.0 255.255.255.248 U 0 0 0 eth0 10.3.20.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 10.0.0.0 10.3.20.1 255.0.0.0 UG 0 0 0 eth1 0.0.0.0 72.249.134.97 0.0.0.0 UG 0 0 0 eth0

  Read the article

• L2TP iptables port forward

  - by The_cobra666

  Hi all, I'm setting up port forwarding for an L2TP VPN connection to the local Windows 2003 VPN server. The router is a simpel Debian machine with iptables. The VPN server works perfect. But I cannot log in from the WAN. I'm missing something. The VPN server is using a pre-shared key (L2TP) and give's out an IP in the range: 192.168.3.0. Local network range is 192.168.2.0/24 I added the route: with route add -net 192.168.3.0 netmask 255.255.255.240 gw 192.168.2.13 (the vpn server) iptables -t nat -A PREROUTING -p udp --dport 1701 -i eth0 -j DNAT --to 192.168.2.13 iptables -A FORWARD -p udp --dport 1701 -j ACCEPT iptables -t nat -A PREROUTING -p udp --dport 500 -i eth0 -j DNAT --to 192.168.2.13 iptables -A FORWARD -p udp --dport 500 -j ACCEPT iptables -t nat -A PREROUTING -p udp --dport 4500 -i eth0 -j DNAT --to 192.168.2.13 iptables -A FORWARD -p udp --dport 4500 -j ACCEPT iptables -t nat -A PREROUTING -p 50 -j DNAT --to 192.168.2.13 iptables -A FORWARD -p 50 -j ACCEPT iptables -t nat -A PREROUTING -p 51 -j DNAT --to 192.168.2.13 iptables -A FORWARD -p 51 -j ACCEPT The whole iptables script is (without the line's from above): echo 1 > /proc/sys/net/ipv4/ip_forward echo 1 > /proc/sys/net/ipv4/tcp_syncookies #Flush table's iptables -F INPUT iptables -F OUTPUT iptables -F FORWARD iptables -t nat -F #Drop traffic iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT ACCEPT #verkeer naar buiten toe laten en nat aanzetten iptables -A FORWARD -i eth0 -o eth1 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE #RDP forward voor windows servers iptables -t nat -A PREROUTING -p tcp --dport 3389 -i eth0 -j DNAT --to 192.168.2.10:3389 iptables -A FORWARD -p tcp --dport 3389 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 3340 -i eth0 -j DNAT --to 192.168.2.12:3340 iptables -A FORWARD -p tcp --dport 3340 -j ACCEPT #toestaan SSH verkeer iptables -t nat -A PREROUTING -p tcp --dport 22 -i eth0 -j DNAT --to-destination 192.168.2.1 iptables -A INPUT -p tcp --dport 22 -j ACCEPT #toestaan verkeer loopback iptables -A INPUT -i lo -j ACCEPT #toestaan lokaal netwerk iptables -A INPUT -i eth1 -j ACCEPT #accepteren established traffic iptables -A INPUT -i eth0 --match state --state RELATED,ESTABLISHED -j ACCEPT #droppen ICMP boodschappen iptables -A INPUT -p icmp -i eth0 -m limit --limit 10/minute -j ACCEPT iptables -A INPUT -p icmp -i eth0 -j REJECT ifconfig eth1 192.168.2.1/24 ifconfig eth0 XXXXXXXXXXXXX/30 ifconfig eth0 up ifconfig eth1 up route add default gw XXXXXXXXXXXXXXXXXXX route add -net 192.168.3.0 netmask 255.255.255.240 gw 192.168.2.13

  Read the article

• Squid 2.7.STABLE3-4.1 as a transparent proxy on Ubuntu Server 9.04

  - by E3 Group

  Can't get this to work at all! I'm trying to get this linux box to act as a transparent proxy and, with the help of DHCP, force everyone on the network to gate into the proxy. I have two ethernet connections, both to the same switch. And I'm trying to get 192.168.1.234 to become the default gateway. The actual WAN connection is to a gateway 192.168.1.1. eth0 is 192.168.1.234 eth1 is 192.168.1.2 Effectively I'm trying to make eth0 a LAN only interface and eth1 a WAN interface. I've oi should set the gateway for eth1 to point to 192.168.1.234 my squid.conf file has the following directives added at the bottom: nly set eth0 to have a gateway address in /etc/network/interfaces I'm not sure whether http_port 3128 transparent acl lan src 192.168.1.0/24 acl lh src 127.0.0.1/255.255.255.0 http_access allow lan http_access allow lh i've added the following routing commands: iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.1.2:3128 iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 I set a computer with TCP settings 192.168.1.234 as the gateway and opened up google.com, but it comes up with a request error. Any ideas why this isn't working? :( Been searching continuously for a solution to no avail. ----------------------------- EDIT ------------------------------- Managed to get it to route properly to the squid, here's the error I get in the browser: ERROR The requested URL could not be retrieved While trying to process the request: GET / HTTP/1.1 Host: www.google.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-GB; rv:1.9.1.2) Gecko/20090729 Firefox/3.5.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-gb,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive Cache-Control: max-age=0 The following error was encountered: * Invalid Request Some aspect of the HTTP Request is invalid. Possible problems: * Missing or unknown request method * Missing URL * Missing HTTP Identifier (HTTP/1.0) * Request is too large * Content-Length missing for POST or PUT requests * Illegal character in hostname; underscores are not allowed Your cache administrator is webmaster. Generated Mon, 26 Oct 2009 03:41:15 GMT by mjolnir.lloydharrington.local (squid/2.7.STABLE3)

  Read the article

• How to allow local LAN access while connected to Cisco VPN?

  - by Ian Boyd

  How can I maintain local LAN access while connected to Cisco VPN? When connecting using Cisco VPN, the server has to ability to instruct the client to prevent local LAN access. Assuming this server-side option cannot be turned off, how can allow local LAN access while connected with a Cisco VPN client? I used to think it was simply a matter of routes being added that capture LAN traffic with a higher metric, for example: Network Destination Netmask Gateway Interface Metric 10.0.0.0 255.255.0.0 10.0.0.3 10.0.0.3 20 <--Local LAN 10.0.0.0 255.255.0.0 192.168.199.1 192.168.199.12 1 <--VPN Link And trying to delete the 10.0.x.x -> 192.168.199.12 route don't have any effect: >route delete 10.0.0.0 >route delete 10.0.0.0 mask 255.255.0.0 >route delete 10.0.0.0 mask 255.255.0.0 192.168.199.1 >route delete 10.0.0.0 mask 255.255.0.0 192.168.199.1 if 192.168.199.12 >route delete 10.0.0.0 mask 255.255.0.0 192.168.199.1 if 0x3 And while it still might simply be a routing issue, attempts to add or delete routes fail. At what level is Cisco VPN client driver doing what in the networking stack that takes overrides a local administrator's ability to administer their machine? The Cisco VPN client cannot be employing magic. It's still software running on my computer. What mechanism is it using to interfere with my machine's network? What happens when an IP/ICMP packet arrives on the network? Where in the networking stack is the packet getting eaten? See also No internet connection with Cisco VPN Cisco VPN Client interrupts connectivity to my LDAP server Cisco VPN stops Windows 7 Browsing How can I prohibit the creation of a route in Windows XP upon connection to Cisco VPN? Rerouting local LAN and Internet traffic when in VPN VPN Client "Allow local LAN Access" Allow Local LAN Access for VPN Clients on the VPN 3000 Concentrator Configuration Example LAN access gone when I connect to VPN Windows XP Documentation: Route Edit: Things I've not yet tried: >route delete 10.0.* Update: Since Cisco has abandoned their old client, in favor of AnyConnect (HTTP SSL based VPN), this question, unsolved, can be left as a relic of history. Going forward, we can try to solve the same problem with their new client.

