Search Results

Search found 3006 results on 121 pages for 'shutdown hook'.

Page 89/121 | < Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >

• Toshiba wireless is blocked

  - by zorrillo

  I have the same problem, a 32 bits toshiba nb255, it first had the windows 7 bu next I installed the ubuntu 11.04. The wifi does not turn on. I used the following issues the commands rfkill unblock wlan0, sudo ifconfig wlan0 down; they were not able. by setting up the bios in advanced menu, the wireless communication sw in ON, but it did not work also. neither the utilities toshiba nor utilities of ubuntu (wicd, wifi radar). by using gedit to file group, nothing. by installing madwifi packet, nothing. by exporting the wifi driver from windows to ubuntu, by means of the NDISwrapper packet, neither. I put the current scripts of the ouput of the cli root@zorrillo:~# rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes root@zorrillo:~# sudo lspci | grep Atheros 07:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) root@zorrillo:~# root@zorrillo:~# ifconfig -a eth0 Link encap:Ethernet direcciónHW 88:ae:1d:47:df:e1 ACTIVO DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) Interrupción:43 Dirección base: 0xe000 lo Link encap:Bucle local Direc. inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:16436 Métrica:1 Paquetes RX:8 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:8 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:480 (480.0 B) TX bytes:480 (480.0 B) ppp0 Link encap:Protocolo punto a punto Direc. inet:189.203.115.236 P-t-P:192.168.226.1 Másc:255.255.255.255 ACTIVO PUNTO A PUNTO FUNCIONANDO NOARP MULTICAST MTU:1500 Métrica:1 Paquetes RX:6384 errores:30 perdidos:0 overruns:0 frame:0 Paquetes TX:6893 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:3 Bytes RX:5473081 (5.4 MB) TX bytes:974316 (974.3 KB) wlan0 Link encap:Ethernet direcciónHW 00:26:4d:c3:d0:44 DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) note.-it is logical all the counters are cero if the wireless device is down root@zorrillo:/home/zorrillo/Descargas/802BGA# ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill root@zorrillo:/home/zorrillo/Descargas/802BGA# It would seem the wireless switching does not react with whichever ubuntu 11.04 command (I hope to be wrong). The target remains the same, in order of the scripts above. I am worried, I have tried to find any answer for days and nights. Toshiba does not supply drivers or soft support for linux, marketing of course. I only see the device is up by protocols and down phisically, My question is, is it possible to enable or not shutdown physically the device?, because in the toshiba model nb255 the wifi is not set up/down bye means of a physical switch, but by means a combination of Fn + F8 (only for windows 7, no one more), Is there one possibility to configure the hot keys in ubuntu?

  Read the article

• 13.10 upgrade dropping wifi [on hold]

  - by Daryl

  Almost a complete newb here. After my last upgrade from 12.04 to 13.10 my wifi now randomly drops. The only way I can get a signal back is a shutdown and restart otherwise it shows no network is even available to connect to. Had no problems until the upgrade. Any help would be appreciated. H/W path Device Class Description ==================================================== system h8-1534 (H2N64AA#ABA) /0 bus 2AC8 /0/0 memory 64KiB BIOS /0/4 processor AMD FX(tm)-6200 Six-Core Processor /0/4/5 memory 288KiB L1 cache /0/4/6 memory 6MiB L2 cache /0/4/7 memory 8MiB L3 cache /0/d memory 10GiB System Memory /0/d/0 memory DIMM Synchronous [empty] /0/d/1 memory 4GiB DIMM DDR3 Synchronous 1600 MHz (0.6 ns) /0/d/2 memory 2GiB DIMM DDR3 Synchronous 1600 MHz (0.6 ns) /0/d/3 memory 4GiB DIMM DDR3 Synchronous 1600 MHz (0.6 ns) /0/100 bridge RD890 PCI to PCI bridge (external gfx0 port B) /0/100/0.2 generic RD990 I/O Memory Management Unit (IOMMU) /0/100/2 bridge RD890 PCI to PCI bridge (PCI express gpp port B) /0/100/2/0 display Turks PRO [Radeon HD 7570] /0/100/2/0.1 multimedia Turks/Whistler HDMI Audio [Radeon HD 6000 Series] /0/100/5 bridge RD890 PCI to PCI bridge (PCI express gpp port E) /0/100/5/0 bus TUSB73x0 SuperSpeed USB 3.0 xHCI Host Controller /0/100/11 storage SB7x0/SB8x0/SB9x0 SATA Controller [RAID5 mode] /0/100/12 bus SB7x0/SB8x0/SB9x0 USB OHCI0 Controller /0/100/12.2 bus SB7x0/SB8x0/SB9x0 USB EHCI Controller /0/100/13 bus SB7x0/SB8x0/SB9x0 USB OHCI0 Controller /0/100/13.2 bus SB7x0/SB8x0/SB9x0 USB EHCI Controller /0/100/14 bus SBx00 SMBus Controller /0/100/14.2 multimedia SBx00 Azalia (Intel HDA) /0/100/14.3 bridge SB7x0/SB8x0/SB9x0 LPC host controller /0/100/14.4 bridge SBx00 PCI to PCI Bridge /0/100/14.5 bus SB7x0/SB8x0/SB9x0 USB OHCI2 Controller /0/100/15 bridge SB700/SB800/SB900 PCI to PCI bridge (PCIE port 0) /0/100/15.1 bridge SB700/SB800/SB900 PCI to PCI bridge (PCIE port 1) /0/100/15.2 bridge SB900 PCI to PCI bridge (PCIE port 2) /0/100/15.2/0 wlan0 network RT3290 Wireless 802.11n 1T/1R PCIe /0/100/15.2/0.1 generic RT3290 Bluetooth /0/100/15.3 bridge SB900 PCI to PCI bridge (PCIE port 3) /0/100/15.3/0 eth0 network RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller /0/100/16 bus SB7x0/SB8x0/SB9x0 USB OHCI0 Controller /0/100/16.2 bus SB7x0/SB8x0/SB9x0 USB EHCI Controller /0/101 bridge Family 15h Processor Function 0 /0/102 bridge Family 15h Processor Function 1 /0/103 bridge Family 15h Processor Function 2 /0/104 bridge Family 15h Processor Function 3 /0/105 bridge Family 15h Processor Function 4 /0/106 bridge Family 15h Processor Function 5 /0/1 scsi0 storage /0/1/0.0.0 /dev/sda disk 1TB WDC WD1002FAEX-0 /0/1/0.0.0/1 volume 189MiB Windows FAT volume /0/1/0.0.0/2 /dev/sda2 volume 244MiB data partition /0/1/0.0.0/3 /dev/sda3 volume 931GiB LVM Physical Volume /0/2 scsi2 storage /0/2/0.0.0 /dev/cdrom disk DVD A DH16ACSHR /0/3 scsi6 storage /0/3/0.0.0 /dev/sdb disk SCSI Disk /0/3/0.0.1 /dev/sdc disk SCSI Disk /0/3/0.0.2 /dev/sdd disk SCSI Disk /0/3/0.0.3 /dev/sde disk MS/MS-Pro /0/3/0.0.3/0 /dev/sde disk /1 power Standard Efficiency I apologize for my newbness. I hope this is enough info for the hardware. Thanks Bruno for pointing out I needed to add more info. If I am lacking anything else please let me know and I'll post it.

