Search Results

Search found 2436 results on 98 pages for 'hdd cloning'.

Page 88/98 | < Previous Page | 84 85 86 87 88 89 90 91 92 93 94 95  | Next Page >

• Cannot load from raid with grub

  - by Andrew Answer

  I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... This is my partial fdisk -l output: Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Anybody can resolve this issue? I have big headache with this.

  Read the article

• AGP 4x slot running at 2x

  - by Wesley

  Hi all, Here are the specs of the machine related to this question: AMD Athlon XP 2400+ @ 2 GHz / 2x 512MB PC3200 DDR RAM / 3D Fuzion 128MB GeForce 6200 AGP / WD 160GB IDE HDD / FIC AM37 (mobo) / Codegen 350W PSU / Windows XP Pro SP3 So, for some odd reason, the GeForce 6200 that is in the AGP 4x slot is not running at 4x, but 2x. The card itself supports AGP 4x and even 8x. When I enter the BIOS, the options for the AGP slot only allow 2x as the max. Before, the max option for the AGP slot in the BIOS was 4x. (I do get the 4x option after I reset CMOS, but it does not stick after a restart.) I don't exactly know what the problem could be, but a few weeks ago, this machine's hard drive was reformatted and got a fresh install of XP. Also, I did install Rivatuner, but I never overclocked it at all. (I uninstalled it after thinking that it had done something.) Otherwise, I cannot figure out the cause of the problem. Does anybody have an idea why this is happening? (Would I have to do another reformat?) Thanks in advance. PS: the other options for the AGP slot are aperture size (which I tried changing, but it did nothing) and FastWrite (enabled by default).

  Read the article

• How do you recreate the System Recovery environment in Windows 7?

  - by Howiecamp

  I'm running Windows 7 Home Premium RTM (64-bit) and I want to take advantage of the system recovery tools (eg the Command Prompt) without using the Windows 7 DVD. My understanding is that this environment (WinRE) should be installed to your HDD by default as part of the Windows 7 installation. However, when I hit F8 on boot and select "Repair", I get: Windows failed to start. A recent hardware or software change might be the cause. To fix the problem... Status: 0xc000000e Info: The boot selection failed because a required device is inaccessible. The "Info" line seems like the smoking gun. My next step was to boot from the Windows 7 DVD, and choose "Repair". It indicated my Recovery Environment wasn't on the Windows 7 boot menu (perfect) and offered to fix it. I said yes and rebooted, however same issue as above. In addition, when I booted in to Windows 7 and I looked at the boot menu options, the recovery/repair option was not there. Only my Windows installation. Finally, I ran the Disk Management tool (diskmgmt.msc) and took a look at the contents of my "System Reserved" partition (which was set to "Active" as normal). It's unclear to me what the contents should look like, however it is my understanding that the WinRE environment gets installed to this partition. (As part of the above troubleshooting I followed http://superuser.com/questions/25728/how-to-fix-windows-7-boot-process which lead to http://www.sevenforums.com/tutorials/668-system-recovery-options.html).

  Read the article

• Solid State Drive Occasionally Freezes For A Minute While OS Is "Beach Balling"

  - by Boris_yo

  Almost a month ago I bought Intel 330 128GB solid state drive, migrated my data with Intel branded limited-feature Acronis from old HDD to new SSD, optimized with Intel Toolbox and started using it. Occassionally I get close to 1 minute freezes while seeing operating system "beach balls" and animations still work, I can interact and click on something but nothing responds, nothing loads. Recently a couple of such freezes occurred in shorter amount of time in a row. I have noticed that if I stop interacting with laptop, the freeze lasts less time than if I was interacting with laptop. But the bigger problem is when freeze just does not end and computer keeps being stuck unlil it is more than half hour and I run out of patience to keep waiting and feeling I need to restart the system because I am not getting anywhere. Such freeze happened while laptop was cold booting into Windows 7. This is when freeze hang occurred and I had to restart, only later to be greeted with Windows recovery screen stating something about faiure of boot sector and asking to insert Windows repair CD. But after I restarted, Windows booted successfully and all was well. I have filmed video of freeze hang occurring in cold boot which you can see here (on video page look below for description): http://www.youtube.com/watch?v=8b7MQlcDTUs As I have mentioned in the beginning, the SSD is less than a month old but here is S.M.A.R.T statistics just in case (TRIM is enabled btw according to CrystalDiskInfo): I want to emphasize that this SSD is the only drive I have, yet it is working in RAID mode (it was enabled initially in BIOS by previous laptop's owner) on Intel Rapid Storage drivers. I am contemplating about switching to AHCI mode but want to be sure this won't cause data loss. Additionally, the stock firmware is the only firmware available currently, yet Intel does not respond to my posts in their community board. If anyone here has this SSD model or generally has experience with SSD drives, I would love to know your thoughts.