  Read the article

• DNS "recursion not available" using a Cisco AnyConnect VPN connection

  - by codeape

  Does anyone have experience with configuring Cisco AnyConnect VPN? We have a problem with client DNS name resolution when connected over VPN. To me, it looks as if the Cisco AnyConnect VPN client intercepts DNS queries from the clients. Can someone confirm that the AnyConnect VPN client in fact does this (intercepts DNS traffic)? Where is this configured on the VPN server? EDIT: Here's how the routing table changes when I connect to the VPN: [~] $ diff -u /tmp/route_normal /tmp/route_vpn --- /tmp/route_normal 2010-01-20 19:23:47.000000000 +0100 +++ /tmp/route_vpn 2010-01-20 19:24:46.000000000 +0100 @@ -1,6 +1,10 @@ Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface +xxx.xxx.xx.xx.i 10.0.0.1 255.255.255.255 UGH 0 0 0 ath0 172.16.53.0 * 255.255.255.0 U 0 0 0 vmnet1 10.0.0.0 * 255.255.255.0 U 0 0 0 ath0 +172.17.20.0 * 255.255.255.0 U 0 0 0 cscotun 0 +192.168.111.0 172.17.20.212 255.255.255.0 UG 0 0 0 cscotun 0 172.16.140.0 * 255.255.255.0 U 0 0 0 vmnet8 +172.16.0.0 172.17.20.212 255.255.0.0 UG 0 0 0 cscotun 0 default 10.0.0.1 0.0.0.0 UG 0 0 0 ath0 EDIT 2: The IT guy has done "something" on the VPN endpoint. Now I get "recursion not available" when doing nslookup. The DNS servers have recursion enabled. So it must be the Cisco VPN DNS interception messing this up. ubuntu@domU-12-31-39-00-ED-14:~$ /opt/cisco/vpn/bin/vpn connect xxx.xxxxxx.xx ... >> Please enter your username and password ... >> notice: Establishing VPN... >> state: Connected >> notice: VPN session established to ... ubuntu@domU-12-31-39-00-ED-14:~$ nslookup www.vg.no ;; Got recursion not available from ..., trying next server ;; Got recursion not available from ..., trying next server ;; Got recursion not available from ..., trying next server ;; Got recursion not available from ..., trying next server Server: 172.16.0.23 Address: 172.16.0.23#53 ** server can't find www.vg.no.compute-1.internal: REFUSED ubuntu@domU-12-31-39-00-ED-14:~$ ping 195.88.55.16 PING 195.88.55.16 (195.88.55.16) 56(84) bytes of data. 64 bytes from 195.88.55.16: icmp_seq=1 ttl=240 time=110 ms 64 bytes from 195.88.55.16: icmp_seq=2 ttl=240 time=111 ms 64 bytes from 195.88.55.16: icmp_seq=3 ttl=240 time=109 ms ^C --- 195.88.55.16 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2017ms rtt min/avg/max/mdev = 109.953/110.379/111.075/0.496 ms

  Read the article

• network is not available even when cisco vpn client is connected. wrong route?