  Read the article

• Developing a Support Plan for Cloud Applications

  - by BuckWoody

  Last week I blogged about developing a High-Availability plan. The specifics of a given plan aren't as simple as "Step 1, then Step 2" because in a hybrid environment (which most of us have) the situation changes the requirements. There are those that look for simple "template" solutions, but unless you settle on a single vendor and a single way of doing things, that's not really viable. The same holds true for support. As I've mentioned before, I'm not fond of the term "cloud", and would rather use the tem "Distributed Computing". That being said, more people understand the former, so I'll just use that for now. What I mean by Distributed Computing is leveraging another system or setup to perform all or some of a computing function. If this definition holds true, then you're essentially creating a partnership with a vendor to run some of your IT - whether that be IaaS, PaaS or SaaS, or more often, a mix. In your on-premises systems, you're the first and sometimes only line of support. That changes when you bring in a Cloud vendor. For Windows Azure, we have plans for support that you can pay for if you like. http://www.windowsazure.com/en-us/support/plans/ You're not off the hook entirely, however. You still need to create a plan to support your users in their applications, especially for the parts you control. The last thing they want to hear is "That's vendor X's problem - you'll have to call them." I find that this is often the last thing the architects think about in a solution. It's fine to put off the support question prior to deployment, but I would hold off on calling it "production" until you have that plan in place. There are lots of examples, like this one: http://www.va-interactive.com/inbusiness/editorial/sales/ibt/customer.html some of which are technology-specific. Once again, this is an "it depends" kind of approach. While it would be nice if there was just something in a box we could buy, it just doesn't work that way in a hybrid system. You have to know your options and apply them appropriately.

  Read the article

• Developing a Support Plan for Cloud Applications

  - by BuckWoody

  Last week I blogged about developing a High-Availability plan. The specifics of a given plan aren't as simple as "Step 1, then Step 2" because in a hybrid environment (which most of us have) the situation changes the requirements. There are those that look for simple "template" solutions, but unless you settle on a single vendor and a single way of doing things, that's not really viable. The same holds true for support. As I've mentioned before, I'm not fond of the term "cloud", and would rather use the tem "Distributed Computing". That being said, more people understand the former, so I'll just use that for now. What I mean by Distributed Computing is leveraging another system or setup to perform all or some of a computing function. If this definition holds true, then you're essentially creating a partnership with a vendor to run some of your IT - whether that be IaaS, PaaS or SaaS, or more often, a mix. In your on-premises systems, you're the first and sometimes only line of support. That changes when you bring in a Cloud vendor. For Windows Azure, we have plans for support that you can pay for if you like. http://www.windowsazure.com/en-us/support/plans/ You're not off the hook entirely, however. You still need to create a plan to support your users in their applications, especially for the parts you control. The last thing they want to hear is "That's vendor X's problem - you'll have to call them." I find that this is often the last thing the architects think about in a solution. It's fine to put off the support question prior to deployment, but I would hold off on calling it "production" until you have that plan in place. There are lots of examples, like this one: http://www.va-interactive.com/inbusiness/editorial/sales/ibt/customer.html some of which are technology-specific. Once again, this is an "it depends" kind of approach. While it would be nice if there was just something in a box we could buy, it just doesn't work that way in a hybrid system. You have to know your options and apply them appropriately.