  Read the article

• installed mysql using yum but mysqld dowsnt start: Fedora 16

  - by Sumit Singh Bir

  i installed mysql mysql-server and mysql-libs ... after installation i thought to start the mysql service using command systemctl start mysqld.service Failed to issue method call: Unit mysqld.service failed to load: Invalid argument. See system logs and 'systemctl status mysqld.service' for details. systemctl status mysqld.service this said that it had an invalid argument then i changed the content of mysqld.service with this File: /etc/systemd/system/mysqld.service [Unit] Description=MySQL database server After=syslog.target After=network.target [Service] User=mysql Group=mysql ExecStart=/usr/sbin/mysqld --pid-file=/var/run/mysqld/mysqld.pid ExecStop=/bin/kill -15 $MAINPID PIDFile=/var/run/mysqld/mysqld.pid # We rely on systemd, not mysqld_safe, to restart mysqld if it dies Restart=always # Place temp files in a secure directory, not /tmp PrivateTmp=true [Install] WantedBy=multi-user.target now i found that the error for invalid argument was resolved and mysqld.service was loaded but not enabled ... using systemctl start mysqld.service worked fine ... it workedddd! but then enabling it systemctl enable mysqld.service or service mysqld start did not do anything but the curdor kept on blinking after i pressed enter ... now the thing is that for this f16 i wasted my HDD space for development work and i cannot figure out a way ... please somebody help

  Read the article

• Kindly guide me to buy a new laptop [on hold]

  - by Its me 007

  I am from India. I want to buy a new laptop. Shortlisted few but confused between which processor,Chip set and Graphics will be the best suited for my requirements. NOTE: NOT ABLE TO POST THE LINKS YOU WILL HAVE TO COPY PASTE IT. SORRY. 1) HP Pavilion 15-N004TX - 4th Gen CI5 - 4200U/4GB RAM/500 GB HDD/ 1GB Radeon Graphic - Rs 39990 www.homeshop18.com/hp-pavilion-15-n004tx-laptop-4th-gen-intel-core-i5-4200u-4gb-500gb-15-6-linux-silver-black/computers-tablets/laptops/product:30989197/cid:16317/ 2) Lenovo Essential G510 (59-398452) - 4th Gen Ci5 4200M/ 4GB/ 500 GB/Win8/2GB Graph ATI Sunpro 8570 - Rs 44969 www.flipkart.com/lenovo-essential-g510-59-398452-laptop-4th-gen-ci5-4gb-500gb-win8-2gb-graph/p/itmdp26eprwf5k5v?gclid=CMnh99GA2LoCFaRU4godNiUAGQ&semcmpid=sem_7847244212_laptopsnew_goog&tgi=sem%2C1%2CG%2C7847244212%2Cg%2Csearch%2C%2C24387103114%2C1t1%2Cb%2C%2Blenovo+%2Bg510%2F59+%2B398452%2Cc%2C%2C%2C%2C%2C%2C%2C2 3) HP Pavilion G6-2303TX Laptop (3rd Gen Ci5 3230M/ 4GB/ 500GB/ DOS/ 1GB Graph) - Rs 40500 www.flipkart.com/hp-pavilion-g6-2303tx-laptop-3rd-gen-ci5-4gb-500gb-dos-1gb-graph/p/itmdm6yzh4gr4cxd?pid=COMDM6YHWMGDRDEZ&ref=1d2b85fc-a03d-4c7d-844b-ec9e8dc95a81 4) HP Pavilion 15-E039TX Laptop (3rd Gen Ci5 3230M/ 4GB/ 1TB/ Win8/ 2GB Graph) - Rs 46690 www.flipkart.com/hp-pavilion-15-e039tx-laptop-3rd-gen-ci5-4gb-1tb-win8-2gb-graph/p/itmdn4d9wykhdcpz?pid=COMDN4CZGFMGJNTN&ref=1d2b85fc-a03d-4c7d-844b-ec9e8dc95a81 Now I am confused between: Which Processor and chipset is best? How much graphic card is enough? (Not a gamer) Is any of this laptop future proof i.e. it should at least support upcoming latest programming softwares which eats more processor and memory. Laptop will be mainly used for multiprocessing.It should be at least capable for following: Visual Studio 2012 and the upcoming versions for at least 4 years SQL server 2008 R2 and above Sharepoint Blend Photoshop Kindly suggest. If anyone know any good laptop with good configuration in the 50k budget kindly suggest. Thanks in advance.