  - by javapowered

  I'm using Vodafone 3G modem. I've disabled other network devices in the system (ethernet, wifi, wimax) turned off firewall and antivirus. cisco vpn client connects successfully but I still can not access computer 192.168.147.120 (as well as any other computer from network). Any suggestions are welcome as I don't know what to do. ipconfig /all and route print commands (translated to english): Microsoft Windows [Version 6.1.7601] (C) Microsoft Corporation (Microsoft Corp.), 2009. All rights reserved. C: \ Users \ Oleg> ipconfig / all IP Configuration for Windows The name of the computer. . . . . . . . . : OlegPC The primary DNS-suffix. . . . . . : Node Type. . . . . . . . . . . . . : Hybrid IP-routing is enabled. . . . : No WINS-proxy enabled. . . . . . . : No Ethernet adapter Local Area Connection 4: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Cisco Systems VPN Adapter Physical Address. . . . . . . . . 00-05-9A-3C-78-00 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Local IPv6-address channel. . . : Fe80:: c073: 41b2: 852f: eb87% 26 (Preferred) IPv4-address. . . . . . . . . . . . : 10.53.127.204 (Preferred) The subnet mask. . . . . . . . . . : 255.0.0.0 Default Gateway. . . . . . . . . : IAID DHCPv6. . . . . . . . . . . : 536872346 DUID the client DHCPv6. . . . . . . 00-01-00-01-14-6F-4C-8D-60-EB-69-85-10-2D DNS-servers. . . . . . . . . . . : Fec0: 0:0: ffff:: 1% 1 fec0: 0:0: ffff:: 2% 1 fec0: 0:0: ffff:: 3% 1 NetBios over TCP / IP. . . . . . . . : Disabled Adapter mobile broadband connection through a broadband adapter mobile communications: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Vodafone Mobile Broadband Network Adapter (Huawei) Physical Address. . . . . . . . . 58-2C-80-13-92-63 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes IPv4-address. . . . . . . . . . . . : 10.229.227.77 (Preferred) The subnet mask. . . . . . . . . . : 255.255.255.252 Default Gateway. . . . . . . . . : 10.229.227.78 DNS-servers. . . . . . . . . . . : 163.121.128.134 212.103.160.18 NetBios over TCP / IP. . . . . . . . : Disabled Tunnel adapter isatap. {737FF02E-D473-4F91-840E-2A4DD293FC12}: State of the environment. . . . . . . . : DNS Suffix. DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Adapter Microsoft ISATAP # 3 Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Tunnel adapter isatap. {EF585226-5B07-4446-A5A4-CB1B8E4B13AC}: State of the environment. . . . . . . . : DNS Suffix. DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Adapter Microsoft ISATAP # 4 Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes IPv6-address. . . . . . . . . . . . : 2001:0:4137:9 e76: ea: b77: f51a: 1cb2 (Basically d) Local IPv6-address channel. . . : Fe80:: ea: b77: f51a: 1cb2% 16 (Preferred) Default Gateway. . . . . . . . . ::: NetBios over TCP / IP. . . . . . . . : Disabled C: \ Users \ Oleg> route print ================================================== ========================= List of interfaces 26 ... 00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter 23 ... 58 2c 80 13 92 63 ...... Vodafone Mobile Broadband Network Adapter (Huawei) 1 ........................... Software Loopback Interface 1 19 ... 00 00 00 00 00 00 00 e0 Adapter Microsoft ISATAP # 3 20 ... 00 00 00 00 00 00 00 e0 Adapter Microsoft ISATAP # 4 16 ... 00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface ================================================== ========================= IPv4 Route Table ================================================== ========================= Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.229.227.78 10.229.227.77 296 10.0.0.0 255.0.0.0 On-link 10.53.127.204 286 10.6.93.21 255,255,255,255 10.0.0.1 10.53.127.204 100 10.13.50.12 255,255,255,255 10.0.0.1 10.53.127.204 100 10.53.8.0 255.255.252.0 10.0.0.1 10.53.127.204 100 10.53.127.204 255.255.255.255 On-link 10.53.127.204 286 10.53.128.0 255.255.248.0 10.0.0.1 10.53.127.204 100 10.53.148.0 255,255,255,240 10.0.0.1 10.53.127.204 100 10.53.148.16 255,255,255,240 10.0.0.1 10.53.127.204 100 10.229.227.76 255.255.255.252 On-link 10.229.227.77 296 10.229.227.77 255.255.255.255 On-link 10.229.227.77 296 10.229.227.79 255.255.255.255 On-link 10.229.227.77 296 10.255.255.255 255.255.255.255 On-link 10.53.127.204 286 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.147.0 255,255,255,240 10.0.0.1 10.53.127.204 100 192.168.147.96 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,112 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,128 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,144 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,224 255,255,255,240 10.0.0.1 10.53.127.204 100 192.168.214.0 255.255.255.0 10.0.0.1 10.53.127.204 100 192.168.215.0 255.255.255.0 10.0.0.1 10.53.127.204 100 194.247.133.19 255,255,255,255 10.0.0.1 10.53.127.204 100 213,247,231,194 255,255,255,255 10.229.227.78 10.229.227.77 100 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.229.227.77 296 224.0.0.0 240.0.0.0 On-link 10.53.127.204 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.229.227.77 296 255.255.255.255 255.255.255.255 On-link 10.53.127.204 286 ================================================== ========================= Persistent Routes: None IPv6 Route Table ================================================== ========================= Active Routes: If Metric Network Destination Gateway 16 58:: / 0 On-link 1306:: 1 / 128 On-link 16 58 2001:: / 32 On-link 16 306 2001: 0:4137:9 e76: ea: b77: f51a: 1cb2/128 On-link 16 306 fe80:: / 64 On-link 26 286 fe80:: / 64 On-link 16 306 fe80:: ea: b77: f51a: 1cb2/128 On-link 26 286 fe80:: c073: 41b2: 852f: eb87/128 On-link 1306 ff00:: / 8 On-link 16 306 ff00:: / 8 On-link 26 286 ff00:: / 8 On-link ================================================== ========================= Persistent Routes: None C: \ Users \ Oleg>

  Read the article

• VMWare Network bug in multiple VMWare Workstation versions if using a hardcoded IP address

  - by onyxruby

  I'm having a very tricky problem with some of my VM sessions being unable to reach the Internet or even ping the gateway. I have just set up a new VM Workstation (7) on a W2K8 64bit server (I'll be converting to ESXI 4 once I can find a decent book on it, so for the meanwhile I use workstation). I have imported a number of VM's and setup some new ones on the server.In short the problem with some of the VM's being unable to reach the Internet is that they can't reach the gateway. I've looking at a number of things and can pretty safely rule out the following: Switch, Router, DHCP Server, DNS, Client IP configuration, Routes and typos. The problem is that some of the new clients cannot reach the gateway if their IP address is hardcoded, they can't even ping it by IP address. That rules out DNS and DHCP. Now, if I allow them to get their IP address by DHCP they can reach the gateway and Internet without issue. The interesting thing on this, is that this behavior occurs even if I leave the DNS information hardcoded under TCP/IP settings. It doesn't work unless the IP and gateway are handed out by DHCP even though the same information IP info is being used by the host. Fundamentally from the standpoint of the clients, they are trying to reach the exact same gateway using the exact same IP information regardless of whether they are hardcoded or assigned by DHCP. Here's an example of one client. IP Address 192.168.7.66 - Subnet Mask 255.255.255.0 - Gateway 192.168.7.254 - DNS1 192.168.7.44 - DNS2 192.168.7.254. The issue occurs across six different microsoft operating systems, Windows 7 and Windows 2008 variants all have the issue. My W2K3, XP, Vista and W98 clients all work without issue with hardcoded IP addresses. I have tried things like rearranging the DNS order, flushing DNS and so on. It's not a routing or switch issue as the clients can work just fine if they get their IP by DHCP. It's not a paramater issue as the exact same paramaters are handed out by DHCP as I plug in by hand. It's not a DNS issue as clients cant reach other clients even with IP addresses only. I have run a tracert to the gateway by IP address and it times out on the very first hop before failing on hop3 with destination host unreachable. If I get the IP address by DHCP the tracert finds the gateway (and Internet) without issue. I have read a few other posts online in forums talking about this problem randomly occuring over the years in other VM versions as well, so I suspect some kind of long standing bug. Does anyone have any ideas on this? Is it possibly a bug with Windows 7 and W2K clients under VM?