  Read the article

• C# OpenGL problem with animation

  - by user3696303

  there is a program that simulates a small satellite and requires that a rotation animation of the satellite along the three axes. But when you try to write an animation problem during compilation: the program simply closes (shutdown occurs when swapbuffers, mainloop, redisplay), when you write the easiest programs have the same problem arose. Trying to catch exception by try-catch but here is not exception. How to solve this? I suffer with this a few days. Work in c# visual studio 2008 framework namespace WindowsFormsApplication6 { public partial class Form1 : Form { public Form1() { try { InitializeComponent(); AnT1.InitializeContexts(); } catch(Exception) { Glut.glutDisplayFunc(Draw); Glut.glutTimerFunc(50, Timer, 0); Glut.glutMainLoop(); } } void Timer(int Unused) { Glut.glutPostRedisplay(); Glut.glutTimerFunc(50, Timer, 0); } private void AnT1_Load(object sender, EventArgs e) { Glut.glutInit(); Glut.glutInitDisplayMode(Glut.GLUT_RGB | Glut.GLUT_DOUBLE | Glut.GLUT_DEPTH); Gl.glClearColor(255, 255, 255, 1); Gl.glViewport(0, 0, AnT1.Width, AnT1.Height); Gl.glMatrixMode(Gl.GL_PROJECTION); Gl.glLoadIdentity(); Glu.gluPerspective(45, (float)AnT1.Width / (float)AnT1.Height, 0.1, 200); Gl.glMatrixMode(Gl.GL_MODELVIEW); Gl.glLoadIdentity(); Gl.glEnable(Gl.GL_DEPTH_TEST); Gl.glClear(Gl.GL_COLOR_BUFFER_BIT | Gl.GL_DEPTH_BUFFER_BIT); Gl.glPushMatrix(); double xy = 0.2; Gl.glTranslated(xy, 0, 0); xy += 0.2; Draw(); Glut.glutSwapBuffers(); Glut.glutPostRedisplay(); Gl.glPushMatrix(); Draw(); Gl.glPopMatrix(); } void Draw() { Gl.glLoadIdentity(); Gl.glColor3f(0.502f, 0.502f, 0.502f); Gl.glTranslated(-1, 0, -6); Gl.glRotated(95, 1, 0, 0); Glut.glutSolidCylinder(0.7, 2, 60, 60); Gl.glLoadIdentity(); Gl.glColor3f(0, 0, 0); Gl.glTranslated(-1, 0, -6); Gl.glRotated(95, 1, 0, 0); Glut.glutWireCylinder(0.7, 2, 20, 20); } } }

  Read the article

• Are we queueing and serializing properly?

  - by insta

  We process messages through a variety of services (one message will touch probably 9 services before it's done, each doing a specific IO-related function). Right now we have a combination of the worst-case (XML data contract serialization) and best-case (in-memory MSMQ) for performance. The nature of the message means that our serialized data ends up about 12-15 kilobytes, and we process about 4 million messages per week. Persistent messages in MSMQ were too slow for us, and as the data grows we are feeling the pressure from MSMQ's memory-mapped files. The server is at 16GB of memory usage and growing, just for queueing. Performance also suffers when the memory usage is high, as the machine starts swapping. We're already doing the MSMQ self-cleanup behavior. I feel like there's a part we're doing wrong here. I tried using RavenDB to persist the messages and just queueing an identifier, but the performance there was very slow (1000 messages per minute, at best). I'm not sure if that's a result of using the development version or what, but we definitely need a higher throughput[1]. The concept worked very well in theory but performance was not up to the task. The usage pattern has one service acting as a router, which does all reads. The other services will attach information based on their 3rd party hook, and forward back to the router. Most objects are touched 9-12 times, although about 10% are forced to loop around in this system for awhile until the 3rd parties respond appropriately. The services right now account for this and have appropriate sleeping behaviors, as we utilize the priority field of the message for this reason. So, my question, is what is an ideal stack for message passing between discrete-but-LAN'ed machines in a C#/Windows environment? I would normally start with BinaryFormatter instead of XML serialization, but that's a rabbit hole if a better way is to offload serialization to a document store. Hence, my question. [1]: The nature of our business means the sooner we process messages, the more money we make. We've empirically proven that processing a message later in the week means we are less likely to make that money. While performance of "1000 per minute" sounds plenty fast, we really need that number upwards of 10k/minute. Just because I'm giving numbers in messages per week doesn't mean we have a whole week to process those messages.