  Read the article

• SQLSTATE[HY000]: General error: 2006 MySQL server has gone away

  - by Barkat Ullah

  Server details: RAM: 16GB HDD: 1000GB OS: Linux 2.6.32-220.7.1.el6.x86_64 Processor: 6 Core Please see the link below for my # top preview: I can often see the error mentioned in title in my plesk panel and my /etc/my.cnf configuration are as below: bind-address=127.0.0.1 local-infile=0 datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql max_connections=20000 max_user_connections=20000 key_buffer_size=512M join_buffer_size=4M read_buffer_size=4M read_rnd_buffer_size=512M sort_buffer_size=8M wait_timeout=300 interactive_timeout=300 connect_timeout=300 tmp_table_size=8M thread_concurrency=12 concurrent_insert=2 query_cache_limit=64M query_cache_size=128M query_cache_type=2 transaction_alloc_block_size=8192 max_allowed_packet=512M [mysqldump] quick max_allowed_packet=512M [myisamchk] key_buffer_size=128M sort_buffer_size=128M read_buffer_size=32M write_buffer_size=32M [mysqlhotcopy] interactive-timeout [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid open_files_limit=8192 As my server httpd conf is set to /etc/httpd/conf.d/swtune.conf and the configuration is as below: at prefork.c: <IfModule prefork.c> StartServers 8 MinSpareServers 10 MaxSpareServers 20 ServerLimit 1536 MaxClients 1536 MaxRequestsPerChild 4000 </IfModule> If I run grep -i maxclient /var/log/httpd/error_log then I can see everyday this error: [root@u16170254 ~]# grep -i maxclient /var/log/httpd/error_log [Sun Apr 15 07:26:03 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting [Mon Apr 16 06:09:22 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting I tried to explain everything that I changed to keep my server okay, but maximum time my server is down. Please help me which parameter can I change to keep my server okay and my sites can load fast. It is taking too much time to load my sites.

  Read the article

• MacBook Pro and Backtrack 5R1 Configuration

  - by user119346

  I have a Macbook pro Quad core (2.2/8gb ram/750gb hdd). I have went through tons of forums on the Internet, but none of them seemed to be updated for the current Backtrack 5R1, or the question of getting it to correctly work on the MBP. Can anyone help? I don’t have a USB Dongle, and I want to be able to use the internal airport extreme wireless of the MBP to use BT 5R1. I have downloaded Backtrack 5R1 onto VMWare Fusion, and got it up and running, but to no avail. It keeps recognizing my card as a Ethernet connection. Kismac wont recognize the card either. So what I am asking for is this: The proper “download method.” for Backtrack 5R1 to my MacBook Pro. (YES I AM WILLING TO RE-DOWNLOAD BT 5R1). The Complete process from start to finish, UP TO DATE, from someone who has done this using an MBP Running Lion OSX. The proper tweaks, settings, or commands to get my airport extreme wireless card to work (it is BROADCOM 4331 I think). The wireless connection I need to use the tools on both Backtrack 5R1 and Kismac. I mainly need to test WEP cracking on my network for security. The difference between running BT 5R1 on VMWARE Fusion and running from downloading it directly to the MBP, if there is, How to download it directly to the MBP?

  Read the article

• Update a bootable OS X drive clone with rsync?

  - by Joe

  The question: is it possible to keep a boot-able backup drive clone of OS X updated with rsync? If rsync is not a viable option are there alternatives? The Setup: My situation is as shown above. One internal Samsung 840 SSD [120g] in use as my OS X 10.8 boot disk on a recent model Mac Mini. I have successfully cloned that drive with disk utility to a 125g partition of another HDD in an external USB 3 enclosure and at that point I am able to boot to it. The Goal: As my last system went out in a fiery blaze taking much valuable data with it, I have a new respect for a proper backup solution and really want to do this right. My goal is to achieve an automated differential backup/update from Disk A to Disk B while most importantly maintaining boot-ability on the external drive. And I would prefer to do this differentially to minimize stress on the drives. Hence rsync was the first thing to come to mind. What I have tried: following along with Jamie Zawinski's differential mac bootable backup solution running this manually initially worked - i tested it with only very miniscule file change and everything was fine / external booted and all. now after subsequent passes rsync fails throwing errors particularly relating to updating 'boot.efi' (not at the machine currently I will update the precise log message once I return home) is this a drive partition size issue? does rsync require more space? if it cant be done, are there any alternatives? i've heard whispers of dd