  Read the article

• ESXi 5.1 ghettoVCB stuck at Clone: 10% done

  - by stormdrain

  Trying to run ghettoVCB for the first time here. I am using a NAS that is set up as a datastore on the host. I did a dry run and it completed without error. The VM is ~500GB and there is only one on the host that I'm trying to backup. I proceeded to start the actual backup: ./ghettoVCB.sh -m vmname -g ghettoVCB.conf It goes though the config and looks like it's taking off: 2013-10-24 11:43:19 -- info: CONFIG - USING GLOBAL GHETTOVCB CONFIGURATION FILE = ghettoVCB.conf 2013-10-24 11:43:19 -- info: CONFIG - VERSION = 2013_01_11_0 2013-10-24 11:43:19 -- info: CONFIG - GHETTOVCB_PID = 17398616 2013-10-24 11:43:19 -- info: CONFIG - VM_BACKUP_VOLUME = /vmfs/volumes/nas2tb-001/esxi4 2013-10-24 11:43:19 -- info: CONFIG - VM_BACKUP_ROTATION_COUNT = 3 2013-10-24 11:43:19 -- info: CONFIG - VM_BACKUP_DIR_NAMING_CONVENTION = 2013-10-24_11-43-18 2013-10-24 11:43:19 -- info: CONFIG - DISK_BACKUP_FORMAT = thin 2013-10-24 11:43:19 -- info: CONFIG - POWER_VM_DOWN_BEFORE_BACKUP = 0 2013-10-24 11:43:19 -- info: CONFIG - ENABLE_HARD_POWER_OFF = 0 2013-10-24 11:43:19 -- info: CONFIG - ITER_TO_WAIT_SHUTDOWN = 4 2013-10-24 11:43:19 -- info: CONFIG - POWER_DOWN_TIMEOUT = 5 2013-10-24 11:43:19 -- info: CONFIG - SNAPSHOT_TIMEOUT = 15 2013-10-24 11:43:19 -- info: CONFIG - LOG_LEVEL = info 2013-10-24 11:43:19 -- info: CONFIG - BACKUP_LOG_OUTPUT = /tmp/ghettoVCB-2013-10-24_11-43-18-17398616.log 2013-10-24 11:43:19 -- info: CONFIG - ENABLE_COMPRESSION = 0 2013-10-24 11:43:19 -- info: CONFIG - VM_SNAPSHOT_MEMORY = 0 2013-10-24 11:43:19 -- info: CONFIG - VM_SNAPSHOT_QUIESCE = 0 2013-10-24 11:43:19 -- info: CONFIG - ALLOW_VMS_WITH_SNAPSHOTS_TO_BE_BACKEDUP = 0 2013-10-24 11:43:19 -- info: CONFIG - VMDK_FILES_TO_BACKUP = all 2013-10-24 11:43:19 -- info: CONFIG - VM_SHUTDOWN_ORDER = 2013-10-24 11:43:19 -- info: CONFIG - VM_STARTUP_ORDER = 2013-10-24 11:43:19 -- info: CONFIG - EMAIL_LOG = 0 2013-10-24 11:43:19 -- info: 2013-10-24 11:43:22 -- info: Initiate backup for vmname 2013-10-24 11:43:22 -- info: Creating Snapshot "ghettoVCB-snapshot-2013-10-24" for serv2 Destination disk format: VMFS thin-provisioned Cloning disk '/vmfs/volumes/esxi4-storage/vmname/vmname_1.vmdk'... Clone: 10% done. and it's been that way for over an hour now. Stuck at Clone: 10% done.. Thing is: I can see the vmdk on the NAS. And it looks like almost the whole thing is there. On the NAS it's showing ~430GB but on vSphere Client Summary is shows as 507GB. I don't see the vmdk on the NAS growing any more. The logfile mimics some of the above and is sitting at "Creating Snapshot..." and nothing else is coming in. Is the vmdk on the NAS showing all those GB because of the provisioning or something? i.e. is the size of the file not necessarily indicative of the amount of actual data that has been copied? Is there are reason it might be "Stuck" at 10%? i.e. could it really be taking this long? Any other tips? Thanks. Edit: as soon as I hit the Submit button, I glance over to see that it has incremented to 11% done. Good to know it'll be complete sometime around when the sun explodes.

  Read the article

• Indirect Postfix bounces create new user directories

  - by hheimbuerger

  I'm running Postfix on my personal server in a data centre. I am not a professional mail hoster and not a Postfix expert, it is just used for a few domains served from that server. IIRC, I mostly followed this howto when setting up Postfix. Mails addressed to one of the domains the server manages are delivered locally (/srv/mail) to be fetched with Dovecot. Mails to other domains require usage of SMTPS. The mailbox configuration is stored in MySQL. The problem I have is that I suddenly found new mailboxes being created on the disk. Let's say I have the domain 'example.com'. Then I would have lots of new directories, e.g. /srv/mail/example.com/abenaackart /srv/mail/example.com/abenaacton etc. There are no entries for these addresses in my database, neither as a mailbox nor as an alias. It's clearly spam from auto-generated names. Most of them start with 'a', a few with 'b' and a couple of random ones with other letters. At first I was afraid of an attack, but all security restrictions seem to work. If I try to send mail to these addresses, I get an "Recipient address rejected: User unknown in virtual mailbox table" during the 'RCPT TO' stage. So I looked into the mails stored in these mailboxes. Turns out that all of them are bounces. It seems like all of them were sent from a randomly generated name to an alias that really exists on my system, but pointed to an invalid destination address on another host. So Postfix accepted it, then tried to redirect it to another mail server, which rejected it. This bounced back to my Postfix server, which now took the bounce and stored it locally -- because it seemed to be originating from one of the addresses it manages. Example: My Postfix server handles the example.com domain. [email protected] is configured to redirect to [email protected]. [email protected] has since been deleted from the Hotmail servers. Spammer sends mail with FROM:[email protected] and TO:[email protected]. My Postfix server accepts the mail and tries to hand it off to hotmail.com. hotmail.com sends a bounce back. My Postfix server accepts the bounce and delivers it to /srv/mail/example.com/bob. The last step is what I don't want. I'm not quite sure what it should do instead, but creating hundreds of new mailboxes on my disk is not what I want... Any ideas how to get rid of this behaviour? I'll happily post parts of my configuration, but I'm not really sure where to start debugging the problem at this point.

  Read the article

• chkdsk, SeaTools, and "does not have enough space to replace bad clusters"

  - by Zian Choy

  When I tried to do a Windows Vista Complete PC Backup, I received an error message that blathered about bad sectors. Then, when I ran chkdsk /r on the destination drive, this is what I got: C:\Windows\system32>chkdsk /R E: The type of the file system is NTFS. Volume label is Desktop Backup. CHKDSK is verifying files (stage 1 of 5)... 822016 file records processed. File verification completed. 1 large file records processed. 0 bad file records processed. 0 EA records processed. 0 reparse records processed. CHKDSK is verifying indexes (stage 2 of 5)... 848938 index entries processed. Index verification completed. 0 unindexed files processed. CHKDSK is verifying security descriptors (stage 3 of 5)... 822016 security descriptors processed. Security descriptor verification completed. 13461 data files processed. CHKDSK is verifying file data (stage 4 of 5)... The disk does not have enough space to replace bad clusters detected in file 239649 of name . The disk does not have enough space to replace bad clusters detected in file 239650 of name . The disk does not have enough space to replace bad clusters detected in file 239651 of name . An unspecified error occurred.f 822000 files processed) Yet, when I ran the SeaTools short & long generic tests on the Seagate disk, I didn't receive any errors. I know that I could reformat the disk and try running chkdsk /r again but I'd prefer to avoid waiting 4 hours in the hope that the problem was magically fixed. On the other hand, if I RmA the drive to Seagate, I have no SeaTools error number to use and they may claim that the drive is just fine. What should I try to do next? Side frustration: There is plenty of free hard drive space. The E: partition has 182 GB free.