  Read the article

• Exchange 2010 DAG Automatic Failover Testing/Issue. Not always automatically failing over to health

  - by Richard

  Ok I've got 2 exchange 2010 servers that run client access/hub transport/mailbox roles and one exchange 2010 server running just client access/hub transport roles and acts as my bridgehead. The two mailbox servers are running one database setup in a DAG. Server A shows the DB Mounted and Server B shows Healthy. If I reboot Server A via windows GUI Server B switches from healthy to mounted and I see hardly any interruption in service using Outlook 2007. Server A shows "Service down", then "Failed" then "Healthy" and leaves the DB mounted on Server B. This is how it should work, so far so good. Now if I test Server A being shut down cold, or unplugging both nics from network to simulate failure, Server B switches from Healthy to Mounted and server A switches to "Service Down" but my outlook client never connects to the DB mounted on server B! I can connect to server C (client access/hub transport) and get to my email and even send new email out, but incoming email doesn't deliver until Server A is brought back online and it's DB goes back to Healthy status. So I don't understand why it auto fail-overs when I reboot the server with the mounted DB copy, causing very little outlook 2007 hiccup if any. But when I shutdown or DC the mounted DB server it DOES mount the healthy copy but outlook 2007 clients can't connect.. I hope the picture I'm trying to paint makes some sense, it's driving me a little batty. Any help would be appreciated!

  Read the article

• Apache reverse-proxy intermittent error 113 - No route to host

  - by BonkaBonka

  I've got an Apache 2.0.52 server on CentOS 4 that front-ends a couple of App servers (mix of Jetty and Tomcat). Apache has a handful of virtual hosts configured like this: <VirtualHost www1.example.com:443> ServerName www1.example.com DocumentRoot "/mnt/app_web/html" SSLEngine on SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP SSLCertificateFile /etc/httpd/conf/ssl.crt/server.crt SSLCertificateChainFile /etc/httpd/conf/ssl.crt/chain.crt SSLCertificateKeyFile /etc/httpd/conf/ssl.key/server.key SetEnvIf User-Agent ".*MSIE.*" nokeepalive ssl-unclean-shutdown downgrade-1.0 force-response-1.0 RewriteEngine on RewriteRule ^/app1/(.*)$ http://app1.example.com:8080/app1/$1 [P,L] RewriteRule ^/app2/(.*)$ http://app2.example.com:8080/app2/$1 [P,L] </VirtualHost> However, I'm getting the following errors in the logs intermittently: [Fri Dec 04 07:19:41 2009] [error] (113)No route to host: proxy: HTTP: attempt to connect to 10.0.0.1:8080 (app1.example.com) failed I initially tried turning off IPv6, and that seemed to largely cure it, but I still have sporadic bursts of these messages. Additionally, we're running memcache on same front-end and during the times when I'm getting those messages in Apache's log, the following command doesn't work: echo stats | nc 127.0.0.1 11211 No messages are printed, but neither are the stats printed. I am completely lost as to how to proceed with troubleshooting this. =(

  Read the article

• Apache is reponding a blank white page

  - by Bruno Araujo

  I have the following situation: A site hosted in apache 2.4, with ssl, that works like a charm for a while now, but out of no where, without modifications to the site, apache started serving random blank pages. The workaround this is to delete the cookies of the browser or restart the browser. I've switched the vitualhost to log in debug mode but it didn't got me anywhere. Here is the debug log of a failed page load: [Wed Oct 24 10:57:35.762547 2012] [ssl:info] [pid 27854:tid 140617706374912] [client 192.168.10.150:58917] AH01964: Connection to child 147 established (server xxx.com.br:443) [Wed Oct 24 10:57:35.762739 2012] [ssl:debug] [pid 27854:tid 140617706374912] ssl_engine_kernel.c(1966): [client 192.168.10.150:58917] AH02043: SSL virtual host for servername xxx.com.br found [Wed Oct 24 10:57:35.777479 2012] [ssl:debug] [pid 27854:tid 140617706374912] ssl_engine_kernel.c(1899): [client 192.168.10.150:58917] AH02041: Protocol: TLSv1, Cipher: DHE-RSA-AES256-SHA (256/256 bits) [Wed Oct 24 10:57:35.779912 2012] [ssl:debug] [pid 27854:tid 140617706374912] ssl_engine_kernel.c(243): [client 192.168.10.150:58917] AH02034: Initial (No.1) HTTPS request received for child 147 (server xxx.com.br:443) [Wed Oct 24 10:57:35.780044 2012] [authz_core:debug] [pid 27854:tid 140617706374912] mod_authz_core.c(809): [client 192.168.10.150:58917] AH01628: authorization result: granted (no directives) [Wed Oct 24 10:57:40.783950 2012] [ssl:info] [pid 27854:tid 140617706374912] (70007)The timeout specified has expired: [client 192.168.10.150:58917] AH01991: SSL input filter read failed. [Wed Oct 24 10:57:40.784077 2012] [ssl:debug] [pid 27854:tid 140617706374912] ssl_engine_io.c(988): [remote 192.168.10.150:58917] AH02001: Connection closed to child 147 with standard shutdown (server xxx.com.br:443)