  Read the article

• New to building computers worried about temps

  - by dave

  I'm new to building my own computers and I was wondering about maximum temperatures. I understand that the room temp can affect the computers temp but how relevent is it? I understand that if my room temp is 20°C none of my computer parts could be lower than that. But if my room is 27°C instead of 20°C would this cause my computers parts to heat up more/faster? My new computer I built myself for gaming is i7 2600k 16gb ram ddr3 1600 hd6970 2 gb 240gb ssd ( bought a nas with 3 2tb drives in raid 5 for my home network ) 850w modular psu I also have my old hp computer i3 2120 8gb ram hd6770 1tb hdd I also have 3 laptops in my household, but I am not worried about their temps, they heat up my legs but they are never under stress. Due to size and money reasons I used an old case and it only has one of the sides left on it. Is this bad for the computer and will the extra dust cause problems? Or should I leave it this way or take the missus wrath and buy a case? If so is there any certain case I should get? I don't care about looks I just want card reader and usb slots and for it to run as cool or cooler than now, my case has 1 fan. Also what are the max temps for my new and old computer parts? Is 40°C under load ok for my CPU, what about 70°C for my GPU is that ok too, or should I worry? What are normal and safe temps for my components? I have looked around but there seem to be lots of different answers. I know that 100°C is bad but I want my parts to last as long as possible and this site always seems to give good replies without arguing or flaming.

  Read the article

• Change Windows 7 Explorer's Details Pane limits

  - by Paul

  For some reason, MS decided to completely kill the status bar's functionality in Win7 (and maybe Vista, but I don't know for sure). I have tried all possible options such as Classic Shell and so on. Basically, the one thing I miss most is seeing at a glance the total size of my selected files. I know I can press Alt+Enter or whatever, but that's not the point. The point is that the so-called 'details' pane stops providing details if more than 15 files are selected! WTH? Cannot understand the reason behind such a stupid arbitrary limit, that doesn't seem to be user-configurable at all. Anyway, what I'm looking for is a way to change that limit, either via the registry or otherwise. If changing the limit isn't possible, would it be possible for some programming genius to create a very small optimized light-weight non resource-hungry (you get the idea!) program whose sole purpose will be to automatically click the "Show more details..." link in the details pane after every file selection? For bonus points, the program should wait for a second or two after file selection is complete to do this, so that selecting multiple files in quick succession doesn't hit the HDD repeatedly. Any takers for the challenge? :)

  Read the article

• OpenVZ vs KVM for Linux VMs

  - by Eliasdx

  Hardware: Intel® Core™ i7-920, 12 GB DDR3 RAM, 2 x 1500 GB SATA-II HDD (no SoftRaid because Proxmox developers don't support softraid and they are sure you'll run into problems) Software: Proxmox VE with KVM and OpenVZ support and debian everywhere I want to run multiple Linux VMs on this server. One for a firewall (I want to try pfSense), one for MySQL, one VM for nginx (my stuff) and ~2 VMs with nginx for other people's web sites. I don't think that pfSense will run in an OpenVZ environment but it should run in KVM. The question is if I should setup the other VMs using KVM or OpenVZ. In OpenVZ they should have less overhead for the OS itself but I don't know about the performance. I heard that KVM is more stable but needs more RAM and CPU. I found this diagram showing a OpenVZ setup on the same hardware I'm using. This guy uses an own VM for each and every website which is running on his server. I can't think of any advantage why he's using so many VMs.

  Read the article

• Computer always freezing after random periods of time. No errors listed.

  - by Wesley

  Hi, all. Here are my specs beforehand: AMD Athlon XP 2400+ @ 2.00 GHz, 160GB IDE HDD, 128MB GeForce 6200 AGP, 2 x 512MB PC3200 DDR RAM, CoolMax 350W PSU, 1 x CD-RW Drive, 1 x DVD-ROM Drive, FIC AM37 Mobo, Windows XP Pro SP3 My desktop freezes after random periods of time but there are no errors listed in the Event Viewer after a forced shutdown and restart. A couple months ago, I found that when it froze, the floppy was being accessed at the same time. So, I disconnected the floppy (since I never used it anyways) from the power supply and motherboard. Everything was working fine and the computer never froze. This past Christmas break, I left for a Conference and when I got home, the computer kept freezing again. So, this time, I just disconnected the DVD reader (from mobo and power) and started it up. Still, it froze almost right away. Then I found some older sticks of RAM (2 x 256MB PC2100 DDR) and swapped them in. Everything worked fine again after that. I even swapped the 2 x 512MB PC3200 DDR RAM back in and everything worked okay. Then it started freezing again, and I tried all possible RAM combos, still freezing within 5-10 minutes of startup. One thing I've realized is that the floppy drive is still listed in My Computer and I uninstalled it from my Device Manager already. There were no software errors, and I uninstalled the most recent software, with no effect. Still, I have no idea what is wrong because everything ran fine before that. Any suggestions? EDIT: Still have yet to buy some blank CD media to use Memtest86+. However, would a lack of virtual memory cause the computer to freeze? EDIT2: So after a long time, I ran Memtest86+ and all is well. Turns out though, after removing my original DVD reader and replacing it with a DVD-ROM drive, there is no freezing whatsoever! Thanks for all your suggestions!