  Read the article

• pfSense 2.1 OpenVPN client not using tunnelled interface

  - by Brian M. Hunt

  I'm having some trouble getting OpenVPN working on my pfSense box. The issue is quite strange to me. When I have the OpenVPN turned on, only my router is able to connect to the Internet. From the router I can use ping, links, etc., and connections work exactly as expected - through the VPN, with the IP address assigned by my VPN provider (Proxy.sh, incidentally). However, none of the clients on the local network can connect to the Internet. I get timeouts when using ping or a web browser. I can ping my router, and the IP address of the gateway. When I switch the default gateway from the VPN to my ISP's gateway, all works exactly as expected. Here the routing table (netstat -r) when in VPN mode, and a key for it: IPv4 Destination Gateway Flags Refs Use Mtu Netif Expire 0.0.0.0/1 10.XX.X.53 UGS 0 122 1500 ovpnc1 = default 10.XX.X.53 UGS 0 235 1500 ovpnc1 8.8.8.8 10.XX.X.53 UGHS 0 82 1500 ovpnc1 10.XX.X.1/32 10.11.0.53 UGS 0 0 1500 ovpnc1 10.XX.X.53 link#12 UH 0 0 1500 ovpnc1 10.XX.X.54 link#12 UHS 0 0 16384 lo0 ZZ.XX.XXX.0/20 link#1 U 0 83 1500 re0 ZZ.XX.XXX.XXX link#1 UHS 0 0 16384 lo0 127.0.0.1 link#9 UH 0 12 16384 lo0 128.0.0.0/1 10.11.0.53 UGS 0 123 1500 ovpnc1 192.168.1.0/24 link#11 U 0 1434 1500 ue0 192.168.1.1 link#11 UHS 0 0 16384 lo0 YYY.YYY.YYY.YYY/32 ZZ.XX.XXX.1 UGS 0 249 1500 re0 IP addresses 10.XX.X.53/54 - My DHCP-assigned IP address/pair from the VPN provider ZZ.XX.XXX.XXX - My external IP assigned by my ISP YYY.YYY.YYY.YYY - The external IP assigned by the VPN provider Interfaces ovpnc1 - My VPN client interface re0 - My LAN interface ue0 - My WAN interface This looks essentially what I would expect it to be. The default route is through the VPN provider. The VPN address is routed through the ISP-assigned IP address. I am not sure what would be wrong here. So figuring this was a firewall issue, I basically tried enabling all in/out traffic. This did not seem to remedy the problem. Also figuring it could possibly be some client networking issue, I restarted the clients on the LAN. This did not help. I also ran route flush and reset the routes manually. So I am a bit stumped, and would be very grateful for any thoughts on what the problem might be.

  Read the article

• Squid 2.7.STABLE3-4.1 as a transparent proxy on Ubuntu Server 9.04

  - by LOGIC9

  Can't get this to work at all! I'm trying to get this linux box to act as a transparent proxy and, with the help of DHCP, force everyone on the network to gate into the proxy. I have two ethernet connections, both to the same switch. And I'm trying to get 192.168.1.234 to become the default gateway. The actual WAN connection is to a gateway 192.168.1.1. eth0 is 192.168.1.234 eth1 is 192.168.1.2 Effectively I'm trying to make eth0 a LAN only interface and eth1 a WAN interface. I've oi should set the gateway for eth1 to point to 192.168.1.234 my squid.conf file has the following directives added at the bottom: nly set eth0 to have a gateway address in /etc/network/interfaces I'm not sure whether http_port 3128 transparent acl lan src 192.168.1.0/24 acl lh src 127.0.0.1/255.255.255.0 http_access allow lan http_access allow lh i've added the following routing commands: iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.1.2:3128 iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 I set a computer with TCP settings 192.168.1.234 as the gateway and opened up google.com, but it comes up with a request error. Any ideas why this isn't working? :( Been searching continuously for a solution to no avail. ----------------------------- EDIT ------------------------------- Managed to get it to route properly to the squid, here's the error I get in the browser: ERROR The requested URL could not be retrieved While trying to process the request: GET / HTTP/1.1 Host: www.google.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-GB; rv:1.9.1.2) Gecko/20090729 Firefox/3.5.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-gb,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive Cache-Control: max-age=0 The following error was encountered: * Invalid Request Some aspect of the HTTP Request is invalid. Possible problems: * Missing or unknown request method * Missing URL * Missing HTTP Identifier (HTTP/1.0) * Request is too large * Content-Length missing for POST or PUT requests * Illegal character in hostname; underscores are not allowed Your cache administrator is webmaster. Generated Mon, 26 Oct 2009 03:41:15 GMT by mjolnir.lloydharrington.local (squid/2.7.STABLE3)

  Read the article

• Windows Vista: Networking can only connect "local only"

  - by Damien

  I am attempting to debug a problem on a Windows Vista laptop - not mine! Until just recently (last week or so), it was operating normally for about 4 years :) The problem is that I am having issues connecting to the local network (a basic wireless home router; more later) and the internet (via ADSL). This is both for wired [Broadcom chipset] and wireless [Intel chipset]. I will elaborate further later. To detail the network. I have three other clients (HTC phone, Ubuntu 12.04 desktop [wired] and Ubuntu 10.04 laptop [wireless]), all of whom are able to connect to the network and internet normally. A windows 7 virtual machine running on said desktop connects normally. I have tried two different wireless routers - Netgear DG834G and Netgear DGN3500. The same error mode is common to both. Updating the firmware to the latest on both routers does not help. Overall, it seems safe to say it's localised to the laptop in question. I do not have another Vista client to test with. The specific symptoms are as follows: When "connected", it says "Local Only", and says it cannot connect to the internet. This is true for both wired and wireless. It can get an IP address (192.168.0.5), and the router (192.168.0.1) reports that it can see the device. When I try to ping, I get the following results: ping 192.168.0.1 - (router) all packets lost ping 192.168.0.5 - (laptop's address) OK ping 192.168.0.4 - (desktop) all packets lost Pinging from the desktop to the problematic laptop results in "From 192.168.0.4 icmp_seq=1 Destination Host Unreachable" The most promising "fix" from trawling forums is KB928233 which does not work for me. The problem is persistent across reports (both full shutdown and hibernate) so it appears not to be sleep related. I am not a regular vista user, though I can fumble my way about a bit. Is there any other suggestions as to what I should do? Is there any further information I can provide?