  Read the article

• iSCSI, failover and XenServer

  - by jemmille

  I have an iSCSI fail over implementation setup so if one of my storage units fails the other takes over immediately (it also runs the NFS shares). When fail over occurs, volumes are exported, the IP is switched to the other machine and the targets are reconfigured. The fail over of the storage system itself works just fine. I use NexentaStor for my filer. When I do a test (manual) fail over of my storage the following occurs: Note: I run the admin VM's on NFS and customer based VM's on iSCSI All NFS based VM's remain up and working perfectly through the failover and after All VM 's running on iSCSI eventually report the following: An error about not being able to write to a particular block An error about journaling not working Then the file system goes RO To get the VM's working again I have to do the following: Force shutdown of the "broken" VM's. Detach the iSCSI SR Re-attach the iSCSI SR Boot the VM on a different server (5 in my pool) If I don't boot on a different server I get this error "Internal error: Failure("The VDI <uuid&gt; is already attached in RW mode; it can't be attached in RO mode!")" The only way I have found to fix that error is to reboot the entire server it was running on previously which is obviously a huge pain. Currently multipathing is NOT enabled (but can be and the same thing still occurs). I have edited much of the /etc/iscsid.conf file to work with the timeout settings but to no avail. In short, my storage fails over properly but XenServer does not keep the connection alive. As a thought, the error that shows up in #4 above might be the ultimate cause and fixing that would fix everything? Any help would be appreciated more than you know.

  Read the article

• Issues with doing a P2V on Exchange 2007

  - by PokermUNKEE

  I shutdown all Exchange services on the physical box and did a convert. Everything converted fine. Server booted up no issues and I could receive email from the outside world with no issues. But I am unable to send emails internally or externally. They just sit in the Outbox. I also disabled the DHCPClient service as I didn't want the server to get an IP address from DHCP when it first came online. It came online with no IP, then I used console to assign the correct static IP address (same one on the physical server) and rebooted. I ran the Exchange Troubleshooting Agent and it gave me the following errors: The value for the '\MSExchangeIS Mailbox\Messages Queued For Submission' counter on server exchange is greater than zero (average value is 8.8) and it appears that 'MSExchangeMailSubmission' is failing to submit messages to at least one computer with the Hub Transport server role installed over the last minute. Found 1 computers with the Hub Transport server role installed in the same Active Directory site as server exchange using local Active Directory site GUID 'ce8a4367-1bf6-4825-9cac-c4e2b115c450'. Check Local Active Directory Site Hub Transport Server Role Health (Mailflow_CheckLocalBhHealth1.1.1.1.1.1.1.1) I have one Exchange server with all the roles on it. Has anyone see this before when doing a convert? Please help :(

  Read the article

• Sending USR2 to mongrel_rails sometimes results in an “Address already in use” on the restart

  - by Ben

  We have a rolling-restart mode for our mongrel cluster that sends a USR2 signal to each running process. This works great, most of the time. But very occasionally the mongrel process will shutdown, and then fail to restart, with the following error: /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/tcphack.rb:12:in `initialize_without_backlog': Address already in use - bind(2) (Errno::EADDRINUSE) from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/tcphack.rb:12:in `initialize' from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel.rb:93:in `new' from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel.rb:93:in `initialize' from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/configurator.rb:139:in `new' from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/configurator.rb:139:in `listener' Looking though the mongrel source, the USR2 handler calls a synchronous stop on the running server, so it ought to block until the socket has been released. Has anyone seen this error? Does anyone have any ideas what might cause it? (I asked this question over on StackOverflow initially, but thought it might be more appropriate here)

  Read the article

• How can I resolve Oracle 11g XE connection failure straight after installation?

  - by d3vid

  I have just installed Oracle 11g XE on a Windows 7 VirtualBox VM, using all the default options. "Getting Started" fails When I click on Getting Started I get taken to http://127.0.0.1:8080/apex/f?p=4950 which fails. After some browsing I came across a suggestion to confirm the HTTP port, but I can't get this far, because I can't connect. connect system fails If I select Run SQL command line I get taken to a SQL prompt. I enter connect system and get prompted for a password. I enter the password. I immediately get the following error: ERROR: ORA-01033: ORACLE initialization or shutdown in progress Process ID: 0 Session ID: 0 Serial number: 0 Info: Start database This happens whether or not I run Start database first. (Start database just opens a Windows command prompt window.) Info: Windows services My Oracle services start as follows: Starting the manual services doesn't resolve the problem. Enabling and starting the disabled service doesn't resolve the problem. Is there something I haven't done? How can I resolve this connection error?