  Read the article

• Recommend a free temperature-monitoring utility for cores + video card, on Vista?

  - by smci

  Looking for your recommendations for a free temperature-monitoring utility, for my PC (Core 2) and graphics card for Vista. (Question reposted with the hyperlinks now I have 10 reputation). I don't want all the geeky details, I don't overclock, I don't see the need to mess with my fan speeds or motherboard settings, I just want something fairly basic to help with basic troubleshooting of intermittent overheats on video card and/or mobo: must run on Windows Vista (yes, don't laugh). ideally displays temperature when minimized to toolbar, and/or: automatically alerts me when temperature on either core or the video card exceeds a threshold ideally measures temperature of video card and system as well, not just the cores. HDD temperature is not necessary I think. logging is nice, graphs are also nice portability to Linux and Mac is nice Apparently Everest is the best paid option, but I'm not prepared to spend $40. I found the following free options, but no head-to-head at-a-glance comparison: CoreTemp (only does cores, not video card?) Open Hardware Monitor (nice graphs, displays when minimized to toolbar, no alerts) RealTemp (has alerts, works minimized, lightweight install) HWMonitor (no alerts, CNET: "[free version is] simple but effective") from CPUID CPUCool (not free: 21-day trialware, then $18) SpeedFan from Almico (too geeky, detail overload; CNET: "most users won't be able to make head or tail of the data this utility provides") Motherboard Monitor (CNET: not recommended, requires expert knowledge of your mobo, dangerous) Intel Thermal Analysis Tool (only does cores, not video card? has logging) Useful discussions I found: hardwarecanucks.com , superuser.com 1, 2 , forums.techarena.in (Update: I downloaded Real Temp 3.60 and it meets all my needs, the customizable alert temperature is great. Open Hardware Monitor seems to be the other one that mostly meets my needs, except no alerts; but it is portable. I tried SpeedFan but the interface is very cluttered, too much unnecessary detail (needs a Basic/Advanced mode and a revamp of the interface.) The answer to my underlying issue is nVidia Geforce LE 7500 video card which runs very hot.)

  Read the article

• How can I backup entire installations of a program, instead of just manually backing up individual f

  - by NoCatharsis

  It seems pretty straightforward to backup individual files, such as pictures, saved games, or settings files - just copy them straight over to your 2nd HDD or to an online service like DropBox. However, is there any way to backup entire installations of a program? For instance, my Firefox directory has a lot of personal customizations and add-ons. I don't want to go through each item and decide to back it up or let it go. So my next option is to copy out the entire directory for backup. But, if I copy the entire directory back onto the HD after a format, it is not an integrated installation and this seems like it could be troublesome. I would assume Windows cannot detect the directory for uninstallation, or would not let you choose Firefox as your default browser, right? I'm no pro, but this sounds like a bad idea. So my question is whether there is a good way to preserve all necessary files, while also preserving the full installation process of an application. This is not specific to Firefox - I would like to know how to do this for any application. Thank you.

  Read the article

• A lots of Apache processes are using my CPU uses always more than 70%

  - by Barkat Ullah

  I am running a plesk panel in 1and1. I have 120 sites running and all are using pligg cms, each site has 600 visitors per day. Please see the details of my server below: HDD-1000GB RAM-16GB Processor-6 Core I always see a lot of apache processes running in my # top view, so the server seems overloaded. If I can reduce the amount apache processes I think the server will be ok. But I don't know why too many apache processes are running. Please see the link below for the screenshot of my # top view: http://dl.dropbox.com/u/26967109/%23Top-2.jpg Sometimes I saw too many connection error in my plesk control panel, so I added the below line in my [mysqld] section: set-variable=max_connections=416 But I didn't find a solution yet. I have also added maxclients and serverlimit 416 in the config /etc/httpd/conf/httpd.conf But no solution yet. I am researching around more than 7 days but don't get any solution. Please help me to solve the problem. In peak hours my sites are taking too much time to load, but off-peak hour it is ok. Please help me to find out the actual problem.