  Read the article

• Static IPv6 address in Windows unused for outgoing connections

  - by Luc

  I'm running a Windows server and trying to get it to use a static IPv6 address for outgoing connections to other IPv6 hosts (such as Gmail). I need this because Gmail requires a ptr record, and I can't set one for random addresses. The static address is configured on the host, but it also has a temporary privacy address as well as a random address from the router it seems. By default Windows uses the privacy address; it seems this is the expected behavior (and it makes perfect sense for people/users that did not set a static address, but I did!). I've tried disabling the privacy address with: netsh int ipv6 set privacy disabled This indeed gets rid of the privacy address, but I still have the random address that the router assigned. To disable this, it was said I needed to disable "router discovery" using this command: net interface ipv6 set interface 14 routerdiscovery=disabled Upon doing this, all IPv6 connectivity is lost. If I do this while pinging Gmail, it will report "Destination host unreachable" as soon as I enter the command. In the static IPv6 configuration, I did configure the default gateway and prefix length, so I don't see why it's unable to connect. Probably has something to do with the lack of ARP in IPv6 and somehow being unable to resolve the router's MAC, but I wouldn't know how to fix this. Finally I've tried disabling the DHCPv6 lease with these commands: netsh interface ipv6 set interface "IDMZ Team" managedaddress=disabled netsh interface ipv6 set interface "IDMZ Team" otherstateful=disabled Which was to no avail; the host continues to obtain and use the router-assigned IPv6 address. The router is a FritzBox 7340, which shows me all the IPv4 and IPv6 addresses that the host (identified by MAC) utilizes, but I'm unable to change the assigned address. Maybe this could be done over the telnet interface of the router somehow, but again, I wouldn't know how to do this even if it's the way to go. In short, any of the following would probably solve my problem: Change Windows' source address selection behavior. Have Windows not get an address from the router and not generate a privacy address; Have the router hand out a static address and make Windows use that as source address. Recover connectivity after disabling router discovery on Windows. Alternatively I might use some (batch, perl, ...) script to throw away all IPv6 addresses except the desired one, but this feels rather hacky. If it's the only way (or less hacky than another hacky solution), it might be an option though. Thanks!

  Read the article

• Detecting upload success/failure in a scripted command-line SFTP session?

  - by Will Martin

  I am writing a BASH shell script to upload all the files in a directory to a remote server and then delete them. It'll run every few hours via a CRON job. My complete script is below. The basic problem is that the part that's supposed to figure out whether the file uploaded successfully or not doesn't work. The SFTP command's exit status is always "0" regardless of whether the upload actually succeeded or not. How can I figure out whether a file uploaded correctly or not so that I can know whether to delete it or let it be? #!/bin/bash # First, save the folder path containing the files. FILES=/home/bob/theses/* # Initialize a blank variable to hold messages. MESSAGES="" ERRORS="" # These are for notifications of file totals. COUNT=0 ERRORCOUNT=0 # Loop through the files. for f in $FILES do # Get the base filename BASE=`basename $f` # Build the SFTP command. Note space in folder name. CMD='cd "Destination Folder"\n' CMD="${CMD}put ${f}\nquit\n" # Execute it. echo -e $CMD | sftp -oIdentityFile /home/bob/.ssh/id_rsa [email protected] # On success, make a note, then delete the local copy of the file. if [ $? == "0" ]; then MESSAGES="${MESSAGES}\tNew file: ${BASE}\n" (( COUNT=$COUNT+1 )) # Next line commented out for ease of testing #rm $f fi # On failure, add an error message. if [ $? != "0" ]; then ERRORS="${ERRORS}\tFailed to upload file ${BASE}\n" (( ERRORCOUNT=$ERRORCOUNT+1 )) fi done SUBJECT="New Theses" BODY="There were ${COUNT} files and ${ERRORCOUNT} errors in the latest batch.\n\n" if [ "$MESSAGES" != "" ]; then BODY="${BODY}New files:\n\n${MESSAGES}\n\n" fi if [ "$ERRORS" != "" ]; then BODY="${BODY}Problem files:\n\n${ERRORS}" fi # Send a notification. echo -e $BODY | mail -s $SUBJECT [email protected] Due to some operational considerations that make my head hurt, I cannot use SCP. The remote server is using WinSSHD on windows, and does not have EXEC privileges, so any SCP commands fail with the message "Exec request failed on channel 0". The uploading therefore has to be done via the interactive SFTP command.

  Read the article

• VPN - force a selective range of ip to run on VPN (linux)

  - by Francesco

  Preface: I know there are similar question here and there however I'm a kind of newbie on Net stuff so I need an answer on this specific scenario, hoping that can help others too as it is a common problem Let say I cannot do anything on the local switch to change the local ip range, I don't want to use any complicate trick as use VMachine to hide the local ip range but I want to use net tools to solve the issue. Scenario my local net assign me an IP of this class 192.168.1.xxx (ex. 192.168.1.116) and my VPN (VPNC) assign me IP of same class 192.168.1.xxx (ex. 192.168.1.247) Obviously I need VPN to access local address (ex. 192.168.1.100) but when I open any address of the class 192.168.1.xx the route point to my local net and not to the VPN ones. I'm on linux and i'd like gui solution (network manager) in case it is not possible let play with route command. here what network manager offer me: Here my actual route once connected to the VPN: Here some route information (route -n) Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 182.71.21.106 192.168.1.1 255.255.255.255 UGH 0 0 0 wlan0 182.71.21.106 192.168.1.1 255.255.255.255 UGH 0 0 0 wlan0 192.168.1.0 0.0.0.0 255.255.255.0 U 9 0 0 wlan0 192.168.1.246 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 Here my ifconfig : ppp0 Link encap:Point-to-Point Protocol inet addr:192.168.1.247 P-t-P:192.168.1.246 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:3415 errors:0 dropped:0 overruns:0 frame:0 TX packets:2525 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:3682328 (3.6 MB) TX bytes:402315 (402.3 KB) wlan0 Link encap:Ethernet HWaddr 4c:eb:42:06:a3:a6 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::4eeb:42ff:fe06:a3a6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:72598 errors:0 dropped:0 overruns:0 frame:0 TX packets:42300 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:76000532 (76.0 MB) TX bytes:13919400 (13.9 MB) The Question So basically I would like to add a rule to force this particular address (192.168.1.100) on the VPN and not on my local net