  Read the article

• Vagrant ssh fails with VirtualBox

  - by lukewm

  vagrant up fails when it gets to the ssh part: myterminal$ vagrant up [default] VM already created. Booting if its not already running... [default] Running any VM customizations... [default] Clearing any previously set forwarded ports... [default] Forwarding ports... [default] -- ssh: 22 => 2222 (adapter 1) [default] -- db2: 30003 => 30003 (adapter 1) [default] Cleaning previously set shared folders... [default] Creating shared folders metadata... [default] Booting VM... [default] Waiting for VM to boot. This can take a few minutes. [default] Failed to connect to VM! Failed to connect to VM via SSH. Please verify the VM successfully booted by looking at the VirtualBox GUI. Then when I subsequently try and connect using vagrant ssh or vagrant reload or similar, I get this: myterminal$ vagrant reload [default] Attempting graceful shutdown of linux... SSH connection was refused! This usually happens if the VM failed to boot properly. Some steps to try to fix this: First, try reloading your VM with `vagrant reload`, since a simple restart sometimes fixes things. If that doesn't work, destroy your VM and recreate it with a `vagrant destroy` followed by a `vagrant up`. If that doesn't work, contact a Vagrant maintainer (support channels listed on the website) for more assistance. Please help! I'm really stumped. Kind regards, Luke

  Read the article

• Boot ISO image from GRUB4DOS on EFI machines

  - by Vladimir Tikhomirov

  I failed with loading ISO image (non-distro) from GRUB2 from USB stick, but found the way how I can boot the GRUB4DOS and then load the image from there. However, it doesn't work all the time and the questions is WHY it doesn't? Environment and loading process: We need to have EFI machine, USB stick, booting ISO, GRUB2 and GRUB4DOS. Last 3 on USB stick. Boot: USB - EFI loader - GRUB2 - GRUB4DOS - ISO image Configuration files To boot GRUB4DOS I use this from grub.cfg: menuentry "image.iso" { linux /syslinux/grub.exe --config-file="/menu.lst" } My menu.lst is here: timeout 20 default 0 title image.iso find --set-root --ignore-floppies --ignore-cd //image.iso map --heads=0 --sectors-per-track=0 //image.iso (hd32) map --hook chainloader (hd32) This works perfectly with Legacy machines. However, when I come to GRUB4DOS, I don't see the menu with image.iso, I see only GRUB command line. That means that my menu.lst didn't load. Why is it like this? Background and ideas I have an idea that GRUB4DOS doesn't recognize my USB stick as a device. I tried the command find and got (hd0,0), (hd0,1), (hd0,2), (rd). When I tried to set root to any of these devices I don't see fat file system, how it was with Legacy machines. The root device is (hd0,0), which has ntfs file system which should be partition with Windows. EFI machines support only GRUB2, so I can't boot GRUB4DOS straight away. Please, don't suggest anything like this, because my image doesn't have kernel. You can imagine that you load HDAT2 or Hiren's boot cd, for example. menuentry "Blancco Blancco5.iso" { set isofile="/image.iso" loopback loop $isofile set root=(loop) linux /isolinux/vmlinuz isofile=$isofile splash quiet initrd /isolinux/initrd }

  Read the article

• Install MatroskaProp on Windows 7 x64

  - by Neophytos

  To see more information in Windows Explorer property pages and menus about Matroska Video (.mkv) files, similar to what one can see when selecting native Windows media (.avi, .asf, .wmv or even just plain old mpg) files, Matroska links (from http://www.matroska.org/downloads/windows.html) to a download of the MatroskaProp shell extension (http://www.jory.info/serendipity/archives/14-MatroskaProp-2.8-Released.html). It used to work for me under Windows XP 32-bit. Now I have Windows 7 x64, and downloaded, installed and ran it. Configuration and settings page is fine. But it does not seem to actually register any shell extension. Nothing is added to Explorer windows, menus or property pages when selecting .mkv or .mks files). I tried calling the register hook manually using regsvr32.dll, that again invoked the configuration window and let me set all options, and when confirming even said the registration succeeded, but seems to have had no effect. In the registry I cannot find any traces of the shell extension being installed. Can this extension be made to work under Windows 7 or x64 systems? Are there known problems with installing this or other old shell extensions on x64, or on Windows 7?

  Read the article

• Auto load balancing two node Cluster Hyper-v 2008 R2 enterprise?

  - by Kristofer O

  My setup is a 2 node cluster with 72GB ram each and a ~10TB MD3000i Iscsi SAN. I have about 30VMs running I keep about 15 on either server. I do a live migration to the other server if I need to run updates or whatever... Either one of the servers is able of running all VM if needed, but the cpu is pretty high. Here's my issues. I know Hyper-v has a limit of a single Live-migration at a time. But Why doesn't it queue them up to move one at a time? If I multi select I don't get the option to live migrate a one at a time. OR if I'm in the process of Migrating one it will give me an error that it's currently migrating a VM... Is there a button I missed that will tell a Node that it needs to migrate all the VMs elsewhere? Another question, does anyone know whats the best way to load balance VMs based on CPU and/or network utilzation. I have some VMs that don't do much. and some that trash the CPU or network. I'd like to balance it out on both servers if at all possible. and Is there any way to automate it? last question... If I overcommit my Cluster is there a way to tell the cluster that I want certian VMs the be running and to savestate other VMs based on availible system resources? Say when my one node blue screens and the other node begins starting the VMs up. I want the unimportant ones to shutdown or savestate so the important ones can stay running or come back online. Thanks just for reading all that. Any help would be great.