  Read the article

• Windows 7 hangs after going into sleep a second time

  - by Brian Stephenson

  I've searched everywhere around Google and can't figure out why this is happening so I decide to ask here to see if anyone has a problem like this. Like it says in the title, whenever I sleep ONCE I'm able to wake the system, but going back to sleep again AFTER waking up for the first time results in it hanging on no input and no output, with the fan spinning as fast as possible and alot of heat being spewed out by the fan as well. I've tried various things like setting all USB Hub Root's to not get switched off for power saving, disabling USB selective suspend, disabling PCI-e link state power management, and even unplugging ALL USB devices and it wont wake up after the second attempt. And I've even waited up to a full hour of the CPU fan spinning loudly and it's still stuck trying to wake up. The only USB devices I use are a Microsoft USB Comfort Curve Keyboard 2000 (IntelliType Pro) and a generic HID compliant mouse from Creative model number OMC90S "CREATIVE MOUSE OPTICAL LITE". My other devices like external drives and controllers are unplugged when I'm not using them as having too many USB devices plugged in at a time causes a deadlock on almost all of the ports I have. Here's my system specifications (Most of these are from CPU-Z): Brand: Gateway DX4300-19 Mainboard: Gateway RS780 Chipset: AMD 780G Rev 00 Southbridge: AMD SB700 Rev 00 LPCIO: ITE IT8718 BIOS: American Megatrends Inc. ver P01-A4 09/15/2009 CPU: AMD Phenom II X4 810 at 2.60 GHz RAM: 8.0 GB DDR2 Dual Channel Ganged Mode at 400 MHz GPU: ATI Radeon HD3200 Graphics Intergrated - RS780 OS: Windows 7 Home Premium x64 OEM (Acer Group) HDD: WDC WD10EADS-22M2B0 1.0 TB (Western Digital Green Caviar) My BIOS has absolutely no control over how I setup the sleep mode to be either S1 or S3. So I can't check these settings or even change them. Hybrid sleep is also disabled, I can successfully go into hibernation and wake from hibernation but this is painfully slow due to a harddrive problem I'm having with this "Green Drive". (Hibernation takes over ~3 minutes to complete) Any help would be appreciated, thanks.

  Read the article

• Time Machine vs Source Control?

  - by Blub

  Finally got convinced to start using some kind of version control for my code instead of zipping down a copy of the project at the end of each day. Downloaded Tortoise SVN and used it to create a repository localy on my hdd. I've been using it for 2 days now but I have to say that using it is actually more hassle than just copying the project manually in explorer. Sure, you only store incremental changes but with the cheap disks of today I can't really say that's an argument when you only have small projects. I haven't realy found a quick way to browse the older versions of my files eighter. What I want is an infinite undo that is completely transparent while I code, if I save the file I want a backup. I don't want to check out, check in and don't even get me started on moving files. I haven't tried Time Machine for OS X but it looks like it's exactly what I'm looking for. Does such a program exist for windows? Preferably free and with some kind of tagging-system so I can tag a timestamp when the project is working etc. Maybe should add that I mostly work alone on a single computer. Update: Some of you asked why I want backup. Since I work alone it's mostly to allow me to quickly hack up a solution without worrying that something will screw up.

  Read the article

• Why dd finishes instantly when pipelining to cat?

  - by agsamek

  I start bash on Cygwin and type: dd if=/dev/zero | cat /dev/null It finishes instantly. When I type: dd if=/dev/zero > /dev/null it runs as expected and I can issue killall -USR1 dd to see the progress. Why does the former invocation finishes instantly? Is it the same on a Linux box? * Explanation why I asked such stupid question and possibly not so stupid question I was compressing hdd images and some were compressed incorrectly. I ended up with the following script showing the problem: while sleep 1 ; do killall -v -USR1 dd ; done & dd if=/dev/zero bs=5000000 count=200 | gzip -c | gzip -cd | wc -c Wc should write 1000000000 at the end. The problem is that it does not on my machine: bash-3.2$ dd if=/dev/zero bs=5000000 count=200 | gzip -c | gzip -cd | wc -c 13+0 records in 12+0 records out 60000000 bytes (60 MB) copied, 0.834 s, 71.9 MB/s 27+0 records in 26+0 records out 130000000 bytes (130 MB) copied, 1.822 s, 71.4 MB/s 200+0 records in 200+0 records out 1000000000 bytes (1.0 GB) copied, 13.231 s, 75.6 MB/s 1005856128 Is it a bug or am I doing something wrong once again?