  Read the article

• DNS and DHCP dies after ~2 days of use on ClearOS

  - by TheLQ

  I'm using ClearOS (based on CentOS, so any info specific to it should apply here) as a gateway, DHCP, and DNS server. I had this server running perfectly for a month or two before replacing it with another server. However due DNS and DHCP failing 2 days in and a host of other performance issues (the box was a little underpowered), I changed back to the origional server. However 2 days in DHCP and DNS are failing again, and I'm out of idea's on why. In both cases to my knowledge no network or server changes occurred after installation. Right after installing (and at least a day in) DNS and DHCP was working just fine. However later (Day 2) I get a call saying their internet is down (translation: Nobody can get to websites because DNS is down) I've tried to fix the problem by checking if the dnsmasq is even running (it is), restarting the service, and restarting the server to no effect. I do have two internal servers that have static DHCP leases but one's lease must of expired as I can't connect to it anymore. I'm hesitant to do any dhcp testing on the last server as I'll not be able to connect to it anymore. Is there anything anyone can think of on why DNS and DHCP would fail 2 days in to running perfectly? More info: Running dnsmasq in debug mode. This is all that's displayed even when running nslookup quackwall. I'm not sure though if nslookup commands should show up in the log [root@quackwall ~]# /usr/sbin/dnsmasq -dq dnsmasq: started, version 2.49 cachesize 150 dnsmasq: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP dnsmasq-dhcp: DHCP, IP range 10.0.0.100 -- 10.0.0.254, lease time 12h dnsmasq: reading /etc/resolv.conf dnsmasq: using nameserver 74.128.17.114#53 dnsmasq: using nameserver 74.128.19.102#53 dnsmasq: read /etc/hosts - 5 addresses dnsmasq-dhcp: read /etc/ethers - 2 addresses On the other server DNS and the Gateway are all configured correctly (10.0.0.2 is quackwall) lordquackstar@quackgame:~$ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.0.0.0 0.0.0.0 255.255.240.0 U 0 0 0 eth0 0.0.0.0 10.0.0.2 0.0.0.0 UG 0 0 0 eth0 lordquackstar@quackgame:~$ cat /etc/resolv.conf nameserver 10.0.0.2 domain highwow.lan search highwow.lan

  Read the article

• Troubleshooting an unstable internet connection

  - by Konrad Rudolph

  My MacBook Pro running OS X (10.9, but I had the same problem before) is connected to a Belkin router via WiFi and, using Virgin Media as the ISP, to the internet. The connection is extremely unstable – on some days, I get a ping timeout every few seconds. In addition, some domains seem to suffer general connectivity issues. For instance, I often find that while the youtube.com website loads, none of the videos (which are hosted on a separate domain) do. At other times, videos load but always fail to buffer, even though the actual connection speed is ok, even though I’ve disabled dash playback. Since I’m living in a rented room and the ISP contract isn’t actually mine I’ve got only limited possibilities of addressing the problem. In particular, I have no access to the router configuration and my non tech savvy landlady, while sympathetic, is not in a great hurry to hand the problem over to the ISP’s customer support. What’s more, I seem to be the only person in the house experiencing these problems – but I can imagine that this is simply because I’m the only one who’s using the internet continuously. I’m searching for specific tests that might be able to pinpoint – and ideally solve – the problem. So far all I’ve managed to do is establish that Virgin is routing my traffic in mysterious ways. Here’s an excerpt from traceroute google.co.uk. It’s worth mentioning that the host name doesn’t seem to matter a lot, the trace route is always the same. traceroute: Warning: google.co.uk has multiple addresses; using 62.254.36.148 traceroute to google.co.uk (62.254.36.148), 64 hops max, 52 byte packets 1 (192.168.2.1) 1.112 ms 1.300 ms 2.359 ms 2 10.100.32.1 (10.100.32.1) 11.926 ms 10.217 ms 24.987 ms 3 cmbg-core-1a-ae3-610.network.virginmedia.net (80.1.202.93) 28.809 ms * 66.653 ms 4 popl-bb-1b-ae16-0.network.virginmedia.net (212.43.163.141) 13.759 ms 126.504 ms 20.472 ms 5 nrth-bb-1b-et-010-0.network.virginmedia.net (62.253.175.57) 28.357 ms 16.398 ms 42.387 ms 6 nrth-bb-1c-ae1-0.network.virginmedia.net (62.253.174.110) 27.441 ms 15.622 ms 12.044 ms 7 lutn-icdn-1-ae0-0.network.virginmedia.net (62.253.175.82) 16.678 ms 28.463 ms 28.253 ms 8 * * * 9 * * * 10 * * * ^C If I let it, this goes on until the end of time. It never seems to reach a destination. Is this normal? A friend living in the same town who is also with Virgin Media has a more conventional traceroute output: 7 hops to google.co.uk, all of which send the ICMP TIME_EXCEEDED response. The obvious fix – rebooting the router – doesn’t seem to help. As far as I can tell, the WiFi connection is stable (I can always ping the router) so the problem is further downstream. I’ve tried using an alternative DNS before (OpenDNS) but if anything, this made things worse. In fact, it made all Google services nigh unreachable.

  Read the article

• VMWare ESXi virtual machine can contact the gateway but not the DNS server

  - by Nathan Palmer

  I am having a bit of a strange issue. I have a VMWare ESXi server with two virtual machines running on it. They are running just fine and can communicate on the network without a problem. I am now trying to add a third. I am installing Ubuntu 8.04 Server. I assign it a static IP address and it's a fresh installation. Once installed I can ping the gateway but I cannot ping the DNS server. It's on the same network with the other two VMs which are communicating just fine. I have tried to reinstall the operating system but it still fails to connect. Here is /etc/network/interfaces auto eth0 iface eth0 inet static address 192.168.1.23 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.1 dns-nameservers 208.67.222.222 #opendns dns-search mydomain.com Here is route Destination | Gateway | Genmask | Flags | Metric | Ref | Use | Iface localnet | * | 255.255.255.0 | U | 0 | 0 | 0 | eth0 default | 192.168.1.1 | 0.0.0.0 | UG | 100 | 0 | 0 | eth0 Since I'm running this behind a FortiGate this is what the sniff command gives me when I try to ping 208.67.222.222 arp who-has 192.168.1.1 tell 192.168.1.23 arp reply 192.168.1.1 is-at MAC 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request As you can see it looks like I never get a response. One interesting thing I notice is the arp reply's MAC doesn't look right. I have cleared the FortiGate's ARP cache though and checked the entry and it seems correct. The MAC it lists is the one for the router. However if I ping from a different virtual machine that is also Ubuntu 8.04 with a nearly identical configuration I get this. 192.168.1.22 -> 208.67.222.222: icmp: echo request 208.67.222.222 -> 192.168.1.22: icmp: echo reply 192.168.1.22 -> 208.67.222.222: icmp: echo request 208.67.222.222 -> 192.168.1.22: icmp: echo reply 192.168.1.22 -> 208.67.222.222: icmp: echo request 208.67.222.222 -> 192.168.1.22: icmp: echo reply So, what could I be missing? Thanks.

  Read the article

• KVM network bridge and public static IP for both host and guests

  - by Javier Martinez

  I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

  Read the article

• KVM network bridge and public static IP for both host and guests

  - by Javier Martinez

  I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

  Read the article

• Can't ping devices by IP address for devices allocated IPs by DHCP

  - by GiddyUpHorsey

  I have a home network with a Trendnet wireless router and a Windows Domain. The Domain Controller/DNS server is a Windows 2000 Server and is configured to forward queries to DNS servers provided by the ISP. The router provides DHCP and is configured with the Windows 2000 Server as the DNS server. The network has been set up for a couple of years and usually works fine. When I connect iPhones to the network over WiFi, the router can ping the iPhones through its browser based admin interface, but Windows machines that are part of the Windows Domain cannot. A laptop was connected to the network over WiFi that wasn't joined to the domain and it could see the iPhones. The router UI shows that the laptop has a reserved IP allocated via DHCP. All machines either have a static or DHCP allocated IP on the 192.168.0.* subnet. Router - 192.168.0.1 - Static - Wired Windows Domain Controller - 192.168.0.8 - Static - Virtual Windows 7 Workstation - 192.168.0.200 - DHCP Auto - Wired VMWare ESXi Host - 192.168.0.201 - Static? - Wired iPhone 1 - 192.168.0.202 - DHCP Auto - WiFi iPhone 2 - 192.168.0.203 - DHCP Auto - WiFi Windows Vista Laptop - 192.168.0.204 - DHCP Reserved - WiFi Using the Windows 7 machine (200), I try to ping each machine and the only DHCP machine that responds is itself. The other DHCP machines fail with Reply from 192.168.0.200: Destination host unreachable.. Using nslookup fails with *** domain.controller.name can't find 192.168.0.203: Non-existent domain. Using the Windows 2000 Domain Controller (8), I try to ping each machine and the only DHCP machine that responds is the Windows 7 machine (200). Pinging the other DHCP machines fails with Request timed out.. Using nslookup also fails with *** domain.controller.name can't find 192.168.0.203: Non-existent domain. Using the iPhone 2 (203), I try to ping (Network Ping Lite) the machines with static IP addresses and that works fine. When I try to ping the Windows 7 machine (200) it is unable to get a response. How do I configure the DNS server/Windows Domain/Router properly so that the Windows Domain machines can see the IPs allocated via DHCP?

  Read the article

• WinXP - Having trouble sharing internet with 3G USB modem via ICS

  - by Carlos Nunez

  all! I've been banging my head against a wall with this issue for a few days now and am hoping someone can help out. I recently signed up for T-Mobile's webConnect 3G/4G service to replace the faltering (and slow) DSL connection in my apartment. The goal was to put the SIM in one of my old phones and use its built-in WLAN tethering feature to share Internet out to rest of my computers. I quickly found out that webConnect-provisioned SIMs do not work with regular smartphones, so I was forced to either buy a 4G-compatible router or tether one of my old laptops to my wireless router and share out that way. I chose the latter, and it's sharpening my inner masochistic self by the day. Here's the setup: GSM USB modem (via hub), ICS host - 10/100 Mbps Ethernet NIC, ICS "guest" - WAN port of my SMC WGBR14N wireless router in bridged mode (i.e. wireless access point). Ideally, this would make my laptop the DHCP server and internet gateway with the WAP giving everyone wireless coverage. I can browse internet on the host laptop fine. However, when clients try to connect, they get a DHCP-assigned IP from the laptop and are able to use the Internet for a few minutes before completely dying. After that happens, they are able to re-associate with the WAP and get IP addresses, but are unable to use Internet or resolve IP addresses until the laptop and router are restarted. If they do get access, it's very, very slow. After running Wireshark on the host machine, it turns out that this is because every TCP connection keeps getting RST. DNS seems to work. I would normally think the firewall is the culprit here, but when it drops packets, it drops them completely. The fact that TCP connections are being ACK'ed by the destination rules that out. Of course, none of the event Log isn't saying anything about what's going on. I also tried disabling power management on the NIC, since that's caused problems in the past; that didn't help either. I finally disabled receive-side scaling as per a Microsoft KB (that applied to Windows Server 2003, SP2) to no avail. I'm thinking of trying it with a different NIC (will be tough; don't have a spare Ethernet NIC around for the laptop), but I'm getting the impression that this simply doesn't work. Can anyone please advise? I apologise for the length of this post; all contributions are much appreciated! -Carlos.

  Read the article

• Windows 8.1 Insufficient storage available to create shadow copy

  - by Bob.at.SBS

  [Note: After I entered the problem statement, I found this question, which is apparently the same problem. Maybe one of us will get a good answer...] I have used the "Windows 7 File Recovery" tool under Windows 8 to create system image backups to an external USB hard drive. I built a new Windows 8.1 machine, and I want to create my first system image backup of that machine to the same USB hard drive. The "Windows 7 File Recovery" tool is gone in Windows 8.1, but wbAdmin is alive and well: wbAdmin start backup -backupTarget:\\?\Volume{2a2b...994f} -allCritical -quiet fails with this text displayed: wbadmin 1.0 - Backup command-line tool (C) Copyright 2013 Microsoft Corporation. All rights reserved. Retrieving volume information... This will back up (EFI System Partition),(C:),Recovery (300.00 MB) to \?\Volume {2a2b1255-3a86-11e3-be86-b8ca3a83994f}. The backup operation to F: is starting. Creating a shadow copy of the volumes specified for backup... Summary of the backup operation: The backup operation stopped before completing. The backup operation stopped before completing. Detailed error: ERROR - A Volume Shadow Copy Service operation error has occurred: (0x8004231f) Insufficient storage available to create either the shadow copy storage file or other shadow copy data. The EFI System Partition is 100 MB The Recovery Partition is 300 MB The C partition is 1.72 TB, NTFS, 218 GB used, 1.51 TB free The destination drive is 1.81 TB, NTFS, 678 GB used, 1.15 TB free I've fiddled with vssadmin resize shadowstorage, with no change in the error. vssadmin list shadowstorage displays: Shadow Copy Storage association For volume: (C:)\?\Volume{37a0...263}\ Shadow Copy Storage volume: (C:)\?\Volume{37a0...263}\ Used Shadow Copy Storage space: 2.39 GB (0%) Allocated Shadow Copy Storage space: 2.81 GB (0%) Maximum Shadow Copy Storage space: 531 GB (30%) Shadow Copy Storage association For volume: (F:)\?\Volume{2a2...94f}\ Shadow Copy Storage volume: (F:)\?\Volume{2a2...94f}\ Used Shadow Copy Storage space: 334 GB (17%) Allocated Shadow Copy Storage space: 337 GB (18%) Maximum Shadow Copy Storage space: UNBOUNDED (922154758%) (Yeah, the "percent calculation" for UNBOUNDED is seriously bogus.) I've run SFC /verifyonly and it seems happy. I've verified that the new `Volume Shadow Copy" service starts when I start the backup operation. Any suggestions?

  Read the article

< Previous Page | 84 85 86 87 88 89 90 91 92 93 94 95  | Next Page >