  Read the article

• kvm works only when kvm-intel is unloaded

  - by Sathya

  I am new to kvm. I have this strange issue. But before explaining the issue, here is my set up. I try to install VM on my Host which is a Acer Laptop 5720 Has T7500 Intel processor. The cpu flags indicate that Virtualization is supported. I run Ubuntu 10.04 (lucid) on it. It comes with kvm. Now coming to the issue - I dont get any errors while executing "sudo modprobe kvm-intel". So I presume my processor does indeed support hardware virtualization. I use virt-manager and create a VM on which I install ubuntu from an *.iso file. When I start the VM it says it is running. No signs of any trouble. I can see the domain list in "virsh list". But when I try to connect to the VM thru VNC, all I get to see is a blank screen (no cursor). There is no response to any key press. I changed the video mode etc. Tried all different combinations but none work. But strangely, if I shutdown the vm an virt-manager and then unload the module by doing "sudo modprove -r kvm-intel", everything works fine. ie., I can see the screen via VNC. I am able to install the OS and so on. So what does this mean ? IS hardware virtualization not supported ? How come there is no error anywhere ? dmesg | grep kvm doesnt report anything. Can someone throw light on what excatly is happening ?

  Read the article

• How to configure Hyper-V failover cluster to live migrate when dynamic memory runs out?

  - by Matt Johnson

  Appologies in advance that this is not a direct programming question, but I have a feeling that the solution involves custom powershell scripts (maybe), so this is as good a place to ask as any. I maintain a website that has a large Hyper-V cluster for SQL Servers. We are using Windows 2008 R2 SP1, and the new "dynamic memory" feature. I've already ready reviewed the Best Practices Guide, and implemented it's suggested configuration. Everything works well, except that when SQL demand increases memory pressure to expand to more memory than is available on the physical machine, the memory status goes into the "Warning" state and stays there. I assume the hypervisor is using a swapfile on the host to fulfill the memory requirement, thus slowing the virtual machine down. When this happens, there are plenty of other nodes in the cluster that have available resources. I can live-migrate the virtual server over there and everything works, and the warnings go away. Now how can I automate this? I see no menu options in either Hyper-V or the Failover Cluster Manager for performing a migration or shutdown when dynamic memory goes into the warning state. Any ideas about how to script this, or monitor it and invoke the action directly, would be helpful. If the solution involves coding, powershell would be ideal, but I could envison this as a .Net Service that monitors for this state and kicks off the migration request. I just don't know what objects are involved in doing the monitoring or kicking off the live migration. Thanks in advance.

  Read the article

• Accidently overwrote system.dbf - What now?

  - by Filip Ekberg

  I accidentally overwrote system.dbf in /usr/lib/oracle/xe/oradata/XE/system.dbf Well I did not actually do it accidentally, however I overwrote it because of other failures in the database. And when I try running the following: SQL> shutdown ORA-01109: database not open Database dismounted. ORACLE instance shut down. SQL> startup ORACLE instance started. Total System Global Area 289406976 bytes Fixed Size 1258488 bytes Variable Size 92277768 bytes Database Buffers 192937984 bytes Redo Buffers 2932736 bytes Database mounted. ORA-01589: must use RESETLOGS or NORESETLOGS option for database open Now I want to try to Recover the database because starting it in mounted or standard surely doesn't work. SQL> recover database using backup controlfile; ORA-00283: recovery session canceled due to errors ORA-01110: data file 1: '/usr/lib/oracle/xe/oradata/XE/system.dbf' ORA-01122: database file 1 failed verification check ORA-01110: data file 1: '/usr/lib/oracle/xe/oradata/XE/system.dbf' ORA-01206: file is not part of this database - wrong database id How do I solve this? Is it even possible? My "real" problem was that I ran the /etc/init.d/oracle-xe configure and it overwrote my old configuration and probably removed passwords and such so my tables were gone, however I found the mytablespace.dbf so I hope that it is possible to recover? Please shed some light on this.

  Read the article

• MySQL socket connections working, but not port connections

  - by Neil

  I installed MySQL community 5.1.45 on my Snow Leopard 10.6, using the pkg from their site. I had previously installed a MySQL binary from entropy.ch. In the previous installation, the connections were working fine before I upgrade to Snow Leopard. In Snow Leopard, both the installations are problematic. Using an app called Sequel Pro, if I connect with the socket operation, it connects properly. However, a standard connection with the same credentials doesn't work. From what I've understood, socket connections happen on the machine itself between processes, whereas normal connections occur over the network/ports, in this case a loopback to my machine, since the server and client are both on the same machine. My new CakePHP installation isn't being able to connect to the db with the root credentials I provided. Btw, I've been starting the MySQL server using the Preference Pane. When I tried running mysqld from terminal, it gave me: 100323 1:54:37 [Warning] Can't create test file /usr/local/mysql-5.1.45-osx10.6-x86_64/data/mbp.lower-test 100323 1:54:37 [Warning] Can't create test file /usr/local/mysql-5.1.45-osx10.6-x86_64/data/mbp.lower-test mysqld: Can't change dir to '/usr/local/mysql-5.1.45-osx10.6-x86_64/data/' (Errcode: 13) 100323 1:54:37 [ERROR] Aborting 100323 1:54:37 [Note] mysqld: Shutdown complete mbp is the name of my machine. How do I fix this so that my webserver can connect to the mysql server?