  Read the article

• Important hardware components to avoid bottlenecks/improve speed on a laptop?

  - by joelhaus

  Looking for a powerful general use (including web development) laptop running Windows. Price points seem to be all over the place. Many less powerful machines are priced much higher than machines with better specs. How does one navigate this market? Are there any unpublished/under-publicized specs/bottlenecks you look for? Understanding that hardware improves over time, is there an efficient ratio that can be used (or something similar, like Windows Experience Index?) which will indicate how powerful a system is? Thanks in advance! P.S. Here is an example from a laptop released on September 17, 2010. Can anyone pick apart these specs? Is there missing information you would be looking for? OS: Win 7 Display: 16.4" LED backlit Processor: Intel Core i7-740QM, 6MB L3 Cache RAM: 6GB DDR3 1333MHz (8GB max.) Graphics: NVIDIA GeForce GT 425M (1 GB of dedicated DDR3) HDD: 500GB 7200RPM SATA Hard Drive Removable Disc: Blue-ray with DVD±R/RW Misc: webcam/mic/speakers/bluetooth (via Sony Vaio VPC-F137FX/B)

  Read the article

• Why is writing to my external hard drive slow, while benchmarks show fast writing?

  - by matix2267

  I have an iOmega eGo 320GB portable drive connected through USB2.0 to my laptop running Windows Vista. It's been working fine for quite some time until recently it became very slow when writing e.g. when copying ~300MB movie over to the drive at first it is extremely fast but it actually doesn't write it only puts in cache and then hangs on last 10-20MBs for about a minute. When copying larger files it's the same story: starts fast but then slows down to ~5MB/s (sometimes even slower down to 2MB/s). Strange thing is that I have always had caching disabled for this drive (it was disabled by default and I never bothered changing it). At first I thought that the disk is dying so I checked S.M.A.R.T. values and everything is fine there. I also run chkdsk and it seemed to fix the problem - it worked fast for a few minutes but then it slowed down again. I also tried plugging it into another USB port - no difference. Additionally I noticed that reading under certain circumstances is sometimes slower e.g. loading times for some games are ~10 times longer, whereas simple copying files from this drive to my internal HDD is fast. I ran a speed benchmark using CrystalDiskMark with a 5x100MB run and strangely got these results: read write (MB/s) Seq 33.05 28.25 512k 17.30 15.27 4k 0.267 0.372 4kQD32 0.510 0.260 This is different from what most other people have (I've found many threads about slow disk write while googling but all of them were slow on benchmarks too) which is why I decided to post this problem here. BTW most of the time when writing (or sometimes reading) the activity led is mostly idle (blinks a while and then stops for longer, sometimes has slower blinks ~1 sek, sometimes goes off for a few seconds - extremely long blink :) ) but when benchmarking, defragmenting or just reading (copying from this drive, installing apps from installers there, watching HD videos) it is blinking really fast (like it should) and there are no slowdowns. It shouldn't be driver issue unless stock Windows drivers have some issues I'm not aware of.

  Read the article

• Getting access to physical drives in ESXi v5.5 installation on Dell PowerEdge R710 with PERC 6/i

  - by Big-Blue

  I've acquired a Dell PowerEdge R710 server a few days ago, which includes a PERC 6/i RAID controller. The server is now fitted with a SATA SSD, one SAS drive and four SATA HDD's, all of which I would like to be passed through to ESXi in an "as-is" state, without creating any logical drives in the RAID controller. Now, the ESXi v5.5 installation image I grabbed from the Dell homepage starts just fine but only lists the logical drives and connected flash drives as possible installation targets, not any of the physical drives. If I create a small logical drive on my SSD (which the PERC 6/i detects as SATA-SSD type), the ESXi install wizard lists the SSD value on that drive as false; which is far from optimal. I have also tried disabling the RAID controller entirely in the setup, but that also did not help. Everything that should enable passthrough is enabled in BIOS, but that shouldn't be a concern at this early stage of the ESXi installation. How would I be able to install ESXi v5.5 to a part of my SSD that is connected to the storage controller, while giving it entire physical access to the disk (to allow for SMART values to be read etc.)?

  Read the article

• Make UEFI, GPT, Bootloader, SSD, USB, Linux and Windows work together

  - by user129552

  I like to use the latest hardware and the latest software; thus I have a Laptop (Lenovo X220) with UEFI instead of BIOS an SSD instead of an HDD GPT partitioning scheme instead of MBR USB to boot from instead of optical disks. I need to use both Windows and Linux. I tried to make them work alongside, but I didn't succeed. Most Linux distribution isos don't even really work on UEFI systems booted from USB. (Not even the self-claimed cutting-edge Fedora. I also tried Linux Mint Debian Edition and Sabayon Linux (according to this guide) which did not work. Only Ubuntu worked for me. I first installed Windows 8 which created sda1: Recovery, sda2: EFI system, sda3: msftres, sda4: NTFS Windows. Windows worked without a problem. I then created sda5: linux-swap and installed Ubuntu into sda6: btrfs. After rebooting, I was not presented GRUB2 as expected, but instead my system just booted into Ubuntu. I could no longer access Windows. After fixing dpkg in btrfs Ubuntu, I followed the Ubuntu documentation on UEFI booting. The result left me with a broken GRUB2, but interestingly, when I wanted to select the device to boot from, I was not only presented the internal SSD, an attached USB device, or LAN, but also Grub2 (broken), Ubuntu and Windows. The result is not very satisfying to me. What would I have to do to fix everything? Or differently asked, what operating system should I install at what point given my possibilities and requirements, so that I have a working bootloader in my UEFI GPT system which presents me a working Linux and Windows.

  Read the article

• Problem with Strange VMWare behaviour when shutting down guest.

  - by adza77

  Hi, I've been having a problem for a while now with VMWare Workstaion. (Originally with 6.5, but now with 7.0 and 7.0.1 too). The problem occurs when I choose to shut down a guest. VMWare itself seems to hang. If I choose to shut down a guest that's opened full screen, and during the process I minimise the screen to work on other applications in the host, often (not all the time) when I return to the guest I have a 'greyed out' screen and the system becomes unresponsive. The host O/S still seems to be working, but I am unable to switch to other applications. (I can bring up the taskbar on the host and 'see' other applications and even switch to them, but VMWare still stays 'on top' being unresponsive). I can not terminate VMWare even when windows says that the application has become unresponsive and gives me the option to terminate. VMWare stays on top, and I'm forced to either shutdown, or log off and log back on in order to regain control of my computer. This happens with both Windows 7 and Windows Vista guest operating systems (32 bit), and I have had it happen on multiple host machines, and multiple guest machines too. Current Host: Windows 7 64 bit, 8GB Ram, 500GB HDD, i7 Processor. I have been searching for more than 6 months for a solution but have found none, so finally decided to post here. Does anyone know what might be causing the problem (+or even how to minimize the VM so I can at least access any other applications and save work before forcing a logoff / reboot+) would be extrememly handly. If I know the correct keystrokes to save and close in an application on the host I can do this by task-switching to the desired app to save and close successfully, but I can't see what I'm doing because VMWare Workstation is still on-top 'greyed' out. Cheers Adam.

  Read the article

• Problem with Strange VMWare behaviour when shutting down guest.

  - by adza77

  Hi, I've been having a problem for a while now with VMWare Workstaion. (Originally with 6.5, but now with 7.0 and 7.0.1 too). The problem occurs when I choose to shut down a guest. VMWare itself seems to hang. If I choose to shut down a guest that's opened full screen, and during the process I minimise the screen to work on other applications in the host, often (not all the time) when I return to the guest I have a 'greyed out' screen and the system becomes unresponsive. The host O/S still seems to be working, but I am unable to switch to other applications. (I can bring up the taskbar on the host and 'see' other applications and even switch to them, but VMWare still stays 'on top' being unresponsive). I can not terminate VMWare even when windows says that the application has become unresponsive and gives me the option to terminate. VMWare stays on top, and I'm forced to either shutdown, or log off and log back on in order to regain control of my computer. This happens with both Windows 7 and Windows Vista guest operating systems (32 bit), and I have had it happen on multiple host machines, and multiple guest machines too. Current Host: Windows 7 64 bit, 8GB Ram, 500GB HDD, i7 Processor. I have been searching for more than 6 months for a solution but have found none, so finally decided to post here. Does anyone know what might be causing the problem (+or even how to minimize the VM so I can at least access any other applications and save work before forcing a logoff / reboot+) would be extrememly handly. If I know the correct keystrokes to save and close in an application on the host I can do this by task-switching to the desired app to save and close successfully, but I can't see what I'm doing because VMWare Workstation is still on-top 'greyed' out. Cheers Adam.

  Read the article

< Previous Page | 84 85 86 87 88 89 90 91 92 93 94 95  | Next Page >