  Read the article

• SQL Server instance shuts down

  - by user42119

  I'm currently developing a new ASP.NET project hosted on a Windows Server 2008 RC2 with an SQL Server 2008 Express database. I have three SQL Server instances (for different purposes) running which currently all contain a single database. For apparently no reason, these instances tend to shut down after some days. There might be low or no traffic to these instances, because there might be some days in a row, where I can't develop. It now occurred several times, that one or two of these three instances just shut down, so that I can't access the database, without manually starting the instance. I can't seem to find a event log entry for the shutdown, which is most likely because I just enabled logging (why is the default setting off?). So the questions are: * Why does an SQL Server instance shut down? (Is there such a thing as a "Shut down instance after 3 days of inactivity"? * How can I achieve that the instances are running 24/7? Edit: I solved this problem by writing my own application that checks for the status of the SQL Server services. My program will start via a batch file, that gets called by the Windows Task Scheduler every 5 minutes.

  Read the article

• Experience with AMCC 3ware 9650se raid cards? Ours seems dead

  - by antiduh

  We have a 8-port 3ware 9650se raid card for our main disk array. We had to bring the server down for a pending power outage, and when we turned the machine back on, the raid card never started. This card has been in service for a couple years without problems, and was working up until the shutdown. Now, when we turn the machine on, the bios option rom that normally kicks in before the bootloader doesn't show up, none of the drives start, and when the OS tries to access the device, it just times out. The firmware on it has been upgraded in the past, so it's possible we've hit some sort of firmware bug. We're using it in a Silicon Mechanics R272 machine with gentoo for the OS. The OS eventually boots, but alas, without the card. We've ordered a new one, but I'm worried that if we replace the card it won't recognize the existing array. Has anybody performed a card swap before? Any help would be greatly appreciated. Edit: These are the kernel errors we see: 3ware 9000 Storage Controller device driver for Linux v2.26.02.012. 3w-9xxx 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 3w-9xxx 0000:09:00.0: setting latency timer to 64 3w-9xxx: scsi0: ERROR: (0x06:0x000D): PCI Abort: clearing. 3w-9xxx: scsi0: ERROR: (0x06:0x001F): Microcontroller not ready during reset sequence. 3w-9xxx: scsi0: ERROR: (0x06:0x0036): Response queue (large) empty failed during reset sequence. 3w-9xxx 0000:09:00.0: PCI INT A disabled

  Read the article

• What DBus signal is sent on system suspend?

  - by Paul Robinson

  Hello, I need to detect when a machine is going to sleep in Ubuntu 9.10 and Fedora 13. Both use UPower, so I've been looking on the "org.freedesktop.UPower" DBus bus for such signals. I've been listening for the "sleeping" signal on the UPower bus with the following command: dbus-monitor --system "type='signal',interface='org.freedesktop.UPower',member='Sleeping'" When I sleep the machine (either by closing the lid, selecting "shutdown - suspend" or sending a DBus message) I don't see a "sleeping" event. I notice that the "Sleeping" event is sent when the "org.freedesktop.UPower.AboutToSleep" method is invoked. I can do this manually by calling: dbus-send --print-reply --system --dest=org.freedesktop.UPower /org/freedesktop/UPower org.freedesktop.UPower.AboutToSleep And I notice the "sleeping" signal is fired. My understanding is that anything that sleeps the PC must send the "AboutToSleep" signal before hand. It doesn't seem like this is happening. I've tried these steps on both Fedora 13 and Ubuntu 9.10 and I see the same results. Can anyone explain what's happening or provide me with an alternative DBus signal to listen for? Many thanks, Paul

  Read the article

• port forwarding with VirtualBox

  - by Argh

  I have a virtualbox VM running ubuntu. The Ubuntu guest is running a web server which listens on port 3000 (http://127.0.0.1:3000) The host machine is windows vista. I have configured port forwarding using VBoxManage. If I query the config using VboxManage getextradata "MyMachine", I get Key: GUI/AutoresizeGuest, Value: on Key: GUI/Fullscreen, Value: off Key: GUI/LastCloseAction, Value: shutdown Key: GUI/LastWindowPostion, Value: 9,34,640,529,max Key: GUI/MiniToolBarAlignment, Value: bottom Key: GUI/MiniToolBarAutoHide, Value: off Key: GUI/SaveMountedAtRuntime, Value: yes Key: GUI/Seamless, Value: off Key: GUI/ShowMiniToolBar, Value: yes Key: VBoxInternal/Devices/pcnet/0/LUN#0/Config/guesthttp/GuestPort, Value: 3000 Key: VBoxInternal/Devices/pcnet/0/LUN#0/Config/guesthttp/HostPort, Value: 3000 Key: VBoxInternal/Devices/pcnet/0/LUN#0/Config/guesthttp/Protocol, Value: TCP This looks like it should work... However when I try to access the web server from the host machine (windows box) I dont get a response. I ran a netstat on the windows box and nothing appears to be listening on port 3000 which explains why forwrding isnt working. Note that I have already tested with my firewall switched off... The version of VirtualBox I am using is 3.1.4 Any ideas?

  Read the article

< Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >